Products Related to Common Sockets and DIN Tracks

CSM_common_sockets_DS_E_3_5

A Wide Variety of Square and

Round Sockets in Front-mounting
and Back-mounting Models
• Models available with finger protection.
• Hold-down Clips and Socket Bridges for PYF Sockets
are also available.
• New screwless models available.

Models Used with Common Sockets

Sockets
Item Applicable Sockets Item Applicable Sockets
Num- Number
Model Front- Back-
Model ber of Back- Group name of pins
Front-mount- mounting mounting
Group name pins mount-
ing
ing MM2(X)P 8 8PFA
E2C-AM4A 8 P2CF-08 P3G MM3P
Proximi- 11
E2C-AK4A 11 P2CF-11 P3GA MM2(X)KP
ty Sen- E2C MM PL
sors E2C-GE4A MM3XP PFA
8 PYF08A PY MM3(X)KP
E2C-GF4A 14
MM4(X)P
61F-GP-N8 MM4(X)KP
PF083A
61F-APN2
8 G4Q --- 8 8PFA1 PL
61F-UHS 8PFA1
G3F(D) Series
61F-HSL 8PFA G3F PYF PY
G3FM
61F 61F-03B, -04B PL G3H G3H(D) Series
Level 8 PTF PT
61F-GP-N
Devices 11 PF113A G3B G3B(D) Series PF083A PL
61F-GPN-V50
61F-GPN-BT/BC General-
G9H G9H-2@@S PTF PT
purpose
61F-IP Relays and P2R
14 14PFA G2R-1-S@ 5 P2RF-05@
61F-G1P, -G2P Solid-state -05@
Relays G2R
K7L-AT50/AT50D P2R
K7L 8 P2RF-08(-E) --- G2R-2-S@ 8 P2RF-08@
K7L-U/-UD -08@
MY1, MY2 8 P2R
G3R --- 5 P2RF-05@
MY3 11 -05@
MY
PYF PY G7T G7T
(Q, K, H) MY4, MYQ4 5 P7TF-05 ---
MY4Z-CBG 14 G3TA G3TA
MY2K, MY4H G7S-4A2B-E P7S
G7S 14 P7S-14F-END
General- LY1, LY2 8 G7S-3A3B-E -14P-E
purpose LY LY3 11 PT G7SA-3A1B P7SA-10F P7SA
10
Relays PTF G7SA-2A2B P7SA-10F-ND @-10P
and Solid- LY4
14 G7SA G7SA-5A1B
state Re- G7K G7K-412S --- P7SA-14F P7SA
G7SA-4A2B 14
lays P7SA-14F-ND @-14P
G2A, G7SA-3A3B
G2A(K) G2A-434 14 PYF PY P3G
G2AK H3CA-8(H) 8
PL
MK2P 8 PF083A(-E) H3CA
P3GA
MK(K) PL H3CA-A 11
MK3P PL
11 PF113A(-E)
MK2KP H5CN-@M 11 P3GA
Timers H5CN P2CF
Other H5CN
8 P3G
models
H5CX-L8@ 8 P3G
H5CX
H5CX-A11@ 11 P3GA
H5CZ H5CZ-L8@ 8 P3G

1
 Products Related to Common Sockets and DIN Tracks

Item Applicable Sockets Hold-down Clips

Num-
Model ber of Front-mount-
Back- For Square Sockets
Group name pins mount-
ing Sockets
ing PYF@A PY@(QN) PY@-02
PYF08M
H3CR-A8@ Applicable models PTF@A PT@(QN) PT@-0
H3CR-F8@ P3G MY@, MY@N,
8
H3CR-G8@ PL MY@-D, MY2@-CR,
H3CR-H8@ MY4@-CR,
H3CR H3CR-A P2CF MY4Z@-CR,
H3CR-AS MY@-TU, MY2K,
PYC PYC-P
H3CR-AP P3GA MY@N-D2, LY@, PYC-P
11 PYC-P PYC-S
H3CR-F PL LY@N, LY@-TU,
H3CR-FN MYQ@, PYC-A1
H3CR-HRL G3H(D) Series,
G3F(D) Series,
P3G
H3M --- 8 PF085A G3FM, and G9H
Timers PL
MY@I *
H3Y-2 8 --- PYC-P2
H3Y LY@I
H3Y-4 14
PYF PY MY4H --- PYC-P
H3YN-2@ 8
H3YN MY2Z@-CR
H3YN-4@ 14 MY3@-CR Y92H-3 --- PYC-1
H3RN-1@ 5 LY@-CR
P2R
H3RN P2RF-@-E PYC-2
H3RN-2@ 8 @-@7P PYC-3
G2A(K) Series PYC-A2 --- PYC-3
RD2P --- 8 8PFA1 PL PYC-5
PYC-5
P2CF P3G G7K PKC ---
H2C --- 8
PF085A PL
H3Y Y92H-3 --- Y92H-4
H7CX H7CX-A11@ 11 P3GA
Note: The @ in the model number is replaced with 08, 11, or 14.
H7CZ H7CZ-L8@ 8 P3G * If you use a Hold-down Clip with the MY2I, you cannot use the
Counters H7CN-@M 11 P3GA PYF08A.
H7CN Other H7CN Use the PYF14A.
8 P3G
models
E5CC E5CC-@U 11
P2CF
P3GA
For Round Sockets
Tem- E5C2 --- 8 P3G Sockets PF083A PL08 (-Q) PLE08-0
pera- P2CF-11
E5CS-@1, @2 11 P3GA Applicable models PF113A PL11 (-Q) PLE11-0
ture
Control- E5CS Other E5CS
8 P3G
61F-03B, -04B PFC-A1 PLC
lers models 61F-GP-N,
E5L --- 14 PTF14A --- -GPN-BT
PFC-N8 PHC-5
61F-GP-N8
K3FK models not 8PFA (Included
8 ?61F-APN2
Signal listed below with Converter)
MK2P Series, PLC-10 ---
Con- K3FK K3FK-G@ 11PFA ---
verters MK2KP,
K3FK-GS@ 11 (Included with PLC
MK3P@(-US), and
K3FK-SL-?5-@ Converter) PFC-A1
G3B(D) Series
SE SE-KP@N
8PFA1 --- MK3ZP
PLC-1
SAO SAO-@ 8 MK3LP
APR-S PF083A PL08 MYA-NA1, -NB1
Compo- APR MYA-LA1, -LB1
APR-S380/-S440 11 P2CF-11 PL11 PFC-A6 PLC-7 --- ---
nent MYA-NA2, -NB2
Protec- K2CU K2CU-P --- MYA-LA2, -LB2
tive 8 8PFA1
SDV-F@@/-FH@T PL08 MYA-LA12, -LB12 PFC-A7 PLC-8 --- ---
Compo- SDV
nents SDV-D@@ 14 14PFA PL15 APR-S PFC-A6 PLC-7 --- ---
LG2 LG2-@ 8 PF083A PL08 APR-S380/-S440 --- --- --- Y92H-1
PL11 and LG2 PFC-A7 PLC-8 --- ---
K6EL K6EL-@ 11 P2CF-11
P3GA-11
K6EL --- Y92H-1 --- ---
Prod-
ucts for
Note: 1. The 8PFA(1), 11PFA, and 14PFA are held with hooks.
High- 2. The PL15, PL20, and PF202, as well as models not given in
voltage the above table, require panel processing for installation.
Power AGF AGF-1-P5 8 8PFA1 --- 3. The PF085A Hold-down Clip is included with the H3M and
Receiv- H2A. It is an option (sold separately) for the H2C.
ing
Equip-
ment
MYA-NA1, -NB1 8 PF083A
Annun- MYA-NA2, -NB2
MYA MYA-LA1, -LB1 PL
ciators 11 PF113A
MYA-LA2, -LB2
MYA-LA12, -LB12

2
 Products Related to Common Sockets and DIN Tracks
Ordering Information
Square Sockets
Model P2R (back-mounting), pages 11 and 12 P7TF (front-
P2RF (front-mounting), page 9
mounting), page 12
Number of pins Solder terminals PCB terminals
P2RF-05 P2RF-05-E* P2RF-05-S P2R-05A P2R-05P P2R-057P P7TF-05
Approx. 27 g Approx. 38 g Approx. 36 g Approx. 5 g Approx. 5 g Approx. 5.5 g Approx. 28 g

5 pins

P2RF-08 P2RF-08-E* P2RF-08-S P2R-08A P2R-08P P2R-087P ---

Approx. 33 g Approx. 38 g Approx. 40 g Approx. 5 g Approx. 5 g Approx. 5.5 g

8 pins

Note: 1. The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals.
2. To remove the Relay, pull the lever on the Socket with your fingers supporting the lever and the opposite side of the Relay case, and
jiggle the Relay.
* Use a #1 Phillips screwdriver to tighten the screws on this Socket.

Minimum Order Lot The following models are available at the minimum order lot specified below.
Number of pins Model P2RF P2R P7TF Minimum order lot (pcs)
5 pins P2RF-05 P2R-05A P2R-05P P7TF-05
10
8 pins P2RF-08 P2R-08A P2R-08P ---

Model PY (back-mounting), page 15

PYF (front-mounting), page 14
Number
Solder terminals Wrapping terminals PCB terminals
of pins

PYF08A PYF08M PY08 PY08-Y1 PY08QN PY08QN-Y1 PY08-02 *2

Approx. 32 g Approx. 26 g Approx. 8 g PY08-Y3 Approx. 12 g PY08QN2-Y1 Approx. 7.2 g
PY08QN2

8 pins PYF08S
PYF08A-E *1
Approx. 46 g

1 ?

PYF11A PY11 PY11-Y1 PY11QN PY11QN-Y1 PY11-02 *2

Approx. 43 g Approx. 9 g PY11QN2 PY11QN2-Y1

11 pins

PYF14A PYF14T PY14 PY14-Y1 PY14QN PY14QN-Y1 PY14-02 *2

Approx. 49 g Approx. 53 g Approx. 10 g PY14-Y3 Approx. 14 g PY14QN2-Y1
PY14QN2 PY14QN-Y3
PY14QN2-Y3

14 pins PYF14A-E*1
PYF14S
Approx. 62 g

3
 Products Related to Common Sockets and DIN Tracks

Note: 1. The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals.
2. Refer to Models with Standards Certification for detailed information on the models of Common Sockets that are certified for standards.
*1. Use a #1 Phillips screwdriver to tighten the screws on this Socket.
*2. The structure does not resist flux. Manual soldering is recommended for this product.

Model PT (back-mounting), page 18

PTF (front-mounting), page 17
Number
Solder terminals Wrapping terminals PCB terminals
of pins

PTF08A Approx. 47 g PTF08A-E *1 PT08 Approx. 11 g PT08QN PT08-0 *2

Approx. 10.4 g Approx. 8 g
8 pins

PTF11A Approx. 61 g PT11 Approx. 13 g PT11QN PT11-0 *2

Approx. 12.2 g
11 pins

PTF14A Approx. 77 g PTF14A-E *1 PT14 Approx. 17 g PT14QN PT14-0 *2

Approx. Approx. 16.2 g
20 g
14 pins

Note: The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals.
* Use a #1 Phillips screwdriver to tighten the screws on this Socket.
* The structure does not resist flux. Manual soldering is recommended for this product.

Minimum Order Lot The following models are available at the minimum order lot specified below.

Model
Number of pins PYF PY PTF PT Minimum order lot (pcs)

PYF08A
8 pins PY08 PTF08A PT08
PYF08M
10
11 pins PYF11A PY11 PTF11A PT11
14 pins PYF14A PY14 PTF14A PT14

Model Model P7S/P7SA, pages 20 and 21

Number P7LF (front-mounting), page 20
of pins Number
Front-mounting PCB terminals
of pins
P7LF-06 Approx. 60 g
P7SA-10F Approx. 44 g P7SA-10P Approx. 9 g
P7SA-10F-ND Approx. 44 g
6 pins 10 pins

P7S-14F-END Approx. 110 g P7S-14P-E Approx. 25 g

14 pins
P7SA-14F Approx. 59 g P7SA-14P Approx. 10 g
P7SA-14F-ND Approx. 59 g

Note: Refer to Models with Standards Certification for detailed information on the models of Common Sockets that are certified for standards.

4
 Products Related to Common Sockets and DIN Tracks

Round Sockets
Model PL (back-mounting), page 26
PF (front-mounting), P2CF (front-mounting), PFA (front-mounting), P3G (back-mounting),
Number page 22 page 23 page 24 page 25 Solder Wrapping PCB
of pins terminals terminals terminals
PF083A P2CF-08 8PFA P3G-08 PL08 PL08-Q PLE08-0
Approx. 34 g Approx. 55 g Approx. Approx. 40g Approx. 14 g Approx. 15 g Approx.
57 g 10.6g

PF083A-E *

P2CF-08-E
8 pins 8PFA1
Note: The Y92A-48G
Approx. Terminal Cover
66 g can be used to
PF085A provide finger
Approx. 40 g protection.

PF113A P2CF-11 11PFA P3GA-11 PL11 PL11-Q PLE11-0

Approx. Approx. Approx. 74 g Approx. Approx. 15 g Approx. Approx.
47 g 70g 47 g 18.5A 10.8 g

11 pins
PF113A-E * P2CF-11-E Note: The Y92A-48G
Terminal Cover
can be used to
provide finger
protection.

14PFA Approx. 104 g PL15

Approx. 28 g

14 pins --- --- --- --- ---

PL20
Approx. 17 g

20 pins --- --- --- --- --- ---

Note: The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals.
* Use a #1 Phillips screwdriver to tighten the screws on this Socket.

Minimum Order Lot The following models are available at the minimum order lot specified below.

Number of
pins
Model PF P2CF PFA P3G PL
8 pins PF083A, PF085A P2CF-08, P2CF-08-E 8PFA. 8PFA1 P3G-08 PL08
11 pins PF113A P2CF-11, P2CF-11-E 11PFA P3GA-11 PL11
14 pins --- --- 14PFA --- PL15
Minimum order lot
20 10 20 10
(pcs)

Terminal Cover
Model Y92A-48G

Appearance

Note: Refer to Models with Standards Certification for detailed information on the models of Common Sockets that are certified for standards.

5
 Products Related to Common Sockets and DIN Tracks

Hold-down Clips (Unit: mm)

For Square Sockets
PKC One Set (2 Clips) PTC-1 PYC-A1 Approx. 0.54 g PYC-A2 PYC-E1 PYC-P Approx. 1.4 g
4.5 5 One Set (2 Clips) One Set (2 Clips) One Set (2 Clips)
3
5 max.
3.3 5 max. 5 max.
10 5

29 29 max. Approx. 3
7°
71.8 42.8 36.3
36.3

2.7 2.7 38.5

36.3 40.7
4.5
4.5 ±0.1 4.3
3 1 4.5 1.2 4.5 5.8 1.2
4.5 4.5 1.2
2.5 9.6

PYC-P2 Approx. 1.2 g PYC-S Approx. 1.8 g PYC-1 Approx. 6 g PYC-2 PYC-3 PYC-5

9.4
10 8 5 10
8
28
28 28.8 Approx. 3
28 29.5
3.7
2.5

52 58.2 44.5 41.7

PYC Approx. 0.2 g Y92H-1 Y92H-3 Y92H-4

One Set (2 Clips) R9
5 max.
6 3 5
10
3.5 30.5
24.5 2.5
3.7
53
1.5 72.9 20 (84°)
34.5
1.5
34.7
23.5
6 33.7
6 2 4.5
10 4.5 1.2

For Round Sockets

PFC-A1 Approx. 2.2 g PFC-A6 Approx. 2.4 g PFC-A7 Approx. 3.0 g PLC Approx. 2.4 g PLC-1 Approx. 2.6 g PLC-7 Approx. 3.0 g
One Set (2 Clips) One Set (2 Clips) One Set (2 Clips) One Set (2 Clips) One Set (2 Clips) One Set (2 Clips)

4.6 4.6
4.6

69.2 65.7
60.8 73.3 56.6 56.3
62 74.5 94
95.2

7.6 8
8
6 4.5
6 4.5 9
6 4.5

PLC-8 Approx. 6.4 g PLC-10 Approx. 2.0 g PLC-12 Approx. 5.4 g

One Set (2 Clips) One Set (2 Clips) One Set (2 Clips) Minimum Order Lot
5 The following models are available at the
minimum order lot specified below.
Minimum
Type Model order lot
90.2 86.7 (pcs)
64.3
66.2 PYC-A1
100
PYC-P
PYC-A2
For Square PYC-S
8 8 Sockets PYC-1
10
9 6 PYC-2
PYC-3
PYC-5
PFC-A1
For Round PFC-A6
20
Sockets PFC-A7
PLC

6
 Products Related to Common Sockets and DIN Tracks
Specifications
Socket Characteristics
Continuous Insulation
Model Dielectric strength Remarks
carry current resistance*1
Between contact terminals of same polarity: 1,000 VAC for 1 min
P2RF-05(-E)(-S) 10 A 1,000 MΩ min.
Between coil and contact terminals: 4,000 VAC for 1 min
Between contact terminals of different polarity: 3,000 VAC for 1 min
P2RF-08(-E)(-S) 5A Between contact terminals of same polarity: 1,000 VAC for 1 min 1,000 MΩ min.
Between coil and contact terminals: 4,000 VAC for 1 min
Between contact terminals of same polarity: 1,000 VAC for 1 min
P2R-05P 10 A 1,000 MΩ min.
Between coil and contact terminals: 4,000 VAC for 1 min
Between contact terminals of different polarity: 3,000 VAC for 1 min
P2R-08P 5A Between contact terminals of same polarity: 1,000 VAC for 1 min 1,000 MΩ min.
Between coil and contact terminals: 4,000 VAC for 1 min
Between contact terminals of same polarity: 1,000 VAC for 1 min
P2R-057P 10 A 1,000 MΩ min.
Between coil and contact terminals: 5,000 VAC for 1 min
Between contact terminals of different polarity: 3,000 VAC for 1 min
P2R-087P 5A Between contact terminals of same polarity: 1,000 VAC for 1 min 1,000 MΩ min.
Between coil and contact terminals: 5,000 VAC for 1 min
Between contact terminals of same polarity: 1,000 VAC for 1 min
P2R-05A 10 A Between ground terminals: 1,500 VAC for 1 min 1,000 MΩ min.
Between coil and contact terminals: 4,000 VAC for 1 min
Between contact terminals of different polarity: 3,000 VAC for 1 min
Between contact terminals of same polarity: 1,000 VAC for 1 min
P2R-08A 5A 1,000 MΩ min.
Between ground terminals: 1,500 VAC for 1 min
Between coil and contact terminals: 4,000 VAC for 1 min
P7TF-05 5A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min.
The continuous carry current of 10
A for the PYF08S is for an
7 A, -S models:
PYF08A(-E)(-S) Between terminals: 2,000 VAC for 1 min 1,000 MΩ min. ambient temperature of 55°C.
10 A
At an ambient temperature of
70°C, the value is 7 A.
PYF11A 5A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min.
3 A, -S models:
PYF14A(-E)(-S) Between terminals: 2,000 VAC for 1 min 1,000 MΩ min.
5A
PY08(-Y1) 7A Between terminals: 1,500 VAC for 1 min 1,000 MΩ min.
PY08QN(-Y1) 7A Between terminals: 1,500 VAC for 1 min 100 MΩ min.
PY08-02 7A Between terminals: 1,500 VAC for 1 min 100 MΩ min.
PY11(-Y1) 5A Between terminals: 1,500 VAC for 1 min 100 MΩ min.
PY11QN(-Y1) 5A Between terminals: 1,500 VAC for 1 min 100 MΩ min.
PY11-02 5A Between terminals: 1,500 VAC for 1 min 100 MΩ min.
PY14(-Y1) 3A Between terminals: 1,500 VAC for 1 min 100 MΩ min.
PY14QN(-Y1) 3A Between terminals: 1,500 VAC for 1 min 100 MΩ min.
PY14-02 3A Between terminals: 1,500 VAC for 1 min 100 MΩ min.
PTF@@A(-E) 10 A Between terminals: 2,000 VAC for 1 min 100 MΩ min.
PT@@ 10 A Between terminals: 2,000 VAC for 1 min 100 MΩ min.
PT@@QN 10 A Between terminals: 2,000 VAC for 1 min 100 MΩ min.
PT@@-0 10 A Between terminals: 2,000 VAC for 1 min 100 MΩ min.
Between contact terminals of different polarity: 2,000 VAC for 1 min
P7LF-06 30 A Between contact terminals of same polarity: 2,000 VAC for 1 min 1,000 MΩ min.
Between coil and contact terminals: 4,000 VAC for 1 min
PF@@@A 5A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min.
P2CF 5A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min.
P3G(A) 6A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min.
8PFA(1) 10 A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min.
11PFA(1) 10 A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min.
PL@(-Q) 10 A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min.
PLE@@-0 10 A Between terminals: 2,000 VAC for 1 min 1,000 MΩ min.
Between contact terminals of same polarity: 1,000 VAC for 1 min
P6D-04P 5A 100 MΩ min.
Between coil and contact terminals: 3,000 VAC for 1 min
Between contact terminals of different polarity: 2,000 VAC for 1 min
P7S-14@-E(ND) 10 A Between contact terminals of same polarity: 1,500 VAC for 1 min 1,000 MΩ min.
Between coil and contact terminals: 2,000 VAC for 1 min

7
 Products Related to Common Sockets and DIN Tracks

Continuous Insulation
Model Dielectric strength Remarks
carry current resistance*1
Between contact terminals of different polarity: 2,500 VAC for 1 min
P7SA-10@ 6 A *2 Between contact terminals of same polarity: 1,500 VAC for 1 min 1,000 MΩ min.
Between coil and contact terminals: 2,500 VAC for 1 min
Between contact terminals of different polarity: 2,500 VAC for 1 min
P7SA-14@ 6 A *2 Between contact terminals of same polarity: 1,500 VAC for 1 min 1,000 MΩ min.
Between coil and contact terminals: 2,500 VAC for 1 min
*1. The insulation resistance was measured with a 500-VDC insulation resistance meter at the same places as those used for measuring the
dielectric strength.
*2. There are restrictions in the current. Refer to the General Catalog for the OMRON Safety Components (Cat. No. Y106) for details.

Safety Precautions
Refer to Common Relay Precautions for general precautions.

8
 Products Related to Common Sockets and DIN Tracks
Dimensions
P2RF (Unit: mm)
Terminal Arrangement/
Dimensions Mounting Hole Dimensions
Internal Connections

P2RF-05 7±0.2 2
(One Pole) 5-M3.5×8
4.2-dia. hole
4 dia.
9.5

4
35.5 30±0.05
71.5 max. 3
4

M3 (M3 x 16)
or 3.2-dia. hole
2
19.5
5 1
4
19.5 max. 30 max. (Top View)
54 max.
(Top View) Note: Track mounting is also possible.
Refer to page 27.

P2RF-05-E (One Pole)

(Finger Protection Structure) 7±0.2

3.2-dia. hole
59 max. 4 (11)
7
(80.9 max.)* 2 (12) 2
5-M3.5×7 48 max.
3 (14)
39.5±0.1

3.5-dia. hole 4
39.5
(A1)
5
85.5 max. M3 or 3.5-dia. hole
35.5 (A2) 1

(Top View)
(Top View)
Note: Figures in parentheses
indicate DIN standard
*When mounted numbers. Note: Track mounting is also possible.
4 16
11.5
on H3RN-1@. Refer to page 27.
61 max.

P2RF-05-S (One Pole)

(Screwless Model) 4
(11)
32.6
27.6
3
18.0 max. (14)
22.6
2
(12)
24.5

---
35.3
91.8 max.
(A1) (A2)
5 1

(Top View)
Note: Figures in parentheses
28.5 (5.3) indicate DIN standard
(2.4)
numbers.
32.6

P2RF-08 7±0.2 2

(Two Poles) 8-M3.5×8 4.2-dia. hole

4 dia. 9.5

6 3 30±0.05
71.5 max. 35.5
5 4 4

M3 (M3 x 16)
or 3.2-dia. hole
7 2
4 19.5 8 1
19.5 max. (Top View)
30 max.
54 max.
(Top View) Note: Track mounting is also possible.
Refer to page 27.

9
 Products Related to Common Sockets and DIN Tracks

P2RF (Unit: mm)

Terminal Arrangement/
Dimensions Mounting Hole Dimensions
Internal Connections

P2RF-08-E
(Two Poles) 6+0.2
−0.1
(21) (11)
6 3
(Finger Protection Structure) (22) (12)
63 max.
7 2 3.2-dia. hole

1.5 (84.9 max.)* 2 5 4 7

2 8-M3×8 48 max. (24) (14)
3 dia.
39.5±0.1

3.5-dia. hole 8 (A1)

39.5 4
(A2) 1
85.5 max. 35.5 M3 or 3.5-dia. hole
(Top View)

Note: Figures in (Top View)

parentheses Note: Track mounting is also possible.
*
When mounted indicate DIN Refer to page 27.
4 16
11.5 on H3RN-2@. standard numbers.
61 max.

P2RF-08-S (Two Poles) 6 3

(21) (11)
(Screwless Model)
5 4
32.6 (24) (14)
18.0 max. 27.6 7 2
22.6 (3.4) (22) (12)

24.5

---
35.3
91.8 max. (A1) (A2)
8 1

(Top View)

Note: Figures in
parentheses
(2.4) 28.6 (5.3) indicate DIN
32.6 standard numbers.

Note: 1. If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is negative.
2. Refer to pages 28 and 30 for the features of Screwless Sockets and for precautions for correct use.

10
 Products Related to Common Sockets and DIN Tracks

P2R (Unit: mm)

Terminal Arrangement/
Dimensions PCB Dimensions
Internal Connections

P2R-05P (One Pole) 4

Five, 1.6-dia. holes
14.5 max. 7.5 3.5
1 3 6
6 4 4.5
4.5 2 15
35.5 max. 1.2 15
3.5
4
1 4
1.5 5 (5)

4 7 7

36.5 max. (Bottom View) (Bottom View)

P2R-08P (Two Poles)

7.5
14.5 max. 7.5 3.5 Eight, 1.3-dia holes

0.3 4 5
5
3 6 5
5 2 7 5
35.5 max. 1
2.8 20
20

1 8
1.5 (4.3)
7.5

36.5 max. (Bottom View) (Bottom View)

P2R-057P (One Pole)

14 max. 16.4 4±0.1
8.7 10.4 3.5 Five, 1.6-dia. holes
0.7 1 1

6 3
6±0.1
4.5 4
29.6 15 4.5±0.1
37 max.
4 2 15±0.1
1 8.75
4±0.1
8.7 7.4 1 (8.75)
5
7±0.1
4 7

41 max. (Bottom View) (Bottom View)

P2R-087P (Two Poles)

14 max. 16.4
7.5 10.4 3.5 7.5
1 Eight, 1.3-dia holes
0.3

5 4 5
5 3 6 5
37 max. 29.1 1 20 5
2 7
8.1 20

8.9 7.4
1 8 (8.1)
7.5

41 max. (Bottom View) (Bottom View)

Note: If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is negative.

11
 Products Related to Common Sockets and DIN Tracks

P2R (Unit: mm)

Terminal Arrangement/
Dimensions Mounting Hole Dimensions
Internal Connections

P2R-05A (One Pole)

7.5 4.5
14.5 max.
1.2
0.3 3
4
6.7
2
35.5 max. 5 16.7
3.8

1 5
Five, 3 x 1.8-dia. holes

13.6±0.1
6
(Bottom View)
36.5 max.

30.5+00.2
P2R-08A (Two Poles)

7.5
14.5 max. 6.5
1.2 4 5
0.3 (Use panel with thickness of
3 6 1.6 to 2.0 mm.)
5
5 2 7
35.5 max.
2.6 20
2.8

1 8
Eight, 3 x 1.2-dia. holes 1.5

7.5
(Bottom View)
36.5 max.

Note: If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is negative.

P7TF (Unit: mm)

Terminal Arrangement/
Dimensions Mounting Hole Dimensions
Internal Connections

12.5±0.2
P7TF-05 M3 or M4*

19 max.

7+0.2
-0
5-M3.5×8
4 62±0.1
3 2

71.5 max. 35.5

1 M3
5 (Top View)
Note: Track mounting is also possible.
4
9
Refer to page 27.
* We recommend that you use washers
12.5±0.2 19.5
(Top View) if you use M3 bolts or screws.
59 max. Washers are not required with M4
bolts or screws.
Note: If an I/O SSR or Indicator Module is used, the polarity of terminal 1 is positive.

12
 Products Related to Common Sockets and DIN Tracks

PYF (Unit: mm)

Terminal
Dimensions Arrangement/Internal Mounting Hole Dimensions
Connections

PYF08A PYF08A-E
Two M3 or M4
(Finger Protection Structure) or 4.5-dia. holes

Two, 4.2 × 5 6+0.2

−0.1 3.4 Two, 4.2 × 5 6+0.2
−0.1 3.4
mounting holes 8-M3×8 mounting holes 8-M3×8
4 1
8 5
59±0.3

72 max. 35.4 72 max. 35.4

12 9
14 13 15±0.2
(Top View)
4 4
(Top View)
4
6 6 Note: Track mounting is also
23 max. 23 max.
16.5 16.5 possible.
30 max. 31 max. Refer to page 27.

PYF08M 8-M3.5×7.5
3 dia.

7±0.2 4 1
3.5-dia. hole
8 5
33.5 max.
12 9
20±0.1 3.5-dia. or M3 hole
14 13
44.5 max. 1.5
18 max. (Top View)
3.5-dia. mounting holes
6.5-dia. countersinking, depth: 11.5

PYF08S 38.2 max.

(Screwless Model) 36.5 max.

12 9
(41) (11)
8 5
(44) (14)
32.6
27.6 4 1
23.2 max. (42) (12)
22.6 (3.4)

24.5 ---

(A2) (A1)
85 max. 35.4 14 13

(Top View)
Note: Figures in
parentheses
indicate DIN
(5) 28.6 (5.3) standard
32.6 numbers.

PYF11A Two, 4.2 × 5 6+0.2

Two M3 or M4
or 4.5-dia. holes
−0.1 3.4
mounting holes
11-M3×8

3 2 1
6 5 4 59±0.3
72 max. 35.4

9 8 7
11 10 22±0.2
4 (Top View)
29.5 max.
6 (Top View) Note: Track mounting is also
16.5 possible.
30 max.
Refer to page 27.

13
 Products Related to Common Sockets and DIN Tracks
PYF (Unit: mm)
Terminal
Dimensions Arrangement/Internal Mounting Hole Dimensions
Connections

PYF14A PYF14A-E
Two M3 or M4
(Finger Protection Structure) or 4.5-dia. holes
Two, 4.2 × 5 6+0.2 Two, 4.2-dia × 5
−0.1 3.4 6+0.2
−0.1 3.4
mounting holes mounting holes
14-M3×8 14-M3×8

59±0.3

72 max. 35.4 72 max. 35.4

22±0.2
(Top View)
4 4 4 3 2 1
6 6 8 7 6 5 Note: Track mounting is also
29.5 max. 29.5 max.
16.5
possible.
16.5
30 max. 31 max. Refer to page 27.

12 11 10 9 2-M4
PYF14T 30
4 14 13
23.5
33 max. 11.5
Two, 4.2-dia × 5 7±0.2
mounting holes 11
(Top View)
59

70 max. 35.5
24.5
(Top View)
17.8 Note: Track mounting is also
possible.
4
14-M3.5×8 Refer to page 27.
17.4 10

PYF14S 36.5 max.

(Screwless Model)
12 11 10 9
(41) (31) (21) (11)

8 7 6 5
(44) (34) (24) (14)
32.6 4 3 2 1
27.6 (42) (32) (22) (12)
31 max. 22.6 (3.4)

24.55 ---

(A2) (A1)
85 max. 35.4
14 13

(Top View)
Note: Figures in
parentheses
indicate DIN
(4.15) 28.6 standard
32.6 numbers.
Note: Refer to pages 28 and 30 for the features of Screwless Sockets and for precautions for correct use.

14
 Products Related to Common Sockets and DIN Tracks

Relay Sockets and Socket Bridges for PYF

Bridges within the Same Socket
Applicabl
Pitch Appearance Dimensions (mm) Model Specifications
e models

PYD-020B@(2P)
Max. carry current: 20 A (18 A at 70°C)
3.2 Ambient operating temperature: -40 to 70°C (with no
icing or condensation)
7 5.6 Ambient operating humidity: 45% to 85% (with no
PYF14A
mm icing or condensation)
7 7 Conductor material: Brass
Conductor surface treatment: Nickel plating
Package qty: 50/bag
PYD-030B@(3P)

3.2

5.6

Note: 1. The @ in the model number is replaced with the insulation color specification code. B: Black, Y: Yellow
2. Specify the number of bags when ordering.

Bridges between Adjacent Sockets

Applicabl
Pitch Appearance Dimensions (mm) Model Specifications
e models

22 40°

PYD-025B@(2P)
Max. carry current: 20 A (18 A at 70°C)
3.3 Ambient operating temperature: -40 to 70°C (with no
5.6
icing or condensation)
22 Ambient operating humidity: 45% to 85% (with no
PYF08A
mm 154
icing or condensation)
40° Conductor material: Brass
22
Conductor surface treatment: Nickel plating
Package qty: 10/bag
PYD-085B@(8P)

3.3
5.6

29 40°

PYD-026B@(2P)
Max. carry current: 20 A (18 A at 70°C)
3.3 Ambient operating temperature: -40 to 70°C (with no
5.6
icing or condensation)
29 Ambient operating humidity: 45% to 85% (with no
PYF14A
mm 203 icing or condensation)
29 40° Conductor material: Brass
Conductor surface treatment: Nickel plating
PYD-086B@(8P) Package qty: 10/bag

3.3
5.6

Note: 1. The @ in the model number is replaced with the insulation color specification code. B: Black, S: Blue, R: Red
2. Specify the number of bags when ordering.

Socket Bridges
Pitch Applicable models Appearance and dimensions (mm) Model Insulation color
19.7 Insulating coating PYDM-08SR Red
PYF08S
mm PYDM-08SB Blue
27.5 PYDM-14SR Red
PYF14S 14
mm 9 PYDM-14SB Blue
14.3 P2RM-SR Red
P2RF-@@-S Pitch
mm Guide: 1.2 dia. P2RM-SB Blue
Note: 1. Use the Socket Bridges for relay coil bridge wiring.
2. Specify the number of bags when ordering.

Safety Precautions
Maximum Carry Current
• The total current of all bridged poles must not exceed the maximum carry current of the Socket Bridge.
• Make sure that the maximum carry current of the relay contacts is also not exceeded for each pole.
• If you use more than one Socket, use End Plates (PFP-M).

15
 Products Related to Common Sockets and DIN Tracks

PY (Unit: mm)
Terminal
Arrangement/
Dimensions Mounting hole and PCB dimensions
Internal
Connections

PY08 *
Eight, 3 x 1.2 ellipses
PY08-Y1 (L = 42 max.)
PY08-Y13 (L = 60 max.) 25.5 max.
29.5 max.
5

*The 2.7 7.7 2.6 25.8±0.2

PY08-Y@ includes
the part outlined by the
20 max. 24 max.
dashed lines above. L
21.4+0.2
0

PY08QN 1 4
1
PY08QN2 *1
29.5 max.
PY08QN-Y1 5
5 8
*2
PY08QN2-Y1 2.7
(20)
25
9 12
*1. The PY08QN(2)-Y1 includes the part 22 max.
41.5 max. 13.2
outlined by the dashed lines above. (36.5 max.)*2 24 max. 13 14
*2. The figures in the parentheses are for 42 max.
the PY08QN2(-Y1). (Bottom View) 5.8
4.1
1.0
PY08-02 12.65
* The structure does not resist flux. Manual 6.35
0.3
soldering is recommended for this product. 6.4
25.5 max.
29.5 max.
4.2 Eight, 1.3-dia holes

2.7 4.3 2
22 max.
16.5 max.

* Eleven, 3 x 1.2 ellipses

PY11
PY11-Y1 25.5 max.
29.5 max.
5

*The PY11-Y1 includes the 2.7 7.7 2.6 25.8±0.2

part outlined by the dashed
lines above. 20 max. 24 max.
42 max.

21.46+0.2
0
PY11QN 1
PY11QN2 *1 1 2 3
29.5 max.
PY11QN-Y1 5
4 5 6
(20)*2
PY11QN2-Y1 2.7 25
22 max. 7 8 9
*1. The PY11QN(2)-Y1 includes the part 41.5 max.
outlined by the dashed lines above. (36.5 max.)*2 24 max.
13.2
42 max. 10 11
*2. The figures in the parentheses are for
the PY11QN2(-Y1). 5.8
(Bottom View)
4.1
1.0
PY11-02
12.65
* The structure does not resist flux. Manual 6.35
soldering is recommended for this product. 0.3
25.5 max. 6.4
29.5 max.
4.2 Eleven, 1.3-dia holes

2.7 4.3 2
22 max.
16.5 max.

16
 Products Related to Common Sockets and DIN Tracks

Terminal
Arrangement/
Dimensions Mounting hole and PCB dimensions
Internal
Connections

* Fourteen, 3 x 1.2 ellipses

PY14
PY14-Y1 (L = 42 max.) 25.5 max.
PY14-Y3 (L = 60 max. ) 5
29.5 max.

25.8±0.2
*
The PY14-Y@ includes 2.7 7.7 2.6
the part outlined by the
dashed lines above. 20 max. 24 max.
L 21.4+0.2
0

PY14QN 1
*1
PY14QN2 29.5 max.
5 1 2 3 4
PY14QN-Y1 (L = 42 max.)
(20)*2
PY14QN2-Y1 (L = 42 max.) 2.7 25 5 6 7 8
22 max.
PY14QN-Y3 (L = 60 max.) 41.5 max.
(36.5 max.)*2 24 max. 9 10 11 12
L
PY14QN2-Y3 (L = 60 max.)
*1. The PY14QN-Y@ and PY14QN2-Y@ include the part outlined 13 14 13.2
by the dashed lines above.
*2. The figures in the parentheses are for the PY14QN2(-Y@). (Bottom View) 4.4

5.8
1.0
PY14-02 4.1
* The structure does not resist flux. Manual
soldering is recommended for this product. 0.3 12.65
25.5 max. 6.35
29.5 max. 6.4
Fourteen
4.2 1.3-dia. holes
2.7 4.3 2
22 max.
16.5 max.

Note: 1. Use a panel with a thickness of 1 to 2 mm when mounting a Socket on it.

2. You can use the PY14-Y1 or PY14QN-Y1 for the MY4 Series, MY4H, MYQ4(Z), or MY2K.
3. You can use the PY14-Y3 or PY14QN-Y3 for H3Y Timers.

PTF (Unit: mm)

Terminal Arrangement/
Dimensions Mounting Hole Dimensions
Internal Connections

PTF08A Two, 4.5 × 6

7±0.2 3.4
mounting holes
8-M3.5×8

78.5 max. 35.4

Two, 4.5 dia. or

M4 mounting holes

2 1
8
28.5 max. 4 3
30 max.

PTF08A-E (Finger Protection Structure) 68±0.3

Two, 4.5 × 6
3.4 6 5
mounting holes 8-M3.5×8
8 7

(Top View) 19±0.2

(Top View)
78.5 max. 35.5

Note: Track mounting is also

possible.
Refer to page 27.
8
28.5 max.
33 max.

17
 Products Related to Common Sockets and DIN Tracks

Terminal Arrangement/
Dimensions Mounting Hole Dimensions
Internal Connections

PTF11A Two, 4.5 × 6 mounting holes

Two, 4.5 × 6 7±0.2 3.4
mounting holes
11-M3.5×8
3 2 1
6 5 4
68±0.3

78.5 max. 35.4

9 8 7
11 10
27.5±0.2
(Top View)
(Top View)
37 max. 8
Note: Track mounting is also possible.
30 max.
Refer to page 27.

PTF14A Two, 4.5 × 6 3.4

7±0.2
mounting holes
14-M3.5×8

78.5 max. 35.4

Two, 4.5 dia. or M4 mounting holes

4 3 2 1
45.5 max. 8 8 7 6 5
30 max.

PTF14A-E (Finger Protection Structure) 68±0.3

Two, 4.5 × 6
7±0.2 3.4
mounting holes 12 11 10 9
14-M3.5×8
14 13

(Top View) 36±0.2

(Top View)
78.5 max. 35.5
Note: Track mounting is also possible.
Refer to page 27.

45.5 max. 8
33 max.

Note: If you use the PTF08A, PTF08A-E, or PT08 with an LY1 Relay, connect the following terminal pairs: 1-2, 3-4, and 5-6 (for usage at 10 A or
higher).
PT (Unit: mm)
Terminal
Arrangement/
Dimensions Mounting hole and PCB dimensions
Internal
Connections

PT08 PT08QN
5 1.5×1.0

0.3 25.5 29.5

1.0 max. max.
25.8±0.2
25.5 29.5
max. max. 9 2.5
2.7 20 1.5 2
35 max. 21.4+0.2
0
2.7 2 24 max. 1 2
24 max.
20.5 max. Eight, 1.7-dia × 3.5 oblong holes
3 4
PT08-0 5 6
*Maintain a sufficient distance from the
2 pattern when using double-sided PCBs. 15.6
7 8 10
• The structure does not resist flux.
Manual soldering is recommended for
this product. (Bottom View) 5.35
0.3 4.6

12.45
29.5 max. 6.45
2 5* 6.5
6.5

1 4.3 3 Eight, 2.5-dia. holes

22 max.
18 max. (±0.1 tolerance)

18
 Products Related to Common Sockets and DIN Tracks

Terminal
Arrangement/
Dimensions Mounting hole and PCB dimensions
Internal
Connections

PT11 PT11QN
0.3
1.5×1.0

Eleven, 1.7-dia × 3.5 holes 1.5 30.6 32

max.
31±0.2

32 9 2.5
30.6 2.7 20 1.0
max.
35 max. 1.2 26.4
26.6+0.3
0
2.7 1.2 26.4 29.5 max.
10 7 4 1
20.5 max. 29.5 max.
8 5 2
PT11-0 *Maintain 12.45
a sufficient distance from the 11 9 6 3
0.3 pattern when using double-sided PCBs. 6.45 4.6
• The structure does not resist flux. Eleven,
Manual soldering is recommended for 2.5-dia. holes
5.2
this product. (Bottom View)
10
21.4
2 5* 32 max. 10

5.8

2.7 4.3 6.2 6.2 5.65

18 max. 29.5 max. (±0.1 tolerance)

PT14 PT14QN
0.3
1.5×1.0
5

Fourteen, 1.7-dia × 3.5 holes

42.5 max.
1.5 41±0.2

42.5 max.
9 2.5
2.7 20 1.0
35 max.
26.5 max. 26.6+0.3
0
2.7 29.5 max. 13 9 5 1
26.5 max.
20.5 max. 29.5 max.
10 6 2
PT14-0 *Maintain 11 7 3 12.45
a sufficient distance from the 4.6
0.3 pattern when using double-sided PCBs. 6.45
• The structure does not resist flux. 14 12 8 4
Manual soldering is recommended for 5.1 5.8
this product.
(Bottom View) 10

31.4 10
42.5 max.
2 5* 10

Fourteen,
2.5-dia. holes
2.7 4.3 6.4
6.4 5.45
17.5 max. 26.5 max.
(±0.1 tolerance)
29.5 max.

Note: Use a panel with a thickness of 1 to 2 mm when mounting a Socket on it.

19
 Products Related to Common Sockets and DIN Tracks

P7LF (Unit: mm)

Terminal Arrangement/
Dimensions Mounting Hole Dimensions
Internal Connections

P7LF-06 Two, M3.5 x 6 (coil side)

51.5 max.

0 1 Two, 4.5 dia. or

M4 mounting holes
Four, M4 × 8
25 5
(contact side)
40±0.1 46 max.
40±0.1
55.5 max.
2 4 6 8

8±0.05 (Top View)

9.2±0.05

P7S (Unit: mm)

Terminal Arrangement/Internal
Dimensions Mounting Hole Dimensions
Connections

P7S-14F-END
Indicator LED
14-M3.0×8

40 max.
33±0.1

41 42
4 43 44
1
7.5 33 Two, 4.0 dia.
24 34 or M3.5
23 62
14 61 33±0.1
13 51
0 52

80 max.

37
17

5 3.1 5.9
90.5 max.
(5)

P7S-14P-E
70.5 max.
28±0.2 G7S-4A2B-E Mounted

23.5 max.

28±0.2
(21)
Two, 6.5 dia., depth: 8 4.2
2.8
(16.9)

G7S-3A3B-E Mounted 14.5 8

57 max.
Fourteen, 6 7 Two,
2.5 dia. 5×7=35 3.6 dia.
13.2

6 7 (15) 4.1
8
5×7=35 16.9
14.5
23.5 max.

20
 Products Related to Common Sockets and DIN Tracks

P7SA (Unit: mm)

Dimensions Terminal Arrangement/Internal Connections Mounting Hole Dimensions

P7SA-10F G7SA-3A1B G7SA-2A2B

P7SA-10F-ND Mounted Mounted
14.5±0.2
Two, 4 dia.
or M3.5
R2 22.5 max.
60.5 max.
10-M 3× 8
44 33 34 44 33 34
9 max. 5

43 43

24 22
80±0.2

72 max. * *
23 21
Indicator
LED
12 12

11 1 0 11 1 0

9 max.
(Top View)
4 dia.
* This display circuit is available only for "-ND" models.
Note: 1. The Socket is shown with the finger
cover removed. Note: Terminals 23-24, 33-34, and 43-44 are normally
2. Only the -ND Sockets have LED open. Terminals 11-12 and 21-22 are normally
closed.
indicators (orange).

P7SA-14F G7SA-5A1B G7SA-4A2B G7SA-3A3B

P7SA-14F-ND Mounted Mounted Mounted
22±0.2
Two, 4 dia.
64 54 64 54 64 54
or M3.5
R2 30 max. 60.5 max.
14-M3×8
63 53 63 53 63 53
9 max. 5

44 34 44 34 44 32

* * *
43 33 43 33 43 31 80±0.2
72 max.
24 12 22 12 22 12
Indicator
LED
23 1 0 11 21 1 0 11 21 1 0 11

9 max. * This display circuit is available only for "-ND" models.

4 dia.
Note: 1. The Socket is shown with the finger Note: Terminals 23-24, 33-34, 43-44, 53-54, and 63-64 are
cover removed. normally open. Terminals 11-12, 21-22, and 31-32 are (Top View)
normally closed.
2. Only the -ND Sockets have LED
indicators (orange).

P7SA-10P G7SA-3A1B Mounted

0.5 50 max. 0.5 0 11 12 33 34
+
15 max. −
1 23 24 43 44 Three, 3.2 dia.
39.9±0.2
24.8±0.2 (for M3 tapping
4.1±0.2 screws)
G7SA-2A2B Mounted
10.16
41.5 max. 0 11 12 33 34
+ 13.97 11.43 Ten,
− (7.14) 1.1 dia. holes
5.08 5.08
1 21 22 43 44
3.5
(11.1) 0.4 (11.1) 0.8
(Bottom View) (Bottom View)
Three, 2.6 dia.
(for M3 tapping screws) Note: Terminals 23-24, 33-34, and 43-44 are
(±0.1 tolerance)
normally open. Terminals 11-12 and 21-
4.1 24.8 22 are normally closed.
39.9

P7SA-14P G7SA-5A1B Mounted

0 11 12 33 34 53 54
0.5 60 max. 0.5
+
−
15 max.
1 23 24 43 44 63 64

G7SA-4A2B Mounted
0 11 12 33 34 53 54 Three, 3.2 dia.
49.9±0.2 (for M3 tapping
+ 24.8±0.2 Fourteen,
41.5 max. − 4.1±0.2 1.1 dia. holes screws)
1 21 22 43 44 63 64
10.16
G7SA-3A3B Mounted
13.97 11.43
0.4 3.5 0 11 12 31 32 53 54 (7.14) 5.08
(11.1) (11.1) 0.8 5.08 5.08 5.08
+
−
Three, 2.6 dia.
(for M3 tapping screws) 1 21 22 43 44 63 64 (Bottom View)
(Bottom View)
4.1 24.8
Note: Terminals 23-24, 33-34, 43-44, 53-54, and 63- (±0.1 tolerance)
49.9 64 are normally open. Terminals 11-12, 21-22,
and 31-32 are normally closed.

21
 Products Related to Common Sockets and DIN Tracks

PF (Unit: mm)
Terminal Arrangement/
Dimensions Mounting Hole Dimensions
Internal Connections

PF083A 4
8-M3.5×7 7±0.2
Two,
4.2 dia. holes

52 max. 35.4

2 1 8 7
4 33 3.5 2
41 max.
21 max.

PF083A-E 8-M3.5×7 7±0.2 4

Two, 4.2-dia
mounting holes
3 4 5 6
Two M4 or 4.5-dia. holes
52 max. 8 25 dia. 35.4 (Top View)

33±0.2
4
23 3.5 2 Note: Track mounting is also
33 possible.
21 max. Refer to page 27.
41 max.

PF085A 4
8-M3.5×7 7±0.2

6 5 4 3
Two,
4.5 dia. holes
58 max. 35.4

7 8 1 2
4 33±0.2 1.1 2
3.5
40 max. (Top View)
21.6 max.

PF113A 11-M3.5×7
4
22 7±0.2

52 max. 35.4

4 2 1 11 10
5 34 4 3.5 2 3 9
43 max. 31 max. Two M4 or 4.5-dia. holes

PF113A-E 11-M3.5×5 7±0.2 4

34±0.2
4
5 6 7 8 Note: Track mounting is also
52 max. 8 35.4 possible.
(Top View)
4.2 Refer to page 27.

4
5.2 3.5
23 5.5
42.8 31 max.
Note: 1. For the PF083A and PF113A, the Socket key slot is on the top. (Applicable model: MK)
2. The structure of @-E models provides finger protection. Round terminals cannot be used. Use forked crimp terminals.

22
 Products Related to Common Sockets and DIN Tracks

P2CF (Unit: mm)

Terminal Arrangement/
Dimensions Mounting Hole Dimensions
Internal Connections

P2CF-08 8-M3.5×7.5
7.8 3 4.5

Two,
4.5 dia. holes

70 max. 35.4

6 5 4 3
4 50 max.
20.3 max.
Two M4 or 4.5-dia. holes

P2CF-08-E 8-M3.5×7.5
7.8 5 4.5
40±0.2

6 5 4 3
3
P2CF-08-E
Two, 7 8 1 2
4.5 dia. holes
Note: Track mounting is also
70 max.
1.3 (Top View) possible.
35.4
Refer to page 27.
10A250VAC
RESISTIVE
7 8 1 2

4 40±0.2 19
50 max.
20.3

21.5 max.

P2CF-11 11-M3.5×7.5
7.8 3 4.5

Two,
4.5 dia. holes

70 max. 35.4

8 7 6 5
50 max.
4
4 31.2 max. Two M4 or 4.5-dia. holes

P2CF-11-E 11-M3.5×7.5 5 4.5 40±0.2

7.8
9 3
8 7 6 5
10 11 1 2
3
P2CF-11-E
Two, Note: Track mounting is also
4 4.5 dia. holes (Top View) possible.
1.2
70 max. 35.4 Refer to page 27.
9 3
10A250VAC
RESISTIVE

10 11 1 2

4 40±0.2 30
50 max. 31.2 max.

23
 Products Related to Common Sockets and DIN Tracks

PFA (Unit: mm)

Terminal Arrangement/
Dimensions Mounting Hole Dimensions
Internal Connections

8PFA
8-M3.5×7 7.8±0.2

Two, 4
4.5 dia. holes

5 4
118
81 max. 35.4
max.

4 40±0.2 6 5 4 3
51 max.
24 max. Two M4 or 4.5-dia. holes

8PFA1 40±0.2
8-M3.5×7 7.8±0.2

7 8 1 2
4 Note: Track mounting is also
Two, (Top View) possible.
4.5 dia. holes
Refer to page 27.
5 4
130
93 max. 35.4
max.

4 40±0.2
51 max.
24 max.

11PFA
11-M3.5×7 7.8±0.2

Two, 4
4.5 dia. holes 8 7 6 5
4
5 4
118 Two M4 or 4.5-dia. holes
81 max. 35.4
max.

40±0.2
9 3
10 11 1 2
Note: Track mounting is also
4 40±0.2 (Top View) possible.
51 max. Refer to page 27.
33.5 max.

14PFA
14-M3.5×7 7.8±0.2

4
Two, 7 14 6 5 12 4
4.5 dia. holes
5 4 3 Two, 4.5 dia. or M4 mounting holes
118
81 max. 35.4
max.

60±0.2
8
9 15 10 1 11 2
Note: Track mounting is also
4 60±0.2 (Top View) possible.
72 max. Refer to page 27.
33.5 max.

24
 Products Related to Common Sockets and DIN Tracks

P3G/P3GA (Unit: mm)

Terminal Arrangement/
Dimensions Mounting Hole Dimensions
Internal Connections

P3G-08 27 dia.

3 4 5 6

45
---
2 1 8 7
Eight,
45 4.9 17 M3.5 SEMS screws (Bottom View)
Note: The Y92A-48G Terminal Cover can be used to
implement finger protection.

P3GA-11 27 dia.

5 6 7 8
4
45 25.6
3 9 ---
2 1 11 10
Eleven,
45 4.5 6.2 M3.5 SEMS screws (Bottom View)
16.3

Note: The Y92A-48G Terminal Cover can be used to

implement finger protection.

Terminal Cover (Unit: mm)

Appearance Dimensions

Y92A-48G Twelve, 6.4 dia.

34 Y92A-48G
UP
47.7 × 47.7 48 × 48

P C

16.5
24.6 27.6

47.4

Release Lever (Unit: mm)

Applicable models Appearance Dimensions Model

16

PYF08S PYCM-08S
54.4

32.7

28

PYF14S PYCM-14S
52.5

29.6

16.8
P2RF-05-S
40.35
P2CM-S

P2RF-08-S 36

25
 Products Related to Common Sockets and DIN Tracks

PL (Unit: mm)
Terminal Arrangement/
Dimensions Mounting hole and PCB dimensions (bottom view)
Internal Connections
Two, 3.5 dia. or M3 L = 40 mm
PL08 device mounting holes
MK2(Z)P
3.5
4 1 Two, 3.5 or M3 L = 74 mm
Socket mounting holes
Two, PU, AMD-S, MM2(X)P, CZ, STP, H3L,
2 dia. holes TDS, DTS, DSP, TDF, TDV
L = 86 mm
31-dia. hole 61F-GP/-APN, G4Q-212S, RD2P,
50.5 max.40 30 dia. 40±0.3 L
RDA, TDA, AGF, SE, SAD, K2CU,
3.9 SDV-F

Approx.
50.5 max. 20.5

PL08-Q 3.5 4 1 4 5 Two 3.5-dia. or

t0.6×1.3 3 6 two M3 Socket mounting holes

2 7
51 max. 40 30 dia. 1 8 MK2(Z)P
31-dia. hole
40±0.3
16
(Bottom View)

35 max. 35 max.

PLE08-0 15 Two 3.5-dia.

14 Hold-down Clip mounting holes
t0.3
45°
40+0.1
29±0.1 dia. 27.7±0.5 dia.
0
MK2(Z)P

Eight, 2.5-dia. holes

21.5 max.

PL11 3.5 4 1
Two 2-dia.
holes

51 max. 40 30 dia. Two, 3.5 dia. or M3 device mounting

3.9 /Hold-down Clip mounting holes
L = 40 mm L = 74 mm
Two, 3.5 dia. or M3
Socket mounting holes
MK3P MM3P
Approx. MK2KP MK2(X)KP
35 max. 20.5

31-dia. hole
PL11-Q 3.5 4 1 40±0.3 L
L = 42 mm
5 6 7
MK3ZP
t0.6×1.3 4 8
MK3LP
3 9
51 max. 2 10
1 11
16
(Bottom View)
35 max. 35 max.

Two, 3.5-dia. holes

PLE11-0 14 15 Applicable model/Hold-down Clip mounting holes
t0.3 360°
11 L = 40 mm L = 42 mm
MK3P MK3ZP
29±0.1 dia. 28.7±0.5 L MK2KP MK3LP

22 max.
Eleven, 2.5-dia. holes

4
PL15 4 1
Two, 3.5 dia. or M3
device mounting holes

MM3XP
Two 2-dia. MM4(X)P
Two, 3.5 dia. or M3
holes
2 3 4 Socket mounting holes MM3(X)KP
12
66 max. 53 41 max. 1 11 5 4.2-dia. hole MM4(X)KP
13 74
3.9 10 15 6
14
9 8 7

(Bottom View)
45 max.
22 max.
53

26
 Products Related to Common Sockets and DIN Tracks

Terminal Arrangement/
Dimensions Mounting hole and PCB dimensions (bottom view)
Internal Connections

PL20 Two, 3.5-dia. holes 4 1

Two, 4.5-dia. Relay
mounting holes

Two, 2 dia. Two, 4-dia.

19 1 Socket mounting
17 18 20 2 3 holes
46.5 max. 31 max. 16 4 33-dia. hole
15 5 56±0.2
3.9
14 6
13 12 10 8 7
11 9
36.5 max.
23 max. (Bottom View) * Relay mounting holes are not
38±0.2 required for the LDNP.

Note: When mounting, pay due attention to the direction of the key groove of applicable Relays.

Accessories for DIN Track Mounting (Order Separately) (Unit: mm)

DIN Tracks
PFP-100N 7.3±0.15
PFP-50N 4.5
35±0.3 27±0.15
Model

15 25 25 25 25 15 (5)*
PFP-100N
1
10 10
1,000 (500)* *
PFP-50N
Dimensions in parentheses are for the PFP-50N.

DIN Track 16

PFP-100N2 4.5
35±0.3 27 24 29.2

Model
15 25 25 25 25 15 1 1.5
10 10 PFP-100N2
1,000

End Plate 10
6.2
PFP-M 1.8
M4×8
panhead
screw 1
50 35.5 35.3
1.8

11.5
Model
10 1.3 PFP-M
M4 screw and washer 4.8

16
Spacer 5 12
PFP-S

34.8
44.3

Model
PFP-S
16.5

Note: 1. Order the above products in multiples of 10.

2. The Tracks conform to DIN standards.

27
 Products Related to Common Sockets and DIN Tracks

Features of Screwless Sockets

Structured for Easy Wiring Complete Wiring in Three Steps
Contact terminal
(common)
Contact terminal
(NO)
Contact terminal
(NC)
Insert a Screwdriver Insert the wire. Remove screwdriver
screwdriver. inserted. to complete wiring.
Release Lever
(sold separately) • A spring holds the wire in place to reduce wiring work by
Coil terminals 30% (according to OMRON comparison) and eliminates the
Nameplate need to manage torque.
(sold separately)
• DIN terminal numbers also indicated.

Safety Precautions
Precautions for Safe Use
• Do not move the screwdriver up, down, or from side to side or rotate it while it is inserted in the hole. Doing so may damage internal components in the
Socket.

• Do not insert more than one wire into the same hole. Doing so may cause abnormal heating.
• There are two internally connected wiring holes for each terminal.
• Insert the screwdriver along the hole wall as shown below.

Screwdriver
• When you remove a Socket from a support rail, insert the end of a screwdriver into the fixture and move the driver as shown by the arrow in the
following figure.

Screwdriver

Fixture rail

• When you use a Release Lever to remove a Relay from a P2RF-@@-S Socket, insert a screwdriver at the location shown in the following figure
and move the Release Lever in the direction indicated by the arrow to release the lock on the release lever.

28
 Products Related to Common Sockets and DIN Tracks
Precautions for Correct Use
Wiring Tools
Applicable Screwdriver
Use a flat-blade screwdriver with a tip that is 2.5 mm wide (3.0 mm
max.).

2.5 mm (3.0 mm max. )

You cannot use a screwdriver with a thick shaft.

Applicable Screwdriver (Example)
VESSEL No.9900 − (−) 2.5 × 75

Applicable Wires
• You can use either solid wires or stranded wires. Applicable wire
size: 0.2 to 1.5 mm2 (AWG24 to AWG16)
• Strip 8 to 9 mm of insulation from the ends of the wires.

8 to 9 mm

• If you insert stranded wires without ferrules, make sure that the
wires are twisted when you insert them.
• If you use bare ferrules, always attach insulating sleeves.
• If you insert a wire with a sheath outer diameter of 2.2 mm or less,
do not insert the wire far enough so that the sheath is engaged
inside the hole, as shown below.

• Two wires with a sheath outer diameter of 3.2 mm or larger cannot

be inserted for the same terminal at the same time.
• Use heat-shrinking tubes to indicate wire numbers.

29
 Products Related to Common Sockets and DIN Tracks

Wiring

12 11 10 9
Wire insertion holes
41 31 21 11
Screwdriver insertion hole

(1) Insert a screwdriver into a screwdriver insertion hole on the

Socket.

Cross-section A-A Spring

Wire insertion hole

Screwdriver

Screwdriver insertion hole

(2) Press the screwdriver in until it reaches the stopper inside the
Socket. The spring at the back of the wire insertion hole will be
complete open in this condition. The screwdriver will be held in place
even if you remove your hand.

(3) With the screwdriver held in place, insert the wire or ferrule into the
wire insertion hole.

Wire

(4) Remove the screwdriver. The spring will hold the wire. This
concludes the connection procedure.

30
 Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.

Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.

Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.

2017.4
In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2017 All Right Reserved.