h

c
rd
F
s
n
m
ie
S

SIREMOBIL
SP

Installation Instructions
Option

18" TFT Display 8079530

© Siemens, 2004

07539005

© Siemens, 2004
All documents may only be used for rendering
services on Siemens Healthcare Products. Any
document in electronic form may be printed
once. Copy and distribution of electronic docu-
ments and hardcopies is prohibited. Offenders
will be liable for damages. All other rights are re-
served.

Print No.: SPR2-230.812.02.03.02 English

Replaces: SPR2-230.812.02.02.02 Doc. Gen. Date: 10.08
CS PS SP
n.a.

2004
2 Copyright / Version / Disclaimer
1Copyright / Version / Disclaimer

Copyright
“© Siemens, 2004“ refers to the copyright of a Siemens entity such as Siemens Aktienge-
sellschaft - Germany, Siemens Mindit Magnetic Resonance Ltd. - China, Siemens Shang-
hai Medical Equipment Ltd. - China, Siemens Medical Solutions USA Inc. - USA and/or
Siemens Healthcare Diagnostics Inc. - USA.

Document Version
Siemens reserves the right to change its products and services at any time.
In addition, manuals are subject to change without notice. The hardcopy documents corre-
spond to the version at the time of system delivery and/or printout. Versions to hardcopy
documentation are not automatically distributed. Please contact your local Siemens office
to order current version or refer to our website http://www.healthcare.siemens.com.

Disclaimer
Siemens provides this documentation “as is“ without the assumption of any liability under
any theory of law.
The installation and service of equipment described herein requires superior understand-
ing of our equipment and may only be performed by qualified personnel who are specially
trained for such installation and/or service.

SIREMOBIL SPR2-230.812.02.03.02 Page 2 of 26 © Siemens, 2004

10.08 CS PS SP
Table of Contents 3
0Table of Contents

1 _______ General information______________________________________________ 4

Notes and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
General safety information (in existing documents) . . . . . . . . . . . . . . . . . . . . . . . . . . 5
General electrical safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Validity of these instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Required Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Required Tools, Test Equipment and Aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Required Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2 _______ Installation of conversion set 7141380 (1 monitor) ___________________ 10

Dismantling the existing monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installing the TFT display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3 _______ Installation of conversion set 7141125 (2 monitors) __________________ 14

Dismantling the existing monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Installing the support arm to the monitor cart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Installing the TFT display on the support arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Adjusting the support arm to the size of the TFT display . . . . . . . . . . . . . . . . . . . . . 18
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Protective ground wiring of the support arm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Wiring the radiation indicators of the support arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Wiring of the displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Running the cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4 _______ Adjustments ___________________________________________________ 23

TFT display BARCO MVGD 1318, part number 80 79 530 . . . . . . . . . . . . . . . . . . . . . . 23

Final work steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

5 _______ Changes to Previous Version _____________________________________ 25

© Siemens, 2004 SPR2-230.812.02.03.02 Page 3 of 26 SIREMOBIL

10.08 CS PS SP
4 General information
1-
Notes and symbols
1General information

Bolded text in this documentation means the following:

Tab. 1 GEFAHR / DANGER

Bei einer unmittelbar drohenden Gefahr, die bei Nichtvermeidung

zum Tod oder zu einer schweren Körperverletzung führt.

Indicates when there is an immediate danger that leads to death

or serious physical injury.

Tab. 2 WARNUNG / WARNING

Bei einer Gefahr, die bei Nichtvermeidung zum Tod oder zu einer
schweren Körperverletzung führen kann.

Indicates a risk of danger that may lead to death or serious phys-

ical injury.

Tab. 3 VORSICHT / CAUTION

Bei einer Gefahr, die bei Nichtvermeidung zu einer leichten oder

mittleren Körperverletzung und/ oder zu einer Sachbeschädigung
führt oder führen kann.
Indicates a risk of danger that leads to slight or moderate physical
injury and/or damage to property.

Tab. 4 ACHTUNG / NOTICE

Bei einer Gefahr, die bei Nichtvermeidung zu einem unerwünscht-

en Ergebnis oder Zustand führt oder führen kann (nicht Tod,
Körperverletzung oder Sachbeschädigung).
Indicates a risk of danger that if disregarded leads or may lead to
a potential situation which may result in an undesirable result or
state (not death, physical injury or property damage).

Tab. 5 HINWEIS / NOTE

Ist als Tipp zu verstehen. Der Anwender muss diese Anweisung

nicht unbedingt beachten. Er erfährt jedoch Vorteile, wenn er dies
tut.
Should be understood as a tip. The user does not absolutely have
to observe these instructions. However, there will be advantages
if he does.

SIREMOBIL SPR2-230.812.02.03.02 Page 4 of 26 © Siemens, 2004

10.08 CS PS SP
General information 5

Safety instructions 1.1

General safety information (in existing documents) 0

WARNING Danger of injury, death, or material damage.

Non-compliance can lead to death, injury, or material dam-
age.

Please note:
¹ The product-specific safety information in these
instructions,
¹ The general safety information in TD00-000.860.01...,
and
¹ The safety information in accordance with ARTD Part 2.

General electrical safety information 0

WARNING Electrical safety!

Non-compliance can lead to severe injury or even death, as
well as material damage.
¹ Parts under an electrical charge are accessible when
the covers are open. To avoid danger, disconnect the
system from the power supply before opening the cov-
ers. Disconnect the power plug.
¹ If an uninterruptible power supply (UPS) is installed in
the system, the voltage output of the UPS must also be
deenergized or the voltage output plug must be discon-
nected.
¹ If work steps must be performed using electrical
power, the general safety information according to
TD00-000.860.01... must be observed.

© Siemens, 2004 SPR2-230.812.02.03.02 Page 5 of 26 SIREMOBIL

10.08 CS PS SP
6 General information

Validity of these instructions 1.2

These instructions are valid for the conversion of a SIREMOBIL Compact, SIREMOBIL
Compact L, SIREMOBIL Iso-C, ARCOSKOP or POWERMOBIL from 17" tube monitors
(mounted to a monitor cart) to 18" TFT displays (8079530).

NOTE Two upgrade kits are available, one for systems with one
monitor (material number 7141380) and one for systems with
two monitors (material number 7141125). These instructions
are valid for both upgrade kits.

SIREMOBIL SPR2-230.812.02.03.02 Page 6 of 26 © Siemens, 2004

10.08 CS PS SP
General information 7

Required Parts 1.3

Monitor upgrade kit for systems with one monitor, material number 7141380

or

Monitor upgrade kit for systems with two monitors, material number 7141125

© Siemens, 2004 SPR2-230.812.02.03.02 Page 7 of 26 SIREMOBIL

10.08 CS PS SP
8 General information

Required Tools, Test Equipment and Aids 1.4

NOTE All tools, measuring equipment and aids, with the exception
of those marked with "*", are listed and specified in the SPC
(Spare Parts Catalog).

• Standard toolkit*
• Set of Allen wrenches*
• Protective conductor test device, e.g. UNIMET 1100 ST 51 38 727
• Luminence measuring device, e.g., SMFit spotmeter 77 52 848
• Low-solid screw locking element, e.g. Loctite 221 20 48 874

Plus for the IQ Quick Test:

• Set of X-ray filters, 10 x 0.3 mm Cu 44 06 120
• Precision X-ray filter, 2.1 mm Cu 99 00 598
• 25 mm AL measuring stand, type 26765 acc. to DIN 6868
Part 50
or 97 98 596 and
1.2 mm Cu from the X-ray filter set 11 67 662
17 µm Cu strips
• Resolution test set 28 71 820
Factory: Resolution test, type 41a
• Dynamic test case 37 90 156
or 97 50 001
containing: TV dynamic test 37 90 164
Heart contour diaphragm 37 90 172
Capillary test 37 90 180
Mount 87 13 901
Veiling glare 87 09 743
test
• Service PC *
• Service software system (see logbook)
• Serial interface cable for service PC - Host 99 00 440

SIREMOBIL SPR2-230.812.02.03.02 Page 8 of 26 © Siemens, 2004

10.08 CS PS SP
General information 9

Required Documents 1.5

NOTE The corresponding replacement instructions are necessary

for checking and if necessary adjusting the new TFT dis-
plays.

• Replacement instructions '18” B/W TFT monitor MVGD 1318' TD00-000.841.17...

• System binder / system logbook
• IQ quick test of the system

© Siemens, 2004 SPR2-230.812.02.03.02 Page 9 of 26 SIREMOBIL

10.08 CS PS SP
10 Installation of conversion set 7141380 (1 monitor)
2-
Dismantling the existing monitor
2Installation of conversion set 7141380 (1 monitor)

NOTE For installation of the conversion set 7141125 (systems with

two monitors) refer to chapter (Installation of conversion set
7141125 (2 monitors) / p. 14).

• Remove the monitor cover (Fig. 1 / p. 10) and unplug all cables from the monitor to be
replaced.
Only for SIMOMED N monitor 1102628: Remove the shield plate (Fig. 2 / p. 10) and the
connection housing (Fig. 3 / p. 10).

Fig. 1: Monitor cover_2 Fig. 2: Shielding plate_2

• Loosen the 2 screws at the monitor mounting.(Fig. 4 / p. 10)

Fig. 3: Connection housing_1 Fig. 4: Monitor mounting_1

• Lift down the monitor.

SIREMOBIL SPR2-230.812.02.03.02 Page 10 of 26 © Siemens, 2004

10.08 CS PS SP
Installation of conversion set 7141380 (1 monitor) 11

• Unscrew the base of the monitor (Fig. 5 / p. 11) from the monitor cart and remove com-
pletely (Fig. 6 / p. 11).

Fig. 5: Monitor base_1 Fig. 6: Cable bush_1

• Completely remove the video cable.

• Completely remove and disconnect the power cable.

© Siemens, 2004 SPR2-230.812.02.03.02 Page 11 of 26 SIREMOBIL

10.08 CS PS SP
12 Installation of conversion set 7141380 (1 monitor)

Installing the TFT display 2.1

• Screw the new display bracket onto the monitor cart using 4 countersunk screws M6 x
16, 4 washers and 4 nuts (included in the conversion set) (1/Fig. 7 / p. 12).

Fig. 7: Display mount

Fig. 8: ON/OFF assembly

• Run the free cord end of the new power cord down through the display bracket and
sideways through the rail to the ON/OFF assembly and connect to the terminal strip
(Fig. 8 / p. 12)
- Connect the brown cable ends to terminal block X2.1.
- Connect the blue cable ends to terminal block X2.2.
- Connect the protective conductor (green-yellow) to the ground terminal.
• Run the new BNC video cable with the insulated end down through the display bracket
and sideways through the rail to the Memoskop. Plug the cord to bushing OUT1 and
latch.

NOTE The end with the open shielding braid must be on the display
side (Fig. 10 / p. 12).

Fig. 10: video cable_1

Fig. 9: Protective wire connection

SIREMOBIL SPR2-230.812.02.03.02 Page 12 of 26 © Siemens, 2004

10.08 CS PS SP
Installation of conversion set 7141380 (1 monitor) 13

• Connect the ground wire received in the scope of delivery to the display bracket (nut
and washer included in conversion kit) (2/Fig. 7 / p. 12). Run the other end down
through the display bracket and connect to the ground wire connection in the log book
compartment (Fig. 9 / p. 12).
• Tightly screw the display to the display bracket with 4 countersunk screws M4 x 12
(contained in the scope of delivery) using a low-solid screw locking element (e.g. Loc-
tite 221) (1/Fig. 11 / p. 13).
Make sure that the cords lie between the spacers of the display bracket
(3/Fig. 7 / p. 12).

Fig. 11: Display

• Open the rear cover of the display.
• Connect the video cable to the BNC socket VIDEO of the display and lock it.
• Connect the shielding of the video cable to the ground of the display.
• Plug the power cord to the display.
• Reinstall the cover on the display.
• Pull back the power cord and video cable as needed into the monitor cart
(Fig. 11 / p. 13).

NOTE Continue with chapter (Adjustments / p. 23).

© Siemens, 2004 SPR2-230.812.02.03.02 Page 13 of 26 SIREMOBIL

10.08 CS PS SP
14 Installation of conversion set 7141125 (2 monitors)
3-
Dismantling the existing monitors
3Installation of conversion set 7141125 (2 monitors)

• Remove the monitor covers (Fig. 12 / p. 14) and unplug all cables from the monitors to
be replaced.
Only for SIMOMED N monitor 11 02 628: Remove the shield plates (Fig. 13 / p. 14) and
the connection housings (Fig. 14 / p. 14).

Fig. 12: Monitor cover Fig. 13: Shielding plate

• Loosen the 2 screws at each of the monitor mountings.(Fig. 15 / p. 14)

Fig. 14: Connection housing Fig. 15: Monitor attachment

• Lift down both monitors.

SIREMOBIL SPR2-230.812.02.03.02 Page 14 of 26 © Siemens, 2004

10.08 CS PS SP
Installation of conversion set 7141125 (2 monitors) 15

• Reattach all previously removed parts to the monitor.

Fig. 16: Monitor attachments Fig. 17: Monitor cart cable bushes

• Unscrew both bases of the monitors from the monitor cart and remove completely
(Fig. 16 / p. 15).
• Remove the two video cables.

NOTE Only for SIREMOBIL Iso-C 3D:

The 3 line video cable from the right monitor (green, blue,
red) will be reused. Therefore, do not completely remove the
video cable; instead only pull it through the cable bushes
into the log book compartment.

• Completely remove and disconnect the two power cables.

• 4 prepunched holes are visible around the central cable bush (Arrows/Fig. 16 / p. 15).
4 metal bolts are inserted in these holes and they are thus closed. Drive out the 4 metal
bolts downwards with a drift (or another round object). Remove the 4 metal bolts from
the monitor cart.
• Lift off the central blind cover and close one of the cable bushes on the side with it
(Fig. 17 / p. 15).
• Close off the 2nd cable bush on the side and the 8 fastening holes around the cable
bushes on the sides with the enclosed blind covers.

© Siemens, 2004 SPR2-230.812.02.03.02 Page 15 of 26 SIREMOBIL

10.08 CS PS SP
16 Installation of conversion set 7141125 (2 monitors)

Installing the support arm to the monitor cart 3.1

Fig. 18: ON/OFF assembly Fig. 19: Installation of the support arm

• Screw the adapter plate (1/Fig. 19 / p. 16) to the support arm base using 4 screws M6 x
10 (included in the scope of delivery) and Loctite 221.
• Open the rear cover of the support arm base.
• Run the stripped cord end of the new power cords (included in the scope of delivery)
down through the bracket of the support arm (2/Fig. 19 / p. 16) and the cable bush of
the support arm base (1/Fig. 19 / p. 16), on through the center cable bush of the moni-
tor cart and sideways through the rail to the ON/OFF (Fig. 18 / p. 16) assembly and
connect to the terminal block:
- Connect the brown cable ends to terminal block X2.1.
- Connect the blue cable ends to terminal block X2.2.
- Connect the protective conductor (green-yellow) to the ground terminal
(1/Fig. 18 / p. 16).

NOTE The new power line cables have a length of approx. 2.6 m and
are equipped with a straight IEC connector on one cable end.

• Run the video cable included in the scope of delivery (BNC plug - BNC plug) with the
insulated end towards the bottom through the center cable bush of the monitor cart,
sideways through the lateral rail to the MEMOSKOP. Plug in and lock the cables at the
OUT1 socket (left display) and OUT2 socket (right display).

NOTE Only for SIREMOBIL Iso-C 3D:

Only one new video cable is needed for the left display. The
available 3 line video cable is reused for the right display.

SIREMOBIL SPR2-230.812.02.03.02 Page 16 of 26 © Siemens, 2004

10.08 CS PS SP
Installation of conversion set 7141125 (2 monitors) 17

NOTE The end of the new video cable with the open shielding braid
(Fig. 20 / p. 17) must be on the display side.

Fig. 20: video cable_1

• Thread the video cable upwards, through the rectangular cable bush (1/Fig. 19 / p. 16)
of the support arm base and on through the bracket of the support arm
(2/Fig. 19 / p. 16).
• Place the support arm base above the center cable bush (Fig. 19 / p. 16).
• From the log book compartment of the monitor cart, screw the support arm base to the
monitor cart using 4 Allen screws M6 x 16, 4 lock washers and 4 washers (included the
scope of delivery).

© Siemens, 2004 SPR2-230.812.02.03.02 Page 17 of 26 SIREMOBIL

10.08 CS PS SP
18 Installation of conversion set 7141125 (2 monitors)

Installing the TFT display on the support arm 3.2

Fig. 21: Collision protection Fig. 22: Adjustment of the support arm

NOTE You can adjust the width of the support arm and the distance
between the top and bottom tube to adapt the support arm to
the display in use. In addition, the vertical centering of the
support plate (2/Fig. 22 / p. 18) can be varied. The width of
the support arm is varied using spacer rings
(2/Fig. 21 / p. 18). The distance between the tubes and the
vertical centering of the support plate is variable after loos-
ening each of the 8 countersunk screws of the two vertical
display carriers. Only loosen the 16 countersunk screws
slightly - do not completely unscrew them!

• Temporarily remove the collision protection (Fig. 21 / p. 18). To do so, loosen the
screws (1/Fig. 21 / p. 18) on both top tubes and pull out the collision protection.

Adjusting the support arm to the size of the TFT display 0

• After loosening the 2 x 8 countersunk screws on the support arm(1/Fig. 22 / p. 18), you
can adjust the spacing between both tubes as well as the vertical position of the holding
plate (2/Fig. 22 / p. 18).
• Set the spacing (3/Fig. 22 / p. 18) to approximately 3.7 cm; retighten the countersunk
screws.

NOTE Setting the spacing to 3.7 cm results in a distance of approx.

1 cm between the top and bottom edge of the TFT displays,
on the one hand, and the tubes of the support arm, on the
other hand.

SIREMOBIL SPR2-230.812.02.03.02 Page 18 of 26 © Siemens, 2004

10.08 CS PS SP
Installation of conversion set 7141125 (2 monitors) 19

Installation 0

Fig. 23: Installation of the TFT displays

• The right and left collision guards (3/Fig. 23 / p. 19) are still removed.
• Place the first TFT display in front of the support.

NOTE The displays have 4 thread holes on the rear panel for attach-
ing the support.

• Screw in two of the countersunk screws M4 x 10, contained in the scope of delivery,
with washer and contact washer, but do not yet fully tighten (1/Fig. 23 / p. 19).
• Shift the TFT display out until it is possible to screw in the external screws. Do not yet
tighten the screws completely. It must be possible to shift the TFT display horizontally.
• Attach the second TFT display in the same way.
• Place both displays horizontally symmetrical to the center axle (2/Fig. 23 / p. 19).
- Make sure that there is a vertical clearance of approx. 2 mm between the displays.
• If both displays are properly positioned, tighten the fixing screws firmly.
• Refasten the left and right collision guard (3/Fig. 23 / p. 19).
To do so, insert a spacer ring, insert the collision guard into the tube and screw on.
• If required, correct the spacing between the displays and the top and bottom tube of the
support arm.
- Leave a couple of millimeters for ventilation between the displays and the top and
bottom tube of the support arm to prevent collisions due to vibrations while moving
the monitor cart is recommended.
- Both tubes of the support arm should run parallel to each other.

© Siemens, 2004 SPR2-230.812.02.03.02 Page 19 of 26 SIREMOBIL

10.08 CS PS SP
20 Installation of conversion set 7141125 (2 monitors)

Protective ground wiring of the support arm 3.3

Fig. 24: ON/OFF assembly _ 2

• A short protective ground wire is attached with stripped end to the support arm base.
Unscrew the terminal block and screw on the 2m long terminal block included in the
scope of delivery. Run the stripped end of the protective ground wire through the sup-
port arm base, through the logbook compartment and then through the lateral rail of the
monitor trolley to the ON/OFF assembly. Connect the cable end into an available
ground terminal (1/Fig. 24 / p. 20). Make sure that both protective ground wires make
good contact.

SIREMOBIL SPR2-230.812.02.03.02 Page 20 of 26 © Siemens, 2004

10.08 CS PS SP
Installation of conversion set 7141125 (2 monitors) 21

Wiring the radiation indicators of the support arm 3.4

Fig. 25: Displays' wiring

• Withdraw the two radiation indicators (4/Fig. 23 / p. 19), after loosening the lower
mounting screws laterally from the tube.
• One end of the cable of the additional radiation indicator (included in the scope of deliv-
ery) is equipped with 2 free cable ends. On the other end, a connector D50.X7 is
installed. Run both cable ends in the lower tube of the support arm through the two
bores (1/Fig. 25 / p. 21) to the radiation indicators.
• Connect both radiation indicators, then re-insert them in the bottom tube and retighten
them.
• Route the cable end with the attached connector D50.X7 through the support arm base
to the logbook compartment and then through the lateral rail of the monitor cart to the
ON/OFF assembly located below.
• Unplug connector X4 of the ON/OFF assembly. See (2/Fig. 24 / p. 20).
• Wire the Y-cable (included in the scope of delivery), together with the attached plug
connectors D50.X4, D50.X4A and D50.X7, as follows:

Y-cable connector D50.X4A ---- ON/OFF assembly board D50, connector D50.X4
Y-cable, coupling D50.X4 ---- Cable of radiation indicator, connector D50.X4
Y-cables, coupling D50.X7 ---- New support arm, radiation indicator, connector
D50.X7

• Attach the cables to the monitor cart using cable ties.

© Siemens, 2004 SPR2-230.812.02.03.02 Page 21 of 26 SIREMOBIL

10.08 CS PS SP
22 Installation of conversion set 7141125 (2 monitors)

Wiring of the displays 3.5

Fig. 26: Cover of the support arm

• Open the rear panel of both TFT displays above the connections.
• Route the power line cables and the video cables to the TFT displays.
• Connect the video cable to the BNC sockets VIDEO of the displays and lock it.

NOTE Only for SIREMOBIL Iso-C 3D:

Connect and lock the 3 line video cable to the BNC bushes
for the right display:
Green line - VIDEO
Blue line - CS/HS
Red line - VS

• Connect the shieldings of the video cables to the ground of the display.
• Plug in the power cables.
• Close both covers again located above the display connections.

Running the cables 0

• Pull back the power cords and video cables as needed into the monitor cart .
- Route the cables without sharp bending radius.
- Ensure that the cables are covered by both support arm rails in the area between
support arm base and the displays (Fig. 23 / p. 19) is recommended.
- The cables should rest in the cable bushes of the support arm base without exces-
sive pulling force or stress (Fig. 26 / p. 22).
• Reinstall the cover on the support arm (Fig. 26 / p. 22).

SIREMOBIL SPR2-230.812.02.03.02 Page 22 of 26 © Siemens, 2004

10.08 CS PS SP
Adjustments 23
4-
TFT display BARCO MVGD 1318, part number 80 79 530
4Adjustments

• Make the checks, and if necessary, adjustments according to the replacement instruc-
tions TD00-000.841.17...
Refer to the 'System-dependent settings' chapter of the instructions.

© Siemens, 2004 SPR2-230.812.02.03.02 Page 23 of 26 SIREMOBIL

10.08 CS PS SP
24 Adjustments

Final work steps 4.1

• Close all covers again. Make sure that the protective conductor connections make good
contact.
• Perform the protective conductor resistance test.
The protective conductor resistance must not exceed 0.2 Ω.
• Perform the IQ quick test of the system.
• Perform the country-specific acceptance tests (part acceptance).

SIREMOBIL SPR2-230.812.02.03.02 Page 24 of 26 © Siemens, 2004

10.08 CS PS SP
Changes to Previous Version 25
5Changes to Previous Version 5-
Document completely revised.

© Siemens, 2004 SPR2-230.812.02.03.02 Page 25 of 26 SIREMOBIL

10.08 CS PS SP
26 Changes to Previous Version

SIREMOBIL SPR2-230.812.02.03.02 Page 26 of 26 © Siemens, 2004

10.08 CS PS SP