Wood-Mizer® Sawmill

Parts Manual

LT50HD rev. A6.01

Safety is our #1 concern!

April 2023
Form #1299

WARNING! Read and understand this

! manual before using this machine.
 California
Proposition 65 Warning

WARNING: Breathing gas/diesel engine exhaust exposes you to chemicals known to

the State of California to cause cancer and birth defects or other reproductive harm.

Always start and operate the engine in a well-ventilated area.

If in an enclosed area, vent the exhaust to the outside.
Do not modify or tamper with the exhaust system.
Do not idle the engine except as necessary.

For more information go to www.P65warnings.ca.gov.

WARNING: Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the State of California to cause cancer. Avoid inhaling
wood dust or use a dust mask or other safeguards for personal protection.

For more information go to www.P65Warnings.ca.gov/wood.

Active Patents assigned to Wood-Mizer, LLC

Wood-Mizer, LLC has received patents that protect our inventions which are a result of a dedication to
research, innovation, development, and design. Learn more at: woodmizer.com/patents

©2022 Wood-Mizer LLC

Printed in the United States of America, all rights reserved. No part of this manual may be reproduced in any form by any
photographic, electronic, mechanical or other means or used in any information storage and retrieval system without
written permission from

Wood-Mizer, LLC
8180 West 10th Street
Indianapolis, Indiana 46214
Table of Contents Section-Page
SECTION 1 REPLACEMENT PARTS
1.1 How To Use The Parts List.................................................................... 1-1
To Order Parts ......................................................................1-1
1.2 Sample Assembly................................................................................... 1-1

SECTION 2 BLADE GUIDE ROLLERS & ARM

2.1 Blade Guide Assembly, Idle Side .......................................................... 2-1
2.2 Blade Guide Assembly, Drive Side ....................................................... 2-4
2.3 Blade Guide Arm Drive Assembly ........................................................ 2-7
2.4 Blade Guide Arm ................................................................................... 2-9

SECTION 3 BLADE WHEELS & TENSIONER

3.1 Blade Drive Assembly ........................................................................... 3-1
3.2 Idle Blade Wheel Assembly................................................................... 3-3
3.3 Hydraulic Blade Tensioner Assembly ................................................... 3-4

SECTION 4 SAW HEAD FRAME

4.1 Middle Throat Screw ............................................................................. 4-1
4.2 Water Lube Solenoid Valve................................................................... 4-2
4.3 Clutch Pivot............................................................................................ 4-3
4.4 Clutch Mount Assembly ........................................................................ 4-4
4.5 Brake Assembly ..................................................................................... 4-5
4.6 Brake Assembly (DC Only)................................................................... 4-6
4.7 Board Return Assembly ......................................................................... 4-7
4.8 Water Lube Assembly (Gas Only)......................................................... 4-9
4.9 Water Lube Assembly (Diesel & Electric Only) ................................. 4-10
4.10 Saw Head Decals ................................................................................. 4-12
4.11 Blade Housing Covers ......................................................................... 4-13
4.12 Drive Belt Covers................................................................................. 4-15
4.13 Sawdust Chute...................................................................................... 4-16
4.14 Debarker Wire Box/Hole Plugs ........................................................... 4-17

SECTION 5 CONTROL & BATTERY BOXES

5.1 Control Assembly .................................................................................. 5-1
5.2 Control Assembly (Tier4 Only) ............................................................ 5-3
5.3 Drum Switches....................................................................................... 5-5
5.4 Circuit Breakers ..................................................................................... 5-6
5.5 Front Panel Assembly & Harnesses....................................................... 5-7
5.6 Front Panel Assembly & Harnesses (US Only) ..................................... 5-9
5.7 Battery Box Assembly ......................................................................... 5-10
5.8 Fuse Box Assembly ............................................................................. 5-12

SECTION 6 UP/DOWN SYSTEM

6.1 Saw Head Mount.................................................................................... 6-1
6.2 Blade Height & Quarter Scales.............................................................. 6-2
6.3 Up/Down Chain & Sprockets ................................................................ 6-4
6.4 Up/Down Motor Assembly.................................................................... 6-5
6.5 Up/Down Drive Assembly..................................................................... 6-6

Table of Contents WM doc 5/11/23 iii

Table of Contents Section-Page
SECTION 7 FEED SYSTEM & TRACK ROLLERS
7.1 Upper Track Rollers And Wipers...........................................................7-1
7.2 Power Feed Assembly ............................................................................7-2
7.3 Feed Chain/Stop .....................................................................................7-4
7.4 Lower Track Rollers...............................................................................7-5

SECTION 8 BED FRAME ASSEMBLY

8.1 Bed Rail Assembly, Front And Rear......................................................8-1
8.2 Bed Rail Assembly, Middle Front..........................................................8-3
8.3 Bed Rail Assembly, Middle Rear...........................................................8-4
8.4 Fine Adjustable Legs Overview ............................................................8-5
8.5 FAO Outrigger, Front .........................................................................8-6
8.6 FAO Outrigger, Loading Side ............................................................8-7
8.7 FAO Outrigger, Offset Leg ................................................................8-8
8.8 FAO Outrigger, Rear ..........................................................................8-9
8.9 Board Return Table Assembly .............................................................8-10
8.10 Pivot Bed Rail Assembly......................................................................8-11
8.11 Safety Chain Assembly ........................................................................8-12
8.12 Saw Head Rest Pin Assembly ..............................................................8-13
8.13 Bed Frame Decals.................................................................................8-14
8.14 Board Outfeed Table (Optional) ........................................................8-15

SECTION 9 BED HYDRAULIC SYSTEM

9.1 Hydraulic Hoses .....................................................................................9-1
9.2 Hydraulic Control Box ...........................................................................9-2
9.3 Hydraulic Power Supply Strip................................................................9-5
9.4 Hydraulic Log Loader ............................................................................9-7
9.5 Hydraulic Log Turner.............................................................................9-9
9.6 Hydraulic Log Side Supports (Front) ...................................................9-11
9.7 Hydraulic Log Side Supports (Rear) ....................................................9-13
9.8 Hydraulic Log Side Supports (Link) ....................................................9-15
9.9 Hydraulic Log Clamp ...........................................................................9-16
9.10 Hydraulic Toe Board ........................................................................9-18

SECTION 10 MISCELLANEOUS
10.1 Replacement Manuals ..........................................................................10-1

iv WM doc 5/11/23 Table of Contents

 Replacement Parts
How To Use The Parts List 1
SECTION 1 REPLACEMENT PARTS
1.1 How To Use The Parts List

 Use the table of contents to locate the assembly that contains the part you need.

 Go to the appropriate section and locate the part in the illustration.

 Use the number pointing to the part to locate the correct part number and description in the table.

 Parts shown indented under another part are included with that part.

To Order Parts

 From the continental US, call 1-800-525-8100 to order parts. Have your customer number, vehicle
identification number, and part numbers ready when you call.

 From other international locations, contact the Wood-Mizer distributor in your area for parts.

1.2 Sample Assembly

REF PART # DESCRIPTION COMMENTS QTY.

012345 SAMPLE ASSEMBLY, COMPLETE INCLUDES ITEMS 1-6 1
1 F02222-22 Sample Part 1
2 F03333-33 Sample Part 2
098765 Sample Subassembly Includes items 3-6 1
3 S04444-44 Subassembly Sample Part 1
4 K55555 Subassembly Sample Part 1
054321 Sample Sub-Subassembly Includes items 5-6 2
5 022222 Sub-Subassembly Sample Part 1
6 F10234-56 Sub-Subassembly Sample Part 1

The Sample Assembly, Complete, part number 012345 (top level assembly) includes two parts (F0222-22
and F0333-33) and the 098765 subassembly.

Subassembly 098765 contains two parts(S04444-44 and K55555) and two copies of sub-subassembly
054321.

Each sub-subassembly 054321 contains two parts (022222 and F10234-56).

Replacement Parts WM doc 5/11/23 1-1

 Blade Guide Rollers & Arm
2 Blade Guide Assembly, Idle Side

SECTION 2 BLADE GUIDE ROLLERS & ARM

2.1 Blade Guide Assembly, Idle Side

3 22

21 4
2
20
19
2 2 37
30 41 25
3 23
29 36
24 10 28
1 40 35 43
2 31 32
44
3 5 27
8 45
26
6
38
16 9 33
6 39 34
11
47 7 12 42
13 14 46
49
52 15
48
16
51 17
50

18
53
Optional Relube 54
3H0994E
Blade Guide Roller

REF PART # DESCRIPTION COMMENTS QTY.

003992 GUIDE ASSEMBLY, IDLE SIDE BLADE ROLLER 1
003920 Block Assembly, Idle Side Blade Guide Mount 1
1 003921 Block Weldment, Blade Guide Mount Available in assemblies only. 1
2 F05010-17 Nut, 5/16-18 Hex 4
3 F05006-88 Bolt, 5/16-18 x 1” Hex Head Stainless 3
Steel
4 F05006-122 Screw, 5/16-18 x 1” Socket Head Flat 1
Point Stainless Steel Set
5 003924 Shaft Weldment, Idle Side Guide 1
6 P30127 Fitting, 1/8” NPT Socket Pipe Plug 3
7 007734 Fitting, 1/16” NPT Socket Pipe Plug 2
8 006322 Bracket Weldment, Idle Side Water Lube 1
9 F05007-78 Bolt, 3/8-16x1 1/2 Hex Head Grade 5 1
10 F05010-10 Nut, 3/8-16 Hex Nylon Lock 1

2-1 WM doc 5/11/23 Blade Guide Rollers & Arm

 Blade Guide Rollers & Arm
Blade Guide Assembly, Idle Side 2
REF PART # DESCRIPTION COMMENTS QTY.
A04925 Roller Assembly, Blade Guide (standard for Use kit 006382 to convert rollers 1
use with 1 1/4” & 1 1/2” blades) and guide blocks for both blade
guides for 1 1/2" blades.
014299 Roller Assembly, Extended Blade Guide 1
Optional relube versions of each
(optional for use with 1 1/2” blades)
roller configuration also avail-
able.
K07079 Bearing Kit, Blade Guide Rebuild 1
11 P04252 Washer, 5/8" White Felt 1
12 F04254-1 Ring, 1 1/8" Interior Retaining 1
13 015975 Bearing, R8-2RS Blade Guide Available in assemblies only. 2
14 P06455 Washer, 5/8" Gray Felt 1
F05005-105 Screw, 1/4-28 x 1/4” Socket Head 1
Cup Point Set Black Oxide
057407-1507 Instruction Sheet, Blade Guide 1
Rebuild
15 S04250 Roller, Flanged Blade Guide (1 1/4” & 1 Available in assemblies only. 1
1/2” blade)
014298 Roller, Flanged Blade Guide (1 1/2” Available in assemblies only. 1
blade)
A04925-364 Instruction Sheet, Blade Guide Roller 1
Replacement
16 S04253 Spacer, Blade Guide 2
17 F05011-125 Washer, 1/2” Nord-Lock 1
18 F05008-10 Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 1
19 F05011-17 Washer, 5/16” SAE Flat 2
20 F05011-13 Washer, 5/16” Split Lock 2
21 F05006-76 Bolt, 5/16-18 x 1 1/2” Hex Head 2
22 035656 Bolt, Blade Guide Vertical Adjustment 1
23 F05010-17 Nut, 5/16-18 Hex 1
24 F05006-136 Bolt, 5/16-18 x 2 3/4” Hex Head Full Thread 1
006325 GUIDE KIT, HIGH-PERFORMANCE BLADE High-Performance Blade Guide 1
GUIDE (OPTIONAL) Kit requires LMS blade lube sys-
tem. If sawmill not already
equipped with LMS, add kit .
003928 Block Assembly, Idle Side Blade Guide 1
25 003915 Plate, Block Tilt Adjustment 1
26 003909 Block, Guide Block Mount 1
27 F05012-22 Pin, 3/16” x 5/8” Roll 2
28 F05011-3 Washer, 3/8” SAE Flat 1
29 F05011-4 Washer, 3/8” Split Lock 1
30 F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 1
31 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head 1
32 003914 Ball, 3/16” Dia. Nylon 2
33 F05011-14 Washer, 1/4” Split Lock 2
34 F05005-15 Bolt, 1/4-20 x 1/2” Hex Head 2
35 003994 Bolt, Blade Guide Block Mount 1
36 042867 Washer, #10 Brass 1
37 F05004-240 Bolt, #10-32 x 1 1/4” Hex Head Stainless 1
Steel
38 044057 Screw, Lower Block Adjustment 1
39 F05004-200 Screw, #10-32 x 3/8” Socket Head Stain- 1
less Steel
40 F05011-17 Washer, 5/16” SAE Flat 1

Blade Guide Rollers & Arm WM doc 5/11/23 2-2

 Blade Guide Rollers & Arm
2 Blade Guide Assembly, Idle Side

REF PART # DESCRIPTION COMMENTS QTY.

41 F05011-13 Washer, 5/16” Split Lock 1
42 052355 Block, Blade Guide Wear (Standard for 1 1/4” 2
Use kit 006382 to convert rollers
Blades) and guide blocks for both blade
052309 Block, Blade Guide Wear (Optional for 1 1/2” guides for 1 1/2" blades. 2
Blades) EZ-Glide blocks 036347 are
available.
036347 Block Assembly, 1” Sq. EZ-Glide Wear 2
43 035799 Block, Blade Guide Alignment 1
44 F05011-20 Washer, #10 Split Lock 1
45 F05004-152 Screw, #10-32 x 5/8” Hex Head 1
46 044064 Adjustment Tool, Lower Guide Block 1
035248 Shim, .008" Blade Guide Block Spacer 1

Drive Side Blade Guide Parts (See Section 2.1)

016568 ROLLER ASSEMBLY, BLADE GUIDE RELUBE (OPTIONAL FOR USE WITH 1 1
1/4” OR 1 1/2” BLADES)
057405 ROLLER ASSEMBLY, EXTENDED BLADE (OPTIONAL FOR USE WITH 1 1
GUIDE RELUBE 1/2” BLADES)
057407 Bearing Kit, Relube Blade Guide Rebuild 1
47 P04252 Washer, 5/8" White Felt 1
48 F04254-1 Ring, 1 1/8" Interior Retaining 1
49 015975 Bearing, R8-2RS Blade Guide Available in assemblies only. 2
Bearing must be modified for
use with relube roller assem-
blies. Remove (1) seal from
each bearing, place open sides
facing each other and place
spacer 035411 between bear-
ings.
50 P06455 Washer, 5/8" Gray Felt 1
51 035411 Spacer, Blade Guide Bearing 1
057407-1507 Instruction Sheet, Blade Guide Rebuild 1
52 035426 Roller, Flanged Blade Guide (Relube 1 1/4” & Available in assemblies only. 1
1 1/2” blade)
057402 Roller, Flanged Blade Guide (Relube 1 1/2” Available in assemblies only. 1
blade)
A04925-364 Instruction Sheet, Blade Guide Roller 1
Replacement
53 036161 BOLT, BLADE GUIDE ROLLER (RELUBE ONLY) 1
54 P05060 FITTING, 1/4-28 GREASE (RELUBE ONLY) 1

2-3 WM doc 5/11/23 Blade Guide Rollers & Arm

 Blade Guide Rollers & Arm
Blade Guide Assembly, Drive Side 2
2.2 Blade Guide Assembly, Drive Side

23 49
8
50
22 48 53
6
21 6 8
2
20 52
51
6 54
7
55
1
5 Optional Relube
9
6 24 Blade Guide Roller
25
8 11
4
3
17
41 12
13
26 38 14
42 16
31
32
30 37 15
29 10
36 17
27
28 33 19
34 18
44 35

39
45
40 3H0993C
46
43
47

REF PART # DESCRIPTION COMMENTS QTY.

1 016548 BLOCK, BOLT ON BLADE GUIDE MOUNT 1
2 003964 BRACKET WELDMENT, INNER BLADE GUIDE 1
MOUNT
3 F05011-4 WASHER, 3/8” SPLIT LOCK 2
4 F05007-7 BOLT, 3/8-16 X 1” HEX HEAD 2
003905 GUIDE ASSEMBLY, DRIVE SIDE BLADE 1
ROLLER
003910 Block Assembly, Blade Guide Mount 1
5 003911 Block Weldment, Blade Guide Mount Available in assemblies only. 1
6 F05010-17 Nut, 5/16-18 Hex 4
7 F05006-122 Screw, 5/16-18 x 1” Socket Head Flat 1
Point Stainless Steel Set
8 F05006-88 Bolt, 5/16-18 x 1” Hex Head Stainless 3
Steel
9 003913 Shaft Weldment, Drive Side Guide 1
10 003916 Plate, Blade Guide Deflector 1
11 F05006-101 Bolt, 5/16-18 x 3/4” Hex Head w/Flat & Lock 1
Washer

Blade Guide Rollers & Arm WM doc 5/11/23 2-4

 Blade Guide Rollers & Arm
2 Blade Guide Assembly, Drive Side

REF PART # DESCRIPTION COMMENTS QTY.

A04925 Roller Assembly, Blade Guide (standard for Use kit 006382 to convert the 1
use with 1 1/4” & 1 1/2” blades) rollers and guide blocks for both
blade guides for 1 1/2" blades.
014299 Roller Assembly, Extended Blade Guide 1
Optional relube versions of each
(optional for use with 1 1/2” blades)
roller configuration are also
available.
K07079 Bearing Kit, Blade Guide Rebuild 1
12 P04252 Washer, 5/8" White Felt 1
13 F04254-1 Ring, 1 1/8" Interior Retaining 1
14 015975 Bearing, R8-2RS Blade Guide Available in assemblies only. 2
15 P06455 Washer, 5/8" Gray Felt 1
F05005-105 Screw, 1/4-28 x 1/4” Socket Head 1
Cup Point Set Black Oxide
057407-1507 Instruction Sheet, Blade Guide 1
Rebuild
16 S04250 Roller, Flanged Blade Guide (1 1/4” & 1 Available in assemblies only. 1
1/2” blade)
014298 Roller, Flanged Blade Guide (1 1/2” Available in assemblies only. 1
blade)
A04925-364 Instruction Sheet, Blade Guide Roller 1
Replacement
17 S04253 Spacer, Blade Guide 2
18 F05011-125 Washer, 1/2” Nord-Lock 1
19 F05008-10 Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 1
20 F05011-17 Washer, 5/16” SAE Flat 2
21 F05011-13 Washer, 5/16” Split Lock 2
22 F05006-93 Bolt, 5/16-18 x 1 1/4” Hex Head 2
23 035656 Bolt, Blade Guide Vertical Adjustment 1
24 F05010-17 Nut, 5/16-18 Hex 1
25 F05006-136 Bolt, 5/16-18 x 2 3/4” Hex Head Full Thread 1
006325 GUIDE KIT, HIGH-PERFORMANCE BLADE Requires LMS blade lube sys- 1
GUIDE (OPTIONAL) tem. Use kit 006325 to upgrade
to High-Performance. If not
already equipped add LMS kit.
003927 Block Assembly, Drive Side Blade Guide 1
26 003915 Plate, Block Tilt Adjustment 1
27 003909 Block, Guide Block Mount 1
28 F05012-22 Pin, 3/16” x 5/8” Roll 2
29 F05011-3 Washer, 3/8” SAE Flat 1
30 F05011-4 Washer, 3/8” Split Lock 1
31 F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 1
32 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head 1
33 003914 Ball, 3/16” Dia. Nylon 2
34 F05011-14 Washer, 1/4” Split Lock 2
35 F05005-15 Bolt, 1/4-20 x 1/2” Hex Head 2
36 003994 Bolt, Blade Guide Block Mount 1
37 042867 Washer, #10 Brass 1
38 F05004-240 Bolt, #10-32 x 1 1/4” Hex Head Stainless 1
Steel
39 044057 Screw, Lower Block Adjustment 1
40 F05004-200 Screw, #10-32 x 3/8” Socket Head Stain- 1
less Steel
41 F05011-17 Washer, 5/16” SAE Flat 1

2-5 WM doc 5/11/23 Blade Guide Rollers & Arm

 Blade Guide Rollers & Arm
Blade Guide Assembly, Drive Side 2
REF PART # DESCRIPTION COMMENTS QTY.
42 F05011-13 Washer, 5/16” Split Lock 1
43 052355 Block, Blade Guide Wear (Standard for 1 1/4” Use kit 006382 to convert the 2
Blades) rollers and guide blocks for both
blade guides for 1 1/2" blades.
052309 Block, Blade Guide Wear (Optional for 1 1/2” 2
Optional relube versions of each
Blades)
roller configuration are also
036347 Block Assembly, 1” Sq. EZ-Glide Wear available. 2

44 035799 Block, Blade Guide Alignment 1

45 F05011-20 Washer, #10 Split Lock 1
46 F05004-152 Screw, #10-32 x 5/8” Hex Head 1
47 044064 Adjustment Tool, Lower Guide Block 1
035248 Shim, .008" Blade Guide Block Spacer 1

Idle Side Blade Guide Parts (See Section 2.1)

016568 ROLLER ASSEMBLY, BLADE GUIDE RELUBE Use kit 006382 to convert the 1
(OPTIONAL FOR USE WITH 1 1/4” OR 1 1/2” rollers and guide blocks for both
BLADES) blade guides for 1 1/2" blades.
057405 ROLLER ASSEMBLY, EXTENDED BLADE Optional relube versions of each 1
GUIDE RELUBE (OPTIONAL FOR USE WITH 1 roller configuration are also
1/2” BLADES) available.

057407 Bearing Kit, Relube Blade Guide Rebuild 1

48 P04252 Washer, 5/8" White Felt 1
49 F04254-1 Ring, 1 1/8" Interior Retaining 1
50 015975 Bearing, R8-2RS Blade Guide Available in assemblies only. 2
Bearing must be modified for
use with relube roller assem-
blies. Remove one seal from
each bearing, place open sides
facing each other and place
spacer 035411 between bear-
ings.
51 P06455 Washer, 5/8" Gray Felt 1
52 035411 Spacer, Blade Guide Bearing 1
057407-1507 Instruction Sheet, Blade Guide Rebuild 1
53 035426 Roller, Flanged Blade Guide (Relube 1 1/4” & Available in assemblies only. 1
1 1/2” blade)
057402 Roller, Flanged Blade Guide (Relube 1 1/2” Available in assemblies only. 1
blade)
A04925-364 Instruction Sheet, Blade Guide Roller 1
Replacement
54 036161 BOLT, BLADE GUIDE ROLLER (RELUBE ONLY) 1
55 P05060 FITTING, 1/4-28 GREASE (RELUBE ONLY) 1

Blade Guide Rollers & Arm WM doc 5/11/23 2-6

 Blade Guide Rollers & Arm
2 Blade Guide Arm Drive Assembly

2.3 Blade Guide Arm Drive Assembly

4 18
20
3
6
15

3H0538-2G
18 17
14
4
16
3 19
13 12
10 11
9 2
5
8
1

21
7

REF PART # DESCRIPTION COMMENTS QTY.

1 P09984 CHAIN, #25 X 20 1/4" 1
2 P09983 LINK, #25 MASTER 1
3 F05006-28 BOLT, 5/16-18 X 2 3/4" HEX HEAD GRADE 5 4
4 F05011-17 WASHER, 5/16" SAE FLAT 4
5 R01897 TUBE, 3/8" X 1/2" NEOPRENE 2.5ft
6 P07584 CLAMP, 1/2" COATED EMT 2
7 F05089-1 WRAP, 1/4" X 6" TIE 2
015989 DRIVE ASSEMBLY, BLADE GUIDE ARM 1
079215 Motor Assembly, Blade Guide Arm Replace- 1
ment
8 079214 Motor, Current Applications 1/30HP 1
12VDC Gear
061232 Gear Kit, Motor Replacement (Cur- 1
rent Application)
061234 Brush Kit, Gear Motor Replacement 1
(Current Application)
061233 Shaft Kit, Gear Motor Replacement 1
(Current Application)
9 F04875-1 Connector, 14 Gauge Butt 2
10 P09970 Sprocket, Gear Motor #25 14-Tooth 1
11 F05004-274 Screw, #10-24 x 1/4” Full Dog Point 2
Socket Set
12 F05004-60 Screw, #10-32 x 1/2" Hex Head 4
13 F05011-20 Washer, #10 Split Lock 4
A10365-296 Instruction Sheet, Blade Guide Arm 1
Motor

2-7 WM doc 5/11/23 Blade Guide Rollers & Arm

 Blade Guide Rollers & Arm
Blade Guide Arm Drive Assembly 2
REF PART # DESCRIPTION COMMENTS QTY.
14 015939 Bracket, Blade Guide Arm Motor Mount 1
15 S09999 Roller, Blade Guide Arm Chain Idler 1
16 F05006-3 Bolt, 5/16-18 X 3 1/2" Hex Head Full Thread 1
17 S09996 Spacer, 5/16" I.D. X 1 1/2" 1
18 F05011-17 Washer, 5/16" SAE Flat 2
19 F05011-13 Washer, 5/16" Split Lock 1
20 F05010-58 Nut, 5/16-18 Hex Nylon Lock 1
21 S11617 COVER, BLADE GUIDE ARM MOTOR 1
S12029 GUARD, BLADE GUIDE ARM (G.S. ONLY) 1

Blade Guide Rollers & Arm WM doc 5/11/23 2-8

 Blade Guide Rollers & Arm
2 Blade Guide Arm

2.4 Blade Guide Arm

2
1
2
4
5
11
3
11 5 4
6 12
13 9 3
12 13
5 10

5
8 10
6 5
7 89
5 7 3H0992-1

REF PART # DESCRIPTION COMMENTS QTY.

1 003972 BLADE GUIDE ARM WELDMENT 1
007040 BLADE GUIDE ARM WELDMENT (WIDE HEAD 1
ONLY)
2 W09067 BOLT, BLADE GUIDE ARM ROLLER CAM 4
3 F05011-5 WASHER, 5/8" SAE FLAT 4
4 F05011-26 WASHER, 5/8" EXTERNAL STAR 4
5 F05010-11 NUT, 5/8-18 HEX JAM 12
6 F05011-25 WASHER, 5/8" INTERNAL STAR 8
A09059 ROLLER ASSEMBLY, BLADE GUIDE ARM WITH 2
BEARING
7 S07989 Roller, Blade Guide Arm V-Groove Available in assemblies only. 1
8 P06030-1 Bearing, 6203-2NSL 5/8" I.D. Available in assemblies only. 1
9 F04254-8 Ring, 1.575” ID Beveled 5002-156 Retaining 1
A09932 ROLLER ASSEMBLY, BLADE GUIDE ARM WITH 2
BEARING AND SPROCKET
10 S09930 Roller, Blade Guide Arm Drive Available in assemblies only. 1
11 P06030-1 Bearing, 6203-2NSL 5/8" I.D. Available in assemblies only. 1
12 S09931 Sprocket, #25 26-Tooth Available in assemblies only. 1
13 F04254-8 Ring, 1.575” ID Beveled 5002-156 Retaining 1

2-9 WM doc 5/11/23 Blade Guide Rollers & Arm

 Blade Wheel & Tensioner
Blade Drive Assembly 3
SECTION 3 BLADE WHEELS & TENSIONER
3.1 Blade Drive Assembly

19
16

17
13
12
18 15 15 14

10 8 20
3 1
4
11 6
13 15 6
5 2
27
9 21
7
10 5 22 23
3H0899-1B 25 26

24

REF PART # DESCRIPTION COMMENTS QTY.

016393 BEARING ASSEMBLY, BLADE WHEEL DRIVE 1
016392 Bearing Assembly, Cylindrical Drive Available in assemblies only. 1
1 016391 Housing, Blade Wheel Drive Bearing Available in assemblies only. 1
2 014005 Shaft, Blade Wheel Drive Available in assemblies only. 1
3 P10205 Bearing, Blade Wheel Drive #MU1308TV 1
4 016055 Bearing, Blade Wheel Drive #6308 C3 1
Open
5 F04254-17 Ring, 90mm Interior Retaining #I17 2
6 P10206 Seal, Drive Bearing #CR15890 2
7 016330 Fitting, 1/4” NPT x 3/8” Hose Barb Elbow 1
8 016331 Fitting, 1/4” NPT x 3/8” Hose Barb Vented 1
Elbow
9 016394 Hose, Oil Level Viewer 1
10 P649 Clamp, 7/32-5/8” Hose 2
11 017470 Decal, Oil Level Gauge 1
016393-555 Instruction Sheet, Drive Bearing Replacement 1
12 F05004-170 SCREW, 1/2-20 X 1 1/2” CONE POINT SET 1
13 F05008-108 BOLT, 1/2-20 X 1 1/4” HEX HEAD GRADE 5 4
14 F05008-49 BOLT, 1/2-20 X 1 3/4” HEX HEAD GRADE 5 1
15 F05010-16 NUT, 1/2-20 HEX JAM 6
014562 WHEEL KIT, DRIVE SIDE BLADE 1
16 016284 Wheel, Drive Side Blade Available in assemblies only. 1
17 016270 Bushing, Modified 1 9/16” SD 1
18 S12892 Key, 3/8” x 3/8” x 1 5/8” 1

Blade Wheel & Tensioner WM doc 5/11/23 3-1

 Blade Wheel & Tensioner
3 Blade Drive Assembly

REF PART # DESCRIPTION COMMENTS QTY.

K12897-488 Instruction Sheet, Drive Side Blade Wheel 1
Replacement
19 P04185 BELT, BLADE WHEEL B57 1
20 BELT, DRIVE (See Section 5) FOR PART #
21 016531 SHEAVE, 5V12.5X3 BRAKE COMBO 1
22 016532 BUSHING, SF X 1 9/16” 1
23 014391 STRAP, METAL-BACKED BRAKE 1
24 017953 PLATE, BUSHING KEY RETAINER 1
25 F05011-4 WASHER, 3/8” SPLIT LOCK 3
26 F05007-27 BOLT, 3/8-16 X 3/4” HEX HEAD 3
27 014693 KEY, 3/8” X 3/8” X 1 7/8” 1

3-2 WM doc 5/11/23 Blade Wheel & Tensioner

 Blade Wheels & Tensioner
Idle Blade Wheel Assembly 3
3.2 Idle Blade Wheel Assembly

4 5

9
6

13
12
3

10
8

10
12
SM0254B
11
9
REF PART # DESCRIPTION COMMENTS QTY.
016120 WHEEL ASSEMBLY, IDLE SIDE BLADE 1
1 016013 Wheel, Idle Side Blade Available in assemblies only. 1
2 016014 Bearing, Idle Side Blade Wheel #5309-2RS, 1
C3, SRI-2 Grease
3 F04254-28 Ring, 100mm Internal Retaining Beveled 1
016441 SHAFT KIT, IDLE BLADE WHEEL 1
4 016397 Washer, 13/32” I.D. x 2 3/16 O.D. x 1/4” 1
5 F05007-64 Bolt, 3/8-16 x 1" Flat Head Socket 1
6 016398 Shaft, Idle Side Blade Wheel 1
7 P04185 BELT, BLADE WHEEL B57 1
8 016103 HOUSING, IDLE BLADE WHEEL SHAFT 1
9 F05008-53 BOLT, 1/2-20 X 1 1/2” HEX HEAD GRADE 5 2
10 F05010-16 NUT, 1/2-20 HEX JAM 4
11 F05008-111 BOLT, 1/2-20 X 3 3/4” HEX HEAD FULL THREAD 1
GRADE 2
12 S04253 SPACER, 1/2" I.D. FLANGED 2
13 F05011-9 WASHER, 1/2" SPLIT LOCK 1

Blade Wheels & Tensioner WM doc 5/11/23 3-3

 Blade Wheels & Tensioner
3 Hydraulic Blade Tensioner Assembly

3.3 Hydraulic Blade Tensioner Assembly

18
13
15
16 17
14 11
7 9
19 20
10
21

11 22

12
5 6 23
1
4
2 3H0041E

8
3

REF PART # DESCRIPTION COMMENTS QTY.

A10136 HYDRAULIC BLADE TENSIONER ASSEMBLY 1
A12294 Handle Assembly, Hydraulic Blade Tensioner 1
Screw
1 S10056 Screw, Hydraulic Blade Tensioner Available in assemblies only. 1
2 S08174 Handle, Hydraulic Tensioner Screw 1
3 P08072 Sleeve, Plastic Handle 1
4 F05012-19 Pin, 3/16" x 7/8" Roll 1
5 P02720 Ball, 1/2" Steel 1
6 S10062 Block, Threaded Tensioner End Available in assemblies only. 1
7 P05060 Fitting, 1/4-28 Grease 1
A12294-518 Instruction Sheet, Tensioner Screw 1
8 F05006-43 Bolt, 5/16-18 X 7 1/2" Hex Head Grade 5 4
9 S10060 Piston, Hydraulic Tensioner Front 2 3/4" Long 1
10 S10061 Block, Piston Guide 1
003224 Seal Kit, Hydraulic Tensioner 1
5 P02720 Ball, 1/2" Steel 1
11 P10051 Seal, 1" Diameter 2
12 P10053 Wiper, 1" Diameter 1
13 P10377 Ring, 5/8" X 3/32" Square "O" 1
14 S10140 Block, Hydraulic Tensioner Gauge Mounting 1
15 P10052 Gauge, 3000 P.S.I. Hydraulic 1
16 P10065 Plug, Hydraulic Tensioner Fill 1
016329 Block Assembly, Rear Tensioner Piston 1
17 S10142 Block, Rear Tensioner Piston Available in assemblies only. 1
18 P10065 Plug, Hydraulic Tensioner Fill 1

3-4 WM doc 5/11/23 Blade Wheels & Tensioner

 Blade Wheels & Tensioner
Hydraulic Blade Tensioner Assembly 3
REF PART # DESCRIPTION COMMENTS QTY.
19 S10059 Piston, Hydraulic Tensioner Rear 3 5/8" Long 1
20 S10089 Block, Rear Piston End 1
21 F05004-43 Bolt, #10-24 X 1" Socket Button Head 4
22 F05006-28 Bolt, 5/16-18 X 2 3/4" Hex Head Grade 5 4
23 P10147 Decal, Hydraulic Tension Caution 1
A10136-272 Instruction Sheet, Hydraulic Tensioner Installa- 1
tion

Blade Wheels & Tensioner WM doc 5/11/23 3-5

 Saw Head
4 Middle Throat Screw

SECTION 4 SAW HEAD FRAME

4.1 Middle Throat Screw

1
SM0122B

REF PART # DESCRIPTION COMMENTS QTY.

1 F05007-18 SCREW, 3/8-16 X 1 1/4" OVAL POINT SOCKET 1
SET
2 F05010-29 NUT, 3/8-16 HEX JAM 1

4-1 WM doc 5/11/23 Saw Head

 Saw Head
Water Lube Solenoid Valve 4
4.2 Water Lube Solenoid Valve

REF PART # DESCRIPTION COMMENTS QTY.

016280 Solenoid Valve, Water Lube Kit 1
1 F05004-60 Bolt, #10-32x1/2 HH 2
2 F05011-20 Washer, #10 Split Lock 2
3 F05011-18 Washer, #10 SAE Flat 2
4 P04682 Fitting, 3/8 Barb 1/4NPT Male 2
133071 Assy, Water Lube Solenoid Electrical 1
5 016140 Solenoid Valve, 2-Way NC 1/4 Port 12 VDC 1
6 F04875-13 Connector, TT-Tap 14-16Awg 2
7 F05708-21R Terminal, 1/4 18-22Ga Quick Female FI 2
8 R02374 Conduit, 1/2" Flex Loom 1
9 F05089-3 Tie Wrap, 3/16x5 1/2 UV Blk 1
024123 Diode Assy, Inductive Kick Protection 1
10 F05708-22R Terminal, 1/4 18-22 Ga Qk Male FI Reel 2
11 R01915-3_3 Wire, 18AWG Stranded Red GXL 1
12 R01950-4_2_14 Tubing, 1/4" IDx2.25 Heat Shrink 1
13 024032 Conn, 14-16 AWG Parallel Splice 2
14 E05909 DIODE, 1N4003 1
15 R01915-0_3 Wire,18AWG Stranded Black 1

Saw Head WM doc 5/11/23 4-2

 Saw Head
4 Clutch Pivot

4.3 Clutch Pivot

6
1

2
3

4
3H0756-5

REF PART # DESCRIPTION COMMENTS QTY.

1 016296 Plate Weldment, Clutch Pivot 1
2 P737 Bushing, Clutch/Brake Pivot 2
3 P116 Washer, Clutch/Brake Pivot 1
4 F05012-49 Pin, 1/8" X 1 1/2" Cotter 1
5 F05010-83 Nut, 7/16-20 Hex Nylon Lock 1
6 F05007-120 Bolt, 7/16-20 x 2” SOcket Head 1

4-3 WM doc 5/11/23 Saw Head

 Saw Head
Clutch Mount Assembly 4
4.4 Clutch Mount Assembly

8
7

6
1

2
3H0756-2B

REF PART # DESCRIPTION COMMENTS QTY.

1 F05010-83 Nut, 7/16-20 Hex Nylon Lock 1
2 F05007-55 Bolt, 7/16-20 X 1 1/2" Socket Head 1
3 W12411 Bracket, Clutch Mount 1
4 F05007-157 Bolt, 3/8-16 x 2 1/2” Hex Head 1
5 016316 Spacer, Motor Mount Vibration Bushing 1
6 P05032 Bushing, Motor Mount Vibration 1
7 021276 Washer, .40" I.d. X 1.44" O.d. X .18" Thick 1
8 F05010-10 Nut, 3/8-16 Nylon Lock 1

Saw Head WM doc 5/11/23 4-4

 Saw Head
4 Brake Assembly

4.5 Brake Assembly

2
1

8
11
9
7 12
8

10

3H0366

REF PART # DESCRIPTION COMMENTS QTY.

014441 Strap Retrofit, Super Brake Service Kit 1
1 F05010-10 Nut, 3/8-16 Nylon Lock 2
2 F05011-3 Washer, 3/8” SAE Flat 2
3 014395 Bracket, Upper Super Brake Strap Mount 1
4 F05007-127 Bolt, 3/8-16 x 1 1/4” Carriage Head Grade 5 2
5 F05012-81 Pin, 1/2” x 2 1/4” Clevis 1
6 F05012-1 Pin, 1/8” x 1” Cotter 1
7 014391 Strap, Upper Pivot Metal Brake 1
8 F05010-8 Nut, 1/2-13 Nylon Lock 2
9 F05008-33 Bolt, 1/2-13x1 1/2 HH Gr5 1
10 F05008-37 Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 1
11 S04195 Plate, Brake Strap Clamp 1
12 014392 Bracket, Lower Super Brake Strap Mount 1

4-5 WM doc 5/11/23 Saw Head

 Saw Head
Brake Assembly (DC Only) 4
4.6 Brake Assembly (DC Only)
9
17
8

10

7
2 3 16
4 18
6 18

5
11
14 15

13 19

600035B
12
REF PART # DESCRIPTION COMMENTS QTY.
034886 BRAKE ASSEMBLY, LT60/70 1
1 016488 Block, Blade Wheel Brake 6
2 017838 Washer, 21/32” x 2 1/4” x 3/16” 1
3 034685 Washer, 21/32” x 1 5/8” x 1/4” 1
4 034883 Arm Weldment, Pivot Brake 1
5 034885 Shaft, Pivot Brake 1
034892 Linkage Assembly, Pivot Brake 1
6 034891 Arm Weldment, Pivot Brake Lik 1
7 F05010-38 Nut, 7/16-20 Jam 1
8 F05010-87 Nut, 7/16-20 Left Hand Jam 1
9 P11578 Rod End, 7/16-20 Left Hand Male 1
10 S11577 Turnbuckle, 3” Adjustment 1
11 038090 Collar, 1” Lock 1
12 F05004-2 Bolt, #10-24 x 1” Socket Head 12
13 F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 1
14 F05010-10 Nut, 3/8-16 Hex Nylon Lock 1
15 F05010-14 Nut, #10-24 Self-Locking Hex 12
16 F05010-71 Nut, 5/8-18 Hex Nylon Lock 1
17 F05010-83 Nut, 7/16-20 Hex Nylon Lock 1
18 P109 Bushing, 1” ID x 1 1/4” OD Flanged 2
19 F05011-3 Washer, 3/8” SAE Flat 3

Saw Head WM doc 5/11/23 4-6

 Saw Head
4 Board Return Assembly

4.7 Board Return Assembly

28 21 32 12
33
17 26 13 22
16 2
5
30 25
24 4
31
19 23
27 18
29
Align set screw with 20
flat on Motor Shaft 15 3 1
17 4
16 2

9
3H0385C
8 6 11
12
9
7

13
36 14
13

10

5
34
35

REF PART # DESCRIPTION COMMENTS QTY.

015209 RETURN ASSEMBLY, BOARD 1
1 015215 Mount Weldment, Board Return 1
2 F05007-1 Bolt, 3/8-16 x 3” Full Thread Hex Head 4
3 015336 Washer, 1/8” x 1 1/4” 2
4 F05010-10 Nut, 3/8-16 Hex Nylon Lock 4
5 F05011-3 Washer, 3/8” Flat 5
6 016272 Rod Kit, Board Return Replacement Pivot 1
7 P05060 Fitting, 1/4-28 Grease 1
8 F05012-16 Pin, 3/16 x 1 1/4” Roll 1
9 F05011-19 Washer, 5/8” x 15/16” x .094 Nylon 2
10 015210 Arm Weldment, Board Return 1
11 F05005-1 Screw, 1/4-20 x 3/4” Full Thread Hex Head 1
12 F05011-17 Washer, 5/16” SAE Flat 3
13 F05010-9 Nut, 1/4-20 Self-Locking 3
14 F05011-11 Washer, 1/4” SAE Flat 2
15 015007 Guard, Board Return Belt 1
16 F05004-60 Screw, #10-32 x 1/2” Hex Head Machine 4
17 F05011-20 Washer, #10 Split Lock 4
18 015074 Pulley, 1.42” x .32” 1

4-7 WM doc 5/11/23 Saw Head

 Saw Head
Board Return Assembly 4
REF PART # DESCRIPTION COMMENTS QTY.
19 F05005-105 Screw, 1/4-28 x 1/4” Socket Head Cup Point 1
Set
20 F05005-89 Bolt, 1/4-20 x 1” Socket Head 1
21 015477 Belt, 3L190 1
22 015224 Pulley, OK50 x 1/2” Modified 1
23 015221 Bolt, Idler Pulley Pivot 1
24 P05135 Bushing, 5/8” x 7/8” x 1/2” Bronze 1
25 F05011-2 Washer, 1/2” SAE Flat 1
26 F05010-79 Nut, 1/2-20 Nylon Lock Jam 1
27 015220 Plate, Motor Pivot 1
28 F05007-52 Bolt, 3/8-16 x 1” Socket Head 1
29 F05010-25 Nut, 3/8-16 Self-Locking 1
30 079214 Motor, Current Applications 1/30HP 12VDC 1
Gear
061232 Gear Kit, Motor Replacement 1
061234 Brush Kit, Gear Motor Replacement 1
061233 Shaft Kit, Gear Motor Replacement 1
31 015479 Spring, 3/4” x 2 7/8” x 12 Gauge 1
32 F05005-101 Bolt, 1/4-20 x 1” Hex Head Grade 5 1
33 016090 Cable, Board Return 1
34 F05011-4 Washer, 3/8” Split 3
35 F05007-7 Bolt, 3/8-16 x 1” Hex Head 3
36 015652 Angle, Board Return 1

Saw Head WM doc 5/11/23 4-8

 Saw Head
4 Water Lube Assembly (Gas Only)

4.8 Water Lube Assembly (Gas Only)

2
3

4
5 3H1167

REF PART # DESCRIPTION COMMENTS QTY.

1 014642 BOTTLE ASSEMBLY, WATER LUBE W/CAP 1
061372 O-ring, Water Bottle Cap If the water bottle cap keeps 1
leaking, add this o-ring to the
cap. Leave the existing o-ring
installed.
2 014636 FITTING, 3/4FPT X 3/4MPT 1
3 014100 FITTING, WATER LUBE SHUTOFF VALVE 1
4 016086 FILTER, WATER LUBE Filter recommended for LT50- 1
Super models to prevent debris
from entering water lube sole-
noid valve.
5 014113 FITTING, 5/8” NPT TO 3/8” HOSE BARB 1
6 R01885 TUBING, WATER LUBE 3/8” I.D. 7 ft.
CBOTTLE COVER, 5 GAL. WATER BOTTLE OPTIONAL 1
(NOT SHOWN)

4-9 WM doc 5/11/23 Saw Head

 Saw Head
Water Lube Assembly (Diesel & Electric Only) 4
4.9 Water Lube Assembly (Diesel & Electric Only)

13

7
14

15 4
3
7

16
5
17
6 4
8
18
9 3H0281D
5 12

8
9
11
12
8

9
10

REF PART # DESCRIPTION COMMENTS QTY.

A11685 TRAY ASSEMBLY, FUEL TANK/WATER BOTTLE 1
1 S11684 Tray, Fuel Tank/Water Bottle 1
2 P11258 Strap, 24" Rubber (For Fuel Tank - See Engine 2
Manual)
3 P11668 Strap, 20" Rubber 2
4 F05005-34 Bolt, 1/4-20 X 1" Carriage Head 4
5 F05010-21 Nut, 1/4-20 Hex Lock 4
6 F05005-34 BOLT, 1/4-20 X 1" CARRIAGE HEAD 1
7 F05005-33 BOLT, 1/4-20 X 1/2" CARRIAGE HEAD 2
8 P07584 CLAMP, 1/2" EMT HOSE 3
9 F05011-11 WASHER, 1/4" SAE FLAT 3

Saw Head WM doc 5/11/23 4-10

 Saw Head
4 Water Lube Assembly (Diesel & Electric Only)

REF PART # DESCRIPTION COMMENTS QTY.

10 F05010-21 NUT, 1/4-20 HEX LOCK 1
11 P07461 STRAP, 15" RUBBER 1
12 F05010-9 NUT, 1/4-20 SELF-LOCKING 2
13 014642 BOTTLE ASSEMBLY, WATER LUBE W/CAP 1
061372 O-ring, Water Bottle Cap If the water bottle cap keeps 1
leaking, add this o-ring to the
cap. Leave the existing o-ring
installed.
14 014636 FITTING, 3/4FPT X 3/4MPT 1
15 014100 FITTING, WATER LUBE SHUTOFF VALVE 1
16 016086 FILTER, WATER LUBE 1
17 014113 FITTING, 5/8” NPT TO 3/8” HOSE BARB 1
18 R01885 TUBING, WATER LUBE 3/8” I.D. 7 ft.

4-11 WM doc 5/11/23 Saw Head

 Saw Head
Saw Head Decals 4
4.10 Saw Head Decals
Burn H aza rd
Avoid cont act wit h an y
12
par t o f ho t en gine .

Failu re t o d o so may
r esul t in s erio us in jur y.
W oo d-Mi zer P rodu ct s, In c.
8 00 -5 25 -81 00 Re ord er #0 144 19

19 18
16
17

20
Moving Par ts Can Cr ush
An d Cut.
Make sure all guar ds and cover s

5
M ov ing P art s Ca n C rush
A nd C ut .

M ake sure all guards and covers

4 15
4
are in place and secure before ar e in place and secur e before

14
operating this machine. operatingthis machine.
Fail ur e to do so will result in Failure to doso w li l result in
serious injury. serious injury.
Wood -M i zer P ro duct s, In c. Wo od- M zi er Pr oduc ts, I nc.
800 -5 25- 8100 R eor der #0332 54 800- 525- 81 00 Re or der #0 33254

1
3
11 11
9
13 8

6
10
2 7
Du
st
co In sp
An
nt H d
be ain ec az P
Ke of fo met proar roje
Fa ep the re nt jecd ct
ilu ea
W re cle
sa ch fin tile
ile
800 ood sa
- 525- Mi ni to do wdar ofwm us ge
zer se rs
- 810 Pr ve so us ex ill. e
0 odu
cts
re m t. itin
, I nc. in ju ay g
R eor
ry. res
der
ult
#P1
175
4

3H0589-9

REF PART # DESCRIPTION COMMENTS QTY.

1 P10147 DECAL, BLADE TENSION CAUTION 1
2 P11754 DECAL, SAWDUST CHUTE WARNING 1
3 P12373 DECAL, BLADE TENSION RANGES 1
4 033254 DECAL, BLADE COVERS DANGER 2
5 S11752 DECAL, BLADE DANGER ARROW RIGHT 1
6 S11762 DECAL, UP/DOWN CAUTION 1
7 P11779 DECAL, BLADE START/STOP 1
8 P11790 DECAL, BLADE TENSION INFO 1
9 P12879 DECAL, TRU-SHARP INFO 1
10 P11789 DECAL, BLADE ALIGNMENT INFO 1
11 P07452 DECAL, RED REFLECTIVE 2” ROUND 2
12 014419 DECAL, HOT ENGINE WARNING 1
13 016072 DECAL, BOARD RETURN OPERATOR WARN- 1
ING
14 003235 DECAL, WOOD-MIZER WEBSITE 1
15 065582 DECAL, 30 YEAR LOGO 1
16 065027 DECAL, LT50 IDLE SIDE BLACK EURO STRIPE 1
17 065025 DECAL, LT40/50 WHITE WOOD-MIZER LOGO 1
18 065026 DECAL, LT40/50 DRIVE SIDE BLACK EURO 1
STRIPE
19 065028 DECAL, LT50 WHITE EURO LOGO 1
20 074335 DECAL, LT15/70 WIDE LOGO (WIDE HEAD 1
ONLY)

Saw Head WM doc 5/11/23 4-12

 Saw Head
4 Blade Housing Covers

4.11 Blade Housing Covers

3
5 6
14
11
15
4 13

2
9
10
12
10

8
3
7 6
12 2 4
1

12 5

3H0539-2F

REF PART # DESCRIPTION COMMENTS QTY.

015937 COVER ASSEMBLY, DRIVE SIDE BLADE HOUS- 1
ING WITH HANDLE
1 015911 Cover, Drive Side Blade Housing Available in assemblies only. 1
(Includes Cover Decal - (See
Section 4.10))
2 P08065 Handle, Blade Housing Cover 1
3 F05015-8 Screw, #8-32 X 3/8" Self-Tap 2
A12812 Pin Assembly, Cover Retainer 1
4 P05059 Pin, Safety Retainer 1
5 016030 Cable, 3/64” x 6” Lanyard 1
6 F05011-87 Washer, 1/2” ID x 1 1/8” OD x. 093” Rubber 1
A09419 COVER, IDLE SIDE BLADE HOUSING WITH 1
HANDLE
7 W09351 Cover, Idle Side Blade Housing Available in assemblies only. 1
(Includes Cover Decal - (See
Section 4.10))
2 P08065 Handle, Blade Housing Cover 1
3 F05015-8 Screw, #8-32 X 3/8" Self-Tap 2
A12812 Pin Assembly, Cover Retainer 1
4 P05059 Pin, Safety Retainer 1
5 016030 Cable, 3/64” x 6” Lanyard 1
6 F05011-87 Washer, 1/2” ID x 1 1/8” OD x. 093” Rubber 1
8 W07409 COVER, MIDDLE BLADE HOUSING 1
079509 COVER, MIDDLE BLADE HOUSING (WIDE HEAD 1
ONLY)

4-13 WM doc 5/11/23 Saw Head

 Saw Head
Blade Housing Covers 4
REF PART # DESCRIPTION COMMENTS QTY.
9 F05005-1 BOLT, 1/4-20 X 3/4" HEX HEAD 18
10 S07522 HINGE, MIDDLE BLADE HOUSING COVER 2
11 F05010-9 NUT, 1/4-20 SELF-LOCKING HEX 4
12 021145 NUT, COVER TURN 3
13 S04433 PLATE, IDLE BLADE WHEEL GUARD 1
14 F05010-58 NUT, 5/16-18 HEX NYLON LOCK 6
15 F05006-5 BOLT, 5/16-18 X 3/4” HEX HEAD GRADE 2 6

Saw Head WM doc 5/11/23 4-14

 Saw Head
4 Drive Belt Covers

4.12 Drive Belt Covers

1
1 8
1
9

2
7
4
5
1

6
3
3H0990-6B 5 1
1 4
1
REF PART # DESCRIPTION COMMENTS QTY.
1 F05005-134 BOLT, 1/4-20 X 3/4" HEX HEAD WITH CONICAL 15
WASHER
2 006026 GUARD WELDMENT, SUPER/REMOTE LOWER For sawmills equipped with 1
DRIVE BELT standard manual clutch handle
only. See Autoclutch Option
manual for alternate guards.
3 006025 MOUNT WELDMENT, LOWER DRIVE BELT 1
4 F05005-15 BOLT, 1/4-20 X 1/2” HEX HEAD 3
5 F05011-11 WASHER, 1/4” SAE FLAT 3
6 015654 GUARD WELDMENT, LOWER UP/DOWN 1
7 008776 GUARD, SUPER DRIVE PULLEY SIDE 1
8 059599 GUARD, DRIVE PULLEY TOP 1
9 074752 PLATE, LT40 BELT GUARD COVER 1

4-15 WM doc 5/11/23 Saw Head

 Saw Head
Sawdust Chute 4
4.13 Sawdust Chute

3
9
10

3H0539-1 5
6

REF PART # DESCRIPTION COMMENTS QTY.

1 015466 CHUTE WELDMENT, SAWDUST 1
2 F05006-5 BOLT, 5/16-18 X 3/4” HEX HEAD GRADE 2 2
3 F05011-17 WASHER, 5/16” SAE FLAT 2
4 F05010-20 NUT, 5/16-18 SELF-LOCKING HEX 2
5 F05015-7 BOLT, #10-24 X 1/2” SELF-TAPPING 2
6 016727 TUBING, RUBBER SAWDUST 1
P11668 STRAP, 20” RUBBER W/HOOK 1
F05005-3 BOLT, 1/4-20 X 1 1/4” HEX HEAD FULL THREAD 1
F05011-11 WASHER, 1/4” SAE FLAT 1
F05010-21 NUT, 1/4-20 LOCK 1

Saw Head WM doc 5/11/23 4-16

 Saw Head
4 Debarker Wire Box/Hole Plugs

4.14 Debarker Wire Box/Hole Plugs

1
4

2
3

3H0578-12

REF PART # DESCRIPTION COMMENTS QTY.

1 023616 BOX, DEBARKER WIRE STORAGE 1
2 F05007-29 BOLT, 3/8-16 X 2 3/4” HEX HEAD 2
3 F05011-3 WASHER, 3/8” SAE FLAT 2
4 F05010-10 NUT, 3/8-16 HEX NYLON LOCK 2
5 014537 PLUG, 13/32” PLASTIC HOLE 2

4-17 WM doc 5/11/23 Saw Head

 Control & Battery Boxes
Control Assembly 5
SECTION 5 CONTROL & BATTERY BOXES
5.1 Control Assembly

34

30
31

STOP!
A lways wea r eye, e ar,
res piration and foot
pr otection whe n
operating this ma chine .

Fa ilur e to do so ma y
r esult in injury.
Woo d-Mizer P rodu cts, Inc.
800-5 25-8100 Reorder #S117 53

Cru sh Hazard

29
Always put front
outri gger down before
moving cutting head from
the rest position.

Fai lure to do so may

result i n seri ous injury.
Wood-Miz er P roduc ts , Inc .
800-525-8100 Reorder#015400

7
6
8 13 12
10
21

4
11 5
6 14
2 15
15 9
2
17 22
4
4
3
20 3
18
1
19

4 24

28
26 27
3H1064-1B

25
23

32

33

REF PART # DESCRIPTION COMMENTS QTY.

015764 COVER, SAWMILL CONTROL CONSOLE 1
036352 COVER, SAWMILL CONTROL CONSOLE 1
W/ACCUSET
069426 CONTROL BOX ASSEMBLY, E25 DUAL-AXIS 1
069421 CONTROL BOX ASSEMBLY, G38 DUAL-AXIS 1
069422 CONTROL BOX ASSEMBLY, D35 DUAL-AXIS Replaced with D35 Tier4 Con- 1
(TIER2 ONLY) trol Box Assembly for the U.S.
only (LT40HD Super Rev.
K4.00+/LT50 Rev. A6.00+). See
Section Control Assembly (D35
Tier4 Only).
069422 CONTROL BOX ASSEMBLY, D47 DUAL-AXIS 1
069420 CONTROL BOX ASSEMBLY, D51 DUAL-AXIS 1
1 025823 Box Weldment, Sawmill Control Available in assemblies only. 1

Control & Battery Boxes WM doc 5/11/23 5-1

 Control & Battery Boxes
5 Control Assembly

REF PART # DESCRIPTION COMMENTS QTY.

2 006473 Panel, Control Box Side 2
3 015274 Gasket, Side Panel Control 2
4 F05015-17 Screw, #10-24 x 1/2" Pan Head 16
5 F05004-186 Screw, #10-24 x 1/2” Phillips Head 14
6 N/A Front Control Panel & Wiring Harnesses ((See 1
Section 5.5))
7 N/A Drum Switches ((See Section 5.3)) 1
8 F05004-3 Screw, #10-24 x 3/8” Phillips Pan Head 2
9 F05010-14 Nut, #10-24 Self Locking 2
10 F05004-148 Screw, #10-24 x 3/8” Phillips Pan Head 4
Machine with Neo Washer
11 F05010-14 Nut, #10-24 Self-Locking Hex 4
12 F05007-27 Bolt, 3/8-16 x 3/4” Hex Head 1
13 F05011-3 Washer, 3/8” SAE Flat 1
14 F05010-19 Nut, 3/8” Lock Nut 1
15 F05010-9 Nut, 1/4-20 Self Locking 4
16 F05011-11 Washer, 1/4” SAE Flat 4
17 F05011-69 Washer, 1/4” Interior Star Heavy Duty Lock 2
18 015266 Gasket, Front Access Panel 1
19 015376 Panel, Control Box Front Access 1
20 069412 Decal, Front Circuit Breaker ID (Super NR 1
Dual-Axis)
21 069414 Decal, Rear Circuit Breaker ID (Super NR 1
Dual-Axis)
22 N/A Circuit Breakers ((See Section 5.4)) 1
23 053355 Harness Assembly, Dual-Axis Motor Control 1
Non-Remote
24 015236 MOUNT WELDMENT, STANDARD CONTROL 1
BOX
25 F05010-20 NUT, 5/16-18 SELF-LOCKING HEX 4
26 F05007-52 BOLT, 3/8-16 X 1” SOCKET HEAD 6
27 F05011-4 WASHER, 3/8” SPLIT LOCK 6
28 F05011-36 WASHER, 3/8” EXTERIOR STAR LOCK 6
29 015400 DECAL, FRONT OUTRIGGER WARNING 1
30 S11753 DECAL, EAR/EYE PROTECTION WARNING 1
31 S12117 DECAL, 800 NUMBER 1
32 036381 PLATE, PEDESTAL COVER 1
33 F05015-17 SCREW, #10-24 X 1/2" PAN HEAD 2
34 N/A ACCUSET PARTS (See AccuSet 2 Manual) 1

5-2 WM doc 5/11/23 Control & Battery Boxes

 Control & Battery Boxes
Control Assembly (Tier4 Only) 5
5.2 Control Assembly (Tier4 Only)

47 44
STOP!
Always wear eye, ear,
respiration and foot
protection when
43
operating this machine.

7
Failure to do so may

42
result in injury.
Wood-Mi zer Product s, I nc .
Crush Hazard

6
800-525-8100 R eorder #S11753

4
Alway s put fr ont
outrigger down befor e
m ov ing cutting hea d from
the r est position.

Failure to do so may
r esult in se rious injury.
Woo d-Mizer Pr oducts, I nc.
800-5 25-8 100 Reord er #0 15400

10 12
8
21

5 29 4 24
11 4 33
15 14 13
2 6 28
15 9
22
17 34
4
3
20 35
18 27 30
25 36
1 26 32
19 31
37
4
41
3H1195-1 39 40

23 38

45
46

REF PART # DESCRIPTION COMMENTS QTY.

015764 COVER, SAWMILL CONTROL CONSOLE 1
036352 COVER, SAWMILL CONTROL CONSOLE 1
W/ACCUSET
073590 CONTROL BOX ASSEMBLY, D35 TIER4 1
DUAL-AXIS
1 025823 Box Weldment, Sawmill Control Available in assemblies only. 1
2 006473 Panel, Control Box Side 2
3 015274 Gasket, Side Panel Control 2
4 F05015-17 Screw, #10-24 x 1/2" Pan Head 16
5 F05004-186 Screw, #10-24 x 1/2” Phillips Head 14
6 N/A Front Control Panel & Wiring Harnesses ((See 1
Section 5.5))
7 N/A Drum Switches ((See Section 5.3)) 1
8 F05004-3 Screw, #10-24 x 3/8” Phillips Pan Head 2
9 F05010-14 Nut, #10-24 Self Locking 2
10 F05004-148 Screw, #10-24 x 3/8” Phillips Pan Head 4
Machine with Neo Washer
11 F05010-14 Nut, #10-24 Self-Locking Hex 4
12 F05007-27 Bolt, 3/8-16 x 3/4” Hex Head 1
13 F05011-3 Washer, 3/8” SAE Flat 1
14 F05010-19 Nut, 3/8” Lock Nut 1

Control & Battery Boxes WM doc 5/11/23 5-3

 Control & Battery Boxes
5 Control Assembly (Tier4 Only)

REF PART # DESCRIPTION COMMENTS QTY.

15 F05010-9 Nut, 1/4-20 Self Locking 4
16 F05011-11 Washer, 1/4” SAE Flat 4
17 F05011-69 Washer, 1/4” Interior Star Heavy Duty Lock 2
18 015266 Gasket, Front Access Panel 1
19 015376 Panel, Control Box Front Access 1
20 069412 Decal, Front Circuit Breaker ID (Super NR 1
Dual-Axis)
21 069414 Decal, Rear Circuit Breaker ID (Super NR 1
Dual-Axis)
22 N/A Circuit Breakers ((See Section 5.4)) 1
23 053355 Harness Assembly, Dual-Axis Motor Control 1
Non-Remote
073603 Box Assembly, Key Switch 1
24 078426 Control Box Weldment, Key/Hour 1
25 F05015-17 Bolt, #10-24x1/2 Ph Pan Hd, Type 23 4
26 033495 Panel Weldment, Side L.H. 1
27 015274 Gasket, Side Panel Control 97 1
28 033475 Grommet, 5/8 ID 3/16 GW Rubber 1
29 F05005-15 Bolt, 1/4-20x1/2 HH 2
30 F05010-9 Nut, 1/4-20 Keps 2
073597 Panel Assembly, Key Switch Box Frt 1
31 073598 Plate, Key Switch Box Front 1
32 073594 Decal, Key Switch 1
33 P04350 Switch, Key 1
34 015401 Digital Meter, Hour Rect Mount w/ 1
Gasket
35 F05015-28 Screw, #6-32x1/2 Plain PH T23 2
36 033488 Gasket, LMS Panel 1
37 015236 MOUNT WELDMENT, STANDARD CONTROL 1
BOX
38 F05010-20 NUT, 5/16-18 SELF-LOCKING HEX 4
39 F05007-52 BOLT, 3/8-16 X 1” SOCKET HEAD 6
40 F05011-4 WASHER, 3/8” SPLIT LOCK 6
41 F05011-36 WASHER, 3/8” EXTERIOR STAR LOCK 6
42 015400 DECAL, FRONT OUTRIGGER WARNING 1
43 S11753 DECAL, EAR/EYE PROTECTION WARNING 1
44 S12117 DECAL, 800 NUMBER 1
45 036381 PLATE, PEDESTAL COVER 1
46 F05015-17 SCREW, #10-24 X 1/2" PAN HEAD 2
47 N/A ACCUSET PARTS (See AccuSet 2 Manual) 1

5-4 WM doc 5/11/23 Control & Battery Boxes

 Control & Battery Boxes
Drum Switches 5
5.3 Drum Switches

7 5
8 3
2
7

4
1
3H0421

REF PART # DESCRIPTION COMMENTS QTY.

E20440 SWITCH ASSEMBLY, UP/DOWN DRUM 1
1 E20440-B Switch, S12 Bulk Drum Available in assemblies only. 1
2 P12570 Spring, Drum Switch 1
3 P12500 Handle, Drum Switch Replacement 1
E20439 SWITCH ASSEMBLY, POWER FEED DRUM 1
4 E20439-B Switch, S11 Bulk Drum Available in assemblies only. 1
5 P12570 Spring, Drum Switch 1
6 P12500 Handle, Drum Switch Replacement 1
7 F05011-41 WASHER, #8 SAE FLAT 6
8 A20463 CUP ASSEMBLY, DRUM SWITCH GREASE 1

Control & Battery Boxes WM doc 5/11/23 5-5

 Control & Battery Boxes
5 Circuit Breakers

5.4 Circuit Breakers

8 5

4
3
3
3

7
1 2
2

6
3H1064-3
6
REF PART # DESCRIPTION COMMENTS QTY.
015621 BREAKER ASSEMBLY, SAWMILL CONTROL 1
CIRCUIT
1 052826 Rail, Circuit Breaker 1
2 E20430 Breaker, 15 Amp Manual Reset 5
3 F05015-7 Screw, #10-24 x 1/2” Self-Tappipng 6
4 015527 BREAKER, 70 AMP MANUAL RESET PANEL 1
MOUNT
5 021253 BOOT, CIRCUIT BREAKER 2
6 F05004-3 SCREW, #10-24 X 3/8” PHILLIPS PAN HEAD 3
7 F05010-14 NUT, #10-24 SELF LOCKING 3
8 024246 BREAKER, 30A MANUAL RESET PANEL 1
MOUNT

5-6 WM doc 5/11/23 Control & Battery Boxes

 Control & Battery Boxes
Front Panel Assembly & Harnesses 5
5.5 Front Panel Assembly & Harnesses

11
2
7
10 6 1
4
16 14
7

9
6
17

13
12
5

3
3H1067B

15
8
5
REF PART # DESCRIPTION COMMENTS QTY.
069417 PANEL ASSEMBLY, CONTROL FRONT E25 1
069416 PANEL ASSEMBLY, CONTROL FRONT 1
(G38/D47/D51)
1 015270 Gasket, Front Panel 1
2 015302 Panel Weldment, Control 1
3 024450-1 Switch Assembly, Feed Rate 1
4 P06257 Knob, Feed Rate With Set Screw 1
5 024200 Switch, Toggle 2
6 P02575 Boot, Toggle Switch Rubber 2
7 P05251-1 Washer, 1/2 x 3/4 x 1/16 Nylon 2
8 P04350 Switch, Key 1
9 015401 Meter, Hour 1
10 F05015-28 Screw, #6-32 x 1/2” Plain PH T23 2
11 015271 Decal, Control Panel (E25/E30) 1
015269 Decal, Control Panel (Gas/Diesel) 1
12 015416 Board, LED Circuit (E25/E30) 1
015409 Board, LED Circuit (Gas/Diesel) 1
13 023147 Spacer, 1/2”-#6 Threaded 4
14 016371 Solenoid Kit, 200A 12V SPST Cont. Duty 1
015470 Solenoid, 200A 12V SPST Cont. Duty Available in assemblies only. 1
015426 Diode Assembly, Solenoid Coil Chassis 1
Gnd
15 051346 SWITCH, BLADE START/STOP 1
16 P02575 BOOT, TOGGLE SWITCH RUBBER 1
17 P05251-1 WASHER, 12 X 3/4 X 1/16 NYLON 1
069343 HARNESS ASSEMBLY, UPPER WIRING (E25 1
2010)
069307 HARNESS ASSEMBLY, UPPER WIRING (G38 1
2010)

Control & Battery Boxes WM doc 5/11/23 5-7

 Control & Battery Boxes
5 Front Panel Assembly & Harnesses

REF PART # DESCRIPTION COMMENTS QTY.

052903 Connector Assembly, Kohler Engine 1
069309 HARNESS ASSEMBLY, UPPER WIRING (D47 1
2010)
069306 HARNESS ASSEMBLY, UPPER WIRING (D51 1
2010)
050399 Conduit, 1 1/4” x 58” Flex 1
024402 Connector, 1 1/4” Straight Male Metal Conduit 1
051872 HARNESS ASSEMBLY, LOWER WIRING 1
R02374 Conduit, 1/2” Expandable Black 41 in.
R02374 Conduit, 1/2” Expandable Black 42 in.

5-8 WM doc 5/11/23 Control & Battery Boxes

 Control & Battery Boxes
Front Panel Assembly & Harnesses (US Only) 5
5.6 Front Panel Assembly & Harnesses (US Only)

8 9 2

10
4
6

7 3

3H1199-1
5

REF PART # DESCRIPTION COMMENTS QTY.

073596 PANEL ASSEMBLY, LT40 SUPER TIER 4 FRONT 1
(D35)
1 015270 Gasket, Front Panel 1
2 011298 Panel, LT40/50 Control Box Front 1
3 024450 Pot Assembly, Feed Rate Control Sawmill 1
4 P06257 Knob, Feed Rate With Set Screw 1
5 024200 Switch, Toggle 2
6 P02575 Boot, Toggle Switch Rubber 2
7 P05251-1 Washer, 1/2 x 3/4 x 1/16 Nylon 2
8 073593 Decal, Yanmar Tier 4 Control Panel Front 1
9 073601 Controller, Yanmar Tier 4 Engine 1
10 016371 SOLENOID KIT, 200A 12V SPST CONT. DUTY 1
015470 Solenoid, 200A 12V SPST Cont. Duty Available in assemblies only. 1
015426 Diode Assembly, Solenoid Coil Chassis Gnd 1
073591 HARNESS, LT40/50NR D47 UPPER 2010 1
050399 Conduit, 1 1/4” x 58” Flex 1
024402 Connector, 1 1/4” Straight Male Metal Conduit 1
051872 HARNESS ASSEMBLY, LOWER WIRING 1
R02374 Conduit, 1/2” Expandable Black 41 in.
R02374 Conduit, 1/2” Expandable Black 42 in.

Control & Battery Boxes WM doc 5/11/23 5-9

 Control & Battery Boxes
5 Battery Box Assembly

5.7 Battery Box Assembly

12
3
11
12 1

11
7
7

14
8
19
2 9
6 8
14 17 5
18 15 9
10
4
HD0598-1D 10
13
14
20
21 16

22

REF PART # DESCRIPTION COMMENTS QTY.

1 025841 BATTERY, 12 VOLT 8A31DTM AGM Available in assemblies only. 1

015565 BOX ASSEMBLY, SUPER HYDRAULIC BAT- 1

TERY
2 015191 Box Weldment, Battery 1
3 F05011-13 Washer, 5/16 Split Lock 2
4 015194 Retainer Loop, Battery 1
5 F05011-17 Washer, 5/16" SAE Flat 2
6 F05010-58 Nut, 5/16-18 Hex Nylon Lock 2
7 F05007-4 Bolt, 3/8-16 X 4" Hex Head Grade 2 2
8 F05011-3 Washer, 3/8" SAE Flat 2
9 F05011-36 Washer, 3/8" External Star 2
10 F05010-10 Nut, 3/8" Hex Nylon Lock 2
11 F05011-11 Washer, 1/4" SAE Flat 2
12 F05010-13 Nut, 1/4-20 Wing 2
13 N/A Fuse Box Parts (See Section 5.8) 1
N/A Hydraulic Positive Contact Parts (See Section 9.3) 1
14 P11764 Grommet, 5/8" Rubber Wire 4
15 074198 Grommet, 3/4" ID 11 Gauge Thickness 2
16 074199 Grommet, 3/4" ID 16 Gauge Thickness 2

5-10 WM doc 5/11/23 Control & Battery Boxes

 Control & Battery Boxes
Battery Box Assembly 5
REF PART # DESCRIPTION COMMENTS QTY.
17 052496 Plug, 1/2" Knockout Nylon 1
18 015771 LID WELDMENT, BATTERY BOX SUPER 1
19 014774 DECAL, BATTERY BOX LID CAUTION 1
20 036308 CABLE ASSEMBLY, 1 GA X 12” 150A FUSE TO 1
BATTERY POSITIVE
21 036309 CABLE ASSEMBLY, 1 GA X 16” 225A FUSE TO 1
BATTERY POSITIVE
22 036306 CABLE ASSEMBLY, 1 GA X 26” BATTERY NEG- 1
ATIVE TO NEG. CONTACT

Control & Battery Boxes WM doc 5/11/23 5-11

 Control & Battery Boxes
5 Fuse Box Assembly

5.8 Fuse Box Assembly

1
29
26 25
2 5

9 4 7
32
10
17 14 6
13
14 28 24
18
15 20 13 27
3
11
19 12
HD0598-2E
30
16
23 31

22
21
REF PART # DESCRIPTION COMMENTS QTY.
006795 BLOCK ASSEMBLY, DOUBLE FUSE 1
1 056999 Plate, Fuse Block Insulator 1
2 056997 Block, Fuse Mount Available in assemblies only. 1
3 056996 Block, 3/4” Upper Fuse 1
4 056998 Block, 3/4” Lower Fuse 2
5 F05006-20 Screw, 5/16-18 x 1/2” Socket Button Head 4
6 F05005-59 Screw, 1/4-20 x 1/2” Socket Button Head 2
7 F05005-101 Bolt, 1/4-20 x 1” Hex Head Grade 5 2
8 F05010-21 Nut, 1/4-20 Hex Lock 2
9 F05011-14 Washer, 1/4” Split Lock 3
10 F05005-123 Bolt, 1/4-20 x 3/4” Hex Head Grade 5 3
11 F05011-13 Washer, 5/16” Split Lock 4
12 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 4
13 053339 FUSE, 225A 32V MEGA 2
14 053340 FUSE, 450A 32V MEGA 2
006853 COVER ASSEMBLY, DOUBLE FUSE BOX 1
15 006851 Cover, Fuse Box 1

5-12 WM doc 5/11/23 Control & Battery Boxes

 Control & Battery Boxes
Fuse Box Assembly 5
REF PART # DESCRIPTION COMMENTS QTY.
16 F05006-2 Bolt, 5/16-18 x 1 1/2” Hex Head Full Thread 2
17 F05010-20 Nut, 5/16-18 Hex Self-Locking 4
18 F05011-17 Washer, 5/16” SAE Flat 4
19 055323 Spacer, .39” x .625” x .39” 2
20 050283 Gasket, Fuse Box Cover 1
21 F05015-7 SCREW, #10-24 X 1/2" SELF-TAPPING 4
22 P10364 DECAL, 12 VOLT WARNING 1
23 006868 DECAL, 225/450A MEGA FUSE ID 1
24 P12960 DECAL, HYDRAULIC CONTACT CAUTION 1
25 074199 GROMMET, 3/4” ID 16 GAUGE THICKNESS 2
26 016371 SOLENOID KIT, 200A 12V SPST CONT. DUTY 1
015470 Solenoid, 200A 12V SPST Cont. Duty Available in assemblies only. 1
015426 Diode Assembly, Solenoid Coil Chassis 1
Ground
024451 WIRE ASSEMBLY, HYDRAULIC SOLENOID 1
VOLTAGE DROP
27 F05005-15 BOLT, 1/4-20 X 1/2” HEX HEAD 2
28 F05011-11 WASHER, 1/4” SAE FLAT 2
29 F05010-9 NUT, 1/4-20 SELF-LOCKING HEX 2
30 036305 CABLE ASSEMBLY, 1 GA X 6 1/2” FUSE TO 1
SOLENOID
31 036307 CABLE ASSEMBLY, 1 GA X 14” SOLENOID TO 1
POSITIVE CONTACT
32 P11764 GROMMET, 5/8” ID RUBBER 1

Control & Battery Boxes WM doc 5/11/23 5-13

 Up/Down System
6 Saw Head Mount

SECTION 6 UP/DOWN SYSTEM

6.1 Saw Head Mount

13 2
3

6 7 1
4

9 5
10 8
11
10 12

SM0080D

REF PART # DESCRIPTION COMMENTS QTY.

1 W04099 V-BRACE, SAW HEAD MOUNT 1
2 F05006-5 BOLT, 5/16-18 X 3/4" HEX HEAD GRADE 5 12
F05006-93 BOLT, 5/16-18 X 1 1/4 HEX HEAD FULL THREAD 4
GRADE 5
3 M04096 PAD, PLASTIC SLIDE 6
016241 PAD, PLASTIC SLIDE LOWER W/CHAMFER 2
4 F05010-58 NUT, 5/16-18 NYLON LOCK 16
5 S07935 PLATE, V-BRACE WASHER 2
6 F05008-61 BOLT, 1/2-13 X 3 1/2" HEX HEAD GRADE 5 4
7 F05011-2 WASHER, 1/2” SAE FLAT 4
8 F05010-8 NUT, 1/2-13 NYLON LOCK 4
9 F05007-17 BOLT, 3/8-16 X 2" FULL THREAD 2
10 F05010-1 NUT, 3/8-16 HEX 4
11 F05011-3 WASHER, 3/8" SAE FLAT 2
12 F05011-4 WASHER, 3/8" SPLIT LOCK 2
13 017715 CAP, .281” X 1/2” BLACK VINYL 3

6-1 WM doc 5/11/23 Up/Down System

 Up/Down System
Blade Height & Quarter Scales 6
6.2 Blade Height & Quarter Scales

13

8
3H0961
12
7
1
10

3
4 6 5 16 18
19
STOP
1 21 17

2 20
2

5
4
9 22
6
3

8 BLADE
4
Stop
5 4

6
4

5
Start
P11779

15

13

11 21 19
20

14

REF PART # DESCRIPTION COMMENTS QTY.

K11998 Scale Kit, Fixed With Pointer Service kit 1
A12022 Scale Assembly, Fixed Available in assemblies only. 1
1 W11996 Bracket, Scale Mounting 1
2 036666 Plate, Movable Scale Stop 1
3 S11989 Scale, 35" Quarter 1
4 S11774 Decal, 35" Standard Quarter Scale 1
P12819 Decal, 35" Grade Hardwood Quarter Scale 1
5 S11988 Scale, 35" Inch 1
6 S11773 Decal, 35" Inch 1
7 S04805 Strap, Scale Hold-Down 1
8 F05012-14 Pin, 1/8" X 5/8" Roll 1
9 F05005-64 Screw, 1/4-20 X 5/8" Wing 1
10 F05005-1 Bolt, 1/4-20 x 1/2” Hex Head 2
11 F05011-11 Washer, 1/4" SAE Flat 1
12 F05011-22 Washer, 1/4" X .020 Thick Nylon Flat 2
13 F05010-9 Nut, 1/4-20 Hex Self-Locking 2

Up/Down System WM doc 5/11/23 6-2

 Up/Down System
6 Blade Height & Quarter Scales

REF PART # DESCRIPTION COMMENTS QTY.

14 F05005-70 Screw, 1/4-20 X 3/4" Flat Socket Head 1
038591 Pointer Assembly, Fixed Scale 1
15 038586 Bracket, Fixed Scale Pointer Mount 1
16 038585 Pointer, Fixed Scale 1
17 F05004-3 Screw, #10-24 X 3/8" Phillips Head 2
18 F05010-14 Nut, #10-24 Hex Self-Locking 2
19 F05005-134 Bolt, 1/4-20 x 3/4” with Conical Washer 2
20 F05011-17 Washer, 5/16” SAE Flat 2
21 F05010-6 Nut, 5/16-18 Hex Lock 2
F05005-15 Bolt, 1/4-20 X 1/2" Hex Head Grade 2 1
A12030-370 Instruction Sheet, Fixed Scale Retrofit 1
K12064 Decal Kit, Metric Scale 1
S11711 Decal, Metric 1
P12040-1 Decal, Metric 16-40mm 1
P12040-2 Decal, Metric 45-63mm 1
22 P11779 Decal, Clutch Handle Operation 1

6-3 WM doc 5/11/23 Up/Down System

 Up/Down System
Up/Down Chain & Sprockets 6
6.3 Up/Down Chain & Sprockets

1
3 2

3
4

2
1 4

5
6

3H0654-1C

8
11

10

8
9

REF PART # DESCRIPTION COMMENTS QTY.

016020 SPROCKET KIT, UP/DOWN IDLER #50-2 1
1 016019 Sprocket, Up/Down Idler ‘98 2
2 016018 Spacer, 50-2 Idler '98 4
016020-541 Instruction Sheet, Up/Down Idler Retrofit 1
3 F05009-6 BOLT, 5/8-11 X 5" HEX HEAD GRADE 2 2
4 F05010-96 NUT, 5/8-11 JAM NYLON LOCK 2
5 015259 CHAIN, #50-2 X 75.625" UP/DOWN 1
6 015258 LINK, #50-2 MASTER 2
015456 TENSIONER ASSEMBLY, UP/DOWN CHAIN 1
7 015188 Bracket, Up/Down #50 Chain Tensioner Available in assemblies only. 1
8 F05011-2 Washer, 1/2" SAE Flat 2
9 F05010-8 Nut, 1/2-13 Hex Nylon Lock 1
10 016516 Spring, 1” OD x 1” Long x .125” Wire Compr. 1
11 016515 Spacer, Up/Dn Chain Tensioner 1

Up/Down System WM doc 5/11/23 6-4

 Up/Down System
6 Up/Down Motor Assembly

6.4 Up/Down Motor Assembly

15
16 14
12
17 8 10
4 9

5 6
3 7
13
11

3H1061 1

REF PART # DESCRIPTION COMMENTS QTY.

1 - 11 008779 UP/DOWN MOTOR ASSEMBLY 1
1 053682 Motor, 1HP 12VDC Electric 1
053682-BK Brush Kit, Leeson 1HP Motor 1
2 008999 Pulley, AK32 x 5/8” 1
3 015198 Bracket, Up/Down Motor Mount 1
4 F05006-1 Bolt, 5/16-18 x 1” Hex Head 4
5 F05011-17 Washer, 5/16” SAE Flat 4
6 F05011-13 Washer, 5/16” Split Lock 4
7 F05010-17 Nut, 5/16-18 Hex 4
8 015016 Guard, Up/Down Sprocket 1
9 F05011-4 Washer, 3/8” Split Lock 2
10 F05007-27 Bolt, 3/8-16 x 3/4” Hex Head 2
11 024431 Decal, Disconnect Motor Leads Warning 1
12 038459 BELT, 4L245 NOTCHED 1
13 F05006-73 BOLT, 5/16-18 X 6” HEX HEAD GRADE 5 1
14 F05010-65 NUT, 5/16-18 HEX NYLON LOCK 1
15 015569 SPRING, .75” X 3 3/4” X .092” EXTENSION 1
16 F05011-11 WASHER, 1/4” SAE FLAT 1
17 F05010-69 NUT, 1/4-20 NYLON LOCK HEX 1

6-5 WM doc 5/11/23 Up/Down System

 Up/Down System
Up/Down Drive Assembly 6
6.5 Up/Down Drive Assembly

18
17

4 5
6 8
13 7
3
2
1 6
26
30 29
27
27 12
25
21
3H0567-2H 20
9
19 24 11
31
28
10
22 14
23
15
16
REF PART # DESCRIPTION COMMENTS QTY.
015176 UP/DOWN DRIVE ASSEMBLY 1
1 F05007-7 Bolt, 3/8-16 x 1” Hex Head 4
2 F05011-4 Washer, 3/8” Split Lock 4
3 F05011-3 Washer, 3/8” SAE Flat 8
4 014090 Bearing, Flanged Up/Down 1
016094 Shaft Kit, Up/Down Drive 1
5 016031 Shaft, Up/Down Sprocket Available in assemblies only. 1
6 F05005-105 Screw, 1/4-28 x 1/4” Socket Head Cup 3
Point
7 S04124 Key, 1/4” Square x 1 11/16” Long 1
8 074124 Gear Box, Up/Down Grove 1
9 014158 Plate, Gear Box Spacer 1
10 F05007-64 Bolt, 3/8-16 x 1” Flat Socket Head 4
11 015256 Pulley, Up/Down 1
12 S31027 Key, 3/16” Square x 1” Long 1
13 015195 Bracket, Up/Down Motor Mount 1
14 F05011-17 WASHER, 5/16" SAE FLAT 4
15 F05011-13 WASHER, 5/16” SPLIT LOCK 4
16 F05006-102 BOLT, 5/16-18 X 3/4" HEX HEAD GRADE 5 4
17 F05011-4 WASHER, 3/8” SPLIT LOCK 4
18 F05007-27 BOLT, 3/8-16 X 3/4” HEX HEAD 4
L04869-4 OIL, 8 OZ. MOBIL SHC634 BOTTLED SYN- 24 oz. required for complete oil 1
THETIC GEAR replacement.

Up/Down System WM doc 5/11/23 6-6

 Up/Down System
6 Up/Down Drive Assembly

REF PART # DESCRIPTION COMMENTS QTY.

065187 BRAKE ASSEMBLY, SUPER UP/DOWN 1
19 062511 Shaft, Up/Down Brake LT70 3/4" 1
20 062513 Plate, Brake Mount 1
21 065190 Plate, Super Up/Down Brake Mount 1
065907 Brake Assembly, LT40/50/70 Up/Down 1
Replacement
22 069519 Brake, Klauber Gearmotor #K01134D300 Available in assemblies only. 1
F05708-26 Terminal, 3/16” 18-22 Ga Quick Male 2
23 F05004-273 Bolt, #8-32 x 2” Socket Head Stainless Steel 2
24 F05005-131 Screw, 1/4-20 x 1/4” Cup Point Socket Set 2
25 F05006-15 Bolt, 5/16-18 x 1/2” Hex Head Grade 5 2
26 F05007-92 Bolt, 3/8-16 x 4” Hex Head Full Thread Grade 1
5
27 F05010-1 Nut, 3/8-16 Hex 3
28 F05010-169 Nut, #8-32 Hex Nylon Lock 2
29 F05011-3 Washer, 3/8” SAE Flat 2
30 F05011-4 Washer, 3/8” Split Lock 1
31 P10688 Bearing, R6-2NSL SRI-2 ABEC-1 1
069678-S-FR Diode OR Assembly, Up/Down Brake LT40/50 1

6-7 WM doc 5/11/23 Up/Down System

 Feed System & Track Rollers
Upper Track Rollers And Wipers 7
SECTION 7 FEED SYSTEM & TRACK ROLLERS
7.1 Upper Track Rollers And Wipers

15
18
3
6 19

10
11
5
16
2
3 15 20 17 1
4
6
1
8
4
5
7 3

1
12 3H0125F

13
9

REF PART # DESCRIPTION COMMENTS QTY.

1 012797 ROLLER, TRACK CAM BEARING 5
2 016510 SHIM, 5/8” X 1” X .062” 2
3 F05010-11 NUT, 5/8-18 HEX JAM 5
4 F05008-5 SCREW, 1/2-13 X 1 1/4” OVAL POINT SET 2
5 F05010-31 NUT, 1/2-13 HEX JAM 2
6 F05005-64 SCREW, 1/4-20 X 5/8" THUMB 4
7 M04113 WIPER, PLASTIC TRACK 2
8 012999 HOUSING, UPPER TRACK ROLLER REAR 1
9 016285 HOUSING, UPPER TRACK ROLLER FRONT 1
10 F05007-2 BOLT, 3/8-16 X 1 1/4” HEX HEAD 2
11 F05010-29 NUT, 3/8-16 HEX JAM 2
12 016501 BLOCK, UPPER ROLLER PIVOT 1
13 F05013-3 BOLT, 3/4-10 X 4” HEX HEAD GRADE 5 1
14 F05010-80 NUT, 3/4-10 SELF LOCKING 1
110612 COVER ASSEMBLY, LT40 TRACK 1
15 110609 Cover, Middle Track, LT40 Available in assemblies only. 1
16 110611 Retainer, Felt Oiler Available in assemblies only. 1
17 F05005-113 Bolt, 1/4-20x3/4 Carriage 4
18 F05010-69 Nut, 1/4-20 Nylock 4
19 F05011-11 Washer, 1/4 SAE Flat 4
20 S09915 Felt, Middle Track Oiler LT40/50/70 1

Feed System & Track Rollers WM doc 5/11/23 7-1

 Feed System & Track Rollers
7 Power Feed Assembly

7.2 Power Feed Assembly

14
27
16 24
26

25 30 33
Disconnect motor leads before
connecting any power source to
15
motor terminals. Failure to do so
may cause serious injury and will
29 28
damage the electrical system.
Wood-Mizer
800-525-8100 Reorder #024431
31 18
23
22 19
11
12
2
1 4

17
20
9 20
10
21
3 9 31
29
15 32
14
13

7
5
5 6
3H0814-1D
6

REF PART # DESCRIPTION COMMENTS QTY.

015125 POWER FEED ASSEMBLY 1
1 015126 Cover Weldment, Top Power Feed 1
2 015133 Plate, Power Feed Motor 1
3 024169 Motor, 3/4HP Power Feed Painted 1
024167 Brush Kit, Leeson 3/4HP Motor (Includes 1
2 Brushes and 2 Springs)
016087 Fan, 3/4 HP Leeson Motor Replacement 1
061146 Guard, Motor Fan Leeson 3/4HP 1
4 S31027 Key, 3/16” Square x 1” Long 1
5 F05011-11 Washer, 1/4" SAE Flat 4
6 F05005-54 Bolt, 1/4-20 X 3 1/2" Hex Head Grade 2 4
7 010748 Clamp, 5/8” EMT Coated 2
8 016088 Sheave, AK71 x 5/8” Power Feed (200ft./min.) To increase feed return rate to 1
220 ft./min. replace with AK64
sheave 016114 and AX35 belt
015175 (replaces kit 016085).
Kit 016070, AL84 x 5/8" Sheave
016115 and AX38 Belt 016068
to reduce feed return rate to 183
ft./min. no longer available.
9 F05006-32 Screw, 5/16-18 x 3/4” Cup Point Set 2

7-2 WM doc 5/11/23 Feed System & Track Rollers

 Feed System & Track Rollers
Power Feed Assembly 7
REF PART # DESCRIPTION COMMENTS QTY.
10 016083 Belt, AX36 (200ft./min.) To increase feed return rate to 1
220 ft./min. replace with AK64
sheave 016114 and AX35 belt
015175 (replaces kit 016085).
Kit 016070, AL84 x 5/8" Sheave
016115 and AX38 Belt 016068
to reduce feed return rate to 183
ft./min. no longer available.
11 015135 Sheave, 1 3/4” Feed Motor 1
12 F05007-12 Screw, 3/8”-16 x 1/2” Cup Point Set 2
13 F05007-7 Bolt, 3/8-16 x 1” Hex Head 1
14 F05011-4 Washer, 3/8" Split Lock 5
15 F05011-3 Washer, 3/8” Flat 5
16 015162 Bracket, Power Feed Mount 1
17 015132 Brace, Power Feed Mounting 1
016066 Shaft Assembly, Power Feed with Key 1
18 015129 Shaft Weldment, Power Feed Available in assemblies only. 1
19 016108 Key, 3/16” Square x 1 3/8” Long 1
20 P06030-1 Bearing, 5/8" 6203-2NSL 2
21 F05011-19 Washer, 5/8” x 15/16” x .094” Nylon 1
22 016366 Sprocket, #40/41 Idler 17T 5/8” ID w/Bearing 1
23 F05010-96 Nut, 5/8-11 Nylon Lock Jam 1
24 F05007-27 Bolt, 3/8-16 x 3/4” Hex Head 4
25 F05010-10 Nut, 3/8-16 Hex Nylon Lock 1
26 015134 Plate, Belt Tensioner 1
27 F05007-16 Bolt, 3/8-16 x 2” Full Thread Hex Head 1
28 015136 Spacer, Power Feed Motor 4
29 024431 Decal, Disconnect Motor Leads Warning 1
30 F05007-35 BOLT, 3/8-16 X 4 1/2” HEX HEAD 1
31 F05011-3 WASHER, 3/8" SAE FLAT 4
32 F05010-10 NUT, 3/8-16 HEX NYLON LOCK 2
33 F05007-4 BOLT, 3/8-16 X 4” FULL THREAD HEX HEAD 1
TAP GRADE 5

Feed System & Track Rollers WM doc 5/11/23 7-3

 Power Feed System
7 Feed Chain/Stop

7.3 Feed Chain/Stop

19 18 14
13
9
12

10

11 13
7

6
8 2
8 2
7
1 15
17
5
4
SM0353-1
3
16

REF PART # DESCRIPTION COMMENTS QTY.

1 014745 CHAIN, #40 X 267.5" LT40 FEED 1
2 P04200 LINK, #40 MASTER 2
3 015721 TENSIONER WELDMENT, POWER FEED CHAIN 1
4 F05011-2 WASHER, 1/2” SAE FLAT 3
5 F05011-9 WASHER, 1/2” SPLIT LOCK 3
6 F05008-128 BOLT, 1/2-13 X 1” HEX HEAD GRADE 8 3
7 F05010-16 NUT, 1/2-20 HEX JAM 2
8 F05011-9 WASHER, 1/2" SPLIT LOCK 2
9 006686 BRACKET WELDMENT, REAR FEED STOP 1
K09630 STOP KIT, RUBBER CARRIAGE 2
10 P12165 Stop, Rubber Carriage 1
11 W09293 Pin, Rubber Carriage Stop 1
12 F05012-21 Pin, 3/16" X 1" Cotter 1
13 F05005-134 BOLT, 1/4-20 X 3/4” WITH CONICAL WASHER 1
14 057822 PLATE, BED TUBE END W/LIGHT MOUNT 1
15 015008 BRACKET, FRONT FEED CHAIN MOUNT 1
16 F05007-87 BOLT, 3/8-16 X 1” HEX HEAD GRADE 5 2
17 F05010-10 NUT, 3/8-16 HEX NYLON LOCK 2
18 006688 GROMMET, 6 1/2” LIGHT MOUNTING 1
19 006391 LIGHT, 8 DIODE LED TAIL 1

7-4 WM doc 5/11/23 Power Feed System

 Power Feed System
Lower Track Rollers 7
7.4 Lower Track Rollers

4 5
7
10
9

6
8
4 5

5
4

3H0812B

3
11 1

REF PART # DESCRIPTION COMMENTS QTY.

012995 ROLLER ASSEMBLY, LOWER TRACK 2
1 012982 Bracket, Lower Track Roller Mounting Available in assemblies only. 1
2 012797 Roller, Track Cam Bearing 1
3 F05010-11 Nut, 5/8-18 Hex Jam 1
4 F05010-5 Nut, 5/8-11 Hex 4
5 F05011-118 Washer, 5/8" Split Lock Grade 8 4
6 033374 Bracket Weldment, Lower Track Roller Wiper 1
7 033375 Wiper, Round Gray Felt 1
8 F05008-2 BOLT, 1/2-13 X 2 1/4” HEX HEAD FULL THREAD 2
9 F05010-31 NUT, 1/2-13 HEX JAM 2
10 F05010-3 NUT, 1/2-13 HEX LOCK 2
11 F05008-61 BOLT, 1/2-13 X 3 1/2" HEX HEAD GRADE 5 2

Power Feed System WM doc 5/11/23 7-5

 Bed Frame Assembly
8 Bed Rail Assembly, Front And Rear

SECTION 8 BED FRAME ASSEMBLY

8.1 Bed Rail Assembly, Front And Rear

21

22 7 10
9
1
17
19 6

18

11 5 2
15 4
16 3

14

12
3h1177-1 20
13

REF PART # DESCRIPTION COMMENTS QTY.

003298 BED RAIL ASSEMBLY, REAR PAINTED (LT50 1
BED 4)
1 034547 Tube Weldment, Bed Rail 4 1
2 F05010-5 Nut, 5/8-11 Hex 2
3 S13006 Bolt, Bed Rail Adjustment 2
4 F05008-78 Bolt, 1/2-13 X 4" Hex Head 1
5 F05011-2 Washer, 1/2" SAE Flat 3
6 F05010-8 Nut, 1/2-13 Nylon Lock 2
7 F05008-94 Bolt, 1/2-13 x 3 1/2” Carriage 1
079144 Cover Kit, Front/Rear Bed Rail SS 1
8 016898 Cover, Stainless Steel Bed Rail 1
9 F05006-10 Bolt, 5/16-18 X 2 1/2" Hex Head 3
10 F05010-6 Nut, 5/16-18 Hex Lock 3
Hydraulic Toe Board Parts () (See Section 9.10)
034548 BED RAIL ASSEMBLY, FRONT PAINTED 1
(LT60/70 BED 1)
11 034544 Tube Weldment, Bed Rail 1 1
12 F05010-5 Nut, 5/8-11 Hex 2
13 S13006 Bolt, Bed Rail Adjustment 2
14 F05008-78 Bolt, 1/2-13 X 4" Hex Head 2
15 F05011-2 Washer, 1/2" SAE Flat 4

8-1 WM doc 5/11/23 Bed Frame Assembly

 Bed Frame Assembly
Bed Rail Assembly, Front And Rear 8
REF PART # DESCRIPTION COMMENTS QTY.
16 F05010-8 Nut, 1/2-13 Nylon Lock 2
079144 Cover Kit, Front/Rear Bed Rail SS 1
17 016898 Cover, Stainless Steel Bed Rail 1
18 F05006-10 Bolt, 5/16-18 X 2 1/2" Hex Head 3
19 F05010-6 Nut, 5/16-18 Hex Lock 3
Hydraulic Toe Board Parts () (See Section 9.10)
20 015970 WRENCH, BED RAIL ADJUSTMENT OPTIONAL 1
21 038843 CAP, BED RAIL REMOVABLE END 2
22 F05005-134 BOLT, 1/4-20 X 3/4” W/CONICAL WASHER 2
HEAD

Bed Frame Assembly WM doc 5/11/23 8-2

 Bed Frame Assembly
8 Bed Rail Assembly, Middle Front

8.2 Bed Rail Assembly, Middle Front

8
9

1
5 10
6

7
4 2 11
6
3
600510

REF PART # DESCRIPTION COMMENTS QTY.

034549 BED RAIL ASSEMBLY, FRONT MIDDLE (LT60/70 1
BED 2)
1 034545 Bed Rail Tube, Short Available in assemblies only. 1
2 F05010-5 Nut, 5/8-11 Hex 2
3 S13006 Bolt, Bed Rail Adjustment 2
4 S04058 Plate, Bed Rail End Cap Available in assemblies only. 2
5 F05008-78 Bolt, 1/2-13 X 4" Hex Head Grade 5 2
6 F05011-2 Washer, 1/2" SAE Flat 4
7 F05010-8 Nut, 1/2-13 Nylon Lock 2
A09956 Cover Assembly, Stainless Steel Bed Rail 1
(Long)
8 S09944 Cover, Stainless Steel Bed Rail Available in assemblies only. 1
9 F05006-10 Bolt, 5/16-18 X 2 1/2" Hex Head 3
10 F05010-6 Nut, 5/16-18 Hex Lock 3
11 015970 WRENCH, BED RAIL ADJUSTMENT 1

8-3 WM doc 5/11/23 Bed Frame Assembly

 Bed Frame Assembly
Bed Rail Assembly, Middle Rear 8
8.3 Bed Rail Assembly, Middle Rear

3
2
9
11

10
1

12 8

6 4

600511 5

REF PART # DESCRIPTION COMMENTS QTY.

034550 BED RAIL ASSEMBLY, REAR MIDDLE PAINTED 1
(LT60/70 BED 3)
1 034546 Tube Weldment, Bed Rail 3 1
2 F05007-2 Screw, 3/8-16x1 1/4 HHC 1
3 F05010-29 Nut, 3/8-16 Hex Jam 1
4 F05010-5 Nut, 5/8-11 Hex 2
5 S13006 Bolt, Bed Rail Adjustment 2
6 F05008-78 Bolt, 1/2-13 X 4" Hex Head Grade 5 2
7 F05011-2 Washer, 1/2" SAE Flat 4
8 F05010-8 Nut, 1/2-13 Nylon Lock 2
A09956 Cover Assembly, Stainless Steel Bed Rail 1
(Long)
9 S09944 Cover, Stainless Steel Bed Rail Available in assemblies only. 1
10 F05006-10 Bolt, 5/16-18 X 2 1/2" Hex Head 3
11 F05010-6 Nut, 5/16-18 Hex Lock 3
12 015970 WRENCH, BED RAIL ADJUSTMENT 1

Bed Frame Assembly WM doc 5/11/23 8-4

 Bed Frame Assembly
8 Fine Adjustable Legs Overview

8.4 Fine Adjustable Legs Overview

REF PART # DESCRIPTION COMMENTS QTY.

1 003944 Leg Assembly, Adj. Outrigger Front See Section 8.5 FAO Outrigger, 1
Front
2 056781 Leg Assembly, Loading Side Adjustable See Section 8.6 FAO Outrigger, 2
Loading Side
3 056787 Leg Assembly, Adj Outrigger Offset See Section 8.7 FAO Outrigger, 2
Offset Leg
4 056791 Leg Assembly, Rear Adj. Outrigger See Section 8.8 FAO Outrigger, 1
Rear
See Form #2540 for Stationary
Legs
See Form #2541 for Adjustable
Legs

8-5 WM doc 5/11/23 Bed Frame Assembly

 Replacement Parts
FAO Outrigger, Front 8
8.5 FAO Outrigger, Front

INSIDES ASSEMBLED

REF PART # DESCRIPTION COMMENTS QTY.

1 F05007-113 Bolt, 3/8-16x5 Carriage 4
2 003943 Wldmnt, Front Adj Outrigger Mount 1
3 059577 Bracket, Adjustable Outrigger Lock 1
4 F05011-2 Washer, 1/2 SAE Flat 4
5 F05010-10 Nut, 3/8-16 Hex Nyl Lock 4
6 F05012-162 Pin, Locking Wire 1/8dia x 2-13/16 1
7 056774 Nut, Adjustable Outrigger Hex 1
8 F05012-127 Pin, 5/16x1 1/4 Roll 1
9 F05011-62 Washer, 3/4 SAE Flat 1
10 039641 Seal, Outrigger Acme Screw 1
039639 Assy, Adj. Outrigger Thrust Bearing 1
11 039637 Bearing, Needle-Roller Thrust 1
12 039638 Washer, Thrust Bearing 2
13 039645 Sleeve, Outrigger Screw 1
14 003981 Tube, 3x3x15 1/4 Outrigger Guide 1
15 039636 Nut, Adj. Outrigger Long Acme 1
16 P05060 Fitting, 1/4-28 Grease 1
17 039642 Screw, 1-5 ACME Adj. Outrigger Long 1
18 056783 Wldmnt, Adjustable Outrigger Base 1
19 056817 Pin, Adj Outrigger Locking 1

Replacement Parts WM doc 5/11/23 8-6

 Replacement Parts
8 FAO Outrigger, Loading Side

8.6 FAO Outrigger, Loading Side

REF PART # DESCRIPTION COMMENTS QTY.

1 F05007-2 Bolt, 3/8-16x1 1/4 HH Gr2 4
2 056780 Wldmnt, Loading Side Adj Outrigger Mnt 1
3 059577 Bracket, Adjustable Outrigger Lock 1
4 056826 Nut, Loading Side Adj Outrigger Mnt 4
5 F05012-162 Pin, Locking Wire 1/8dia x 2-13/16 1
6 056774 Nut, Adjustable Outrigger Hex 1
7 F05012-127 Pin, 5/16x1 1/4 Roll 1
8 F05011-62 Washer, 3/4 SAE Flat 1
9 039641 Seal, Outrigger Acme Screw 1
039639 Assy, Adj. Outrigger Thrust Bearing 1
10 039637 Bearing, Needle-Roller Thrust 1
11 039638 Washer, Thrust Bearing 2
12 039645 Sleeve, Outrigger Screw 1
13 039642 Screw, 1-5 ACME Adj. Outrigger Long 1
14 003981 Tube, 3x3x15 1/4 Outrigger Guide 1
15 P05060 Fitting, 1/4-28 Grease 1
16 039636 Nut, Adj. Outrigger Long Acme 1
17 056817 Pin, Adj Outrigger Locking 1
18 056783 Wldmnt, Adjustable Outrigger Base 1

8-7 WM doc 5/11/23 Replacement Parts

 Replacement Parts
FAO Outrigger, Offset Leg 8
8.7 FAO Outrigger, Offset Leg

REF PART # DESCRIPTION COMMENTS QTY.

1 F05007-113 Bolt, 3/8-16x5 Carriage 4
2 003943 Wldmnt, Front Adj Outrigger Mount 1
3 059577 Bracket, Adjustable Outrigger Lock 1
4 F05011-2 Washer, 1/2 SAE Flat 4
5 F05010-10 Nut, 3/8-16 Hex Nyl Lock 4
6 F05012-162 Pin, Locking Wire 1/8dia x 2-13/16 1
7 056774 Nut, Adjustable Outrigger Hex 1
8 F05012-127 Pin, 5/16x1 1/4 Roll 1
9 039645 Sleeve, Outrigger Screw 1
10 F05011-62 Washer, 3/4 SAE Flat 1
11 039641 Seal, Outrigger Acme Screw 1
039639 Assy, Adj. Outrigger Thrust Bearing 1
12 039637 Bearing, Needle-Roller Thrust 1
13 039638 Washer, Thrust Bearing 2
14 003981 Tube, 3x3x15 1/4 Outrigger Guide 1
15 039636 Nut, Adj. Outrigger Long Acme 1
16 P05060 Fitting, 1/4-28 Grease 1
17 039642 Screw, 1-5 ACME Adj. Outrigger Long 1
18 056783 Wldmnt, Adjustable Outrigger Base 1
19 056817 Pin, Adj Outrigger Locking 1

Replacement Parts WM doc 5/11/23 8-8

 Replacement Parts
8 FAO Outrigger, Rear

8.8 FAO Outrigger, Rear

REF PART # DESCRIPTION COMMENTS QTY.

1 F05007-11 Bolt, 3/8-16x1 1/4 Carriage 4
2 056815 Wldmnt, Rear Adj Outrigger Mount 1
3 F05011-3 Washer, 3/8 Flat SAE 4
4 F05010-10 Nut, 3/8-16 Hex Nyl Lock 4
5 F05012-127 Pin, 5/16x1 1/4 Roll 1
6 056774 Nut, Adjustable Outrigger Hex 1
7 F05011-62 Washer, 3/4 SAE Flat 1
8 039641 Seal, Outrigger Acme Screw 1
039639 Assy, Adj. Outrigger Thrust Bearing 1
9 039638 Washer, Thrust Bearing 2
10 039637 Bearing, Needle-Roller Thrust 1
11 039645 Sleeve, Outrigger Screw 1
12 056818 Screw, 1-5 ACME Adj. Outrigger Short 1
13 056817 Pin, Adj Outrigger Locking 1
14 F05012-162 Pin, Locking Wire 1/8dia x 2-13/16 1
15 110560 Nut, FAO Outrigger Lock 1
16 059577 Bracket, Adjustable Outrigger Lock 1
17 F05011-4 Washer, 3/8 Split Lock 1
18 F05007-118 Bolt, 3/8-16x3/4 HH Gr5 1
19 056816 Leg Wldmnt, Rear Outrigger Adj 1
20 P05060 Fitting, 1/4-28 Grease 1
21 056823 Nut, Adj Outrigger Short ACME 1
22 056795 Tube, Rear Adj Outrigger Guide 1

8-9 WM doc 5/11/23 Replacement Parts

 Bed Frame Assembly
Board Return Table Assembly 8
8.9 Board Return Table Assembly

SM0330
11
STOP!
Never use the board
return table as a
platform to stand on.

Serious injury may

result.
Wood-Miz er Products, Inc .
800-525-8100 Reorder #016077

4
To Avoid Injury:

12 Keep all persons out of

the path of returning
boards.

Failure to do so will
result in serious injury.
Wood-M izer Products, Inc.
800- 525-8100 Reorder 015365

2 4
9
8
10
1

5
6 7
8
10
5
6
9

3 9
8

REF PART # DESCRIPTION COMMENTS QTY.

003264 TABLE ASSEMBLY, BOARD RETURN 1
003270 TABLE ASSEMBLY, BOARD RETURN () 1
1 055515 Table Weldment, Board Return 1
2 003259 Cover, Board Return Table 1
3 055533 Mount Weldment, Board Return Table 1
038992 Mount Weldment, Board Return Table () 1
4 F05006-9 Bolt, 5/16-18 x 1” Carriage Head 8
5 F05011-17 Washer, 5/16” SAE Flat 8
6 F05010-58 Nut, 5/16-18 Nylon Lock 8
7 003207 Bolt, 3/8-16 x 4” x 5” ‘U’ 2
8 F05011-3 Washer, 3/8” SAE Flat 10
9 F05010-10 Nut, 3/8-16 Hex Nylon Lock 7
10 F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 3
11 016077 Decal, Board Return Table Warning 1
12 015365 Decal, Board Return Danger 1

Bed Frame Assembly WM doc 5/11/23 8-10

 Bed Frame Assembly
8 Pivot Bed Rail Assembly

8.10 Pivot Bed Rail Assembly

16
16 15
17

17
12
5
1

2 9 11
3
8 12
10
12
4
3H0128C 7
6 1413

REF PART # DESCRIPTION COMMENTS QTY.

A13015 PIVOT BED RAIL ASSEMBLY ()
012993 PIVOT BED RAIL ASSEMBLY () 2
1 W13014 Pivot Bed Rail Weldment () Available in assemblies only. 1
012992 Pivot Bed Rail Weldment () Available in assemblies only. 1
2 F05010-84 Nut, 5/8-11 Pilot Weld 2
3 F05010-5 Nut, 5/8-11 Hex 2
4 S13006 Bolt, Bed Rail Adjustment 2
5 W13090 Bracket, Pivot Rail Mounting 1
6 F05008-50 Bolt, 1/2-13 x 1” Hex Head Grade 2 1
7 F05011-52 Washer, 9/16” SAE Flat 1
8 S13016 Nut, Pivot Rail Adjustment 1
9 F05005-42 Screw, 1/4-28 x 1/4” Brass Tip Set 2
10 P04107 Fitting, 3/16” Grease 1
11 F05007-114 BOLT, 3/8-16 X 4 3/4” CARRIAGE HEAD 2
12 F05007-113 BOLT, 3/8-16 X 5” CARRIAGE HEAD 6
13 F05011-3 WASHER, 3/8” SAE FLAT 8
14 F05010-10 NUT, 3/8-16 NYLON LOCK 8
017710 COVER KIT, PIVOT RAIL STAINLESS STEEL () 2
015926 COVER KIT, PIVOT RAIL STAINLESS STEEL () 2
15 S13012 Cover, Stainless Steel Pivot Bed Rail () 1
012994 Cover, Stainless Steel Pivot Bed Rail () 1
16 F05006-10 Bolt, 5/16-18 X 2 1/2" Hex Head 2
17 F05010-6 Nut, 5/16-18 Hex Lock 2
015970 WRENCH, BED RAIL ADJUSTMENT (See Section 8.1) 1

8-11 WM doc 5/11/23 Bed Frame Assembly

 Bed Frame Assembly
Safety Chain Assembly 8
8.11 Safety Chain Assembly

4
2

3
1

SM0129B

REF PART # DESCRIPTION COMMENTS QTY.

1 107972 CHAIN, 15 INCH SAFETY 1
2 F05008-33 BOLT, 1/2-13X1 1/2 HEX HEAD GRADE 5 1
3 F05010-8 NUT, 1/2-13 NYLON HEX LOCK 1
4 F05011-35 WASHER, 7/16 STANDARD FLAT 1

Bed Frame Assembly WM doc 5/11/23 8-12

 Bed Frame Assembly
8 Saw Head Rest Pin Assembly

8.12 Saw Head Rest Pin Assembly

REF PART # DESCRIPTION COMMENTS QTY.

079485 Pin Assy, Rest, 40/50
079511 Pin Assy, Rest, 40/50 Hyd Wide
1 014102 Pin Weldment, C-Frame Rest 96 Hyd 1
079510 Pin Wldmt, Rest, 40/50 Hyd Wide 1
2 014151 Pin, 3/8x2 1/4 Sq Wire Lock 1
3 F05008-74 Bolt, 1/2-13 x 2 1/2” Hex Head Grade 5 F05008-74 was F05008-10; two 1
washers added after 5/14/2021,
ECN 37840.
4 F05011-2 Washer, 1/2 SAE Flat 4
5 F05010-3 Nut, 1/2-13 Swaged Hex 1

8-13 WM doc 5/11/23 Bed Frame Assembly

 Bed Frame Assembly
Bed Frame Decals 8
8.13 Bed Frame Decals

9
8 8

5 3
6

1 3 4 5
2
HD0118-4B

REF PART # DESCRIPTION COMMENTS QTY.

1 065034 DECAL, WHITE WOOD-MIZER EURO LOGO 1
2 065035 DECAL, HYDRAULIC EURO LOGO BLACK STD. 1
3 P07453 DECAL, AMBER REFLECTIVE 2” ROUND 2
4 S09851 DECAL, KEEP AWAY DANGER 1
5 P07452 DECAL, RED REFLECTIVE 2” ROUND 3
6 P10287 DECAL, PINCH POINT DANGER 1
7 S12581 DECAL, SAW HEAD REST CAUTION 1
8 S12051 DECAL, LOG LIMIT STRIPE 2
9 P12961 DECAL, KEEP AWAY HYDRAULIC WARNING 1

Bed Frame Assembly WM doc 5/11/23 8-14

 Bed Frame Assembly
8 Board Outfeed Table (Optional)

8.14 Board Outfeed Table (Optional)

10

10
11
8
9 2
7 1
6 11
10
3 8
9
5 7
6
4
3

SM0316 4

REF PART # DESCRIPTION COMMENTS QTY.

016652 TABLE ASSEMBLY, BOARD OUTFEED 1
1 016606 Table Weldment, Board Outfeed 1
2 038167 Roller, 2 1/2” x 25” 6
3 016609 Mount Weldment, Outfeed Table Leg 2
4 016651 Leg Weldment, Outfeed Table 4
5 014151 Pin, 3/8” x 2 1/4” Square Wire Lock 4
6 016677 Pin, Snap - Coil Tension 4
7 F05004-123 Bolt, 3/8-16x3 1/2 HH Gr5 4
8 F05010-222 Nut, 3/8-16 Flanged Hex Nylock 4
9 F05011-3 Washer, 3/8 Flat SAE 4
10 S12641 Decal, Hand Pinch Point Warning 4
11 015882 Decal, Wood-Mizer Logo 10.25" 2

8-15 WM doc 5/11/23 Bed Frame Assembly

 Bed Hydraulic System
Hydraulic Hoses 9
SECTION 9 BED HYDRAULIC SYSTEM
9.1 Hydraulic Hoses

ID Color LENGTH Application (NOTE: See Hydraulic Information Section in Oper- PART #
Code "A" ator’s Manual for Hydraulic Schematics)
H1 Purple 219” 1/4” Rear Toe Board Top 079000-219
H2 Black 219” 1/4” Rear Toe Board Base 079000-219
H3 Yellow 117” 1/4” Front Toe Board Top 079000-117
H4 Gray 117” 1/4” Front Toe Board Base 079000-117
H5 Green 204” 1/4” Clamp Up/Down Top 079000-204
H6 Yellow 193” 1/4” Clamp Up/Down Base 079000-194
H7 Red 178” 3/8” Loading Arm Base 079001-178
H8 Blue 178” 3/8” Loading Arm Top 079001-178
H9 Orange 65” 3/8” Side Support Base 079001-65
H10 Plain 73” 3/8” Side Support Top 079001-73
H11 Orange 177” 3/8” Clamp In/Out Base 079001-177
H12 White 151” 3/8” Clamp In/Out Top 079001-151
H13 Green 38” 3/8” Loading Arm Branch Top 079001-38
H14 Green 77” 3/8” Loading Arm Branch Top 079001-77
H15 Yellow 81” 3/8” Loading Arm Branch Base 079001-81
H16 Yellow 43” 3/8” Loading Arm Branch Base 079001-43
H17 Plain 181” 3/8” Log Turner Base 079001-181
H18 Pink 181” 3/8” Log Turner Top 079001-181
H19 Purple 177” 3/8” Log Turner Motor (Nearest Frame) 079001-177
H20 Black 180” 3/8” Log Turner Motor (Furthest from Frame) 079001-180
H21 Plain 15” 1/4” Pump To Valve (two hoses) 057964
H22 Plain 6 1/2” 3/8” Gauge To Valve 079001-6.5

Bed Hydraulic System WM doc 5/11/23 9-1

 Bed Hydraulic System
9 Hydraulic Control Box

9.2 Hydraulic Control Box

53

45
44

25
26 26
25
24 24
23
8
9 9 21
9 23 21
6
11 3
10 3 3 5
7
34 40
4 35 39
3
3 4
4 36
12 37
38
2 57
13 58 56
20 39
39
60 1 41 42
59 43 40
19
20 44
17 47
51 52
49
18
46
48 44
600013F 55 16 50
61 50
46 44
14
62
29 45
63 27
54
15 26 31
64 28
30
32
65

22 34
35
36

REF PART # DESCRIPTION COMMENTS QTY.

017649 BOX ASSEMBLY, HYDRAULIC CONTROL 1
1 034383 Box Weldment, Hydraulic Control 1
034533 Valve Assembly, 7-Section Hydraulic 1
2 034451 Valve, 7-Section Hydraulic 1
3 014687 Fitting, 3/8” O-Ring x 3/8” JIC 8
4 P26284 Fitting, 1/4” JIC x 3/8” O-Ring 3
5 014686 Fitting, #6 SAE x 1/4” NPT Female 1
6 014685 Fitting, 1/4” NPT x 3/8” Hose Barb 1
7 P12739 Clamp, 11/16” Hose 1
8 015489 Fitting, #6 SAE 45° Elbow 1
9 015488 Fitting, #4 SAE x #6 SAE 45° Elbow 3
10 F05007-7 Bolt, 3/8-16 x 1” Hex Head 2

9-2 WM doc 5/11/23 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Control Box 9
REF PART # DESCRIPTION COMMENTS QTY.
11 F05010-10 Nut, 3/8-16 Hex Nylon Lock 2
12 024198 Switch, Hydraulic Valve Lever 1
13 F05004-13 Screw, #4-40 x 3/4” Slotted Head 2
14 034202 Seal, 7-Handle Valve Rubber 1
15 033999 Plate, 7-Handle Decal 1
16 F05015-7 Screw, #10-24 x 1/2” Self-Tapping 8
17 F05011-18 Washer, #10 SAE Flat 2
18 F05010-14 Nut, #10-24 Hex Self-Locking 2
19 F05010-10 Nut, 3/8-16 Hex Nylon Lock 4
20 F05007-113 Bolt, 3/8-16 x 5” Carriage Head 4
034534 Pump Assembly, LT60/70 DC Hydraulic 1
21 061764 Pump Kit, Hydraulic w/Motor 2
016199 Pump, Hydraulic Replacement Mon- 1
arch Model #12070
052807 Motor Kit, Hydraulic Replacement 1
038683 Motor, 12 VDC Hydraulic Pump Available in assemblies only. 1
#08714 (Iskra)
038682 Brush Kit, 4-Valve 1
Hydraulic Pump Motor
#08658-I (Iskra)
P12513 Bearing, Base Motor 1
#02318
22 052806 Wire Assembly, Motor Brush 1
Ground
P12817 Cap, Hydraulic Pump Vented Fill 1
#03171
P10198 O-Ring, Hydraulic Pump/Reservoir 1
#02352
P10315 Seal, Hydraulic Pump/Motor #02330 1
23 015490 Fitting, 3/8” NPT x 1/4” NPT Reducer 2
24 P09142 Fitting, 1/4” NPT x 1/4” JIC Elbow 2
25 P12708 Fitting, 3/8” NPT x 3/8” Hose Barb Elbow 2
26 P12739 Clamp, 11/16” Hose 4
27 015995 Fitting, 1/2” NPT x 1/2” NPT Adapter 1
28 015997 Fitting, 1/2” NPT x 1/2” Hose Barb Elbow 1
29 016795 Fitting, 1/2” NPT Close Brass Nipple 1
30 016793 Fitting, 1/2” NPT Female Tee 1
31 016794 Fitting, 1/2” NPT Male x 1/2” Hose Barb 1
32 P26258 Fitting, 1/2” NPT Pipe Plug 1
33 015992 Guard, Crossover Hose 1
34 F05011-3 Washer, 3/8” SAE Flat 8
35 F05011-4 Washer, 3/8” Split Lock 8
36 F05007-7 Bolt, 3/8-16 x 1” Hex Head 8
37 P22683 Manifold, Hydraulic Filter w/Cartridge 1
38 P20301 Filter, S28 Hydraulic Cartridge 1
39 P12707 Fitting, 1/2” NPT x 3/8” Hose Barb Elbow 2
40 P12739 Clamp, 11/16” Hose Clamp 2
41 F05011-14 Washer, 1/4” Split Lock 2
42 F05005-15 Bolt, 1/4-20 x 1/2” Hex Head 2
43 015485 Fitting, 3/8” Hose Barb Tee 1
44 F05011-3 Washer, 3/8” SAE Flat 6

Bed Hydraulic System WM doc 5/11/23 9-3

 Bed Hydraulic System
9 Hydraulic Control Box

REF PART # DESCRIPTION COMMENTS QTY.

45 F05007-87 Bolt, 3/8-16 x 1” Hex Head Grade 5 4
46 F05007-2 Bolt, 3/8-16 x 1 1/4” Hex Head 2
47 016371 Solenoid Kit, 200A 12V SPST Hydraulic Motor 2
015470 Solenoid, 200A 12V SPST Cont. Duty Available in assemblies only. 1
015426 Diode Assembly, Solenoid Coil Chassis 1
Gnd
48 F05011-37 Washer, 1/4” External Lock 4
49 F05010-9 Nut, 1/4-20 Hex Self-Locking 4
50 F05005-1 Bolt, 1/4-20 x 3/4” Hex Head Full Thread 4
51 F05011-11 Washer, 1/4” SAE Flat 4
52 015227 Plate, Hydraulic Control Box Side 1
53 015228 Plate, Hydraulic Control Box Top 1
54 P04137 Grommet, 5/8” Wire 2
55 017669 Decal, Hydraulic Control Lever 1
56 P22311 Fitting, 1/4” NPT Cross 1
57 P05498 Plug, 1/4” NPT Pipe 1
58 015491 Fitting, 3/8” JIC x 1/4” NPT Elbow 1
59 P09142 Fitting, 1/4” NPT x 1/4” JIC Male Elbow 1
60 P09143 Fitting, 1/4” NPT x 1/4” JIC Male 1
036303 Hose, 3/8” x 6 1/2” Hydraulic w/Fittings 1
036292 Hose, 1/4” x 15” Hydraulic w/Fittings 2
61 036315 WIRE ASSEMBLY, 14 GA X 4” #10 & 5/16” RING
TERMINALS
62 036314 WIRE ASSEMBLY, 14 GA X 4” #10 RING TERMI- 1
NALS
63 036311 CABLE ASSEMBLY, 1 GA X 6” HYDRAULIC 1
PUMP TO SOLENOID
64 036310 CABLE ASSEMBLY, 1 GA X 16” HYDRAULIC 1
PUMP TO SOLENOID
65 036312 CABLE ASSEMBLY, 1 GA X 16” HYDRAULIC 2
PUMP GROUND
F05011-36 WASHER, 3/8” STAR EXTERNAL 3

9-4 WM doc 5/11/23 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Power Supply Strip 9
9.3 Hydraulic Power Supply Strip

REF PART # DESCRIPTION COMMENTS QTY.

015564 STRIP ASSEMBLY, SUPER CONTACT 1
1 F05010-86 Nut, 5/16-18 Nyl Lock Hex 1
2 P11976 Housing, Contact Strip 1
3 S10075 Strip, 1/8x1x69 13/16 CU 1
4 F05015-1 Bolt, 1/4-20x1/2 Sl HH 8
5 F05006-45 Bolt, 5/16-18x3/4 HH Moulded Blk 1
052161 Cable Assembly, 1AWG 2
6 R01971 Cable, 1AWG SO Welding, Black 1
7 F05092-16 Terminal, 5/16 1-2Ga Ring NI Loose 2
8 P04137 Grommet, 5/8 Wire 2
R01950-8 Tubing, 3/4 Heat Shrink W/Adhesive ID Not Shown .33ft
016797 GROUND ASSY, FLOATING CONTACT 1
9 F05007-175 Bolt, 3/8-16x4 Square Head 2
10 015264 Block, Exten. Hyd Ground Contact 1
11 F05010-17 Nut, 5/16-18 Hex 2
12 P10077 Spring, .42x.59x.042 Comp 4
13 F05011-17 Washer, 5/16 SAE Flat 2

Bed Hydraulic System WM doc 5/11/23 9-5

 Bed Hydraulic System
9 Hydraulic Power Supply Strip

REF PART # DESCRIPTION COMMENTS QTY.

14 F05006-93 Bolt, 5/16-18x1-1/4 HH FT Gr5 2
15 016792 Plate, HPS Ground Contact Mount 1
16 F05011-3 Washer, 3/8 Flat SAE 2
17 F05010-10 Nut, 3/8-16 Hex Nyl Lock 4
017671 CONTACT ASSY, POSITIVE HYD POWER (97+) 1
18 F05005-38 Screw, 1/4-20x1 HHC 2
19 F05011-11 Washer, 1/4 SAE Flat 2
20 F05006-20 Screw, 5/16-18x1/2 SBH 1
21 F05007-11 Bolt, 3/8-16x1 1/4 Carriage 2
22 S10072 Plate, 1/2 Nyl Insulator Contact 1
23 F05010-9 Nut, 1/4-20 Keps 2
24 F05006-143 Bolt, 5/16x3/4 Shoulder (1/4-20 Thread) 2
25 015253 Button, Hot Contact 1997 1
26 015324 Plate Wdmt, Hot Contact 1
27 015564 Strip Assy, Super Contact 1

9-6 WM doc 5/11/23 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Log Loader 9
9.4 Hydraulic Log Loader

26
21 28 29
20 25
24
19
27

3 4

2 1
6
5

15
8
13
17
16 18
22
14
12 23
7 9
10

11
12
600128-1G

REF PART # DESCRIPTION COMMENTS QTY.

034539 LOADER ASSEMBLY, HYDRAULIC LOG 1
036416 Arm Assembly, Hydraulic Log Loading 1
1 110372 Arm Weldment, Log Loading 1
2 P04107 Fitting, 3/16" Grease 2
3 110472 Chain, 12-1/2 Inch Safety 1
4 F05008-146 Bolt, 1/2 x 1 Shoulder Socket 1
5 F05010-10 Nut, 3/8-16 Hex Nyloc 1
6 F05011-3 Washer, 3/8 Flat SAE 1
7 W09444 Channel, Hydraulic Log Loading Foot 2
8 P04107 Fitting, 3/16" Grease 4
038735 Cylinder Assembly, Hydraulic Log Loader 2
9 042754 Cylinder, 8" X 3" Hydraulic (3/8” NPT 1
Ports)
P12956 Seal Kit, 8" x 3" Hydraulic Cylinder 1
10 016819 Fitting, 3/8” NPT x 3/8” JIC Male Connec- 1
tor
11 042756 Fitting, 3/8” JIC 90° Swivel Elbow 1
12 038734 Fitting, 3/8NPT 6.5GPM Velocity Fuse 1
13 W09446 Pin, Loading Arm Mount 4
14 F05005-1 Bolt, 1/4-20 x 3/4” Hex Head Full Thread 4

Bed Hydraulic System WM doc 5/11/23 9-7

 Bed Hydraulic System
9 Hydraulic Log Loader

REF PART # DESCRIPTION COMMENTS QTY.

15 F05010-69 Nut, 1/4-20 Hex Lock 4
16 S09251 Pin, Loading Arm Cylinder Mount 2
17 F05011-28 Washer, 1" SAE Flat 4
18 F05012-23 Pin, 3/16" X 1 1/2" Cotter 4
19 015487 Fitting, 3/8” JIC Union ‘T’ 1
20 016041 Clamp, 3/8” Hydraulic Hose 6
21 F05006-102 Bolt, 5/16-18 X 3/4" Hex Head Grade 5 6
22 F05008-7 BOLT, 1/2-13 X 3” HEX HEAD FULL THREAD 2
GRADE 5
23 F05010-31 NUT, 1/2-13 JAM 2
074208 ARM LOCK ASSEMBLY, LT70 WIDE LOADING 1
(LT70 WIDE HEAD ONLY)
24 036692 Pin Weldment, Arm Support 1
25 F05005-101 Bolt, 1/4-20 x 1” Hex Head Grade 5 1
26 F05010-69 Nut, 1/4-20 Nylock 1
27 017604 Pin, Lynch 3/16” w/Chain 1
28 F05011-11 Washer, 1/4” SAE Flat 2
29 016090 Cable, 3/32” Dia. Board Return 1
074207 LINK, 1/2” THEADED CHAIN QUICK (LT70 WIDE 1
HEAD ONLY)

9-8 WM doc 5/11/23 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Log Turner 9
9.5 Hydraulic Log Turner

5 3

7
27

6
8

26
9
25
1 4 19
15 16 15
17
21
10 28 18
14
12
29

11
10 21
13 23
600279B
24
20
22

REF PART # DESCRIPTION COMMENTS QTY.

006095 ARM ASSEMBLY, HYDRAULIC LOG TURNER 1
1 006471 Arm Weldment, Hydraulic Log Turner 1
2 007331 Motor, Hydraulic Log Turner 1
061427 Kit, Seal Rebuild 1
3 F05008-23 Bolt, 1/2-13 x 3” Hex Head Grade 5 4
4 F05010-3 Nut, 1/2-13 Hex Lock 4
5 042192 Sprocket Weldment, Log Turner Drive 1
6 018741-2 Nut, Hydraulic Motor Castle 1
7 F05012-43 Pin, 1/8” x 1 3/4” Cotter 1
8 006097 Chain Weldment, Log Turner 1
9 016796 Link, #2080H Master 1
10 F05004-132 Bolt, 1-8 x 5” Hex Head Grade 8 2
042193 Sprocket Assembly, Idler 1
11 042191 Sprocket Weldment, Idler 1
12 P11035 Bearing, 6206 25 Idler 2
13 F04254-12 Ring, 62mm #472 DIN Inside Retaining 1

Bed Hydraulic System WM doc 5/11/23 9-9

 Bed Hydraulic System
9 Hydraulic Log Turner

REF PART # DESCRIPTION COMMENTS QTY.

14 042187 Spacer, Idler Sprocket 2
15 F05010-109 Nut, 1-8 Hex Lock 2
16 038749 Washer, 1” ID x 2” OD x 1/4” 1
17 042188 Plate, Log Turner Chain Tensioner 1
18 F05009-31 Bolt, 5/8-11 x 4” Hex Head Full Thread Grade 1
5
19 F05010-82 Nut, 5/8-11 Hex Jam 1
20 128113 Cylinder, 2” x 10” Welded Rod End Hydraulic 128113 replaced 034267 per 1
ECN 37500 on 6/24/2020. Cyl-
inder mayhave a vendor # of
either 322009 or 322896. The
322009 uses seal kit # 061364;
322896 uses seal kit # 128258.
21 016820 Fitting, 3/8” NPT x 3/8” JIC 90° Elbow 2
22 S09251 Pin, 1” x 3.88” 1
23 F05012-23 Pin, 3/16” x 1 1/2” Cotter 2
24 F05011-28 Washer, 1” SAE Flat 2
25 006722 Rod, Grooved Turner Mount 1
26 P05060 Fitting, 1/4-28 Grease 1
27 017640 Fitting, #10 SAE x 3/8” JIC Straight 2
28 F05009-16 BOLT, 5/8-18 X 3 1/2” HEX HEAD BOLT FULL 1
THREAD
29 F05010-50 NUT, 5/8-18 HEX 1

9-10 WM doc 5/11/23 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Log Side Supports (Front) 9
9.6 Hydraulic Log Side Supports (Front)

4 3

6
7

5
9
8 600019-4C

9
4
3
12 14
10 13
12

13 11
11 10
15

26 27
30
31
17

28
23
22 25
17
2 25 35 36
18 19 34 37 24
25 33
21 20 32
32
16 24 29 33
38 35

36 34 36

REF PART # DESCRIPTION COMMENTS QTY.

034732 SUPPORT ASSEMBLY, VERTICAL HYDRAULIC 1
SIDE
1 034704 Rod Weldment, Vertical Side Support 1
2 P04107 Fitting, 3/16” Straight Grease 1
3 F04254-12 Ring, 62mm Din #472 Inside Retaining 2
4 042262 Bushing, Side Support 2
5 034703 Mount Weldment, Vertical Side Support 1
6 F05008-78 Bolt, 1/2-13 x 4” Hex Head Grade 5 1
7 F05008-23 Bolt, 1/2-13 x 3” Hex Head Grade 5 1
8 F05010-8 Nut, 1/2-13 Hex Nylon Lock 2
9 F05010-118 Nut, 1-14 Hex Jam 3
034733 Roller Kit, Side Support 1
10 016561 Roller, Side Support 2
11 016560 Bushing, 5/8” x 1” x 3/4” Bronze 2

Bed Hydraulic System WM doc 5/11/23 9-11

 Bed Hydraulic System
9 Hydraulic Log Side Supports (Front)

REF PART # DESCRIPTION COMMENTS QTY.

12 F05011-5 Washer, 5/8” SAE Flat 2
13 P05035 Collar, 5/8” Lock 2
14 F05009-10 Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 1
15 F05010-4 Nut, 5/8-11 Hex Lock 1
16 106880 PIN WELDMENT, 6-5/16” PIVOT 1
036053 Pin Assembly, Side Support Pivot 1
17 F04254-15 Ring, 1” 3100-100 Outside Retaining 2
18 034718 Pin, Grooved Pivot Available in assemblies only. 1
19 P04107 Fitting, 3/16” Straight Grease 1
20 034711 PUSHER WELDMENT, LOWER SIDE SUPPORT 1
21 F05011-52 WASHER, 9/16” SAE FLAT 1
22 F05011-9 WASHER, 1/2” SPLIT LOCK 1
23 F05008-50 BOLT, 1/2-13 X 1” HEX HEAD 1
24 F05008-37 BOLT, 1/2”-13 X 1 1/4” HEX HEAD GRADE 5 2
25 F05010-8 NUT, 1/2-13 HEX NYLON LOCK 3
26 106868 ARM WELDMENT, SIDE SUPPORT FRONT LIFT 1

27 P04107 FITTING, 3/16” STRAIGHT GREASE 2

28 034728 PIN WELDMENT, 10 7/8” PIVOT 1
29 F05008-23 BOLT, 1/2-13 X 3” HEX HEAD GRADE 5 1
30 034736 CYLINDER, 2 1/2” X 6” X 1/4” NPT PORT 1
HYDRAULIC
31 034726 PIN WELDMENT, 4 3/8” PIVOT 1
32 P09140 Fitting, 1/4” NPT Male Pipe Elbow 2
33 015490 Fitting, 3/8” NPT x 1/4” NPT Reducer 2
34 015484 valve, Side Support Sequence 2
35 016822 Fitting, 3/8” NPT Male Run Tee 2
36 016820 Fitting, 3/8” NpT x 3/8” JIC Elbow 3
37 016819 Fitting, 3/8” NPT x 3/8” JIC Connector 1
38 P05759 Fitting, 3/8” NPT Street Elbow 1

9-12 WM doc 5/11/23 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Log Side Supports (Rear) 9
9.7 Hydraulic Log Side Supports (Rear)

4
3
6
7

5 9

8
9
4
3
11 12
10 11 13
15 14
13 10
12

600019-2B

1 24
16
26
27
18
23
22 25
28
2
17 25
18 19 29
21
20

REF PART # DESCRIPTION COMMENTS QTY.

034732 SUPPORT ASSEMBLY, VERTICAL HYDRAULIC 1
SIDE
1 034704 Rod Weldment, Vertical Side Support 1
2 P04107 Fitting, 3/16” Straight Grease 1
3 F04254-12 Ring, 62mm Din #472 Inside Retaining 2
4 042262 Bushing, Side Support 2
5 034703 Mount Weldment, Vertical Side Support 1
6 F05008-78 Bolt, 1/2-13 x 4” Hex Head Grade 5 1
7 F05008-23 Bolt, 1/2-13 x 3” Hex Head Grade 5 1
8 F05010-8 Nut, 1/2-13 Hex Nylon Lock 2
9 F05010-118 Nut, 1-14 Hex Jam 3
034733 Roller Kit, Side Support 1
10 016561 Roller, Side Support 2
11 016560 Bushing, 5/8” x 1” x 3/4” Bronze 2
12 F05011-5 Washer, 5/8” SAE Flat 2
13 P05035 Collar, 5/8” Lock 2
14 F05009-10 Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 1
15 F05010-4 Nut, 5/8-11 Hex Lock 1
16 034726 PIN WELDMENT, 4 3/8” PIVOT 1

Bed Hydraulic System WM doc 5/11/23 9-13

 Bed Hydraulic System
9 Hydraulic Log Side Supports (Rear)

REF PART # DESCRIPTION COMMENTS QTY.

036053 PIN ASSEMBLY, SIDE SUPPORT PIVOT 1
17 034718 Pin, Grooved Pivot Available in assemblies only. 1
18 F04254-15 Ring, 1” 3100-100 Outside Retaining 2
19 P04107 Fitting, 3/16” Straight Grease 1
20 034711 PUSHER WELDMENT, LOWER SIDE SUPPORT 1
21 F05011-52 WASHER, 9/16” SAE FLAT 1
22 F05011-9 WASHER, 1/2” SPLIT LOCK 1
23 F05008-50 BOLT, 1/2-13 X 1” HEX HEAD 1
24 F05008-37 BOLT, 1/2”-13 X 1 1/4” HEX HEAD GRADE 5 2
25 F05010-8 NUT, 1/2-13 HEX NYLON LOCK 2
26 034716 ARM WELDMENT, VERTICAL SIDE SUPPORT 1
REAR LIFT
27 P04107 FITTING, 3/16” STRAIGHT GREASE 1
28 034728 PIN WELDMENT, 10 7/8” PIVOT 1
29 F05008-23 BOLT, 1/2-13 X 3” HEX HEAD GRADE 5 1

9-14 WM doc 5/11/23 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Log Side Supports (Link) 9
9.8 Hydraulic Log Side Supports (Link)

1 4
3
2
600019-3B

REF PART # DESCRIPTION COMMENTS QTY.

1 034725 ROD WELDMENT, SIDE SUPPORT LINK 1
2 106869 ARM WELDMENT, SIDE SUPPORT LINK 1
3 F05010-100 NUT, 1 1/4”-12 HEX JAM 2
4 P04107 FITTING, 3/16” STRAIGHT GREASE 3

Bed Hydraulic System WM doc 5/11/23 9-15

 Bed Hydraulic System
9 Hydraulic Log Clamp

9.9 Hydraulic Log Clamp

36

37 15
35
38

37 14 13
12
33 11
16
34 10
17 18
21 13 23 19
1
3 24 22
4
21 30
3 3 20 31
10 20
6
29 26
27
4 2 28
9 4
25 4
7
27
4 19
6 4
HD0157E 24
5 32 8 32 5 6 3 4
25
4 3
6

REF PART # DESCRIPTION COMMENTS QTY.

017264 CLAMP ASSEMBLY, HYDRAULIC 2-PLANE 1
1 017265 Mount Weldment, Hydraulic Clamp Slide 1
2 017267 Link Weldment, Hydraulic Clamp 1
3 015057 Washer, 1/8” x 2 1/2” Hardened 5
4 F05011-28 Washer, 1” SAE Flat 8
5 S09251 Pin, 1” x 3.88” 2
6 F05012-23 Pin, 3/16” x 1 1/2” Cotter 6
7 015049 Bolt, 1-14 x 8 1/2” Hex Head Grade 8 1
8 017275 Cylinder, 3” x 7” Hydraulic 1
061365 Seal kit for Bailey Cyl. 017275
P12956 Seal Kit, Hydraulic Cylinder P129956 used for J-D Cyl. 1
(Identify by notched gland
retaining nut)
9 017274 Arm, Clamp Pivot 1
10 015088 Bushing, Clamp Slide 2
017271 Wiper Assembly, Vertical Clamp Rod 1
11 017273 Wiper, Vertical Clamp Rod 1
12 017272 Flange, Vertical Clamp Rod Wiper 1

9-16 WM doc 5/11/23 Bed Hydraulic System

 Bed Hydraulic System
Hydraulic Log Clamp 9
REF PART # DESCRIPTION COMMENTS QTY.
13 F05011-17 Washer, 5/16” SAE Flat 8
14 F05006-1 Bolt, 5/16-18 x 1” Hex Head 2
15 015043 Clamp Weldment, Vertical 1
16 F05010-141 Nut, 1-14 Nylon Lock 1
17 017270 Block, Hydraulic Clamp Slide 1
18 015050 Cylinder Weldment, Vertical Clamp Hydraulic 1
061435 Seal kit for 1" Bailey Cyl. 015050 Used on Bailey Cyl. after 8/19 1
016204 Seal Kit, Hydraulic Cylinder 1
016204-1009 Instruction Sheet, Vertical Clamp 1
Seal Replacement
19 074543 Fitting, 4SAE-4JIC 90° Elbow Fitting, 1/4" NPT x 1/4" JIC 2
Elbow P09142 was replace with
074543 as of 11/6/2020, per
ECN 37711.
20 017242 Retainer, Clamp Bushing 3
21 F05006-5 Bolt, 5/16-18 x 3/4” Hex Head 6
22 F05008-39 Bolt, 1/2-13 x 2 1/2” Socket Head 2
23 P04107 Fitting, 3/16” Straight Grease 1
24 015072 Bolt, 1-14 x 3 3/4” Hex Head Grade 8 w/Hole 2
25 F05010-163 Nut, 1-14 Slotted Hex 2
26 015068 Plate, Log Clamp Mount 1
27 F05011-3 Washer, 3/8” SAE Flat 8
28 F05007-5 Bolt, 3/8-16 x 5” Hex Head 4
29 F05010-10 Nut, 3/8-16 Hex Nylon Lock 4
30 F05011-46 Washer, 7/8” Split Lock 1
31 F05014-2 Bolt, 7/8-14 x 2” Hex Head Grade 5 1
32 015491 Fitting, 1/4” NPT - 3/8” JIC Elbow 2
33 F05008-28 Bolt, 1/2-13 x 5 1/2” Hex Head Grade 5 2
34 F05010-8 Nut, 1/2-13 Hex Nylon Lock 2
K09485 Clamp Stop Kit, Hydraulic Log 1
35 W09404 Plate, Clamp Stop 1
36 F05008-33 Bolt, 1/2-13 X 1 1/2" Hex Head Grade 5 2
37 F05011-2 Washer, 1/2" SAE Flat 2
38 F05010-3 Nut, 1/2-13 Hex Lock 2

Bed Hydraulic System WM doc 5/11/23 9-17

 Bed Hydraulic System
9 Hydraulic Toe Board

9.10 Hydraulic Toe Board

1
4 3
2
5

6
5
14

11
13
7

15
8

12 10

16
600109C 11
11
10

REF PART # DESCRIPTION COMMENTS QTY.

1 074842 TOE BOARD ASSEMBLY, HYDRAULIC 2
2 F05012-82 PIN, 1/2-1 3/4 CLEVIS 4
3 F05011-2 WASHER, 1/2” SAE FLAT 4
4 F05012-3 PIN, 1/8 X 3/4” COTTER 4
5 F05009-33 BOLT, 5/8-11 X 1 3/4” HEX HEAD 4
6 F05011-27 WASHER, 5/8” SPLIT LOCK 4
7 S13023 PLATE, HYDRAULIC TOEBOARD MOUNT 2
8 S13022 BRACKET, HYDRAULIC TOEBOARD MOUNT 2
9 S09251 PIN, CYLINDER MOUNT 2
10 F05012-23 PIN, 3/16” X 1 1/2” COTTER 4
11 F05011-28 WASHER, 1” SAE FLAT 6
12 014482 CYLINDER, 1 1/2” X 6” HYDRAULIC TOE BOARD 2
014547 Seal Kit, 1 1/2” x 6” Hydraulic Cylinder 1
13 F05009-51 BOLT, 1-8 X 3 1/4” HEX HEAD GRADE 5 2
14 F05010-109 NUT, 1-8 HEX NYLON LOCK 2
15 P09143 FITTING, 1/4” NPT X 1/4” JIC MALE 2
16 P09142 FITTING, 1/4” NPT X 1/4” JIC MALE ELBOW 2

9-18 WM doc 5/11/23 Bed Hydraulic System

 Miscellaneous
Replacement Manuals 10
SECTION 10 MISCELLANEOUS
10.1 Replacement Manuals

HD0202-16

REF DESCRIPTION ( Indicates Parts Available In Assemblies Only) PART # QTY.

Wood-Mizer Product Information
1 ALL-PRODUCTS CATALOG PS750 1
Basic Sawmill Manuals
2 TRU-SHARP BLADE HANDBOOK M600 1
3 WOOD-MIZER GENERAL INFORMATION M601 1
4 LT50HD OPERATOR’S MANUAL M1661 1
5 LT50HD-WR WIRELESS OPERATOR’S MANUAL M1663 1
6 LT50HD PARTS MANUAL M1660 1
7 LT50HD-WR WIRELESS PARTS MANUAL M1662 1
Power Option Manuals
8 E25 MOTOR OPTION MANUAL M772 1
9 G38 ENGINE OPTION MANUAL M1305 1
10 D47 ENGINE OPTION MANUAL M1584 1
11 D51 ENGINE OPTION MANUAL M1163 1
Trailer Option Manuals
12 ELECTRIC BRAKE TRAILER OPTION M796 1
13 SURGE BRAKE TRAILER OPTION M794 1
14 SUPER ELECTRIC BRAKE TRAILER OPTION M797 1
15 SUPER SURGE BRAKE TRAILER OPTION M795 1
Miscellaneous Option Manuals
16 SHINGLE/LAPSIDER OPTION MANUAL M621 1
17 OPERATOR’S SEAT OPTION MANUAL M613 1
18 RESAW ATTACHMENT OPTION MANUAL M263 1
19 BED EXTENSION OPTION MANUAL M294 1
20 MKII DEBARKER ATTACHMENT OPTION MANUAL M546 1
21 ACCUSET 2 OPTION MANUAL M1517 1
22 LASER SIGHT OPTION MANUAL M679 1
23 AUTOCLUTCH OPTION MANUAL M883 1
24 LUBE-MIZER OPTION MANUAL M885 1
25 LATHE-MIZER OPTION MANUAL M1337 1
Electrical Diagrams
26 G38 SUPER ELECTRICAL INFORMATION M1306 1
27 G38-WR WIRELESS ELECTRICAL INFORMATION M1555 1

Miscellaneous WM doc 5/11/23 10-1

 Miscellaneous
10 Replacement Manuals

28 E25 ELECTRICAL INFORMATION M863 1

29 E25-WR WIRELESS ELECTRICAL INFORMATION M1554 1
30 D47 ELECTRICAL INFORMATION M1585 1
31 D47-WR WIRELESS ELECTRICAL INFORMATION M1587 1
32 D51 ELECTRICAL INFORMATION M1164 1
33 D51-WR WIRELESS ELECTRICAL INFORMATION M1553 1

10-2 WM doc 5/11/23 Miscellaneous