Wood-Mizer® Sawmill

Parts Manual

LT40 rev. K5.03

Safety is our #1 concern!

Form #606

WARNING! Read and understand this

! manual before using this machine.
 California
Proposition 65 Warning

WARNING: Breathing gas/diesel engine exhaust exposes you to chemicals known to

the State of California to cause cancer and birth defects or other reproductive harm.

Always start and operate the engine in a well-ventilated area.

If in an enclosed area, vent the exhaust to the outside.
Do not modify or tamper with the exhaust system.
Do not idle the engine except as necessary.

For more information go to www.P65warnings.ca.gov.

WARNING: Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the State of California to cause cancer. Avoid inhaling
wood dust or use a dust mask or other safeguards for personal protection.

For more information go to www.P65Warnings.ca.gov/wood.

Active Patents assigned to Wood-Mizer, LLC

Wood-Mizer, LLC has received patents that protect our inventions which are a result of a dedication to
research, innovation, development, and design. Learn more at: woodmizer.com/patents

©2022 Wood-Mizer LLC

Printed in the United States of America, all rights reserved. No part of this manual may be reproduced in any form by any
photographic, electronic, mechanical or other means or used in any information storage and retrieval system without
written permission from

Wood-Mizer, LLC
8180 West 10th Street
Indianapolis, Indiana 46214
Table of Contents Section-Page
SECTION 1 REPLACEMENT PARTS
1.1 How To Use The Parts List.................................................................... 1-1
To Order Parts ......................................................................1-1
1.2 Sample Assembly................................................................................... 1-1
1.3 Torque Values ...................................................................................... 1-2

SECTION 2 BLADE GUIDE ROLLERS & ARM

2.1 Blade Guide Assembly, Idle Side .......................................................... 2-1
2.2 Blade Guide Assembly, Drive Side ....................................................... 2-4
2.3 Blade Guide Arm Drive Assembly ........................................................ 2-7
2.4 Blade Guide Arm ................................................................................... 2-9

SECTION 3 BLADE WHEELS & TENSIONER

3.1 Blade Drive Assembly ........................................................................... 3-1
LT30 D35/D36
LT40 D35/D36.......................................................................3-1
3.2 Blade Drive Assembly ........................................................................... 3-3
LT30 G28 -- LT30HD G28
LT40 G28 -- LT40HD G28 Remote.......................................3-3
3.3 Idle Blade Wheel Assembly................................................................... 3-5
3.4 Hydraulic Blade Tensioner Assembly ................................................... 3-6

SECTION 4 SAW HEAD FRAME

4.1 Middle Throat Screw ............................................................................. 4-1
4.2 Water Lube Solenoid Valve................................................................... 4-2
4.3 Clutch/Brake Lever Assembly (D35/D36) ............................................ 4-3
4.4 Clutch Mount Assembly ........................................................................ 4-5
4.5 Brake Assembly ..................................................................................... 4-6
4.6 Water Lube Assembly (Gas Only)......................................................... 4-7
4.7 Water Lube Assembly (Diesel & Electric Only) ................................... 4-8
4.8 Saw Head Decals ................................................................................. 4-10
4.9 Blade Housing Covers ......................................................................... 4-11
4.10 Drive Belt Covers................................................................................. 4-13
4.11 Sawdust Chute...................................................................................... 4-14
4.12 Debarker Wire Box/Hole Plugs ........................................................... 4-15
4.13 Board Return Assembly (Optional) ..................................................... 4-16

SECTION 5 CONTROL & BATTERY BOXES

5.1 Control Assembly .................................................................................. 5-1
5.2 Control Assembly (Tier4 Only) ............................................................. 5-3
5.3 Drum Switches....................................................................................... 5-5
5.4 Circuit Breakers ..................................................................................... 5-6
5.5 Front Panel Assembly & Harnesses....................................................... 5-7
5.6 Front Panel Assembly & Harnesses (Tier4 Only) ................................. 5-9
5.7 Battery Box Assembly ......................................................................... 5-10

SECTION 6 UP/DOWN SYSTEM

6.1 Saw Head Mount.................................................................................... 6-1

Table of Contents WM doc 11/23/22 iii

Table of Contents Section-Page
6.2 Blade Height & Quarter Scales ..............................................................6-2
6.3 Up/Down Chain & Sprockets .................................................................6-4
6.4 Up/Down Assembly ...............................................................................6-5

SECTION 7 FEED SYSTEM & TRACK ROLLERS

7.1 Upper Track Rollers And Wipers...........................................................7-1
7.2 Power Feed Assembly ............................................................................7-2
7.3 Feed Chain/Stop .....................................................................................7-4
7.4 Lower Track Rollers...............................................................................7-5

SECTION 8 BED FRAME ASSEMBLY

8.1 Bed Rail Assembly .................................................................................8-1
8.2 Bed Rail Assembly, Front And Rear......................................................8-1
8.3 Bed Rail Assembly, Middle Front..........................................................8-3
8.4 Bed Rail Assembly, Middle Rear...........................................................8-4
8.5 Leg Assembly (Stationary).....................................................................8-5
8.6 Pivot Bed Rail Assembly........................................................................8-7
8.7 Log Side Support Assembly (Manual) ...................................................8-8
8.8 Safety Chain Assembly ........................................................................8-10
8.9 Saw Head Rest Pin Assembly ..............................................................8-11
8.10 Rest Pin Assembly................................................................................8-12
8.11 Bed Frame Decals.................................................................................8-13
8.12 Log Clamp ............................................................................................8-14
8.13 Log Loading Ramps ............................................................................8-15
8.14 Board Return Table Assembly (Optional)............................................8-16
8.15 Board Outfeed Table (Optional)...........................................................8-17
8.16 Manual Winch ......................................................................................8-18

SECTION 9 BED HYDRAULIC LOG LOADER & TURNER (OPTIONAL)

9.1 Hydraulic Hoses .....................................................................................9-1
9.2 Hydraulic Loader/Turner Control Box ...................................................9-2
9.3 Hydraulic Power Supply Strip................................................................9-4
9.4 Hydraulic Log Loader (Optional)...........................................................9-6
9.5 Hydraulic Log Turner (Optional) ...........................................................9-8
9.6 Hydraulic Log Side Supports (Optional)..............................................9-10
9.7 Miscelleneous Loader & Turner Parts..................................................9-12

SECTION 10 MISCELLANEOUS
10.1 Replacement Manuals .........................................................................10-1

INDEX I

iv WM doc 11/23/22 Table of Contents

 Replacement Parts
How To Use The Parts List 1
SECTION 1 REPLACEMENT PARTS
1.1 How To Use The Parts List

 Use the table of contents to locate the assembly that contains the part you need.

 Go to the appropriate section and locate the part in the illustration.

 Use the number pointing to the part to locate the correct part number and description in the table.

 Parts shown indented under another part are included with that part.

To Order Parts

 From the continental US, call 1-800-525-8100 to order parts. Have your customer number, vehicle
identification number, and part numbers ready when you call.

 From other international locations, contact the Wood-Mizer distributor in your area for parts.

1.2 Sample Assembly

REF PART # DESCRIPTION COMMENTS QTY.

012345 SAMPLE ASSEMBLY, COMPLETE INCLUDES ITEMS 1-6 1
1 F02222-22 Sample Part 1
2 F03333-33 Sample Part 2
098765 Sample Subassembly Includes items 3-6 1
3 S04444-44 Subassembly Sample Part 1
4 K55555 Subassembly Sample Part 1
054321 Sample Sub-Subassembly Includes items 5-6 2
5 022222 Sub-Subassembly Sample Part 1
6 F10234-56 Sub-Subassembly Sample Part 1

The Sample Assembly, Complete, part number 02345 (top level assembly) includes two parts (F0222-22
and F0333-33) and the 098765 subassembly.

Subassembly 098765 contains two parts(S04444-44 and K55555) and two copies of sub-subassembly
054321.

Each sub-subassembly 054321 contains two parts (022222 and F10234-56).

Replacement Parts WM doc 11/23/22 1-1

 Replacement Parts
1 Torque Values

1.3 Torque Values

Grade Units SAE 5 SAE 8

Grade Mark

Bolt Threads.
Units SAE 5 SAE 8
Dia. Per In.
6 32 in-lbs (Nm) 20 (2.3) -
8 32 in-lbs (Nm) 24 (2.7) 30 (3.4)
10 24 in-lbs (Nm) 35 (4.0) 45 (5.1)
10 32 in-lbs (Nm) 40 (4.5) 50 (5.7)
12 24 in-lbs (Nm) 50 (5.7) 65 (7.3)
1/4 20 in-lbs (Nm) 95 (10.7) 125 (14.1)
1/4 28 in-lbs (Nm) 95 (10.7) 150 (17.0)
5/16 18 ft-lbs (Nm) 17 (22.6) 23 (31.2)
5/16 24 ft-lbs (Nm) 20 (27.1) 25 (33.8)
3/8 16 ft-lbs (Nm) 30 (40.7) 40 (54.2)
3/8 24 ft-lbs (Nm) 35 (47.5) 45 (61.0)
7/16 14 ft-lbs (Nm) 50 (67.8) 65 (88.1)
7/16 20 ft-lbs (Nm) 55 (74.6) 70 (94.9)
1/2 13 ft-lbs (Nm) 75 (101.7) 100 (135.6)
1/2 20 ft-lbs (Nm) 85 (115.3) 110 (149.2)
9/16 12 ft-lbs (Nm) 105 (142.4) 135 (183.1)
9/16 18 ft-lbs (Nm) 115 (155.9) 150 (203.4)
5/8 11 ft-lbs (Nm) 150 (203.4) 195 (264.4)
5/8 18 ft-lbs (Nm) 160 (217.0) 210 (284.8)
3/4 10 ft-lbs (Nm) 170 (230.5) 220 (298.3)
3/4 16 ft-lbs (Nm) 175 (237.3) 225 (305.1)
7/8 9 ft-lbs (Nm) 302 (409.5) 473 (640.9)
7/8 14 ft-lbs (Nm) 300 (406.8) 400 (542.4)
1 8 ft-lbs (Nm) 466 (631.8) 714 (967.4)

0HWULF%ROW+HDG  

,GHQWLILFDWLRQ 0HWULF 0HWULF
*UDGH *UDGH

COARSE THREAD FINE THREAD

Wrench
Diameter & Metric 8.8 Metric 10.9 Diameter & Metric 8.8 Metric 10.9
Thread Thread Size
Pitch N-m lbs-ft N-m lbs-ft Pitch N-m lbs-ft N-m lbs-ft
6 x 1.0 8 6 11 8 10 mm
8 x 1.25 20 15 27 20 8 x 1.0 21 16 29 22 13 mm
10 x 1.5 39 29 54 40 10 x 1.25 41 30 57 42 16 mm
12 x 1.75 68 50 94 70 12 x 1.25 75 55 103 76 18 mm
14 x 2.0 109 80 151 111 14 x 1.5 118 87 163 120 21 mm
16 x 2.0 169 125 234 173 16 x 1.5 181 133 250 184 24 mm
18 x 2.5 234 172 323 239 18 x 1.5 263 194 363 268 27 mm
20 x 2.5 330 244 457 337 20 x 1.5 367 270 507 374 30 mm
22 x 2.5 451 332 623 460 22 x 1.5 495 365 684 505 34 mm
24 x 3.0 571 421 790 583 24 x 2.0 623 459 861 635 36 mm
30 x 3.0 1175 867 1626 1199 30 x 2.0 1258 928 1740 1283 46 mm

1-2 WM doc 11/23/22 Replacement Parts

 Blade Guide Rollers & Arm
Blade Guide Assembly, Idle Side 2
SECTION 2 BLADE GUIDE ROLLERS & ARM
2.1 Blade Guide Assembly, Idle Side

3 22

21 4
2
20
19
2 2 37
30 41 25
3 23
29 36
24 10 28
1 40 35 43
2 31 32
44
3 5 27
8 45
26
6
38
17 9 33
6 39 34
11
47 7 12 42
13 14 46
49
52 15
48
16
51 17
50

18
53
Optional Relube 54
3H0994-1E
Blade Guide Roller

REF PART # DESCRIPTION COMMENTS QTY.

003992 GUIDE ASSEMBLY, IDLE SIDE BLADE ROLLER 1
003920 Block Assembly, Idle Side Blade Guide Mount 1
1 003921 Block Weldment, Blade Guide Mount Available in assemblies only. 1
2 F05010-17 Nut, 5/16-18 Hex 4
3 F05006-88 Bolt, 5/16-18 x 1” Hex Head Stainless 3
Steel
4 F05006-122 Screw, 5/16-18 x 1” Socket Head Flat 1
Point Stainless Steel Set
5 003924 Shaft Weldment, Idle Side Guide 1
6 P30127 Fitting, 1/8” NPT Socket Pipe Plug 3
7 007734 Fitting, 1/16” NPT Socket Pipe Plug 2
8 006322 Bracket Weldment, Idle Side Water Lube 1
9 F05007-78 Bolt, 3/8-16x1 1/2 Hex Head Grade 5 1
10 F05010-10 Nut, 3/8-16 Hex Nylon Lock 1
A04925 Roller Assembly, Blade Guide (standard) 1

Blade Guide Rollers & Arm WM doc 11/23/22 2-1

 Blade Guide Rollers & Arm
2 Blade Guide Assembly, Idle Side

REF PART # DESCRIPTION COMMENTS QTY.

014299 Roller Assembly, Extended Blade Guide High-Performance Blade Guide 1
(optional for use with 1 1/2” blades) Kit requires LMS blade lube sys-
tem. Use kit 006325 to upgrade
both drive and idle side blade
guides to High-Performance. If
sawmill not already equipped
with LMS, add kit .
K07079 Bearing Kit, Blade Guide Rebuild 1
11 P04252 Washer, 5/8" White Felt 1
12 F04254-1 Ring, 1 1/8" Interior Retaining 1
13 015975 Bearing, R8-2RS Blade Guide Available in assemblies only. 2
14 P06455 Washer, 5/8" Gray Felt 1
F05005-105 Screw, 1/4-28 x 1/4” Socket Head 1
Cup Point Set Black Oxide
057407-1507 Instruction Sheet, Blade Guide 1
Rebuild
15 S04250 Roller, Flanged Blade Guide Available in assemblies only. 1
014298 Roller, Flanged Blade Guide (1 1/2” Available in assemblies only. 1
blade)
A04925-364 Instruction Sheet, Blade Guide Roller 1
Replacement
16 S04253 Spacer, Blade Guide 2
17 F05011-125 Washer, 1/2” Nord-Lock 1
18 F05008-10 Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 1
19 F05011-17 Washer, 5/16” SAE Flat 2
20 F05011-13 Washer, 5/16” Split Lock 2
21 F05006-76 Bolt, 5/16-18 x 1 1/2” Hex Head 2
22 035656 Bolt, Blade Guide Vertical Adjustment 1
23 F05010-17 Nut, 5/16-18 Hex 1
24 F05006-136 Bolt, 5/16-18 x 2 3/4” Hex Head Full Thread 1
006325 GUIDE KIT, HIGH-PERFORMANCE BLADE High-Performance Blade Guide 1
GUIDE (OPTIONAL) Kit requires LMS blade lube sys-
tem. Use kit 006325 to upgrade
both drive and idle side blade
guides to High-Performance. If
sawmill not already equipped
with LMS, add kit .
003928 Block Assembly, Idle Side Blade Guide 1
25 003915 Plate, Block Tilt Adjustment 1
26 003909 Block, Guide Block Mount 1
27 F05012-22 Pin, 3/16” x 5/8” Roll 2
28 F05011-3 Washer, 3/8” SAE Flat 1
29 F05011-4 Washer, 3/8” Split Lock 1
30 F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 1
31 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head 1
32 003914 Ball, 3/16” Dia. Nylon 2
33 F05011-14 Washer, 1/4” Split Lock 2
34 F05005-15 Bolt, 1/4-20 x 1/2” Hex Head 2
35 003994 Bolt, Blade Guide Block Mount 1
36 042867 Washer, #10 Brass 1
37 F05004-240 Bolt, #10-32 x 1 1/4” Hex Head Stainless 1
Steel
38 044057 Screw, Lower Block Adjustment 1

2-2 WM doc 11/23/22 Blade Guide Rollers & Arm

 Blade Guide Rollers & Arm
Blade Guide Assembly, Idle Side 2
REF PART # DESCRIPTION COMMENTS QTY.
39 F05004-200 Screw, #10-32 x 3/8” Socket Head Stain- 1
less Steel
40 F05011-17 Washer, 5/16” SAE Flat 1
41 F05011-13 Washer, 5/16” Split Lock 1
42 052355 Block, Blade Guide Wear (Standard for 1 1/4” 052355 blocks for use with 1 2
Blades) 1/4" blade provided as standard
equipment. EZ-Glide blocks
036347 are available for cus-
tomers who prefer this block.
052309 Block, Blade Guide Wear (Optional for 1 1/2” Bearing must be modified for 2
Blades) use with relube roller assem-
blies. Remove one seal from
036347 Block Assembly, 1” Sq. EZ-Glide Wear 2
each bearing, place open sides
facing each other and place
spacer 035411 between bear-
ings.
43 035799 Block, Blade Guide Alignment 1
44 F05011-20 Washer, #10 Split Lock 1
45 F05004-152 Screw, #10-32 x 5/8” Hex Head 1
46 044064 Adjustment Tool, Lower Guide Block 1
035248 Shim, .008" Blade Guide Block Spacer 1

Drive Side Blade Guide Parts ((See Section

2.1))
016568 ROLLER ASSEMBLY, BLADE GUIDE RELUBE 1
(OPTIONAL)
057405 ROLLER ASSEMBLY, EXTENDED BLADE High-Performance Blade Guide 1
GUIDE RELUBE (OPTIONAL FOR USE WITH 1 Kit requires LMS blade lube sys-
1/2” BLADES) tem. Use kit 006325 to upgrade
both drive and idle side blade
guides to High-Performance. If
sawmill not already equipped
with LMS, add kit .
057407 Bearing Kit, Relube Blade Guide Rebuild 1
47 P04252 Washer, 5/8" White Felt 1
48 F04254-1 Ring, 1 1/8" Interior Retaining 1
49 015975 Bearing, R8-2RS Blade Guide Available in assemblies only. 2
Bearing must be modified for
use with relube roller assem-
blies. Remove one seal from
each bearing, place open sides
facing each other and place
spacer 035411 between bear-
ings.
50 P06455 Washer, 5/8" Gray Felt 1
51 035411 Spacer, Blade Guide Bearing 1
057407-1507 Instruction Sheet, Blade Guide Rebuild 1
52 035426 Roller, Flanged Blade Guide (Relube) Available in assemblies only. 1
057402 Roller, Flanged Blade Guide (Relube 1 1/2” Available in assemblies only. 1
blade)
A04925-364 Instruction Sheet, Blade Guide Roller 1
Replacement
53 036161 BOLT, BLADE GUIDE ROLLER (RELUBE ONLY) 1
54 P05060 FITTING, 1/4-28 GREASE (RELUBE ONLY) 1

Blade Guide Rollers & Arm WM doc 11/23/22 2-3

 Blade Guide Rollers & Arm
2 Blade Guide Assembly, Drive Side

2.2 Blade Guide Assembly, Drive Side

23 49
8
50
22 48 53
6
21 6 8
2
20 52
51
6 54
7
55
1
5 Optional Relube
9
24 Blade Guide Roller
6
25
8 11
4
3
17
41 12
13
26 38 14
42 16
31
32
30 37 15
29 10
36 17
27
28 33 19
34 18
44 35

39
45
40 3H0993-1C
46
43
47

REF PART # DESCRIPTION COMMENTS QTY.

1 016548 BLOCK, BOLT ON BLADE GUIDE MOUNT 1
2 003964 BRACKET WELDMENT, INNER BLADE GUIDE 1
MOUNT
3 F05011-4 WASHER, 3/8” SPLIT LOCK 2
4 F05007-7 BOLT, 3/8-16 X 1” HEX HEAD 2
003905 GUIDE ASSEMBLY, DRIVE SIDE BLADE 1
ROLLER
003910 Block Assembly, Blade Guide Mount 1
5 003911 Block Weldment, Blade Guide Mount Available in assemblies only. 1
6 F05010-17 Nut, 5/16-18 Hex 4
7 F05006-122 Screw, 5/16-18 x 1” Socket Head Flat 1
Point Stainless Steel Set
8 F05006-88 Bolt, 5/16-18 x 1” Hex Head Stainless 3
Steel
9 003913 Shaft Weldment, Drive Side Guide 1
10 003916 Plate, Blade Guide Deflector 1
11 F05006-101 Bolt, 5/16-18 x 3/4” Hex Head w/Flat & Lock 1
Washer
A04925 Roller Assembly, Blade Guide (standard) 1

2-4 WM doc 11/23/22 Blade Guide Rollers & Arm

 Blade Guide Rollers & Arm
Blade Guide Assembly, Drive Side 2
REF PART # DESCRIPTION COMMENTS QTY.
014299 Roller Assembly, Extended Blade Guide High-Performance Blade Guide 1
(optional for use with 1 1/2” blades) Kit requires LMS blade lube sys-
tem. Use kit 006325 to upgrade
both drive and idle side blade
guides to High-Performance. If
sawmill not already equipped
with LMS, add kit .
K07079 Bearing Kit, Blade Guide Rebuild 1
12 P04252 Washer, 5/8" White Felt 1
13 F04254-1 Ring, 1 1/8" Interior Retaining 1
14 015975 Bearing, R8-2RS Blade Guide Available in assemblies only. 2
15 P06455 Washer, 5/8" Gray Felt 1
F05005-105 Screw, 1/4-28 x 1/4” Socket Head 1
Cup Point Set Black Oxide
057407-1507 Instruction Sheet, Blade Guide 1
Rebuild
16 S04250 Roller, Flanged Blade Guide Available in assemblies only. 1
014298 Roller, Flanged Blade Guide (1 1/2” Available in assemblies only. 1
blade)
A04925-364 Instruction Sheet, Blade Guide Roller 1
Replacement
17 S04253 Spacer, Blade Guide 2
18 F05011-125 Washer, 1/2” Nord-Lock 1
19 F05008-10 Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 1
20 F05011-17 Washer, 5/16” SAE Flat 2
21 F05011-13 Washer, 5/16” Split Lock 2
22 F05006-93 Bolt, 5/16-18 x 1 1/4” Hex Head 2
23 035656 Bolt, Blade Guide Vertical Adjustment 1
24 F05010-17 Nut, 5/16-18 Hex 1
25 F05006-136 Bolt, 5/16-18 x 2 3/4” Hex Head Full Thread 1
006325 GUIDE KIT, HIGH-PERFORMANCE BLADE High-Performance Blade Guide 1
GUIDE (OPTIONAL) Kit requires LMS blade lube sys-
tem. Use kit 006325 to upgrade
both drive and idle side blade
guides to High-Performance. If
sawmill not already equipped
with LMS, add kit.
003927 Block Assembly, Drive Side Blade Guide 1
26 003915 Plate, Block Tilt Adjustment 1
27 003909 Block, Guide Block Mount 1
28 F05012-22 Pin, 3/16” x 5/8” Roll 2
29 F05011-3 Washer, 3/8” SAE Flat 1
30 F05011-4 Washer, 3/8” Split Lock 1
31 F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 1
32 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head 1
33 003914 Ball, 3/16” Dia. Nylon 2
34 F05011-14 Washer, 1/4” Split Lock 2
35 F05005-15 Bolt, 1/4-20 x 1/2” Hex Head 2
36 003994 Bolt, Blade Guide Block Mount 1
37 042867 Washer, #10 Brass 1
38 F05004-240 Bolt, #10-32 x 1 1/4” Hex Head -SS 1
39 044057 Screw, Lower Block Adjustment 1
40 F05004-200 Screw, #10-32 x 3/8” Socket Head -SS 1

Blade Guide Rollers & Arm WM doc 11/23/22 2-5

 Blade Guide Rollers & Arm
2 Blade Guide Assembly, Drive Side

REF PART # DESCRIPTION COMMENTS QTY.

41 F05011-17 Washer, 5/16” SAE Flat 1
42 F05011-13 Washer, 5/16” Split Lock 1
43 052355 Block, Blade Guide Wear (Standard for 1 1/4” 052355 blocks for use with 1 2
Blades) 1/4" blade provided as standard
equipment. EZ-Glide blocks
036347 are available for cus-
tomers who prefer this block.
052309 Block, Blade Guide Wear (Optional for 1 1/2” Bearing must be modified for 2
Blades) use with relube roller assem-
blies. Remove one seal from
each bearing, place open sides
facing each other and place
spacer 035411 between bear-
ings.
036347 Block Assembly, 1” Sq. EZ-Glide Wear 052355 blocks for use with 1 2
1/4" blade provided as standard
equipment. EZ-Glide blocks
036347 are available for cus-
tomers who prefer this block.
44 035799 Block, Blade Guide Alignment 1
45 F05011-20 Washer, #10 Split Lock 1
46 F05004-152 Screw, #10-32 x 5/8” Hex Head 1
47 044064 Adjustment Tool, Lower Guide Block 1
035248 Shim, .008" Blade Guide Block Spacer 1

Idle Side Blade Guide Parts ((See Section

2.1))
016568 ROLLER ASSEMBLY, BLADE GUIDE RELUBE 1
(OPTIONAL)
057405 ROLLER ASSEMBLY, EXTENDED BLADE High-Performance Blade Guide 1
GUIDE RELUBE (OPTIONAL FOR USE WITH 1 Kit requires LMS blade lube sys-
1/2” BLADES) tem. Use kit 006325 to upgrade
both drive and idle side blade
guides to High-Performance. If
sawmill not already equipped
with LMS, add kit .
057407 Bearing Kit, Relube Blade Guide Rebuild 1
48 P04252 Washer, 5/8" White Felt 1
49 F04254-1 Ring, 1 1/8" Interior Retaining 1
50 015975 Bearing, R8-2RS Blade Guide Available in assemblies only. 2
Bearing must be modified for
use with relube roller assem-
blies. Remove one seal from
each bearing, place open sides
facing each other and place
spacer 035411 between bear-
ings.
51 P06455 Washer, 5/8" Gray Felt 1
52 035411 Spacer, Blade Guide Bearing 1
057407-1507 Instruction Sheet, Blade Guide Rebuild 1
53 035426 Roller, Flanged Blade Guide (Relube) Available in assemblies only. 1
057402 Roller, Flanged Blade Guide (Relube 1 1/2” Available in assemblies only. 1
blade)
A04925-364 Instruction Sheet, Blade Guide Roller 1
Replacement
54 036161 BOLT, BLADE GUIDE ROLLER (RELUBE ONLY) 1
55 P05060 FITTING, 1/4-28 GREASE (RELUBE ONLY) 1

2-6 WM doc 11/23/22 Blade Guide Rollers & Arm

 Blade Guide Rollers & Arm
Blade Guide Arm Drive Assembly 2
2.3 Blade Guide Arm Drive Assembly

4 18
20
3
6
15

3H0538-2G
18 17
14
4
16
3 19
13 12
10 11
9 2
5
8
1

21
7

REF PART # DESCRIPTION COMMENTS QTY.

1 P09984 CHAIN, #25 X 20 1/4" 1
2 P09983 LINK, #25 MASTER 1
3 F05006-28 BOLT, 5/16-18 X 2 3/4" HEX HEAD GRADE 5 4
4 F05011-17 WASHER, 5/16" SAE FLAT 4
5 R01897 TUBE, 3/8" X 1/2" NEOPRENE 2.5ft
6 P07584 CLAMP, 1/2" COATED EMT 2
7 F05089-1 WRAP, 1/4" X 6" TIE 2
015989 DRIVE ASSEMBLY, BLADE GUIDE ARM 1
079215 Motor Assembly, Blade Guide Arm Replace- 1
ment
8 079214 Motor, Current Applications 1/30HP 1
12VDC Gear
061232 Gear Kit, Motor Replacement (Cur- 1
rent Application)
061234 Brush Kit, Gear Motor Replacement 1
(Current Application)
061233 Shaft Kit, Gear Motor Replacement 1
(Current Application)
9 F04875-1 Connector, 14 Gauge Butt 2
10 P09970 Sprocket, Gear Motor #25 14-Tooth 1
11 F05004-274 Screw, #10-24 x 1/4” Full Dog Point 2
Socket Set
12 F05004-60 Screw, #10-32 x 1/2" Hex Head 4
13 F05011-20 Washer, #10 Split Lock 4
A10365-296 Instruction Sheet, Blade Guide Arm 1
Motor

Blade Guide Rollers & Arm WM doc 11/23/22 2-7

 Blade Guide Rollers & Arm
2 Blade Guide Arm Drive Assembly

REF PART # DESCRIPTION COMMENTS QTY.

14 015939 Bracket, Blade Guide Arm Motor Mount 1
15 S09999 Roller, Blade Guide Arm Chain Idler 1
16 F05006-3 Bolt, 5/16-18 X 3 1/2" Hex Head Full Thread 1
17 S09996 Spacer, 5/16" I.D. X 1 1/2" 1
18 F05011-17 Washer, 5/16" SAE Flat 2
19 F05011-13 Washer, 5/16" Split Lock 1
20 F05010-58 Nut, 5/16-18 Hex Nylon Lock 1
21 S11617 COVER, BLADE GUIDE ARM MOTOR 1
S12029 GUARD, BLADE GUIDE ARM (G.S. ONLY) 1

2-8 WM doc 11/23/22 Blade Guide Rollers & Arm

 Blade Guide Rollers & Arm
Blade Guide Arm 2
2.4 Blade Guide Arm

2
1
2
4
5
11
3
11 5 4
6 12
13 9 3
12 13
5 10

5
8 10
6 5
7 89
5 7 3H0992-1

REF PART # DESCRIPTION COMMENTS QTY.

1 003972 BLADE GUIDE ARM WELDMENT 1
007040 BLADE GUIDE ARM WELDMENT (WIDE HEAD 1
ONLY)
2 W09067 BOLT, BLADE GUIDE ARM ROLLER CAM 4
3 F05011-5 WASHER, 5/8" SAE FLAT 4
4 F05011-26 WASHER, 5/8" EXTERNAL STAR 4
5 F05010-11 NUT, 5/8-18 HEX JAM 12
6 F05011-25 WASHER, 5/8" INTERNAL STAR 8
A09059 ROLLER ASSEMBLY, BLADE GUIDE ARM WITH 2
BEARING
7 S07989 Roller, Blade Guide Arm V-Groove Available in assemblies only. 1
8 P06030-1 Bearing, 6203-2NSL 5/8" I.D. Available in assemblies only. 1
9 F04254-8 Ring, 1.575” ID Beveled 5002-156 Retaining 1
A09932 ROLLER ASSEMBLY, BLADE GUIDE ARM WITH 2
BEARING AND SPROCKET
10 S09930 Roller, Blade Guide Arm Drive Available in assemblies only. 1
11 P06030-1 Bearing, 6203-2NSL 5/8" I.D. Available in assemblies only. 1
12 S09931 Sprocket, #25 26-Tooth Available in assemblies only. 1
13 F04254-8 Ring, 1.575” ID Beveled 5002-156 Retaining 1

Blade Guide Rollers & Arm WM doc 11/23/22 2-9

 Blade Wheel & Tensioner
3 Blade Drive Assembly

SECTION 3 BLADE WHEELS & TENSIONER

3.1 Blade Drive Assembly

LT30 D35/D36
LT40 D35/D36

19
16

17
13
12
18 15 15 14

10 8 20
3 1
4
11 6
13 15 6
5 2
27
9 21
7
10 5 22 23
3H0899-1B 25 26

24

REF PART # DESCRIPTION COMMENTS QTY.

016393 BEARING ASSEMBLY, BLADE WHEEL DRIVE 1
016392 Bearing Assembly, Cylindrical Drive Available in assemblies only. 1
1 016391 Housing, Blade Wheel Drive Bearing Available in assemblies only. 1
2 014005 Shaft, Blade Wheel Drive Available in assemblies only. 1
3 P10205 Bearing, Blade Wheel Drive #MU1308TV 1
4 016055 Bearing, Blade Wheel Drive #6308 C3 1
Open
5 F04254-17 Ring, 90mm Interior Retaining #I17 2
6 P10206 Seal, Drive Bearing #CR15890 2
7 016330 Fitting, 1/4” NPT x 3/8” Hose Barb Elbow 1
8 016331 Fitting, 1/4” NPT x 3/8” Hose Barb Vented 1
Elbow
9 016394 Hose, Oil Level Viewer 1
10 P649 Clamp, 7/32-5/8” Hose 2
11 017470 Decal, Oil Level Gauge 1
016393-555 Instruction Sheet, Drive Bearing Replacement 1
12 F05004-170 SCREW, 1/2-20 X 1 1/2” CONE POINT SET 1
13 F05008-108 BOLT, 1/2-20 X 1 1/4” HEX HEAD GRADE 5 4
14 F05008-49 BOLT, 1/2-20 X 1 3/4” HEX HEAD GRADE 5 1
15 F05010-16 NUT, 1/2-20 HEX JAM 6
014562 WHEEL KIT, DRIVE SIDE BLADE 1
16 016284 Wheel, Drive Side Blade Available in assemblies only. 1

3-1 WM doc 11/23/22 Blade Wheel & Tensioner

 Blade Wheel & Tensioner
Blade Drive Assembly 3
REF PART # DESCRIPTION COMMENTS QTY.
17 016270 Bushing, Modified 1 9/16” SD 1
18 S12892 Key, 3/8” x 3/8” x 1 5/8” 1
K12897-488 Instruction Sheet, Drive Side Blade Wheel 1
Replacement
19 P04185 BELT, BLADE WHEEL B57 1
20 BELT, DRIVE (See Section 5) FOR PART #
21 016531 SHEAVE, 5V12.5X3 BRAKE COMBO 1
22 016532 BUSHING, SF X 1 9/16” 1
23 014391 STRAP, METAL-BACKED BRAKE 1
24 017953 PLATE, BUSHING KEY RETAINER 1
25 F05011-4 WASHER, 3/8” SPLIT LOCK 3
26 F05007-27 BOLT, 3/8-16 X 3/4” HEX HEAD 3
27 014693 KEY, 3/8” X 3/8” X 1 7/8” 1

Blade Wheel & Tensioner WM doc 11/23/22 3-2

 Blade Wheel & Tensioner
3 Blade Drive Assembly

3.2 Blade Drive Assembly

LT30 G28 -- LT30HD G28

LT40 G28 -- LT40HD G28 Remote

19

16
17
13
12 OIL LEVEL

18 15 15 14 11 FULL

ADD
01 7470

3 10 8 20
1
13 4
5
15 6 2
5
13 21
9 7 6 22 25
10 23
3H0802-1C 24

REF PART # DESCRIPTION COMMENTS QTY.

016393 BEARING ASSEMBLY, BLADE WHEEL DRIVE 1
016392 Bearing Assembly, Cylindrical Drive Available in assemblies only. 1
1 016391 Housing, Blade Wheel Drive Bearing Available in assemblies only. 1
2 014005 Shaft, Blade Wheel Drive Available in assemblies only. 1
3 P10205 Bearing, Blade Wheel Drive #MU1308TV 1
4 016055 Bearing, Blade Wheel Drive #6308 C3 1
Open
5 F04254-17 Ring, 90mm Interior Retaining #I17 2
6 P10206 Seal, Drive Bearing #CR15890 2
7 016330 Fitting, 1/4” NPT x 3/8” Hose Barb Elbow 1
8 016331 Fitting, 1/4” NPT x 3/8” Hose Barb Vented 1
Elbow
9 016394 Hose, Oil Level Viewer 1
10 P649 Clamp, 7/32-5/8” Hose 2
11 017470 Decal, Oil Level Gauge 1
016393-555 Instruction Sheet, Drive Bearing Replacement 1
12 F05004-170 SCREW, 1/2-20 X 1 1/2” CONE POINT SET 1
13 F05008-108 BOLT, 1/2-20 X 1 1/4” HEX HEAD GRADE 5 4
14 F05008-49 BOLT, 1/2-20 X 1 3/4” HEX HEAD GRADE 5 1
15 F05010-16 NUT, 1/2-20 HEX JAM 6
014562 WHEEL KIT, DRIVE SIDE BLADE 1
16 016284 Wheel, Drive Side Blade Available in assemblies only. 1
17 016270 Bushing, Modified 1 9/16” SD 1
18 S12892 Key, 3/8” x 3/8” x 1 5/8” 1

3-3 WM doc 11/23/22 Blade Wheel & Tensioner

 Blade Wheel & Tensioner
Blade Drive Assembly 3
REF PART # DESCRIPTION COMMENTS QTY.
K12897-488 Instruction Sheet, Drive Side Blade Wheel 1
Replacement
19 P04185 BELT, BLADE WHEEL B57 1
20 BELT, DRIVE (SEE ENGINE MANUAL FOR PART (See Section 5) 1
#)
014692 PULLEY KIT, 2B124SK DRIVE (G28) 1
014691 PULLEY KIT, 3B124SK DRIVE 1
21 014689 Pulley, 2B124SK Drive (G28) Available in assemblies only. 1
22 014690 Bushing, 1 9/16" Type ’SK’ 1
014693 Key, 3/8” x 3/8” x 1 7/8” 1
23 014000 WHEEL, BRAKE 1
24 014003 BUSHING, 1 9/16” P1 1
25 014391 STRAP, METAL-BACKED BRAKE 1

Blade Wheel & Tensioner WM doc 11/23/22 3-4

 Blade Wheels & Tensioner
3 Idle Blade Wheel Assembly

3.3 Idle Blade Wheel Assembly

4 5

9
6

13
12
3

10
8

10
12
SM0254B
11
9
REF PART # DESCRIPTION COMMENTS QTY.
016120 WHEEL ASSEMBLY, IDLE SIDE BLADE 1
1 016013 Wheel, Idle Side Blade Available in assemblies only. 1
2 016014 Bearing, Idle Side Blade Wheel #5309-2RS, 1
C3, SRI-2 Grease
3 F04254-28 Ring, 100mm Internal Retaining Beveled 1
016441 SHAFT KIT, IDLE BLADE WHEEL 1
4 016397 Washer, 13/32” I.D. x 2 3/16 O.D. x 1/4” 1
5 F05007-64 Bolt, 3/8-16 x 1" Flat Head Socket 1
6 016398 Shaft, Idle Side Blade Wheel 1
7 P04185 BELT, BLADE WHEEL B57 1
8 016103 HOUSING, IDLE BLADE WHEEL SHAFT 1
9 F05008-53 BOLT, 1/2-20 X 1 1/2” HEX HEAD GRADE 5 2
10 F05010-16 NUT, 1/2-20 HEX JAM 4
11 F05008-111 BOLT, 1/2-20 X 3 3/4” HEX HEAD FULL THREAD 1
GRADE 2
12 S04253 SPACER, 1/2" I.D. FLANGED 2
13 F05011-9 WASHER, 1/2" SPLIT LOCK 1

3-5 WM doc 11/23/22 Blade Wheels & Tensioner

 Blade Wheels & Tensioner
Hydraulic Blade Tensioner Assembly 3
3.4 Hydraulic Blade Tensioner Assembly

18
13
15
16 17
14 11
7 9
19 20
10
21

11 22

12
5 6 23
1
4
2 3H0041E

8
3

REF PART # DESCRIPTION COMMENTS QTY.

A10136 HYDRAULIC BLADE TENSIONER ASSEMBLY 1
A12294 Handle Assembly, Hydraulic Blade Tensioner 1
Screw
1 S10056 Screw, Hydraulic Blade Tensioner Available in assemblies only. 1
2 S08174 Handle, Hydraulic Tensioner Screw 1
3 P08072 Sleeve, Plastic Handle 1
4 F05012-19 Pin, 3/16" x 7/8" Roll 1
5 P02720 Ball, 1/2" Steel 1
6 S10062 Block, Threaded Tensioner End Available in assemblies only. 1
7 P05060 Fitting, 1/4-28 Grease 1
A12294-518 Instruction Sheet, Tensioner Screw 1
8 F05006-43 Bolt, 5/16-18 X 7 1/2" Hex Head Grade 5 4
9 S10060 Piston, Hydraulic Tensioner Front 2 3/4" Long 1
10 S10061 Block, Piston Guide 1
003224 Seal Kit, Hydraulic Tensioner 1
5 P02720 Ball, 1/2" Steel 1
11 P10051 Seal, 1" Diameter 2
12 P10053 Wiper, 1" Diameter 1
13 P10377 Ring, 5/8" X 3/32" Square "O" 1
14 S10140 Block, Hydraulic Tensioner Gauge Mounting 1
15 P10052 Gauge, 3000 P.S.I. Hydraulic 1
16 P10065 Plug, Hydraulic Tensioner Fill 1
016329 Block Assembly, Rear Tensioner Piston 1
17 S10142 Block, Rear Tensioner Piston Available in assemblies only. 1

Blade Wheels & Tensioner WM doc 11/23/22 3-6

 Blade Wheels & Tensioner
3 Hydraulic Blade Tensioner Assembly

REF PART # DESCRIPTION COMMENTS QTY.

18 P10065 Plug, Hydraulic Tensioner Fill 1
19 S10059 Piston, Hydraulic Tensioner Rear 3 5/8" Long 1
20 S10089 Block, Rear Piston End 1
21 F05004-43 Bolt, #10-24 X 1" Socket Button Head 4
22 F05006-28 Bolt, 5/16-18 X 2 3/4" Hex Head Grade 5 4
23 P10147 Decal, Hydraulic Tension Caution 1
A10136-272 Instruction Sheet, Hydraulic Tensioner Installa- 1
tion

3-7 WM doc 11/23/22 Blade Wheels & Tensioner

 Saw Head
Middle Throat Screw 4
SECTION 4 SAW HEAD FRAME
4.1 Middle Throat Screw

1
SM0122B

REF PART # DESCRIPTION COMMENTS QTY.

1 F05007-18 SCREW, 3/8-16 X 1 1/4" OVAL POINT SOCKET 1
SET
2 F05010-29 NUT, 3/8-16 HEX JAM 1

Saw Head WM doc 11/23/22 4-1

 Saw Head
4 Water Lube Solenoid Valve

4.2 Water Lube Solenoid Valve

REF PART # DESCRIPTION COMMENTS QTY.

016280 Solenoid Valve, Water Lube Kit 1
1 F05004-60 Bolt, #10-32x1/2 HH 2
2 F05011-20 Washer, #10 Split Lock 2
3 F05011-18 Washer, #10 SAE Flat 2
4 P04682 Fitting, 3/8 Barb 1/4NPT Male 2
133071 Assy, Water Lube Solenoid Electrical 1
5 016140 Solenoid Valve, 2-Way NC 1/4 Port 12 VDC 1
6 F04875-13 Connector, TT-Tap 14-16Awg 2
7 F05708-21R Terminal, 1/4 18-22Ga Quick Female FI 2
8 R02374 Conduit, 1/2" Flex Loom 1
9 F05089-3 Tie Wrap, 3/16x5 1/2 UV Blk 1
024123 Diode Assy, Inductive Kick Protection 1
10 F05708-22R Terminal, 1/4 18-22 Ga Qk Male FI Reel 2
11 R01915-3_3 Wire, 18AWG Stranded Red GXL 1
12 R01950-4_2_14 Tubing, 1/4" IDx2.25 Heat Shrink 1
13 024032 Conn, 14-16 AWG Parallel Splice 2
14 E05909 DIODE, 1N4003 1
15 R01915-0_3 Wire,18AWG Stranded Black 1

4-2 WM doc 11/23/22 Saw Head

 Saw Head
Clutch/Brake Lever Assembly (D35/D36) 4
4.3 Clutch/Brake Lever Assembly (D35/D36)

21
24
23
25
13
12

11 2
26
27
21 8
10
28 15 9
22
16 1
7
17

18 6 3

18
4
20 19
14 3H0756-1D
3
5

REF PART # DESCRIPTION COMMENTS QTY.

016317 HANDLE ASSEMBLY, EXTENDED 1
CLUTCH/BRAKE
1 016295 Lever, Clutch/Brake Available in assemblies only. 1
2 P04211 Knob, Plastic Round 1
3 P737 Bushing, Clutch/Brake Pivot 2
4 P116 Washer, Clutch/Brake Pivot 1
5 F05012-49 Pin, 1/8" X 1 1/2" Cotter 1
6 015241 Extension Weldment, Clutch Handle 1
7 F05010-83 Nut, 7/16-20 Nylon Lock 1
8 F05007-55 Screw, 7/16-20 x 1 1/2” Socket Head 1
9 P11578 Rod End, 7/16-20 Left Hand Thread 1
10 F05010-87 Nut, 7/16-20 Hex Jam Left Hand Thread 1
11 015073 Rod, Clutch Extension 1
12 F05010-38 Nut, 7/16-20 Hex Jam 1
13 P11579 Rod End, 7/16-20 Right Hand Thread 1
14 P04107 Fitting, 3/16” Straight Grease 1
15 F05011-13 WASHER, 5/16” SPLIT LOCK 3
16 F05006-5 BOLT, 5/16-18 X 3/4” HEX HEAD 3
17 016296 PLATE WELDMENT, CLUTCH PIVOT 1
18 P737 BUSHING, CLUTCH/BRAKE PIVOT 2
19 P116 WASHER, CLUTCH/BRAKE PIVOT 1
20 F05012-49 PIN, 1/8" X 1 1/2" COTTER 1
21 F05010-83 NUT, 7/16-20 HEX NYLON LOCK 2
22 F05007-120 BOLT, 7/16-20 X 2” SOCKET HEAD 1
23 F05007-55 BOLT, 7/16-20 X 1 1/2" SOCKET HEAD 1
A11576 TURNBUCKLE ASSEMBLY, 3 1/2” 1
CLUTCH/BRAKE LEVER
24 P11579 Rod End, 7/16-20 Right Hand Thread 1

Saw Head WM doc 11/23/22 4-3

 Saw Head
4 Clutch/Brake Lever Assembly (D35/D36)

REF PART # DESCRIPTION COMMENTS QTY.

25 F05010-38 Nut, 7/16-20 Hex Jam 1
26 S12262 Turnbuckle, 3 1/2” Clutch/Brake Lever Available in assemblies only. 1
27 F05010-87 Nut, 7/16-20 Hex Jam Left Hand Thread 1
28 P11578 Rod End, 7/16-20 Left Hand Thread 1

4-4 WM doc 11/23/22 Saw Head

 Saw Head
Clutch Mount Assembly 4
4.4 Clutch Mount Assembly

8
7

6
1

2
3H0756-2B

REF PART # DESCRIPTION COMMENTS QTY.

1 F05010-83 NUT, 7/16-20 HEX NYLON LOCK 1
2 F05007-55 BOLT, 7/16-20 X 1 1/2" SOCKET HEAD 1
3 W12411 BRACKET, CLUTCH MOUNT 1
4 F05007-157 BOLT, 3/8-16 X 2 1/2” HEX HEAD 1
5 016316 SPACER, MOTOR MOUNT VIBRATION BUSH- 1
ING
6 P05032 BUSHING, MOTOR MOUNT VIBRATION 1
7 021276 WASHER, .40" I.D. X 1.44" O.D. X .18" THICK 1
8 F05010-10 NUT, 3/8-16 NYLON LOCK 1

Saw Head WM doc 11/23/22 4-5

 Saw Head
4 Brake Assembly

4.5 Brake Assembly

2
1

8
11
9
7 12
8

10

3H0366

REF PART # DESCRIPTION COMMENTS QTY.

014441 STRAP RETROFIT, SUPER BRAKE 1
1 F05010-10 Nut, 3/8-16 Nylon Lock 2
2 F05011-3 Washer, 3/8” SAE Flat 2
3 014395 Bracket, Upper Super Brake Strap Mount 1
4 F05007-127 Bolt, 3/8-16 x 1 1/4” Carriage Head Grade 5 2
5 F05012-81 Pin, 1/2” x 2 1/4” Clevis 1
6 F05012-1 Pin, 1/8” x 1” Cotter 1
7 014391 Strap, Upper Pivot Metal Brake 1
8 F05010-8 Nut, 1/2-13 Nylon Lock 2
9 F05008-88 Bolt, 1/2-13 x 1 3/4” Hex Head Grade 5 1
10 F05008-37 Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 1
11 S04195 Plate, Brake Strap Clamp 1
12 014392 Bracket, Lower Super Brake Strap Mount 1

4-6 WM doc 11/23/22 Saw Head

 Saw Head
Water Lube Assembly (Gas Only) 4
4.6 Water Lube Assembly (Gas Only)

2
3

4
5 3H1167

REF PART # DESCRIPTION COMMENTS QTY.

1 014642 BOTTLE ASSEMBLY, WATER LUBE W/CAP 1
061372 O-ring, Water Bottle Cap If the water bottle cap keeps 1
leaking, add this o-ring to the
cap. Leave the existing o-ring
installed.
2 014636 FITTING, 3/4FPT X 3/4MPT 1
3 014100 FITTING, WATER LUBE SHUTOFF VALVE 1
4 016086 FILTER, WATER LUBE 1
5 014113 FITTING, 5/8” NPT TO 3/8” HOSE BARB 1
6 R01885 TUBING, WATER LUBE 3/8” I.D. 7 ft.
CBOTTLE COVER, 5 GAL. WATER BOTTLE OPTIONAL 1
(NOT SHOWN)

Saw Head WM doc 11/23/22 4-7

 Saw Head
4 Water Lube Assembly (Diesel & Electric Only)

4.7 Water Lube Assembly (Diesel & Electric Only)

13

7
14

15 4
3
7

16
5
17
6 4
8
18
9 3H0281D
5 12

8
9
11
12
8

9
10

REF PART # DESCRIPTION COMMENTS QTY.

A11685 TRAY ASSEMBLY, FUEL TANK/WATER BOTTLE 1
1 S11684 Tray, Fuel Tank/Water Bottle 1
2 P11258 Strap, 24" Rubber (For Fuel Tank - See Engine 2
Manual)
3 P11668 Strap, 20" Rubber 2
4 F05005-34 Bolt, 1/4-20 X 1" Carriage Head 4
5 F05010-21 Nut, 1/4-20 Hex Lock 4
6 F05005-34 BOLT, 1/4-20 X 1" CARRIAGE HEAD 1
7 F05005-33 BOLT, 1/4-20 X 1/2" CARRIAGE HEAD 2
8 P07584 CLAMP, 1/2" EMT HOSE 3
9 F05011-11 WASHER, 1/4" SAE FLAT 3

4-8 WM doc 11/23/22 Saw Head

 Saw Head
Water Lube Assembly (Diesel & Electric Only) 4
REF PART # DESCRIPTION COMMENTS QTY.
10 F05010-21 NUT, 1/4-20 HEX LOCK 1
11 P07461 STRAP, 15" RUBBER 1
12 F05010-9 NUT, 1/4-20 SELF-LOCKING 2
13 014642 BOTTLE ASSEMBLY, WATER LUBE W/CAP 1
061372 O-ring, Water Bottle Cap If the water bottle cap keeps 1
leaking, add this o-ring to the
cap. Leave the existing o-ring
installed.
14 014636 FITTING, 3/4FPT X 3/4MPT 1
15 014100 FITTING, WATER LUBE SHUTOFF VALVE 1
16 016086 FILTER, WATER LUBE 1
17 014113 FITTING, 5/8” NPT TO 3/8” HOSE BARB 1
18 R01885 TUBING, WATER LUBE 3/8” I.D. 7 ft.

Saw Head WM doc 11/23/22 4-9

 Saw Head
4 Saw Head Decals

4.8 Saw Head Decals

B urn Ha za rd

Av oid c onta ct with any

par t of hot eng ine.
12
Failu re t o do so m ay
r esult in se riou s inju ry.
W ood -Miz er Pro du ct s, I nc .
8 00-5 25 -8 10 0 Re orde r # 01 441 9

18 17
15
16

19
Movin g Par ts Can Cr ush
An d Cut.
Make sur e all guar ds and cover s

5
M ovin g P arts C an Cr ush
A nd C ut.

M ake sure all guards and cover s

4 14
4
are in place and secure before ar e in place and secure before

13
operating this machine. oper ating this machine.
Fail ur e to do so will result in Failur e to do so will result in
serious injury. ser ious injury.
Woo d-M i zer P ro duct s, n
I c. Wo od- Mi zer P r oduct s, I nc.
80 0-5 25- 8100 R eor der #0332 54 8 00- 525- 810 0 R eor de r #033 254

1
3
11 11
9
8

6
10
2 7
Du
st
An
c onIns d
pe Ha
be ta c za Pr
Fa Ke of fo inm t pr rd o je
ilu e th re e nt oje ct
p
W re c e ea ch fin c til ile
lea s
in to sa wd r aw us ge e
80 ood
0- 525- Mi
- 810zer
se do of m rs
Pr ve so us t. e xi ill. e
0 odu re tin
cts, inj ma g
I nc. ur y
R y. re su
eor
der lt
#P
117
54

3H0589-8

REF PART # DESCRIPTION COMMENTS QTY.

1 P10147 DECAL, BLADE TENSION CAUTION 1
2 P11754 DECAL, SAWDUST CHUTE WARNING 1
3 P12373 DECAL, BLADE TENSION RANGES 1
4 033254 DECAL, BLADE COVERS DANGER 2
5 S11752 DECAL, BLADE DANGER ARROW RIGHT 1
6 S11762 DECAL, UP/DOWN CAUTION 1
7 P11779 DECAL, BLADE START/STOP 1
8 P11790 DECAL, BLADE TENSION INFO 1
9 P12879 DECAL, TRU-SHARP INFO 1
10 P11789 DECAL, BLADE ALIGNMENT INFO 1
11 P07452 DECAL, RED REFLECTIVE 2” ROUND 2
12 014419 DECAL, HOT ENGINE WARNING 1
13 003235 DECAL, WOOD-MIZER WEBSITE 1
14 065582 DECAL, 30 YEAR LOGO 1
15 065023 DECAL, LT40 IDLE SIDE BLACK EURO STRIPE 1
16 065025 DECAL, LT40/50 WHITE WOOD-MIZER LOGO 1
17 065026 DECAL, LT40/50 DRIVE SIDE BLACK EURO 1
STRIPE
18 065024 DECAL, LT40 WHITE EURO LOGO 1
19 074335 DECAL, LT15/70 WIDE LOGO (WIDE HEAD 1
ONLY)

4-10 WM doc 11/23/22 Saw Head

 Saw Head
Blade Housing Covers 4
4.9 Blade Housing Covers

3
5 6
14
11
15
4 13

2
9
10
12
10

8
3
7 6
12 2 4
1

12 5

3H0539-2F

REF PART # DESCRIPTION COMMENTS QTY.

015937 COVER ASSEMBLY, DRIVE SIDE BLADE HOUS- 1
ING WITH HANDLE
1 015911 Cover, Drive Side Blade Housing Available in assemblies only. 1
(Includes Cover Decal - (See
Section 4.2))
2 P08065 Handle, Blade Housing Cover 1
3 F05015-8 Screw, #8-32 X 3/8" Self-Tap 2
A12812 Pin Assembly, Cover Retainer 1
4 P05059 Pin, Safety Retainer 1
5 016030 Cable, 3/64” x 6” Lanyard 1
6 F05011-87 Washer, 1/2” ID x 1 1/8” OD x. 093” Rubber 1
A09419 COVER, IDLE SIDE BLADE HOUSING WITH 1
HANDLE
7 W09351 Cover, Idle Side Blade Housing Available in assemblies only. 1
(Includes Cover Decal - (See
Section 4.2))
2 P08065 Handle, Blade Housing Cover 1
3 F05015-8 Screw, #8-32 X 3/8" Self-Tap 2
A12812 Pin Assembly, Cover Retainer 1
4 P05059 Pin, Safety Retainer 1
5 016030 Cable, 3/64” x 6” Lanyard 1
6 F05011-87 Washer, 1/2” ID x 1 1/8” OD x. 093” Rubber 1
8 W07409 COVER, MIDDLE BLADE HOUSING 1
079509 COVER, MIDDLE BLADE HOUSING (WIDE HEAD 1
ONLY)

Saw Head WM doc 11/23/22 4-11

 Saw Head
4 Blade Housing Covers

REF PART # DESCRIPTION COMMENTS QTY.

9 F05005-1 BOLT, 1/4-20 X 3/4" HEX HEAD 18
10 S07522 HINGE, MIDDLE BLADE HOUSING COVER 2
11 F05010-9 NUT, 1/4-20 SELF-LOCKING HEX 4
12 021145 NUT, COVER TURN 3
13 S04433 PLATE, IDLE BLADE WHEEL GUARD 1
14 F05010-58 NUT, 5/16-18 HEX NYLON LOCK 6
15 F05006-5 BOLT, 5/16-18 X 3/4” HEX HEAD GRADE 2 6

4-12 WM doc 11/23/22 Saw Head

 Saw Head
Drive Belt Covers 4
4.10 Drive Belt Covers

1
1
7
1
8

1 2
6
4
5

3
3H0990-4B 1 1

REF PART # DESCRIPTION COMMENTS QTY.

1 F05005-134 BOLT, 1/4-20 X 3/4" HEX HEAD WITH CONICAL 13
WASHER
2 006028 GUARD WELDMENT, STANDARD LOWER For sawmills equipped with 1
DRIVE BELT standard manual clutch handle
only. See Autoclutch Option
manual for alternate guards.
See Section 4.14 for alternate
guard for sawmill equipped with
board return option.
3 006025 MOUNT WELDMENT, LOWER DRIVE BELT 1
4 F05005-15 BOLT, 1/4-20 X 1/2” HEX HEAD 2
5 F05011-11 WASHER, 1/4” SAE FLAT 2
6 059596 GUARD, STANDARD DRIVE PULLEY SIDE 1
7 059599 GUARD, DRIVE PULLEY TOP 1
8 074752 PLATE, LT40 BELT GUARD COVER 1

Saw Head WM doc 11/23/22 4-13

 Saw Head
4 Sawdust Chute

4.11 Sawdust Chute

3H0539-1 5
6

REF PART # DESCRIPTION COMMENTS QTY.

1 015466 CHUTE WELDMENT, SAWDUST 1
2 F05006-5 BOLT, 5/16-18 X 3/4” HEX HEAD GRADE 2 2
3 F05011-17 WASHER, 5/16” SAE FLAT 2
4 F05010-20 NUT, 5/16-18 SELF-LOCKING HEX 2
5 F05015-7 BOLT, #10-24 X 1/2” SELF-TAPPING 2
6 016727 TUBING, RUBBER SAWDUST 1
P11668 STRAP, 20” RUBBER W/HOOK 1
F05005-3 BOLT, 1/4-20 X 1 1/4” HEX HEAD FULL THREAD 1
F05011-11 WASHER, 1/4” SAE FLAT 1
F05010-21 NUT, 1/4-20 LOCK 1

4-14 WM doc 11/23/22 Saw Head

 Saw Head
Debarker Wire Box/Hole Plugs 4
4.12 Debarker Wire Box/Hole Plugs

1
4

2
3

3H0578-12

REF PART # DESCRIPTION COMMENTS QTY.

1 023616 BOX, DEBARKER WIRE STORAGE 1
2 F05007-29 BOLT, 3/8-16 X 2 3/4” HEX HEAD 2
3 F05011-3 WASHER, 3/8” SAE FLAT 2
4 F05010-10 NUT, 3/8-16 HEX NYLON LOCK 2
5 014537 PLUG, 13/32” PLASTIC HOLE 2

Saw Head WM doc 11/23/22 4-15

 Saw Head
4 Board Return Assembly (Optional)

4.13 Board Return Assembly (Optional)

23
22
4
5
2 3 2 6
4
18 15
8

20 7
21
1 14

9
19
MBR-M30/M40 Only
10

12
11
5
13

16 17
SM0331C

REF PART # DESCRIPTION COMMENTS QTY.

MBR-M30 RETURN OPTION, NON-SUPER BOARD (MAN- 1
UAL CLUTCH, LT30)
MBR-M40 RETURN OPTION, NON-SUPER BOARD (MAN- 1
UAL CLUTCH, LT40)
MBR-A30 RETURN OPTION, NON-SUPER BOARD (AUTO- 1
CLUTCH, LT30)
MBR-A40 RETURN OPTION, NON-SUPER BOARD (AUTO- 1
CLUTCH, LT40)
036693 Return Assembly, Optional Non-Super Board 1
1 036691 Mount Weldment, Board Return 1
2 F05007-1 Bolt, 3/8-16 x 3” Full Thread Hex Head 4
3 015336 Washer, 1/8” x 1 1/4” 2
4 F05010-10 Nut, 3/8-16 Hex Nylon Lock 4
5 F05011-3 Washer, 3/8” Flat 5
6 036692 Pin Weldment, Board Return Arm Sup- 1
port
7 P05060 Fitting, 1/4-28 Grease 1
8 F05012-16 Pin, 3/16 x 1 1/4” Roll 1
9 F05011-19 Washer, 5/8” x 15/16” x .094 Nylon 2
10 015210 Arm Weldment, Board Return 1
11 F05011-4 Washer, 3/8” Split 3
12 F05007-7 Bolt, 3/8-16 x 1” Hex Head 3

4-16 WM doc 11/23/22 Saw Head

 Saw Head
Board Return Assembly (Optional) 4
REF PART # DESCRIPTION COMMENTS QTY.
13 015652 Bracket Weldment, Board Return 1
14 015225 Rod, 5/8” x 7 5/8” 1
15 017604 Pin, 3/16” Retaining w/Chain 1
16 Board Return Table Parts ((See Section 8.5))
17 016072 Decal, Board Return Warning 1
Parts Listed Below Included in MBR-M30/M40
for Sawmills with Manual Clutch Lever Only:
18 006026 Guard Weldment, Clutch Handle 1
19 006025 Mount Weldment, Clutch Handle Guard 1
20 F05005-15 Bolt, 1/4-20 x 1/2” Hex Head 2
21 F05011-11 Washer, 1/4” SAE Flat 2

Saw Head WM doc 11/23/22 4-17

 Control & Battery Boxes
5 Control Assembly

SECTION 5 CONTROL & BATTERY BOXES

5.1 Control Assembly

30
4
32
4
18 31
7

9
4 4

2 13 8
3 12
19 15

10
10 23 16
14 14 17
4
11
6 5
24
5 4
21 1 6

23 11
4 22 25
20

26 28
27
29

3H1102
33

34

REF PART # DESCRIPTION COMMENTS QTY.

015764 COVER, SAWMILL CONTROL CONSOLE 1
036352 COVER, SAWMILL CONTROL CONSOLE 1
W/ACCUSET
069534 CONTROL BOX ASSEMBLY, G28 (2011) 1

069320 2 CONTROL BOX ASSEMBLY, G28 (2010) 1

069321 CONTROL BOX ASSEMBLY, D36 1

069322 CONTROL BOX ASSEMBLY, D35 (TIER2 ONLY) 1
1 016135 Box Weldment, Sawmill Control Available in assemblies only. 1
2 065375 Plate, Control Box Access Cover 1
3 065376 Gasket, Control Box Acces Cover 1
4 F05015-17 Screw, #10-24 x 1/2" Pan Head 32
5 015274 Gasket, Control Box Side Access 2
6 006473 Plate, Control Box Side Access 2
7 024458 Panel Assembly, Power Feed Control 1

5-1 WM doc 11/23/22 Control & Battery Boxes

 Control & Battery Boxes
Control Assembly 5
REF PART # DESCRIPTION COMMENTS QTY.
024396-1 Control Module, Power Feed SMT 1
052294 Suppressor Assembly, Power Feed 1
024387 Mosfet Module, Power Feed SMT 1
051571 Capacitor Assembly, Power Feed Filter 1
052363 Diode Assembly, Power Feed Replace- 1
ment
8 015278 Gasket, Rear Access Panel 1
9 N/A Front Control Panel & Wiring Harnesses ((See 1
Section 5.5))
10 N/A Drum Switches ((See Section 5.3)) 1
11 N/A Circuit Breakers ((See Section 5.4)) 1
12 F05004-3 Screw, #10-24 x 3/8” Phillips Pan Head 2
13 F05004-148 Screw, #10-24 x 3/8” Phillips Pan Head 4
Machine with Neo Washer
14 F05010-14 Nut, #10-24 Self Locking 6
15 F05007-27 Bolt, 3/8-16 x 3/4” Hex Head 2
16 F05011-3 Washer, 3/8” SAE Flat 2
17 F05010-19 Nut, 3/8” Self-Locking Hex 2
18 015304 Cover, Control Box Hinged 1
19 F05010-9 Nut, 1/4-20 Self Locking 2
20 F05005-181 Screw, 1/4-20 x 1 3/4” Flange Cap 1
21 015266 Gasket, Front Access Panel 1
22 015376 Panel, Control Box Front Access 1
23 F05011-69 Washer, 1/4” Internal Star Heavy Duty Lock 2
24 069349 Decal, Circuit Breaker ID (Std. 2010) 1
25 015236 MOUNT WELDMENT, STANDARD CONTROL 1
BOX
26 F05010-20 NUT, 5/16-18 SELF-LOCKING HEX 4
27 F05007-52 BOLT, 3/8-16 X 1” SOCKET HEAD 4
28 F05011-4 WASHER, 3/8” SPLIT LOCK 4
29 F05011-36 WASHER, 3/8” EXTERIOR STAR LOCK 4
30 015400 DECAL, FRONT OUTRIGGER WARNING 1
31 S11753 DECAL, EAR/EYE PROTECTION WARNING 1
32 S12117 DECAL, 800 NUMBER 1
33 036381 PLATE, PEDESTAL COVER 1
34 F05015-17 SCREW, #10-24 X 1/2" PAN HEAD 2

Control & Battery Boxes WM doc 11/23/22 5-2

 Control & Battery Boxes
5 Control Assembly (Tier4 Only)

5.2 Control Assembly (Tier4 Only)

4
44 43
18 42

9
7
4
4
2 13
3 12 8
15
19 16 4 24
14
10 28
10 25
17 33
14 34
11
6 5
23
29 35
21 26
1 27 30
11 32 36
4 37 31
22 20

38 40
41

3H1194-1
45
39 46

REF PART # DESCRIPTION COMMENTS QTY.

015764 COVER, SAWMILL CONTROL CONSOLE 1
036352 COVER, SAWMILL CONTROL CONSOLE 1
W/ACCUSET
073608 CONTROL BOX ASSEMBLY, D35 TIER4 1
1 016135 Box Weldment, Sawmill Control Available in assemblies only. 1
2 065375 Plate, Control Box Access Cover 1
3 065376 Gasket, Control Box Acces Cover 1
4 F05015-17 Screw, #10-24 x 1/2" Pan Head 32
5 015274 Gasket, Control Box Side Access 1
6 006473 Plate, Control Box Side Access 1
7 024458 Panel Assembly, Power Feed Control Kit 1
024396-1 Control Module, Power Feed SMT 1
052294 Suppressor Assembly, Power Feed 1
024387 Mosfet Module, Power Feed SMT 1
051571 Capacitor Assembly, Power Feed Filter 1
052363 Diode Assembly, Power Feed Replace- 1
ment
8 015278 Gasket, Rear Access Panel 1
9 N/A Front Control Panel & Wiring Harnesses ((See 1
Section 5.5))
10 N/A Drum Switches ((See Section 5.3)) 1

5-3 WM doc 11/23/22 Control & Battery Boxes

 Control & Battery Boxes
Control Assembly (Tier4 Only) 5
REF PART # DESCRIPTION COMMENTS QTY.
11 N/A Circuit Breakers ((See Section 5.4)) 1
12 F05004-3 Screw, #10-24 x 3/8” Phillips Pan Head 2
13 F05004-148 Screw, #10-24 x 3/8” Phillips Pan Head 4
Machine with Neo Washer
14 F05010-14 Nut, #10-24 Self Locking 6
15 F05007-27 Bolt, 3/8-16 x 3/4” Hex Head 2
16 F05011-3 Washer, 3/8” SAE Flat 2
17 F05010-19 Nut, 3/8” Self-Locking Hex 1
18 015304 Cover, Control Box Hinged 1
19 F05010-9 Nut, 1/4-20 Self Locking 2
20 F05005-181 Screw, 1/4-20 x 1 3/4” Flange Cap 1
21 015266 Gasket, Front Access Panel 1
22 015376 Panel, Control Box Front Access 1
23 069349 Decal, Circuit Breaker ID (Std. 2010) 1
073603 Box Assembly, Key Switch 1
24 078426 Control Box Weldment, Key/Hour 1
25 F05015-17 Bolt, #10-24x1/2 Ph Pan Hd, Type 23 4
26 033495 Panel Weldment, Side L.H. 1
27 015274 Gasket, Side Panel Control 97 1
28 033475 Grommet, 5/8 ID 3/16 GW Rubber 1
29 F05005-15 Bolt, 1/4-20x1/2 HH 2
30 F05010-9 Nut, 1/4-20 Keps 2
073597 Panel Assembly, Key Switch Box Frt 1
31 073598 Plate, Key Switch Box Front 1
32 073594 Decal, Key Switch 1
33 P04350 Switch, Key 1
34 015401 Digital Meter, Hour Rect Mount w/ 1
Gasket
35 F05015-28 Screw, #6-32x1/2 Plain PH T23 2
36 033488 Gasket, LMS Panel 1
37 015236 MOUNT WELDMENT, STANDARD CONTROL 1
BOX
38 F05010-20 NUT, 5/16-18 SELF-LOCKING HEX 4
39 F05007-52 BOLT, 3/8-16 X 1” SOCKET HEAD 4
40 F05011-4 WASHER, 3/8” SPLIT LOCK 4
41 F05011-36 WASHER, 3/8” EXTERIOR STAR LOCK 4
42 015400 DECAL, FRONT OUTRIGGER WARNING 1
43 S11753 DECAL, EAR/EYE PROTECTION WARNING 1
44 S12117 DECAL, 800 NUMBER 1
45 036381 PLATE, PEDESTAL COVER 1
46 F05015-17 SCREW, #10-24 X 1/2" PAN HEAD 2

Control & Battery Boxes WM doc 11/23/22 5-4

 Control & Battery Boxes
5 Drum Switches

5.3 Drum Switches

8
6

10
7 5
11 3
2

4
3H0421

REF PART # DESCRIPTION COMMENTS QTY.

E20440 SWITCH ASSEMBLY, UP/DOWN DRUM 1
1 E20440-B Switch, S12 Bulk Drum Available in assemblies only. 1
2 P12570 Spring, Drum Switch 1
3 P12500 Handle, Drum Switch Replacement 1
E20439 SWITCH ASSEMBLY, POWER FEED DRUM 1
4 E20439-B Switch, S11 Bulk Drum Available in assemblies only. 1
5 P12570 Spring, Drum Switch 1
6 P12500 Handle, Drum Switch Replacement 1
7 F05011-41 WASHER, #8 SAE FLAT 6
A20463 CUP ASSEMBLY, DRUM SWITCH GREASE 1
8 P20464 Cup, Plastic Container Available in assemblies only. 1
9 P20467 Decal, Grease Cup Label 1
10 P20466 Pad, Velcro Loop Available in assemblies only. 1
11 P20465 Pad, Velcro Hook Available in assemblies only. 1
P20468 Grease, High Temp Drum Switch Available in assemblies only. .025 lb

5-5 WM doc 11/23/22 Control & Battery Boxes

 Control & Battery Boxes
Circuit Breakers 5
5.4 Circuit Breakers

9 5
3 3

8
1 2
2

4
7
5 3H1051-2
7 6

5
REF PART # DESCRIPTION COMMENTS QTY.
015621 BREAKER ASSEMBLY, SAWMILL CONTROL 1
CIRCUIT
1 052826 Rail, Circuit Breaker 1
2 E20430 Breaker, 15 Amp Manual Reset 5
3 F05015-7 Screw, #10-24 x 1/2” Self-Tappipng 6
4 051981 BREAKER, 40A MANUAL RESET PANEL 1
MOUNT
5 021253 BOOT, CIRCUIT BREAKER 3
6 021256 BREAKER, 50A MANUAL RESET PANEL 1
MOUNT
7 F05004-3 SCREW, #10-24 X 3/8” PHILLIPS PAN HEAD 3
8 F05010-14 NUT, #10-24 SELF LOCKING 3
9 024246 BREAKER, 30A MANUAL RESET PANEL Supplied on D35/D36 or saw- 1
MOUNT mills equipped with Autoclutch.

Control & Battery Boxes WM doc 11/23/22 5-6

 Control & Battery Boxes
5 Front Panel Assembly & Harnesses

5.5 Front Panel Assembly & Harnesses

10
13
2
8
9 1
6 4

11
3H0420-3B

3
7
12

5
REF PART # DESCRIPTION COMMENTS QTY.
024210 PANEL ASSEMBLY, CONTROL FRONT (G28) 1
024211 PANEL ASSEMBLY, CONTROL FRONT 1
(D35/D36)
1 015270 Gasket, Front Panel 1
2 015302 Panel Weldment, Control 1
3 024450-1 Switch Assembly, Feed Rate 1
4 P06257 Knob, Feed Rate With Set Screw 1
5 024200 Switch, Toggle 1
6 P02575 Boot, Toggle Switch Rubber 1
7 P04350 Switch, Key 1
8 015401 Meter, Hour 1
9 F05015-28 Screw, #6-32 x 1/2” Plain PH T23 2
10 015271 Decal, Control Panel (G28) 1
015269 Decal, Control Panel (D35/D36) 1
11 015416 Board, LED Circuit (G28) 1
015409 Board, LED Circuit (D35/D36) 1
12 023147 Spacer, 1/2”-#6 Threaded 4
13 F05015-17 SCREW, #10-24 X 1/2" PAN HEAD 8
069531 HARNESS ASSEMBLY, UPPER WIRING (G28 1
2011)
069302 HARNESS ASSEMBLY, UPPER WIRING (G28 1
2010)
069305 HARNESS ASSEMBLY, UPPER WIRING (G38) 1
069303 HARNESS ASSEMBLY, UPPER WIRING (D36)
069304 HARNESS ASSEMBLY, UPPER WIRING (D35) 1
050399 Conduit, 1 1/4” x 58” Flex 1
024402 Connector, 1 1/4” Straight Male Metal Conduit 1

5-7 WM doc 11/23/22 Control & Battery Boxes

 Control & Battery Boxes
Front Panel Assembly & Harnesses 5
REF PART # DESCRIPTION COMMENTS QTY.
050679 HARNESS ASSEMBLY, LOWER WIRING (G28) 1
050678 HARNESS ASSEMBLY, LOWER WIRING 1
(D35/D36)
R02374 Conduit, 1/2” Expandable Black 41 in.
R02374 Conduit, 1/2” Expandable Black 42 in.

Control & Battery Boxes WM doc 11/23/22 5-8

 Control & Battery Boxes
5 Front Panel Assembly & Harnesses (Tier4 Only)

5.6 Front Panel Assembly & Harnesses (Tier4 Only)

7
2
8

3H1198-1 5

REF PART # DESCRIPTION COMMENTS QTY.

073610 PANEL ASSEMBLY, LT40 STANDARD TIER4 1
CONTROL FRONT (D35)
1 015270 Gasket, Front Panel 1
2 011298 Panel, LT40/50 Control Box Front 1
3 024450 Pot Assembly, Feed Rate Control Sawmill 1
4 P06257 Knob, Feed Rate With Set Screw 1
5 024200 Switch, Toggle 1
6 P02575 Boot, Toggle Switch Rubber 1
7 073593 Decal, Yanmar Tier 4 Cotrol Panel Front (D35) 1
8 073601 Controller, Yanmar Tier 4 Engine 1
073609 HARNESS ASSEMBLY, LT40NR D35.9 TIER 4 1
UPPER (D35)
050399 Conduit, 1 1/4” x 58” Flex 1
024402 Connector, 1 1/4” Straight Male Metal Conduit 1
073619 HARNESS ASSEMBLY, D35 TIER 4 LOWER 1
(D35)
R02374 Conduit, 1/2” Expandable Black 41 in.
R02374 Conduit, 1/2” Expandable Black 42 in.

5-9 WM doc 11/23/22 Control & Battery Boxes

 Control & Battery Boxes
Battery Box Assembly 5
5.7 Battery Box Assembly

3
2
12
11
1

40 7
36
35
8
35 36 6 9
37 5
39 21
8
4 15 14
18 10
23 22
26 17 18
26
34 30
27 29 19 38
31 20 36
16
23
22 25 24
28
13
32 33
41 300151D

REF PART # DESCRIPTION COMMENTS QTY.

1 061130 BATTERY, 12 VOLT 8A24 1

P12315 BATTERY, DEKA 12V, 24M77 800CCA 1000CA Available in assemblies only. 1

014667 BOX ASSEMBLY, LT30/LT40 BATTERY 1

2 F05092-16 Terminal, 5/16 1-2 Ga Ring NI Loose 2
3 F05011-13 Washer, 5/16” Split Lock 2
4 P09790 Retainer Loop, Battery 1
5 F05011-17 Washer, 5/16" SAE Flat 2
6 F05010-58 Nut, 5/16-18 Hex Nylon Lock 2
7 F05007-4 Bolt, 3/8-16 X 4" Hex Head Grade 2 2
8 F05011-3 Washer, 3/8" SAE Flat 4
9 F05011-36 Washer, 3/8" External Star 2
10 F05010-10 Nut, 3/8" Hex Nylon Lock 2
11 F05011-11 Washer, 1/4" SAE Flat 2
12 F05010-13 Nut, 1/4-20 Wing 2
13 015472 Box Weldment, Battery 1
006850 Block Assembly, Single Fuse 1
14 056999 Plate, Fuse Block Insulator 1
15 056997 Block, Fuse Mount Available in assemblies only. 1
16 056996 Block, 3/4” Upper Fuse 1
17 056998 Block, 3/4” Lower Fuse 1

Control & Battery Boxes WM doc 11/23/22 5-10

 Control & Battery Boxes
5 Battery Box Assembly

REF PART # DESCRIPTION COMMENTS QTY.

18 F05006-20 Screw, 5/16-18 x 1/2” Socket Button 3
Head
19 F05005-59 Screw, 1/4-20 x 1/2” Socket Button Head 1
20 F05005-101 Bolt, 1/4-20 x 1” Hex Head Grade 5 2
21 F05010-21 Nut, 1/4-20 Hex Lock 2
22 F05011-14 Washer, 1/4” Split Lock 2
23 F05005-123 Bolt, 1/4-20 x 3/4” Hex Head Grade 5 2
24 F05011-13 Washer, 5/16” Split Lock 2
25 F05006-102 Bolt, 5/16-18 x 3/4” Hex head Grade 5 2
26 052370-150 Fuse, 150A Mega 2
006854 Plate Assembly, Fuse Box Cover 1
27 006851 Cover, Fuse Box 1
28 F05006-1 Bolt, 5/16-18 x 1” Hex Head 2
29 F05010-20 Nut, 5/16-18 Hex Self-Locking 4
30 F05011-17 Washer, 5/16” SAE Flat 4
31 F05015-7 Screw, #10-24 X 1/2" Self-Tapping 4
32 P10364 Decal, 12 Volt Warning 1
33 006865 Decal, 150A Mega Fuse Link ID 1
34 050283 Gasket, Fuse Box Cover 1
35 P11764 Grommet, 5/8" Rubber Wire 2
36 052496 Plug, 1/2" Knockout Nylon 3
37 074198 Grommet, 3/4" ID 11 Gauge Thickness 2
38 074199 Grommet, 3/4" ID 16 Gauge Thickness 2
39 015774 LID WELDMENT, BATTERY BOX STANDARD 1
40 014774 DECAL, BATTERY BOX LID CAUTION 1
41 036309 CABLE ASSEMBLY, 1 GA X 16” FUSE TO BAT- 1
TERY POSITIVE

5-11 WM doc 11/23/22 Control & Battery Boxes

 Up/Down System
Saw Head Mount 6
SECTION 6 UP/DOWN SYSTEM
6.1 Saw Head Mount

13 2
3

6 7 1
4

9 5
10 8
11
10 12

SM0080D

REF PART # DESCRIPTION COMMENTS QTY.

1 W04099 V-BRACE, SAW HEAD MOUNT 1
2 F05006-5 BOLT, 5/16-18 X 3/4" HEX HEAD GRADE 5 12
F05006-93 BOLT, 5/16-18 X 1 1/4 HEX HEAD FULL THREAD 4
GRADE 5
3 M04096 PAD, PLASTIC SLIDE 6
016241 PAD, PLASTIC SLIDE LOWER W/CHAMFER 2
4 F05010-58 NUT, 5/16-18 NYLON LOCK 16
5 S07935 PLATE, V-BRACE WASHER 2
6 F05008-61 BOLT, 1/2-13 X 3 1/2" HEX HEAD GRADE 5 4
7 F05011-2 WASHER, 1/2” SAE FLAT 4
8 F05010-8 NUT, 1/2-13 NYLON LOCK 4
9 F05007-17 BOLT, 3/8-16 X 2" FULL THREAD 2
10 F05010-1 NUT, 3/8-16 HEX 4
11 F05011-3 WASHER, 3/8" SAE FLAT 2
12 F05011-4 WASHER, 3/8" SPLIT LOCK 2
13 017715 CAP, .281” X 1/2” BLACK VINYL 3

Up/Down System WM doc 11/23/22 6-1

 Up/Down System
6 Blade Height & Quarter Scales

6.2 Blade Height & Quarter Scales

13

8
3H0961
12
7
1
10

3
4 6 5 16 18
19
STOP
1 21 17

2 20
2

5
4
9 22
6
3

8 BLADE
4
Stop
5 4

6
4

5
Start
P11779

15

13

11 21 19
20

14

REF PART # DESCRIPTION COMMENTS QTY.

A12030 SCALE RETROFIT, FIXED WITH POINTER 1
K11998 Scale Kit, Fixed With Pointer Available in assemblies only. 1
A12022 Scale Assembly, Fixed Available in assemblies only. 1
1 W11996 Bracket, Scale Mounting 1
2 036666 Plate, Movable Scale Stop 1
3 S11989 Scale, 35" Quarter 1
4 S11774 Decal, 35" Standard Quarter 1
Scale
P12819 Decal, 35" Grade Hardwood 1
Quarter Scale
5 S11988 Scale, 35" Inch 1
6 S11773 Decal, 35" Inch 1
7 S04805 Strap, Scale Hold-Down 1
8 F05012-14 Pin, 1/8" X 5/8" Roll 1
9 F05005-64 Screw, 1/4-20 X 5/8" Wing 1
10 F05005-1 Bolt, 1/4-20 x 1/2” Hex Head 2
11 F05011-11 Washer, 1/4" SAE Flat 1

6-2 WM doc 11/23/22 Up/Down System

 Saw Head Mount & Scales
Blade Height & Quarter Scales 6
REF PART # DESCRIPTION COMMENTS QTY.
12 F05011-22 Washer, 1/4" X .020 Thick Nylon 2
Flat
13 F05010-9 Nut, 1/4-20 Hex Self-Locking 2
14 F05005-70 Screw, 1/4-20 X 3/4" Flat Socket 1
Head
038591 Pointer Assembly, Fixed Scale 1
15 038586 Bracket, Fixed Scale Pointer Mount 1
16 038585 Pointer, Fixed Scale 1
17 F05004-3 Screw, #10-24 X 3/8" Phillips Head 2
18 F05010-14 Nut, #10-24 Hex Self-Locking 2
19 F05005-134 Bolt, 1/4-20 x 3/4” with Conical Washer 2
20 F05011-17 Washer, 5/16” SAE Flat 2
21 F05010-6 Nut, 5/16-18 Hex Lock 2
F05005-15 Bolt, 1/4-20 X 1/2" Hex Head Grade 2 1
A12030-370 Instruction Sheet, Fixed Scale Retrofit 1
K12064 DECAL KIT, METRIC SCALE 1
S11711 Decal, Metric 1
P12040-1 Decal, Metric 16-40mm 1
P12040-2 Decal, Metric 45-63mm 1
22 P11779 DECAL, CLUTCH HANDLE OPERATION 1

Saw Head Mount & Scales WM doc 11/23/22 6-3

 Up/Down System
6 Up/Down Chain & Sprockets

6.3 Up/Down Chain & Sprockets

1
3 2

3
4

2
1 4

5
6

3H0654-1C

8
11

10

8
9

REF PART # DESCRIPTION COMMENTS QTY.

016020 SPROCKET KIT, UP/DOWN IDLER #50-2 1
1 016019 Sprocket, Up/Down Idler ‘98 2
2 016018 Spacer, 50-2 Idler '98 4
016020-541 Instruction Sheet, Up/Down Idler Retrofit 1
3 F05009-6 BOLT, 5/8-11 X 5" HEX HEAD GRADE 2 2
4 F05010-96 NUT, 5/8-11 JAM NYLON LOCK 2
5 015259 CHAIN, #50-2 X 75.625" UP/DOWN 1
6 015258 LINK, #50-2 MASTER 2
015456 TENSIONER ASSEMBLY, UP/DOWN CHAIN 1
7 015188 Bracket, Up/Down #50 Chain Tensioner Available in assemblies only. 1
8 F05011-2 Washer, 1/2" SAE Flat 2
9 F05010-8 Nut, 1/2-13 Hex Nylon Lock 1
10 016516 Spring, 1” OD x 1” Long x .125” Wire Compr. 1
11 016515 Spacer, Up/Dn Chain Tensioner 1

6-4 WM doc 11/23/22 Up/Down System

 Up/Down System
Up/Down Assembly 6
6.4 Up/Down Assembly

21
1

2
3
5 4
19
18 6
13
7
8
15
16
22
23
17
8 7
9
6 16

14
20
10

11
12
24
25
3H1052 26
REF PART # DESCRIPTION COMMENTS QTY.
008722 UP/DOWN DRIVE ASSEMBLY 1
1 053683 Motor, 3/4HP 12VDC Electric 1
061794 Brush Kit, .5-.75 12V DC Motor 1
2 008721 Bracket, Up/Down Motor Mount 1
3 F05011-11 Washer, 1/4” SAE Flat 3
4 F05011-14 Washer, 1/4” Split Lock 3
5 F05005-101 Bolt, 1/4-20 X 1" Hex Head Grade 5 3
6 F05007-7 Bolt, 3/8-16 x 1” Hex Head 8
7 F05011-4 Washer, 3/8” Split Lock 8
8 F05011-3 Washer, 3/8” SAE Flat 12
9 074124 Gear Box, Up/Down Grove 1
10 014158 Plate, Gear Box Spacer 1
11 F05007-64 Bolt, 3/8-16 x 1” Flat Socket Head 4
12 014088 Pulley, Up/Down 1
036213 Belt/Pulley Kit, Standard Up/Down 1
13 036204 Pulley, AK22 x 1/2” 1
14 014089 Belt, 4L270 1
016094 Shaft Kit, Up/Down Super 1
15 016031 Shaft, Up/Down Sprocket 1
16 F05005-105 Screw, 1/4-28 x 1/4” Socket Head Cup 3
Point
17 S04124 Key, 1/4” Square x 1 11/16” Long 1

Up/Down System WM doc 11/23/22 6-5

 Up/Down System
6 Up/Down Assembly

REF PART # DESCRIPTION COMMENTS QTY.

18 014090 Bearing, Flanged Up/Down 1
19 014108 Plate, Bearing Spacer 1
20 S31027 Key, 3/16” Square x 1” Long 1
21 024431 Decal, Disconnect Motor Leads Warning 1
22 F05007-27 BOLT, 3/8-16 X 3/4” HEX HEAD 4
23 F05011-4 WASHER, 3/8” SPLIT LOCK 4
24 F05011-17 WASHER, 5/16" SAE FLAT 4
25 F05011-13 WASHER, 5/16” SPLIT LOCK 4
26 F05006-102 BOLT, 5/16-18 X 3/4" HEX HEAD GRADE 5 4
L04869-4 OIL, 8 OZ. MOBIL SHC634 BOTTLED SYN- 24 oz. required for complete oil 1
THETIC GEAR replacement.

6-6 WM doc 11/23/22 Up/Down System

 Feed System & Track Rollers
Upper Track Rollers And Wipers 7
SECTION 7 FEED SYSTEM & TRACK ROLLERS
7.1 Upper Track Rollers And Wipers

15
18
3
6 19

10
11
5
16
2
3 15 20 17 1
4
6
1
8
4
5
7 3

1
12 3H0125F

13
9

REF PART # DESCRIPTION COMMENTS QTY.

1 012797 ROLLER, TRACK CAM BEARING 5
2 016510 SHIM, 5/8” X 1” X .062” 2
3 F05010-11 NUT, 5/8-18 HEX JAM 5
4 F05008-5 SCREW, 1/2-13 X 1 1/4” OVAL POINT SET 2
5 F05010-31 NUT, 1/2-13 HEX JAM 2
6 F05005-64 SCREW, 1/4-20 X 5/8" THUMB 4
7 M04113 WIPER, PLASTIC TRACK 2
8 012999 HOUSING, UPPER TRACK ROLLER REAR 1
9 016285 HOUSING, UPPER TRACK ROLLER FRONT 1
10 F05007-2 BOLT, 3/8-16 X 1 1/4” HEX HEAD 2
11 F05010-29 NUT, 3/8-16 HEX JAM 2
12 016501 BLOCK, UPPER ROLLER PIVOT 1
13 F05013-3 BOLT, 3/4-10 X 4” HEX HEAD GRADE 5 1
14 F05010-80 NUT, 3/4-10 SELF LOCKING 1
110612 COVER ASSEMBLY, LT40 TRACK 1
15 110609 Cover, Middle Track, LT40 Available in assemblies only. 1
16 110611 Retainer, Felt Oiler Available in assemblies only. 1
17 F05005-113 Bolt, 1/4-20x3/4 Carriage 4
18 F05010-69 Nut, 1/4-20 Nylock 4
19 F05011-11 Washer, 1/4 SAE Flat 4
20 S09915 Felt, Middle Track Oiler LT40/50/70 1

Feed System & Track Rollers WM doc 11/23/22 7-1

 Feed System & Track Rollers
7 Power Feed Assembly

7.2 Power Feed Assembly

7
15
3
16 1
5

17 21

3
24

8 23
11
14 22
13
12
10
6 9

3H0036I
18
A11603_M

25
19
20
REF PART # DESCRIPTION COMMENTS QTY.
A11603 POWER FEED ASSEMBLY 1
1 006747 Motor, Power Feed 1
061794 Brush Kit, 12V Motor (2008) 1
F05006-40 Screw, 5/16-18 x 3/8” Socket Head Set Oval 2
Point
2 066991 Mount Weldment, LT35 Power Feed 1
3 P06030-1 Bearing, 5/8" 6203-2NSL 2
079800 Shaft Upgrade, Power Feed 1
4 079798 Shaft Weldment, Power Feed, Threaded Available in assemblies only. 1
5 079799 Spacer, Bearing, Power Feed 1
6 F05010-101 Nut, 5/8-18 Nyl Jam 1
7 S31027 Key, 3/16” Square x 1” Long 1
8 P04343 Pulley, 8" Power Feed 1
9 P04031 Belt, 4L280 V 1
10 S09579 Pulley, Power Feed Motor 1
11 F05007-12 Screw, 3/8-16 X 1/2" Cup Point Socket Set 2
12 F05005-101 Bolt, 1/4-20 X 1" Hex Head Grade 5 3
13 F05011-14 Washer, 1/4" Split Lock 3

7-2 WM doc 11/23/22 Feed System & Track Rollers

 Feed System & Track Rollers
Power Feed Assembly 7
REF PART # DESCRIPTION COMMENTS QTY.
14 F05011-11 Washer, 1/4" SAE Flat 3
15 012797 Bearing, 1 1/2” Cam Follower 1
16 F05011-5 Washer, 5/8" SAE Flat 6
17 F05010-11 Nut, 5/8-11 Hex Jam 1
18 W11613 Guard, Power Feed Belt 1
19 F05011-14 Washer, 1/4" Split Lock 2
20 F05005-7 Bolt, 1/4-20x2 1/2 HH ECN 35988:F05005-7 Replaced 2
(2) F05005-32, Added (2)
F05011-11
21 024431 Decal, Disconnect Motor Leads Warning 1
22 F05007-6 Bolt, 3/8-16 X 3 1/2" Hex Head Grade 8 2
23 F05011-36 Washer, 3/8" Star Lock 2
24 F05011-3 Washer, 3/8" SAE Flat 2
25 F05011-11 Washer, 1/4 SAE Flat 1 2

Feed System & Track Rollers WM doc 11/23/22 7-3

 Power Feed System
7 Feed Chain/Stop

7.3 Feed Chain/Stop

19 18 14
13
9
12

10

11 13
7

6
8 2
8 2
7
1 15
17
5
4
SM0353
3
16

REF PART # DESCRIPTION COMMENTS QTY.

1 014744 CHAIN, #40 X 215.5" LT30 FEED 1
014745 CHAIN, #40 X 267.5" LT40 FEED 1
2 P04200 LINK, #40 MASTER 2
3 015721 TENSIONER WELDMENT, POWER FEED CHAIN 1
4 F05011-2 WASHER, 1/2” SAE FLAT 3
5 F05011-9 WASHER, 1/2” SPLIT LOCK 3
6 F05008-128 BOLT, 1/2-13 X 1” HEX HEAD GRADE 8 3
7 F05010-16 NUT, 1/2-20 HEX JAM 2
8 F05011-9 WASHER, 1/2" SPLIT LOCK 2
9 006686 BRACKET WELDMENT, REAR FEED STOP 1
K09630 STOP KIT, RUBBER CARRIAGE 2
10 P12165 Stop, Rubber Carriage 1
11 W09293 Pin, Rubber Carriage Stop 1
12 F05012-21 Pin, 3/16" X 1" Cotter 1
13 F05005-134 BOLT, 1/4-20 X 3/4” WITH CONICAL WASHER 1
14 057822 PLATE, BED TUBE END W/LIGHT MOUNT 1
15 015008 BRACKET, FRONT FEED CHAIN MOUNT 1
16 F05007-87 BOLT, 3/8-16 X 1” HEX HEAD GRADE 5 2
17 F05010-10 NUT, 3/8-16 HEX NYLON LOCK 2
18 006688 GROMMET, 6 1/2” LIGHT MOUNTING 1
19 006391 LIGHT, 8 DIODE LED TAIL 1

7-4 WM doc 11/23/22 Power Feed System

 Power Feed System
Lower Track Rollers 7
7.4 Lower Track Rollers

4 5
7
10
9

6
8
4 5

5
4

3H0812B

3
11 1

REF PART # DESCRIPTION COMMENTS QTY.

012995 ROLLER ASSEMBLY, LOWER TRACK 2
1 012982 Bracket, Lower Track Roller Mounting Available in assemblies only. 1
2 012797 Roller, Track Cam Bearing 1
3 F05010-11 Nut, 5/8-18 Hex Jam 1
4 F05010-5 Nut, 5/8-11 Hex 4
5 F05011-118 Washer, 5/8" Split Lock Grade 8 4
6 033374 Bracket Weldment, Lower Track Roller Wiper 1
7 033375 Wiper, Round Gray Felt 1
8 F05008-2 BOLT, 1/2-13 X 2 1/4” HEX HEAD FULL THREAD 2
9 F05010-31 NUT, 1/2-13 HEX JAM 2
10 F05010-3 NUT, 1/2-13 HEX LOCK 2
11 F05008-61 BOLT, 1/2-13 X 3 1/2" HEX HEAD GRADE 5 2

Power Feed System WM doc 11/23/22 7-5

 Bed Frame Assembly
8 Bed Rail Assembly

SECTION 8 BED FRAME ASSEMBLY

8.1 Bed Rail Assembly

REF PART # DESCRIPTION COMMENTS QTY.

014666 BED ASSY, LT40 97 1
1 Bed Rail Assembly, Front And Rear (See Section 8.2) 1
2 Bed Rail Assembly, Middle Front (See Section 8.3) 1
3 Bed Rail Assembly, Middle Rear (See Section 8.4) 1
4 Pivot Bed Rail Assembly (See Section 8.6) 1
5 Log Side Support Assembly (See Section 8.7) 4
6 Safety Chain Assembly (See Section 8.8) 1
7 Log Clamp (See Section 8.12) 1

8-1 WM doc 11/23/22 Bed Frame Assembly

 Bed Rail Assembly, Front And Rear 8
8.2 Bed Rail Assembly, Front And Rear

REF PART # DESCRIPTION COMMENTS QTY.

1 016898 Cover, 36-1/4 Rail SS 2
2 f05006-10 Bolt, 5/16-18x2 1/2 HH Gr2 6
3 f05010-6 Nut, 5/16-18 Swaged Hex 6
a09774 Bedrail Assy, 1996 Rear Non-Hyd 1
4 s09034 Block, 3/4x3/4x1 1
5 f05010-187 Nut, 5/8-11 Square Pilot Weld 2
6 f05010-5 Nut, 5/8-11 Hex 2
7 s13006 Bolt, Bed Rail Adj LT50 2
8 s09102 Tube, 2x4 Long Adj Bed Rail 1
9 s04030 Pin, 5/8x3 1/2 1
10 s04058 Plate, 1/8x1 3/4x3 3/4 1
11 f05005-134 Bolt, 1/4-20x3/4 W/Conical Washer 1
12 038843 Plate, Formed 2x4 Bed Cap 2
13 f05008-94 Bolt, 1/2-13x3 1/2 Carriage 1
14 f05010-8 Nut, 1/2-13 Nyl Hex Lock 4
15 f05011-2 Washer, 1/2 SAE Flat 7
16 f05008-78 1/2-13 x 4 HHB GR5 ZINC 3
a09564 Bedrail Assy, 1996 Front Non-Hyd. 2
17 s09034 Block, 3/4x3/4x1 1
18 f05010-187 Nut, 5/8-11 Square Pilot Weld 2
19 f05010-5 Nut, 5/8-11 Hex 2
20 s13006 Bolt, Bed Rail Adj LT50 2

WM doc 11/23/22 8-1

 8 Bed Rail Assembly, Front And Rear

REF PART # DESCRIPTION COMMENTS QTY.

21 s09334 Tube, Ramp Mount 1
22 s04058 Plate, 1/8x1 3/4x3 3/4 2
23 s04030 Pin, 5/8x3 1/2 1
24 s09102 Tube, 2x4 Long Adj Bed Rail 1
25 079096 Pin Assy, Rest, Manual (See Section 8.10) 1

8-2 WM doc 11/23/22

 Bed Frame Assembly
Bed Rail Assembly, Middle Front 8
8.3 Bed Rail Assembly, Middle Front

10
11
12

7
8

7 1
8

3
4 9
2
9
13 5
6 3
8
4

SM0235B
5

REF PART # DESCRIPTION COMMENTS QTY.

A09566 BED RAIL ASSEMBLY, FRONT MIDDLE 1
1 S09103 Bed Rail Tube, Short Available in assemblies only. 1
2 S04030 Pin, Ramp Mount 1
3 F05010-84 Nut, 5/8-11 Pilot Weld 2
4 F05010-5 Nut, 5/8-11 Hex 2
5 S13006 Bolt, Bed Rail Adjustment 2
6 S04058 Plate, Bed Rail End Cap Available in assemblies only. 2
7 F05008-78 BOLT, 1/2-13 X 4" HEX HEAD GRADE 5 2
8 F05011-2 WASHER, 1/2" SAE FLAT 4
9 F05010-8 NUT, 1/2-13 NYLON LOCK 2
A09956 COVER ASSEMBLY, STAINLESS STEEL BED 1
RAIL (LONG)
10 S09944 Cover, Stainless Steel Bed Rail Available in assemblies only. 1
11 F05006-10 Bolt, 5/16-18 X 2 1/2" Hex Head 3
12 F05010-6 Nut, 5/16-18 Hex Lock 3
13 015970 WRENCH, BED RAIL ADJUSTMENT 1

Bed Frame Assembly WM doc 11/23/22 8-3

 Bed Frame Assembly
8 Bed Rail Assembly, Middle Rear

8.4 Bed Rail Assembly, Middle Rear

16

15 14

2
4
3

13 16
12
1
12

15

8 12
11
12
6 5

9
10 13
7
8
11
250038D
9

17

REF PART # DESCRIPTION COMMENTS QTY.

A09565 BED RAIL ASSEMBLY, REAR MIDDLE 1
1 014640 Bed Rail Tube, Short Available in assemblies only. 1
2 014639 Block, Log Stop w/Threaded Hole Available in assemblies only. 1
3 F05007-17 Bolt, 3/8-16 x 1 1/2 Full Thead Hex Head 1
4 F05010-29 Nut, 3/8-16 Hex Jam 1
5 S04030 Pin, Ramp Mount 1
6 S09334 Tube, Ramp Retainer Mount Available in assemblies only. 1
7 F05010-84 Nut, 5/8-11 Pilot Weld 2
8 F05010-5 Nut, 5/8-11 Hex 2
9 S13006 Bolt, Bed Rail Adjustment 2
10 S04058 Plate, Bed Rail End Cap Available in assemblies only. 2
11 F05008-78 BOLT, 1/2-13 X 4" HEX HEAD GRADE 5 2
12 F05011-2 WASHER, 1/2" SAE FLAT 4
13 F05010-8 NUT, 1/2-13 NYLON LOCK 2
A09956 COVER ASSEMBLY, STAINLESS STEEL BED 1
RAIL (LONG)
14 S09944 Cover, Stainless Steel Bed Rail Available in assemblies only. 1
15 F05006-10 Bolt, 5/16-18 X 2 1/2" Hex Head 3
16 F05010-6 Nut, 5/16-18 Hex Lock 3
17 015970 WRENCH, BED RAIL ADJUSTMENT 1

8-4 WM doc 11/23/22 Bed Frame Assembly

 Bed Frame Assembly
Leg Assembly (Stationary) 8
8.5 Leg Assembly (Stationary)

3
5

3H0413D

18 6

2
9
17
10 65

8
11

13 15 4
7
1
14 16
12

DCS ONLY

REF PART # DESCRIPTION COMMENTS QTY.

See Form #847 or diagram below for stationary
sawmill foot anchor locations
See Form #359 for stationary sawmill w/bed exten-
sion foot anchor locations
1 W09513 LEG, LONG STATIONARY (1 REQ’D FOR LT30; 3 1/3
REQ’D FOR LT40)
2 015091 LEG, LONG STATIONARY W/BOARD RETURN 1
TABLE BRACKET
3 F05007-113 BOLT, 3/8-16 X 5” CARRIAGE HEAD 8/12
4 F05007-2 BOLT, 3/8-16 X 1 1/4" HEX HEAD (REQ'D FOR 4
REAR LT40 ONLY)
5 F05011-3 WASHER, 3/8” SAE FLAT 8/16
6 F05010-10 NUT, 3/8-16 HEX NYLON LOCK 8/16
7 W09515 LEG, SHORT STATIONARY 2
8 F05007-2 BOLT, 3/8-16 X 1 1/4" HEX HEAD 8
9 F05010-10 NUT, 3/8-16 HEX NYLON LOCK 8
10 W09517 LEG, FRONT STATIONARY 1
11 065935 Leg Weldment, Festoon Stationary Front 1
12 F05008-88 Bolt, 1/2-13 x 1 3/4” Full Thread Hex Head 1
Grade 5
13 F05010-3 Nut, 1/2-13 Swaged Hex 1
14 F05010-35 Nut, 1/2-13 Free Hex 1
15 F05011-2 Washer, 1/2” SAW Flat 2
16 F05011-9 Washer, 1/2” Split Lock 1
17 F05009-11 BOLT, 5/8-11 X 5 1/2" HEX HEAD GRADE 5 2
18 F05010-4 NUT, 5/8-11 HEX LOCK 2

Bed Frame Assembly WM doc 11/23/22 8-5

8-6
8

015091 W09513 W09513

Leg Assembly (Stationary)
Bed Frame Assembly

W09513

W09517
W09515 W09515

WM doc 11/23/22
015091 W09513 W09513

W09513

W09517 (All Except LT70DCS) W09515

065937 (LT70DCS Only) W09515
SM0426

Bed Frame Assembly

 Bed Frame Assembly
Pivot Bed Rail Assembly 8
8.6 Pivot Bed Rail Assembly

16
16 15
17

17
12
5
1

2 9 11
3
8 12
10
12
4
3H0128C 7
6 1413

REF PART # DESCRIPTION COMMENTS QTY.

A13015 PIVOT BED RAIL ASSEMBLY (LT40) 2
012993 PIVOT BED RAIL ASSEMBLY (LT30) 2
1 W13014 Pivot Bed Rail Weldment (LT40) Available in assemblies only. 1
012992 Pivot Bed Rail Weldment (LT30) Available in assemblies only. 1
2 F05010-84 Nut, 5/8-11 Pilot Weld 2
3 F05010-5 Nut, 5/8-11 Hex 2
4 S13006 Bolt, Bed Rail Adjustment 2
5 W13090 Bracket, Pivot Rail Mounting 1
6 F05008-50 Bolt, 1/2-13 x 1” Hex Head Grade 2 1
7 F05011-52 Washer, 9/16” SAE Flat 1
8 S13016 Nut, Pivot Rail Adjustment 1
9 F05005-42 Screw, 1/4-28 x 1/4” Brass Tip Set 2
10 P04107 Fitting, 3/16” Grease 1
11 F05007-114 BOLT, 3/8-16 X 4 3/4” CARRIAGE HEAD 2
12 F05007-113 BOLT, 3/8-16 X 5” CARRIAGE HEAD 6
13 F05011-3 WASHER, 3/8” SAE FLAT 8
14 F05010-10 NUT, 3/8-16 NYLON LOCK 8
017710 COVER KIT, PIVOT RAIL STAINLESS STEEL 2
(LT40)
015926 COVER KIT, PIVOT RAIL STAINLESS STEEL 2
(LT30)
15 S13012 Cover, Stainless Steel Pivot Bed Rail (LT40) 1
012994 Cover, Stainless Steel Pivot Bed Rail (LT30) 1
16 F05006-10 Bolt, 5/16-18 X 2 1/2" Hex Head 2
17 F05010-6 Nut, 5/16-18 Hex Lock 2
015970 WRENCH, BED RAIL ADJUSTMENT (See Section 8.1) 1

Bed Frame Assembly WM doc 11/23/22 8-7

 Bed Frame Assembly
8 Log Side Support Assembly (Manual)

8.7 Log Side Support Assembly (Manual)

(See Section 9.6) for optional hydraulic side supports

18
1 17
15
15
15 14
14

22
15

21
19
21
18

16 20 2
5 6
2
7
5

10 9
11
SM0271-6B 13 12
9

REF PART # DESCRIPTION COMMENTS QTY.

1 015235 SUPPORT, LOG SIDE 4
2 P04107 Fitting, 3/16" Grease 2
016559 MOUNTING KIT, LOG SIDE SUPPORT 4
3 016544 Pin, Log Side Support Pivot 1
4 F05005-4 Bolt, 1/4-20 X 1 1/2" Hex Head Grade 5 1
5 F05011-11 Washer, 1/4" SAE Flat 2
6 F05010-9 Nut, 1/4-20 Self Locking 1
7 016555 Plate, Log Side Support End 1
8 F05008-61 Bolt, 1/2-13 X 3 1/2" Hex Head Grade 5 2
9 F05011-2 Washer, 1/2" SAE Flat 5
10 F05010-8 Nut, 1/2-13 Hex Nylon Lock 3
11 014632 Washer, .52” x 1.69” 1
12 F05008-33 Bolt, 1/2-13 X 1 1/2" Hex Head Grade 5 1
13 016558 Plate, Side Support Washer Clamp 1
016562 ROLLER KIT, SIDE SUPPORT 4
14 016561 Roller, Side Support 2

8-8 WM doc 11/23/22 Bed Frame Assembly

 Bed Frame Assembly
Log Side Support Assembly (Manual) 8
REF PART # DESCRIPTION COMMENTS QTY.
15 F05011-5 Washer, 5/8” SAE Flat Additional 5/8" SAE Flat Washer 6
F05011-5 may be required on
each side of side support to pro-
vide clearance for optional
stainless steel side support
guards. Extra washers are
included in the stainless steel
guard retrofit kit (016798).
16 F05009-118 Bolt, 5/8-11 x 3 3/4” Hex Head Grade 5 1
17 F05010-96 Nut, 5/8-11 Hex Nylon Lock Jam 1
18 016560 Bushing, Bronze 5/8” x 1” x 3/4” 2
F05008-94 Bolt, 1/2-13 x 3 1/2” Carriage Head 1
016562-526 Instruction Sheet, Side Support Roller 1
016798 GUARD KIT, STAINLESS STEEL SIDE SUPPORT 1
(OPTIONAL)
19 016722 Guard, Stainless Steel Side Support 4
20 F05005-4 Bolt, 1/4-20 x 1 3/4” Hex Head 8
21 F05011-11 Washer, 1/4” SAE Flat 16
F05011-5 Washer, 5/8” SAE Flat Additional 5/8" SAE Flat Washer 4
F05011-5 may be required on
each side of side support to pro-
vide clearance for optional
stainless steel side support
guards. Extra washers are
included in the stainless steel
guard retrofit kit (016798).
22 F05010-69 Nut, 1/4-20 Hex Nylon Lock 8
016798-1005 Instruction Sheet, Stainless Steel Side Support 1
Guard Retro

Bed Frame Assembly WM doc 11/23/22 8-9

 Bed Frame Assembly
8 Safety Chain Assembly

8.8 Safety Chain Assembly

4
2

3
1

SM0129B

REF PART # DESCRIPTION COMMENTS QTY.

1 107972 CHAIN, 15 INCH SAFETY 1
2 F05008-33 BOLT, 1/2-13X1 1/2 HEX HEAD GRADE 5 1
3 F05010-8 NUT, 1/2-13 NYLON HEX LOCK 1
4 F05011-35 WASHER, 7/16 STANDARD FLAT 1

8-10 WM doc 11/23/22 Bed Frame Assembly

 Bed Frame Assembly
Saw Head Rest Pin Assembly 8
8.9 Saw Head Rest Pin Assembly

REF PART # DESCRIPTION COMMENTS QTY.

079485 Pin Assy, Rest, 40/50
079511 Pin Assy, Rest, 40/50 Hyd Wide
1 014102 Pin Weldment, C-Frame Rest 96 Hyd 1
079510 Pin Wldmt, Rest, 40/50 Hyd Wide 1
2 014151 Pin, 3/8x2 1/4 Sq Wire Lock 1
3 F05008-74 Bolt, 1/2-13 x 2 1/2” Hex Head Grade 5 F05008-74 was F05008-10; two 1
washers added after 5/14/2021,
ECN 37840.
4 F05011-2 Washer, 1/2 SAE Flat 4
5 F05010-3 Nut, 1/2-13 Swaged Hex 1

Bed Frame Assembly WM doc 11/23/22 8-11

 Bed Frame Assembly
8 Rest Pin Assembly

8.10 Rest Pin Assembly

REF PART # DESCRIPTION COMMENTS QTY.

079096 Pin Assy, Rest, Manual ECN:21293 1
1 074980 Pin Wldmt, C-Frame Rest, Manual 1
2 f05010-25 Nut, 3/8-16 Swaged 2
3 f05011-3 Washer, 3/8 Flat SAE 2
4 f05007-206 BOLT, 3/8-16X2 3/4 HH Gr5 2
5 f05010-3 NUT, 1/2-13 SWAGED HEX 1
6 f05011-2 Washer, 1/2 SAE Flat 2
7 110557 Bracket, Rest Pin Mount 1
8 014151 Pin, 3/8x2 1/4 SQ Wire Lock 1
9 f05008-10 Bolt, 1/2-13x2 1/4 Hex Head GR5 1

8-12 WM doc 11/23/22 Bed Frame Assembly

 Bed Frame Assembly
Bed Frame Decals 8
8.11 Bed Frame Decals

7 7

4 5 2
Po ten tial P inch
Po in t W hen Ca rria ge
Is Retu r ning

KEEP AL L PERSONS
A SAF E DI STANCE AWAY
WHIL E OPERATI NG
THIS M ACH INE 0985
S 1

1 2 3 4 230022

REF PART # DESCRIPTION COMMENTS QTY.

1 S12281 DECAL, WOOD-MIZER LOGO 1
1 014751 DECAL, WOOD-MIZER SUPER LOGO 1
2 P07453 DECAL, AMBER REFLECTIVE 2” ROUND 2
3 S09851 DECAL, KEEP AWAY DANGER 1
4 P07452 DECAL, RED REFLECTIVE 2” ROUND 3
5 P10287 DECAL, PINCH POINT DANGER 1
6 S12581 DECAL, SAW HEAD REST CAUTION 1
7 S12051 DECAL, LOG LIMIT STRIPE 2

Bed Frame Assembly WM doc 11/23/22 8-13

 Bed Frame Assembly
8 Log Clamp

8.12 Log Clamp

8
9

7
1
10

11

6
5

2
4
3 230004B
REF PART # DESCRIPTION COMMENTS QTY.
1 W09412 CLAMP, LOG 1
2 M04311 CHAIN, LOG CLAMP 1
3 F05007-2 BOLT, 3/8-16 X 1 1/4" HEX HEAD GRADE 2 1
4 F05011-3 WASHER, 3/8" STANDARD FLAT 2
5 F05010-10 NUT, 3/8-16 HEX NYLON LOCK 1
6 P09136 SPRING, LOG CLAMP CHAIN 1
7 W09404 PLATE, LOG CLAMP STOP 1
8 F05008-33 BOLT, 1/2-13 X 1 1/2" HEX HEAD GRADE 5 2
9 F05011-2 WASHER, 1/2" SAE FLAT 2
10 F05010-8 NUT, 1/2-13 HEX NYLON LOCK 2
11 W09310 CHANNEL WELDMENT, MANUAL LOG CLAMP 1

8-14 WM doc 11/23/22 Bed Frame Assembly

 Bed Frame Assembly
Log Loading Ramps 8
8.13 Log Loading Ramps

REF PART # DESCRIPTION COMMENTS QTY.

K09466 RAMP KIT, LOG LOADING WITH RETAINERS 1
1 W09014 Ramp, Log Loading 2
K09810 Retainer Kit, Log Ramp 2
2 W09413 Retainer, Log Ramp Available in assemblies only. 1
3 P09335 Spring, Log Ram Retainer 1
4 F05011-19 Washer, 5/8" I.D. x .100" Thick Nylon 1
5 F05012-11 Pin, 3/16" x 1" Roll 1

Bed Frame Assembly WM doc 11/23/22 8-15

 Bed Frame Assembly
8 Board Return Table Assembly (Optional)

8.14 Board Return Table Assembly (Optional)

SM0330
11
STOP!
Never use the board
return table as a
platform to stand on.

Serious injury may

result.
Wood-Miz er Products, Inc .
800-525-8100 Reorder #016077

4
To Avoid Injury:

12 Keep all persons out of

the path of returning
boards.

Failure to do so will
result in serious injury.
Wood-M izer Products, Inc.
800- 525-8100 Reorder 015365

2 4
9
8
10
1

5
6 7
8
10
5
6
9

3 9
8

REF PART # DESCRIPTION COMMENTS QTY.

003264 TABLE ASSEMBLY, BOARD RETURN (LT40) 1
003270 TABLE ASSEMBLY, BOARD RETURN (LT30) 1
1 055515 Table Weldment, Board Return 1
2 003259 Cover, Board Return Table 1
3 055533 Mount Weldment, Board Return Table (LT40) 1
038992 Mount Weldment, Board Return Table (LT30) 1
4 F05006-9 Bolt, 5/16-18 x 1” Carriage Head 8
5 F05011-17 Washer, 5/16” SAE Flat 8
6 F05010-58 Nut, 5/16-18 Nylon Lock 8
7 003207 Bolt, 3/8-16 x 4” x 5” ‘U’ 2
8 F05011-3 Washer, 3/8” SAE Flat 10
9 F05010-10 Nut, 3/8-16 Hex Nylon Lock 7
10 F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 3
11 016077 Decal, Board Return Table Warning 1
12 015365 Decal, Board Return Danger 1

8-16 WM doc 11/23/22 Bed Frame Assembly

 Bed Frame Assembly
Board Outfeed Table (Optional) 8
8.15 Board Outfeed Table (Optional)

9 10

2
7 8
1

6 10

3
9
7
8
5
6

3
4 5

SM0316 4

REF PART # DESCRIPTION COMMENTS QTY.

016652 TABLE ASSEMBLY, BOARD OUTFEED 1
1 016606 Table Weldment, Board Outfeed 1
2 038167 Roller, 2 1/2” x 25” 6
3 016609 Mount Weldment, Outfeed Table Leg 2
4 016651 Leg Weldment, Outfeed Table 4
5 014151 Pin, 3/8” x 2 1/4” Square Wire Lock 4
6 016677 Pin, Snap - Coil Tension 4
7 F05007-135 Bolt, 3/8-16 x 3 1/4” Hex Head 4
8 F05010-10 Nut, 3/8-16 Hex Nylon Lock 4
9 S12641 Decal, Hand Pinch Point Warning 4
10 016991 Decal, 1 1/2” Wood-Mizer Logo 2

Bed Frame Assembly WM doc 11/23/22 8-17

 Bed Frame Assembly
8 Manual Winch

8.16 Manual Winch

REF PART # DESCRIPTION COMMENTS QTY.

MW-A MANUAL WINCH ASSEMBLY 1
1 P12323 Winch, Manual 3500lb Available in assemblies only. 1
2 P04487 Handle, Manual Winch 1
3 P05087 Cable, Manual Winch 7/32" Dia. X 50' Long 1
4 S12321 Bracket, Winch Mount 1
5 F05007-11 Bolt, 3/8-16 X 1 1/4" Carriage 5
6 F05011-3 Washer, 3/8" Flat 1
7 F05010-10 Nut, 3/8-16 Hex Lock 5
8 S09393 Pulley, Winch Cable Guide 1
9 W09429 Bracket, Winch Cable Guide Pulley 1
10 F05012-24 Pin, 1/2" X 1 27/64" Clevis 1
11 F05011-2 Washer, 1/2" Sae Flat 1
12 F05012-1 Pin, 1/8" X 1" Cotter 1
13 F05009-8 Bolt, 5/8-11 X 4" Hex Head Full Thread 1
14 F05010-34 Nut, 5/8-11 Nylon Lock 1

8-18 WM doc 11/23/22 Bed Frame Assembly

 Bed Hydraulic System
Hydraulic Hoses 9
SECTION 9 BED HYDRAULIC LOG LOADER & TURNER (OPTIONAL)
9.1 Hydraulic Hoses

“A” HD0017

LENGTH DESCRIPTION (NOTE: See Hydraulic Information Section in Opera-

COLOR "A" tor’s Manual for Hydraulic Schematics) PART # QTY.
Green 62" LOADING ARM BRANCH TOP 079000-62 2
Yellow 64" LOADING ARM BRANCH BASE 079000-64 2
Blue 148" LOADING ARM TOP 079000-148 1
Red 158" LOADING ARM BOTTOM 079000-158 1
Plain 27” LOG TURNER BASE 079000-27 1
Orange 18” LOG TURNER TOP 079000-18 1
Plain 220” SIDE SUPPORT TOP 079000-220 1
Pink 206” SIDE SUPPORT BASE 079000-206 1

Bed Hydraulic System WM doc 11/23/22 9-1

 Bed Hydraulic System
9 Hydraulic Loader/Turner Control Box

9.2 Hydraulic Loader/Turner Control Box

18
14 13
12
8 3 16
7
19
15
32
9
14
10 15 2
11
27 28

6
30 31 4 22
5
29
23 16

20
24 16
24 16 18
1
21
26 25

16 300154
17

18

REF PART # DESCRIPTION COMMENTS QTY.

025717 BOX ASSEMBLY, HYDRAULIC DUAL FUNCTION 1
CONTROL
1 025716 Box Weldment, Hydraulic Dual Function Con- 1
trol
2 025714 Cover Weldment, Hydraulic Dual Function 1
Control
3 025713 Pump/Valve Assembly, Hydraulic Dual Func- 1
tion #M-500 4W/4W
4 Pump, Hydraulic Replacement Monarch 1
Model #12171-250
052807 Motor Kit, Hydraulic Replacement 1
5 038683 Motor, 12 VDC Hydraulic Pump Available in assemblies only. 1
#08714 (Iskra)
038682 Brush Kit, 4-Valve Hydraulic 1
Pump Motor #08658-I (Iskra)
P12513 Bearing, Base Motor #02318 1
6 052806 Wire Assembly, Motor Brush 1
Ground
7 P09596 Cap, Hydraulic Pump Vented Fill #01143 1
8 Valve Assembly, 4-Way Monarch #19760 2
9 025818 Spring, Hydraulic Pump Valve Con- 4
tact #00015
10 Handle Assembly, Hydraulic Pump 2
Valve #

9-2 WM doc 11/23/22 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Loader/Turner Control Box 9
REF PART # DESCRIPTION COMMENTS QTY.
P09753 Spring, Hydraulic Pump Valve Han- 2
dle #00018
11 Solenoid, 12 VDC Motor Starter #17744 1
12 P05389 Fitting, 1/4” NPT Hex Nipple 2
13 P03420 Fitting, 1/4” NPT Coupling 2
14 P09142 Fitting, 1/4” NPT x 1/4” JIC Male Elbow 4
15 016815 Fitting, 1/4” JIC Cap 4
16 F05011-3 Washer, 3/8” SAE Flat 10
17 F05011-4 Washer, 3/8” Split Lock 4
18 F05007-87 Bolt, 3/8-16 X 1" Hex Head Grade 5 8
19 P12961 Decal, Keep Away Hydraulic Warning 1
20 036720 Decal, Hydraulic Logo 1
21 043405 Grommet, 1 1/2” x 3/16” 1
22 P26258 Fitting, 1/2” NPT Plug 1
23 F05007-78 Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 1
24 F05011-36 Washer, 3/8" External Star Lock 2
25 F05010-10 Nut, 3/8-16 Hex Nylon Lock 1
26 F05010-29 Nut, 3/8-16 Hex Jam 1
27 F05006-5 Bolt, 5/16-18 x 3/4” Hex Head 1
28 F05011-33 Washer, 5/16” External Star Lock 1
29 S12825 Decal, Hydraulic Fluid 1
30 F05010-200 Nut, M6-1.0 Hex Nylon Lock 1
31 F05011-37 Washer, 1/4” Exterior Star Lock 1
32 Cable Assembly, 10” Pump To Solenoid 1
P12742 FLUID, 1-QUART DEXRON III HYDRAULIC 4
006397 FLUID, 1-GALLON CONOCO MV32 1
P12822 FLUID, 1-GALLON EXXON UNIVIS HVI 13 1
HYDRAULIC

Bed Hydraulic System WM doc 11/23/22 9-3

 Bed Hydraulic System
9 Hydraulic Power Supply Strip

9.3 Hydraulic Power Supply Strip

23
24 25 28 29 26 30
11 1
4
2
5
27
3
15
8

17
10 18
12 6 7 9
21

20
22

13 16

HD0176-1C 14
19

REF PART # DESCRIPTION COMMENTS QTY.

010103 CONTACT ASSEMBLY, HYDRAULIC POWER 1
SUPPLY (POSITIVE)
007716 CONTACT KIT, 97+ HYDRAULIC POWER 1
SUPPLY POSITIVE
1 015253 Contact, Hydraulic Power Supply (Posi- Available in assemblies only. 1
tive)
2 P10077 Spring, Positive Contact 2
3 F05006-143 Bolt, 5/16" X 3/4" Shoulder (1/4-20 2
Thread) Stainless
4 F05006-20 Bolt, 5/16-18 x 1/2” Socket Button Head 1
5 S10072 Insulator, Positive Contact 1
6 015324 Bracket, Positive Contact Mounting 1
7 F05011-11 Washer, 1/4" SAE Flat 2
8 128088 Cable Assy, 1AWG Red x13 (2x5/16 Term) Cable assemblies replaced
R01971 and F05092-16 after
9/17/2019 per ECN 37793
R01971 Cable, #1 Weld Available in assemblies only. Ft
F05092-16 Terminal, 5/16" Ring #2 Gauge 2
9 F05005-38 Bolt, 1/4-20 X 1" Hex Head Grade 2 2
10 F05010-9 Nut, 1/4-20 Hex Self-Locking 2
11 F05007-11 Bolt, 3/8-16 X 1 1/4” Carriage Head 2
12 F05010-10 Nut, 3/8-16 Hex Nylon Lock 2
010104 CONTACT KIT, HYDRAULIC POWER SUPPLY 1
(GROUND)
13 F05011-3 Washer, 3/8" SAE Flat 2

9-4 WM doc 11/23/22 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Power Supply Strip 9
REF PART # DESCRIPTION COMMENTS QTY.
14 F05010-10 Nut, 3/8-16 Hex Nylon Lock 2
15 F05007-175 Bolt, 3/8-16 X 4" Square Head 2
16 016792 Bracket, Ground Contact Mounting 1
17 017673 Cable Assy, 1AWG Blk x26-1/2 Cable assemblies replaced 1
R01971 and F05092-16 after
9/17/2019 per ECN 37793
R01971 Cable, #1 Weld Available in assemblies only. 2.2 Ft
F05092-16 Terminal, 5/16” Ring #2 Gauge 2
007717 Contact Kit, Hydraulic Power Supply Ground 1
18 015264 Contact, Hydraulic Power Supply Available in assemblies only. 1
(Ground)
19 F05006-93 Bolt, 5/16-18 X 1 1/4" Hex Head Full 2
Thread Grade 5
20 P10077 Spring, Ground Contact 2
21 F05010-17 Nut, 5/16-18 Hex 2
22 F05011-17 Washer, 5/16" SAE Flat 2
A11977 STRIP ASSEMBLY, 6' HYDRAULIC POWER SUP- 1
PLY W/3 FT. CABLE
23 F05015-1 Screw, 1/4-20 X 1/2" Slotted Hex Head 8
24 P11976 Housing, 6' Contact Strip 1
A12043-N Strip, 6' Contact With Cable 1
25 S10075 Strip, 6' Contact Available in assemblies only. 1
26 052161 Cable Assy, 1AWG Blk x36 (2x5/16 Term) Cable assemblies replaced 1
R01971 and F05092-16 after
9/17/2019 per ECN 37793
R01971 Cable, #1 Weld Available in assemblies only. 3 Ft
F05092-16 Terminal, 5/16" Ring #2 Gauge 2
27 F05006-45 Bolt, 5/16-18 X 3/4" Hex Head Black 1
Nylon
28 F05010-86 Nut, 5/16-18 Hex Black Nylon 1
29 R01950-8 Tube, 5/8" Heat Shrink w/Adhesive ID Available in assemblies only. Ft
30 P04137 Grommet, 5/8” Wire 1

Bed Hydraulic System WM doc 11/23/22 9-5

 9 Hydraulic Log Loader (Optional)

9.4 Hydraulic Log Loader (Optional)

18 23
15
19
20 21
9 10 14
16 11 4
24 13
17 18 12
14

22 6 5
18 23
3 6 10
19 9
8
21 14
24 4 2 11 7
11 13
12
18 14
1
22 9 6
10 5
6
8

7
9
300137-1B
10
11
3

REF PART # DESCRIPTION COMMENTS QTY.

LTHDLA-M LOADER KIT, HYDRAULIC LOG (MANUAL SAW- 1
MILL OPTION)
1 036722 Arm, Hydraulic Log Loading 1
2 P04107 Fitting, 3/16" Grease 2
3 W09444 Channel, Hydraulic Log Loading Foot 2
4 P04107 Fitting, 3/16" Grease 4
A09284 Cylinder Assembly, Hydraulic Log Loading Available in assemblies only. 2
Arm
5 P12847 Cylinder, 8" X 3" Hydraulic 1
P12956 Seal Kit, 8" x 3" Hydraulic Cylinder 1
6 P09143 Fitting, C5205x4x4 Male Connector 2
7 P12199 Fitting, 0455x4x4 90° Swivel Elbow 1
015832 Fitting Kit, 1/4NPT 5.0GPM Velocity Fuse 1
8 015750 Fitting, 1/4NPT 5.0GPM Velocity Available in assemblies only. 2
Fuse
015832-255 Instruction Sheet, Velocity Fuse 1
Replacement
9 W09446 Pin, Loading Arm Mount 4
10 F05005-1 Bolt, 1/4-20 x 3/4” Hex Head Full Thread 4
11 F05010-69 Nut, 1/4-20 Hex Lock 4
12 S09251 Pin, Loading Arm Cylinder Mount 2
13 F05011-28 Washer, 1" SAE Flat 4
14 F05012-23 Pin, 3/16" X 1 1/2" Cotter 4
15 P09145 Fitting, C5705x5x4 Union 'T' 2

9-6 WM doc 11/23/22

 Hydraulic Log Loader (Optional) 9
REF PART # DESCRIPTION COMMENTS QTY.
16 S09245 Clamp, 1/4” Hydraulic Hose
17 F05006-102 Bolt, 5/16-18 X 3/4" Hex Head Grade 5
18 F05008-116 BOLT, 1/2-13 X 2” HEX HEAD FULL THREAD
GRADE 5
19 F05010-31 NUT, 1/2-13 JAM 2
20 036715 FITTING, 1/4” JIC X 1/4” JIC ELBOW 2
21 048270 MOUNT WELDMENT, LOADER ARM 2
22 036737 PLATE WELDMENT, LOADER ARM MOUNT 2
23 038472 PIN ASSEMBLY, 3/8" X 3" WIRE LOCK 2
24 F05010-8 NUT, 1/2-13 HEX NYLON LOCK 8

WM doc 11/23/22 9-7

 Bed Hydraulic System
9 Hydraulic Log Turner (Optional)

9.5 Hydraulic Log Turner (Optional)

20

10 2
23
21 21
22

9
8 26
15
8
9 4 7
25
24 24 26
1 6
4
25 5

17 7 19
14 6 6
3 12 13
300155-2

16 6
11 18
13 6 5
19
17 12

REF PART # DESCRIPTION COMMENTS QTY.

007069 ARM ASSEMBLY, MANUAL MILL HYDRAULIC 1
TURNER
1 015231 Arm, Hydraulic Log Turner Link 1
2 P04107 Fitting, 3/16” Grease 2
3 015233 Arm, Hydraulic Log Turner Painted 1
4 014675 Claw, Hydraulic Log Turner 2
5 F05008-28 Bolt, 1/2-13 X 5 1/2" Hex Head Grade 5 4
6 F05011-2 Washer, 1/2” SAE Flat 16
7 F05010-8 Nut, 1/2-13 Hex Nylon Lock 8
8 015085 Pin, Log Turner Mount 2
9 F05006-1 Bolt, 5/16-18 X 1" Hex Head Grade 2 2
10 F05010-58 Nut, 5/16-18 Hex Nylon Lock 2
11 S09246 Pin, Log Turner Pivot 1
12 F05011-28 Washer, 1" SAE Flat 2
13 F05012-23 Pin, 3/16" X 1 1/2" Cotter 2
14 015718 Spring, Hydraulic Log Turner 2
15 006999 Mount Weldment, Manual Mill Hydraulic Log 1
Turner
A09286 Cylinder Assembly, Hydraulic Log Turner 1
16 P12846 Cylinder, 8" X 2 1/2" Hydraulic Available in assemblies only. 1
P12955 Seal Kit, 8" x 2 1/2" Hydraulic Cylin- 1
der

9-8 WM doc 11/23/22 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Log Turner (Optional) 9
REF PART # DESCRIPTION COMMENTS QTY.
17 P09142 Fitting, 1/4” NPT x 1/4” JIC 90° Male 2
Elbow
18 007048 Plate, Manual Mill Hydraulic Log Turner Mount 1
19 F05008-33 Bolt, 1/2-13 x 1 1/2” Hex Head Grade 5 4
20 F05007-113 Bolt, 3/8-16 x 5” Carriage Head 2
21 F05011-3 Washer, 3/8” SAE Flat 6
22 F05010-10 Nut, 3/8-16 Hex Nylon Lock 4
23 F05007-5 Bolt, 3/8-16 x 5” Hex Head 2
24 S09245 Plate, 1/4” Hose Clamp 2
25 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 2
26 F05010-20 Nut, 5/16-18 Hex Self-Locking 2

Bed Hydraulic System WM doc 11/23/22 9-9

 Bed Hydraulic System
9 Hydraulic Log Side Supports (Optional)

9.6 Hydraulic Log Side Supports (Optional)

20 19
23
20 19
23
21

22
25
26

1 27
300155-1
24

18 2
17

16
12
13
3
14
18 5

6 11
17 15
5
8
16
9
7
4
10 8
6
9
7
4

REF PART # DESCRIPTION COMMENTS QTY.

1 W12339 SUPPORT, HYDRAULIC LOG SIDE 2
2 P04107 Fitting, 3/16” Straight Grease 2
A09283 CYLINDER ASSEMBLY, HYDRAULIC LOG SIDE 1
SUPPORT
3 P12845 Cylinder, 6" X 2" Hydraulic 1
P12954 Seal Kit, 6" x 2" Hydraulic Cylinder 1
4 P09142 Fitting, 1/4” NPT x 1/4” JIC 90° Male Elbow 2
5 P09140 Fitting, 1/4” NPT 90° Male Elbow 2
6 P09141 Fitting, 1/4” NPT x 1/4” JIC Male Run 'T' 2
7 P09143 Fitting, 1/4” NPT x 1/4” JIC Male Connector 2
8 015484 Valve, Hydraulic Sequence 2
9 015490 Fitting, 3/8” NPT - 1/4” NPT Reducer 4
10 015026 ROD, HYDRAULIC SIDE SUPPORT LINK 1
11 P09137 END, 1/2" ROD 2
12 F05008-10 BOLT, 1/2-13 X 2 1/4" HEX HEAD GRADE 5 2
13 F05011-2 WASHER, 1/2" SAE FLAT 4
14 F05010-8 NUT, 1/2-13 HEX NYLON LOCK 2
15 F05010-16 NUT, 1/2-20 HEX JAM 1

9-10 WM doc 11/23/22 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Log Side Supports (Optional) 9
REF PART # DESCRIPTION COMMENTS QTY.
16 S09251 PIN, CYLINDER MOUNT 2
17 F05011-28 WASHER, 1" SAE FLAT 4
18 F05012-23 PIN, 3/16" X 1 1/2" COTTER 4
016562 ROLLER KIT, SIDE SUPPORT (OPTIONAL) 2
19 016561 Roller, Side Support 2
20 F05011-5 Washer, 5/8” SAE Flat Additional 5/8" SAE Flat Washer 6
F05011-5 may be required on
each side of side support to pro-
vide clearance for optional
stainless steel side support
guards. Extra washers are
included in the stainless steel
guard retrofit kit (016798).
21 F05009-118 Bolt, 5/8-11 x 3 3/4” Hex Head Grade 5 1
22 F05010-96 Nut, 5/8-11 Hex Nylon Lock Jam 1
23 016560 Bushing, Bronze 5/8” x 1” x 3/4” 2
F05008-94 Bolt, 1/2-13 x 3 1/2” Carriage Head 1
016562-526 Instruction Sheet, Side Support Roller 1
016798 GUARD KIT, STAINLESS STEEL SIDE SUPPORT 1
(OPTIONAL)
24 016722 Guard, Stainless Steel Side Support 4
25 F05005-4 Bolt, 1/4-20 x 1 3/4” Hex Head 8
26 F05011-11 Washer, 1/4” SAE Flat 16
F05011-5 Washer, 5/8” SAE Flat Additional 5/8" SAE Flat Washer 4
F05011-5 may be required on
each side of side support to pro-
vide clearance for optional
stainless steel side support
guards. Extra washers are
included in the stainless steel
guard retrofit kit (016798).
27 F05010-69 Nut, 1/4-20 Hex Nylon Lock 8
016798-1005 Instruction Sheet, Stainless Steel Side Support 1
Guard Retro

Bed Hydraulic System WM doc 11/23/22 9-11

 Hydraulic Log Loader & Turner (Optional)
9 Miscellaneous Loader & Turner Parts

9.7 Miscellaneous Loader & Turner Parts

22
10 14 24
12 300153B
13 11 6
2
7 19
6 18
17 15 2
16
23
27 1
5
3
21
4
1
3 4
3
28

2
8
9
29 30
20

25

26

REF PART # DESCRIPTION COMMENTS QTY.

1 048269 PLATE, AXLE MOUNT 2
2 F05008-33 BOLT, 1/2-13 X 1 1/2" HEX HEAD GRADE 5 3
3 F05011-2 WASHER, 1/2" SAE FLAT 4
4 F05010-8 NUT, 1/2" HEX NYLON LOCK 3
5 P11550 FUSE, 225A 12V 2
6 F05011-11 WASHER, 1/4" SAE FLAT 4
7 F05010-21 NUT, 1/4-20 HEX LOCK 2
8 048426 BRACKET, WINCH MOUNT 1
9 P12960 DECAL, HYDRAULIC CONTACT CAUTION 1
10 053339 FUSE, 225A 32V MEGA 2
11 056998 BLOCK, 3/4" LOWER FUSE 1
12 F05005-59 SCREW, 1/4-20 X 1/2" SOCKET BUTTON HEAD 1
13 F05011-14 WASHER, 1/4" SPLIT LOCK 1
14 F05005-123 BOLT, 1/4-20 X 3/4" HEX HEAD GRADE 5 1
15 F05006-20 SCREW, 5/16-18 X 1/2" SOCKET BUTTON HEAD 1
16 F05011-13 WASHER, 5/16" SPLIT LOCK 2
17 F05006-102 BOLT, 5/16-18 X 3/4" HEX HEAD GRADE 5 2
18 055323 SPACER, .39" X .625" X .39" 2
19 F05006-2 BOLT, 5/16-18 X 1 1/2" HEX HEAD FULL 2
THREAD
20 006867 DECAL, 150A/225A MEGA FUSE ID 1
21 P11764 GROMMET, 5/8" ID RUBBER 2
22 016371 SOLENOID KIT, 200A 12V SPST CONT. DUTY 1
015470 Solenoid, 200A 12V SPST Cont. Duty Available in assemblies only. 1
015426 Diode Assembly, Solenoid Coil Chassis Gnd 1

9-12 WM doc 11/23/22 Hydraulic Log Loader & Turner (Optional)

 Hydraulic Log Loader & Turner (Optional)
Miscellaneous Loader & Turner Parts 9
REF PART # DESCRIPTION COMMENTS QTY.
024451 WIRE ASSEMBLY, HYDRAULIC SOLENOID 1
VOLTAGE DROP
23 F05005-15 BOLT, 1/4-20 X 1/2” HEX HEAD 2
24 F05010-9 NUT, 1/4-20 SELF-LOCKING HEX 2
25 036305 CABLE ASSEMBLY, 1 GA X 6 1/2” FUSE TO 1
SOLENOID
26 036307 CABLE ASSEMBLY, 1 GA X 14” SOLENOID TO 1
POSITIVE CONTACT
27 F05008-128 BOLT, 1/2-13 X 1" HEX HEAD GRADE 8 1
28 F05010-127 NUT, 1/2-13 HEX NYLON HALF NUT 1
29 025745 PLATE, HLT TRAVEL 1
30 P11809 DECAL, BEFORE TOWING CAUTION 1

Hydraulic Log Loader & Turner (Optional) WM doc 11/23/22 9-13

 Miscellaneous
10 Replacement Manuals

SECTION 10 MISCELLANEOUS
10.1 Replacement Manuals

300147-6

REF DESCRIPTION ( Indicates Parts Available In Assemblies Only) PART # QTY.

Wood-Mizer Product Information
1 ALL-PRODUCTS CATALOG PS750 1
Basic Sawmill Manuals
2 TRU-SHARP BLADE HANDBOOK M600 1
3 WOOD-MIZER GENERAL INFORMATION M601 1
4 LT30/LT40 OPERATOR’S MANUAL M1645 1
5 LT30/LT40 PARTS MANUAL M1644 1
Power Option Manuals
6 G28 ENGINE OPTION MANUAL M1159 1
7 KOHLER CH20/CH25 OWNER’S MANUAL 015993 1
8 KOHLER CH20/CH25 SERVICE MANUAL 015994 1
9 D35 ENGINE OPTION MANUAL M1573 1
10 D36 ENGINE OPTION MANUAL M1598 1
Trailer Option Manuals
11 STANDARD TRAILER OPTION M793 1
Miscellaneous Option Manuals
12 MANUAL WINCH OPTION MANUAL M619-23 1
13 LOG TURNER OPTION MANUAL M620 1
14 MANUAL TOE BOARD OPTION MANUAL M627 1
15 SHINGLE/LAPSIDER OPTION MANUAL M621 1
16 OPERATOR’S SEAT OPTION MANUAL M613 1
17 RESAW ATTACHMENT OPTION MANUAL M263 1
18 BED EXTENSION OPTION MANUAL M294 1
19 MKII DEBARKER ATTACHMENT OPTION MANUAL M546 1
20 ACCUSET 2 OPTION MANUAL M1517 1
21 SIMPLE SET OPTION MANUAL M1611 1
22 LASER SIGHT OPTION MANUAL M679 1
23 AUTOCLUTCH OPTION MANUAL M883 1
24 LUBE-MIZER OPTION MANUAL M885 1
25 LATHE-MIZER OPTION MANUAL M1337 1
Electrical Diagrams
26 G28 ELECTRICAL INFORMATION M1154 1
27 D35 ELECTRICAL INFORMATION M1574 1
28 D36 ELECTRICAL INFORMATION M1595 1

10-1 WM doc 11/23/22 Miscellaneous

 INDEX

B D

battery box 5-10 debarker wire box/hole plugs 4-15

bed rails decals

front/rear 8-1 frame 8-13
middle front 8-3 saw head 4-10
middle rear 8-4
pivot 8-7
F
blade guide arm 2-9
drive 2-7 feed chain 7-4

blade guides
drive side 2-4 H
idle side 2-1
throat screw 4-1 hydraulic
control box 9-2
blade wheels hoses 9-1
drive side 3-1, 3-3 loader/turner misc. 9-12
idle side 3-5 power strip 9-4

board return 4-16

L
board return table 8-16
legs
brake assembly 4-6
stationary 8-5

log clamp 8-14

C
log loading ramps 8-15
clutch lever 4-3

clutch mount 4-5

M
control box 5-1, 5-3
manuals 10-1
circuit breakers 5-6
drum switches 5-5
front panel & harnesses 5-7, 5-9
O
covers
blade housing 4-11 outfeed table option 8-17
drive belt 4-13

power feed 7-2

Index 30doc112322 i
R

rest pin 8-11, 8-12

sawdust chute 4-14

side supports 8-8

tensor de hoja 3-6

track rollers
lower 7-5
upper 7-1

up/down
blade scales 6-2
chain & sprockets 6-4
drive 6-5
saw head mount 6-1

water lube
bottle/tray 4-7, 4-8
valve 4-2

winch 8-18

ii 30doc112322 Index