Table Of Contents

The Remote Transmitter ............................................................................................................. 3

The Valet Switch ........................................................................................................................ 3
The Red LED Status Light ......................................................................................................... 4
Transmitter Operations ............................................................................................................... 4
Active Arming The Security System Using The Transmitter .................................................... 5
Arming Bypass ........................................................................................................................ 5-6
Auxiliary Sensor Bypass ............................................................................................................ 6
Passively Arming The Security System With The Last Door Arming Feature ...................... 6-7
Security System Armed And Activated .................................................................................. 8-9
"Protect Yourself And Your Investment" Disarming The Security System ................................................................................................. 9
Safety Disarm/Storm Mode ...................................................................................................... 10
Automatic Rearming ................................................................................................................ 10
OWNER'S MANUAL Remote Panic ............................................................................................................................ 11
The Valet Switch And Valet Modes ................................................................................... 11-12
Valet Override - Disarming The Security System Without The Transmitter .......................... 12
Red LED Status Light - Security System Status ................................................................. 13-15
Siren And Parking Light Confirmation ............................................................................... 15-16
Shock Detection And Prewarn Circuit ..................................................................................... 17
Trunk Release And 3rd Channel Output .................................................................................. 17
MODEL: 200+P Programmable Features ....................................................................................................... 18-25
Total System Reset .............................................................................................................. 25-26
Encoding Transmitters ........................................................................................................ 26-27
COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT 1999 Second Vehicle Operation ........................................................................................................ 27
Limited Lifetime Warranty ........................................................................................ Back Cover

Introduction The Red LED Status Light: Informs you of the different conditions the system can
be in and also serves as a visual deterrent to break-ins and theft. Please spend time reviewing
Congratulations on your purchase of this vehicle security system. In learning to this guide and to become familiar with your vehicle security system.
operate your security system, please become familiar with the following three principal
components: the Remote Transmitter, the Red LED Status Light, and the Valet Switch.
Transmitter Operations
The Remote Transmitter: Each security system comes with two pre-learned LED Light- Illuminates when
transmitters, but can learn up to 4 different transmitters. The transmitter has two buttons: the Transmitter is operating. Small Transmitter Button-
one large button and a smaller button. This system is pre-programmed, through a built-in Pressing this button alone for 2
learning routine, to have the transmitter buttons work in the following configuration: Large Transmitter Button- seconds can be used to remotely
The large button is used to arm, disarm and panic the security system. Pressing and releasing this open the trunk. If this button is
The small button pressed for 2 seconds operates the optional trunk release feature. button will arm and disarm pressed twice within 2 seconds
Pressing the small button twice within two seconds will arm or disarm the system without the alarm, which optionally the system will arm or disarm
the siren chirp confirmation (silent arm/disarm). The small button can be used, in locks and unlocks the doors. without the confirmation siren
conjunction with the large button, to operate remote sensor bypass. Pressing and holding this chirps. If this button is pressed
Both buttons pressed together can be used to activate the 3rd Channel output or engage button for 2 seconds will within 5 seconds after arming
the Anti-Carjacking feature, provided it is programmed to operate. "Panic" the alarm- sounding the system, the shock sensor, if
the siren, flashing the exte- present, will be bypassed.
The Valet Switch: This switch is used to prevent automatic system functions such rior lights.
as Last Door Arming or Automatic Rearming by placing the system into Valet Mode. The
Both The Large and Small
Valet Switch is also used, with the ignition key, to disarm the security system in the event
Transmitter Buttons- Pressing these buttons together for 3 seconds will engage the 3rd
the transmitter becomes inoperable, and this switch is also used in the procedure for
Channel Output or the programmable Anti-Carjacking feature. Please see the sections
programming features and transmitters. describing these features.
Page - 3 Page - 4

Downloaded from www.Manualslib.com manuals search engine

 protection will be reinstated for the affected circuit if its normal state is restored. For
Arming The Security System example, if the trunk is left open, you can still arm the system normally from the transmitter.
"Arming" your security system, or placing it into a state whereby an intrusion attempt The bypassed circuit will automatically be reinstated for protection three seconds after that
will activate it, may be done by two methods. First, the transmitter may be used to "actively" circuit becomes operative, i.e., the trunk is closed. When a circuit is in a bypassed state, all
arm the system, provided the ignition switch is "off" and the system is not in Valet Mode. other operating circuits will be protected normally. If desired, the system may be
Second, an automatic method of "passively" arming the security system is Last Door programmed so that an open door will also produce this three siren chirp and light flash
Arming. This method may be selectively programmed to operate or not operate, and if warning.
utilized, it will operate in conjunction with Active Arming.
Auxiliary Sensor Bypass: When actively arming the security system, the auxiliary
sensor, if present, may be bypassed if desired. After arming the system, within five seconds
Active Arming The Security System Using The Transmitter: The security
of hearing the arming confirmation chirp, press the small transmitter button. You will hear
system can always be armed with the transmitter if the ignition switch is “off” and the system
another siren chirp confirming the security system has armed without the sensor circuit
is not in the Valet Mode. To arm the system after you exit the vehicle and close all doors,
protecting the vehicle. The next time you arm the security system, the system will reset to
simply press the large transmitter button once. The parking lights will flash once, the siren
its normal condition, and the sensor will again be part of your protection.
will chirp once, and the LED Status Light will begin flashing, confirming that the system
is arming. Provided the optional doorlock interface was installed, the doors will also lock
upon arming, and the optional starter interrupt relay will prevent any attempt to start the Passively Arming The Security System With The Last Door Arming
vehicle. Three seconds after the siren chirp the system becomes fully armed, and will Feature: The security system can be programmed to arm itself automatically when the
activate if an intrusion attempt is detected. vehicle's last door is closed. The moment the last door closes the system begins a countdown.
Once the countdown begins the system will give one chirp and the parking lights will flash
Arming Bypass: Upon active arming, if the hood/trunk circuit or shock sensor is in a once, confirming that all points of entry are closed, and the arming process is in progress.
violated state, the system will arm with three siren confirmation chirps and three parking This period is indicated by a fast-flashing LED Status Light. Thirty seconds after the last
light flashes to alert you. When this occurs, protection for that circuit will be bypassed, but door was closed, the siren will chirp again, the parking lights will flash once, and the LED
Page - 5 Page - 6
Status Light will flash slow three seconds later, confirming that the alarm is fully armed. If
a point of entry is reopened before the single chirp and parking flash, the Last Door Arming Security System Armed And Activated
will be suspended until the point of entry is reclosed. When the 30 second siren chirp occurs
the alarm will become armed; the doors will lock if the door lock interface is installed and While the security system is in an armed state, the LED Status Light will be flashing. In
the "Doors Lock With Last Door Arming and Automatic Rearming" feature is turned on, and this mode, any entry or optional sensor violation will instantly activate the system. Once
the optional starter disable engages. Three seconds later the LED Status Light will flash activated, the following actions will occur:
slow, confirming that the alarm is now fully armed. The "Last Door Arming" feature offers 1) The electronic siren will start sounding, and every 5 seconds the siren will change
a high level of security, since you do not have to remember to arm the alarm system each its sound to generate more attention to the vehicle.
time you exit your vehicle. In addition, Last Door arming may entitle you to an insurance 2) The exterior lights will flash during the activation period.
discount. 3) If configured, the doors will relock. This feature is so unique to this security system
that it even knows when a door is opened and, if so, the system waits until the door
Please note the following parameters of the Last Door Arming feature: is closed before relocking them, so that the thief cannot easily regain entry.
The siren and lights will stay active for 60 seconds before automatically resetting, unless
- Arming Bypass does not operate with the Last Door Arming feature. This bypass feature you disarm the system with the transmitter or Valet Switch and ignition key. If all protected
only operates when arming from the transmitter because all protected entries must be entries are secure at the end of the 60 seconds, the system will stop and rearm automatically
closed for the Last Door Arming countdown to start. to detect, and respond to, another entry attempt. If there is a protected entry still open, or a
sensor still in a triggered state at the end of 60 seconds, the system will reactivate for two
- To prevent the security system from Last Door Arming while vehicle is being refueled or more 60 second cycles. The system will stop after a total of 3 minutes and rearm
at other times automatic arming is not desired, you should put the system in Valet Mode automatically, while ignoring only the open entry or triggered circuit. When the entry is
or you may keep your door open. Leaving the ignition switch "on" is not recommended. closed, protection will instantly be reinstated for that circuit.
After the security system is triggered, the disarm confirmation will no longer be 2 chirps,
- You can still arm the alarm instantly from the transmitter at anytime during the 30 second and the exterior lights staying on for 30 seconds. Instead, the system will respond by
Last Door Arming countdown. producing 4 siren chirps and flashing the lights 4 times before the lights stay on for 30
Page - 7
Page - 8

Downloaded from www.Manualslib.com manuals search engine

 seconds. The LED Status Light will change to flashing one to five times between pauses, Safety Disarm/Storm Mode: While the system is activated, i.e. sounding the siren
which indicates which protected zone triggered the system. The LED Status Light will and flashing the lights, pressing the large transmitter button will disarm the system only.
continue flashing this violation code until the ignition key is turned “on”, thus clearing the The system will not chirp twice or illuminate the parking lights, nor unlock the doors
system's LED Status Light memory circuit. If desired, the system may be programmed for if the system is configured to also operate the door locks. This safety feature ensures that
30 second activation cycles instead of 60 second activated cycles. the vehicle remain secure should the system require disarming due to being activated from
nuisance or malicious sensory inputs. To remotely unlock the doors if the system is
disarmed while activated, repeat the arm/disarm operation by pressing and releasing the
Disarming The Security System large transmitter button once, then again. If disarmed from a panic mode, the normal disarm
indications are present, including the unlocking of the doors.
While the security system is in the armed condition, pressing the large transmitter button
once will instantly disarm the system and unlock the doors, provided an optional interface Automatic Rearming: On occasion people have accidentally disarmed their security
was installed. Disarming is confirmed by the siren chirping twice and the parking lights system by playing with the transmitter or by unknowingly transmitting from a purse or
turning on for 30 seconds to illuminate the way to your car, except under the following pocket. To prevent accidental disarming, if the Automatic Rearming Feature is utilized, the
conditions: first, the parking lights will turn off 10 seconds after a door is opened, and system will automatically rearm itself 90 seconds after disarming, unless the ignition switch
second, the parking lights turn off instantly when the ignition is turned "on". is turned "on". If the "Doors Lock With Automatic Rearming" Programmable Feature is
However, if the security system was activated and reset while you are away, the disarm utilized, the doors will also lock when the system automatically rearms. Automatic
confirmation will change to 4 siren chirps, 4 parking light flashes, and then the parking lights Rearming is indicated by a fast flashing LED Status Light. Once the ignition switch is turned
will stay on for 30 seconds. The alarm will have this response upon every disarming until "on", the system will stay in the disarmed condition until you are ready to arm the system
the ignition switch is turned "on", which will clear the LED Status Light memory. again from the transmitter or from the Last Door Arming Feature. Opening a door will also
Anytime the security system activates, the LED Status Light will indicate which cancel Automatic Rearming, although the countdown will resume when the door is shut if
protected zone caused the activation by flashing one to five times between pauses. This code Last Door Arming is on. In this case, while the door is open, the LED Status Light will be
will continue to flash, even after disarming, until it is cleared by turning the ignition switch on steady until the door is shut, upon which time it will resume flashing fast. Regardless
"on". The system can retain up to five violation codes in its memory. of either condition, if the ignition is turned "on", all automatic arming functions will cease.
Page - 9 Page - 10

Whenever the security system is disarmed, simply depress the Easy ValetTM Switch for
Remote Panic two seconds to achieve the Valet Mode, then release. The system will confirm it is in the
In a threatening situation, the transmitter may be used to fully activate the system, Valet Mode with two siren chirps, and the LED Status Light will become constantly
sounding the siren, flashing the parking lights and relocking the doors (if configured with illuminated. The system will hold memory of the Valet Mode condition while the ignition
a doorlock interface). Even if the ignition is on, Remote Panic can be activated by pressing is "on" or "off". While in the Valet Mode, the transmitters can still operate the Panic feature,
and holding the transmitter's large button for two seconds. The system will automatically an optional power doorlock interface, or optional trunk release. Additionally, the doors will
reset after 60 seconds, or the transmitter's large button may be pressed and released again lock when the ignition is turned "on" and unlock when turned "off"', if this programmable
to deactivate the Remote Panic feature. feature is being utilized. Easy ValetTM Mode prevents active (via transmitter) or passive (via
Last Door Arming or Automatic Rearming) arming of the system.

Valet Override - Disarming The Security System Without The Transmitter:

The Valet Switch And Valet Modes In the event the transmitter is lost, damaged, or its batteries become exhausted, the Easy
ValetTM Switch and your ignition key may be used to disarm the system:
The Valet Switch may be used to keep the security system from actively or passively Step 1: With the system in the armed condition, enter via the driver's door (be aware that
arming during extended stopovers at service stations, for maintenance, valet parking, car the alarm will activate when the door is opened).
washing, etc., by placing the system into Valet Mode. There are two forms of Valet Mode: Step 2: Using your key, turn "on" the ignition.
first is Easy ValetTM, whereby a disarmed system may be placed into Valet Mode without Step 3: Within 10 seconds, press and hold the Easy ValetTM Switch and the alarm will disarm
the ignition key, and the second form is Valet Override, which will disarm an armed or instantly.
activated system and requires the use of the ignition key.
Easy ValetTM: This unique feature can be activated anytime the alarm is in the The Easy ValetTM Switch is also part of the programming operations for learning new
disarmed condition. Easy ValetTM is unique because other security systems require the transmitter codes and changing programmable features.
ignition switch to be "on", but with this system, the ignition can be either "on" or "off".
Page - 11 Page - 12

Downloaded from www.Manualslib.com manuals search engine

 5) 1 flash and pause = 1 transmitter code is stored in the system's memory.
The Red LED Status Light 6) 2 flashes and pause = 2 transmitter codes are stored in the system's memory.
The LED Status Light is used as a visual indicator of the different states that the 7) 3 flashes and pause = 3 transmitter codes are stored in the system's memory.
security system can be in at any given time. Additionally, it is also used as part of the 8) 4 flashes and pause = 4 transmitter codes are stored in the system's memory.
Automatic Transmitter Verification, the Zone Violation, and the Zone Testing features.
The Red LED Status Light is normally positioned in a location that is easily observed by Zone Violation: If the system is activated the Red LED Status Light will start to flash
the driver, and these are the possible conditions reflected by the LED Status Light: and pause the #9 through #13 sequences to indicate which protected circuit caused the
activation. This is seen while the system is activated and after disarming. The flash codes
will continue until the ignition switch is turned "on", which will clear the system's
Security System Status: The primary function of the Red LED Status Light is
memory. Five different Zone Violation codes can be stored by the system.
indicate the following normal operating parameters of the security system:
9) 1 flash and pause = System was activated by current sensing.
1) Off = The system is disarmed and not performing any automatic
10) 2 flashes and pause = System was activated from the hood or trunk circuit.
functions.
11) 3 flashes and pause = System was activated from the door circuit.
2) On Constant = The system is in the Valet Mode.
12) 4 flashes and pause = System was activated from the auxiliary input.
3) Flashing Slow = The system is fully Armed.
13) 5 flashes and pause = System was activated from the auxiliary prewarn input.
4) Flashing Fast = The 30 second Last Door Arming or the 90 second Automatic
Rearming features are in progress.
Zone Testing: Every time the ignition key is turned off , the LED Status Light will flash
and pause the #14 through #18 code to indicate if and when a protected circuit, or "zone",
Automatic Transmitter VerificationTM: After the ignition is turned "on", the
is in an activated state. For example: open a door after the ignition is turned off and the Red
LED Status Light will flash to indicate the number of transmitters programmed to operate
LED Status Light will start flashing 3 times and pause until the door is closed. If another
the security system. For example: two flashes and a pause indicates that only two
protected entry point is violated while the door is still open, then the Red LED Status Light
transmitters are coded to operate the system. This feature normally operates for a 10
will alternatively indicate all activated protected zones.
second period every time the ignition switch is turned "on".
Page - 13 Page - 14

14) 1 flash and pause = System is detecting a current draw. 4) One siren chirp, and no light flash, but only at the moment the ignition switch is turned
15) 2 flashes and pause = System is detecting a violated hood or trunk circuit. "off": The alarm is in Valet Mode, and will not arm either actively or passively.
16) 3 flashes and pause = System is detecting a violated door circuit.
17) 4 flashes and pause = System is detecting a violated auxiliary input. 5) Two siren chirps & the lights stay on for 30 seconds: The system has just been disarmed,
18) 5 flashes and pause = System is detecting a violated auxiliary prewarn input. unless disarmed from an activated (triggered) state.

6) Four siren chirps & four light flashes, then the lights stay on for 30 seconds: The system
Siren And Parking Light Confirmation has just disarmed and was activated while you were away. The system will have this
disarming confirmation until the ignition switch is turned "on".
The Security system's electronic siren and the vehicle's parking lights are utilized to
indicate a number of events or processes associated with the system's operation: 7) Two short siren chirps: The system has just entered the Valet Mode.

1) One siren chirp & one light flash: The system has started a passive Last Door Arming 8) Siren sounding, changing sounds every 5 seconds, and lights flashing on and off: The
countdown and will become armed after the 30 second countdown expires. This chirp system is in an activated state.
indicates that the starter interrupt will engage and the doors will lock when the alarm will
become fully armed 30 seconds later. 9) A series of siren chirps lasting two seconds while the system is armed: The Prewarning
feature has been activated.
2) One siren chirp, one light flash, & doors lock (if equipped thusly): The system has armed
passively or actively from the transmitter. The optional starter interrupt has engaged and The FREEDOM-200+P features a Domelight Supervision output which will allow the
doors have locked. The sensory circuits will become operational 3 seconds later. installer to easily configure the vehicle's domelight to illuminate in conjunction with the
parking lights. When utilized, the Domelight Supervision feature will enhance your
3) One siren chirp after the arming chirp above: The shock sensor circuit is bypassed by personal security by allowing the inspection of the interior upon disarming at night. Adding
pressing the small transmitter button within 3 seconds of pressing the large button. the Domelight Supervision feature typically requires an optional relay.
Page - 15 Page - 16

Downloaded from www.Manualslib.com manuals search engine

 Shock Detection And Prewarn Circuit Programmable Features
This system allows the easy addition of an auxiliary sensor which will activate the system The FREEDOM-200+P security system has 16 Programmable Features, that may be
if a shock or impact to the vehicle is detected. Your system is equipped with a Prewarning easily changed through the Features Programming Mode. The Programmable Features, and
feature, which requires connection of an Dual-Zone sensor. When equipped, a minor impact their factory-set default setting, are:
will cause the security system to respond by chirping the siren for two seconds. After this
feature has been activated 5 times it will automatically shut down until the system is rearmed Feature #1: Current Sensing: Default ON.
again. If the vehicle experiences a major impact, a Dual-Zone sensor will fully activate the Feature #2: 3.5 Minute or 3 Second Current Sensing Delay: Default 3.5 minutes.
security system. Feature #3: Last Door Arming: Default OFF.
Feature #4: Doors Lock With Last Door Arming: Default OFF.
Trunk Release And 3rd Channel Output Feature #5: Automatic Rearming: Default OFF.
Feature #6: Doors Lock with Automatic Rearming: Default OFF.
Feature #7: Steady Siren or Pulsed Horn Output: Default Steady Siren.
The FREEDOM-200+P has two additional outputs for enhanced flexibility and conve-
Feature #8: Horn Confirmation Loud or Soft: Default Soft.
nience. The first of these outputs is commonly used for trunk or rear hatch release. This
Feature #9: Doors Lock and Unlock With Ignition On and Off: Default ON.
output is activated by pressing and holding the transmitter's small button for two seconds.
Feature #10: Open Door Bypass For Previous Feature: Default ON.
This operation may also be programmed to automatically disarm the system if it is armed.
Feature #11: 30 or 60 Second Activation Duration: Default 60 Seconds.
The 3rd Channel output is commonly used to activate optional equipment such as remote
Feature #12: Double Unlock Pulse: Default OFF.
car starters. This feature is enhanced especially for remote starting: the when 3rd Channel
Feature #13: Open Door Arming Alert: Default OFF.
is utilized, system will ignore the shock sensor and ignition circuits if it is armed. Further,
Feature #14: Remote Trunk Release Also Disarms Alarm: Default ON.
if any of the other trigger circuits are violated, the system will be activated and the remote
Feature #15: Transmitter Activated Anti-Carjacking: Default OFF.
starter will be turned off, stopping the engine. Also, please see "Transmitter Activated Anti-
Feature #16: Door Activated Anti-Carjacking: Default OFF.
Carjacking" in the Programmable Features section for an explanation of this related feature.
Page - 17 Page - 18

To access Features Programming Mode and change any of the Programmable Features: The 16 Programmable Features explained:

Step #1: Turn "off" the ignition. 1) Current Sensing: (Default ON) When this Feature is on, the system will activate
while armed if a current draw is detected in the vehicle's electrical system. As an example,
Step #2: Within 7 seconds of turning "off" the ignition, press the Valet Switch 5 times. if a vehicle door is opened the system will detect the current draw made by the dome light
illuminating. When programming, at Step #5 in Features Programming Mode press the
Step #3: You have just entered into the Feature Programming Mode. To confirm this, the transmitter's large button to turn this Feature on or press the small button to turn this Feature
siren will respond with a siren burst. For the next 10 seconds the system is ready off.
for you to select what feature you wish to access and turn on or off. The Feature
Programming Mode will deactivate if a selection is not made within 10 seconds. 2) 3.5 Minute/3 Second Current Sensing Delay: (Default 3.5 Minute) This Feature
sets one of two time delays before the Current Sensing Feature will operate after arming the
Step #4: Within 10 seconds of entering the Feature Programming Mode, press the Valet security system. Vehicles having delay dome lights or electric cooling fans may require the
Switch the number of times that equal the feature number you wish to access. After longer setting. When programming, at Step #5 in Features Programming Mode press the
pressing the Valet Switch multiple times the siren will chirp the same number of transmitter's large button to set this Feature for 3.5 minutes or press the small button to set
times to confirm what feature number you are now accessed to for programming. this Feature for 3 seconds.
Example: Press the Valet Switch 5 times and the siren will chirp 5 times.
3) Last Door Arming: (Default OFF) If this Feature is turned on, Last Door Arming
Step #5: To turn on the feature press the large transmitter button. The siren will chirp once will operate. Last Door Arming starts after the ignition switch has been turned "off" and the
to confirm that the feature is turned on. To turn off the feature, press the small last open door is closed. The moment the last door closes the system will chirp the siren,
transmitter button. The siren will chirp twice to confirm the feature is turned off. flash the parking lights once, and begin a countdown (during this countdown the LED Status
Remember, 10 seconds of no programming activity will result in the system Light will be flashing fast). Thirty seconds after the last door was closed, the siren will chirp
automatically exiting the Feature Programming Mode, which is indicated by two again, the parking lights flash once, and the LED will begin to flash slow, confirming that
siren bursts. the security system is fully armed. If a point of entry is reopened before the 30 seconds
Page - 19 Page - 20

Downloaded from www.Manualslib.com manuals search engine

 expires, the countdown stops, and will reset to start again when the door is reclosed. When 6) Doors Lock With Automatic Rearming: (Default OFF) If the previous Feature is
programming, at Step #5 in Features Programming Mode press the transmitter's large button turned on, this Feature determines whether the doors will also lock when the security system
to turn this Feature on or press the small button to turn this Feature off. becomes armed 90 seconds after disarming from Automatic Rearming. When program-
ming, at Step #5 in Features Programming Mode press the transmitter's large button to turn
4) Doors Lock With Last Door Arming: (Default OFF) If this Feature is turned on, and this Feature on or press the small button to turn this Feature off.
the previously explained Last Door Arming Feature is on, the doors will also lock when the
security system becomes armed 30 seconds after shutting the last door. When programming, 7) Steady Siren Or Pulsed Horn Output: (Default Steady Siren) Instead of the
at Step #5 in Features Programming Mode press the transmitter's large button to turn this included electronic siren, if preferred the vehicle's existing horn may be used for the security
Feature on or press the small button to turn this Feature off. system's audible responses. If the vehicle does not utilize an existing horn relay, one must
be added or this output's 1 Amp capacity may be exceeded, which will damage the system's
5) Automatic Rearming: (Default OFF) On occasion, people have accidentally control module. When programming, at Step #5 in Features Programming Mode press the
disarmed their security system by unknowingly pressing the transmitter's button while it is transmitter's large button for the Pulsed Horn output or press the small button to set this
in a purse or pocket. This Feature prevents such accidental disarming. When this Feature Feature for Steady Siren output.
is on, upon disarming the system, a 90 second Automatic Rearming countdown will start.
During this countdown the Status LED will flash rapidly until any point of entry is opened; 8) Horn Confirmation Honk Loud Or Soft: (Default Soft Confirmation Honk) If the
for example, opening the trunk will temporarily suspend the Automatic Rearming process previous Feature is utilized, due to the variety of vehicle horns, the arming and disarming
(steady LED) until reclosed. However, if a door is opened or the ignition switch is turned confirmation honks may adjusted with this Feature. When programming this Feature, at
"on" the Automatic Rearming will be cancelled. At the end of the 90 second period the Step #5 press the large transmitter button to select the Loud Confirmation Horn Honk. Press
system will automatically arm itself, at which time the system will chirp the siren and flash the smaller transmitter button to select the Soft Confirmation Horn Honk.
the parking lights once. Three seconds later, the Status LED will flash slowly, indicating
a fully armed system. The locking of the doors upon rearming is programmed by the next 9) Ignition On / Off To Lock / Unlock Doors: (Default ON) If this Feature is on, the
Feature. When programming, at Step #5 in Features Programming Mode press the doors will automatically lock 2 seconds after the ignition switch is turned "on", and unlock
transmitter's large button to turn this Feature on or press the small button to turn this Feature instantly when the ignition switch is turned "off". When programming, at Step #5 in Features
off. Page - 21 Page - 22

Programming Mode press the transmitter's large button to turn this Feature on or press the 13) Open Door Arming Alert: (Default OFF) If this Feature is utilized, if one of the
small button to turn this Feature off. vehicle's doors is open when the security system is armed via the transmitter, the siren will
chirp 3 times and instead of once and the parking lights will flash 3 times instead of once
10) Open Door Bypass For The Previous Feature: (Default ON) If this Feature is on, upon arming the system. When programming, at Step #5 in Features Programming Mode
the system will check the vehicle's door circuit. If it detects that any of the vehicle's doors press the transmitter's large button to turn this Feature on or press the small button to turn
are open at the time of the ignition being turned "on" or "off", the doors will not this Feature off.
automatically lock when the ignition switch is turned "on", or automatically unlock when
the ignition switch is turned "off". When programming, at Step #5 in Features Programming 14) Disarm System Upon Trunk Release: (Default ON) This Feature adds the con-
Mode press the transmitter's large button to turn this Feature on or press the small button to venience of automatically disarming the security system when the small button is pressed
turn this Feature off. and held to operate remote trunk release. If this Feature is turned off, the trunk release will
still operate, but the system will not disarm. When programming, at Step #5 in Features
11) 30 or 60 Second Activation Duration: (Default 60 Seconds) This Feature selects Programming Mode press the transmitter's large button to turn this Feature on or press the
the length of time that the siren sounds and the parking lights flash when the security system small button to turn this Feature off.
is activated. This Feature is useful where laws or noise ordinances requires shorter siren
times for noise restrictions. When programming, at Step #5 in Features Programming Mode 15) Transmitter Activated Anti-Carjacking: (Default OFF) This Feature adds Anti-
press the small transmitter button to select the 30 second duration time or press the Carjacking protection, which can be activated from the transmitter at any while the ignition
transmitter's large button to select the 60 second duration time. is "on". To activate this Feature, press and hold both transmitter buttons for 3 seconds. The
siren will start chirping 53 seconds later, and for the next seven seconds the Valet Switch
12) Double Unlock Pulse: (Default OFF) This Feature allows the security system to must be pressed once to cancel the Anti-Carjacking Feature. At 60 seconds the siren will
unlock the doors in certain vehicles with some of the newer doorlocking systems. This fully sound, and the parking lights will also flash. At 90 seconds the starter interrupt output
Feature is included for the benefit of the installer, who can determine if it is necessary for will activate. Once the siren sounds and parking lights flash, Anti-Carjacking cannot be
the Double Unlock Pulse Feature to be activated. canceled unless the ignition is turned "off", then back "on"; then the Valet Switch must be
pressed once within 10 seconds of turning the ignition back "on". This is the only way to
Page - 23 Page - 24

Downloaded from www.Manualslib.com manuals search engine

 cancel or turn off the Anti-Carjacking Feature - once activated, the transmitter cannot be 2) Short the two solder dots together. A slotted jeweler's screwdriver works well.
used to cancel or turn off the Feature. When programming, at Step #5 in Features
Programming Mode press the transmitter's large button to turn this Feature on or press the 3) Momentarily shorting the solder dots together for about 5 seconds will result in two
small button to turn this Feature off. siren bursts indicating all 16 Programmable Features are at the factory-set default.

16) Door-Activated Anti-Carjack Protection: (Default OFF) This feature causes the
Anti-Carjacking Feature described previously to be activated by the opening and closing of Encoding Transmitters
the vehicle's door at any time while the ignition switch is "on". This Feature may be used
alone, or in conjunction with the previous Transmitter Activated Anti-Carjacking Feature. Up to 4 different transmitters may be programmed into the security system's memory.
If a door is opened and closed while the ignition switch is "on", the Anti-Carjacking Feature When a new transmitter is encoded into the system, all previous transmitter codes will be
will engage 53 seconds after the door is closed. The Valet Switch must be pressed within deleted. If a third or fourth transmitter is desired, all of the transmitters must be encoded into
60 seconds after the door is shut to cancel the Anti-Carjacking Protection Feature. When system's memory. To program transmitters to operate your system, follow this procedure:
programming, at Step #5 in Features Programming Mode press the transmitter's large button
to turn this Feature on or press the small button to turn this Feature off. 1) Turn "on" the ignition switch.

2) Within 5 seconds of turning "on" the ignition switch, press the Valet Switch 5 times.
Note: The system will respond with a long siren chirp and the Status LED will illuminate
Total System Reset: This procedure resets all 16 Programmable Features to factory- steady, confirming that the system is ready to learn a transmitter code. Turning "off" the
set default positions. The security system's control module must be accessed to perform a ignition automatically terminates the Transmitter Learning Mode, which will be indicated
Total System Reset. Once accessed, follow these steps: by two siren bursts. When the first transmitter code is learned, any and all existing prior
transmitter codes will be erased.
1) Locate the small round hole in the lower control module case. Two solder dots will
be visible beneath this opening.
Page - 25 Page - 26

3) To learn the first transmitter code, press the large transmitter button, (which will arm/
disarm/panic the system), until you hear one siren burst and one short siren chirp to LIMITED LIFETIME WARRANTY
confirm that the code was learned. The Status LED will also start flashing once between Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT, INC. (the Company),
pauses. The other transmitter button functions are automatically learned at this time. are warranted to be free from defects in materials and workmanship under normal use. If a product sold by
the Company proves to be defective, the Company will repair or replace it free of charge within the first year
and thereafter all parts to be repaired will be free with only a nominal charge for Omega Research and
4) To program the second, third or fourth transmitter codes, repeat step 3. As each
Development, Inc.'s labor and return shipping, to the original owner during the lifetime of the car in which
transmitter is learned, the long confirmation chirp will be followed by two short chirps it was originally installed.
for transmitter number two, three short chirps for transmitter number three, and four All products for warranty repair must be sent postage prepaid to Omega Research & Development, Inc.,
short chirps for transmitter number four. An attempt to add any further transmitter P.O. Box 508, Douglasville, Georgia 30133, with bill of sale or other dated proof of purchase. This warranty
codes will be ignored. The Status LED will increase the number of flashes between is nontransferable and does not apply to any product damaged by accident, physical or electrical misuse or
abuse, improper installation, alteration, any use contrary to its intended function, unauthorized service, fire,
pauses as each transmitter is learned. flood, lightning, or other acts of God.
This warranty limits the Company's liability to the repair or replacement of the product. The Company
5) Turning off the ignition switch will automatically remove the system from Transmitter shall not be responsible for removal and/or reinstallation charges, damage to or theft of the vehicle or its
Learning Mode, which is confirmed by two siren bursts. contents, or any incidental or consequential damages caused by any failure or alleged failure of the product
to function properly. Under No Circumstances Should This Warranty, Or The Product Covered By It, Be
Construed As A Guarantee Or Insurance Policy Against Loss. The Company neither assumes nor authorizes
any person or organization to make any Warranties or assume any liability in connection with the sale,
Second Vehicle Operation: The security system can be armed and disarmed from the installation, or use of this product.
combination of pressing both transmitter buttons at the same time. For two vehicle
operation, encode the first vehicle to arm and disarm from the transmitter's large button; this This device complies with FCC Rules part 15. Operation is subject to the following two conditions,
system will have normal operation. Encode the same transmitters to arm and disarm the (1) This device may not cause harmful interference and, (2) This device must accept any interference
that may be received, including interference that may cause undesired operation.
second vehicle from pressing both transmitter buttons. The second vehicle's system will
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
operate from both buttons and trunk release will operate from the small transmitter button. modifications to this equipment. Such modifications could void the user's authority to operate the
Please note that the second vehicle's system will not have the 3rd Channel output function. equipment.
Page - 27 MO_FREEDOM-200+PVER2

Downloaded from www.Manualslib.com manuals search engine