Brilliance CT TM

6-slice, 10-slice, 16-slice and 16 Power configurations

Version 1.2

Model: 4535 670 73191, 4535 670 73181, 4535 670 78851, 4535 670 05721

Software Installation Manual

4535 670 87031

Revision A

This document and the information contained in it is proprietary and confidential information of Philips Medical Systems (“Philips”) and may not be
reproduced, copied in whole or in part, adapted, modified, disclosed to others, or disseminated without the prior written permission of the Philips Legal
Department. Use of this document and the information contained in it is strictly reserved for current Philips personnel and Philips customers who have a
current and valid license from Philips for use by the customer’s designated in-house service employee on equipment located at the customer’s designated site.
Use of this document by unauthorized persons is strictly prohibited. Report violation of these requirements to the Philips Legal Department at 22100 Bothell
Everett Highway, Bothell, WA 98021.
This document must be returned to Philips when the user is no longer licensed and in any event upon Philips’ first written request.

Philips Medical Systems © 2004

 Philips Medical Systems
© 2004 KONINKLIJKE PHILIPS ELECTRONICS N. V. ALL RIGHTS RESERVED.

Warranty Disclaimer
PHILIPS PROVIDES THIS DOCUMENT WITHOUT WARRANTY OF ANY KIND, EITHER IMPLIED OR EXPRESSED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.

Limitation of Liability
PHILIPS HAS TAKEN CARE TO ENSURE THE ACCURACY OF THIS DOCUMENT. HOWEVER, PHILIPS ASSUMES
NO LIABILITY FOR ERRORS OR OMISSIONS AND RESERVES THE RIGHT TO MAKE CHANGES WITHOUT
FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. PHILIPS
MAY MAKE IMPROVEMENTS OR CHANGES IN THE PRODUCT(S) OR PROGRAM(S) DESCRIBED IN THIS
DOCUMENT AT ANY TIME.
Symbol Descriptions

Attention symbol Radiation warning symbol

Laser warning symbol Biohazard warning symbol

Magnetism warning symbol Projectile warning symbol

Electrical warning symbol Do not touch

Revision History

ECO # Revision Date Comments

A August 2004 New Release for Version 1.2
Safety Information
To the User of This Manual
The user of this manual is directed to read and carefully review the instructions, warnings and cautions contained herein prior to
beginning installation or service activities. While you may have previously installed or serviced equipment similar to that described in this
manual, changes in design, manufacture or procedure may have occurred which significantly affect the present installation or service.

Installation and Environment

Except for installations requiring certification by the manufacturer per federal standards, see that a radiation protection survey is made
by a qualified expert in accordance with NCRP 102, section 7, as revised or replaced in the future. Perform a survey after every change
in equipment, workload, or operating conditions which might significantly increase the probability of persons receiving more than the
maximum permissible dose equivalent.

Diagnostic Imaging Systems - Mechanical-electrical Warning

All of the moveable assemblies and parts of this equipment should be operated with care and routinely inspected in accordance with the
manufacturer’s recommendations contained in the equipment manuals.
Only properly trained and qualified personnel should be permitted access to any internal parts. Live electrical terminals are deadly; be
sure line disconnects are opened and other appropriate precautions are taken before opening access doors, removing enclosure panels,
or attaching accessories.
Do not under any circumstances, remove the flexible high tension cables from the x-ray tube housing or high tension generator and/or the
access covers from the generator until the main and auxiliary power supplies have been disconnected. Failure to comply with the above
may result in serious or fatal bodily injuries to the operator or those in the area.

Electrical-grounding Instructions
The equipment must be grounded to an earth ground by a separate conductor. The neutral side of the line is not to be considered the
earth ground. On equipment provided with a line cord, the equipment must be connected to properly grounded, three-pin receptacle. Do
not use a three-to-two pin adapter.

Diagnostic Imaging Systems - Radiation Warning

X-ray and Gamma-rays are dangerous to both operator and others in the vicinity unless established safe exposure procedures are strictly
observed.
The useful and scattered beams can produce serious or fatal bodily injuries to any persons in the surrounding area if used by an unskilled
operator. Adequate precautions must always be taken to avoid exposure to the useful beam, as well as to leakage radiation from within
the source housing or to scattered radiation resulting from the passage of radiation through matter.
Those authorized to operate, participate in or supervise the operation of the equipment must be thoroughly familiar and comply
completely with the current established safe exposure factors and procedures described in publications, such as: Subchapter J of Title 21
 of the Code of Federal Regulations, "Diagnostic X-ray Systems and Their Major Components", and the national council on radiation
protection (NCRP) no. 102, "Medical X-ray And Gamma-ray Protection For Energies Up To 10 Mev-equipment Design and Use", as
revised or replaced in the future.
Those responsible for planning of x-ray and gamma-ray equipment installations must be thoroughly familiar and comply completely with
NCRP no. 49, "Structural Shielding Design and Evaluation For Medical Of X-rays and Gamma-rays of Energies Up to 10 Mev", as revised
and replaced in the future. Failure to observe these warnings may cause serious or fatal bodily injuries to the operator or those in the
area.
Add additional safety information as needed
Only qualified and system trained Philips service staff is allowed to perform service (installation, maintenance, quality assurance) on the
Brilliance CT systems. Make sure that the latest version of the service instructions are available. Read the corresponding instructions
TM

carefully prior to working on the system. For your own safety and for more detailed safety information, refer only to the current version of
the documents.
Use only specified tools and auxiliary materials. After finishing any service activity, ensure that all covers of the Brilliance CT, including
TM

the mylar gasket, are closed

Precautionary Measures Regarding Electrical Voltage

Before you start the procedure outlined in this manual, make sure that you read and understand the warnings listed below.

WARNING PRIOR TO ANY SERVICE AND MAINTENANCE ACTIVITIES INSIDE COMPONENTS:

SWITCH OFF THE SYSTEM AT THE MAIN POWER SUPPLY, (USING THE ON-SITE ON-OFF SWITCH)
AND THE INTERNAL/EXTERNAL UNINTERRUPTIBLE POWER SUPPLY (UPS).
MAKE SURE THAT NO OTHER PERSON CAN SWITCH ON POWER OR SWITCH OFF THE SECURITY
MEASURES, WHEN INSTALLATION, MAINTENANCE OR SERVICE WORK ON THE SYSTEM IS
PERFORMED.

WARNING IN ADDITION TO THE WARNINGS LISTED ABOVE, MAKE SURE TO FOLLOW ALL SAFETY
GUIDELINES AS DESCRIBED IN THE SAFETY CHAPTER OF THIS MANUAL. FAILURE TO DO SO
CAN RESULT IN SEVERE PERSONAL INJURY.

CAUTION Always use an ESD protection wrist strap when servicing any component in the system.
 Contents
Host Software Installation for 6, 10, 16-slice configurations .......................................................................... 1-1
Introduction .............................................................................................................................................................................. 1-1
General Information ............................................................................................................................................................ 1-1
Notes about the software being installed............................................................................................................................ 1-2
Installation Notes ................................................................................................................................................................ 1-2
Before Installation .................................................................................................................................................................... 1-3
Host OS Installation ................................................................................................................................................................. 1-9
Host Model CD Installation..................................................................................................................................................... 1-12
Host Applications Installation ................................................................................................................................................. 1-13
Host Utilities Installation ......................................................................................................................................................... 1-15
Host Update CD ..................................................................................................................................................................... 1-16
Operator’s Manual CD Installation ......................................................................................................................................... 1-17

Host Software Installation for 16 Power configuration ................................................................................... 2-1

Introduction .............................................................................................................................................................................. 2-1
General Information ............................................................................................................................................................ 2-1
Notes about the software being installed............................................................................................................................ 2-2
Installation Notes ................................................................................................................................................................ 2-2
Before Installation .................................................................................................................................................................... 2-3
Host OS Installation ................................................................................................................................................................. 2-9
Host Model CD Installation..................................................................................................................................................... 2-12
Host Applications Installation ................................................................................................................................................. 2-13
Host Utilities Installation ......................................................................................................................................................... 2-15
Host Update CD ..................................................................................................................................................................... 2-16
Operator’s Manual CD Installation ......................................................................................................................................... 2-17

Host System Configuration and Registration ................................................................................................. 3-1

olevel_Service Configuration and Registration ........................................................................................................................ 3-1
philips_service Configuration and Registration ........................................................................................................................ 3-3
CT Configuration and Registration........................................................................................................................................... 3-5

I-Box Software Installation .............................................................................................................................. 4-1

Philips Medical Systems Confidential and Proprietary Information i

 Contents
Gantry Controller Boards Software Installation .............................................................................................. 5-1
Reburning Release 2.0 Boot and Application Flash................................................................................................................. 5-1

Optional Equipment Software Installation ...................................................................................................... 6-1

Installation of HP Laserjet 2500 or Lexmark Optra 45 ............................................................................................................. 6-1

CIRS OS Installation ........................................................................................................................................ 7-1

CIRS server hardware ........................................................................................................................................................ 7-1
CIRS operating system installation..................................................................................................................................... 7-1
Monitor, keyboard, mouse .................................................................................................................................................. 7-1
Network connection ............................................................................................................................................................ 7-1
CIRS BIOS Settings ................................................................................................................................................................. 7-2
CIRS Software Installation ....................................................................................................................................................... 7-2
Before Installation ............................................................................................................................................................... 7-3
New Installation using Serial over LAN ......................................................................................................... 7-3
Previously installed systems............................................................................................................................................... 7-4
Installing OS (Windows XP) ..................................................................................................................................................... 7-5
Windows Activation........................................................................................................................................................... 7-10
Activate RAID disk (S1 server only )................................................................................................................................. 7-11

CIRS Application Software Installation ........................................................................................................... 8-1

Remote Desktop Connection to the Server.............................................................................................................................. 8-2
Install Application Software on a Three Server Configuration.................................................................................................. 8-3
Install Application Software on a Two Server Configuration .................................................................................................. 8-11
Install Application Software on a One Server Configuration .................................................................................................. 8-19

System Calibration .......................................................................................................................................... 9-1

Appendix A - Instructions to set Host PC BIOS ............................................................................................. A-1

Appendix B - Re-install Brilliance CT Miscellaneous Component ................................................................. B-1

Appendix C - Server Setup Instructions ......................................................................................................... C-1

Philips Medical Systems Confidential and Proprietary Information ii

 Contents
Appendix D - Update BIOS Setting for CIRS Servers ..................................................................................... D-1
Check BIOS Versions ..............................................................................................................................................................D-1
BIOS Update Instructions.........................................................................................................................................................D-2
S1 Server............................................................................................................................................................................D-2
S2 Server............................................................................................................................................................................D-6
S3 Server..........................................................................................................................................................................D-20
Conclusion ........................................................................................................................................................................D-25

Philips Medical Systems Confidential and Proprietary Information iii

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

Host Software Installation for 6, 10, 16-slice configurations

Introduction
These instructions describe how to install Brilliance 1.2 Software on a 6, 10, and 16-slice configuration system.

WARNING USE EXTREME CAUTION WHEN OPERATING OR WORKING ON EQUIPMENT

WITH COVERS REMOVED. DANGEROUS VOLTAGES ARE EXPOSED WHEN THE
GANTRY COVERS ARE REMOVED. ACCIDENTAL CONTACT WITH THESE
VOLTAGES MAY CAUSE SERIOUS INJURY OR DEATH TO SERVICE PERSONNEL.

General Information
NOTE Read and understand this document in its entirety before proceeding. If you do not understand this
document, then please call your next level of support.

Philips Medical Systems Confidential and Proprietary Information 1-1

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

Notes about the software being installed

Before installing 1.2 software on a 6, 10, or 16-slice system, please verify that the versions of the CD's match those in
the table below.:

CD Version Part Number

Host OS CD Version Brilliance_CT_OS_1.2.0.9 453567111111
Host Model CD (6-slice) Brilliance_CT_Model_6_1.2.0.4 453567111101
Host Model CD (10-Slice) Brilliance_CT_Model_10_1.2.0.4 453567111211
Host Model CD (16-Slice) Brilliance_CT_Model_16_1.2.0.4 453567111221
Host Applications CD Brilliance_CT_Host_1.2.0.24 453567111121
Host Utilities CD Brilliance_CT_Utilities_1.2.0.21 453567111141
Host Update CD Brilliance_CT_Update_1_1.2.0.2 453567111761
Operator’s Manual CD Brilliance_CT_Operators_Manual_1.2.0.1 453567111161
Firmware CD Brilliance_CT_Firmware_1.2.0.5 453567111151
CIRS OS and Applications CIRS-3.4.1.6 453567111131

Installation Notes
1 The K2000 VISA Key (K2D key) and the Service Key determine the level of utilities activation, philips-level or O-
level.
2 A new options key is required if this is a new installation or if the feature set for a specific customer site has changed.
3 A backup of the existing version of system software, calibration, and six controllers (Ghost, TDP, MDP, Rhost, DMC,
and Couch) in NVRAM to an EOD should be made before installation or update of Release Brilliance CT Software, in
order to recover the system if the installation fails.
4 Calibrations should be restored even if re-running full calibrations after installation.
5 Unless the identical version of software is being installed on the system (such as would happen after a disk failure),
FULL calibrations must be performed after installing this software. See System Calibration for instructions on
performing full calibrations.

Philips Medical Systems Confidential and Proprietary Information 1-2

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

Before Installation
NOTE If the system has been previously installed continue with this section. Otherwise skip to Host OS
Installation on page 1-9.
1 Make sure you are logged in as philips_service.
2 Backup Registry Values:
a Click Start > Run.
b Type regedit and click OK.
c Navigate to HKEY_LOCAL_MACHINE/SOFTWARE/Marconi/Gantry Server.
d Record the value for Rotor-Type __________________.
NOTE This field may not exist. If it does not exist, continue without recording the value.
e Navigate to HKEY_LOCAL_MACHINE/SOFTWARE/Marconi/ Gantry Server/Manual Motion Table ID 107.
f Record the value for Manual Motion SL_RL laser gap in 0.1mm, default: 3159 __________________. To do this,
double-click on the Registry Entry to display the Properties window. On the Properties window, click Decimal to
view the value.
g On the Registry Editor window, click File > Exit.
3 Backup the calibration and configuration files to an EOD disk:
This process will not overwrite previous saved versions of calibration and
configuration data. Calibrations should be backed up even if re-running full
calibrations after installation.
a Insert a formatted EOD into the drive.
b Double-click the Backup/Restore icon on the Desktop.
c Click Browse to choose the location of the backup.
d Choose drive F:
e Click OK.
f Click Start Backup.
g Click OK when complete.
h Click Close on the Log window.
i Click Exit on Backup/Restore window.

Philips Medical Systems Confidential and Proprietary Information 1-3

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

j Click Start > My Computer.

k Navigate to C:\usr\diamond.root\cfg\site.
l Right-click on XrtParams_common.cfg, and select Copy from the popup menu.
m Navigate to F:\backup_<Date>_<Time>\calib\c%usr%diamond.root%cfg%site where the Date and Time
correspond to the backup just created. For example, backup_26_Aug_2004_09_23_03.
n Right-click in the window, and select Paste from the pop-up menu.
o Close all windows.
4 Log off of philips_service
5 Log on as olevel_service.
6 Obtain the system identification information:
a On the O-Level Diagnostics Panel, click the Display Network Information button.
b Record the Host Name (Computer name) ____________________
c Record the Hospital LAN Autoconfiguration Enabled: ___Yes ___No
d If Yes, perform Steps i-m. If No, perform Steps e-m.
e Record the Hospital LAN IP address ________________________
f Record the Hospital LAN Subnet Mask ______________________
g Record the Hospital LAN Default Gateway ___________________
h Record the Hospital LAN DNS configurations__________________________________________________
i Under Ethernet Adapter Host-IRS Connection, record the Host-IRS Connection IP address _______________
j Record the Host-IRS Connection Subnet Mask _________________
k Record the Host-IRS Connection Default Gateway ______________
l Record the Host-IRS Connection DNS configurations____________________________________________
m Close the Display Network Information window.
7 On the O-Level Diagnostics Panel, click the Start Scanner Application button.

Philips Medical Systems Confidential and Proprietary Information 1-4

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

8 Archive all Patient Image data to an EOD disk.

WARNING A DIFFERENT EOD DISK MUST BE USED THAN THE ONE USED TO SAVE
CALIBRATIONS AND CONFIGURATION FILES, ABOVE.
a Insert a formatted EOD into the drive.
b Click the Disk button on the Scanner Application to launch the Archive Manager window.
c Make sure Local is selected.
d Select the studies that need to be archived.
e Click File > Copy Images.
f Select EOD and click OK.
g After the images are copied to the EOD, click File > Close on the Archive Manager Window.
9 Obtain the hospital name and default printer from the scanner application:
a Click Home > Utilities > Misc.
b Select Configuration.
c Click on Institution.
d Record Hospital Name ________________________________
_____________________________________
_____________________________________
e Click Cancel.
f Click the Filming button from workflow menu.
g On the Filming window, click File > Printer.
h Record Default printer____________ __________________
i Click Cancel.
j Close the Filming window.

Philips Medical Systems Confidential and Proprietary Information 1-5

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

10 Record the Default Storage Devices from the Scanner Application:

a Click Home > Utilities > Misc.
b Select Default Storage Devices.
c Record the devices selected:

Local ___ CDR ___ Other ________

EOD ___ IRS ___ Other ________

d Click Cancel when done.

11 Obtain the Patient Data options from the Scanner Application:
a Click Home > Utilities > Diagnostic.
b Select Service Parameters.
c Click Patient Data.
d Record Patient Data option information:
Place a check mark next to the corresponding options.

Middle Name ___ Operator's Name ___

Patient's Weight ___ Requesting Department ___
Patient's Height ___ Requesting Procedure ___
Accession Number ___ Comments ___
Other Patient ID ___ Show Scheduled in Tool Bar ___
Patient's Comment ___ Show Catalog in Tool Bar ___
Ethnic Group ___ Display Birth Date as Mandatory ___
Referring Physician's Name ___ Turn On Caps Lock every Start Study ___
Requesting Physician's Name ___ Set Accession Number as first selected field ___

Philips Medical Systems Confidential and Proprietary Information 1-6

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

e On the Configuration Window, click HIS/RIS

f Record HIS/RIS option information:
Place a check mark next to the corresponding options.

FTP enable ___ Pregnancy Status ___

FTP Directory _____________________ (record directory) Protocol Name ___
Accession Number ___ Referenced Patient Sequence ___
Admission ID ___ Referring Physician name ___
Additional Patient History ___ Requesting Physician ___
Confidentiality Constrain on patient data ___ Requested Procedure Comments ___
Contrast Allergies ___ Requested Procedure Description ___
Current Patient Location ___ Requested Procedure ID ___
Ethnic Group ___ Requested Procedure Sequence ___
Imaging Service Request Comments ___ Scheduled Protocol Code Sequence ___
Intended Results Recipients ___ Requesting Service ___
Medical Alerts ___ Scheduled Perform Physician's Name ___
Modality ___ Scheduled Procedure Step Description ___
Other patient IDs ___ Scheduled Procedure Step ID ___
Operator Name ___ Scheduled Procedure Step Start Date ___
Patient's Age ___ Scheduled Procedure Step Start Time ___
Patient's Birth Date ___ Scheduled Procedure Step Location ___
Patient's ID ___ Special Needs ___
Patient's Name ___ Study Description ___
Patient's Sex ___ Station Name ___
Patient State ___ Study Instance UID ___
Patient Comments ___

g Click OK

Philips Medical Systems Confidential and Proprietary Information 1-7

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

12 Backup Bugrep Files

a Insert a formatted EOD into the drive.
b Click Home > Utilities > Service.
c Select Bug Report.
d On the Bug Report window, click Export.
e Select the reports you want to export.
f Click Export to EOD, and then click OK to confirm.
g Click Exit.
13 Click Home, then click Logout on the Scanner Application and answer Yes to the pop-up.
14 Continue with Host OS Installation on the next page.

Philips Medical Systems Confidential and Proprietary Information 1-8

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

Host OS Installation
1 Write down the 25-digit Windows XP product key located on top of the Dell PC. You will use this in a later step.
NOTE The following procedure must be done on the HOST PC, not the CIRS.
2 Unplug the system from the network. This will minimize the chances of getting a virus before the patches are
installed.
3 Remove the EOD from the EOD drive. The system may hang during the installation process if an EOD is in the drive.
4 Insert the OS CD into the CD/DVD ROM drive of the Host PC. The label on this CD is: Brilliance_CT_OS_1.2.0.9
5 Restart the system:
a Click Start > Shutdown.
b On the Shutdown Window, select Restart from the drop-down menu, then click OK.
6 When the Welcome to Philips Medical Systems XP Unattended Install menu appears, press 1 = Begin Installation
to proceed with the installation. This will take approximately 10 min. The system will reboot itself when complete.
NOTE If this menu does not appear on the screen, the BIOS may not be configured properly. See Appendix A
- Instructions to set Host PC BIOS for instructions on configuring the BIOS.
NOTE When the Host restarts after the first reboot, you may see the start screen with a message that says it
is looking for the SCSI device and it timed out. This may happen a few times before the system detects
the SCSI Device. If the system does not find the SCSI device, Power off the Host using the power
button on the PC, wait 10 seconds, then press the button again to power on the Host.
The reason for this is that during a warm reboot, the SCSI device (EOD) may not fully dissipate it’s
charge, and fail to reset. A hard Power Off/Power On should reset the device.
7 When prompted, remove the CD from the drive and restart the computer by pressing <Ctrl><Alt><Delete>. The
system will begin setting up Windows, which will take approximately 17 min.
NOTE The computer may restart several times during this process.
NOTE Do not touch the keyboard or mouse until the Set Computer Name window appears.
NOTE While the Windows Setup Wizard installs files, a Message Box appears asking if you want to restart
your computer for the settings to take effect. DO NOT CLICK ON THIS BOX!
8 When prompted to Set Computer Name, enter the computer name and click OK. If the computer name was recorded
previously in Before Installation then use it.

Philips Medical Systems Confidential and Proprietary Information 1-9

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

9 When notified that the computer name has been changed successfully, click OK.
10 The system will prompt you to Set IP Address. If you do not want to set a Fixed IP Address for the Hospital LAN, click
NO and continue to Step 11, otherwise, click YES and continue with this step.
a Enter the IP Address, Subnet Mask, Default Gateway, Primary DNS, and/or Secondary DNS. Use information
recorded in Before Installation if applicable.
b Click OK when the IP address was changed successfully message box appears.
11 When prompted to Insert the Product Key, enter the 25-digit Product Key located on top of the Dell PC and click OK.
NOTE Leave the Set Proxy boxes blank.
12 Activate Windows.
a On the Activate Windows Dialog, select "Yes, I want to telephone a customer service representative to activate
windows" and click Next.
b Select a location for step 1. Once a location is entered, a phone number will appear in step 2 to call.
c Call this phone number and answer the questions given over the phone. You can use the touch-tone pad on the
phone to enter the number. Provide them with the installation ID.
d Type in the confirmation number in the boxes labeled A-G when they are given to you.
e Click the Next button. When instructed to, click the Finish button.
f The system will restart automatically.
13 After system restart, click OK when notified that the "Windows XP Installation was completed successfully".
14 Configure the Internet Connection Firewall:
a Click Start > Settings > Control Panel.
b Double-click Network Connections.
c Right-click on Hospital LAN, and select Properties from the pop-up menu.
d Click the Advanced tab.
e Set the check boxes so that Internet Connection Firewall is checked and Internet Connection Sharing is not
checked.
f Click Settings.
g Click Add.
h Enter DICOM for Description of service.
i Enter the Host PC name in the Name or IP address field.

Philips Medical Systems Confidential and Proprietary Information 1 - 10

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

j Enter 104 in both External Port Number and Internal Port Number fields for this service.
k Select the TCP radio button.
l Click OK.
m In the Services list, make sure that only DICOM, FTP Server, and Telnet Server are checked. If a Service
Settings window appears, click OK to close the window.
n Click the ICMP tab.
o Make sure that only Allow incoming echo request is checked.
p Close all dialog boxes by clicking OK or Close.
15 Reconnect the network cable.
16 If the system has a dual port network card for the Host-IRS Connection, verify that the Host-IRS Connection is
active.
a On the Host PC Desktop, right-click on My Network Places and select Properties from the pop-up menu.
b If the Host-IRS Connection has an X through it, physically move the network cable to the open port on the network
card.
c Verify the X disappears.
d Close all windows.
17 Drive Letter Correction.
NOTE In certain circumstances, installation of the Brilliance CT 1.2 Software causes the drive letters of the
EOD, CD-R, and CD drives to become mixed up. Check if your drives are defined properly as listed
below.
a Double-click My Computer.
b Check that your drives are defined as shown below:
Drive C: Local Disk (C:)
Drive D: Local Disk (D:)
Drive E: CD/DVD
Drive F: EOD
Drive G: CD-RW
NOTE If the EOD does not appear, power down the Host by pressing the Power Button on the PC. Wait 10
seconds, then press the Power Button again to power up the Host.

Philips Medical Systems Confidential and Proprietary Information 1 - 11

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

c If your drives are defined properly, skip to the Host Model CD Installation section below. Otherwise, continue with
Steps d-h.
d Right-click on My Computer and select Manage. This will open a Computer Management window.
e Select Disk Management.
f Right-click the button for the drive you want to change and select Change Drive Letter and Paths…
g Click Change and select the correct letter, then click OK.
NOTE The system does not allow two drives with the same letter. This means that if you want to exchange the
drive letters of two or more drives, you should give one of the drives an alternate letter temporarily.
h When all the drive letters have been corrected, close the Computer Management window.
18 Continue with Host Model CD Installation.

Host Model CD Installation

1 Make sure you are logged in as Administrator. If continuing from the previous section, you should already be logged
in as Administrator.
2 Host Model CD into the CD/DVD ROM drive of the Host PC.
3 Double-click My Computer.
4 Double-click the E: drive.
5 Double-click Setup.
6 On the Philips Install Supervisor window, click Start.
NOTE No need for password
NOTE Do not touch the keyboard or mouse until install is complete.
7 When the "Installation completed" message appears at the bottom of the Philips Install Supervisor window, ensure
that all the items are Done, (exit code: 0x00000000). Then click Close on the Philips Install Supervisor window.
Also close the Explorer window.
8 Remove the CD.
9 Continue with the next section: Host Applications Installation.

Philips Medical Systems Confidential and Proprietary Information 1 - 12

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

Host Applications Installation

1 Insert the Host Applications CD into the CD/DVD ROM drive of the Host PC.
2 On the Desktop, double-click My Computer. If My Computer does not appear on the Desktop, then click Start > My
Computer.
3 Double-click on the E: drive, then double-click Setup.
4 On the Philips Install Supervisor Utility, enter "install" in the password field, and then click Start. Wait approximately
10 to 15 minutes as the 3rd party software installs.
NOTE Once the Philips Install Supervisor starts installing components, do not touch the keyboard or mouse.
NOTE The system will Reboot during the Installation, and automatically log back in.
5 During installation, the View/Adjust Gantry Registration settings will appear. Select the correct Rotor Type and click
OK.
6 Adjust the date and time if necessary:
NOTE It is critical that the time is set correctly at this point and not modified after the application CD has
been installed. Under certain conditions, modifying the date and time after the application CD has been
installed will result in the option and service keys being corrupted. The only way to correct this
corruption is a full reinstallation.
7 When the "Installation completed" message appears at the bottom of the Philips Install Supervisor window, scroll
through the Install Supervisor and ensure that all the items are Done, (exit code: 0x00000000). Then click Close in
the window.
NOTE If all the items are not "Done, (exit code: 0x00000000)", then go back and reinstall the OS, Model, and
Host Applications software.
8 Remove the CD from the drive.
9 If the system has Dual Monitors, continue with this step. Otherwise, skip to Step 10.
a Right-click on the Desktop and select Properties from the pop-up menu.
b Select the Settings tab.
c Click the Advanced button and select the Quadro4 980 XGL tab. A menu opens on the left.
d Click nView Display Mode.

Philips Medical Systems Confidential and Proprietary Information 1 - 13

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

NOTE If you do not find the nView Display Mode, click Cancel to exit Advanced, select monitor number 2 and
uncheck the 'Extend my windows desktop onto this monitor' button, than click the Apply button. Select
monitor number 1 and go back to step ‘d’.
e In the nView Display Mode area, select the Horizontal span option from the nView Modes drop-down menu.
NOTE If all buttons are grayed out, select monitor number 2 and uncheck the 'Extend my windows desktop
onto this monitor' button, than press Apply button. Select monitor number 1 and try step ‘e’ again.
f Click Apply.
g Click Yes, and then click OK to confirm the settings. The right-hand screen should be activated.
h If the monitors appear swapped, follow Steps i-r. Otherwise, performs Steps n-r.
i click the Advanced button and select the Quadro4 980 XGL tab.
j Click on nView Display2… in the Display pulldown menu.
k Make sure Make this the primary display is checked.
l Click Apply.
NOTE This will change "nView Display2…" to "nView Display1…" and vice versa.
m Click Yes, and then click OK to confirm the settings.
n Make sure that the Screen resolution bar is set to 2560 x 1024.
o Click the Advanced button and select the Monitor tab.
p Verify the Screen Refresh Rate is set to 75Hz. If not, set the rate to 75Hz and click Apply. Otherwise, click OK.
q Click OK on the Display Properties Window.
r Close all open windows.
10 Log out of Administrator:
a Click Start > Shut Down.
b Select Log Off Administrator.
c Click OK.
11 Continue with Host Utilities Installation on the next page.

Philips Medical Systems Confidential and Proprietary Information 1 - 14

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

Host Utilities Installation

1 Login to the Host PC as philips_service (use philips_service password).
NOTE The first time you log into any account, you will see a message popup and then you will be logged out of
the account automatically. Please log back in before continuing.
2 Insert the Host Utilities CD into the CD/DVD ROM drive of the Host PC.
3 Click Start > My Computer.
4 Double-click the E: drive.
5 Double-click Setup.
6 Enter Username and Password.
NOTE Enter philips_service for the Username and enter the philips_service password for the Password.
7 Click the Start Button.
NOTE Do not touch the keyboard or mouse until install is complete, other than to enter the K2000 Visa Entry
when the window appears.
8 Setting the K2D Visa:
a Go to the K2000 Visa Entry window that has been automatically opened.
b Obtain the Machine ID (needed to get the visa key).
c Obtain a visa (the K2D key).
NOTE Either the K2 Visa or the K2000B Visa key can be used when obtaining the key from the web site.
d Enter the visa in the K2000 Visa Entry window, and click Apply.
e Click Done.
NOTE Do not touch the keyboard or mouse at this time. During the installation process the system will
reboot several times.
9 When the "Installation completed" message appears at the bottom of the Philips Install Supervisor window, ensure
that all the items are Done, (exit code: 0x00000000). Then click Close in the Philips Install Supervisor window. Also
close the Windows Explorer window if still open.
10 Remove the CD.

Philips Medical Systems Confidential and Proprietary Information 1 - 15

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

11 CIRS Service Utilities Install:

a Make sure you are logged in as philips_service.
b Click Start > My Computer.
c Navigate to C:\Cirs_temp.
d Double-click on SUtils.vbs.
e If the "user account philips_service already exist" window appears, click OK.
f When the "Service Tools Installation Completed" window appears, click OK.
g Close the Explorer window.
h Continue with the Host Update CD installation below.

Host Update CD
1 Make sure you are logged in as philips_service.
2 Insert the Host Update CD into the CD/DVD ROM drive of the HOST PC.
3 Click Start > My Computer.
4 Double-click the E: drive.
5 Double-click Setup.
6 Click Start.
NOTE No need to change username or password. Wait approximately 5 minutes as the software is installed.
NOTE Do not touch the keyboard or mouse until install is complete.
7 When the "Installation completed" message appears at the bottom of the "Philips Install Supervisor" window, ensure
that all the items are "Done, (exit code: 0x00000000)". Then click "Close" in the "Philips Install Supervisor" window.
Also close the Explorer window.
8 Remove the CD.
9 Continue with Operator’s Manual CD Installation on the next page.

Philips Medical Systems Confidential and Proprietary Information 1 - 16

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 6, 10, 16-slice configurations

Operator’s Manual CD Installation

1 Insert the CD labeled: Brilliance_1CT_OperationsManual_1.2.0.1.
2 Click Start > My Computer.
3 Double-click the E: drive.
4 Double-click Setup.
5 Click Start.
NOTE No need for password. Wait approximately 5 minutes as the software is installed.
NOTE Do not touch the keyboard or mouse until install is complete.
6 When the Installation completed message appears at the bottom of the "Philips Install Supervisor" window, ensure
that all the items are Done, (exit code: 0x00000000). Then click "Close" in the "Philips Install Supervisor" window.
Also close the Windows Explorer window.
7 Remove the CD.
8 Continue with Host System Configuration and Registration on page 3-1.

Philips Medical Systems Confidential and Proprietary Information 1 - 17

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

Host Software Installation for 16 Power configuration

Introduction
These instructions describe how to install Brilliance 1.2 Software on a 16 Power system.

WARNING USE EXTREME CAUTION WHEN OPERATING OR WORKING ON EQUIPMENT

WITH COVERS REMOVED. DANGEROUS VOLTAGES ARE EXPOSED WHEN THE
GANTRY COVERS ARE REMOVED. ACCIDENTAL CONTACT WITH THESE
VOLTAGES MAY CAUSE SERIOUS INJURY OR DEATH TO SERVICE PERSONNEL.

General Information
NOTE Read and understand this document in its entirety before proceeding. If you do not understand this
document, then please call your next level of support.

Philips Medical Systems Confidential and Proprietary Information 2-1

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

Notes about the software being installed

Before installing 1.2 software on a 16 Power system, please verify that the versions of the CD's match those in the table
below.

CD Version Part Number

Host OS CD Version Brilliance_CT_OS_1.2.0.9 453567111111
Host Model CD Brilliance_CT_Model_16P_1.2.0.4 453567111231
Host Applications CD Brilliance_CT_Host_1.2.0.24 453567111121
Host Utilities CD Brilliance_CT_Utilities_1.2.0.21 453567111141
Host Update CD Brilliance_CT_Update_1_1.2.0.2 453567111761
Operator’s Manual CD Brilliance_CT_Operators_Manual_1.2.0.1 453567111161
Firmware CD Brilliance_CT_Firmware_1.2.0.5 453567111151
CIRS OS and Applications CIRS-3.4.1.7 453567111201

Installation Notes
1 The K2000 VISA Key (K2D key) and the Service Key determine the level of utilities activation, philips-level or O-
level.
2 A new options key is required if this is a new installation or if the feature set for a specific customer site has changed.
3 A backup of the existing version of system software, calibration, and six controllers (Ghost, TDP, MDP, Rhost, DMC,
and Couch) in NVRAM to an EOD should be made before installation or update of Release Brilliance CT Software, in
order to recover the system if the installation fails.
4 Calibrations should be restored even if re-running full calibrations after installation.
5 Unless the identical version of software is being installed on the system (such as would happen after a disk failure),
FULL calibrations must be performed after installing this software. See System Calibration for instructions on
performing full calibrations.

Philips Medical Systems Confidential and Proprietary Information 2-2

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

Before Installation
NOTE If the system has been previously installed continue with this section. Otherwise skip to (see Host OS
Installation on page 2-9).
1 Make sure you are logged in as philips_service.
2 Backup Registry Values:
a Click Start > Run.
b Type regedit and click OK.
c Navigate to HKEY_LOCAL_MACHINE/SOFTWARE/Marconi/Gantry Server.
d Record the value for Rotor-Type __________________.
NOTE This field may not exist. If it does not exist, continue without recording the value.
e Navigate to HKEY_LOCAL_MACHINE/SOFTWARE/Marconi/ Gantry Server/Manual Motion Table ID 107.
f Record the value for Manual Motion SL_RL laser gap in 0.1mm, default: 3159 __________________. To do this,
double-click on the Registry Entry to display the Properties window. On the Properties window, click Decimal to
view the value.
g On the Registry Editor window, click File > Exit.
3 Backup the calibration and configuration files to an EOD disk:
This process will not overwrite previous saved versions of calibration and
configuration data. Calibrations should be backed up even if re-running full
calibrations after installation.
a Insert a formatted EOD into the drive.
b Double-click the Backup/Restore icon on the Desktop.
c On the Back/Restore Window, click Browse to choose the location of the backup.
d Choose drive F:
e Click OK.
f Click Start Backup.
g Click OK when complete.
h Click Close on the Log window.
i Click Exit on Backup/Restore window.

Philips Medical Systems Confidential and Proprietary Information 2-3

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

j Click Start > My Computer.

k Navigate to C:\usr\diamond.root\cfg\site.
l Right-click on XrtParams_common.cfg, and select Copy from the popup menu.
m Navigate to F:\backup_<Date>_<Time>\calib\c%usr%diamond.root%cfg%site where the Date and Time
correspond to the backup just created. For example, backup_26_Aug_2004_09_23_03.
n Right-click in the window, and select Paste from the pop-up menu.
o Close all windows.
4 Log off of philips_service
5 Log on as olevel_service.
6 Obtain the system identification information:
a On the O-Level Diagnostics panel, click the Display Network Information button.
b Record the Host Name (Computer name) ____________________
c Record the Hospital LAN Autoconfiguration Enabled: ___Yes ___No
d If Yes, perform Steps i-m. If No, perform Steps e-m.
e Record the Hospital LAN IP address ________________________
f Record the Hospital LAN Subnet Mask ______________________
g Record the Hospital LAN Default Gateway ___________________
h Record the Hospital LAN DNS configurations__________________________________________________
i Under Ethernet Adapter Host-IRS Connection, record the Host-IRS Connection IP address________________
j Record the Host-IRS Connection Subnet Mask _________________
k Record the Host-IRS Connection Default Gateway ______________
l Record the Host-IRS Connection DNS configurations____________________________________________
m Close the Display Network Information Windows.
7 On the O-Level Diagnostics panel, click the Start Scanner Application button.

Philips Medical Systems Confidential and Proprietary Information 2-4

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

8 Archive all Patient Image data to an EOD disk.

WARNING A DIFFERENT EOD DISK MUST BE USED THAN THE ONE USED TO SAVE
CALIBRATIONS AND CONFIGURATION FILES, ABOVE.
a Insert a formatted EOD into the drive.
b Click the Disk button on the Scanner Application to launch the Archive Manager window.
c Make sure Local is selected.
d Select the studies that need to be archived.
e Click File > Copy Images.
f Select EOD and click OK.
g After the images are copied to the EOD, click File > Close on the Archive Manager Window.
9 Obtain the hospital name and default printer from the scanner application:
a Click Home > Utilities > Misc.
b Select Configuration.
c Click on Institution.
d Record Hospital Name ________________________________
_____________________________________
_____________________________________
e Click Cancel.
f Click the Filming button on the workflow menu.
g On the Filming window, click File > Printer.
h Record Default printer____________ __________________
i Click Cancel.
j On the Filming window, click File > Close.

Philips Medical Systems Confidential and Proprietary Information 2-5

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

10 Record the Default Storage Devices from the Scanner Application:

a Click Home > Utilities > Misc.
b Select Default Storage Devices.
c Record the devices selected:

Local ___ CDR ___ Other ________

EOD ___ IRS ___ Other ________

d Click Cancel when done.

11 Obtain the Patient Data options from the Scanner Application:
a Click Home > Utilities > Diagnostic.
b Select Service Parameters.
c Click the Patient Data tab.
d Record Patient Data option information:
Place a check mark next to the corresponding options.

Middle Name ___ Operator's Name ___

Patient's Weight ___ Requesting Department ___
Patient's Height ___ Requesting Procedure ___
Accession Number ___ Comments ___
Other Patient ID ___ Show Scheduled in Tool Bar ___
Patient's Comment ___ Show Catalog in Tool Bar ___
Ethnic Group ___ Display Birth Date as Mandatory ___
Referring Physician's Name ___ Turn On Caps Lock every Start Study ___
Requesting Physician's Name ___ Set Accession Number as first selected field ___

Philips Medical Systems Confidential and Proprietary Information 2-6

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

e Click the HIS/RIS tab.

f Record HIS/RIS option information:
Place a check mark next to the corresponding options, or write them down if you are viewing this on a laptop.

FTP enable ___ Pregnancy Status ___

FTP Directory _____________________ (record directory) Protocol Name ___
Accession Number ___ Referenced Patient Sequence ___
Admission ID ___ Referring Physician name ___
Additional Patient History ___ Requesting Physician ___
Confidentiality Constrain on patient data ___ Requested Procedure Comments ___
Contrast Allergies ___ Requested Procedure Description ___
Current Patient Location ___ Requested Procedure ID ___
Ethnic Group ___ Requested Procedure Sequence ___
Imaging Service Request Comments ___ Scheduled Protocol Code Sequence ___
Intended Results Recipients ___ Requesting Service ___
Medical Alerts ___ Scheduled Perform Physician's Name ___
Modality ___ Scheduled Procedure Step Description ___
Other patient IDs ___ Scheduled Procedure Step ID ___
Operator Name ___ Scheduled Procedure Step Start Date ___
Patient's Age ___ Scheduled Procedure Step Start Time ___
Patient's Birth Date ___ Scheduled Procedure Step Location ___
Patient's ID ___ Special Needs ___
Patient's Name ___ Study Description ___
Patient's Sex ___ Station Name ___
Patient State ___ Study Instance UID ___
Patient Comments ___

g Click OK

Philips Medical Systems Confidential and Proprietary Information 2-7

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

12 Backup Bugrep Files

a Insert a formatted EOD into the drive.
b Click Home > Utilities > Service.
c Select Bug Report.
d On the Bug Report window, click Export.
e Select the reports you want to export.
f Click Export to EOD, and then click OK to confirm.
g Click Exit.
13 Click Home, then Logout on the Scanner Application. Answer Yes to the pop-up.
14 Continue with Host OS Installation on the next page.

Philips Medical Systems Confidential and Proprietary Information 2-8

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

Host OS Installation
NOTE The following procedure must be done on the HOST PC, not the CIRS.
1 Write down the 25-digit Windows XP product key located on top of the Dell PC. You will use this in a later step.
2 Unplug the system from the network. This will minimize the chances of getting a virus before the patches are
installed.
3 Remove the EOD from the EOD drive. The system may hang during the installation process if an EOD is in the drive.
4 Insert the Host OS CD into the CD/DVD ROM drive of the Host PC. The label on this CD is:
Brilliance_CT_OS_1.2.0.9
5 Restart the system:
a Click Start > Shutdown.
b On the Shutdown Window, select Restart from the drop-down menu, then click OK.
6 When the Welcome to Philips Medical Systems XP Unattended Install menu appears, press 1 = Begin Installation
to proceed with the installation. This will take approximately 10 min. The system will reboot itself when complete.
NOTE If this menu does not appear on the screen, the BIOS may not be configured properly. See Appendix A
- Instructions to set Host PC BIOS for instructions on configuring the BIOS.
NOTE When the Host restarts after the first reboot, you may see the start screen with a message that says it
is looking for the SCSI device and it timed out. This may happen a few times before the system detects
the SCSI Device. If the system does not find the SCSI device, Power off the Host using the power
button on the PC, wait 10 seconds, then press the button again to power on the Host.
The reason for this is that during a warm reboot, the SCSI device (EOD) may not fully dissipate it’s
charge, and fail to reset. A hard Power Off/Power On should reset the device.

7 When prompted, remove the CD from the drive and restart the computer by pressing <Ctrl><Alt><Delete>. The
system will begin setting up Windows, which will take approximately 17 min.
NOTE The computer may restart several times during this process.
NOTE Do not touch the keyboard or mouse until the Set Computer Name window appears. Please ignore any
messages asking you to reboot. The system will reboot automatically.
NOTE While the Windows Setup Wizard installs files, a Message Box appears asking if you want to restart
your computer for the settings to take effect. DO NOT CLICK ON THIS BOX!

Philips Medical Systems Confidential and Proprietary Information 2-9

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

8 When prompted to Set Computer Name, enter the computer name and click OK. If the computer name was recorded
previously in Before Installation, then use it.
9 When notified that the computer name has been changed successfully, click OK.
10 The system will prompt you to Set IP Address. If you do not want to set a Fixed IP Address for the Hospital LAN, click
NO and continue to Step 11. Otherwise, click YES and continue with this step.
a Enter the IP Address, Subnet Mask, Default Gateway, Primary DNS, and/or Secondary DNS. Use information
recorded in Before Installation if applicable.
b Click OK when the IP address was changed successfully message box appears.
11 Reconnect the network cable.
12 When prompted to Insert the Product Key, enter the 25-digit Product Key located on top of the Dell PC and click OK.
NOTE Leave the Set Proxy boxes blank.
13 Activate Windows. If the Host PC is connected to the Internet, Windows will attempt to activate automatically once
the Product Key is inserted. If successful, a popup will appear indicating that Windows has been activated. Click OK
and continue to Step 14. Otherwise, continue with this step.
a On the Activate Windows Dialog, select "Yes, I want to telephone a customer service representative to activate
windows" and click Next.
b Select a location for step 1. Once a location is entered, a phone number will appear in step 2 to call.
c Call this phone number and answer the questions given over the phone. You can use the touch-tone pad on the
phone to enter the number. Provide them with the installation ID.
d Type in the confirmation number in the boxes labeled A-G when they are given to you.
e Click the Next button. When instructed to, click the Finish button.
f The system will restart automatically.
14 After system restart, click OK when notified that the "Windows XP Installation was completed successfully".
15 If the system has a dual port network card for the Host-IRS Connection, verify that the Host-IRS Connection is
active.
a On the Host PC Desktop, right-click on My Network Places and select Properties from the pop-up menu.
b If the Host-IRS Connection has an X through it, physically move the network cable to the open port on the network
card.
c Verify the X disappears.
d Close all windows.

Philips Medical Systems Confidential and Proprietary Information 2 - 10

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

16 Drive Letter Correction.

NOTE In certain circumstances, installation of the Brilliance CT 1.2 Software causes the drive letters of the
EOD, CD-R, and CD drives to become mixed up. Check if your drives are defined properly as listed
below.
a Double-click My Computer.
b Check that your drives are defined as shown below:
Drive C: Local Disk (C:)
Drive D: Local Disk (D:)
Drive E: CD/DVD
Drive F: EOD
Drive G: CD-RW
NOTE If the EOD does not appear, power down the Host by pressing the Power Button on the PC. Wait 10
seconds, then press the Power Button again to power up the Host.
c If your drives are defined properly, skip to the Host Model CD Installation section on the next page. Otherwise,
continue with this Steps d-h and then continue toHost Model CD Installation.
d Right-click on My Computer and select Manage. This will open a Computer Management window.
e Select Disk Management.
f Right-click the button for the drive you want to change and select Change Drive Letter and Paths…
g Click Change and select the correct letter, then click OK.
NOTE The system does not allow two drives with the same letter. This means that if you want to exchange the
drive letters of two or more drives, you should give one of the drives an alternate letter temporarily.
h When all the drive letters have been corrected, close the Computer Management window.
17 Continue with Host Model CD Installation on the next page.

Philips Medical Systems Confidential and Proprietary Information 2 - 11

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

Host Model CD Installation

1 Make sure you are logged in as Administrator. If continuing from the previous page, then you should already be
logged in as Administrator.
2 Insert the Host Model CD into the CD/DVD ROM drive of the Host PC.
3 Double-click My Computer.
4 Double-click the E: drive.
5 Double-click Setup.
6 On the Philips Install Supervisor window, click Start.
NOTE No need for password
NOTE Do not touch the keyboard or mouse until install is complete.
7 When the "Installation completed" message appears at the bottom of the Philips Install Supervisor window, ensure
that all the items are Done, (exit code: 0x00000000). Then click Close on the Philips Install Supervisor window.
Also close the Explorer window.
8 Remove the CD.
9 Continue with the next section: Host Applications Installation.

Philips Medical Systems Confidential and Proprietary Information 2 - 12

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

Host Applications Installation

1 Insert the Host Applications CD into the CD/DVD ROM drive of the Host PC.
2 On the Desktop, double-click My Computer. If My Computer does not appear on the Desktop, then click Start > My
Computer.
3 Double-click on the E: drive, then double-click Setup.
4 On the Philips Install Window, enter "install" in the password field, and then click Start. Wait approximately 10 to 15
minutes as the 3rd party software installs.
NOTE Once the Philips Install Supervisor starts installing components, do not touch the keyboard or mouse.
NOTE The system will Reboot during the Installation, and automatically log back in.
5 During installation, the View/Adjust Gantry Registration settings will appear. Select the correct Rotor Type and click
OK.
6 The next window will ask if the Couch Board has an EIN # incorporated on the label, select Yes or No and click OK.
7 Adjust the date and time if necessary:
NOTE It is critical that the time is set correctly at this point and not modified after the application CD has
been installed. Under certain conditions, modifying the date and time after the application CD has been
installed will result in the option and service keys being corrupted. The only way to correct this
corruption is a full reinstallation.
8 When the "Installation completed" message appears at the bottom of the Philips Install Supervisor window, scroll
through the Install Supervisor and ensure that all the items are Done, (exit code: 0x00000000). Then click Close in
the window.
NOTE If all the items are not "Done, (exit code: 0x00000000)", then go back and reinstall the OS, Model, and
Host Applications software.
9 Remove the CD from the drive.
10 If the system has Dual Monitors, continue with this step. Otherwise, skip to Step 11.
a Right-click on the Desktop and select Properties from the pop-up menu.
b Select the Settings tab.
c Click the Advanced button and select the Quadro4 980 XGL tab. A menu opens on the left.
d Click nView Display Mode.

Philips Medical Systems Confidential and Proprietary Information 2 - 13

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

NOTE If you do not find the nView Display Mode, click Cancel to exit Advanced, select monitor number 2 and
uncheck the 'Extend my windows desktop onto this monitor' button, than click the Apply button. Select
monitor number 1 and go back to step ‘d’.
e In the nView Display Mode area, select the Horizontal span option from the nView Modes drop-down menu.
NOTE If all buttons are grayed out, select monitor number 2 and uncheck the 'Extend my windows desktop
onto this monitor' button, than press Apply button. Select monitor number 1 and try step ‘e’ again.
f Click Apply.
g Click Yes, and then click OK to confirm the settings. The right-hand screen should be activated.
h If the monitors appear swapped, follow Steps i - r. Otherwise, perform Steps n-r.
i click the Advanced button and select the Quadro4 980 XGL tab.
j Click on nView Display2… in the Display pulldown menu.
k Make sure Make this the primary display is checked.
NOTE This will change "nView Display2…" to "nView Display1…" and vice versa.
l Click Apply.
m Click Yes, and then click OK to confirm the settings.
n Make sure that the Screen resolution bar is set to 2560 x 1024.
o Click the Advanced button and select the Monitor tab.
p Verify the Screen Refresh Rate is set to 75Hz. If not, set the rate to 75Hz and click Apply. Otherwise, click OK.
q Click OK on the Display properties window.
r Close all open windows on the Desktop.
11 Log out of Administrator:
a Click Start > Shut Down.
b Select Log Off Administrator.
c Click OK.
12 Continue with Host Utilities Installation on the next page.

Philips Medical Systems Confidential and Proprietary Information 2 - 14

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

Host Utilities Installation

1 Login to the Host PC as philips_service (use philips_service password).
NOTE The first time you log into any account, you will see a message popup and then you will be logged out of
the account automatically. Please log back in before continuing.
2 Insert the Host Utilities CD into the CD/DVD ROM drive of the Host PC.
3 Click Start > My Computer.
4 Double-click the E: drive.
5 Double-click Setup.
6 Enter Username and Password.
NOTE Enter philips_service for the Username and enter the philips_service password for the Password.
7 Click the Start Button.
NOTE Do not touch the keyboard or mouse until install is complete, other than to enter the K2000 Visa Entry
when the window appears.
8 Setting the K2D Visa:
a Go to the K2000 Visa Entry window that has been automatically opened.
b Obtain the Machine ID (needed to get the visa key).
c Obtain a visa (the K2D key)
NOTE Either the K2 Visa or the K2000B Visa key can be used when obtaining the key from the web site.
d Enter the visa in the K2000 Visa Entry window, and click OK.
e Click Done.
NOTE Do not touch the keyboard or mouse at this time. During the installation process the system will
reboot several times.
9 When the "Installation completed" message appears at the bottom of the Philips Install Supervisor window, ensure
that all the items are Done, (exit code: 0x00000000). Then click Close in the Philips Install Supervisor window. Also
close the Windows Explorer window if it is still open.
10 Remove the CD.

Philips Medical Systems Confidential and Proprietary Information 2 - 15

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

11 CIRS Service Utilities Install:

a Make sure you are logged in as philips_service (You already should be after the install is complete).
b Click Start > My Computer.
c Navigate to C:\Cirs_temp.
d Double-click on SUtils.vbs.
e If the "user account philips_service already exist" window appears, click OK.
f When the "Service Tools Installation Completed" window appears, click OK.
g Close the Explorer window.
h Continue with the Host Update CD installation below.

Host Update CD
1 Make sure you are logged in as philips_service.
2 Insert the Host Update CD into the CD/DVD ROM drive of the HOST PC.
3 Click Start > My Computer.
4 Double-click the E: drive.
5 Double-click Setup.
6 Click Start.
NOTE No need to change username or password. Wait approximately 5 minutes as the software is installed.
NOTE Do not touch the keyboard or mouse until install is complete.
7 When the "Installation completed" message appears at the bottom of the "Philips Install Supervisor" window, ensure
that all the items are "Done, (exit code: 0x00000000)". Then click "Close" in the "Philips Install Supervisor" window.
Also close the Explorer window.
8 Remove the CD.
9 Continue with Operator’s Manual CD Installation on the next page.

Philips Medical Systems Confidential and Proprietary Information 2 - 16

Brilliance CT Software Installation Manual Version 1.2 Host Software Installation for 16 Power configuration

Operator’s Manual CD Installation

1 Insert the CD labeled: Brilliance_CT_OperationsManual_1.2.0.1.
2 Click Start > My Computer.
3 Double-click the E: drive.
4 Double-click Setup.
5 Click Start.
NOTE No need for password. Wait approximately 5 minutes as the software is installed.
NOTE Do not touch the keyboard or mouse until install is complete.
6 When the Installation completed message appears at the bottom of the "Philips Install Supervisor" window, ensure
that all the items are Done, (exit code: 0x00000000). Then click "Close" in the "Philips Install Supervisor" window.
Also close the Windows Explorer window.
7 Remove the CD.
8 Continue with Host System Configuration and Registration on the next page.

Philips Medical Systems Confidential and Proprietary Information 2 - 17

Brilliance CT Software Installation Manual Version 1.2 Host System Configuration and Registration

Host System Configuration and Registration

NOTE The olevel_service and CT configuration and registration sections must be completed regardless of
diagnostic level. Only philips_service should complete the philips_service configuration and registration
section.

olevel_Service Configuration and Registration

1 Make sure you are logged in as olevel_service.
NOTE The first time you log into any account, you will see a message popup and then you will be logged out of
the account automatically. Please log back in before continuing.
NOTE When logging back into the o_level account, an O-Level Diagnostics Window will appear.
2 If the IP address recorded for the Host-IRS Connection in the Before Installation section is not 192.168.0.100 or if
192.168.0.100 will cause a conflict with the Hospital Network, configure the Host-IRS Connection:
a Click the Adjust Hospital-Recon Network button.
b Click Yes to change the subnet to 10.168.0.
NOTE If the IP Address has been changed for the Host-IRS Connection, you will need to change the IP
Address of the CIRS Server(s) to be on the same subnet as the Host-IRS Connection. Please follow the
instructions in the CIRS Service Manual.
3 Set Registry Values:
a Click Get/Set Gantry Registry Settings button.
b Enter SL_RL laser gap in 0.1mm, default: 3159
NOTE Only modify the SL_RL laser gap in 0.1mm, default: 3159 value if it is not equal to what was recorded in
the Before Installation section.
c Click OK.
4 If this is not a new installation and files backed up prior to the software installation need to be restored, continue with
this step. Otherwise, skip to Step 5.
a Insert the EOD.

Philips Medical Systems Confidential and Proprietary Information 3-1

Brilliance CT Software Installation Manual Version 1.2 Host System Configuration and Registration

b Click the Backup/Restore Site Data button.

c Select the Restore tab.
d Double click on Optical Drive (F:) to expand the menu tree.
e Select the directory of your most recent backup. Then click OK.
NOTE Do NOT restore System Parameters and Patient Catalogue if the version of the software being
installed is not identical to the previously installed version.
f Click Start Restore. Please be patient.
g Click OK when complete.
h Click Close on the Log window.
i Click Exit on the Backup/Restore window.
5 If this is a brand new installation and not an upgrade from a previous version (without doing a restore), or if the
feature set for a specific customer site has changed, continue with this step to enter the new options key. Otherwise,
skip to Step 6.
a Click the Update Option Key button.
b Enter the options key.
c Close any open windows.
6 Click the Adjust File Properties button on the O-Level Diagnostics window to change everything in the C:\usr
directory and subdirectories to NOT read-only.
7 Run RegisterGS and RegisterServiceTools:
a Click the Reregister libraries button.
NOTE During this process the Command Prompt will tell you to press any key to continue.
b Click OK or Yes in any dialog boxes that appear.
NOTE Check for success in all but PETMS.
8 Logout of olevel_service by clicking the Log out button.

Philips Medical Systems Confidential and Proprietary Information 3-2

Brilliance CT Software Installation Manual Version 1.2 Host System Configuration and Registration

philips_service Configuration and Registration

1 Make sure you are logged in as philips_service.
NOTE The first time you log into any account, you will see a message popup and then you will be logged out of
the account automatically. Please log back in before continuing.
2 Update Service Tools:
NOTE You must have a valid Visa Key before proceeding with this step.
a Double-click the Service Tools icon on the
desktop.
b Select General Tools > CAN Send
c Select the Gantry message category (#1).
d Select the
GANTRY_SERIES_LOAD_REQ message
(#2).
e Click the LoadFrom button on top of the
message data view box (#3).
f Navigate to
C:\usr\diamond.root\bin\ServiceTools.
g Select the NoLoadSeries.tSeries file and
click Open (#4).

Philips Medical Systems Confidential and Proprietary Information 3-3

Brilliance CT Software Installation Manual Version 1.2 Host System Configuration and Registration

h Click on the value of the

firstShotTriggerType parameter (#5).
i From the drop down list box, select
FIRST_SHOT_AUTO_TRIGGER (#6)
j Click the SaveTo button on top of the
message data view box.
k Navigate to
C:\usr\diamond.root\bin\ServiceTools.
l Select the NoLoadSeries.tSeries file and
click Save.
m Click Yes to confirm.
n Repeat Steps e-m using the
Leakage.tSeries file.
o Close the Service Tools window.

3 Verify Tube Conditioning:

a Double-click on the Scanner App icon on the desktop.
b Click on Home > Tube Conditioning.
NOTE If the Tube Conditioning window does not appear on the screen, the Brilliance CT Miscellaneous
component of the Host Application CD might not be installed correctly. See Appendix B - Re-install
Brilliance CT Miscellaneous Component for instructions.
4 Log off of philips_service by clicking Logout on the Scanner Application. Click Yes to confirm.

Philips Medical Systems Confidential and Proprietary Information 3-4

Brilliance CT Software Installation Manual Version 1.2 Host System Configuration and Registration

CT Configuration and Registration

1 Make sure you are logged in as user CT. There is no password.
NOTE The first time you log into any account, you will see a message popup and then you will be logged out of
the account automatically. Please log back in before continuing.
2 Click End Study to clear patient data from the screen, and then click Yes to confirm.
3 Update the Gantry Position only if the gantry is on the right and the couch is on the left when viewing them from the
console. Otherwise, skip to Step 4.
a Click on Home > Utilities > Misc.
b Select Set User Mode.
c Select Service (password: mxtech). Make sure Caps Lock is off.
d Click OK, then Close.
e Select Set Scanner Position.
f Update Gantry Position, and click Close.
g Select Set User Mode.
h Select Technologist, and click Close.
4 Update Default Storage Devices if applicable:
a Click on Home > Utilities > Misc.
b Select Default Storage Devices.
c Update Default Storage Devices options to match the information recorded in the Before Installation section.
d Click OK.
5 Update Hospital Name and default printer if applicable:
a Click Home > Utilities > Misc.
b Click Configuration.
c Select Institution.
d Update the Institution Name with the Hospital name.
e Click OK.
f Click the Filming tab from the workflow menubar.
g Click File, and select Printer.

Philips Medical Systems Confidential and Proprietary Information 3-5

Brilliance CT Software Installation Manual Version 1.2 Host System Configuration and Registration

h Select the appropriate printer and click OK.

i On the Filming window, click File > Close.
6 Update Patient Data options if applicable.
a Click on Home > Utilities > Diagnostic.
b Select Service Parameters.
c Select Patient Data.
d Update Patient Data options to match the information recorded in the Before Installation section.
e Select HIS/RIS.
f Update HIS/RIS options to match the information recorded in the Before Installation section.
g Make sure the Requested Procedure ID, Scheduled Procedure Step Start Date, and Scheduled Procedure
Step Start Time fields are selected.
h Click OK.
7 If Scan Protocols were restored previously, update the protocols.
NOTE If you are upgrading from version Brilliance 16P 1.0 perform this step. If you are upgrading from a
previous version of Brilliance CT 1.2 you may skip this step. If in doubt, perform this step.
NOTE Make sure Caps Lock is off before proceeding.
a Click on Home > Utilities > Service.
b Select Service Terminal and type in the password: letmein, then press the <Enter> key.
c In the Service Terminal window, type ./Protocol21Update.csh, then press the <Enter> key.
d When prompted, type y and press the <Enter> key to continue.
NOTE This may take a while depending on the number of protocols to convert. You will see Destroy and
Converted messages. These are normal.
e When prompted, press <Enter>.
f The final message displayed by the utility will indicate how many protocols were converted successfully. If any
protocols failed conversion, write these protocols down. These protocols will need to be deleted and re-entered
manually. If the protocols that failed to convert are not deleted, the user will get an Invalid Step message when
they try to use them.
g In the Service Terminal window, type exit and press the <Enter> key to dismiss the window.

Philips Medical Systems Confidential and Proprietary Information 3-6

Brilliance CT Software Installation Manual Version 1.2 Host System Configuration and Registration

8 Restart the host computer without logging out from the Scanner Application. Only click on anything that requests to
"end now", otherwise ignore error messages.
a Click Start > Shutdown.
b Select Restart from the drop-down menu.
c Click OK.
9 Continue with I-Box Software Installation installation on the next page.

Philips Medical Systems Confidential and Proprietary Information 3-7

Brilliance CT Software Installation Manual Version 1.2 I-Box Software Installation

I-Box Software Installation

1 Login as philips_service (use the philips_service password) if not already logged in. Make sure Caps Lock is off.
2 Double-click the IBoxDiag icon on the desktop.
3 Select Manual Test and click Next.

Philips Medical Systems Confidential and Proprietary Information 4-1

Brilliance CT Software Installation Manual Version 1.2 I-Box Software Installation

4 Click Get Version. If the I-Box version is 2.19, and FPGA version is either 2.1 or 1.3 (both should work), click OK.
Exit the IBoxDiag program and skip to Gantry Controller Boards Software Installation on the next page. Otherwise,
continue to Step 5.

5 Click Back.
6 Select IBox program upgrade and click Next.
7 If you want to Backup Current Program on U40, input a path to save the program and click Next, then click Next
again. Otherwise click Skip.
8 When asked to Save new program, click Browse and navigate to
C:\usr\diamond.root\I-BoxSW\I-Box_ver_2.19_for_u40.bix and click Open.
9 Click Next to download the firmware to U40.
10 Click Yes when the I-Box diagnostics successfully downloaded window appears.
11 Click Exit to close the I-Box Diagnostics Wizard.
12 Continue with Gantry Controller Boards Software Installation on the next page.

Philips Medical Systems Confidential and Proprietary Information 4-2

Brilliance CT Software Installation Manual Version 1.2 Gantry Controller Boards Software Installation

Gantry Controller Boards Software Installation

In order to ensure that the latest versions of gantry software are installed, the gantry software must be reloaded
whenever a new application software CD is installed on the Host PC.
The Automation Utilities are available for proprietary use only. Third party is provided with Connect to controller where
the burn process is manual as it was in previous releases. Prior to using these procedures, be sure to open the E-Stop
by pressing the red button on the CT Box. If you forget to do this, it sometimes results in certain boards, predominately
the Couch and/or the DMC, yielding NO RESPONSE. To remedy this, just back out to the menu that says “All
controllers in utility mode”, select this option again, and continue. If the system contains a GMP board, it will respond as
the MDP. The menus will indicate NO RESPONSE from the TDP since the GMP is its replacement.

Reburning Release 2.0 Boot and Application Flash.

NOTE This assumes the release 2.0 Utility Server is being used.
1 Launch Service Tools, and select Controller Utilities.
2 Select Field Service Engineer.
3 Click on Connect.
4 Select Service mode.
5 Select Utilities, and click Submit.
6 Check the boxes for all the boards to be reburned.
7 Check the Save NVRAM box.
8 Check the RAM downloader box.
9 Check the Back up boot flash burner box.
10 Check the Boot flash burner box.
11 Check the Application flash burner box.
12 Check the Controller reset box.
13 Click on Submit.
14 Click Return.
15 Click Return.
16 Select Application mode.

Philips Medical Systems Confidential and Proprietary Information 5-1

Brilliance CT Software Installation Manual Version 1.2 Gantry Controller Boards Software Installation

17 Exit Service Tools.

18 Power cycle the scanner
19 Verify the flash has been reburned with Release 2.0.
20 Continue with Optional Equipment Software Installation on the next page.

Philips Medical Systems Confidential and Proprietary Information 5-2

Brilliance CT Software Installation Manual Version 1.2 Optional Equipment Software Installation

Optional Equipment Software Installation

If the site does not have the following printers to install, then go to System Calibration. If you have to reload the CIRS
OS and Application software, complete those procedures first, then go to System Calibration.

Installation of HP Laserjet 2500 or Lexmark Optra 45

Certain sites may have these printers to do report generation. Installation of driver software to control these printers is
required. This is how to install the driver software (after all other system software has been installed).
1 Login as philips_service on the Host PC.
2 Plug in the USB cable from a powered up printer into the Host PC.
3 A new “Hardware Found” window will popup.
4 Select "Install from a list or specified location..." and click NEXT.
5 Select "Don't search. I will choose the driver to install..." and click NEXT.
6 Select "Printers" and click NEXT.
7 Select "HP" from the left column and "HP 2500C Series PS 3 or "Lexmark" and Lexmark Optra Color 45 PS
depending on the printer being installed.
8 Select "Yes" to the question concerned about "... installing the device is not recommended...". It appears an identical
Device name match is required and this does NOT occur for these printers even though the selected driver works
fine.
9 Click Finish.
10 Continue with System Calibration (or CIRS OS and Application installation if needed).

Philips Medical Systems Confidential and Proprietary Information 6-1

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

CIRS OS Installation

CIRS server hardware

The CIRS hardware consists of three servers and an Ethernet switch in a rack. The CIRS servers are referred to as
CIRS-S1, CIRS-S2, and CIRS-S3. In the rack, CIRS-S1 is located at the bottom, CIRS-S2 is in the middle, and CIRS-
S3 is at the top. CIRS-S2 has a 3DBP board installed. CIRS-S1 has an ACQ16 board installed.

CIRS operating system installation

The CIRS server software installation is composed of two parts, the operating system install and the CIRS application
install. The operating system install is performed one time, during manufacturing. Manufacturing and Service should
refer to the Service Manual for Reconstruction (CIRS), to setup the system BIOS, install the operating system software
or run board diagnostics.

Monitor, keyboard, mouse

In order to update/install the Operating System on a CIRS server, a monitor, keyboard and mouse must be connected
directly to the server.

Network connection
Make sure the CIRS Ethernet switch is not connected to a hospital or Philips network. This prevents viruses during the
installation.

Philips Medical Systems Confidential and Proprietary Information 7-1

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

CIRS BIOS Settings

NOTE The minimal required version of BIOS/BMC/FRU/SDR should be:

Server BIOS BMC FRU/SDR What actually appears:

S1 (SE7501BR2) P15-0074 1.18 5.6.I or 5.5.I SBR20.86B.0074.P15
S2/S3 (SE7501WV2) P16-0190 1.19 5.6.A SWVR25.86B.0190.P16

NOTE BIOS Setup could be done by console redirection through either IPMI hyper terminal telnet session or
DPC Console (see the CIRS Service Manual section “Tools for Advanced Server’s Diagnostic” for tools
description). You can also attach a monitor, keyboard, and mouse directly to the servers.

To check the current version:

1 Go into BIOS Setup (by pressing F2 at boot up).
2 On the BIOS menu, select Server > System Management.
3 If the version does not meet the requirement see Appendix D - Update BIOS Setting for CIRS Servers for BIOS
update instructions. If the version does meet the requirement, continue with CIRS Software Installation.

CIRS Software Installation

NOTE For 6-slice, 10-slice, and 16-slice systems, use the Software CD labeled CIRS-3.4.1.6.
For 16 Power systems, use the Software CD labeled CIRS-3.4.1.7.
For a new install, begin at Before Installation on page 7-3, then continue with Installing OS (Windows XP) on page 7-5.
If the system was previously installed, begin with Previously installed systems on page 7-4 below, then continue with
Installing OS (Windows XP) page 7-5.

Philips Medical Systems Confidential and Proprietary Information 7-2

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

Before Installation

New Installation using Serial over LAN

NOTE New installation only for Brilliance CT 6, 10, 16-slice and 16 Power configurations using Serial over LAN
(SOL) (performed on new unformatted hard drive) - Service Partition Installation
NOTE For multiple servers configuration the same installation has to be performer for each server.
1 Insert CD marked "PHILIPS, System Diagnostic Utilities, Disk 1 of 1, Part Number: SOFTGR-064, Revision: 00X"
into CD-ROM drive on the Server.
NOTE The following steps apply only to remote (SOL) installation. If installation is done using local
keyboard/monitor just reboot server after inserting CD into CD-ROM drive, select "Restore Service
Partition" menu option, and answer "Yes" to the question if you want to load the image to the disk.
Installation of service partition goes automatically. You will be presented with the DOS prompt when it
is completed. This will format hard drive and destroy all data on it (CIRS Tables, not RawData).
2 On the Client PC, double-click on the IPMI.ht icon on the desktop to open the IPMI HyperTerminal.
3 At the SERVER: prompt, enter Server IP address (192.168.0.XXX) where XXX is:
— For S1 - 150
— For S2 - 151
— For S3 - 152
4 Press <Enter> at USER: prompt.
5 Press <Enter> at the PASSWORD: prompt.
6 You should see “Login Successful” and the dpccli> prompt (see dpccli command reference in ISM section).
7 Type “reset” and then “c” for console.
8 Select Restore Service Partition menu option and answer Yes to the question if you want to load the image to the
disk. Installation of the service partition goes automatically, but you will not see the GUI part of the installation. You
will be presented with the DOS prompt when installation is completed.
9 Remove CD when installation is completed (you will get an A:\ prompt).
10 Type '~.' To return back to dpccli> prompt.
11 Continue with Installing OS (Windows XP) on page 7-5.

Philips Medical Systems Confidential and Proprietary Information 7-3

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

Previously installed systems

Using Windows Remote Desktop, connect to the server that you will install the OS on, and obtain the following network
values:

Computer name for each server:

1 Click on Start to display the Start menu.
2 On the Start menu, right-click on My Computer and select Properties.
3 On the System Properties Window, click on the Computer Name tab.
4 Note the value next to Full Computer Name:
5 Click OK to close the System Properties Window.

IP Address and network settings (for each Server):

1 On the Desktop, double-click on the Network Connections icon, or click Start > Control Panel > Network
Connections.
2 Right-click on Local Area Connection, and select Properties from the menu.
3 Click on Internet Protocol (TCP/IP).
4 Click the Properties button.
5 Record the following settings:
— IP address
— Subnet mask
— Default Gateway
6 Click on OK to dismiss dialog boxes.
7 Right-click on Local Area Connection 2, and select Properties from the menu.
8 Follow Steps 3 – 6.
9 Continue with Installing OS (Windows XP) on page 7-5.

Philips Medical Systems Confidential and Proprietary Information 7-4

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

Installing OS (Windows XP)

Attach a monitor, keyboard, and mouse to the server, or connect to the server via SOL. For SOL procedures, see the
Brilliance CT 16 Power CIRS Service Manual.
NOTE For SOL installation: Remote connection to the system will be lost when GUI part of OS installation
begins.
NOTE The following instructions were written for OS install with a monitor, keyboard, and mouse attached to
the server.
1 Insert CD marked CIRS-X.X.X.X into CD-ROM drive of the server and reboot the Recon PC. Booting from the CD
will start the OS installation.
NOTE When you insert the CD into the CD-ROM Drive, a message will appear asking if you want to install CIRS
software. Click No, and reboot the server.
2 After boot the following screen will appear:
* Philips Medical Systems - CIRS Operating System Installation
*
* NOTE: Installation of this software will
* DESTROY any data currently on the hard disk.
*
* Do you want to install this software?
* Press Y to Continue (partitions disk, then reboot PC)
* Press N to Stop the installation (reboot PC without destroying data)
3 Answer Y to the question above if you want to install the operating system. This will partition the disk and reboot PC.
4 The following message would appear on the screen after reboot:
*Systems prior to serial number 8060 may have been purchased
*with Windows 2000. These systems require an "upgrade" key
*which is included in the installation instructions in a list.
*Does your system appear on the list?
[Y,N]
Answer N, and continue with Step 5.

Philips Medical Systems Confidential and Proprietary Information 7-5

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

5 When prompted, enter the Windows XP product key as it appears on the tag (or
the upgrade key from the list if applicable) and press <Enter>.
6 Windows XP Professional Setup will start.

NOTE Remove the CIRS CD when prompted:

* Please Remove the CD-ROM.
* Press the Ctrl-Alt-Delete keys simultaneously to continue with the installation of Windows XP
which will take approximately 30 min.
* When the Windows XP Installation is complete, re-insert the CD to install the CIRS software.
NOTE If using SOL, do NOT press Ctrl-Alt-Del, instead type '~.' And at the dpccli> prompt, type ‘reset’ and
then ‘c’

CAUTION Do not re-insert the CD until instructed to do so in the CIRS Application Software
Installation section.
7 When the Windows XP installation is complete, the server will reboot and display the login prompt.
8 Login as “philips_serevice”, using the philips_serevice password.
9 When when login completes, you will see system settings change box with the following message:
Windows has finished installing new devices. The software that supports your device requires the
you restart your computer. You must restart your computer before the new settings will take
effect.
Do you want to restart your computer now?
10 Click Yes.

Philips Medical Systems Confidential and Proprietary Information 7-6

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

11 First time you login you may see the Found New Hardware Wizard:

12 Click Next to complete the installation, then click Cancel when asked if you want to reboot the Recon PC.
Important! After OS installation using CIRS CD, or if server came directly from Granite Microsystems, each server's
IP address is preset to 192.168.0.250 on one NIC. It is absolutely critical to login to each server (directly
or by Remote Desktop Connections) right after the OS installation of the server has been completed, and
modify each server's IP addresses for both NICs to the appropriate values. Do not wait until after installing
the OS on all three servers, because it would create an IP address conflict since all servers are configured
with the IP address during OS install. Also, make sure that both NICs (data and diagnostic) on each
server have ethernet cables plugged in before attempting to connect to the server remotely. If any of the
servers report an IP address conflict, boot to the service partition, run the System Setup Utility, and check
the LAN configuration to make sure that the correct IP address is assigned the BMC NVRAM of the
server. See Appendix C - Server Setup Instructions - Server Setup Instructions for more information
13 Enter IP addresses:
a Click Start > Control Panel > Network and Internet Connections > Network Connections.
b On the Network Connections Window, double-click the connection named Local Area Connection 2.
c On the Local Area Connection 2 Status page, click Properties to open the Properties page.

Philips Medical Systems Confidential and Proprietary Information 7-7

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

d On the Local Area Connection 2 Properties page, click Internet Protocol (TCP/IP) to select it, then click
Properties.
e On the TCP/IP Properties page, select Use the following IP address and enter:
— 192.168.0.200 for Server S1
— 192.168.0.210 for Server S2
— 192.168.0.220 for Server S3
NOTE In the event that the hospital's LAN uses the 192.168.0.XXX IP addresses, use 10.168.0.XXX instead
(replace all occurrences of 192 with 10). Keep the remaining values the same. You must also change the
“Hosts” file, located at C:\Windows\system32\drivers\etc\hosts, to include the replacement. Right-click on
the file and select Open With... > Notepad. Replace all occurrences of 192 with 10. Do this on all servers
in your configuration. For example if you have a 2-server configuration, you would have to change the
Hosts file on both servers.
f In the Subnet Mask field, enter 255.255.255.0.
g Click OK on the TCP/IP Properties page.
h Click Close on the Local Area Connection 2 Properties page.
i Click Close on the Local Area Connection 2 Status page.
j On the Network Connections Window, double-click the connection named Local Area Connection.
k On the Local Area Connection Status page, click Properties to open the Properties page.
l On the Local Area Connection Properties page, click Internet Protocol (TCP/IP) to select it, then click
Properties.
m On the TCP/IP Properties page, select Use the following IP address and enter:
— 192.168.0.150 for Server S1
— 192.168.0.151 for Server S2
— 192.168.0.152 for Server S3
NOTE In the event that the hospital's LAN uses the 192.168.0.XXX IP addresses, use 10.168.0.XXX instead
(replace all occurrences of 192 with 10). Keep the remaining values the same. You must also change the
“Hosts” file, located at C:\Windows\system32\drivers\etc\hosts, to include the replacement. Right-click on
the file and select Open With... > Notepad. Replace all occurrences of 192 with 10. Do this on all servers
in your configuration. For example if you have a 2-server configuration, you would have to change the
Hosts file on both servers.

Philips Medical Systems Confidential and Proprietary Information 7-8

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

n In the Subnet Mask field, enter 255.255.255.0.

o Click OK on the TCP/IP Properties page.
p Click Close on the Local Area Connection Properties page.
q Click Close on the Local Area Connection Status page.
r Close the Network Connections Window.
NOTE If using SOL, then the desktop will most likely be gray. Close the Remote Desktop session and then log
in again with Remote Desktop using the revised IP address of Step ‘e’ above.
14 Change computer name:
a Click Start, and from the Start Menu, right-click on My Computer and
select Properties.
b On the System Properties Window, click on the Computer Name tab.
c Click Change, and on the Computer Name Changes Popup, enter
RECONXXXX in the Computer Name Field. Where XXXX is the
system’s Serial Number (e.g 8056).
d Click OK.
e Click OK again when prompted to restart the computer.
f Click OK on the System Properties Window.
g Click Yes, in the System Setup Change dialog to restart the Server.

Philips Medical Systems Confidential and Proprietary Information 7-9

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

Windows Activation
When Windows reboots, the activation popup window would appear at the bottom of the screen. If the window does not
appear, click on the yellow key icon on the lower bar. You can also click Start > All Programs > Activate Windows.
The following activation screen will appear.
If the Recon PC is connected to the Internet select the first option (Internet activation), otherwise select the second
option (telephone activation) and follow the activation instructions.
NOTE If the yellow key icon is not present, Click Start > Run and enter:
“C:\WINDOWS\system32\oobe\msoobe.exe /a”. This will bring up the activation window.

Philips Medical Systems Confidential and Proprietary Information 7 - 10

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

Activate RAID disk (S1 server only )

Every time you reinstall the OS, you have to activate the RAID disk to make it accessible.
1 Click Start, and on the Start Menu right-click on My Computer.
2 Click Manage.
3 On the Computer Management Menu, double-click on Disk Management. You will see the following screen:

4 Right-click on the first Foreign disk (Disk 1) and select Import Foreign Disk.

Philips Medical Systems Confidential and Proprietary Information 7 - 11

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

5 The following screen appears.

6 Click OK.

7 Click OK again. The final screen will look like the one below.

Philips Medical Systems Confidential and Proprietary Information 7 - 12

Brilliance CT Software Installation Manual Version 1.2 CIRS OS Installation

8 Close the Computer Management

window.
9 For Brilliance CT Products, create
Folder "RawData" on F: drive (striped
volume RAID disk).
a Right-click on Start, and select
Explore from the menu.
b In Windows Explorer, double-click
on the F: drive. In the right-side
display window, right-click and
select New > Folder. Name it
RawData.
10 Configure Recycle Bin to remove
files immediately:
a On the Desktop, right-click on the
Recycle Bin and select
Properties from the menu.
b On the Global Tab, click on
“Configure Drives Independently”.
c Click on the Local Disk (F:) Tab,
and click on “Do not move files to
Recycle Bin. Remove files immediately when deleted”.
11 Paging needs to be disabled and virtual memory set to zero by doing the following:
a Go to Start > My Computer; right-click and select Properties.
b Click on the Advanced tab, and select Settings under Performance.
c Click the Advanced tab, and select the Change button under Virtual Memory.
d Click on the No Paging File radio button to select it, and click Set.
e Click Yes to any warnings.
f Click No if you are asked to restart the computer, you will do this later in the installation process.
g Click OK to exit out of all windows.
12 Restart S1. If using Remote Desktop Connection: right-click on the Windows Taskbar and select Task Manager. On
the Task Manger Menu bar, click Shutdown > Restart. This will also work if you connected directly to the server with
a Monitor, Keyboard and Mouse.
13 Continue with the next section, CIRS Application Software Installation.

Philips Medical Systems Confidential and Proprietary Information 7 - 13

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

CIRS Application Software Installation

NOTE For 6-slice, 10-slice, and 16-slice systems, use the Software CD labeled CIRS-3.4.1.6.
For 16 Power systems, use the Software CD labeled CIRS-3.4.1.7.
NOTE If you are reloading application software, then follow the steps on this page. If this a new install of
application software, start with Remote Desktop Connection to the Server.
NOTE Only follow the instructions that are applicable to your server configuration:
Three Server Configuration (S1, S2, and S3) on page 8-3
Two Server Configuration (S1 and S2) on page 8-11
One Server Configuration (S1 only) on page 8-19

To check current software version:

1 Open the Command Window by double clicking on Recon icon on the desktop.
2 At the prompt type "Supervisor.exe -ver". The line with "CIRS- X.X.X.X" (e.g. CIRS-3.4.1.7) will have the label of the
current CIRS application software.
NOTE For Brilliance CT 16 Power Configuration: When system has to be downgraded (going from 3 or 2
servers to 2 or 1) the following steps have to be performed:
— Remove 3DBP card and Power Module from the going away server (assuming they pass the diagnostic) and plug
them into remaining server (S1 is the only necessary server).
— Reload CIRS software.
NOTE CIRS Application install destroys all calibration tables on CIRS Servers.

Philips Medical Systems Confidential and Proprietary Information 8-1

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

Remote Desktop Connection to the Server

NOTE Can only be performed if the Server is configured with the assigned static IP address, otherwise a direct
connection to the server with Video/Keyboard/Mouse is required.
1 On the Host PC, click Start > All Programs >
Accessories > Communications > Remote Desktop
Connections.
2 On the General Tab, enter the Server’s IP address in the
Computer: field. If the tabs are not displayed, click on the
Options button to display them.
— 192.168.0.200 for S1
— 192.168.0.210 for S2
— 192.168.0.220 for S2
In the event that the hospital's LAN uses the
192.168.0.XXX IP addresses, use 10.168.0.XXX
instead (replace all occurrences of 192 with 10).
Keep the remaining values the same.
3 For User Name, enter philips_service.
4 For Password, enter service_only.
5 Click the Local Resources tab, and under Local
Devices, click on Disk Drives to select it. Then click on
Printers to unselect it.
6 Click Connect at the bottom of the window to initiate the
Remote Desktop Connection to the Server.

Philips Medical Systems Confidential and Proprietary Information 8-2

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

Install Application Software on a Three Server Configuration

1 Login to the S1 server (192.168.0.200) from the Host.
a Open CIRS folder on the Host PC Desktop or Service Laptop.
b Double-click the Remote Desktop icon.
c Click OK at the Security Warning.
d At the login prompt, enter “philips_service”. For the Password, use the philips_service password.
e Click OK.
NOTE If a CIRS server is started or rebooted, you must wait at least three minutes before you can login using
Remote Desktop Connection.
2 Disable the CIRS services.
NOTE Follow Steps 2 - 11 only if you are reloading or updating application software. If this is a new install of
application software, go to Step 12 .
a Double-click the Services icon.
b Right-click on CIRS Supervisor Service.
c Select Properties.
d Change Startup type: to Disabled.
e Click OK.
f Right-click on CIRS Resource Proxy Service.
g Select Properties
h Change Startup type: to Disabled.
i Click OK.
j Right-click on CIRS Recon On/Off Service.
k Select Properties.
l Change Startup type: to Disabled.
m Click OK.
n Close the Remote Desktop Connection to S1.

Philips Medical Systems Confidential and Proprietary Information 8-3

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

3 Login to the S3 server (192.168.0.220) from the Host. Refer to Step 1.

4 Disable the CIRS services on S3 as described in Step 2.
5 Close the Remote Desktop Connection to S3.
6 Login to the S2 server (192.168.0.210) from the Host. Refer to Step 1.
7 Disable the CIRS services as described Step 2.
8 Close the Remote Desktop Connection to S2.
9 Power-off all servers.
a Power off each server by depressing and holding the switch on the front of the server until the green light to the left
of the switch goes off.
10 Power-on all servers.
a Power on each server by depressing and holding the switch on the front of the server until the green light to the
left of the switch illuminates. The CIRS servers must be powered-on in the proper order:
— Power-on S2 and S3
— Wait at least 3 minutes
— Power-on S1
NOTE You must wait at least three minutes before you can login using Remote Desktop Connection.
11 Wait at least three minutes.
12 Login to the S3 server (192.168.0.220) from the Host. Refer to Step 1.
13 Install application software.
a Insert CD-ROM labeled CIRS-X.X.X.X into the CD drive of the CIRS server.
b If CD does not autoplay after inserting the disk:
— Click Start > My Computer.
— Double-click on the blue ball that says CIRS.
c At the Install CIRS software? prompt, click Yes.

Philips Medical Systems Confidential and Proprietary Information 8-4

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

d Click Yes to all prompts until the following prompt: CIRS Installation Complete! Choose OK to reboot the
computer. Click Cancel at this prompt.
e Remove the CIRS-X.X.X.X CD-ROM from the CD drive!
f Close the My Computer Window.
g Delete the AcqTestGUI icon (for Brilliance CT 16 Power, if present).
14 Close the Remote Desktop Connection to S3.
15 Login to the S2 server (192.168.0.210) from the Host. Refer to Step1.
16 Install application software as described in Step 13.
17 Update the 3DBP device driver.
a Click Start, then right-click on My Computer.
b Select Manage.
c Click Device manager.
d Click the [+] on Philips back projection devices.
e Right-click 3DBP Backprojection board.
f Select Update driver…
g Select “Install from a list or specific location (Advanced)”.
h Click Next.
i Select “Don't search. I will choose the driver to install”
j Click Next.
k Click Have Disk…
l Enter C:\Program Files\Philips\CIRS\drivers.

Philips Medical Systems Confidential and Proprietary Information 8-5

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

m Click OK.
n Click Next.
o Click Finish.
p Close the Computer Management Window.
18 Update 3DBP board FPGA.
a Double-click on the 3DBP Diagnostics icon to start the CIRS 3DBP Board Diagnostics application

b Click JTAG Download, to launch the JTAG Download window.

Philips Medical Systems Confidential and Proprietary Information 8-6

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

c In the JTAG Download window, click Select File.

d Navigate to the C:\ProgramFiles\Philips\CIRS\3DBP folder.
e Click the 3DBP_vxxxx.svf file, where xxxx is the version indicator.
NOTE Only one .svf file exists in the folder.
f Click Open.
g In the JTAG Download window, click OK.
NOTE If the FPGA version is already up-to-date, a dialog box will indicate that the update will not be done.
Click <OK> and skip the next step below.
h In the BpDiagGUI window, click OK.
i In the CIRS 3DBP Board Diagnostics window, click Quit.
j The downloaded programming file for the FPGA will not take effect until the power to the board is cycled.
19 Close the Remote Desktop Connection to S2.
20 Login to the S1 server (192.168.0.200) from the Host. Refer to Step 1.
21 Install application software on S1 as described in Step 13.

Philips Medical Systems Confidential and Proprietary Information 8-7

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

22 Update the acquisition device driver.

a Click Start, then right-click My Computer.
b Select Manage.
c Click Device manager.
d Click the [+] on Philips acquisition devices.
e Depending on the board installed, right-click on:
f Philips ACQ board (1.1Gb) 4535-670-23021
g Philips ACQ board (800Mbit) 4535-670-05131
h Philips ACQ board (5.3Gb) 4535-670-26141
i Select Update driver…
j Select "Install from a list or specific location (Advanced)".
k Click Next.
l Select "Don't search. I will choose the driver to install".
m Click Next.
n Click Have Disk…
o Enter C:\Program Files\Philips\CIRS\drivers.
p Click OK.
q Click Next.
r Click Finish.
s Close the Computer Management Window.
23 Perform Acquisitor FPGA Programming.
a Verify the proper board is being programmed: Click Start, then right-click on My Computer and select Manage.
On the Computer Management popup, select Device Manager. In the right-hand pane, expand "Philips
Acquisition Devices" and verify that either of the following two devices are displayed:
"Philips ACQ board (1.1Gb) 4535-670-23021"
"Philips ACQ board (800Mbit) 4535-670-05131"
b Close the Computer Management window.
c Click on the AcqDiag GUI icon to start the CIRS Acquisition Board Diagnostics application.

Philips Medical Systems Confidential and Proprietary Information 8-8

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

d Click JTAG Download, to launch the JTAG Download window.

e On the JTAG Download window, click Select File.
f Navigate to the C:\ProgramFiles\Philips\CIRS\AcqGem folder
g Click the ACQ16_vxx.svf file, where xx is the version indicator.
NOTE Only one .svf file exists in the folder.
h Click Open.
i On the JTAG Download window, click OK.
NOTE If the FPGA version is already up-to-date, a dialog box will indicate that the update will not be done.
Click <OK> and skip the next step below.
j On the AcqDiagGUI window, click OK.
k On the CIRS Acquisition Board Diagnostics window, click Quit.
l Log off S1 from Remote Desktop (click Start > Log Off).
m Power off the server by depressing and holding the switch on the front of the server until the green light to the left
of the switch goes off.
NOTE The downloaded programming file for the FPGA will not take effect until the power to the board is
cycled.
n Power on the server by depressing and holding the switch on the front of the server until the green light to the left
of the switch illuminates. After the CIRS powers up, the Found New Hardware Wizard may appear. If so, select the
default "Install Automatically" option. Click Next, then Finish.
24 Perform steps to Enable Supervisor service (S1).
a Double-click the Services icon.
b Right-click on CIRS Supervisor Service.
c Select Properties.
d Change Startup type: to Automatic.
e Click OK.
f Close the Remote Desktop Connection.

Philips Medical Systems Confidential and Proprietary Information 8-9

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

25 Power off each server by depressing and holding the switch on the front of the server until the green light to the left
of the switch goes off.
26 Power on each server by depressing and holding the switch on the front of the server until the green light to the left
of the switch illuminates. The CIRS servers must be powered-on in the proper order:
— Power-on S2 and S3.
— Wait at least 3 minutes.
— Power-on S1.
27 Application software is now installed and the CIRS is operational.

Philips Medical Systems Confidential and Proprietary Information 8 - 10

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

Install Application Software on a Two Server Configuration

1 Login to the S1 server (192.168.0.200) from the Host.
a Open CIRS folder on the Host PC Desktop or Service Laptop.
b Double-click the Remote Desktop icon.
c Click OK at the Security Warning.
d At the login prompt, enter “philips_service”. For the Password, use the philips_service password.
e Click OK.
NOTE If a CIRS server is started or rebooted, you must wait at least three minutes before you can login using
Remote Desktop Connection.
2 Disable the CIRS services.
NOTE Follow Steps 2 - 11 only if you are reloading or updating application software. If this is a new install of
application software, go to Step 9 .
a Double-click the Services icon.
b Right-click on CIRS Supervisor Service.
c Select Properties.
d Change Startup type: to Disabled.
e Click OK.
f Right-click on CIRS Resource Proxy Service.
g Select Properties
h Change Startup type: to Disabled.
i Click OK.
j Right-click on CIRS Recon On/Off Service.
k Select Properties.
l Change Startup type: to Disabled.
m Click OK.
n Close the Remote Desktop Connection to S1.

Philips Medical Systems Confidential and Proprietary Information 8 - 11

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

3 Login to the S2 server (192.168.0.210) from the Host. Refer to Step 1.

4 Disable the CIRS services as described Step 2.
5 Close the Remote Desktop Connection to S2.
6 Power-off all servers.
a Power off each server by depressing and holding the switch on the front of the server until the green light to the left
of the switch goes off.
7 Power-on all servers.
a Power on each server by depressing and holding the switch on the front of the server until the green light to the
left of the switch illuminates. The CIRS servers must be powered-on in the proper order:
b Power-on S2
c Wait at least 3 minutes
d Power-on S1
NOTE You must wait at least three minutes before you can login using Remote Desktop Connection.
8 Wait at least three minutes.
9 Login to the S2 server (192.168.0.210) from the Host. Refer to Step1.
10 Install application software.
a Insert CD-ROM labeled CIRS-X.X.X.X into the CD drive of the CIRS server.
b If CD does not autoplay after inserting the disk:
— Click Start > My Computer.
— Double-click on the blue ball that says CIRS.
c At the Install CIRS software? prompt, click Yes.

Philips Medical Systems Confidential and Proprietary Information 8 - 12

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

d Click Yes to all prompts until the following prompt: CIRS Installation Complete! Choose OK to reboot the
computer. Click Cancel at this prompt.
e Remove the CIRS-X.X.X.X CD-ROM from the CD drive!
f Close the My Computer Window.
g Delete the AcqTestGUI icon.
11 Update the 3DBP device driver.
a Click Start, then right-click on My Computer.
b Select Manage.
c Click Device manager.
d Click the [+] on Philips back projection devices.
e Right-click 3DBP Backprojection board.
f Select Update driver…
g Select “Install from a list or specific location (Advanced)”.
h Click Next.
i Select “Don't search. I will choose the driver to install”
j Click Next.
k Click Have Disk…
l Enter C:\Program Files\Philips\CIRS\drivers.
m Click OK.
n Click Next.
o Click Finish.
p Close the Computer Management Window.

Philips Medical Systems Confidential and Proprietary Information 8 - 13

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

12 Update 3DBP board FPGA.

a Double-click on the 3DBP Diagnostics icon to start the CIRS 3DBP Board Diagnostics application.

b Click JTAG Download, to launch the JTAG Download window.

Philips Medical Systems Confidential and Proprietary Information 8 - 14

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

c In the JTAG Download window, click Select File.

d Navigate to the C:\ProgramFiles\Philips\CIRS\3DBP folder.
e Click the 3DBP_vxxxx.svf file, where xxxx is the version indicator.
NOTE Only one .svf file exists in the folder.
f Click Open.
g In the JTAG Download window, click OK.
NOTE If the FPGA version is already up-to-date, a dialog box will indicate that the update will not be done.
Click <OK> and skip the next step below.
h In the BpDiagGUI window, click OK.
i In the CIRS 3DBP Board Diagnostics window, click Quit.
j The downloaded programming file for the FPGA will not take effect until the power to the board is cycled.
13 Close the Remote Desktop Connection to S2.
14 Login to the S1 server (192.168.0.200) from the Host. Refer to Step 1.
15 Install application software on S1 as described in Step 10.

Philips Medical Systems Confidential and Proprietary Information 8 - 15

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

16 Update the acquisition device driver.

a Click Start, then right-click My Computer.
b Select Manage.
c Click Device manager.
d Click the [+] on Philips acquisition devices.
e Depending on the board installed, right-click on:
Philips ACQ board (1.1Gb) 4535-670-23021
Philips ACQ board (800Mbit) 4535-670-05131
Philips ACQ board (5.3Gb) 4535-670-26141
f Select Update driver…
g Select "Install from a list or specific location (Advanced)".
h Click Next.
i Select "Don't search. I will choose the driver to install".
j Click Next.
k Click Have Disk…
l Enter C:\Program Files\Philips\CIRS\drivers.
m Click OK.
n Click Next.
o Click Finish.
p Close the Computer Management Window.
17 Perform Acquisitor FPGA Programming.
a Verify the proper board is being programmed: Click Start, then right-click on My Computer and select Manage.
On the Computer Management popup, select Device Manager. In the right-hand pane, expand "Philips
Acquisition Devices" and verify that either of the following two devices are displayed:
"Philips ACQ board (1.1Gb) 4535-670-23021"
"Philips ACQ board (800Mbit) 4535-670-05131"
b Close the Computer Management window.
c Click on the AcqDiag GUI icon to start the CIRS Acquisition Board Diagnostics application.

Philips Medical Systems Confidential and Proprietary Information 8 - 16

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

d Click JTAG Download, to launch the JTAG Download window.

e On the JTAG Download window, click Select File.
f Navigate to the C:\ProgramFiles\Philips\CIRS\AcqGem folder
g Click the ACQ16_vxx.svf file, where xx is the version indicator.
NOTE Only one .svf file exists in the folder.
h Click Open.
i On the JTAG Download window, click OK.
NOTE If the FPGA version is already up-to-date, a dialog box will indicate that the update will not be done.
Click <OK> and skip the next step below.
j On the AcqDiagGUI window, click OK.
k On the CIRS Acquisition Board Diagnostics window, click Quit.
l Log off S1 from Remote Desktop (click Start > Log Off).
m Power off the server by depressing and holding the switch on the front of the server until the green light to the left
of the switch goes off.
NOTE The downloaded programming file for the FPGA will not take effect until the power to the board is
cycled.
n Power on the server by depressing and holding the switch on the front of the server until the green light to the left
of the switch illuminates. After the CIRS powers up, the Found New Hardware Wizard may appear. If so, select the
default "Install Automatically" option. Click Next, then Finish.
18 On the S1 server desktop, click on the 2-ServerCfg icon, then press <Enter>. You will see a pop-up message that
says, "Value NumberOfNodes exists, overwrite<Y/N>?” Press Y to continue.
19 Perform steps to Enable Supervisor service (S1).
a Double-click the Services icon.
b Right-click on CIRS Supervisor Service.
c Select Properties.
d Change Startup type: to Automatic.
e Click OK.
f Close the Remote Desktop Connection.

Philips Medical Systems Confidential and Proprietary Information 8 - 17

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

20 Power off each server by depressing and holding the switch on the front of the server until the green light to the left
of the switch goes off.
21 Power on each server by depressing and holding the switch on the front of the server until the green light to the left
of the switch illuminates. The CIRS servers must be powered-on in the proper order:
— Power-on S2.
— Wait at least 3 minutes.
— Power-on S1.
22 Application software is now installed and the CIRS is operational.

Philips Medical Systems Confidential and Proprietary Information 8 - 18

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

Install Application Software on a One Server Configuration

1 Login to the S1 server (192.168.0.200) from the Host.
a Open CIRS folder on the Host PC Desktop or Service Laptop.
b Double-click the Remote Desktop icon.
c Click OK at the Security Warning.
d At the login prompt, enter “philips_service”. For the Password, use the philips_service password.
e Click OK.
NOTE If a CIRS server is started or rebooted, you must wait at least three minutes before you can login using
Remote Desktop Connection.
2 Disable the CIRS services.
NOTE Follow Steps 2 - 11 only if you are reloading or updating application software. If this is a new install of
application software, go to Step 6 .
a Double-click the Services icon.
b Right-click on CIRS Supervisor Service.
c Select Properties.
d Change Startup type: to Disabled.
e Click OK.
f Right-click on CIRS Resource Proxy Service.
g Select Properties
h Change Startup type: to Disabled.
i Click OK.
j Right-click on CIRS Recon On/Off Service.
k Select Properties.
l Change Startup type: to Disabled.
m Click OK.
n Close the Remote Desktop Connection to S1.

Philips Medical Systems Confidential and Proprietary Information 8 - 19

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

3 Power-off the server by depressing and holding the switch on the front of the server until the green light to the left of
the switch goes off.
4 Power-on the server by depressing and holding the switch on the front of the server until the green light to the left of
the switch illuminates.
NOTE You must wait at least three minutes before you can login using Remote Desktop Connection.
5 Login to the S1 server (192.168.0.200) from the Host.
a Open CIRS folder on the Host PC Desktop or Service Laptop.
b Double-click the Remote Desktop icon.
c Click OK at the Security Warning.
d At the login prompt, enter “philips_service”. For the Password, use the philips_service password.
e Click OK.
6 Install application software.
a Insert CD-ROM labeled CIRS-X.X.X.X into the CD drive of the CIRS server.
b If CD does not autoplay after inserting the disk:
— Click Start > My Computer.
— Double-click on the blue ball that says CIRS.
c At the Install CIRS software? prompt, click Yes.

d Click Yes to all prompts until the following prompt: CIRS Installation Complete! Choose OK to reboot the
computer. Click Cancel at this prompt.
e Remove the CIRS-X.X.X.X CD-ROM from the CD drive!
f Close the My Computer Window.
g Delete the AcqTestGUI icon.

Philips Medical Systems Confidential and Proprietary Information 8 - 20

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

7 Wait three minutes.

8 Update the 3DBP device driver:
a Click Start, then right-click on My Computer.
b Select Manage.
c Click Device manager.
d Click the [+] on Philips back projection devices.
e Right-click 3DBP Backprojection board.
f Select Update driver…
g Select “Install from a list or specific location (Advanced)”.
h Click Next.
i Select “Don't search. I will choose the driver to install”
j Click Next.
k Click Have Disk…
l Enter C:\Program Files\Philips\CIRS\drivers.
m Click OK.
n Click Next.
o Click Finish.
p Close the Computer Management Window.

Philips Medical Systems Confidential and Proprietary Information 8 - 21

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

9 Update 3DBP board FPGA.

a Double-click on the 3DBP Diagnostics icon to start the CIRS 3DBP Board Diagnostics application

b Click JTAG Download, to launch the JTAG Download window.

Philips Medical Systems Confidential and Proprietary Information 8 - 22

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

c In the JTAG Download window, click Select File.

d Navigate to the C:\ProgramFiles\Philips\CIRS\3DBP folder.
e Click the 3DBP_vxxxx.svf file, where xxxx is the version indicator.
NOTE Only one .svf file exists in the folder.
f Click Open.
g In the JTAG Download window, click OK.
NOTE If the FPGA version is already up-to-date, a dialog box will indicate that the update will not be done.
Click <OK> and skip the next step below.
h In the BpDiagGUI window, click OK.
i In the CIRS 3DBP Board Diagnostics window, click Quit.
j The downloaded programming file for the FPGA will not take effect until the power to the board is cycled.
10 Update the acquisition device driver.
a Click Start, then right-click My Computer.
b Select Manage.
c Click Device manager.

Philips Medical Systems Confidential and Proprietary Information 8 - 23

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

d Click the [+] on Philips acquisition devices.

e Depending on the board installed, right-click on:
Philips ACQ board (1.1Gb) 4535-670-23021
Philips ACQ board (800Mbit) 4535-670-05131
Philips ACQ board (5.3Gb) 4535-670-26141
f Select Update driver…
g Select "Install from a list or specific location (Advanced)".
h Click Next.
i Select "Don't search. I will choose the driver to install".
j Click Next.
k Click Have Disk…
l Enter C:\Program Files\Philips\CIRS\drivers.
m Click OK.
n Click Next.
o Click Finish.
p Close the Computer Management Window.
11 Perform Acquisitor FPGA Programming.
a Verify the proper board is being programmed: Click Start, then right-click on My Computer and select Manage.
On the Computer Management popup, select Device Manager. In the right-hand pane, expand "Philips
Acquisition Devices" and verify that either of the following two devices are displayed:
"Philips ACQ board (1.1Gb) 4535-670-23021"
"Philips ACQ board (800Mbit) 4535-670-05131"
b Close the Computer Management window.
c Click on the AcqDiag GUI icon to start the CIRS Acquisition Board Diagnostics application.
d Click JTAG Download, to launch the JTAG Download window.
e On the JTAG Download window, click Select File.
f Navigate to the C:\ProgramFiles\Philips\CIRS\AcqGem folder.
g Click the ACQ16_vxx.svf file, where xx is the version indicator.

Philips Medical Systems Confidential and Proprietary Information 8 - 24

Brilliance CT Software Installation Manual Version 1.2 CIRS Application Software Installation

NOTE Only one .svf file exists in the folder.

h Click Open.
i On the JTAG Download window, click OK.
NOTE If the FPGA version is already up-to-date, a dialog box will indicate that the update will not be done.
Click <OK> and skip the next step below.
j On the AcqDiagGUI window, click OK.
k On the CIRS Acquisition Board Diagnostics window, click Quit.
l Log off S1 from Remote Desktop (click Start > Log Off).
m Power off the server by depressing and holding the switch on the front of the server until the green light to the left
of the switch goes off.
NOTE The downloaded programming file for the FPGA will not take effect until the power to the board is
cycled.
n Power on the server by depressing and holding the switch on the front of the server until the green light to the left
of the switch illuminates. After the CIRS powers up, the Found New Hardware Wizard may appear. If so, select the
default "Install Automatically" option. Click Next, then Finish.
12 On the S1 server desktop, click on the 1-ServerCfg icon, then press <Enter>. You will see a pop-up message that
says, "Value NumberOfNodes exists, overwrite<Y/N>?” Press Y to continue.
13 Perform steps to Enable Supervisor service (S1).
a Double-click the Services icon.
b Right-click on CIRS Supervisor Service.
c Select Properties.
d Change Startup type: to Automatic.
e Click OK.
f Close the Remote Desktop Connection.
14 Power off S1 by depressing and holding the switch on the front of the server until the green light to the left of the
switch goes off.
15 Power on S1 by depressing and holding the switch on the front of the server until the green light to the left of the
switch illuminates.
16 Application software is now installed and the CIRS is operational.

Philips Medical Systems Confidential and Proprietary Information 8 - 25

Brilliance CT Software Installation Manual Version 1.2 System Calibration

System Calibration

NOTE If you are reinstalling the same Brilliance CT version on a system that was calibrated using that same
version, and you have a good site backup EOD, you do not need to recalibrate. Calibrations should be
restored even if re-running full calibrations after installation. Run Air Calibration and HCOR Calibration
by following the procedures in the Brilliance CT Calibration Manual.
NOTE Full calibrations are required when upgrading from Brilliance 16P 1.0 to any version of Brilliance CT
1.2. Also, full calibrations are required when installing a new system. Otherwise, calibrations are not
required but they are recommended.

1 Login to the system as philips_service and start the Scanner Application.

2 Click on Home > Utilities > Calibration > Selective Calibration.
3 Select Auto Calibration Reasons and click Start Calibration.
4 In the Image Calibrations Selector Window, click Reasons > New System Installation.
NOTE This will automatically enable Automatic Mode.
5 Click Start Calibrations.
6 Follow the advice given by the Selective Calibration application.
7 In the Image Calibrations Selector Window, When calibration is complete, backup the installation:
a Insert a formatted EOD onto the drive.
b Double-click on the Backup_Restore Icon on the desktop.
c Click Browse to choose the location of the backup.
d Choose drive F:.
e Click OK.
f Click Start Backup.
g When complete, click OK, then click Close, and Exit the backup program.

Philips Medical Systems Confidential and Proprietary Information 9-1

Brilliance CT Software Installation Manual Version 1.2 Appendix A - Instructions to set Host PC BIOS

Appendix A - Instructions to set Host PC BIOS

1 Restart the system:

a If you are logged into the system: Select Start > Shut down..., then select Shut down from the drop-down list,
and click OK.
a If you are not logged in, press <Ctrl><Alt><Del> on he keyboard, then click on the Shut Down… button, select
Shutdown and Restart, and click OK.
2 When the F2=Setup message appears in the upper right hand corner, press <F2>.
3 In setup, use the Down arrow key to scroll to Boot Sequence, and then press <Enter>.
4 Verify that the IDE CD-ROM device is before the hard disk in the boot sequence list. If not, adjust it using the
directions on the screen.
5 Press <Enter> to dismiss the Boot Sequence list, and <Esc> to exit setup.
6 If prompted, select Save Changes and Exit. Press <Enter> to leave Setup mode.

Philips Medical Systems Confidential and Proprietary Information A-1

Brilliance CT Software Installation Manual Version 1.2 Appendix B - Re-install Brilliance CT Miscellaneous Component

Appendix B - Re-install Brilliance CT Miscellaneous Component

1 Make sure you are logged in as philips_service.
2 Click Start > Run.
3 Type regedit and click OK.
4 Navigate to HKEY_LOCAL_MACHINE/SOFTWARE/Philips/Setup/Installed.
5 Right-click on Brilliance CT Miscellaneous, and select Delete from the popup menu.
6 Click Yes to confirm.
7 Close all windows.
8 Click Start > Control Panel.
9 If not in Classic View, switch to Classic View.
10 Double-click Add or Remove Programs.
11 Select Brilliance CT Miscellaneous and click Remove.
12 Click Yes to confirm.
13 Close all windows.
14 Insert the Host Applications CD into the CD/DVD ROM drive of the HOST PC.
15 Double-click My Computer.
16 Double-click the E: drive.
17 Double-click Setup.
18 Click Start.
NOTE No need to change username or password
NOTE Do not touch the keyboard or mouse until install is complete.
19 When the "Installation completed" message appears at the bottom of the "Philips Install Supervisor" window, scroll
through the Install Supervisor and ensure that the Brilliance CT Miscellaneous Component is "Done, (exit code:
0x00000000)". Then click Close in the window.
NOTE If the Brilliance CT Miscellaneous Component is not "Done, (exit code: 0x00000000)", then go back to
step 1 and reinstall the Brilliance CT Miscellaneous Component.
20 Remove the CD from the drive.

Philips Medical Systems Confidential and Proprietary Information B-1

Brilliance CT Software Installation Manual Version 1.2 Appendix C - Server Setup Instructions

Appendix C - Server Setup Instructions

1 Insert CD labeled "Intel Server Board SE7501BR2 for S1 or SE7501WV2 for S2/S3 Resource CD" (if it is available)
into CD-ROM and boot from it.
a Click Continue at the Welcome Screen.
b Click on Continue.
c Select Server Configuration Utilities.
d Select Run System Setup.
2 If no CD is available, boot to the Service Partition (F4 option during boot up), change directory (cd) to C:\SSU, and
type ssu.
3 “System Setup v2.2” flashes across the screen.
4 Scroll to PEM (Platform Event Management) on the left-hand side of the screen.
5 Select the Configure LAN button.
6 Check the Enable LAN Alerts box.
7 Leave the password box empty.
8 Set LAN Access to Always Available.
9 Make sure that SNMP Community is labeled Public.
10 Set IP Setup to Static.
11 For the Host IP Address: enter 192.168.0.150 for S1, enter 192.168.0.151 for S2, enter 192.168.0.152 for S3.
12 Set the Gateway address to 0.0.0.0.
13 For the Subnet Mask, enter 255.255.255.0.
14 Make sure Alert IP Address1 and Alert IP Address2 are both blank.
15 Click on Save.
16 Select the Options submenu and click on Configure Serial Over LAN.
17 Set the baud rate to 19.2.
18 Select Always Available.
19 Click Save.

Philips Medical Systems Confidential and Proprietary Information C-1

Brilliance CT Software Installation Manual Version 1.2 Appendix C - Server Setup Instructions

20 Click Close.
21 Click OK at the screen where a MAC address error is mentioned.
22 Click Close.
23 Click File, then Exit.
24 Click OK.
25 Remove the CD from the server.
26 Reboot.

Philips Medical Systems Confidential and Proprietary Information C-2

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

Appendix D - Update BIOS Setting for CIRS Servers

Check BIOS Versions

NOTE The minimal required version of BIOS/BMC/FRU/SDR should be as following:

Server BIOS BMC FRU/SDR What actually appears:

S1 (SE7501BR2) P15-0074 1.18 5.6.I or 5.5.I SBR20.86B.0074.P15
S2/S3 (SE7501WV2) P16-0190 1.19 5.6.A SWVR25.86B.0190.P16

NOTE BIOS Setup could be done by console redirection through either IPMI hyper terminal telnet session or
DPC Console (see the CIRS Service Manual section “Tools for Advanced Server’s Diagnostic” for tools
description). You can also attach a monitor, keyboard, and mouse directly to the servers.

To check the current version:

1 Go into BIOS Setup (by pressing F2 at boot up).
2 On the BIOS menu, select Server > System Management.
3 If the version does not meet the requirement, then follow the BIOS Update Instructions starting on the next page. If
the version does meet the requirement, continue with CIRS Application Software Installation.

Philips Medical Systems Confidential and Proprietary Information D-1

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

BIOS Update Instructions

NOTE BIOS Setup could be done by console redirection through either IPMI hyper terminal telnet session or
DPC Console (see the CIRS Service Manual section “Tools for Advanced Server’s Diagnostic” for tools
description). You can also attach a monitor, keyboard, and mouse directly to the servers.

Use Granite CD labeled “PHILIPS, System Diagnostic Utilities, Part Number: SOFGR-064, Revision:009, Disk 1 of 1”.
This should be done on ALL SERVERS (S1, S2, S3).

S1 Server
1 Carefully slide the S1 server out from the rack. Please pay attention to the cabling at the back of the server, ensure
that no interference is encountered.
2 Turn the server off and remove the power plug to the server.
3 Remove the cover to the server.
4 Set BMC Boot Block Write Enable Jumper to the "enable" position as indicated on the following figure. Make sure to
change it back to the "disable" position after BIOS update is completed.

Philips Medical Systems Confidential and Proprietary Information D-2

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

Figure D - 1: BMC Boot Block Write Enable Jumper setting for S1 Server
5 Reinsert the power connector to the server and start the server.

Philips Medical Systems Confidential and Proprietary Information D-3

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

6 Insert CD into CD-ROM drive and reboot the Server (if you're using SOL, follow the instructions in the CIRS Service
Manual (IPMI BIOS SETUP).
NOTE If using SOL, communication with the Server will be lost at the point when BMC gets updated. When
this happens, wait about 10 minutes to let the update complete, then reboot the Server, press F2 to go
to the BIOS setup and verify that BIOS/BMC/SDR/FRU have been set to the required version.
7 When Server boots from CD the following menu comes up:

8 Select option 2 (BIOS Update) to update the BIOS.

Philips Medical Systems Confidential and Proprietary Information D-4

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

9 Answer “Y” at the following screen and BIOS update would start.
NOTE You have just 10 seconds to respond.

10 You will see numerous updates relating to uploading, etc. After a period of time, a red window will popup stating that
the BIOS will now be written. DO NOT do anything with the S1 server during this time. Once this gets done another
red window will popup to do another write. Once again, DO NOT do anything with the S1 server during this time.
Once completed, the screen will display a J: prompt.
11 Eject the CD from the drive.
12 Restart the computer, enter BIOS setup, and verify that the version is at the required level. Refer to Check BIOS
Versions.
13 Remove power to the server and move the J1J1 jumper to its original position.
14 Replace the cover removed earlier and carefully push to server back into the rack ensuring that no cable interference
is encountered.

Philips Medical Systems Confidential and Proprietary Information D-5

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

S2 Server
1 Carefully slide the S2 server out from the rack. Please pay attention to the cabling at the back of the server, ensure
that no interference is encountered.
2 Turn the server off and remove the power plug to the server.
3 Remove the cover to the server.
4 Set BMC Boot Block Write Enable Jumper (J4B2) to the "enable" position as indicated on the figure below. Make
sure to change it back to the "disable" position after BIOS update is completed.
NOTE The jumper is located immediately next to the PCIx connector where the 3DBP riser is plugged.

Philips Medical Systems Confidential and Proprietary Information D-6

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

Figure D - 2: BMC Boot Block Write Enable Jumper setting for S2/S3 Servers

Philips Medical Systems Confidential and Proprietary Information D-7

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

5 Carefully raise the 3DBP riser assembly from the rear.

6 Once the riser is disengaged from the server's motherboard, remove the power connection(s) to the power board.
For a single 3DBP and a single-channel Power Module, the connection is on ST3 and for a dual 3DBP and a dual-
channel Power Module the connections are ST2 and ST3.

Philips Medical Systems Confidential and Proprietary Information D-8

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

7 Place the assembly onto an anti-static mat.

8 Replace the power connector and power the unit up.
NOTE If during the boot process an error message in red appears stating:
8140 Processor 01 Failed FRB Level 3 Times
8140 Processor 02 Failed FRB Level 3 Times
8130 Processor 02 Disabled
F1 to resume
Please press the control alt delete simultaneously to restart the computer. Press F2 during boot up to access the
BIOS menu. In the Main section use the down arrow key until the Processor Settings is highlighted and press enter.
On the subsequent page, use the down arrow key until the Processor Retest is highlighted. Hit enter and change the
setting to Enabled. Save the settings, insert the CD and let the system restart.

Philips Medical Systems Confidential and Proprietary Information D-9

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

9 Insert CD into CD-ROM drive and reboot the Server (if you're using SOL, follow the instructions in the CIRS Service
Manual (IPMI BIOS SETUP).
NOTE If using SOL, communication with the Server will be lost at the point when BMC gets updated. When
this happens, wait about 10 minutes to let the update complete, then reboot the Server, press F2 to go
to the BIOS setup and verify that BIOS/BMC/SDR/FRU have been set to the required version.
10 When Server boots from CD the following menu comes up:

11 Select option 2 (BIOS Update) to update the BIOS.

Philips Medical Systems Confidential and Proprietary Information D - 10

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

12 Answer “Y” at the following screen and BIOS update would start.
NOTE You have just 10 seconds to respond.

13 You will see numerous updates relating to uploading, etc. After a period of time, a red window will popup stating that
the BIOS will now be written. DO NOT do anything with the S1 server during this time. Once this gets done another
red window will popup to do another write. Once again, DO NOT do anything with the S1 server during this time.
Once completed, the screen will display a J: prompt.
14 Eject the CD from the drive.
15 Restart the computer, enter BIOS setup, and verify that the version is at the required level. Refer to Check BIOS
Versions.
16 Remove power to the server and remove the power connector.
17 Move the J4B2 jumper to its original position.

Philips Medical Systems Confidential and Proprietary Information D - 11

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

18 ·Insert the power supply harness connectors into the sockets on the Power Module card of the 3DBP riser assembly.
For the dual 3DBP and a dual-channel Power Module, the end connector of the harness, P6, must be inserted in the
ST2 (lower) socket. P7 is inserted in the ST3 (upper) socket. In the case of a single 3DBP and a single-channel
Power Module, connect the end connector of the power wiring harness, P6, to the power input connector (ST3).

19 ·The use of long nose pliers (vice-grip pliers work nicely) is recommended to insert the plugs into the sockets. Gently
apply pressure to the ends of the plug/socket pair, going back and forth several times to reach the fully-seated
position.
20 Angle the assembly into position, and engage the retainer bracket of the top board into the top card guide.

Philips Medical Systems Confidential and Proprietary Information D - 12

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

Philips Medical Systems Confidential and Proprietary Information D - 13

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

Philips Medical Systems Confidential and Proprietary Information D - 14

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

21 As the rear of the assembly is lowered into position, make sure that each of the retainer brackets engages its
corresponding card guide. You may have to position the retainer brackets with a screwdriver or similar object to
insure that they engage the card guides as the riser assembly is lowered into position. Also make sure that the
plenum piece is positioned between the riser PCB and the riser sheet metal component.

Philips Medical Systems Confidential and Proprietary Information D - 15

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

22 As the riser is lowered into position, the rear of the riser assembly fits inside the rear of the chassis

Philips Medical Systems Confidential and Proprietary Information D - 16

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

23 Make sure the riser card is aligned with the PCI slot on the motherboard.

24 Note that the lower lip of the riser assembly fits on the outside of the chassis rear frame.

Philips Medical Systems Confidential and Proprietary Information D - 17

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

25 When fully lowered into position, check that the retainer brackets of both the 3DBP(s) and the Power Module are
inserted in their respective card guides.

Philips Medical Systems Confidential and Proprietary Information D - 18

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

26 For two 3DBPs, it will look like this. It is imperative that all of the card guides are properly engaged. This is necessary
to maintain the proper separation of the cards within the riser assembly.
27 Replace the cover removed earlier and carefully push to server back into the rack ensuring that no cable interference
is encountered.
28 Reinsert the power connector to the server.

Philips Medical Systems Confidential and Proprietary Information D - 19

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

S3 Server
29 Carefully slide the S2 server out from the rack. Please pay attention to the cabling at the back of the server, ensure
that no interference is encountered.
30 Turn the server off and remove the power plug to the server.
31 Remove the cover to the server.
32 Set BMC Boot Block Write Enable Jumper (J4B2) to the "enable" position as indicated on the figure below. Make
sure to change it back to the "disable" position after BIOS update is completed.
NOTE The jumper is located immediately next to the PCIx connector. It may be necessary to remove the
empty riser assembly.

Philips Medical Systems Confidential and Proprietary Information D - 20

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

Figure D - 3: BMC Boot Block Write Enable Jumper setting for S2/S3 Servers

Philips Medical Systems Confidential and Proprietary Information D - 21

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

33 Replace the power connector and power the unit up.

NOTE If during the boot process an error message in red appears stating:
8140 Processor 01 Failed FRB Level 3 Times
8140 Processor 02 Failed FRB Level 3 Times
8130 Processor 02 Disabled
F1 to resume
Please press the control alt delete simultaneously to restart the computer. Press F2 during boot up to access the
BIOS menu. In the Main section use the down arrow key until the Processor Settings is highlighted and press enter.
On the subsequent page, use the down arrow key until the Processor Retest is highlighted. Hit enter and change the
setting to Enabled. Save the settings, insert the CD and let the system restart.
34 Insert CD into CD-ROM drive and reboot the Server (if you're using SOL, follow the instructions in the CIRS Service
Manual (IPMI BIOS SETUP).
NOTE If using SOL, communication with the Server will be lost at the point when BMC gets updated. When
this happens, wait about 10 minutes to let the update complete, then reboot the Server, press F2 to go
to the BIOS setup and verify that BIOS/BMC/SDR/FRU have been set to the required version.
35 When Server boots from CD the following menu comes up:

Philips Medical Systems Confidential and Proprietary Information D - 22

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

36 Select option 2 (BIOS Update) to update the BIOS.

Philips Medical Systems Confidential and Proprietary Information D - 23

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

37 Answer “Y” at the following screen and BIOS update would start.
NOTE You have just 10 seconds to respond.

38 You will see numerous updates relating to uploading, etc. After a period of time, a red window will popup stating that
the BIOS will now be written. DO NOT do anything with the S1 server during this time. Once this gets done another
red window will popup to do another write. Once again, DO NOT do anything with the S1 server during this time.
Once completed, the screen will display a J: prompt.
39 Eject the CD from the drive.
40 Restart the computer, enter BIOS setup, and verify that the version is at the required level. Refer to Check BIOS
Versions.
41 Remove power to the server and remove the power connector.
42 Move the J4B2 jumper to its original position.
43 Replace the cover removed earlier and carefully push to server back into the rack ensuring that no cable interference
is encountered.
44 Reinsert the power connector to the server.

Philips Medical Systems Confidential and Proprietary Information D - 24

Brilliance CT Software Installation Manual Version 1.2 Appendix D - Update BIOS Setting for CIRS Servers

Conclusion
1 Apply power to the S3 server and then S2. Wait for at least 3 minutes and then apply power to S1.
2 Complete a Functional Scan to ensure that the unit is fully operational.
3 Return to CIRS OS Installation to complete the OS installation, followed by the CIRS Application Software
installation.

Philips Medical Systems Confidential and Proprietary Information D - 25