UDR 1000 M K VI
UDR 1000 MKVI
UDR 1000 MKVI
DETAILED SPECIFICATIONS
TYPE All hydraulic top head drive. Rod Clamps & Slip Table
44.5mm (1-3/4”) to 177.8mm (7”) rod clamp jaws,
Drill Mast 9m (30ft) rod pull capacity. 12.0m (39’4”) long. Designed hydraulically operated and self energising. Casing and rod
for drilling angles between vertical and 45°. slips, hammer, spanners, bit breaker baskets, 320mm (12-
Incorporating a dual point mast pivot frame and 1300mm 5/8”) mast bottom opening, 224mm (8-3/4”) rod clamp
(4’3”)hydraulic mast dump to ground level at 45° drilling opening.
angle.
Wireline Winch 1500m (4920ft) of 6mm (1/4”) wire rope. 12.6 kN (2800) lbf
Diesel Motor Cummins 6CTA8.3 producing 172kW (230hp) at 2200 rpm full drum pull at 430m (1410ft) per minute. 21.4 kN (4800 lbf)
to power hydraulics. bare drum pull at 255m (835ft) per minute.
Rotation Head UDR D15 Top head drive coupled. High low manual gear Hydraulics Highest quality axial and radial piston pumps and motors
change. 7.5:1 first stage planetary, 3:1 helical gear final used in three independent open circuits (Main – Water –
drive. 3-1500 rpm. Stepless speed control, 3-2000 rpm Cylinders). Full flow 10 micron Beta rated return oil filtration.
in low gear and 200 - 1500 rpm in high gear. Larger than average hose and control valve sizes used to
Output Torque 100% Efficiency: achieve highest possible circuit efficiency. Proven reliability
Intermittent: 14324 Nm (10557ft-lbf) 373 rpm over thousands of hours can be demonstrated.
Continuous: 966 Nm (712 ft-lbf) 1000 rpm
644 Nm (475 ft-lbf) 1500 rpm Rod Carry Rack Tray type for 6m (20ft) lengths of drill pipe situated on the
Fully automatic torque-speed control for diamond right hand side of the drill tray. Nominal capacity 20 x 6m
drilling, running the bit always at maximum possible (20ft) lengths of 114mm (4-1/2”) pipe.
rpm, using maximum available horsepower. 68mm
(2.68”) ID hollow spindle, floating 50mm (2”) jet Rod Boom & Winch
lubricated gears and bearings. Air to lube oil heat Hydraulic, fully variable rod handling boom from all angles
exchanger fitted. from vertical to 45°. Main boom swivelling to side and fitted
with 3.1kN winch.
Head Traverse Hydraulic cylinder over ropes, 2:1 ratio. 7.32m (24ft)
traverse, with maximum traverse speeds of 44.8m Depth Capacity
Drilling Technique Hole OD Rod OD Depth
(147ft) per minute up and 29.6m (97ft) per minute down.
Hydraulic head rack back. 1. High pressure down 165mm 89mm 520m
the hole hammer drilling 6-1/2” 3-1/2”
Pull Down 70 Kn (15,700 lbf) and rotary non core, mud
or air flush
Pull Out 112 kN (25,200 lbf) N+ H+
2. Diamond core:
M 1500 1000
Rod Pull 9m (30 ft)
FT (5,000) (3,300)
Main Hoist 122.7 Kn (27590 lbf) maximum pull, 120m (394 ft) per
minute maximum speed. Mast top mounted, single line NOTE: Diamond drill depth capacities based on straight, vertical, clean fluid filled
pull. Fully automatic pull-speed control pulling the rod holes. No allowance made to break core. + refers to “O”, “Q”, “T” or similar
string always at maximum possible speed using wireline systems.
maximum available horsepower.
Approximate Weight and Dimensions
Water Pump Bean W1122BCD, 140 L/min at 7000 kPA (37 gpm US at Bare drill on hydraulic jack-up tray
1000 psi). Options available. Weight: 15000kg (33000lb)
Length: 12.0m (39’4”)
Rod Break Out Options available. Width: 2.5m (8’2”)
With hydraulic chain tong up to 24,200 Nm (18000ft-lbf) Height: 3.6m (11’10”)
torque for 83mm (3-1/4”) to 210mm (8-1/4”) OD pipe.
Specifications are as at 5 June 2003, and are subject to changes or modifications,
which are made from time to time by UDR and its suppliers in accordance with their
policies to update and improve their products.
100 Grindle Road PO BOX 204 Telephone + 61 7 3715 4700
Rocklea 4106 Salisbury 4107 Fax + 61 7 3715 4747
Queensland Queensland Email sales@udrgroup.com
Australia Australia Internet www.udr.com.au
