GE Fanuc

Embedded Systems

CR11
Rugged 6U CompactPCI® SBC with Dual Core 32- or 64-bit Processor
Features The CR11 is a 6U CompactPCI CPU board with inte- The CR11 provides a unique feature set, including
• Intel® CoreTM2 Duo processor 1.5 GHz and grated dual core Intel Core 2 Duo or Intel Core Duo up to 4 GB of DDR2 SDRAM (200 MHz) with
2.16 GHz Processor and dual Gigabit Ethernet PICMG 2.16 enhanced ECC, four independent on-board PCI
• Intel® CoreTM Duo processor 1.66 GHz and channels. The Intel dual core processor includes buses, system host and peripheral mode support
2.0 GHz two optimized execution cores in a single for the CPCI backplane, two PMC interfaces
processor case. This enables execution of parallel (64-bit/133 MHz and 32-bit/33 MHz). Instead of
• Intel Celeron® M processor ULV 423, 1.06 GHz
threads or applications on separate cores with the PMC1, a PCI Express™ based XMC interface is
• PICMG 2.1 (Hot Swap ) compliant
dedicated CPU resources. The CR11 supports a available on request. A high level of functional inte-
• Ultra compact, one slot 32- and 64-bit processor architecture. The CR11 gration (two Gigabit Ethernet, one Fast Ethernet,
• System and non-system functionality is designed to meet the requirements of markets two serial interfaces (RS-232 or RS-422/485),
• Up to 4 GB DDR2 SDRAM (200 MHz) with ECC such as automation, simulation/training, test and USB 2.0, integrated HDD or Flash drive) within a
• Flash drive or local UDMA100 2.5” hard disk measurement, and military. single slot gives users the freedom to use the PMC
• 2 x SATA, RAID 0/1 capable interfaces for their application specific I/O. The
Based on the Intel Core Duo Processor, the plat- VGA/DVI interface is supported through a high
• Front/rear VGA up to 1280 x 1024, rear DVI-I up
form is designed to support processor speeds performance 2D/3D ATI® video controller capable
to 1280 x 1024, 32 MB RAM
from 1.06 GHz up to 2.0 GHz. The Intel Core 2 Duo of driving two displays in parallel.
• Two Gigabit Ethernet ports 10/100/1000 BaseT runs at 1.5 GHz and 2.16 GHz. Rugged needs are
front or rear optional addressed with optional conduction cooling and Versions with front panel I/O are available in
• PICMG 2.16 compliant extended temperature range of -40 °C to +80 °C various configurations with one or two
• One front Fast Ethernet port (depends on selected board options). Increased PMC interfaces. The PMC1 interface can be
• Two PMC extension slots, one 64-bit/133 MHz shock and vibration immunity is designed in by ordered as an XMC interface instead.
and one 32-bit/33 MHz using optional stiffener bars and wedge locks.
• One XMC interface on request Conformal coating is optional. Supported operating systems are Windows®,
• 2 x serial I/O with FIFOs Linux® and VxWorks®. Integrity is available
RS-232/422/485 interface on request.
• 4 x USB 2.0 ports, two front and two on rear
• Audio codec
• Watchdog, temperature sensors
• Optional –40 °C to +80 °C
• Optional conduction cooling
• Optional conformal coating
• High shock and vibration immunity with
stiffener bars and wedge locks
• Customer specific, low cost assembly versions
• RoHS compliant
CR11 Rugged 6U CompactPCI® SBC with Dual Core 32- or 64-bit Processor

Specifications VGA and DVI – ATI X300™

• 256-bit 3D and 2D graphics accelerator
Processor - µFCBGA, Low Power Design • On-chip 32 MB memory
• Scalable processing power with flexible • PCI Express x4 interface
processor design • Dual CRT/Simultaneous Dual Display (same or
• Supports 32-bit and 64-bit processor architecture different surfaces)
• 64-bit: Intel Core 2 Duo processor: 1.50 GHz and • Integrated 300 MHz Palette DAC for analog VGA
2.16 GHz monitors up to 1280 x 1024
• 32-bit: Intel Core Duo processor: 1.66 GHz and 2 GHz • Single channel DVI-I interface PanelLink® for TFT
• 32-bit: Intel Celeron M processor ULV 423: 1.06 GHz displays up to 1280 x 1024 true color (EDID displays
• High efficiency on-board switching regulator (DC/DC) PnP supported)
• Fanless cooling with heat sink • Fully compliant support for OpenGL for all Windows
* Contact factory for latest CPU versions operating systems and Linux
Processor FSB MHz Level 2 Cache • Versions with front (not in conduction-cooled style) or
Core 2 Duo 667 4 MB rear I/O available
Core Duo 667 2 MB
EIDE – 6300ESB
Celeron M 533 1 MB
• Ultra ATA/100 sync. DMA mode up to 100 MB/s
CompactPCI – PLX 6466 PCI-to-PCI Bridge • PIO mode 4 and bus master IDE up to 16 MB/s
• PICMG 2.0 R3.0 compliant CPCI local bus standard • One device via on board connector and two devices
• 64-bit PCI-to-PCI bridge for up to 8 slots (33 MHz) or via rear I/O available
5 slots (66 MHz) General Purpose I/O
• Supports System Host and Peripheral Mode • 8 GPIO (input or output) pins
• J1+2, 2 mm pin and socket connectors • Software configurable
(IEC-1076-4-101)
USB 2.0 – 6300ESB
Chipset – Intel E7520/6300ESB • Two USB 2.0 channels on rear I/O
• Four parallel PCI Express connections to major • Two USB 2.0 channels on front (not in conduction-
components for maximum I/O throughput cooled style)
Memory – DDR2-400 Keyboard, Mouse
• High-speed registered DDR2 SDRAM with 400 MHz • Via USB
• 144-bit wide with enhanced error correction (ECC) • Legacy PS/2 controller emulation
• 32-bit CPU: up to 4 GB soldered memory (usable size
Real-time clock
depends on operating system)
• RTC 146818 compatible
• 64-bit CPU: up to 4 GB soldered memory
• Li-battery (not in conduction-cooled style)
Dual Gigabit Ethernet – Intel 82571EB
CMOS RAM
• Dual Channel Ethernet Controller with
• 242 bytes non-volatile CMOS RAM for BIOS use
PCI Express x4 interface
• 10/100/1000BaseT auto-negotiation EEPROM
• Versions with front I/O available (not conduction- • 512 Kbit serial EEPROMs for non-volatile user data
cooled style) Floppy
• Compliant to PICMG 2.16 • Via USB
Fast Ethernet – Intel 82551QM Watchdog
• Single channel Ethernet Controller • Intel TCO timer
• 10/100BaseT auto-negotiation • Intel 6300ESB watchdog
• Front I/O (not conduction-cooled style)
Timer
Hard Disk or Flash Drive • Integrated in 6300ESB chipset
• Internal 2.5” UDMA100 IDE hard disk or • Legacy PC-AT timer
Flash Drive for extended temperature range and • High Precision Event Timer (HPET)
higher shock/vibration immunity)
Temperature Sensors
PMC Extension Slots - IEEE P1386/1386.1 • CPU die and pcb temperature software readable in
• PMC1 (64-bit/133 MHz) and PMC2 (32-bit/33 MHz), the range of –55 °C to +125 °C
XMC (PCIe x4) on PMC1 available on request.
• Enhancement to processor PMC standard LED (not in conduction-cooled style)
VITA 32-2003 (non-monarch) • Front panel ACPI System Status Indicator LED (red/
• PMC1 signaling is 3.3 V only, PMC2 signaling is amber/green)
5 V tolerant. • CompactPCI hot swap (blue) on front panel
NoTE: PMC front I/O is not supported with CR11 in Audio
style 8. • Line In, CD In
Serial I/O - RS232/422/485 • Headphone, SPDIF Out
• Two async. 16550 compatible full duplex serial • AC97 link with codec
channels at rear I/O
• High-speed transfer up to 115.2 Kbaud with Hot Swap - compliant to PICMG 2.1
16 byte FIFOs • Peripheral mode: Full CompactPCI hot swap
• User selectable RS232/422/485 interface • System Host mode: CompactPCI ENUM# event
• COM1 optionally available at front (RJ45), not in style 8 supported through ACPI or legacy driver
 CR11 Rugged 6U CompactPCI® SBC with Dual Core 32- or 64-bit Processor

BIOS Features Power Consumption - typical operating current

• AMI BIOS Core 8, in-system programmable Flash ROM • Without keyboard, hard disk, modules, Ethernet (no
• Automatic system configuration link), measured at DOS prompt, no power savings.
• Integrated VGA, SATA RAID and Ethernet PXE ROM 512 MB memory option.
• USB Mass Storage support Processor 5V 3.3 V Total Power
• Password protection
Core 2 Duo, 2.16 GHz 4.9 8.4 52.2
• Headless support
Core 2 Duo, 1.5 GHz 3.1 8.4 43.2
• Remote console through serial port
Core Duo, 2.00 GHz 4.0 8.4 47.7
Software Core Duo, 1.66 GH 2.7 8.4 41.2
• The following software is supported to the extent Celeron M, 1.06 GHz 1.2 8.4 33.7
listed below.
OS On Request Planned Available • Without keyboard, hard disk, modules, Windows XP,
Windows √ 3D graphics active. Both Gigabit Ethernet channels
Linux √ linked, CPU running at instruction mix for maximum
VxWorks √ power consumption.
Integrity √ 2 GB memory option.
Processor 5V 3.3 V Total Power
Front and Rear I/O (with transition module CTM17)
Core 2 Duo, 2.16 GHz 7.1 10.1 68.8
• The pin outs of the transition module connectors
Core 2 Duo, 1.5 GHz 4.1 10.1 53.8
(rear I/O) correspond to standard PC connectors
Core Duo, 2.00 GHz 5.8 10.1 62.3
(press-fit cables).
Core Duo, 1.66 GHz 3.7 10.1 51.8
Function Front Rear Celeron M, 1.06 GHz 1.4 10.1 40.3
Style 1 / 3 J3 / J4 /J5
DVI-I - √ 1, Power Allowances – PMC/XMC slots
VGA √3 √ 1, • +5 V, +3.3 V: Total power max. 7.5 W
Gigabit Ethernet 1 √ 2, 3 √2 • ±12 V: 100mA each
Gigabit Ethernet 2 √ 2, 3 √2
Mechanical – PICMG 2.0
Fast Ethernet √ -
• 6U, 1 slot wide, (233 x 160 x 20) mm with Flash Drive
Reset √ √
or hard disk
LEDs √ √
• Compliant to VITA30.1-2002 for conduction-
USB 2.0 1-4 1-2 3-4
cooled board
IDE primary onboard
IDE secondary √ Temperature
SATA 1 √ • Note: For detailed information about the operating
SATA 2 √ temperature behavior of the board of any style it is
COM 1-2 1 1, 2 absolutely necessary to consult the manual. The pro-
Audio √ cessor type and speed, altitude, the use or not use of
GPIO (8 pins) - √ Ethernet and video, ambient conditions and the type
PMC 1 (XMC on req.) √ √ of cooling influence the board temperature range.
PMC 2 I/O √ √ Temperature (except conduction-cooled style)
*1 Rear DVI-I connector for DVI and VGA • All values under typical conditions without
*2 Either front or rear as an order option PMC module
*3 The 32-bit/33 MHz PMC2 slot is not available with VGA or Range Operating Storage
Ethernet on the front or with IDE installed.
Standard 0 °C to +55 °C –40 °C to +85 °C
Styles Extended –40 °C to +75 °C –40 °C to +85 °C
Function Style 1 Style 3 Style 6 Style 8 Note: Without battery, the storage temperature is -55 °C to +105 C

Front Panel yes yes yes no Temperature (conduction-cooled style)

Front Stiffener no no no yes • All values under typical conditions without
Middle Stiffener no no yes yes ccPMC module
Wedge Locks no no no yes Range Operating Storage
Parts Soldered yes yes yes yes Extended –40 °C to +80 °C –55 °C to +105 °C
Li-Battery yes yes no no
Ext. Temperature no yes yes yes
Operating Storage
Conformal
Coating no no yes yes Humidity 5 – 95 % @ 40 °C 5 – 95 % @ 40 °C
Conduction Altitude 15,000 ft. (4.5 km) 40,000 ft. (12 km)
Cooled no no no yes • Vacuum for conduction cooled board
Power Requirements
Shock and Vibration
• +5 V, +3.3 V, +12 V Required
• Designed to meet VITA47 class EAC1, EAC3, EAC6
• -12 V If required by mounted PMC module
and ECC4
VITA 47
• Designed to meet VITA47 class EAC1, EAC3, EAC6
and ECC4
MTBF
• Calculations are available in accordance with
MIL-HDBK-217. Please contact Ge Fanuc Embedded
Systems.
Safety
• Designed to meet standard UL1950, CE class A, FCC-A
CR11 Rugged 6U CompactPCI® SBC with Dual Core 32- or 64-bit Processor

Block Diagram

Intel
Core 2 Duo
Core Duo
Processor

DDR2 SDRAM PCI-E

with ECC PMC1/XMC
(4 GB) PCI-X (64-bit/133 MHz)

cPCI Backplane (64-bit/66 MHz)

PCI-E Intel
E7520 PCI-E Intel
VGA/DVI
6700
PCI-E PXH PCI/PCI PCI
Dual Gigabit
Ethernet Bridge

SATA PCI PMC2

(32-bit/33 MHz)

COM
Intel
USB
6300ESB
LPC PCI
GPIO Fast Ethernet
AC97
EIDE Audio

Hot Swap

Ordering Information
Hardware Accessories
CTM17: I/O transition module for 6U backplane (IEEE 1101.11-1998 compliant)
SCC784UE05CR11R: 7U, 19” starter cage with 5 CPCI slots, backplane, HDD, DVD, power supply

Operating Systems
Extensive operating systems support is available, (see page 2 of this document).
Chassis with power supplies, backplanes and drives on request.
For detailed information and further options, contact GE Fanuc Embedded Systems.

About GE Fanuc Embedded Systems

GE Fanuc Embedded Systems is a leading global provider of embedded computing solutions for a wide
range of industries and applications. Our comprehensive product offering includes many types of I/O,
single board computers, high performance signal processors, fully integrated, rugged systems including
flat panel displays, plus high speed networking and communications products. The company is head-
quartered in the U.S. and has design, manufacturing and support offices throughout the world. Whether
you’re looking for one of our standard products or a fully custom solution, GE Fanuc Embedded Systems
has the breadth, experience and 24/7 support to deliver what you need. For more information, visit
www.gefanucembedded.com.

GE Fanuc Embedded Systems Additional Resources

Information Centers
For more information, please visit the GE Fanuc
Americas: Embedded Systems web site at:
1 800 322 3616 or 1 256 880 0444

Asia Pacific: www.gefanucembedded.com

86 10 6561 1561

Europe, Middle East and Africa:

+49 821 5034-0

©2007 GE Fanuc Embedded Systems. All rights reserved.

All other brands or names are property of their respective holders.
Specifications are subject to change without notice. 06.07 GFA-852