A B C D E F G H I J K A B C D E F G H I J K

Symbol Description Symbol Description

1 1
Two Gang Convenience Outlet Two Gang Convenience Outlet

Two Gang Weather Proof Outlet Two Gang Weather Proof Outlet
WP WP

Two Gang GFCI Outlet Two Gang GFCI Outlet

GFCI 2 GFCI 2
Special Outlet Special Outlet

Two Gang Floor Mounted Outlet Two Gang Floor Mounted Outlet

Panel Board Panel Board

S 4

Power Line S Power Line

PB1

Circuit Home Run ( Indicates circuit

3 Circuit Home Run ( Indicates circuit
3
number and panel board.) number and panel board.) ACU

F Exhaust fan(Wall Mounted)

F Exhaust fan(Wall Mounted)

Switch Line Switch Line

F F
H Heater(Ceiling Mounted) H Heater(Ceiling Mounted)

Lighting Outlet( LED 4 Lighting Outlet( LED 4

Max 50W) Max 50W)

S Single Gang Single Pole Switch S Single Gang Single Pole Switch

S
S2 Two Gang Single Pole Switch S2 Two Gang Single Pole Switch

S3 S3
Three Gang Single Pole Switch Three Gang Single Pole Switch
S 5 5
Notes and Specifications Notes and Specifications
ACU
1. All electrical installation work shall conform to 1. All electrical installation work shall conform to 3
the latest edition of the Philippine Electrical the latest edition of the Philippine Electrical PB1
GFCI

Code, the rules and regulations of local and Code, the rules and regulations of local and
national authorities, and of the local utility national authorities, and of the local utility
companies. companies.
2. Wiring shall be as follows: 2. Wiring shall be as follows:
REF.

a) Main Service Entrance - THHN through exposed S3 a) Main Service Entrance - THHN through exposed
RSC and open overhead. 6 RSC and open overhead. 5 6
b) Raceways for power - THHN through embedded b) Raceways for power - THHN through embedded PB1

PVC pipes after panel board. PVC pipes after panel board.
c) Raceways for lighting - THHN through c) Raceways for lighting - THHN through
embedded PVC pipes after panel board. embedded PVC pipes after panel board.
3. Minimum wire size shall be 2.0mm² for lighting 3. Minimum wire size shall be 2.0mm² for lighting
and 3.5mm² for power outlets. and 3.5mm² for power outlets.
4. Minimum conduit size shall be 15mm ∅ unless 4. Minimum conduit size shall be 15mm ∅ unless
otherwise specified on plans. otherwise specified on plans.
5. Light control switches shall be rated 20A, 230V 5. Light control switches shall be rated 20A, 230V
AC. 7 AC. 7
6. Unless otherwise specified, pull or junction 6. Unless otherwise specified, pull or junction
boxes shall be provided whenever necessary boxes shall be provided whenever necessary
even though such materials are not indicated on even though such materials are not indicated on
the plans. the plans.
7. All branch circuit loads such as lighting 7. All branch circuit loads such as lighting
receptacle and small appliance shall be sized not receptacle and small appliance shall be sized not
more than 80% of the ampacity of the wire. more than 80% of the ampacity of the wire.
8. All materials and equipment shall be brand new 8. All materials and equipment shall be brand new
and of approved type for both location and and of approved type for both location and
purposes.
9. All metal frames shall be properly and
8 purposes.
9. All metal frames shall be properly and
8
adequately grounded. Grounding wire shall be adequately grounded. Grounding wire shall be
provided on all equipment feeders. 1 provided on all equipment feeders.
PB1
10. Mounting heights shall not be less than as 10. Mounting heights shall not be less than as
follows: follows: 2
a) Light switches - 1400mm from FFL a) Light switches - 1400mm from FFL
b) Receptacles - 400mm from FFL S3 b) Receptacles - 400mm from FFL
PB1

c) Telephone/intercom outlets - 400mm from FFL c) Telephone/intercom outlets - 400mm from FFL
WP

d) Panel boards - 1650mm from FFL d) Panel boards - 1650mm from FFL
e) Counter top outlet - 1100mm from FFL e) Counter top outlet - 1100mm from FFL
11. The job shall be executed with quality 9 11. The job shall be executed with quality 9
workmanship, standard tools,and good workmanship, standard tools,and good
engineering practices. engineering practices.
12. Wire color coding are as follows: 12. Wire color coding are as follows:
Hot - Black/Red Hot - Black/Red
Neutral - White/Blue Neutral - White/Blue
Grounding - green with yellow stripes or green Grounding - green with yellow stripes or green
13. Electrical contractors are responsible for the
proper identification and labeling of all circuit
breakers. Each panel will be provided with a
typewritten circuit directory.
LIGHTING LAYOUT 13. Electrical contractors are responsible for the
proper identification and labeling of all circuit
breakers. Each panel will be provided with a
typewritten circuit directory.
POWER LAYOUT
10 10
GROUND FLOOR
14. No revision of design shall be done without the 14. No revision of design shall be done without the
prior knowledge and approval of the designer
and owner.
15. All electrical works shall be done under the
GROUND
SCALE: NTS
FLOOR prior knowledge and approval of the designer
and owner.
15. All electrical works shall be done under the
direct supervision of a duly licensed electrical
engineer or master electrician.
direct supervision of a duly licensed electrical
engineer or master electrician.
SCALE: NTS

PROFESSIONAL ELECTRICAL ENGINEER DRAWN BY SHEET CONTENTS PROJECT TITLE LOCATION PROJECT OWNER SHEET NO. PROFESSIONAL ELECTRICAL ENGINEER DRAWN BY SHEET CONTENTS PROJECT TITLE LOCATION PROJECT OWNER SHEET NO.

REYVIN MYGGS E. GAZO REYVIN MYGGS E. GAZO

PROPOSED PANTUA VILLAGE, ZONE III, E PROPOSED PANTUA VILLAGE, ZONE III, E
Date: 1) LIGHTING LAYOUT GROUND FLOOR REYVIN MYGGS E. GAZO Date: 1) POWER LAYOUT GROUND FLOOR REYVIN MYGGS E. GAZO
PRC No.

PTR No. TIN no.

RESIDENTIAL BUILDING KORONADAL CITY 14 PRC No.

PTR No. TIN no.

RESIDENTIAL BUILDING KORONADAL CITY 14 PRC No.

PTR No.