DROP FORGED ANCHOR SHACKLES

Size, working load limit, and trademark are permanently marked on all shackles. All shackles
and pins are heat treated. Loads are based on a safety factor of 6 to 1, except (**) which is 5
to 1. When tested all shackles are pulled at a uniform rate of speed in a direct tension.

Shackles Meet Performance Requirements of Federal Specifications RR-C-271D Type IVA*

Anchor —R ound P in – S crew P in – S afety
Working Dimensions – Inches Estimated
Load Inside O.D. Pin or Weight
Limit Size Width @ Tol. Width @ Length Tol. Eyes Bolt Dia. Per 100
in Tons Dia. Eyes (A) ± Bow (B) (C) ± (D) (E) in lbs.
1/3 3/16" 3/8" 1/16" 9/16" 7/8" 1/16" 5/8" 1/4" 7
1/2 1/4" 15/32" 1/16" 3/4" 1-1/8" 1/16" 3/4" 5/16" 13.5
3/4 5/16" 17/32" 1/16" 15/16" 1-1/4" 1/16" 7/8" 3/8" 22
1 3/8" 21/32" 1/16" 1-1/8" 1-7/16" 1/8" 1" 7/16" 33
1-1/2 7/16" 23/32" 1/16" 1-5/16" 1-11/16" 1/8" 1-1/8" 1/2" 53.5
2 1/2" 13/16" 1/16" 1-1/2" 1-15/16" 1/8" 1-1/4" 5/8" 76.5
3-1/4 5/8" 1-1/16" 1/16" 1-7/8" 2-1/2" 1/8" 1-11/16" 3/4" 150.5
4-3/4 3/4" 1-1/4" 1/16" 2" 3" 1/4" 1-7/8" 7/8" 245.5
6-1/2 7/8" 1-7/16" 1/16" 2-5/8" 3-1/4" 1/4" 2-1/8" 1" 375
8-1/2 1" 1-11/16" 1/16" 2-3/4" 3-3/4" 1/4" 2-1/2" 1-1/8" 537.5
9-1/2 1-1/8" 1-13/16" 1/16" 2-15/16" 4-1/4" 1/4" 2-5/8" 1-1/4" 765
12 1-1/4" 2" 1/16" 3-1/4" 4-1/2" 1/4" 3" 1-3/8" 1007.5
13 1/2 **1-3/8" 2-1/4" 1/8" 3-1/2" 5-1/4" 1/4" 3-1/4" 1-1/2" 1232.5
17 1-1/2" 2-3/8" 1/8" 3-3/4" 5-3/4" 1/4" 3-1/2" 1-5/8" 1777.5

WARNING:
Any deviations such as angular lifts, shock loads, modification of the basic forging, etc., will result in drastically
reduced working load limits.
All types of shackles are available in a self-colored or hot galvanized finish. When ordering specify the size,
finish, and type of shackle. Other rust preventative coatings are available on a special basis.
Safety shackles are of the same specifications as the regular types except for the bolt, nut and cotter.

*Class 1 *Class 2 *Class 3

ROUND PIN SCREW PIN SAFETY

Galvanized Self-Colored Galvanized Self-Colored Galvanized Self-Colored
Part Part Part Part Part Part
Size Size Size
No. No. No. No. No. No.
3/16" 21105 5 21005 8 3/16" 20105 6 20005 9 1/4" 20610 5 20510 8
1/4" 21110 9 21010 2 1/4" 20110 0 20010 3 5/16" 20615 0 20515 3
5/16" 21115 4 21015 7 5/16" 20115 5 20015 8 3/8" 20620 4 20520 7
3/8" 21120 8 21020 1 3/8" 20120 9 20020 2 7/16" 20625 9 20525 2
7/16" 21125 3 21025 6 7/16" 20125 4 20025 7 1/2" 20630 3 20530 6
1/2" 21130 7 21030 0 1/2" 20130 8 20030 1 5/8" 20635 8 20535 1
5/8" 21135 2 21035 5 5/8" 20135 3 20035 6 3/4" 20640 2 20540 5
3/4" 21140 6 21040 9 3/4" 20140 7 20040 0 7/8" 20645 7 20545 0
7/8" 21145 1 21045 4 7/8" 20145 2 20045 5 1" 20650 1 20550 4
1" 21150 5 21050 8 1" 20150 6 20050 9 1-1/8" 20655 6 20555 9
1-1/8" 21155 0 21055 3 1-1/8" 20155 1 20055 4 1-1/4" 20660 0 20560 3
1-1/4" 21160 4 21060 7 1-1/4" 20160 5 20060 8 1-1/2" 20670 9 20570 2
1-3/8" 21165 9 21065 2 1-3/8" 20165 0 20065 3
1-1/2" 21170 3 21070 6 1-1/2" 20170 4 20070 7 Made in U S A

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 9

 DROP FORGED CHAIN SHACKLES
Size, working load, and trademark are permanently marked on all shackles. All shackles
and pins are heat treated. Loads are based on a safety factor of 6 to 1. When tested all
shackles are pulled at a uniform rate of speed in a direct tension.

Shackles Meet Performance Requirements of Federal Specifications RR-C-271D Type IVB*

Chain — Round Pin – Screw Pin – Safety

Working Dimensions – Inches Estimated
Load Inside O.D. Pin or Weight
Limit Size Width Tol. Length Tol. Eyes Bolt Dia. Per 100
in Tons Dia. (A) ± (B) ± (C) (D) in lbs.
1/2 1/4" 15/32" 1/16" 7/8" 1/16" 3/4" 5/16" 11
3/4 5/16" 17/32" 1/16" 1" 1/16" 7/8" 3/8" 20
1 3/8" 21/32" 1/16" 1-1/4" 1/8" 1" 7/16" 31.5
1-1/2 7/16" 23/32" 1/16" 1-1/2" 1/8" 1-1/8" 1/2" 45.5
2 1/2" 13/16" 1/16" 1-11/16" 1/8" 1-1/4" 5/8" 69.5
3-1/4 5/8" 1-1/16" 1/16" 2" 1/8" 1-5/8" 3/4" 132.5
4-3/4 3/4" 1-1/4" 1/16" 2-5/16" 1/4" 1-7/8" 7/8" 212
6-1/2 7/8" 1-7/16" 1/16" 2-7/8" 1/4" 2-1/8" 1" 320
8-1/2 1" 1-11/16" 1/16" 3-1/4" 1/4" 2-1/2" 1-1/8" 500

WARNING:

Any deviations such as angular lifts, shock loads, modification of the basic forging, etc., will result in drasti-
cally reduced working load limits.

All types of shackles are available in a self-colored or hot galvanized finish. When ordering specify the size,
finish, and type of shackle. Other rust preventative coatings are available on a special basis.
Safety shackles are of the same specifications as the regular types except for the bolt, nut and cotter.

*Class 1 *Class 2 *Class 3

ROUND PIN SCREW PIN SAFETY

Galvanized Self-Colored Galvanized Self-Colored Galvanized Self-Colored
Part Part Part Part Part Part
Size Size Size
No. No. No. No. No. No.
1/4" 21310 3 21210 6 1/4" 20310 4 20210 7 1/4" 20810 9 20710 2
5/16" 21315 8 21215 1 5/16" 20315 9 20215 2 5/16" 20815 4 20715 7
3/8" 21320 2 21220 5 3/8" 20320 3 20220 6 3/8" 20820 8 20720 1
7/16" 21325 7 21225 0 7/16" 20325 8 20225 1 7/16" 20825 3 20725 6
1/2" 21330 1 21230 4 1/2" 20330 2 20230 5 1/2" 20830 7 20730 0
5/8" 21335 6 21235 9 5/8" 20335 7 20235 0 5/8" 20835 2 20735 5
3/4" 21340 0 21240 3 3/4" 20340 1 20240 4 3/4" 20840 6 20740 9
7/8" 21345 5 21245 8 7/8" 20345 6 20245 9 7/8" 20845 1 20745 4
1" 21350 9 21250 2 1" 20350 0 20250 3 1" 20850 5 20750 8

Made in U S A

10 Chicago Hardware and Fixture Company Since 1912

 MALLEABLE WIRE ROPE CLIPS
Clips supplied with self-colored, galvanized or hot galvanized finish. U-bolts for clips
are available with or without nuts — price on application.

Made in U S A

Should be used
only in
light duty applications

Meets Performance Requirements of Federal Specification FF-C-450, Type 1, Class 2

Some sizes available in Stainless Steel. See page 47.

Hot
Self-Colored Galvanized U-Bolt Dimensions Weight
Galvanized
Rope Size Part No. Part No. Part No. A B C T Per 100
3/32" 23005 6 23155 8 N.A. 10-24 3/4" 19/64" 1/2" 3.7
1/8" 23010 0 23160 2 N.A. 1/4"-20 15/16" 5/16" 5/8" 6.5
3/16" 23015 5 23165 7 N.A. 1/4"-20 15/16" 5/16" 5/8" 6.8
1/4" 23020 9 23170 1 23320 0 5/16"-18 1-5/32" 3/8" 3/4" 12.2
5/16" 23025 4 23175 6 23325 5 5/16"-18 1-5/32" 3/8" 3/4" 12.2
3/8" 23030 8 23180 0 23330 9 3/8"-16 1-1/2" 1/2" 1" 18.5
7/16" 23035 3 23185 5 23335 4 3/8"-16 1-1/2" 1/2" 1" 24
1/2" 23040 7 23190 9 23340 8 7/16"-14 1-13/16" 9/16" 1-1/8" 33.3
9/16" 23045 2 23195 4 23345 3 1/2"-13 2-1/8" 11/16" 1-3/8" 51.5
5/8" 23050 6 23200 5 23350 7 1/2"-13 2-1/8" 11/16" 1-3/8" 55.9
3/4" 23055 1 23205 0 23355 2 9/16"-12 2-11/16" 13/16" 1-5/8" 80.8
7/8" 23060 5 23210 4 23360 6 5/8"-11 3-1/4" 1-1/8" 1-7/8" 140
1" 23065 0 23215 9 23365 1 5/8"-11 3-1/4" 1-1/8" 1-7/8" 150
1-1/8" 23070 4 23220 3 N.A. 3/4"-10 4-3/8" 1-5/16" 2-1/2" 263
1-1/4" 23075 9 23225 8 N.A. 3/4"-10 4-3/8" 1-5/16" 2-1/2" 300
1-3/8" 23080 3 23230 2 N.A. 7/8"-9 5-1/8" 1-11/16" 2-3/4" 441
1-1/2" 23085 8 23235 7 N.A. 7/8"-9 5-1/8" 1-11/16" 2-3/4" 488
1-3/4" 23095 7 23245 6 N.A. 1"-8 6-1/4" 2-1/16" 3-3/4" 899.5
2" 23100 8 23250 0 N.A. 1"-8 7-1/4" 2-1/2" 4" 1285

TILLER Rope
Part No.
Overall Overall Weight
Diameter Length Width Per 100
ROPE 1/8" 27910 9 1-5/8" 3/4" 10 Lbs.
CLAMPS 3/16" 27920 8 1-3/4" 3/4" 12 Lbs.

Malleable iron castings hot galvanized finish. Furnished with brass flat head machine screws.

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 11

 DROP FORGED WIRE ROPE CLIPS
“CHICAGO” the Trade-Mark of quality in wire rope fittings is embossed on all forged
steel clip bases. This identification symbolizes wire rope clips that are manufactured
to rigid specifications. Component parts are galvanized. U-bolts, with or without nuts,
price on application.
Made in U S A
Should be used in heavy duty applications

Hot
U-Bolt Dimensions Weight
Galvanized
Rope Size Part No. A B C T Per 100
1/8" 23460 3 12-24 3/4" 9/32" 1/2" 6.5
3/16" 23465 8 1/4"-20 15/16" 5/16" 5/8" 10
1/4" 23470 2 5/16"-18 1-5/32" 3/8" 3/4" 18.5
5/16" 23475 7 3/8"-16 1-1/2" 1/2" 1" 29.5
3/8" 23480 1 7/16"-14 1-5/8" 9/16" 7/8" 44
7/16" 23485 6 1/2"-13 1-7/8" 5/8" 1-1/4" 64
1/2" 23490 0 1/2"-13 1-7/8" 5/8" 1-1/4" 75
9/16" 23495 5 9/16"-12 2-3/8" 3/4" 1-3/8" 106
5/8" 23500 6 9/16"-12 2-3/8" 3/4" 1-3/8" 106
3/4" 23505 1 5/8"-11 2-3/4" 7/8" 1-5/8" 153
7/8" 23510 5 3/4"-10 3-1/4" 1" 1-7/8" 237.5
1" 23515 0 3/4"-10 3-5/8" 1-1/8" 2" 272.5
1-1/8" 23520 4 3/4"-10 3-13/16" 1-1/4" 2-1/4" 325
1-1/4" 23525 9 7/8"-9 4-3/8" 1-11/32" 2-1/2" 441
1-1/2" 23535 8 7/8"-9 5-1/8" 1-11/16" 2-3/4" 550

Meets Performance Requirements of Federal Specification FF-C-450, Type 1, Class 1

1 2 3

RECOMMENDED APPLICATION FOR CHICAGO DROP FORGED WIRE ROPE CLIPS

1. The correct way to attach wire rope clips is illustrated above. Apply the first clip
Clip Minimum Amount of Rope one base width from the dead end of the wire rope. The base or saddle should bear
Torque in
Size No. of to Turn Back on the line end of the rope – U-bolt on the short end. Tighten nuts firmly.
Ft. Lbs.
Inches Clips in Inches
2. Attach second clip as close to loop as possible. Tighten nuts but not firmly.
1/8" 2 3-1/4" 4.5
3/16" 2 3-3/4" 7.5 3. Attach balance of clips spaced equally between first two clips. Tighten all nuts
1/4" 2 4-3/4" 15 completely. Apply initial load – inspect nuts and retighten. Inspect all clips
5/16" 2 5-1/4" 30 periodically.
3/8" 2 6-1/2" 45
7/16" 2 7" 65 The number of clips shown is based on using right regular or Lang lay wire rope,
1/2" 3 11-1/2" 65 6x19 class or 6x37 class, fibre core IWRC, IPS or XIPS. The number of clips shown
9/16" 3 12" 95 also applies to right regular lay wire rope, 8x19 class and 18x7 class, fibre core, IPS
5/8" 3 12" 95 or XIPS, sizes 1-1/2-inch and smaller.
3/4" 4 18" 130
7/8" 4 19" 225 If Seale construction or similar large outer wire type construction in the 6x19 class is
1" 5 26" 225 to be used for sizes 1-inch and larger, add one additional clip. For other classes or
1-1/8" 6 34" 225 wire rope not mentioned, it may be necessary to add additional clips to the number
1-1/4" 7 44" 360 shown. If more clips are used than shown, amount of rope turn back should be
1-1/2" 8 54" 360 increased proportionately.

12 Chicago Hardware and Fixture Company Since 1912

 WIRE ROPE THIMBLES
Available in closed or open pattern with galvanized finish.

Made in U S A

CLOSED OPEN
STANDARD Dimensions – Inches Weight
Rope Closed Open Length Width Per
Diameter Part No. Part No. Overall Inside Inside Opening Inside score 100
1/8" 22505 2 22405 5 1-5/8" 1-7/32" 19/32" 3/8" 3/16" 2.1
3/16" 22510 6 22410 9 1-5/8" 1-7/32" 19/32" 3/8" 7/32" 2.1
1/4" 22515 1 22415 4 1-7/8" 1-3/8" 11/16" 1/2" 1/4" 3.4
5/16" 22520 5 22420 8 2-1/8" 1-1/2" 3/4" 5/8" 5/16" 4.6
3/8" 22525 0 22425 3 2-5/8" 1-7/8" 7/8" 5/8" 13/32" 9
7/16" 22530 4 22430 7 2-3/4" 1-7/8" 1-1/16" 3/4" 15/32" 17
1/2" 22535 9 22435 2 2-7/8" 2" 1-1/8" 3/4" 19/32" 17
5/8" 22540 3 22440 6 3-3/8" 2-7/32" 1-5/16" 7/8" 23/32" 30
3/4" 22545 8 22445 1 3-7/8" 2-1/2" 1-1/2" 1" 13/16" 39.5
7/8" 22550 2 22450 5 4-9/16" 3" 1-11/16" 1-1/8" 15/16" 58.5
1" 22555 7 22455 0 5" 3-7/32" 2" 1-1/8" 1-1/8" 96
1-1/8" 22560 1 N.A. 5-3/8" 3-9/16" 2-1/4" N.A. 1-1/4" 108.5
1-1/4" 22565 6 N.A. 5-3/4" 3-9/16" 2-7/16" N.A. 1-5/16" 145.5
1-1/2" 22570 0 N.A. 7" 4-5/16" 2-7/8" N.A. 1-9/16" 246.5
1-3/4" 22575 5 N.A. 8-1/2" 5-1/4" 3-5/16" N.A. 1-7/8" 460
2" 22580 9 N.A. 10" 6-5/8" 3-1/2" N.A. 2-3/32" 590

Recommended for light duty applications.

Some sizes also available in Stainless Steel. See page 47.

HEAVY DUTY

Dimensions – Inches Weight

Rope Part Length Width Per
Diameter No. Overall Inside Inside Inside score 100
1/4" 22105 4 2-3/16" 1-5/8" 7/8" 1/4" 6.5
5/16" 22110 8 2-1/2" 1-7/8" 1-1/16" 11/32" 11.8
3/8" 22115 3 2-7/8" 2-1/8" 1-1/8" 13/32" 21.6
7/16" 22120 7 3-1/4" 2-3/8" 1-1/4" 15/32" 34.7
1/2" 22125 2 3-5/8" 2-3/4" 1-1/2" 17/32" 51
9/16"-5/8" 22130 6 4-1/4" 3-1/4" 1-3/4" 21/32" 51
3/4" 22135 1 5" 3-3/4" 2" 25/32" 158
7/8" 22140 5 5-1/2" 4-1/4" 2-1/4" 15/16" 178
1" 22145 0 6-1/8" 4-1/2" 2-1/2" 1-1/16" 314
1-1/8"-1-1/4" 22150 4 7" 5-1/8" 2-7/8" 1-5/16" 400
1-3/8"-1-1/2" 22155 9 9" 6-1/4" 3-1/2" 1-9/16" 1295

Recommended for heavy duty applications.

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 13

 DROP FORGED EYE BOLTS
Regular, shoulder and screw thread (see page 15) drop forged heat treated steel eye bolts supplied
as standard with hot galvanized finish. Machine thread eye bolts are threaded National Course
before galvanizing and assembled with hex nuts tapped oversize. Loads are based on a safety
factor of 5 to 1. When tested all eye bolts are pulled at a uniform rate of speed in a direct tension.

REGULAR – MACHINE THREAD Made in U S A

Dimensions – Inches Weight Working

Diameter (A) & Outside Inside Overall Thread Per Load
Part No. 100 pcs Limit
Shank Length (B) Eye (C) Eye (D) Length (E) Length (T)
1/4" x 2" 08005 7 1" 1/2" 3" 1-1/2" 6.4 500
1/4" x 3" 08008 8 1" 1/2" 4" 1-1/2" 8 500 WARNING:
1/4" x 4" 08011 8 1" 1/2" 5" 2" 9.3 500
1/4" x 5" 08014 9 1" 1/2" 6" 2-1/2" 10.4 500 Any deviations such
1/4" x 6" 08017 0 1" 1/2" 7" 3" 11.8 500 as angular lifts, shock
5/16" x 2-1/4" 08022 4 1-1/4" 5/8" 3-1/2" 1-1/2" 12.7 800 loads, modification of
5/16" x 3-1/4" 08025 5 1-1/4" 5/8" 4-1/2" 1-1/2" 15 800 the basic forging, etc.,
5/16" x 4-1/4" 08028 6 1-1/4" 5/8" 5-1/2" 2-1/2" 16.5 800 will result in drastically
5/16" x 5" 08031 6 1-1/4" 5/8" 6-1/4" 2-1/2" 18.6 800 reduced working load
5/16" x 6" 08034 7 1-1/4" 5/8" 7-1/4" 3" 24.5 800 limits.
3/8" x 2-1/2" 08039 2 1-1/2" 3/4" 4" 1-1/2" 19.2 1200
3/8" x 3" 08042 2 1-1/2" 3/4" 4-1/2" 1-1/2" 21.2 1200
3/8" x 4-1/4" 08045 3 1-1/2" 3/4" 6" 2" 24.4 1200
3/8" x 5" 08048 4 1-1/2" 3/4" 6-1/2" 2-1/2" 27.8 1200 Special shank
3/8" x 6" 08051 4 1-1/2" 3/4" 7-1/2" 3" 30 1200 and thread lengths
3/8" x 8" 08054 5 1-1/2" 3/4" 9-1/2" 4" 36 1200 are also available.
1/2" x 2" 08059 0 2" 1" 4" 1-7/8" 38.5 2200
1/2" x 3-1/4" 08062 0 2" 1" 5-1/4" 1-1/2" 46 2200
1/2" x 4-1/2" 08065 1 2" 1" 6-1/2" 2" 53 2200
1/2" x 6" 08068 2 2" 1" 8" 3" 60 2200
1/2" x 8" 08071 2 2" 1" 10" 4" 71 2200
1/2" x 10" 08074 3 2" 1" 12" 4" 83 2200
1/2" x 12" 08077 4 2" 1" 14" 4" 96 2200
5/8" x 4-1/2" 08082 8 2-5/16" 1-1/4" 6-13/16" 2" 79 3500
5/8" x 6" 08085 9 2-5/16" 1-1/4" 8-5/16" 3" 96 3500
5/8" x 8" 08088 0 2-5/16" 1-1/4" 10-5/16" 4" 128 3500
5/8" x 10" 08091 0 2-5/16" 1-1/4" 12-5/16" 4" 129.5 3500
5/8" x 12" 08094 1 2-5/16" 1-1/4" 14-5/16" 4" 146 3500
5/8" x 15" 08097 2 2-5/16" 1-1/4" 17-5/16" 6" 168 3500
5/8" x 18" 08100 9 2-5/16" 1-1/4" 20-5/16" 6" 195 3500
5/8" x 24" 08103 0 2-5/16" 1-1/4" 26-5/16" 6" 246 3500
3/4" x 4-1/2" 08108 5 2-3/4" 1-1/2" 7-1/4" 2-1/2" 126 5200
3/4" x 6" 08111 5 2-3/4" 1-1/2" 8-3/4" 3" 160 5200
3/4" x 8" 08114 6 2-3/4" 1-1/2" 10-3/4" 4" 180 5200
Some sizes
3/4" x 10" 08117 7 2-3/4" 1-1/2" 12-3/4" 4" 200 5200
also available in
3/4" x 12" 08120 7 2-3/4" 1-1/2" 14-3/4" 4" 233 5200
Stainless Steel.
3/4" x 15" 08123 8 2-3/4" 1-1/2" 17-3/4" 6" 254 5200
See page 47.
3/4" x 18" 08126 9 2-3/4" 1-1/2" 20-3/4" 6" 290 5200
3/4" x 24" 08129 0 2-3/4" 1-1/2" 26-3/4" 6" 369 5200
7/8" x 5" 08134 4 3-1/2" 1-3/4" 8-1/2" 2-1/2" 245 7000
7/8" x 8" 08137 5 3-1/2" 1-3/4" 11-1/2" 4" 296 7000
7/8" x 12" 08140 5 3-1/2" 1-3/4" 15-1/2" 4" 366 7000
7/8" x 18" 08143 6 3-1/2" 1-3/4" 21-1/2" 6" 464 7000
7/8" x 24" 08146 7 3-1/2" 1-3/4" 27-1/2" 6" 556 7000
1" x 6" 08151 1 3-3/4" 2" 9-3/4" 3" 301 10000
1" x 9" 08154 2 3-3/4" 2" 12-3/4" 4" 383 10000
1" x 12" 08157 3 3-3/4" 2" 15-3/4" 4" 450 10000
1" x 18" 08160 3 3-3/4" 2" 21-3/4" 6" 584 10000
1" x 24" 08163 4 3-3/4" 2" 27-3/4" 6" 716 10000

14 Chicago Hardware and Fixture Company Since 1912

 DROP FORGED EYE BOLTS
MACHINE THREAD (As noted on page 14)

WARNING:
Any deviations such as angular lifts, shock loads,
modification of the basic forging, etc., will result in Made in U S A
drastically reduced working load limits.

SHOULDER Dimensions – Inches Weight Working

Diameter (A) & Outside Inside Overall Outside Thickness at Thread Per Load
Part No. 100 pcs Limit✝
Shank Length (B) Eye (C) Eye (D) Length (E) Shoulder (F) Shoulder (G) Length (T)
1/4" x 2" 08405 5 1" 1/2" 3-1/8" 7/16" 5/64" 1-1/2" 7.4 500
1/4" x 4" 08411 6 1" 1/2" 5-1/8" 7/16" 5/64" 2" 10.7 500
5/16" x 2-1/4" 08422 2 1-1/4" 5/8" 3-5/8" 9/16" 3/32" 1-1/2" 12.9 800
5/16" x 4-1/4" 08428 4 1-1/4" 5/8" 5-5/8" 9/16" 3/32" 2-1/2" 16.8 800
3/8" x 2-1/2" 08439 0 1-1/2" 3/4" 4-1/4" 11/16" 1/8" 1-1/2" 21 1200
3/8" x 4-1/2" 08445 1 1-1/2" 3/4" 6-1/4" 11/16" 1/8" 2" 29 1200
1/2" x 2" 08459 8 2" 1" 4-5/16" 7/8" 5/32" 1-7/8" 44 2200
1/2" x 3-1/4" 08462 8 2" 1" 5-1/2" 7/8" 5/32" 1-1/2" 46 2200
1/2" x 6" 08468 0 2" 1" 8-1/4" 7/8" 5/32" 3" 63 2200
5/8" x 4-1/2" 08482 6 2-5/16" 1-1/4" 7-1/4" 1-1/8" 13/64" 2" 99 3500
5/8" x 6" 08485 7 2-5/16" 1-1/4" 8-9/16" 1-1/8" 13/64" 3" 103 3500
3/4" x 4-1/2" 08508 3 2-3/4" 1-1/2" 7-3/4" 1-3/8" 1/4" 2-1/2" 152 5200
3/4" x 6" 08511 3 2-3/4" 1-1/2" 9-1/8" 1-3/8" 1/4" 3" 166 5200
7/8" x 5" 08534 2 3-1/2" 1-3/4" 9-1/4" 1-1/2" 9/32" 2-1/2" 222 7000
7/8" x 8" 08537 3 3-1/2" 1-3/4" 12-1/8" 1-1/2" 9/32" 4" 269 7000
1" x 6" 08551 9 3-3/4" 2" 10-1/2" 1-3/4" 5/16" 3" 331 10000
1" x 9" 08554 0 3-3/4" 2" 13-1/4" 1-3/4" 5/16" 4" 404 10000
✝
Loads are based on a safety factor of 5 to 1. Some sizes also available in Stainless Steel. See page 47.
Special shank and thread lengths are also available.

SCREW THREAD EYE BOLTS

REGULAR Dimensions – Inches Weight
Diameter (A) & Outside Inside Overall Thread Per
Part No. 100
Shank Length (B) Eye (C) Eye (D) Length (E) Length (T)
1/4" x 2" 08805 3 1" 1/2" 3" 1-1/2" 5.3
5/16" x 2-1/4" 08810 7 1-1/4" 5/8" 3-1/2" 1-5/8" 9 Made in U S A
3/8" x 2-1/2" 08815 2 1-1/2" 3/4" 4" 1-3/4" 16
1/2" x 3-1/4" 08820 6 2" 1" 5-1/4" 2-1/8" 39
5/8" x 4-1/2" 08825 1 2-5/16" 1-1/4" 6-13/16" 2-1/2" 67
3/4" x 4-1/2" 08830 5 2-3/4" 1-1/2" 7-1/4" 3" 108
7/8" x 5" 08835 0 3-1/2" 1-3/4" 8-1/4" 3-1/4" 166
1" x 6" 08840 4 3-3/4" 2" 9-3/4" 3-1/2" 265

Screw eye bolts supplied with cone points – lag screw thread.

SHOULDER Dimensions – Inches Weight

Diameter (A) & Outside Inside Overall Outside Thickness at Thread Per
Part No. 100 pcs
Shank Length (B) Eye (C) Eye (D) Length (E) Shoulder (F) Shoulder (G) Length (T)
1/4" x 2" 08905 0 1" 1/2" 3-1/8" 7/16" 5/64" 1-1/2" 6.7
5/16" x 2-1/4" 08910 4 1-1/4" 5/8" 3-3/4" 9/16" 3/32" 1-5/8" 12
3/8" x 2-1/2" 08915 9 1-1/2" 3/4" 4-1/4" 11/16" 1/8" 1-3/4" 19
1/2" x 3-1/4" 08920 3 2" 1" 5-1/2" 7/8" 5/32" 2-1/8" 42
5/8" x 4-1/2" 08925 8 2-5/16" 1-1/4" 7-1/4" 1-1/8" 13/64" 2-1/2" 86
3/4" x 4-1/2" 08930 2 2-3/4" 1-1/2" 7-3/4" 1-3/8" 1/4" 3" 120
7/8" x 5" 08935 7 3-1/2" 1-3/4" 9" 1-1/2" 9/32" 3-1/4" 189
1" x 6" 08940 1 3-3/4" 2" 10-1/2" 1-3/4" 5/16" 3-1/2" 297

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 15

 DROP FORGED *RING BOLTS
Ring bolts are only available in hot galvanized finish. Eye bolts are drop forged steel; eye
bolt specifications are identical to those shown on pages 14-15. Ring dimensions are
shown in table below. RING BOLTS ARE NOT TO BE USED FOR LIFTING APPLICATIONS.

REGULAR – MACHINE THREAD

Dimensions – Inches Weight Working
Diameter (A) & O.D. Eye I.D. Eye I.D. Eye Overall Thread Per Load
Part No. 100 pcs Limit
Shank Length (B) of Bolt (C) of Bolt (D) of Ring Length (E) Length (T)
1/4" x 2" 09205 0 1" 1/2" 1-3/4" 4-3/4" 1-1/2" 16 250
1/4" x 4" 09211 1 1" 1/2" 1-3/4" 6-3/4" 2" 18 250
5/16" x 2-1/4" 09216 6 1-1/4" 5/8" 2" 5-1/2" 1-1/2" 29 400
5/16" x 4-1/4" 09219 7 1-1/4" 5/8" 2" 7-1/2" 2-1/2" 32.5 400
3/8" x 2-1/2" 09224 1 1-1/2" 3/4" 2-1/2" 6-1/2" 1-1/2" 47.5 600
3/8" x 4-1/4" 09227 2 1-1/2" 3/4" 2-1/2" 8-1/4" 2" 52 600
3/8" x 6" 09230 2 1-1/2" 3/4" 2-1/2" 10" 3" 56 600
3/8" x 8" 09233 3 1-1/2" 3/4" 2-1/2" 12" 4" 62 600
1/2" x 3-1/4" 09238 8 2" 1" 3" 8-1/4" 1-1/2" 108 1100
Made in U S A 1/2" x 6" 09241 8 2" 1" 3" 11" 3" 121 1100
1/2" x 8" 09244 9 2" 1" 3" 13" 4" 135.5 1100
1/2" x 10" 09247 0 2" 1" 3" 15" 4" 142.5 1100
5/8" x 4-1/2" 09252 4 2-5/16" 1-1/4" 2-3/4" 9-9/16" 2" 175 1750
5/8" x 6" 09255 5 2-5/16" 1-1/4" 2-3/4" 11-1/16" 3" 190 1750
5/8" x 8" 09258 6 2-5/16" 1-1/4" 2-3/4" 13-1/16" 4" 200 1750
5/8" x 10" 09261 6 2-5/16" 1-1/4" 2-3/4" 15-1/16" 4" 231 1750
5/8" x 12" 09264 7 2-5/16" 1-1/4" 2-3/4" 17-1/16" 4" 242 1750
3/4" x 4-1/2" 09269 2 2-3/4" 1-1/2" 3" 10-1/4" 2-1/2" 281 2600
3/4" x 6" 09272 2 2-3/4" 1-1/2" 3" 11-3/4" 3" 311.5 2600
3/4" x 8" 09275 3 2-3/4" 1-1/2" 3" 13-3/4" 4" 312.5 2600
3/4" x 10" 09278 4 2-3/4" 1-1/2" 3" 15-3/4" 4" 315 2600
3/4" x 12" 09281 4 2-3/4" 1-1/2" 3" 17-3/4" 4" 317.5 2600
7/8" x 5" 09286 9 3-1/2" 1-3/4" 3-1/4" 11-1/2" 2-1/2" 520 3500
7/8" x 8" 09289 0 3-1/2" 1-3/4" 3-1/4" 14-1/2" 4" 538 3500
1" x 6" 09294 4 3-3/4" 2" 3-3/4" 13-1/2" 3" 645 4900
1" x 9" 09297 5 3-3/4" 2" 3-3/4" 16-1/2" 4" 741 4900

*Welded Rings

SHOULDER – MACHINE THREAD

Dimensions – Inches Weight Working
Diameter (A) & O.D. Eye I.D. Eye I.D. Eye Overall Outside Thickness at Thread Per Load
Part No.
Shank Length (B) of Bolt (C) of Bolt (D) of Ring Length (E) Shoulder (F) Shoulder (G) Length (T) 100 pcs Limit
1/4" x 2" 09505 1 1" 1/2" 1-3/4" 4-3/4" 7/16" 5/64" 1-1/2" 17 250
1/4" x 4" 09511 2 1" 1/2" 1-3/4" 6-1/4" 7/16" 5/64" 2" 19 250
5/16" x 2-1/4" 09516 7 1-1/4" 5/8" 2" 5-3/4" 9/16" 3/32" 1-1/2" 30 400
5/16" x 4-1/4" 09519 8 1-1/4" 5/8" 2" 6-5/8" 9/16" 3/32" 2" 33.5 400
3/8" x 2-1/2" 09524 2 1-1/2" 3/4" 2-1/2" 6-1/2" 11/16" 1/8" 1-1/2" 51 600
3/8" x 4-1/2" 09527 3 1-1/2" 3/4" 2-1/2" 8-3/4" 11/16" 1/8" 2" 58 600
1/2" x 3-1/4" 09538 9 2" 1" 3" 8-7/16" 7/8" 5/32" 1-1/2" 115 1100
1/2" x 6" 09541 9 2" 1" 3" 11" 7/8" 5/32" 3" 127 1100
5/8" x 4-1/2" 09552 5 2-5/16" 1-1/4" 2-3/4" 10" 1-1/8" 13/64" 2" 187.5 1750
5/8" x 6" 09555 6 2-5/16" 1-1/4" 2-3/4" 11-1/2" 1-1/8" 13/64" 3" 208 1750
3/4" x 4-1/2" 09569 3 3" 1-1/2" 3" 11" 1-3/8" 1/4" 2-1/2" 288 2600
3/4" x 6" 09572 3 3" 1-1/2" 3" 12-1/8" 1-3/8" 1/4" 3" 310 2600
7/8" x 5" 09586 0 3-1/2" 1-3/4" 3-1/4" 12" 1-1/2" 9/32" 2-1/2" 445 3500
7/8" x 8" 09589 1 3-1/2" 1-3/4" 3-1/4" 15" 1-1/2" 9/32" 4" 482 3500
1" x 6" 09594 5 3-3/4" 2" 3-3/4" 14" 1-3/4" 5/16" 3" 681 4900
1" x 9" 09597 6 3-3/4" 2" 3-3/4" 17" 1-3/4" 5/16" 4" 750 4900

16 Chicago Hardware and Fixture Company Since 1912

 DROP FORGED *RING BOLTS
Ring bolts are only available in hot galvanized finish. Eye bolts are drop forged steel;
screw thread eye bolt specifications are identical to those shown on the bottom of page
15. Ring dimensions are shown in table below. RING BOLTS ARE NOT TO BE USED FOR
LIFTING APPLICATIONS.

REGULAR – SCREW THREAD

Dimensions – Inches Weight
Diameter (A) & O.D. Eye I.D. Eye I.D. Eye Overall Thread Per
Part No. 100 pcs
Shank Length (B) of Bolt (C) of Bolt (D) of Ring Length (E) Length (T)
1/4" x 2" 09005 6 1" 1/2" 1-3/4" 4-3/4" 1-1/2" 16.7
5/16" x 2-1/4" 09010 0 1-1/4" 5/8" 2" 5-1/2" 1-5/8" 25.9
3/8" x 2-1/2" 09015 5 1-1/2" 3/4" 2-1/2" 6-1/2" 1-3/4" 44.3
1/2" x 3-1/4" 09020 9 2" 1" 3" 8-1/4" 2-1/8" 100.7
5/8" x 4-1/2" 09025 4 2-5/16" 1-1/4" 2-3/4" 9-9/16" 2-1/2" 162
3/4" x 4-1/2" 09030 8 2-3/4" 1-1/2" 3" 10-1/4" 3" 253
7/8" x 5" 09035 3 3-1/4" 1-3/4" 3-1/4" 11-1/2" 3-1/4" 403
1" x 6" 09040 7 3-3/4" 2" 3-3/4" 13-1/2" 3-1/2" 599

*Welded Rings

SHOULDER – SCREW THREAD

Dimensions – Inches Weight
Diameter (A) & O.D. Eye I.D. Eye I.D. Eye Overall Outside Thickness at Thread Per
Part No. 100 pcs
Shank Length (B) of Bolt (C) of Bolt (D) of Ring Length (E) Shoulder (F) Shoulder (G) Length (T)
1/4" x 2" 09105 3 1" 1/2" 1-3/4" 4-3/4" 7/16" 5/64" 1-1/2" 15.3
5/16" x 2-1/4" 09110 7 1-1/4" 5/8" 2" 5-1/2" 9/16" 3/32" 1-5/8" 28.9
3/8" x 2-1/2" 09115 2 1-1/2" 3/4" 2-1/2" 6-1/2" 11/16" 1/8" 1-3/4" 45.8
1/2" x 3-1/4" 09120 6 2" 1" 3" 8-1/4" 7/8" 5/32" 2-1/8" 105.8
5/8" x 4-1/2" 09125 1 2-5/16" 1-1/4" 2-3/4" 10-1/4" 1-1/8" 13/64" 2-1/2" 170
3/4" x 4-1/2" 09130 5 2-3/4" 1-1/2" 3" 11" 1-3/8" 1/4" 3" 272
7/8" x 5" 09135 0 3-1/4" 1-3/4" 3-1/4" 12" 1-1/2" 9/32" 3-1/4" 429
1" x 6" 09140 4 3-3/4" 2" 3-3/4" 14-1/2" 1-3/4" 5/16" 3-1/2" 647

*Welded Rings
Made in U S A

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 17

 MACHINERY EYE BOLTS
Maximum blank lengths, either pattern indicated in column (1). Vertical loads are based
on a safety factor of 5 to 1. Variation in quantity: on special items we reserve the right to
a maximum 10% variation for allowances in manufacture.

STANDARD SHANK LENGTHS – PLAIN & SHOULDER PATTERN

Stock Numbers Dimensions – Inches
Plain Shoulder Shank Eye Overall Length Overall Length Maximum
Pattern Pattern Dia. & Thread Length I.D. O.D. Plain Shoulder Lengths (1)
1 21 1/4"-20 1" 3/4" 1-1/4" 2-1/4" 2-3/8" 3"
2 22 5/16"-18 1-1/8" 7/8" 1-1/2" 2-5/8" 2-3/4" 4"
3 23 3/8"-16 1-1/4" 1" 1-21/32" 2-29/32" 3-1/4" 4-1/2"
4 24 7/16"-14 1-3/8" 1-3/32" 1-27/32" 3-7/32" 3-5/8" 4-1/2"
5 25 1/2"-13 1-1/2" 1-3/16" 2-1/16" 3-9/16" 4" 4-1/2"
6 26 9/16"-12 1-5/8" 1-9/32" 2-9/32" 3-29/32" 4-1/2" 4-1/2"
7 27 5/8"-11 1-3/4" 1-3/8" 2-1/2" 4-1/4" 4-7/8" 4-1/2"
8 28 3/4"-10 2" 1-1/2" 2-13/16" 4-13/16" 5-1/4" 5"
9 29 7/8"-9 2-1/4" 1-11/16" 3-1/4" 5-1/2" 6" 5"
10 30 1"-8 2-1/2" 1-13/16" 3-9/16" 6-1/16" 7" 5"
11 31 1-1/8"-7 2-3/4" 2" 4" 6-3/4" 7-1/2" 2-3/4"
12 32 1-1/4"-7 3" 2-3/16" 4-7/16" 7-7/16" 8-1/2" 3"
14 34 1-1/2"-6 3-1/2" 2-1/2" 5-3/16" 8-11/16" 9-1/2" 3-1/2"

Working load limits for eye bolts are based on a straight vertical lift in a gradually increasing manner.
Angular lifts will significantly lower working load limits (see Shoulder Pattern) and should be avoided
whenever possible. If an angular lift is required, a properly seated Shoulder Pattern eye bolt must be
used. Loads should always be applied to eye bolts in the plane of the eye, not at an angle to this plane.
Angular lifts must never be more than a 45° pull. For angular lifting see page 23.

Diameter Working Load Limit

and Straight 45° Pull (Y)
Thread Pull (X) Shoulder Only
1/4"-20 500 125
5/16"-18 900 225
3/8"-16 1400 350
7/16"-14 2000 500
1/2"-13 2600 650
9/16"-12 3200 750
5/8"-11 4000 1000
3/4"-10 6000 1500
7/8"-9 7000 1750
Plain Pattern Shoulder Pattern
1"-8 9000 2250
1-1/8"-7 12000 2500
1-1/4"-7 15000 3750
1-1/2"-6 21000 4900

ANGULAR LIFTS SHOULD BE AVOIDED WHENEVER POSSIBLE.

Made in U S A

18 Chicago Hardware and Fixture Company Since 1912

 MACHINERY EYE BOLTS
Drop forged steel. Heat treated after forging. Self-colored, zinc plated, or hot galvanized.
Plain or shoulder type, blank or threaded. Threaded will be supplied unless otherwise
specified. See additional specifications and dimensions on page 18.

STANDARD SHANK LENGTHS

PLAIN PATTERN Threaded Blank
Plain Bolt Standard Weight Weight
Part Part
Pattern Diameter Shank Per Per
No. No.
No. N.C. Length 100 100
1 1/4" 1" 11605 3 5 11005 1 5.5
2 5/16" 1-1/8" 11625 1 10.5 11025 9 11.5
3 3/8" 1-1/4" 11645 9 15.5 11045 7 16.5
4 7/16" 1-3/8" 11665 7 20.5 11065 5 22
5 1/2" 1-1/2" 11685 5 33 11085 3 35
6 9/16" 1-5/8" 11705 0 44.5 11105 8 45
7 5/8" 1-3/4" 11725 8 64 11125 6 66
8 3/4" 2" 11748 7 90.5 11148 5 97
9 7/8" 2-1/4" 11768 5 135 11168 3 142
Available in Zinc 10 1" 2-1/2" 11788 3 190.5 11188 1 199
Plated and Hot 11 1-1/8" 2-3/4" 11808 8 299.5 11208 6 312
Galvanized.
12 1-1/4" 3" 11831 6 399 11231 4 412
See page 20.
14 1-1/2" 3-1/2" 11851 4 662.5 11251 2 691

Some sizes
available in Made in U S A
Stainless Steel.
See page 48.

Available in Metric
See page 22. STANDARD SHANK LENGTHS
SHOULDER PATTERN Threaded Blank
Shoulder Bolt Standard Weight Weight
Part Part
Pattern Diameter Shank Per Per
No. No.
No. N.C. Length 100 100
21 1/4" 1" 12805 6 6 12205 4 6
22 5/16" 1-1/8" 12825 4 10 12225 2 10.5
23 3/8" 1-1/4" 12845 2 16 12245 0 17
24 7/16" 1-3/8" 12865 0 26.5 12265 8 28
25 1/2" 1-1/2" 12885 8 38 12285 6 39
26 9/16" 1-5/8" 12905 3 49 12305 1 52.5
27 5/8" 1-3/4" 12925 1 73.5 12325 9 76.5
28 3/4" 2" 12948 0 99.5 12348 8 104
29 7/8" 2-1/4" 12968 8 172.5 12368 6 178
30 1" 2-1/2" 12988 6 235 12388 4 242
31 1-1/8" 2-3/4" 13008 0 342.5 12408 9 347
32 1-1/4" 3" 13031 8 462.5 12431 7 485
34 1-1/2" 3-1/2" 13051 6 752.5 12451 5 780

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 19

 PLATED MACHINERY EYE BOLTS

ZINC PLATED
PLAIN PATTERN – ZINC SHOULDER PATTERN – ZINC
Plain Bolt Standard Shoulder Bolt Standard
Part Part
Pattern Diameter Shank Pattern Diameter Shank
No. No.
No. N.C. Length No. N.C. Length
1 1/4" 1" 26005 3 21 1/4" 1" 26050 3
2 5/16" 1-1/8" 26008 4 22 5/16" 1-1/8" 26053 4
3 3/8" 1-1/4" 26011 4 23 3/8" 1-1/4" 26056 5
4 7/16" 1-3/8" 26014 5 24 7/16" 1-3/8" 26059 6
5 1/2" 1-1/2" 26017 6 25 1/2" 1-1/2" 26062 6
6 9/16" 1-5/8" 26020 6 26 9/16" 1-5/8" 26065 7
7 5/8" 1-3/4" 26023 7 27 5/8" 1-3/4" 26068 8
8 3/4" 2" 26026 8 28 3/4" 2" 26071 8
9 7/8" 2-1/4" 26029 9 29 7/8" 2-1/4" 26074 9
10 1" 2-1/2" 26032 9 30 1" 2-1/2" 26077 0
11 1-1/8" 2-3/4" 26035 0 31 1-1/8" 2-3/4" 26080 0
12 1-1/4" 3" 26038 1 32 1-1/4" 3" 26083 1
14 1-1/2" 3-1/2" 26041 1 34 1-1/2" 3-1/2" 26086 2

Made in U S A

HOT GALVANIZED

PLAIN PATTERN – GALVANIZED SHOULDER PATTERN – GALVANIZED

Plain Bolt Standard Shoulder Bolt Standard
Part Part
Pattern Diameter Shank Pattern Diameter Shank
No. No.
No. N.C. Length No. N.C. Length
1 1/4" 1" 26105 0 21 1/4" 1" 26155 5
2 5/16" 1-1/8" 26108 1 22 5/16" 1-1/8" 26158 6
3 3/8" 1-1/4" 26111 1 23 3/8" 1-1/4" 26161 6
4 7/16" 1-3/8" 26114 2 24 7/16" 1-3/8" 26164 7
5 1/2" 1-1/2" 26117 3 25 1/2" 1-1/2" 26167 8
6 9/16" 1-5/8" 26120 3 26 9/16" 1-5/8" 26170 8
7 5/8" 1-3/4" 26123 4 27 5/8" 1-3/4" 26173 9
8 3/4" 2" 26126 5 28 3/4" 2" 26176 0
9 7/8" 2-1/4" 26129 6 29 7/8" 2-1/4" 26179 1
10 1" 2-1/2" 26132 6 30 1" 2-1/2" 26182 1
11 1-1/8" 2-3/4" 26135 7 31 1-1/8" 2-3/4" 26185 2
12 1-1/4" 3" 26138 8 32 1-1/4" 3" 26188 3
14 1-1/2" 3-1/2" 26141 8 34 1-1/2" 3-1/2" 26191 3

20 Chicago Hardware and Fixture Company Since 1912

 MACHINERY EYE BOLTS
Variation in quantity: on special items we reserve the right to a maximum 10% variation
for allowances in manufacture.

SPECIAL SHANK LENGTHS SPECIAL SHANK LENGTHS

PLAIN PATTERN SHOULDER PATTERN
Threaded Blank Threaded Blank
Bolt Special Weight Weight Bolt Special Weight Weight
Part Part Part Part
Diameter Shank Per Per Diameter Shank Per Per
No. No. No. No.
N.C. Length 100 100 N.C. Length 100 100
1/4" 2" 11608 4 6 11008 2 8 1/4" 2" 12808 7 8 12208 5 10
1/4" 3" 11611 4 10 11011 2 14 1/4" 3" 12811 7 10 12211 5 12
5/16" 2" 11628 2 12 11028 0 14 5/16" 2" 12828 5 12 12228 3 14
5/16" 3" 11631 2 14 11031 0 16 5/16" 3" 12831 5 14 12231 3 16
5/16" 4" 11634 3 14 11034 1 18 5/16" 4" 12834 6 16 12234 4 18
3/8" 2" 11648 0 16 11048 8 18 3/8" 2" 12848 3 20 12248 1 22
3/8" 3" 11651 0 18 11051 8 23 3/8" 3" 12851 3 22 12251 1 24
3/8" 4" 11654 1 22 11054 9 24 3/8" 4" 12854 4 24 12254 2 28
3/8" 4-1/2" 11657 2 22 11057 0 26 3/8" 4-1/2" 12857 5 26 12257 3 28
7/16" 2" 11668 8 22 11068 6 24 7/16" 2" 12868 1 26 12268 9 30
7/16" 3" 11671 8 26 11071 6 30 7/16" 3" 12871 1 30 12271 9 32
7/16" 4" 11674 9 30 11074 7 34 7/16" 4" 12874 2 34 12274 0 36
7/16" 4-1/2" 11677 0 30 11077 8 36 7/16" 4-1/2" 12877 3 36 12277 1 38
1/2" 2" 11688 6 32 11088 4 34 1/2" 2" 12888 9 40 12288 7 42
1/2" 3" 11691 6 38 11091 4 42 1/2" 3" 12891 9 44 12291 7 46
1/2" 4" 11694 7 42 11094 5 48 1/2" 4" 12894 0 46 12294 8 50
1/2" 4-1/2" 11697 8 42 11097 6 50 1/2" 4-1/2" 12897 1 48 12297 9 52
9/16" 2" 11708 1 48 11108 9 52 9/16" 2" 12908 4 48 12308 2 52
9/16" 3" 11711 1 54 11111 9 60 9/16" 3" 12911 4 52 12311 2 58
9/16" 4" 11714 2 60 11114 0 68 9/16" 4" 12914 5 58 12314 3 60
9/16" 4-1/2" 11717 3 60 11117 1 68 9/16" 4-1/2" 12917 6 60 12317 4 68
5/8" 2" 11728 9 62 11128 7 68 5/8" 2" 12928 2 74 12328 0 80
5/8" 3" 11731 9 70 11131 7 74 5/8" 3" 12931 2 82 12331 0 86
5/8" 4" 11734 0 74 11134 8 86 5/8" 4" 12934 3 90 12334 1 102
5/8" 4-1/2" 11737 1 76 11137 9 90 5/8" 4-1/2" 12937 4 92 12337 2 104
3/4" 3" 11751 7 96 11151 5 120 3/4" 3" 12951 0 116 12351 8 126
3/4" 4" 11754 8 104 11154 6 126 3/4" 4" 12954 1 130 12354 9 140
3/4" 4-1/2" 11757 9 108 11157 7 144 3/4" 4-1/2" 12957 2 132 12357 0 146
3/4" 5" 11760 9 132 11160 7 154 3/4" 5" 12960 2 138 12360 0 154
7/8" 3" 11771 5 188 11171 3 196 7/8" 3" 12971 8 186 12371 6 198
7/8" 4" 11774 6 202 11174 4 218 7/8" 4" 12974 9 202 12374 7 218
7/8" 4-1/2" 11777 7 210 11177 5 224 7/8" 4-1/2" 12977 0 208 12377 8 226
7/8" 5" 11780 7 218 11180 5 230 7/8" 5" 12980 0 216 12380 8 232
1" 3" 11791 3 210 11191 1 232 1" 3" 12991 6 254 12391 4 270
1" 4" 11794 4 230 11194 2 254 1" 4" 12994 7 266 12394 5 290
1" 4-1/2" 11797 5 236 11197 3 264 1" 4-1/2" 12997 8 280 12397 6 304
1" 5" 11800 2 254 11200 0 276 1" 5" 13000 4 290 12400 3 318

See page 18 for specifications and dimensions.

Additional special shank lengths available upon request.

Made in U S A

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 21

 METRIC MACHINERY EYE BOLTS
Made in U S A
Dimensions in Millimeters – Some Sizes Available
in Stainless Steel on a Special Basis.

FORGED • CARBON STEEL • SELF-COLORED • SHOULDER PATTERN

Approx. A B C Approx. Wt. Working Working
Part Metric
Equivalent Thread Shank I.D. Per 100 Pcs. Load Limit Load Limit
No. Size
in Inches Size Length, mm Eye, mm in Lbs. in Kgs. in Lbs.
13805 5 M6 1/4" M6 x 1.0 25.4 19 6 210 462
13825 3 M7 5/16" M7 x 1.0 28.5 22 10 370 814
13845 1 M8 3/8" M8 x 1.25 31.7 25 16 450 992
13865 9 M10 7/16" M10 x 1.5 35.0 28 21 740 1,628
13885 7 M12 1/2" M12 x 1.75 38.0 30 38 1,030 2,266
13905 2 M14 9/16" M14 x 2.0 44.5 35 73 1,600 3,520
13925 0 M16 5/8" M16 x 2.0 44.5 35 73 1,600 3,520
13948 9 M18 3/4" M18 x 2.5 51.0 38 104 2,140 4,708
13968 7 M20 7/8" M20 x 2.5 57.0 43 161 2,860 6,292
13988 5 M24 1" M24 x 3.0 63.5 46 231 3,850 8,470
14008 9 M27 1-1/8" M27 x 3.0 70.0 51 335 5,200 11,440
14031 7 M30 1-1/4" M30 x 3.5 76.0 55 439 6,400 14,080
14051 5 M36 1-1/2" M36 x 4.0 89.0 63 731 8,970 19,734

DROP FORGED LIFTING EYES

Drop forged from C-1035 steel, heat treated. Available blank or threaded. Self-colored finish is
standard; hot galvanized or other finishes supplied on a special basis. Used in lifting Made in U S A
applications where larger eyes are required. When ordering prefix stock number with letter
“B” (blank) or “T” (threaded) as required. Loads are based on a safety factor of 5 to 1. Working
loading limits for lifting eyes are based on a straight vertical lift in a gradually increasing
manner, and should never be used for angular lifts.

LIFTING EYES – SELF-COLORED

Threaded
Stock Bail Blank Threaded
Working
Number Size Part No. Part No.
Load Limit
C-186 1/4" 15005 7 15505 2 860
C-187 5/16" 15010 1 15510 6 1260
C-185 3/8" 15015 6 15515 1 2200
C-181 1/2" 15020 0 15520 5 3600
C-184 5/8" 15025 5 15525 0 5200
C-188 3/4" 15030 9 15530 4 7000

Stock Shank Dimensions – Inches Thread Weight Per 100

Number H L A C B E F G S R Length Blank Threaded
C-186 5/16" 1" 1-1/4" 3/4" 1-1/16" 19/32" 1/2" 3/8" 1/4" 2-11/16" 7/8" 12 11
C-187 3/8" 1-1/8" 1-5/8" 1" 1-1/4" 3/4" 9/16" 1/2" 5/16" 3-3/16" 1" 22 22
C-185 1/2" 1-1/4" 2" 1-1/4" 1-1/2" 1" 13/16" 5/8" 3/8" 3-3/4" 1-1/8" 41 38
C-181 5/8" 1-1/2" 2-1/2" 1-1/2" 2" 1-3/16" 1" 11/16" 1/2" 4-11/16" 1-3/8" 81 74
C-184 3/4" 1-7/8" 3" 1-3/4" 2-3/8" 1-3/8" 1-1/8" 7/8" 5/8" 5-3/4" 1-3/4" 139 129
C-188 7/8" 2" 3-1/2" 2" 2-5/8" 1-5/8" 1-5/16" 15/16" 3/4" 6-5/16" 1-7/8" 222 214

22 Chicago Hardware and Fixture Company Since 1912

 ALLOY STEEL SWIVEL HOIST RINGS

NEW!

Chicago Hardware is proud to announce the addition of Center Pull Style Swivel Hoist Rings to its product
line. This is the ideal product for angular lift applications. These Swivel Hoist Rings have full swivel and
pivot action.

Our hoist rings are alloy steel with a black oxide finish. They adhere to the same rigid quality standards
that have been a part of Chicago Hardware's proud tradition since 1912. Individually proof tested and
magnetic particle inspected. From 800 to 24,000 lb load capacities (Rated at 5:1 safety factor).

Part Thread Working Thread

B D E F G H Torque
No. Size (A) Load Limit Length (C)
86004 8 5/16"-18 800 9/16" 2.67" 0.75" 0.43" 0.38" 1.84" 1-1/4" 7
86007 9 3/8"-16 1000 9/16" 2.67" 0.75" 0.43" 0.38" 1.84" 1-1/4" 12
86013 0 1/2"-13 2500 3/4" 4.78" 1.5" 0.88" 0.75" 3.52" 2-3/8" 28
86016 1 1/2"-13 2500 1" 4.78" 1.5" 0.88" 0.75" 3.52" 2-3/8" 28
86019 2 1/2"-13 2500 1-1/4" 4.78" 1.5" 0.88" 0.75" 3.52" 2-3/8" 28
86022 2 5/8"-11 4000 1" 4.78" 1.5" 0.88" 0.75" 3.52" 2-1/4" 60
86025 3 5/8"-11 4000 1-1/4" 4.78" 1.5" 0.88" 0.75" 3.52" 2-1/4" 60
86028 4 3/4"-10 5000 1" 4.78" 1.5" 0.88" 0.75" 3.52" 2-1/8" 100
86031 4 3/4"-10 5000 1-1/2" 4.78" 1.5" 0.88" 0.75" 3.52" 2-1/8" 100
86034 5 3/4"-10 7000 1" 6.52" 2.31" 1.4" 1" 5.14" 2-15/16" 100
86037 6 3/4"-10 7000 1-1/2" 6.52" 2.31" 1.4" 1" 5.14" 2-15/16" 100
86043 7 7/8"-9 8000 1-1/4" 6.52" 2.31" 1.4" 1" 5.14" 2-13/16" 160
86046 8 1"-8 10000 1-1/4" 6.52" 2.31" 1.4" 1" 5.14" 2-11/16" 230
86049 9 1"-8 10000 1-1/2" 6.52" 2.31" 1.4" 1" 5.14" 2-11/16" 230
86052 9 1"-8 10000 2-1/4" 6.52" 2.31" 1.4" 1" 5.14" 2-11/16" 230
86055 0 1-1/4"-7 15000 1-7/8" 8.73" 3.19" 1.75" 1.25" 6.5" 4-1/4" 470
86061 1 1-1/2"-6 24000 2-3/4" 12.47" 4.19" 2.25" 1.75" 8.55" 6-1/2" 800

WARNING: DO NOT EXCEED SAFE WORK LOAD

Made in U S A

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 23

 DROP FORGED HOOKS
Hooks are drop forged steel and heat treated. Latch, spring, machine screw and
nut are stainless steel. These hooks are also available without the latch kit.

SAFETY Self-Colored Galvanized EYE Self-Colored Galvanized

Working Load Working Load
Stock No. Part No. Part No. Stock No. Part No. Part No.
Limit in Tons Limit in Tons
22 3/4 22605 9 22655 4 22 3/4 22705 6 22755 1
23 1 22610 3 22660 8 23 1 22710 0 22760 5
24 1-1/2 22615 8 22665 3 24 1-1/2 22715 5 22765 0
25 2 22620 2 22670 7 25 2 22720 9 22770 4
26 3 22625 7 22675 2 26 3 22725 4 22775 9

SPECIFICATIONS
Stock Dimensions – Inches Weight Working Load
Number A B C D E L Per 100 Limit (Tons)
22 1-1/2" 3/4" 13/16" 2-7/8" 3-1/4" 4-3/8" 59.5 3/4
23 1-3/4" 7/8" 29/32" 3-3/16" 3-23/32" 4-31/32" 87 1
24 2" 1" 27/32" 3-15/32" 4" 5-13/32" 113.5 1-1/2
25 2-1/4" 1-1/8" 1-1/8" 4-1/16" 4-5/8" 6-5/16" 169.5 2
26 2-1/2" 1-1/4" 1-5/32" 4-1/2" 4-31/32" 6-27/32" 258.5 3

Made in U S A

Stainless
LATCH KITS Steel
Hook Part No.
Working Load Per
Stock No. Set
Limit in Tons
22 3/4 25105 1
23 1 25105 1
24 1-1/2 25110 5
25 2 25115 0
26 3 25115 0

24 Chicago Hardware and Fixture Company Since 1912

DROP FORGED HIGH-TEST CHAIN HOOKS
Made in U S A

• Made for use on High-Test Chain. All

hooks are heat treated. Also can be
used on BBB and proof coil.

• High Test stamped on every hook.

• Available Self-Colored and Zinc Plated.

CLEVIS GRAB HOOKS / DROP FORGED HIGH-TEST Self- Zinc

Colored Plated
Working Weight
Chain
Load Limit A B C D E F Per 100 Part No. Part No.
Size
in Pounds in Pounds
1/4" 2600 5/16" 1-15/16" 3/8" 3-3/8" 5/16" 2" 31.5 23705 5 23805 2
5/16" 4000 3/8" 2-1/4" 7/16" 3-15/16" 3/8" 2-3/8" 58.5 23710 9 23810 6
3/8" 5400 7/16" 2-11/16" 1/2" 4-1/2" 7/16" 2-11/16" 93.5 23715 4 23815 1
7/16" 7200 1/2" 3" 9/16" 5-1/32" 1/2" 3" 147 23720 8 23820 5
1/2" 9200 19/32" 3-5/16" 21/32" 5-5/8" 9/16" 3-23/64" 184 23725 3 23825 0
5/8" 11500 3/4" 4-1/4" 25/32" 6-7/8" 11/16" 4" 370 23730 7 23830 4
3/4" 16200 7/8" 5-1/4" 15/16" 8" 3/4" 4-19/32" 604 23735 2 23835 9

DROP FORGED SAFETY SNAP HOOKS

• Hooks are drop forged steel and heat

treated.
Made in U S A
• Latch, spring, machine screw and nut
are stainless steel.

• Vertical loads are based on a safety

factor of 5 to 1.

HEAT TREATED SAFETY SNAP HOOKS Self-Colored Galvanized

Working
Throat Overall Est. Wt.
Hook Size Load Limit I.D. Eye Part No. Part No.
Opening Length Per 100
in Pounds
7/16" 750 Lbs. 3/4" 3/4" 3-15/16" 28.8 Lbs. 22905 0 22955 5
9/16" 1000 Lbs. 1-1/8" 13/16" 4-3/4" 57.6 Lbs. 22910 4 22960 9

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 25

 DROP FORGED SWIVELS
Drop forged steel – all threaded components are heat treated. All swivels are hot galvanized.
Jaws (jaw and eye type) supplied with flat head pin and cotter. Vertical loads are based on
a safety factor of 5 to 1.

EYE AND EYE

Part Dimensions – Inches Working Load Weight
No. Size A B C D M R Limit (Tons) Per 100
21505 3 1/4" 1-1/4" 5/8" 3/4" 1-1/16" 5/16" 2-15/16" .43 20.2
21510 7 5/16" 1-5/8" 3/4" 1" 1-1/4" 3/8" 3-9/16" .63 36.5
21515 2 3/8" 2" 7/8" 1-1/4" 1-1/2" 1/2" 4-5/16" 1.1 70
21520 6 1/2" 2-1/2" 1-3/16" 1-1/2" 2" 5/8" 5-3/8" 1.8 141
21525 1 5/8" 3" 1-1/2" 1-3/4" 2-3/8" 3/4" 6-5/8" 2.6 249.5
21530 5 3/4" 3-1/2" 1-5/8" 2" 2-5/8" 7/8" 7-3/8" 3.5 413.5

CHAIN
Part Dimensions – Inches Working Load Weight
No. Size A B C D E R Limit (Tons) Per 100
21705 7 1/4" 1-1/4" 5/8" 3/4" 1/2" 1" 2-7/16" .26 14
21710 1 5/16" 1-5/8" 3/4" 1" 5/8" 1-1/4" 2-15/16" .46 27
21715 6 3/8" 2" 7/8" 1-1/4" 3/4" 1-1/2" 3-9/16" .62 47.5
21720 0 1/2" 2-1/2" 1-1/4" 1-1/2" 1" 2" 4-9/16" 1.1 100
21725 5 5/8" 3" 1-9/16" 1-3/4" 1-1/4" 2-5/16" 5-5/8" 1.6 169
21730 9 3/4" 3-1/2" 1-3/4" 2" 1-1/2" 2-3/4" 6-1/8" 2.0 268

JAW AND EYE

Part Dimensions – Inches Working Load Weight
No. Size A B C N K P R Limit (Tons) Per 100
21605 0 1/4" 1-1/4" 5/8" 3/4" 25/32" 15/32" 1/4" 2-1/2" .43 18.5
21610 4 5/16" 1-5/8" 3/4" 1" 27/32" 1/2" 5/16" 2-7/8" .63 35
21615 9 3/8" 2" 7/8" 1-1/4" 1-1/16" 5/8" 7/16" 3-1/2" 1.1 67.5
21620 3 1/2" 2-1/2" 1-1/4" 1-1/2" 1-15/32" 7/8" 1/2" 4-9/16" 1.8 131
21625 8 5/8" 3" 1-9/16" 1-3/4" 1-17/32" 1" 5/8" 5-5/16" 2.6 240
21630 2 3/4" 3-1/2" 1-3/4" 2" 1-3/4" 1-1/8" 3/4" 6" 3.5 360

SAFETY SWIVEL HOOKS

Drop forged steel. Hook is heat treated. Latch, spring, machine screw and nut are
stainless steel.

Part Dimensions – Inches Working Load Weight

No. A B C D F L R S Limit (Tons) Per 100
21905 1 2" 15/16" 1-1/4" 2-7/8" 7/8" 5-9/16" 4-15/32" 3/8" .75 91
21910 5 2-1/2" 1-5/16" 1-1/2" 3-3/16" 31/32" 6-5/8" 5-9/32" 1/2" 1 148

Made in U S A

26 Chicago Hardware and Fixture Company Since 1912

 DROP FORGED PAD EYES
DROP FORGED PAD EYES
Dimensions – Inches Weight
Stock Part Eye Shoulder *Overall Per 100
No. No. I.D. O.D. O.D. *Thickness Height in Lbs.
C-351 22005 7 1/4" 5/8" 5/8" 3/32" 3/4" 3.3
C-350 22010 1 3/4" 1-1/2" 1-1/16" 3/16" 1-5/8" 18.6
C-155 22015 6 1-3/16" 2-1/16" 1-11/16" 3/16" 2-3/8" 49
C-169 22020 0 1-1/4" 2-3/8" 2" 3/16" 2-7/8" 81

• Forged from carbon steel suitable for welding. Made in U S A

• Supplied with self-colored finish.
• *Not including draft.

DROP FORGED EYE NUTS

Stock Eye Nuts listed below, other than Blanks, are drilled and tapped
standard regardless of finish. Both types drilled only, with special tapping
or finish supplied to specification. Loads are based on a safety factor of 5
to 1. Blanks are self-colored.

NOTE: Loads shown apply to Eye Nuts only, based on a vertical pull, and
not to any connecting bolt or stud.

Regular
REGULAR EYE NUTS Blank Drilled & Tapped
Self-Colored Self-Colored Hot Galvanized
Stock No. Bail Size Tap Size
Part No. Part No. Part No.
C-186A 1/4" 1/4"-20 16005 6 16255 5 16755 5
C-186B 1/4" 5/16"-18 16010 0 16260 9 16760 9
C-187A 5/16" 3/8"-16 16015 5 16265 4 16765 9
C-185B 3/8" 7/16"-14 16020 9 16270 8 16770 8
C-185A 3/8" 1/2"-13 16025 4 16275 3 16775 8
C-181A 1/2" 5/8"-11 16030 8 16280 7 16780 2

Made in U S A C-184A 5/8" 3/4"-10 16035 3 16285 2 16785 7

C-188A 3/4" 7/8"-9 16040 7 16290 6 16790 1
C-188B 3/4" 1"-8 16045 2 16295 1 16795 6

Some sizes also available in Stainless Steel. See page 48.

SPECIFICATIONS
Stock Tap Sizes Dimensions – Inches Working Load Drilled & Tapped Blank
No. Std. M Max. N A C D E F S T Limit (Tons) Wgt. Per 100 Wgt. Per 100
C-186A 1/4"-20 3/8" 1-1/4" 3/4" 1-1/16" 19/32" 1/2" 1/4" 1-11/16" .26 8.2 9
C-186B 5/16"-18 3/8" 1-1/4" 3/4" 1-1/16" 19/32" 1/2" 1/4" 1-11/16" .42 8 9
C-187A 3/8"-16 7/16" 1-5/8" 1" 1-1/4" 3/4" 9/16" 5/16" 2-1/16" .62 15.7 16
C-185B 7/16"-14 1/2" 2" 1-1/4" 1-1/2" 1" 13/16" 3/8" 2-1/2" .85 29.7 31
C-185A 1/2"-13 1/2" 2" 1-1/4" 1-1/2" 1" 13/16" 3/8" 2-1/2" 1.12 29.3 31
C-181A 5/8"-11 3/4" 2-1/2" 1-1/2" 2" 1-3/16" 1" 1/2" 3-3/16" 1.8 61.5 66
C-184A 3/4"-10 7/8" 3" 1-3/4" 2-3/8" 1-3/8" 1-1/8" 5/8" 3-7/8" 2.6 103 112
C-188A 7/8"-9 1" 3-1/2" 2" 2-5/8" 1-5/8" 1-5/16" 3/4" 4-5/16" 3.6 163 183
C-188B 1"-8 1" 3-1/2" 2" 2-5/8" 1-5/8" 1-5/16" 3/4" 4-5/16" 3.6 161 183

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 27

 DROP FORGED HEAVY DUTY EYE NUTS
Stock Eye Nuts listed below, other than Blanks, are drilled and tapped standard regardless
of finish. Both types drilled only, with special tapping or finish supplied to specification.
Loads are based on a safety factor of 5 to 1. Self-colored finish is standard.

NOTE: Loads shown apply to Eye Nuts only, based on a vertical pull, and not to any
connecting bolt or stud.
Made in U S A
SELF-COLORED – BLANK OR DRILLED AND TAPPED
Blank Drilled & Tapped
Stock No. Bail Size Part No. Tap Size Part No.
100 5/16" 17005 5 3/8"-16 17255 4
101 7/16" 17010 9 1/2"-13 17260 8
102 9/16" 17015 4 5/8"-11 17265 3
103 3/4" 17020 8 3/4"-10 17270 7
104 7/8" 17025 3 7/8"-9 17275 2
105 1" 17030 7 1"-8 17280 6
105A 1" 17035 2 1-1/8"-7 17285 1 Blank
106 1-1/4" 17040 6 1-1/4"-7 17290 5
107 1-3/8" 17045 1 1-1/2"-6 17295 0 Drilled & Tapped

SPECIFICATIONS
Stock Dimensions – Inches Working Load Drilled & Tapped Blank
No. C S D M F E G H T Limit (Tons) Wgt. Per 100 Wgt. Per 100
100 7/8" 5/16" 5/16" 3/8-16" 3/4" 3/4" 3/4" 3/4" 2-1/4" .9 15 16
101 1-1/8" 7/16" 7/16" 1/2-13" 1" 1" 1" 1" 3" 1.8 37.5 43
102 1-3/8" 9/16" 9/16" 5/8-11" 1-1/4" 1-1/4" 1-1/4" 1-1/4" 3-3/4" 2.9 82.5 94
103 1-1/2" 3/4" 3/4" 3/4-10" 1-3/4" 1-1/4" 1-1/8" 1-1/2" 3-7/8" 5.3 145 160
104 1-5/8" 7/8" 7/8" 7/8-9" 2" 1-1/4" 1" 1-11/16" 3-15/16" 7.2 202.5 210
105 1-3/4" 1" 1" 1-8" 2-1/4" 1-5/8" 1-1/4" 1-7/8" 4-3/4" 9.4 327.5 340
105A 1-3/4" 1" 1" 1-1/8-7" 2-1/4" 1-5/8" 1-1/4" 1-7/8" 4-3/4" 11.3 297 340
106 2" 1-1/4" 1-1/4" 1-1/4-7" 2-7/8" 1-7/8" 1-3/8" 2-1/4" 5-1/2" 14.7 550 623
107 2-1/2" 1-3/8" 1-3/8" 1-1/2-6" 3-1/8" 2-1/8" 1-3/4" 2-5/8" 6-1/2" 17.8 807.5 919

CLEVIS PINS – HEAT TREATED

SELF-COLORED OR HOT GALVANIZED

Self- Hot Dimensions in Inches
Colored Galvanized Lengths Head Hole Weight
Part Part Shank Under Per 100
Overall O.D. Thickness I.D. *Center
No. No. Diameter Head In Lbs.
19005 3 19105 0 1/4" 1-1/4" 1-1/8" 7/16" 1/8" 7/64" 1-1/32" 1.9
19010 7 19110 4 5/16" 1-1/2" 1-3/8" 1/2" 1/8" 7/64" 1-1/4" 3.4
19015 2 19115 9 3/8" 1-11/16" 1-1/2" 9/16" 3/16" 1/8" 1-11/32" 5.7
19020 6 19120 3 7/16" 1-11/16" 1-1/2" 3/4" 3/16" 1/8" 1-23/64" 8.4
19025 1 19125 8 7/16" 1-15/16" 1-3/4" 3/4" 3/16" 1/8" 1-5/8" 9.5
19030 5 19130 2 1/2" 2-5/32" 1-15/16" 13/16" 7/32" 1/8" 1-13/16" 13.3
19035 0 19135 7 5/8" 2-17/32" 2-5/16" 1-1/32" 7/32" 5/32" 2-5/32" 24
19040 4 19140 1 3/4" 3" 2-3/4" 1-3/16" 1/4" 3/16" 2-9/16" 40

Made in U S A 19045 9 19145 6 7/8" 3-1/2" 3-1/4" 1-1/4" 1/4" 13/64" 3" 62
19050 3 19150 0 1" 4-5/32" 3-25/32" 1-7/16" 3/8" 13/64" 3-17/32" 96
19055 8 19155 5 1-1/8" 4-5/8" 4-1/4" 1-5/8" 3/8" 13/64" 3-15/16" 134

*From under head

28 Chicago Hardware and Fixture Company Since 1912
 DROP FORGED BLANK ROD ENDS
Drop forged. Listed diameters and lengths carried in stock blank, self-colored. Drilling,
threading, other machining and plating furnished to specification.
NOTE: Average properties of 1035 natural hot rolled steel 75/85,000 lbs. P.S.I. tensile,
40/55,000 lbs. P.S.I yield.
DROP FORGED BLANK ROD ENDS
Made in U S A Dimensions – Inches
Stock Part Weight
Shank Boss Boss *Length (A) in
No. No. Per 100
Diameter (B) Diameter (C) Thickness (F) Inches
C-134 18005 4 1/4" 1/2" 9/32" 3" 6.1
C-134-A 18010 8 1/4" 1/2" 9/32" 6" 11
C-135 18015 3 5/16" 5/8" 11/32" 3" 9.5
C-135-A 18020 7 5/16" 5/8" 11/32" 6" 18
C-163-A 18025 2 3/8" 11/16" 3/8" 2-1/8" 12
C-162 18030 6 3/8" 3/4" 3/8" 2-1/2" 12.5
C-217 18035 1 3/8" 3/4" 7/16" 3" 14
C-136 18040 5 3/8" 3/4" 7/16" 6" 25.5
C-137 18045 0 7/16" 7/8" 1/2" 6" 35
C-245 18050 4 1/2" 15/16" 9/16" 1-3/4" 22
C-163 18055 9 1/2" 15/16" 9/16" 3-1/8" 27.5
C-212 18060 3 1/2" 1" 9/16" 3-1/2" 30
C-138 18065 8 1/2" 1" 9/16" 6" 47
C-195 18070 2 1/2" 1" 9/16" 10" 70
C-189 18075 7 5/8" 1-1/4" 11/16" 3" 45.5
C-303 18080 1 5/8" 1-3/16" 5/8" 3-1/2" 48
C-139 18085 6 5/8" 1-1/4" 11/16" 6" 77.5
C-172 18090 0 5/8" 1-1/4" 11/16" 8" 92
C-196 18095 5 5/8" 1-1/4" 11/16" 10" 119
C-216 18100 6 3/4" 1-1/2" 13/16" 3-1/2" 82
C-140 18105 1 3/4" 1-1/2" 13/16" 6" 112
C-197 18110 5 3/4" 1-1/2" 13/16" 10" 163.5
C-141 18115 0 7/8" 1-3/4" 15/16" 6" 164
Some sizes also C-211 18120 4 7/8" 1-3/4" 15/16" 12" 377
available in Stainless C-142 18125 9 1" 2" 1-1/16" 6" 216
Steel. See page 48. C-142-A 18130 3 1" 2" 1-1/16" 12" 354
C-282 18135 8 1-1/4" 2-1/2" 1-5/16" 12" 595

BLACK OXIDE MACHINED ROD ENDS

(MADE IN USA)
Dimensions – Inches
Weight Per
Part No. Thread Pitch Length in Inches
Thread Length (T) Hole I.D. (G) Boss Diameter (C) Boss Thickness (F) 100
(A)*
18205 8 1/4"-20 2" 3/4" 3/16" 1/2" 9/32" 4
18210 2 5/16"-18 3" 1-1/2" 5/16" 5/8" 11/32" 8
18215 7 3/8"-16 3" 1-1/2" 5/16" 3/4" 7/16" 12
18220 1 3/8"-16 3" 1-1/2" 3/8" 3/4" 7/16" 12
18225 6 3/8"-16 3-3/4" 2" 3/8" 3/4" 7/16" 14
18230 0 3/8"-16 4" 1-1/2" 3/8" 3/4" 7/16" 16
18235 5 3/8"-16 5" 2-1/2" 3/8" 3/4" 7/16" 18
18245 4 1/2"-13 3-3/4" 1-1/2" 3/8" 1" 9/16" 29
18250 8 1/2"-13 4" 1-1/2" 3/8" 1" 9/16" 30
18240 9 1/2"-13 5" 1-1/2" 3/8" 1" 9/16" 36
18255 3 1/2"-13 5" 2" 3/8" 1" 9/16" 36
18260 7 5/8"-11 4-1/2" 2" 5/8" 1-1/4" 11/16" 50
18265 2 5/8"-11 5" 1-3/4" 5/8" 1-1/4" 11/16" 55
18270 6 5/8"-11 6" 2-1/2" 5/8" 1-1/4" 11/16" 63
18280 5 3/4"-10 4-1/2" 2" 3/4" 1-1/2" 13/16" 77
18275 1 3/4"-10 6" 2-1/2" 3/4" 1-1/2" 13/16" 95
* Measured from center of boss

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 29

 DROP FORGED YOKE ENDS
SELF-COLORED DROP FORGED YOKE ENDS

ADJUSTABLE
Stock Part "T" Tap Dimensions in Inches – Machined Est. Wt.
No. No. Size A B C D E F G H K Per 100 Pcs.
51 19505 8 1/4"-28 2" 7/16" 7/16" 1-1/4" 9/32" 5/8" 1/4" 3/4" 1/2" 7.5 Lbs.
52 19510 2 5/16"-24 2-1/4" 1/2" 1/2" 1-7/16" 11/32" 3/4" 5/16" 13/16" 19/32" 10.7 Lbs.
53 19515 7 3/8"-24 2-1/2" 5/8" 5/8" 1-5/8" 7/16" 7/8" 3/8" 7/8" 11/16" 16 Lbs.
54 19520 1 7/16"-20 2-7/8" 23/32" 23/32" 1-7/8" 1/2" 1" 7/16" 1" 13/16" 24 Lbs.
55 19525 6 1/2"-20 3" 13/16" 13/16" 1-7/8" 9/16" 1-1/8" 1/2" 1-1/8" 15/16" 32.2 Lbs.
56 19530 0 5/8"-18 4-15/16" 1-1/16" 1-1/16" 3-11/16" 11/16" 1-3/8" 5/8" 1-1/4" 1-3/16" 80 Lbs.
57 19535 5 3/4"-16 6-1/16" 1-1/4" 1-1/4" 4-9/16" 13/16" 1-5/8" 3/4" 1-1/2" 1-7/16" 135 Lbs.

PLAIN TYPE
Stock Part Dimensions in Inches – Machined Est. Wt.
No. No. A B C D E F G H K U Per 100 Pcs.
61 19705 2 1-3/4" 1/4" 1-19/32" 5/8" 9/32" 5/8" 1/4" 1-1/8" 1/2" 7/16" 4.7 Lbs.
62 19710 6 2" 5/16" 1-7/16" 3/4" 11/32" 3/4" 5/16" 1-1/4" 19/32" 1/2" 7.8 Lbs.
63 19715 1 2-1/8" 3/8" 1-33/64" 27/32" 7/16" 7/8" 3/8" 1-9/32" 11/16" 5/8" 11.1 Lbs.
64 19720 5 2-1/4" 7/16" 1-57/64" 1" 1/2" 1" 7/16" 1-1/4" 13/16" 23/32" 15.1 Lbs.
65 19725 0 2-1/2" 1/2" 1-11/16" 1-1/8" 9/16" 1-1/8" 1/2" 1-3/8" 15/16" 13/16" 23.1 Lbs.
66 19730 4 2-7/8" 5/8" 1-53/64" 1-7/16" 11/16" 1-3/8" 5/8" 1-7/16" 1-3/16" 1-1/16" 43 Lbs.
67 19735 9 3-5/8" 3/4" 2-25/64" 1-11/16" 13/16" 1-5/8" 3/4" 1-15/16" 1-7/16" 1-1/8" 75 Lbs.

SELF-COLORED SAE CLEVIS PINS FOR YOKE ENDS

Dimensions in Inches – Machined
Lengths Head Hole Weight
Part Shank Under Per 100
Diameter Overall O.D. Thickness I.D. *Center
No. Head in Lbs.
19305 4 1/4" 55/64" 49/64" 3/8" 3/32" 5/64" 43/64" 1.3
Produced
19310 8 5/16" 1-1/32" 15/16" 7/16" 3/32" 7/64" 13/16" 2.3
from 1018
19315 3 3/8" 1-3/16" 1-1/16" 1/2" 1/8" 7/64" 15/16" 3.7
cold heading
19320 7 7/16" 1-11/32" 1-3/16" 9/16" 5/32" 7/64" 1-1/16" 5.9
quality wire.
19330 6 1/2" 1-33/64" 1-23/64" 5/8" 5/32" 9/64" 1-13/64" 8.6
19335 1 5/8" 1-13/16" 1-39/64" 13/16" 13/64" 9/64" 1-29/64" 16.2
19340 5 3/4" 2-5/32" 1-29/32" 15/16" 1/4" 11/64" 1-23/32" 27.5

*From under head

Made in U S A

30 Chicago Hardware and Fixture Company Since 1912

 MALLEABLE BEVEL WASHERS
Bevelled 2" in 12" which is standard for flanges of beams and channels. Available in
self-colored or hot galvanized finish.

MALLEABLE BEVEL WASHERS

Bolt Black Hot Galvanized Dimensions – Inches Weight Per
Diameter Part No. Part No. A B C D 100 (Lbs.)
1/4" 06305 0 06355 5 11/16" 7/32" 5/64" 5/16" 2
5/16" 06308 1 06358 6 1" 5/16" 9/64" 3/8" 6
3/8" 06311 1 06361 6 1-1/4" 11/32" 5/32" 7/16" 9.3
1/2" 06314 2 06364 7 1-1/4" 11/32" 5/32" 9/16" 8.8
5/8" 06317 3 06367 8 1-1/2" 13/32" 5/32" 11/16" 12.4
3/4" 06320 3 06370 8 1-1/2" 15/32" 7/32" 13/16" 15
7/8" 06323 4 06373 9 2" 9/16" 7/32" 15/16" 34
1" 06326 5 06376 0 2" 9/16" 7/32" 1-3/32" 31.5
1-1/8" 06329 6 06379 1 2-1/4" 5/8" 9/32" 1-3/16" 43.5
1-1/4" 06332 6 06382 1 2-1/4" 23/32" 5/16" 1-11/32" 68.5

ZINC PLATED S-HOOKS

WARNING:
Made in U S A
Any deviations such as
angular lifts, shock loads,
modification of the “S” hook
will result in drastically
reduced working load limits.
ZINC PLATED S-HOOKS
Low carbon cold drawn steel wire. Supplied with blunt ends and zinc plated finish. Standard
Pack – 50 pieces. Other rust preventive coatings and self-colored (black) available on a special
basis. “S” Hooks also manufactured to specifications.

Dimensions – Inches Working

Stock Part Wire Overall Hooks Inside Opening Weight Per Load
No. No. Diameter Length Dia. Hooks 100 (Lbs.) Limit (Lbs.)
S-1 06105 6 .080" 3/4" 1/4" 1/8" .26 7
S-1A 06108 7 .105" 1" 5/16" 5/32" .55 16
S-2 06111 7 .114" 1-1/4" 3/8" 3/16" .83 17
S-2A 06114 8 .148" 1-1/2" 7/16" 7/32" 1.62 26
S-3 06117 9 .186" 1-3/4" 1/2" 1/4" 2.97 40
S-4 06120 9 .220" 2-1/8" 5/8" 5/16" 5.15 58
S-5 06123 0 .250" 2-1/2" 3/4" 7/16" 7.5 70
S-6 06126 1 .312" 3" 7/8" 1/2" 13.9 132
S-7 06129 2 .375" 3-1/2" 1" 1/2" 23.44 170

Some sizes available in stainless steel. See page 49.

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 31

 ROUND BEND U-BOLTS
Round Bend U-Bolts for Steel or
Wrought Iron pipe sizes 1/4"-18"
inclusive, as listed on this and next
pages, are produced from low carbon Standard Over 4"
Pack: Pipe Size:
Made in U S A steel and supplied with NC rolled
10 Pieces Bulk
threads and two (2) hex nuts. In
addition, U-Bolt plate is available if
required.

ZINC PLATED Some sizes also available in Stainless Steel. See page 50.
U-Bolt Dimensions – Inches For U-Bolts & 2 Nuts U-Bolts, Plates & 2 Nuts
Diameter I.D. Inside Thread Pipe Stock Part Weight Stock Part Weight
& Thread (A) (C) Length (B) Length (T) Size No. No. Per 100 No. No. Per 100
1/4"-20 9/16" 1-1/4" 3/4" 1/4" 01 50005 0 5 1 50205 4 7
1/4"-20 3/4" 1-1/4" 5/8" 3/8" 02 50008 1 5 2 50208 5 7
1/4"-20 3/4" 2-1/4" 1-1/2" 3/8" 03 50011 1 7 3 50211 5 9
1/4"-20 1" 1-3/4" 1" 1/2" 04 50014 2 7 4 50214 6 9
1/4"-20 1" 2-3/4" 1-1/4" 1/2" 04L 50017 3 8 4L 50217 7 11
1/4"-20 1-1/8" 2" 1" 3/4" 05 50020 3 7 5 50220 7 9
1/4"-20 1-1/8" 3-1/8" 1-1/2" 3/4" 05L 50023 4 9 5L 50223 8 12
1/4"-20 1-1/4" 2-1/4" 1-1/4" 3/4" 06 50026 5 7.5 6 50226 9 10
1/4"-20 1-1/2" 2-3/4" 1-3/8" 1" 07 50029 6 9 7 50229 0 12
1/4"-20 1-3/4" 3" 1-3/8" 1-1/4" 08 50032 6 9 8 50232 0 12
1/4"-20 2" 3-1/4" 1-3/8" 1-1/2" 09 50035 7 9.5 9 50235 1 14
5/16"-18 1" 2-3/16" 1-3/8" 1/2" 010 50038 8 11 10 50238 2 14
5/16"-18 1-1/8" 2-3/16" 1" 3/4" 0101 50041 8 12 101 50241 2 14.5
5/16"-18 1-3/8" 2-3/16" 1" 1" 011 50044 9 12 11 50244 3 15
5/16"-18 1-3/8" 3-5/8" 2" 1" 011L 50047 0 16 11L 50247 4 20
5/16"-18 1-1/2" 2-3/16" 1" 1" 012 50050 0 12 12 50250 4 15
5/16"-18 1-3/4" 2-11/16" 1-1/8" 1-1/4" 013 50053 1 13 13 50253 5 17.5
5/16"-18 1-3/4" 4-1/2" 2" 1-1/4" 013L 50056 2 19 13L 50256 6 24
5/16"-18 2" 2-11/16" 1" 1-1/2" 014 50059 3 14 14 50259 7 19
5/16"-18 2" 4-3/4" 3" 1-1/2" 014L 50062 3 20 14L 50262 7 25
5/16"-18 2-1/2" 3-3/16" 1" 2" 015 50065 4 16 15 50265 8 21
5/16"-18 2-1/2" 5-5/8" 3" 2" 015L 50068 5 23 15L 50268 9 29
5/16"-18 3" 3-11/16" 1" 2-1/2" 016 50071 5 18 16 50271 9 24
3/8"-16 1" 2-1/4" 1-1/4" 1/2" 017 50074 6 17.5 17 50274 0 22.5
3/8"-16 1-1/4" 2-1/4" 1-1/4" 3/4" 018 50077 7 18 18 50277 1 24
3/8"-16 1-1/2" 2-1/2" 1-1/4" 1" 019 50080 7 18.5 19 50280 1 26
3/8"-16 1-3/4" 2-3/4" 1-1/8" 1-1/4" 020 50083 8 20 20 50283 2 27.5
3/8"-16 2" 2-5/8" 1-1/4" 1-1/2" 021 50086 9 20 21 50286 3 29
3/8"-16 2-1/2" 3-1/8" 1-1/4" 2" 022 50089 0 24.5 22 50289 4 33
3/8"-16 3" 3-5/8" 1-1/4" 2-1/2" 023 50092 0 26 23 50292 4 38
3/8"-16 3" 6-5/8" 3" 2-1/2" 023L 50095 1 41 23L 50295 5 52.5
3/8"-16 3-1/2" 4-1/8" 1-1/4" 3" 024 50098 2 30 24 50298 6 42.5
1/2"-13 3" 4-1/2" 1-5/8" 2-1/2" 025 50101 9 59 25 50301 3 71
1/2"-13 3-1/2" 5" 1-1/2" 3" 026 50104 0 64 26 50304 4 78
1/2"-13 3-1/2" 8-1/2" 3" 3" 026L 50107 1 95 26L 50307 5 110
1/2"-13 4" 5-1/2" 1-1/2" 3-1/2" 027 50110 1 70 27 50310 5 87
1/2"-13 4-1/2" 6" 1-1/2" 4" 028 50113 2 75 28 50313 6 92.5
1/2"-13 5-5/8" 7-1/4" 2" 5" 029 50116 3 90 N.A. N.A. N.A.
1/2"-13 6-3/4" 8-3/8" 2" 6" 030 50119 4 101 N.A. N.A. N.A.
1/2"-13 8-3/4" 10-3/8" 2" 8" 031 50122 4 120 N.A. N.A. N.A.
*3/4"-10 10-7/8" 13-13/16" 4" 10" 032 50125 5 440 N.A. N.A. N.A.
*7/8"-9 12-7/8" 16-1/16" 4-1/4" 12" 033 50128 6 710 N.A. N.A. N.A.
*7/8"-9 14-1/8" 17-5/16" 4-1/4" 14" 034 50131 6 755 N.A. N.A. N.A.
*7/8"-9 16-1/8" 19-5/16" 4-1/4" 16" 035 50134 7 850 N.A. N.A. N.A.
*1"-8 18-1/8" 21-11/16" 4-3/4" 18" 036 50137 8 1245 N.A. N.A. N.A.

*Full Stock Diameter with Cut Thread.

See page 34 for dimensions of steel pipe.
32 Chicago Hardware and Fixture Company Since 1912
 ROUND BEND U-BOLTS
Zinc plated and hot galvanized finishes are standard. Other types of
rust preventative coatings or self-colored (black) available on a special
basis. Round, Square or “V” type U-Bolts to 1" diameter manufactured
to specifications in both ferrous and non-ferrous metals.
Stock numbers followed by “L” denote long length u-bolts designed Made in U S A
for use in applications requiring longer tangents.
See additional specifications and dimensions on the next page.

HOT GALVANIZED Some sizes also available in Stainless Steel. See page 50.
U-Bolt Dimensions – Inches For U-Bolts & 2 Nuts U-Bolts, Plates & 2 Nuts
Diameter I.D. Inside Thread Pipe Stock Part Weight Stock Part Weight
& Thread (A) (C) Length (B) Length (T) Size No. No. Per 100 No. No. Per 100
1/4"-20 9/16" 1-1/4" 3/4" 1/4" 01HG 53005 7 5 1HG 53605 9 7
1/4"-20 3/4" 1-1/4" 5/8" 3/8" 02HG 53008 8 5 2HG 53608 0 7
1/4"-20 3/4" 2-1/4" 1-1/2" 3/8" 03HG 53011 8 7 3HG 53611 0 9
1/4"-20 1" 1-3/4" 1" 1/2" 04HG 53014 9 7 4HG 53614 1 9
1/4"-20 1" 2-3/4" 1-1/4" 1/2" 04LHG 53017 0 8 4LHG 53617 2 11
1/4"-20 1-1/8" 2" 1" 3/4" 05HG 53020 0 7 5HG 53620 2 9
1/4"-20 1-1/8" 3-1/8" 1-1/2" 3/4" 05LHG 53023 1 9 5LHG 53623 3 12
1/4"-20 1-1/4" 2-1/4" 1-1/4" 3/4" 06HG 53026 2 7.5 6HG 53626 4 10
1/4"-20 1-1/2" 2-3/4" 1-3/8" 1" 07HG 53029 3 9 7HG 53629 5 12
1/4"-20 1-3/4" 3" 1-3/8" 1-1/4" 08HG 53032 3 9 8HG 53632 5 12
1/4"-20 2" 3-1/4" 1-3/8" 1-1/2" 09HG 53035 4 9.5 9HG 53635 6 14
5/16"-18 1" 2-3/16" 1-3/8" 1/2" 010HG 53038 5 11 10HG 53638 7 14
5/16"-18 1-1/8" 2-3/16" 1" 3/4" 0101HG 53041 5 12 101HG 53641 7 14.5
5/16"-18 1-3/8" 2-3/16" 1" 1" 011HG 53044 6 12 11HG 53644 8 15
5/16"-18 1-3/8" 3-5/8" 2" 1" 011LHG 53047 7 16 11LHG 53647 9 20
5/16"-18 1-1/2" 2-3/16" 1" 1" 012HG 53050 7 12 12HG 53650 9 15
5/16"-18 1-3/4" 2-11/16" 1-1/8" 1-1/4" 013HG 53053 8 13 13HG 53653 0 17.5
5/16"-18 1-3/4" 4-1/2" 2" 1-1/4" 013LHG 53056 9 19 13LHG 53656 1 24
5/16"-18 2" 2-11/16" 1" 1-1/2" 014HG 53059 0 14 14HG 53659 2 19
5/16"-18 2" 4-3/4" 3" 1-1/2" 014LHG 53062 0 20 14LHG 53662 2 25
5/16"-18 2-1/2" 3-3/16" 1" 2" 015HG 53065 1 16 15HG 53665 3 21
5/16"-18 2-1/2" 5-5/8" 3" 2" 015LHG 53068 2 23 15LHG 53668 4 29
5/16"-18 3" 3-11/16" 1" 2-1/2" 016HG 53071 2 18 16HG 53671 4 24
3/8"-16 1" 2-1/4" 1-1/4" 1/2" 017HG 53074 3 17.5 17HG 53674 5 22.5
3/8"-16 1-1/4" 2-1/4" 1-1/4" 3/4" 018HG 53077 4 18 18HG 53677 6 24
3/8"-16 1-1/2" 2-1/2" 1-1/4" 1" 019HG 53080 4 18.5 19HG 53680 6 26
3/8"-16 1-3/4" 2-3/4" 1-1/8" 1-1/4" 020HG 53083 5 20 20HG 53683 7 27.5
3/8"-16 2" 2-5/8" 1-1/4" 1-1/2" 021HG 53086 6 20 21HG 53686 8 29
3/8"-16 2-1/2" 3-1/8" 1-1/4" 2" 022HG 53089 7 24.5 22HG 53689 9 33
3/8"-16 3" 3-5/8" 1-1/4" 2-1/2" 023HG 53092 7 26 23HG 53692 9 38
3/8"-16 3" 6-5/8" 3" 2-1/2" 023LHG 53095 8 41 23LHG 53695 0 52.5
3/8"-16 3-1/2" 4-1/8" 1-1/4" 3" 024HG 53098 9 30 24HG 53698 1 42.5
1/2"-13 3" 4-1/2" 1-5/8" 2-1/2" 025HG 53101 6 59 25HG 53701 8 71
1/2"-13 3-1/2" 5" 1-1/2" 3" 026HG 53104 7 64 26HG 53704 9 78
1/2"-13 3-1/2" 8-1/2" 3" 3" 026LHG 53107 8 95 26LHG 53707 0 110
1/2"-13 4" 5-1/2" 1-1/2" 3-1/2" 027HG 53110 8 70 27HG 53710 0 87
1/2"-13 4-1/2" 6" 1-1/2" 4" 028HG 53113 9 75 28HG 53713 1 92.5
1/2"-13 5-5/8" 7-1/4" 2" 5" 029HG 53116 0 90 N.A. N.A. N.A.
1/2"-13 6-3/4" 8-3/8" 2" 6" 030HG 53119 1 101 N.A. N.A. N.A.
1/2"-13 8-3/4" 10-3/8" 2" 8" 031HG 53122 1 120 N.A. N.A. N.A.
*3/4"-10 10-7/8" 13-13/16" 4" 10" 032HG 53125 2 440 N.A. N.A. N.A.
*7/8"-9 12-7/8" 16-1/16" 4-1/4" 12" 033HG 53128 3 710 N.A. N.A. N.A.
*7/8"-9 14-1/8" 17-5/16" 4-1/4" 14" 034HG 53131 3 755 N.A. N.A. N.A.
*7/8"-9 16-1/8" 19-5/16" 4-1/4" 16" 035HG 53134 4 850 N.A. N.A. N.A.
*1"-8 18-1/8" 21-11/16" 4-3/4" 18" 036HG 53137 5 1245 N.A. N.A. N.A.

*Full Stock Diameter with Cut Thread

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 33
 ROUND BEND U-BOLTS
Made in U S A

ALUMINUM
U-Bolt Dimensions – Inches For U-Bolts & 2 Nuts
Diameter I.D. Inside Thread Pipe Stock Part Weight
& Thread (A) (C) Length (B) Length (T) Size No. No. Per 100
1/4"-20 3/4" 1-1/4" 5/8" 3/8" 02AL 60008 8 1.5
1/4"-20 1" 1-3/4" 1" 1/2" 04AL 60014 9 2
1/4"-20 1-1/8" 2" 1" 3/4" 05AL 60020 0 2
1/4"-20 1-1/2" 2-3/4" 1-3/8" 1" 07AL 60029 3 3.5
1/4"-20 1-3/4" 3" 1-3/8" 1-1/4" 08AL 60032 3 4
1/4"-20 2" 3-1/4" 1-3/8" 1-1/2" 09AL 60035 4 4
5/16"-18 1-3/8" 2-3/16" 1" 1" 011AL 60044 6 5
5/16"-18 2" 2-11/16" 1" 1-1/2" 014AL 60059 0 5.2
5/16"-18 2-1/2" 3-3/16" 1" 2" 015AL 60065 1 5.5
3/8"-16 1-1/2" 2-1/2" 1-1/4" 1" 019AL 60080 4 6.5
3/8"-16 2" 2-5/8" 1-1/4" 1-1/2" 021AL 60086 6 7
3/8"-16 2-1/2" 3-1/8" 1-1/4" 2" 022AL 60089 7 7.1
3/8"-16 3-1/2" 4-1/8" 1-1/4" 3" 024AL 60098 9 10.5
1/2"-13 3-1/2" 5" 1-1/2" 3" 026AL 60104 7 22.5
1/2"-13 4-1/2" 6" 1-1/2" 4" 028AL 60113 9 27
1/2"-13 6-3/4" 8-3/8" 2" 6" 030AL 60119 1 36

*Full Stock Diameter with Cut Thread

DIMENSIONS OF WELDED Some sizes also

AND SEAMLESS STEEL PIPE available in
Stainless Steel.
Pipe Outside See page 50.
Size Diameter
1/4" .540"
3/8" .675"
1/2" .840"
3/4" 1.05"
1" 1.315"
1-1/4" 1.66"
1-1/2" 1.90" U-BOLT PLATES
2" 2.375"
2-1/2" 2.875" U-Bolt plates are low carbon cold rolled steel with rounded
3" 3.500" edges and zinc plated or hot galvanized finish. Plate holes are
3-1/2" 4.000" punched “on centers” of corresponding size U-Bolt and
4" 4.500" identified by stock numbers.
5" 5.563"
6" 6.625"
Dimensions – Inches
8" 8.625"
For U-Bolt Diameter Gauge Width
10" 10.750"
1/4" and 5/16" .078" .750"
12" 12.750"
3/8" and 1/2" .109" 1.000"
14" 14.000"
16" 16.000"
18" 18.000"

34 Chicago Hardware and Fixture Company Since 1912

ROUND BEND LONG TANGENT U-BOLTS

ZINC PLATED U-BOLTS WITH 4 NUTS

A C B T Weight Per 100
Stock Part Pipe Inside Inside Thread U-Bolt U-Bolt &
Diameter
No. No. Size Width Length Length Only 4 Nuts
LT-B 51460 6 1/2" 1/4"-20 7/8" 2-15/16" 2-1/2" 6 9
LT-C 51465 1 3/4" 1/4"-20 1-1/8" 3-3/16" 2-1/2" 7 10
LT-D 51470 5 1" 1/4"-20 1-3/8" 3-7/16" 2-1/2" 8 11
LT-1 51505 4 1/2" 3/8"-16 15/16" 3" 2-3/8" 17.5 24
LT-2 51510 8 3/4" 3/8"-16 1-1/8" 3-5/16" 2-3/8" 19 25.5
LT-3 51515 3 1" 3/8"-16 1-3/8" 3-7/16" 2-3/8" 20 26.5
LT-4 51520 7 1-1/4" 3/8"-16 1-11/16" 3-23/32" 2-3/8" 21.5 28
LT-5 51525 2 1-1/2" 3/8"-16 2" 4" 2-1/2" 23.5 30
LT-6 51530 6 2" 3/8"-16 2-7/16" 4-7/16" 2-1/2" 26.5 33
LT-7 51535 1 2-1/2" 1/2"-13 2-15/16" 5-7/32" 3" 57 71
LT-8 51540 5 3" 1/2"-13 3-9/16" 5-3/4" 3" 62 77
LT-9 51545 0 3-1/2" 1/2"-13 4-1/16" 6-1/4" 3" 68 82
Zinc Plated
LT-10 51550 4 4" 1/2"-13 4-9/16" 6-3/4" 3" 74 89
LT-11 51555 9 5" 1/2"-13 5-5/8" 7-13/16" 3" 86 101
LT-12 51560 3 6" 5/8"-11 6-3/4" 9-1/2" 3-3/4" 167 194.5
LT-13 51565 8 8" 5/8"-11 8-3/4" 11-1/8" 3-3/4" 196 223.5
LT-14 51570 2 10" 3/4"-10 10-7/8" 13-13/16" 4" 440 460

HOT GALVANIZED U-BOLTS WITH 4 NUTS

A C B T Weight Per 100
Stock Part Pipe Inside Inside Thread U-Bolt U-Bolt &
Diameter
No. No. Size Width Length Length Only 4 Nuts
LT-BHG 53165 8 1/2" 1/4"-20 7/8" 2-15/16" 2-1/2" 7 9
LT-CHG 53175 7 3/4" 1/4"-20 1-1/8" 3-3/16" 2-1/2" 8 10
LT-DHG 53180 1 1" 1/4"-20 1-3/8" 3-7/16" 2-1/2" 9 11
LT-1 HG 53205 1 1/2" 3/8"-16 15/16" 3" 2-3/8" 17.5 24
LT-2 HG 53210 5 3/4" 3/8"-16 1-1/8" 3-5/16" 2-3/8" 19 25.5
LT-3 HG 53215 0 1" 3/8"-16 1-3/8" 3-7/16" 2-3/8" 20 26.5
LT-4 HG 53220 4 1-1/4" 3/8"-16 1-11/16" 3-23/32" 2-3/8" 21.5 28
LT-5 HG 53225 9 1-1/2" 3/8"-16 2" 4" 2-1/2" 23.5 30
LT-6 HG 53230 3 2" 3/8"-16 2-7/16" 4-7/16" 2-1/2" 26.5 33
LT-7 HG 53235 8 2-1/2" 1/2"-13 2-15/16" 5-7/32" 3" 57 71
LT-8 HG 53240 2 3" 1/2"-13 3-9/16" 5-3/4" 3" 62 77
LT-9 HG 53245 7 3-1/2" 1/2"-13 4-1/16" 6-1/4" 3" 68 82
LT-10 HG 53250 1 4" 1/2"-13 4-9/16" 6-3/4" 3" 74 89
Hot Galvanized
LT-11 HG 53255 6 5" 1/2"-13 5-5/8" 7-13/16" 3" 86 101
LT-12 HG 53260 0 6" 5/8"-11 6-3/4" 9-1/2" 3-3/4" 167 194.5
LT-13 HG 53265 5 8" 5/8"-11 8-3/4" 11-1/8" 3-3/4" 196 223.5
LT-14 HG 53270 9 10" 3/4"-10 10-7/8" 13-13/16" 4" 440 460

Made in U S A
Some sizes also available in Stainless Steel. See page 51.

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 35

 SQUARE BEND U-BOLTS
Furnished with 3/8" nuts and flat washers.

ZINC PLATED U-BOLTS WITH 2 NUTS AND 2 WASHERS

A C B T Weight Per 100
Stock Part Inside Overall Thread U-Bolt U-Bolt &
Diameter
No. No. Width Length Length Only 4 Nuts
SB-1 51005 9 3/8"-16 2" 3" 1-1/2" 19 25.5
SB-2 51010 3 3/8"-16 2" 5" 3" 29 35.5
SB-3 51015 8 3/8"-16 2" 7" 3-3/4" 38.5 44.5
SB-4 51020 2 3/8"-16 4" 3" 1-1/2" 23.5 29.5
SB-5 51025 7 3/8"-16 4" 5" 3" 33.5 40
SB-6 51030 1 3/8"-16 4" 7" 3-3/4" 43.5 49.5
SB-7 51035 6 3/8"-16 6" 5" 3" 38.5 44.5
SB-8 51040 0 3/8"-16 6" 7" 3-3/4" 48 56
Zinc Plated SB-9 51045 5 3/8"-16 6" 9" 5-5/8" 57 63

Also available in Stainless Steel. See page 51.

Made in U S A

HOT GALVANIZED U-BOLTS WITH 2 NUTS AND 2 WASHERS

A C B T Weight Per 100
Stock Part Inside Overall Thread U-Bolt U-Bolt &
Diameter
No. No. Width Length Length Only 4 Nuts
SB-1HG 53405 5 3/8"-16 2" 3" 1-1/2" 19 25.5
SB-2HG 53410 9 3/8"-16 2" 5" 3" 29 35.5
SB-3HG 53415 4 3/8"-16 2" 7" 3-3/4" 38.5 44.5
SB-4HG 53420 8 3/8"-16 4" 3" 1-1/2" 23.5 29.5
SB-5HG 53425 3 3/8"-16 4" 5" 3" 33.5 40
SB-6HG 53430 7 3/8"-16 4" 7" 3-3/4" 43.5 49.5
SB-7HG 53435 2 3/8"-16 6" 5" 3" 38.5 44.5
SB-8HG 53440 6 3/8"-16 6" 7" 3-3/4" 48 56
SB-9HG 53445 1 3/8"-16 6" 9" 5-5/8" 57 63
Hot Galvanized

U-BOLT DISPLAY U-BOLT DISPLAY PART # 60040 8

Thread
Qty. Stock No. Pipe Size
Diameter
10 4 1/2" 1/4"-20
10 5 3/4" 1/4"-20
10 5L 3/4" 1/4"-20
10 7 1" 1/4"-20
10 11 1" 5/16"-18
10 11L 1" 5/16"-18
10 13 1-1/4" 5/16"-18
10 13L 1-1/4" 5/16"-18
10 14 1-1/2" 5/16"-18
10 14L 1-1/2" 5/16"-18
10 15 2" 5/16"-18
10 15L 2" 5/16"-18
10 22 2" 3/8"-16
10 24 3" 3/8"-16

140 U-Bolts
Shipping Wt. .................35 lbs.

36 Chicago Hardware and Fixture Company Since 1912

 ZINC PLATED TURNED EYE BOLTS
Turned eye bolts are manufactured from low carbon cold drawn steel wire and are supplied
with NC rolled machine threads with one hex nut unassembled. Zinc plated finish is
standard; other rust preventive finishes or self-colored available on a special basis. When
it is not feasible to utilize a standard eye bolt, we can manufacture to your specifications.

MACHINE Dimensions – Inches Weight Working

Thread Shank I.D. Eye Overall Thread Per 100 Load
THREAD Stock No. Part No. in lbs. Limit (lbs.)
Diameter (A) Length (B) (C) Length (D) Length (T)
A-1 07005 8 1/8" (6-32) 3/4" 1/4" 1-1/4" 5/8" .75 22
B-1 07010 2 5/32" (8-32) 1-1/8" 1/4" 1-11/16" 1" 1.31 36
C-1 07015 7 3/16" (10-24) 1" 3/8" 1-11/16" 7/8" 1.81 38
C-2 07020 1 3/16" (10-24) 1-3/8" 5/16" 2" 1-1/4" 1.875 38
C-3 07025 6 3/16" (10-24) 2" 3/8" 2-11/16" 1" 2.375 38
C-4 07030 0 3/16" (10-24) 3" 3/8" 3-11/16" 1-1/2" 2.94 38
D-1 07035 5 7/32" (12-24) 1-1/2" 3/8" 2-1/4" 1-3/8" 1.67 52
E-1 07040 9 1/4"-20 1" 1/2" 2" 7/8" 3.75 74
E-2 07045 4 1/4"-20 1-1/2" 1/2" 2-1/2" 1-1/4" 4.375 74
E-2A 07050 8 1/4"-20 1-7/8" 7/16" 2-3/4" 1-5/8" 5.2 74
E-3 07055 3 1/4"-20 2" 1/2" 3" 1-1/4" 5 74
E-4 07060 7 1/4"-20 2-1/2" 1/2" 3-1/2" 1-1/4" 5.6 74
E-5 07065 2 1/4"-20 3" 1/2" 4" 1-1/2" 6.3 74
E-6 07070 6 1/4"-20 3-1/2" 1/2" 4-1/2" 2" 6.9 74
E-7 07075 1 1/4"-20 4" 1/2" 5" 2-1/2" 7.5 74
E-8 07080 5 1/4"-20 5" 1/2" 6" 3" 8 74
E-9 07085 0 1/4"-20 6" 1/2" 7" 4" 9 74
F-1 07090 4 5/16"-18 1" 5/8" 2-1/8" 7/8" 7 96
F-2 07095 9 5/16"-18 2" 5/8" 3-1/8" 1-1/4" 9 96
F-2A 07100 0 5/16"-18 2-1/4" 9/16" 3-3/8" 2" 9.7 96
F-3 07105 5 5/16"-18 2-1/2" 5/8" 3-5/8" 1-1/4" 10 96
F-4 07110 9 5/16"-18 3" 5/8" 4-1/8" 1-1/2" 11 96
F-5 07115 4 5/16"-18 3-1/2" 5/8" 4-5/8" 2" 11 96
F-6 07120 8 5/16"-18 4" 5/8" 5-1/8" 2-1/2" 12 96
F-7 07125 3 5/16"-18 5" 5/8" 6-1/8" 3" 14 96
F-8 07130 7 5/16"-18 6" 5/8" 7-1/8" 4" 15 96
F-9 07135 2 5/16"-18 6-1/2" 7/8" 7-3/4" 4" 18 96
G-1 07140 6 3/8"-16 1" 3/4" 2-1/2" 7/8" 12 144
G-2 07145 1 3/8"-16 2" 3/4" 3-1/2" 1-1/4" 15 144
G-2A 07150 5 3/8"-16 2-1/2" 21/32" 3-3/4" 2-1/4" 15.7 144
G-3 07155 0 3/8"-16 2-1/2" 3/4" 4" 1-1/2" 15.5 144
G-4 07160 4 3/8"-16 3" 3/4" 4-1/2" 1-1/2" 17 144
G-5 07165 9 3/8"-16 3-1/2" 3/4" 5" 2" 18 144
G-6 07170 3 3/8"-16 4" 3/4" 5-1/2" 2-1/2" 21 144
G-7 07175 8 3/8"-16 5" 3/4" 6-1/2" 3" 22 144
Made in U S A G-8 07180 2 3/8"-16 6" 3/4" 7-1/2" 4" 24 144
G-9 07185 7 3/8"-16 8" 3/4" 9-1/2" 4" 30 144
G-10 07190 1 3/8"-16 10" 3/4" 11-1/2" 4" 34 144
G-11 07195 6 3/8"-16 12" 3/4" 13-1/2" 4" 39 144
H-1 07200 7 7/16"-14 6" 7/8" 7-3/4" 4" 36 216
H-2 07205 2 7/16"-14 8" 7/8" 9-3/4" 4" 42 216
J-1 07210 6 1/2"-13 2" 1" 4" 1-1/2" 33 298
Some sizes also
J-2 07215 1 1/2"-13 4" 1" 6" 2-1/2" 41 298
available in
J-3 07220 5 1/2"-13 6" 1" 8" 4" 50 298
Stainless Steel.
J-4 07225 0 1/2"-13 8" 1" 10" 4" 58 298
See page 49.
J-5 07230 4 1/2"-13 10" 1" 12" 4" 68 298
Standard Pack
A-1 through D-1: 50 Pieces
E-1 through J-5: 10 Pieces
Chicago • Chino • Atlanta • Houston www.chicagohardware.com 37
 ZINC PLATED TURNED EYE BOLTS

LAG THREADS
Lag Screw threaded Turned Eye Bolts are comparable in steel specification, finish
and packaging to machine thread Turned Eye Bolts listed on page 37. Lag screw
threads are rolled to fit standard anchors and shields and supplied with gimlet point.
Dimensions – Inches Weight
Thread Shank I.D. Eye Overall Thread Per 100
Stock No. Part No. in lbs.
Diameter (A) Length (B) (C) Length (D) Length (T)
LS-1 07855 9 1/4" 2-3/4" 1/2" 3-11/16" 2" 5
LS-2 07860 3 1/4" 4" 1/2" 4-7/8" 2" 6
LS-3 07865 8 5/16" 2-3/4" 5/8" 3-7/8" 2" 8
LS-4 07870 2 5/16" 4-3/4" 5/8" 5-13/16" 2" 11
LS-5 07875 7 3/8" 3" 3/4" 4-3/8" 2-1/2" 13
LS-6 07880 1 3/8" 6" 3/4" 7-5/16" 2-1/2" 19
LS-7 07885 6 1/2" 3-1/2" 1" 5-1/4" 2-3/4" 30

Standard Pack – 10 Pieces

TURNED EYE BOLT
DISPLAY
PART # 60030 9 TURNED EYE BOLT DISPLAY
Diameter &
Qty. Stock No.
Shank Length
10 C-1 3/16" x 1"
Made in U S A
10 C-2 3/16" x 1-3/8"
10 C-3 3/16" x 2"
10 E-1 1/4" x 1"
10 E-2 1/4" x 1-1/2"
10 E-3 1/4" x 2"
10 E-5 1/4" x 3"
10 E-7 1/4" x 4"
10 F-2 5/16" x 2"
10 F-4 5/16" x 3"
10 F-6 5/16" x 4"
10 F-7 5/16" x 5"
10 G-3 3/8" x 2-1/2"
10 G-5 3/8" x 3-1/2"
10 G-6 3/8" x 4"
10 G-8 3/8" x 6"
10 J-2 1/2" x 4"
10 J-3 1/2" x 6"
10 J-4 1/2" x 8"

190 Eyebolts WELDED – MACHINE THREADS

Shipping Wt. …………. 37 lbs. Comparable in specifications, finish and standard packaging
with exception Eyes are resistance welded closed.

Dimensions – Inches Weight Working

Thread Shank I.D. Eye Overall Thread Per 100 Load
Stock No. Part No. in lbs. Limit (lbs.)
Diameter (A) Length (B) (C) Length (D) Length (T)
F-3W 07755 2 5/16"-18 2-1/2" 5/8" 3-5/8" 1-1/4" 10 240
G-3W 07760 6 3/8"-16 2-1/2" 3/4" 4" 1-1/2" 16 400
G-6W 07765 1 3/8"-16 4" 3/4" 5-1/2" 2-1/2" 20 400
J-2W 07770 5 1/2"-13 4" 1" 6" 2-1/2" 41 1000
J-3W 07775 0 1/2"-13 6" 1" 8" 4" 50 1000

Standard Pack – 10 Pieces

38 Chicago Hardware and Fixture Company Since 1912
 CONTINUOUS THREADED ROD
Manufactured from Low Carbon Domestic Steel – 12", 24" and 36" lengths, color coded,
bundled and packed in standard cartons, as noted, for convenience. 72", 120" and 144"
lengths not coded or bundled, but packed in standard identified cartons. Lengths, other
than standard and fully threaded or double end carbon steel studs, manufactured to
specification. NC and NF rolled threads.
Made in U S A
STEEL-OIL FINISH
12” – 24” – 36” LENGTHS
12" RODS 24" RODS 36" RODS
Bundle Bundle Carton Bundle Carton
Thread Color Part Weight Part Weight Weight Part Weight Weight
Quantity Quantity Quantity Quantity Quantity
Diameter Code No. (lbs) No. (lbs) (lbs) No. (lbs) (lbs)
6 - 32 Blue 39005 7 5 0.2 39008 8 5 0.4 * * 39011 8 5 0.6 * *
8 - 32 Red 39025 5 5 0.3 39028 6 5 0.5 * * 39031 6 5 0.8 * *
10 - 24 Green 39045 3 5 0.3 39048 4 5 0.6 * * 39051 4 5 0.9 * *
12 - 24 Red 39065 1 5 0.4 39068 2 5 0.9 * * 39071 2 5 1.3 * *
1/4" - 20 Blue 39085 9 5 0.6 39088 0 5 1.3 200 48 39091 0 5 1.9 200 72
5/16" - 18 Red 39105 4 5 1 39108 5 5 2 125 50 39111 5 5 3 125 75
3/8" - 16 Yellow 39125 2 5 1.4 39128 3 5 2.9 100 57 39131 3 5 4.3 100 86
7/16" - 14 Green 39145 0 5 2 39148 1 5 4 70 56 39151 1 5 6 70 84
1/2" - 13 Blue 39165 8 5 2.6 39168 9 5 5.3 50 53 39171 9 5 7.9 50 79
9/16" - 12 Yellow 39185 6 3 2 39188 7 3 4 33 44 39191 7 3 6 33 66
5/8" - 11 Red 39205 1 3 2.5 39208 2 3 5 33 55 39211 2 3 7.5 33 83
3/4" - 10 Yellow 39225 9 3 3.7 39228 0 3 7.4 24 59 39231 0 3 11.1 24 88
7/8" - 9 Green 39245 7 3 5.1 39248 8 3 10.1 15 51 39251 8 3 15.2 15 76
1" - 8 Red 39265 5 3 6.7 39268 6 3 13.4 12 54 39271 6 3 20.1 12 81
1-1/8" - 7 Yellow 39285 3 N.A. N.A. 39288 4 N.A. N.A. 10 56 39291 4 N.A. N.A. 10 84
1-1/4" - 7 Green 39305 8 N.A. N.A. 39308 9 N.A. N.A. 10 70 39311 9 N.A. N.A. 10 105
1-3/8" - 6 Blue 39325 6 N.A. N.A. 39328 7 N.A. N.A. 10 84 39331 7 N.A. N.A. 10 126
1-1/2" - 6 Red 39345 4 N.A. N.A. 39348 5 N.A. N.A. 5 51 39351 5 N.A. N.A. 5 76

*No established quantity.

72” – 120” – 144” LENGTHS
72" RODS 120" RODS 144" RODS Estimated
Weight
Carton Carton Carton Per
Thread Color Part Weight Part Weight Part Weight 100 Ft.
Quantity Quantity Quantity (lbs)
Diameter Code No. (lbs) No. (lbs) No. (lbs)
6 - 32 Blue 39014 9 * * 39017 0 * * 39020 0 * * 3.6
8 - 32 Red 39034 7 * * 39037 8 * * 39040 8 * * 5.3
10 - 24 Green 39054 5 * * 39057 6 * * 39060 6 * * 6.7
12 - 24 Red 39074 3 * * 39077 4 * * 39080 4 * * 9.2
1/4" - 20 Blue 39094 1 150 109 39097 2 90 109 39100 9 75 109 12.1
5/16" - 18 Red 39114 6 100 117 39117 7 60 117 39120 7 50 117 19.6
3/8" - 16 Yellow 39134 4 70 120 39137 5 42 120 39140 5 35 120 28.7
7/16" - 14 Green 39154 2 50 119 39157 3 30 119 39160 3 25 119 39.8
1/2" - 13 Blue 39174 0 36 114 39177 1 22 116 39180 1 18 114 52.6
9/16" - 12 Yellow 39194 8 24 96 39197 9 14 93 39200 6 12 96 66.7
5/8" - 11 Red 39214 3 24 120 39217 4 14 117 39220 4 12 120 83.3
3/4" - 10 Yellow 39234 1 16 118 39237 2 9 110 39240 2 8 118 123
7/8" - 9 Green 39254 9 12 122 39257 0 7 118 39260 0 6 122 170
1" - 8 Red 39274 7 9 120 39277 8 5 112 39280 8 4 107 223
1-1/8" - 7 Yellow 39294 5 6 101 39297 6 4 112 39300 3 3 101 280
1-1/4" - 7 Green 39314 0 5 106 39317 1 3 106 39320 1 2 84 352
1-3/8" - 6 Blue 39334 8 5 126 39337 9 3 126 39340 9 2 101 421
1-1/2" - 6 Red 39354 6 4 123 39357 7 2 102 39360 7 2 123 510

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 39

 CONTINUOUS THREADED ROD
Manufactured from Low Carbon Domestic Steel – 12", 24" and 36" lengths, color coded,
bundled and packed in standard cartons, as noted, for convenience. 72", 120" and 144"
lengths not coded or bundled, but packed in standard identified cartons. Lengths, other
than standard and fully threaded or double end carbon steel studs, manufactured to
specification. NC and NF rolled threads.
Made in U S A
ZINC PLATED STEEL
12” – 24” – 36” LENGTHS
12" RODS 24" RODS 36" RODS
Bundle Bundle Carton Bundle Carton
Thread Color Part Weight Part Weight Weight Part Weight Weight
Quantity Quantity Quantity Quantity Quantity
Diameter Code No. (lbs) No. (lbs) (lbs) No. (lbs) (lbs)
6 - 32 Blue 35005 1 5 0.2 35008 2 5 0.4 * * 35011 2 5 0.6 * *
8 - 32 Red 35025 9 5 0.3 35028 0 5 0.5 * * 35031 0 5 0.8 * *
10 - 24 Green 35045 7 5 0.3 35048 8 5 0.6 * * 35051 8 5 0.9 * *
12 - 24 Red 35065 5 5 0.4 35068 6 5 0.9 * * 35071 6 5 1.3 * *
1/4" - 20 Blue 35085 3 5 0.6 35088 4 5 1.3 200 48 35091 4 5 1.9 200 72
5/16" - 18 Red 35105 8 5 1 35108 9 5 2 125 50 35111 9 5 3 125 75
3/8" - 16 Yellow 35125 6 5 1.4 35128 7 5 2.9 100 57 35131 7 5 4.3 100 86
7/16" - 14 Green 35145 4 5 2 35148 5 5 4 70 56 35151 5 5 6 70 84
1/2" - 13 Blue 35165 2 5 2.6 35168 3 5 5.3 50 53 35171 3 5 7.9 50 79
9/16" - 12 Yellow 35185 0 3 2 35188 1 3 4 33 44 35191 1 3 6 33 66
5/8" - 11 Red 35205 5 3 2.5 35208 6 3 5 33 55 35211 6 3 7.5 33 83
3/4" - 10 Yellow 35225 3 3 3.7 35228 4 3 7.4 24 59 35231 4 3 11.1 24 88
7/8" - 9 Green 35245 1 3 5.1 35248 2 3 10.1 15 51 35251 2 3 15.2 15 76
1" - 8 Red 35265 9 3 6.7 35268 0 3 13.4 12 54 35271 0 3 20.1 12 81
1-1/8" - 7 Yellow 35285 7 N.A. N.A. 35288 8 N.A. N.A. 10 56 35291 8 N.A. N.A. 10 84
1-1/4" - 7 Green 35305 2 N.A. N.A. 35308 3 N.A. N.A. 10 70 35311 3 N.A. N.A. 10 105
1-3/8" - 6 Blue 35325 0 N.A. N.A. 35328 1 N.A. N.A. 10 84 35331 1 N.A. N.A. 10 126
1-1/2" - 6 Red 35345 8 N.A. N.A. 35348 9 N.A. N.A. 5 51 35351 9 N.A. N.A. 5 76

*No established quantity.

72” – 120” – 144” LENGTHS
Estimated
72" RODS 120" RODS 144" RODS
Weight
Carton Carton Carton Per
Thread Color Part Weight Part Weight Part Weight 100 Ft.
Quantity Quantity Quantity (lbs)
Diameter Code No. (lbs) No. (lbs) No. (lbs)
6 - 32 Blue 35014 3 * * 35017 4 * * 35020 4 * * 3.6
8 - 32 Red 35034 1 * * 35037 2 * * 35040 2 * * 5.3
10 - 24 Green 35054 9 * * 35057 0 * * 35060 0 * * 6.7
12 - 24 Red 35074 7 * * 35077 8 * * 35080 8 * * 9.2
1/4" - 20 Blue 35094 5 150 109 35097 6 90 109 35100 3 75 109 12.1
5/16" - 18 Red 35114 0 100 117 35117 1 60 117 35120 1 50 117 19.6
3/8" - 16 Yellow 35134 8 70 120 35137 9 42 120 35140 9 35 120 28.7
7/16" - 14 Green 35154 6 50 119 35157 7 30 119 35160 7 25 119 39.8
1/2" - 13 Blue 35174 4 36 114 35177 5 22 116 35180 5 18 114 52.6
9/16" - 12 Yellow 35194 2 24 96 35197 3 14 93 35200 0 12 96 66.7
5/8" - 11 Red 35214 7 24 120 35217 8 14 117 35220 8 12 120 83.3
3/4" - 10 Yellow 35234 5 16 118 35237 6 9 110 35240 6 8 118 123
7/8" - 9 Green 35254 3 12 122 35257 4 7 118 35260 4 6 122 170
1" - 8 Red 35274 1 9 120 35277 2 5 112 35280 2 4 107 223
1-1/8" - 7 Yellow 35294 9 6 101 35297 0 4 112 35300 7 3 101 280
1-1/4" - 7 Green 35314 4 5 106 35317 5 3 106 35320 5 2 84 352
1-3/8" - 6 Blue 35334 2 5 126 35337 3 3 126 35340 3 2 101 421
1-1/2" - 6 Red 35354 0 4 123 35357 1 2 102 35360 1 2 123 510

40 Chicago Hardware and Fixture Company Since 1912

 CONTINUOUS THREADED ROD
BRASS
Brass Threaded Rod, both in National Coarse and National Fine Thread
Series, is also available in 120" and 144" lengths on a special basis.
Intermediate lengths and studs are also available on a special basis.
Made in U S A
36” AND 72” LENGTHS
36" Length 72" Length
Bundle Carton Carton
Thread Weight Weight Weight
Part No. Quantity Quantity Part No. Quantity
Diameter (lbs) (lbs) (lbs)
6 - 32 36011 1 10 1.2 * * 36014 2 * *
8 - 32 36031 9 10 1.7 * * 36034 0 * *
10 - 24 36051 7 10 2.2 * * 36054 8 * *
12 - 24 36071 5 10 2.9 * * 36074 6 * *
1/4" - 20 36091 3 5 2.0 200 79 36094 4 150 129
5/16" - 18 36111 8 5 3.0 125 75 36114 9 160 129
3/8" - 16 36131 6 5 4.5 100 90 36134 7 70 134
7/16" - 14 36151 4 5 6.3 70 88 36154 5 50 130
1/2" - 13 36171 2 5 8.4 50 84 36174 3 36 125
5/8" - 11 36211 5 3 8.1 33 89 36214 6 24 132
3/4" - 10 36231 3 3 12.0 24 94 36234 4 16 129

304 STAINLESS STEEL

36”, 72” AND 144” LENGTHS
36" Length 72" Length 144" Length Estimated
Weight
Bundle Carton Carton Carton Per
Thread Weight Weight Weight Weight 100 Ft.
Part No. Quantity Quantity Part No. Quantity Part No. Quantity (lbs)
Diameter (lbs) (lbs) (lbs) (lbs)
6 - 32 37011 0 5 .50 * * 37014 1 * * 37020 2 * * 3.6
8 - 32 37031 8 5 .75 * * 37034 9 * * 37040 0 * * 5.3
10 - 24 37051 6 5 1 * * 37054 7 * * 37060 8 * * 6.7
12 - 24 37071 4 5 1.35 * * 37074 5 * * 37080 6 * * 9.2
1/4" - 20 37091 2 5 1.8 200 72 37094 3 150 109 37100 1 75 107 12.1
5/16" - 18 37111 7 5 3.0 125 75 37114 8 100 117 37120 9 50 117 19.6
3/8" - 16 37131 5 5 4.3 100 86 37134 6 70 120 37140 7 35 120 28.7
7/16" - 14 37151 3 5 6 70 84 37154 4 50 119 37160 5 25 119 39.8
1/2" - 13 37171 1 5 8.1 50 81 37174 2 36 114 37180 3 18 114 52.6
9/16" - 12 37191 9 3 6 33 68 37194 0 24 96 37200 8 12 96 66.7
5/8" - 11 37211 4 5 7.7 33 85 37214 5 24 120 37220 6 12 120 83.3
3/4" - 10 37231 2 3 11.2 24 90 37234 3 16 118 37240 4 8 118 123
7/8" - 9 37251 0 3 16 15 76 37254 1 12 122 37260 2 6 122 170
1" - 8 37271 8 3 20.3 12 80 37274 9 9 120 37280 0 4 107 223

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 41

 CONTINUOUS THREADED ROD
Made in U S A HOT GALVANIZED CARBON STEEL
36” AND 72” LENGTHS

Thread Color 36" Length 72" Length Weight Per

ZINC PLATED Diameter Code Part No. Part No. 100 Ft. (lbs)
ONE FOOT THREADED 3/8" - 16
7/16" - 14
Yellow
Green
46131 3
46151 1
46134 4
46154 2
28.7
39.8
ROD DISPLAY: 1/2" - 13 Blue 46171 9 46174 0 52.6
5/8" - 11 Red 46211 2 46214 3 83.3
3/4" - 10 Yellow 46231 0 46234 1 123
7/8" - 9 Green 46251 8 46254 9 170
1" - 8 Red 46271 6 46274 7 223
1-1/4" - 7 Green 46311 9 46314 0 352

B7-ALLOY – SELF-COLORED
36”, 72” AND 144” LENGTHS
Thread Color 36" Length 72" Length 144" Length Weight Per
Diameter Code Part No. Part No. Part No. 100 Ft. (lbs)
1/4" - 20 Blue 38091 1 38094 2 38100 0 12.1
5/16" - 18 Red 38111 6 38114 7 38120 8 19.6
3/8" - 16 Yellow 38131 4 38134 5 38140 6 28.7
CHICAGO ONE FOOT ZINC PLATED 7/16" - 14 Green 38151 2 38154 3 38160 4 39.8
THREADED ROD DISPLAY 1/2" - 13 Blue 38171 0 38174 1 38180 2 52.6
Part No. 60160 3
5/8" - 11 Red 38211 3 38214 4 38220 5 83.3
Each Assortment Contains
3/4" - 10 Yellow 38231 1 38234 2 38240 3 123
The Following:
7/8" - 9 Green 38251 9 38254 0 38260 1 170
35 Each 1/4" - 20 x 1' 35 Each 3/8" - 16 x 1'
1" - 8 Red 38271 7 38274 8 38280 9 223
35 Each 5/16" - 18 x 1' 30 Each 1/2" - 13 x 1'
1-1/8" - 7 Yellow 38291 5 38294 6 38300 4 280
Shipping Weight: 38 Lbs.
1-1/8" - 8 Yellow 38311 0 38314 1 38320 2 292
Each size is color coded for easy identification
1-1/4" - 7 Green 38331 8 38334 9 38340 0 352
One Foot Threaded Rod Display 1-1/4" - 8 Green 38351 6 38354 7 38360 8 366
can be substituted for Key Stock. 1-1/2" - 6 Red 38391 2 38394 3 38400 1 510
1-1/2" - 8 Red 38411 7 38414 8 38420 9 534

ZINC PLATED STEEL COUPLING NUTS

Pieces Estimated Estimated National Coarse Right
Tap Part Outside Overall Hand Thread. For joining
Per Weight Per Weight
Size No. Hex Length threaded rods where
Package Package (lbs) Per 100 (lbs)
span of application
10 - 24 25505 9 5/16" 3/4" 50 .35 .7
exceeds 144" or where a
1/4" - 20 25510 3 3/8" 7/8" 50 1 2
threaded fitting is used
5/16" - 18 25515 8 1/2" 1-1/8" 25 .75 3
with threaded rod in
3/8" - 16 25520 2 5/8" 1-3/4" 25 2.9 11
suspension applications.
7/16" - 14 25525 7 11/16" 1-3/4" 25 2.6 10
1/2" - 13 25530 1 11/16" 1-3/4" 25 3 12
5/8" - 11 25535 6 13/16" 2-1/8" 20 3.7 18
3/4" - 10 25540 0 1" 2-1/4" 20 6 29
7/8" - 9 25545 5 1-1/4" 2-1/2" 10 5.3 53
1" - 8 25550 9 1-3/8" 2-3/4" 10 7 70
1-1/8" - 7 25555 4 1-1/2" 3" 10 9 90
1-1/4" - 7 25560 8 1-5/8" 3" 10 9.8 97

42 Chicago Hardware and Fixture Company Since 1912

 ZINC PLATED STEEL “SHAPES”
Special lengths available upon request.
SQUARE KEY
Estimated
12" Length 24" Length 36" Length
Weight
Bundle Bundle Bundle Per
Part Weight Part Weight Part Weight 100 Ft. Made in U S A
Size Quantity Quantity Quantity (lbs)
No. (lbs) No. (lbs) No. (lbs)
1/8" 31005 5 6 .32 31505 0 N.A. N.A. 31250 9 N.A. N.A. 5.3
5/32" 31010 9 6 .50 31510 4 N.A. N.A. 31253 0 N.A. N.A. 8.3
3/16" 31015 4 6 .72 31515 9 N.A. N.A. 31256 1 N.A. N.A. 12
1/4" 31020 8 6 1.32 31520 3 6 2.64 31259 2 6 3.96 22
5/16" 31025 3 6 1.98 31525 8 6 3.96 31262 2 6 5.94 33
3/8" 31030 7 6 2.88 31535 7 6 5.76 31265 3 6 8.64 48
7/16" 31035 2 3 1.95 31540 1 3 3.90 31268 4 3 5.85 65
1/2" 31040 6 3 2.55 31545 6 3 5.10 31271 4 3 7.65 85
9/16" 31045 1 3 3.24 31550 0 3 6.48 31274 5 3 9.72 108
5/8" 31050 5 3 3.99 31555 5 3 7.98 31277 6 3 11.97 133
11/16" 31055 0 3 4.80 31560 9 3 9.60 31280 6 3 14.40 160
3/4" 31060 4 3 5.70 31565 4 3 11.40 31283 7 3 17.10 190
13/16" 31065 9 3 6.75 31570 8 3 13.50 31286 8 3 20.25 225
7/8" 31070 3 3 7.80 31575 3 3 15.60 31289 9 3 23.40 260
1" 31075 8 3 10.2 31580 7 3 20.40 31292 9 3 30.60 340

NOTE: Standard carton quantities shown for information purposes. Standard

bundle quantities should be observed.

CHICAGO SSQUARE
CHICAGO QUAR E KEYSTOCK
KE YS T OCK DISPLAY
DIS PLAY
PART
Part ## 60150
601504 4
Contains the Following
Zinc Plated Sizes
12" Lengths Square Keystock:
12 Each: 1/8", 5/32", 3/16", 1/4", 5/16", 3/8"
6 Each: 7/16", 1/2"
Shipping Weight 36 lbs.

SLOTTED ANGLES
Stock Estimated
Bundle Carton Weight Two sizes of framing
Part Length Weight Weight Per 100 materials, .074" for
Size Quantity Quantity Feet (lbs)
No. Inches (lbs) (lbs) light duty and .080" for
.074" x 1-1/2" x 1-1/2" 31705 4 36" 12 25 36 75 69 standard applications,
.074" x 1-1/2" x 1-1/2" 31710 8 48" 12 33 12 33 69 are offered as Angles.
.074" x 1-1/2" x 1-1/2" 31715 3 60" 12 42 12 42 69 Easily assembled with
.074" x 1-1/2" x 1-1/2" 31720 7 72" 12 50 12 50 69 5/16" x 3/4" hex head
.074" x 1-1/2" x 1-1/2" 31725 2 120" 12 84 12 84 69 bolts with nuts –
.074" x 1-1/2" x 1-1/2" 31730 6 144" 12 100 12 100 69 storage racks, tables,
.080" x 2-1/4" x 1-1/2" 31735 1 72" 6 33 12 66 93 benches and carts to
.080" x 2-1/4" x 1-1/2" 31740 5 120" 6 56 6 56 93
cite a few end uses.
.080" x 2-1/4" x 1-1/2" 31745 0 144" 6 67 6 67 93

SLOTTED FLATS
Stock Estimated
Bundle Carton Weight
Part Length Weight Weight Per 100
For use in tensioning Size Quantity Quantity Feet (lbs)
No. Inches (lbs) (lbs)
angles, load dividers .080" x 1-3/8" 29705 9 36" 5 5.2 90 94 35
or hangers. .080" x 1-3/8" 29710 3 48" 5 7 50 70 35
.080" x 1-3/8" 29715 8 60" 5 8.6 50 86 35
.080" x 1-3/8" 29720 2 72" 5 10.4 50 105 35

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 43

 ZINC PLATED* STEEL “SHAPES”
* Also available in self-colored finish for welding.

Diameters 3/16" to 3/4" inclusive are cold drawn steel. Produced to cold finish tolerances.
7/8" and 1" rounds are Hot Rolled. 72", 120" and 144" lengths are also available.
ROUNDS Stock Estimated
Bundle Carton Weight
Diameter Color Part Length Weight Weight Per 100
Quantity Quantity Feet (lbs)
or Size Code No. Inches (lbs) (lbs)
3/16" Green 28105 8 36" 5 1.4 200 56 9.4
1/4" Blue 28110 2 36" 5 2.5 170 85 16.7
5/16" Red 28115 7 36" 5 3.9 110 86 26.1
3/8" Yellow 28120 1 36" 5 5.6 75 84 37.6
7/16" Green 28125 6 36" 5 7.7 55 85 51.1
1/2" Blue 28130 0 36" 5 11 40 80 66.8
5/8" Red 28135 5 36" 3 9.4 27 85 104.3
3/4" Yellow 28140 9 36" 3 13.5 18 81 150.2
7/8" Green 28145 4 36" 3 18.2 15 91 204
1" Red 28150 8 36" 3 24 12 96 267

Some sizes are available in stainless steel on a special basis.

FLATS Stock Estimated

Stock Bundle Carton Weight
Sizes Part Weight Weight Per 100
& Lengths Quantity Quantity Feet (lbs)
No. (lbs) (lbs)
Produced from Mild 1/8" x 3/4" x 36" 29105 7 5 4.8 90 86 31.9
Carbon Cold Finished 1/8" x 3/4" x 48" 29110 1 5 6.4 70 90 31.9
Steel with Round Edges. 1/8" x 3/4" x 72" 29120 0 5 9.6 45 86 31.9
12 foot maximum length 1/8" x 1" x 36" 29125 5 5 6.4 70 90 42.5
available. 1/8" x 1" x 48" 29130 9 5 8.5 50 85 42.5
1/8" x 1" x 72" 29140 8 5 12.8 35 90 42.5
1/8" x 1-1/4" x 36" 29145 3 5 7.1 50 80 53.1
1/8" x 1-1/4" x 48" 29150 7 5 10.6 40 85 53.1
1/8" x 1-1/4" x 72" 29160 6 5 15.9 25 80 53.1

Zinc Plated Mild Carbon Steel.

ANGLES Stock Estimated
Stock Bundle Carton Weight NOTE:
Sizes Part Weight Weight Per 100 Standard
& Lengths Quantity Quantity Feet (lbs)
No. (lbs) (lbs) carton
1/8" x 3/4" x 3/4" x 36" 30105 3 3 5.3 36 64 59 quantities
1/8" x 3/4" x 3/4" x 48" 30110 7 3 7.1 24 57 59 shown for
1/8" x 3/4" x 3/4" x 60" 30115 2 3 8.9 24 71 59 information
1/8" x 3/4" x 3/4" x 72" 30120 6 3 10.6 24 85 59 purposes.
1/8" x 1" x 1" x 36" 30125 1 3 7.2 30 72 80 Standard
1/8" x 1" x 1" x 48" 30130 5 3 9.6 18 58 80 bundle
1/8" x 1" x 1" x 60" 30135 0 3 12 18 72 80 quantities
1/8" x 1" x 1" x 72" 30140 4 3 14.4 18 86 80 should be
1/8" x 1-1/4" x 1-1/4" x 36" 30145 9 3 9.1 24 73 101 observed.
1/8" x 1-1/4" x 1-1/4" x 48" 30150 3 3 12.1 15 61 101
1/8" x 1-1/4" x 1-1/4" x 60" 30155 8 3 15.1 15 76 101
1/8" x 1-1/4" x 1-1/4" x 72" 30160 2 3 18.1 15 91 101
3/16" x 2" x 2" x 36" 30165 7 3 21.9 6 44 244 Made in U S A
3/16" x 2" x 2" x 48" 30170 1 3 29.2 6 59 244
3/16" x 2" x 2" x 60" 30175 6 3 36.6 6 73 244
3/16" x 2" x 2" x 72" 30180 0 3 43.9 6 88 244

44 Chicago Hardware and Fixture Company Since 1912

 BRASS ROUNDS, FLATS & ANGLES
BRASS ROUNDS
72", 120" and 144" lengths are also available from stock; intermediate lengths on a
special basis.
Stock Estimated
Bundle Carton Weight
Diameter Part Length Weight Weight Per 100
Quantity Quantity
or Size No. Inches (lbs) (lbs) Feet (lbs)
3/16" 28005 1 36" 5 1.5 170 51 10.2
1/4" 28010 5 36" 5 2.7 170 92 18.1
5/16" 28015 0 36" 5 4.2 110 92 28.3
3/8" 28020 4 36" 5 6.1 75 92 40.7
7/16" 28025 9 36" 5 8.3 55 92 55.4
1/2" 28030 3 36" 5 10.8 40 86 72.3
5/8" 28035 8 36" 3 10.1 27 91 113
3/4" 28040 2 36" 3 14.6 18 88 163

BRASS FLATS
Lengths, in addition to those listed below, can be supplied up to 144".
Stock Estimated
Stock Bundle Carton Weight
Sizes Part Weight Weight Per 100
Quantity Quantity
& Lengths No. (lbs) (lbs) Feet (lbs)
1/8" x 3/4" x 36" 29005 0 5 5.2 90 94 34.5
1/8" x 3/4" x 48" 29010 4 5 6.9 70 97 34.5
1/8" x 3/4" x 72" 29020 3 5 10.4 45 94 34.5
1/8" x 1" x 36" 29025 8 5 6.9 70 97 46.1
1/8" x 1" x 48" 29030 2 5 9.2 50 92 46.1
1/8" x 1" x 72" 29040 1 5 13.8 35 97 46.1
1/8" x 1-1/4" x 36" 29045 6 5 8.6 50 86 57.6
1/8" x 1-1/4" x 48" 29050 0 5 11.5 40 92 57.6
1/8" x 1-1/4" x 72" 29060 9 5 13.8 25 86 57.8

BRASS ANGLES
For Structural and Marine repair applications which require non-ferrous metals.
Maximum length available 144".
Stock Estimated
Stock Bundle Carton Weight
Sizes Part Weight Weight Per 100
& Lengths Quantity Quantity Feet (lbs)
No. (lbs) (lbs)
1/8" x 3/4" x 3/4" x 36" 30005 6 3 5.6 36 67 62.9
1/8" x 3/4" x 3/4" x 48" 30010 0 3 7.5 24 60 62.9
1/8" x 3/4" x 3/4" x 60" 30015 5 3 9.4 24 75 62.9
1/8" x 3/4" x 3/4" x 72" 30020 9 3 11.3 24 90 62.9
1/8" x 1-1/4" x 1-1/4" x 36" 30045 2 3 9.8 24 78 109
1/8" x 1-1/4" x 1-1/4" x 48" 30050 6 3 13 15 65 109
1/8" x 1-1/4" x 1-1/4" x 60" 30055 1 3 16.3 15 82 109
1/8" x 1-1/4" x 1-1/4" x 72" 30060 5 3 19.6 15 98 109 Made in U S A

NOTE: Standard carton quantities shown for information purposes.

Standard bundle quantities should be observed.

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 45

 FULL-SIZE STEEL CENTER DISPLAY
Made in U S A
FULL-SIZE STEEL CENTER ............. Part No. 60060 6
Shipping Weight .......... 586 lbs.

Display Contains the Following:

24” ZINC PLATED 36” ZINC PLATED

THREADED ROD ROUNDS
No. Part No. Part
Size Pcs. No. Size Pcs. No.
1/4" - 20 15 35088 4 3/16" 10 28105 8
5/16" - 18 15 35108 9 1/4" 10 28110 2
3/8" - 16 15 35128 7 5/16" 10 28115 7
1/2" - 13 15 35168 3 3/8" 10 28120 1
5/8" - 11 6 35208 6 1/2" 5 28130 0
3/4" - 10 6 35228 4 5/8" 3 28135 5

36” ZINC PLATED ZINC PLATED

THREADED ROD SLOTTED ANGLES
No. Part No. Part
Size Pcs. No. Size Pcs. No.
1/4" - 20 20 35091 4 .074" x 1-1/2" x 1-1/2" x 36" 6 31705 4
5/16" - 18 20 35111 9 .074" x 1-1/2" x 1-1/2" x 48" 6 31710 8
3/8" - 16 20 35131 7 .074" x 1-1/2" x 1-1/2" x 72" 6 31720 7
1/2" - 13 10 35171 3 .080" x 2-1/4" x 1-1/4" x 72" 6 31735 1
5/8" - 11 6 35211 6
3/4" - 10 6 35231 4

72” ZINC PLATED ZINC PLATED

THREADED ROD ANGLES
No. Part No. Part
Size Pcs. No. Size Pcs. No.
1/4" - 20 6 35094 5 1/8" x 3/4" x 3/4" x 36" 6 30105 3
5/16" - 18 6 35114 0 1/8" x 3/4" x 3/4" x 72" 3 30120 6
3/8" - 16 6 35134 8 1/8" x 1" x 1" x 36" 6 30125 1
1/2" - 13 6 35174 4 1/8" x 1" x 1" x 72" 3 30140 4
5/8" - 11 3 35214 7 1/8" x 1-1/4" x 1-1/4" x 36" 3 30145 9
3/4" - 10 3 35234 5 1/8" x 1-1/4" x 1-1/4" x 72" 3 30160 2

12” ZINC PLATED Display Stand Dimensions:

65” High
KEY STOCK 16-1/2” Wide
ZINC PLATED
No. Part 21” Deep (at the base)
Size Pcs. No.
FLATS
1/8" 12 31005 5 No. Part
5/32" 12 31010 9 Size Pcs. No.
3/16" 12 31015 4 1/8" x 3/4" x 36" 5 29105 7
ZINC PLATED
1/4" 12 31020 8 1/8" x 3/4" x 72" 5 29120 0 SLOTTED FLATS
5/16" 12 31025 3 1/8" x 1" x 36" 5 29125 5 No. Part
3/8" 12 31030 7 1/8" x 1" x 72" 5 29140 8 Size Pcs. No.
7/16" 6 31035 2 1/8" x 1-1/4" x 36" 5 29145 3 .080" x 1-3/8" x 36" 5 29705 9
1/2" 6 31040 6 1/8" x 1-1/4" x 72" 5 29160 6 .080" x 1-3/8" x 72" 5 29720 2

One Foot Threaded Rod Display can be substituted for Key Stock.

46 Chicago Hardware and Fixture Company Since 1912

 STAINLESS STEEL SECTION
THIMBLES Made in U S A
TYPE 304 STAINLESS STEEL
Rope Part Weight
Diameter No. Per 100
1/8" 22305 8 2.1
3/16" 22310 2 2.1
1/4" 22315 7 3.4
5/16" 22320 1 4.6
3/8" 22325 6 9
1/2" 22335 5 17
See page 13 for additional
dimensional information. DROP FORGED EYE BOLTS
TYPE 316 STAINLESS STEEL
Regular Shoulder
Diameter &
Part Weight Part Weight
Shank
No. Per 100 No. Per 100
Length
1/4" x 2" 08205 1 6.4 08605 9 7.4
1/4" x 3" 08208 2 8 N.A. N.A.
1/4" x 4" 08211 2 9.3 08611 0 10.7
1/4" x 5" 08214 3 10.4 N.A. N.A.
1/4" x 6" 08217 4 11.8 N.A. N.A.
5/16" x 2-1/4" 08222 8 12.7 08622 6 12.9
5/16" x 3-1/4" 08225 9 15 N.A. N.A.
5/16" x 4-1/4" 08228 0 16.5 08628 8 16.8
3/8" x 2-1/2" 08239 6 19.2 08639 4 21
3/8" x 4-1/4" 08245 7 24.4 08645 5 29
Regular Shoulder 1/2" x 3-1/4" 08262 4 46 08662 2 46
1/2" x 6" 08268 6 60 08668 4 63
5/8" x 4-1/2" 08282 2 79 08682 0 99

See pages 14-15 for additional dimensional information.

STAINLESS STEEL SECTION

WIRE ROPE CLIPS
TYPE 304 STAINLESS STEEL
Stock Rope Part Weight
No. Size No. Per 100
2 1/16" - 3/32" 23605 8 5
4 1/8" - 5/32" 23610 2 7
6 3/16" - 7/32" 23615 7 11
8 1/4" - 5/16" 23620 1 18
10 3/8" 23630 0 38
12 7/16" - 1/2" 23635 5 55

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 47

 STAINLESS STEEL SECTION

Made in U S A

MACHINERY EYE BOLTS

SHOULDER PATTERN – THREADED
TYPE 316 STAINLESS STEEL
Shoulder Bolt Shank Part Weight
Pattern No. Diameter Length No. Per 100
21SS 1/4" 1" 13105 6 6
22SS 5/16" 1-1/8" 13125 4 10
23SS 3/8" 1-1/4" 13145 2 16
25SS 1/2" 1-1/2" 13185 8 38
27SS 5/8" 1-3/4" 13225 1 73.5
Shoulder
28SS 3/4" 2" 13248 0 99.5
See page 18 for additional dimensional information.

MACHINERY EYE BOLTS

PLAIN PATTERN – THREADED
TYPE 316 STAINLESS STEEL
Plain Bolt Shank Part Weight
Pattern No. Diameter Length No. Per 100
1SS 1/4" 1" 14205 2 5
2SS 5/16" 1-1/8" 14210 6 10.5
3SS 3/8" 1-1/4" 14215 1 15.5
5SS 1/2" 1-1/2" 14220 5 33
7SS 5/8" 1-3/4" 14225 0 64
Plain 8SS 3/4" 2" 14230 4 90.5

DROP FORGED BLANK ROD ENDS REGULAR

TYPE 316 STAINLESS STEEL DROP FORGED EYE NUTS
Stock Part Diameter *Length Weight TYPE 316 STAINLESS STEEL
No. No. Inches Inches Per 100
C-134SS-A 18555 4 1/4" 6" 11
Drilled & Tapped
C-135SS-A 18560 6 5/16" 6" 18 Weight
Bail Size Tap Size Part No.
C-217SS 18535 6 3/8" 3" 14 Per 100
C-138SS 18565 3 1/2" 6" 47 1/4" 1/4" - 20 16505 1 8.2

C-139SS 18585 1 5/8" 6" 77.5 1/4" 5/16" - 18 16510 5 8

C-140SS 18605 6 3/4" 6" 112 3/8" 3/8" - 16 16520 4 34

C-141SS 18615 5 7/8" 6" 164 3/8" 1/2" - 13 16525 9 29.3

* Measured from center of boss 1/2" 5/8" - 11 16530 3 61.5

See page 29 for additional dimensional information. 5/8" 3/4" - 10 16535 8 103
See page 27 for additional
dimensional information.

48 Chicago Hardware and Fixture Company Since 1912

 STAINLESS STEEL SECTION

Made in U S A

TURNED EYE BOLTS – MACHINE THREAD

TYPE 304 STAINLESS STEEL
Stock Thread Part Shank Weight Stock Thread Part Shank Weight
No. Diameter No. Length Per 100 No. Diameter No. Length Per 100
A-1SS 1/8" (6-32) 07255 7 3/4" .75 F-4SS 5/16"-18 07360 8 3" 11
B-1SS 5/32" (8-32) 07260 1 1-1/8" 1.31 F-5SS 5/16"-18 07365 3 3-1/2" 11
C-1SS 3/16" (10-24) 07265 6 1" 1.81 F-6SS 5/16"-18 07370 7 4" 12
C-2SS 3/16" (10-24) 07270 0 1-3/8" 1.875 F-7SS 5/16"-18 07375 2 5" 14
C-3SS 3/16" (10-24) 07275 5 2" 2.375 F-8SS 5/16"-18 07380 6 6" 15
C-4SS 3/16" (10-24) 07280 9 3" 2.94 F-9SS 5/16"-18 07385 1 6-1/2" 18
E-1SS 1/4"-20 07290 8 1" 3.75 G-1SS 3/8"-16 07390 5 1" 12
E-2SS 1/4"-20 07295 3 1-1/2" 4.375 G-2SS 3/8"-16 07395 0 2" 15
E-2SS-A 1/4"-20 07300 4 1-7/8" 5.2 G-2SS-A 3/8"-16 07400 1 2-1/2" 15.7
E-3SS 1/4"-20 07305 9 2" 5 G-3SS 3/8"-16 07405 6 2-1/2" 15.5
E-4SS 1/4"-20 07310 3 2-1/2" 5.6 G-4SS 3/8"-16 07410 0 3" 17
E-5SS 1/4"-20 07315 8 3" 6.3 G-5SS 3/8"-16 07415 5 3-1/2" 18
E-6SS 1/4"-20 07320 2 3-1/2" 6.9 G-6SS 3/8"-16 07420 9 4" 21
E-7SS 1/4"-20 07325 7 4" 7.5 G-7SS 3/8"-16 07425 4 5" 22
E-8SS 1/4"-20 07330 1 5" 8 G-8SS 3/8"-16 07430 8 6" 24
E-9SS 1/4"-20 07335 6 6" 9 G-9SS 3/8"-16 07435 3 8" 30
F-1SS 5/16"-18 07340 0 1" 7 J-1SS 1/2"-13 07460 5 2" 33
F-2SS 5/16"-18 07345 5 2" 9 J-2SS 1/2"-13 07465 0 4" 41
F-2SS-A 5/16"-18 07350 9 2-1/4" 9.7 J-3SS 1/2"-13 07470 4 6" 50
F-3SS 5/16"-18 07355 4 2-1/2" 10 J-4SS 1/2"-13 07475 9 8" 58

See page 37 for additional dimensional information.

S-HOOKS – TYPE 304 STAINLESS STEEL

Dimensions – Inches Weight Working
Stock Part Wire Overall Hooks Opening Per 100 Load
No. No. Diameter Length Inside Dia. Hooks (lbs) Limit (lbs)
S-1SS 06211 4 .080" 3/4" 1/4" 1/8" .26 7
S-1SS-A 06213 8 .105" 1" 5/16" 5/32" .55 16
S-2SS 06214 5 .114" 1-1/4" 3/8" 3/16" .83 17
S-2SS-A 06215 2 .148" 1-1/2" 7/16" 7/32" 1.62 26
S-3SS 06217 6 .186" 1-3/4" 1/2" 1/4" 2.97 40
S-4SS 06220 8 .220" 2-1/8" 5/8" 5/16" 5.15 58
S-5SS 06223 7 .250" 2-1/2" 3/4" 7/16" 7.5 70
S-6SS 06226 8 .312" 3" 7/8" 1/2" 13.9 132
S-7SS 06229 9 .375" 3-1/2" 1" 1/2" 23.44 170

See page 31 for additional dimensional information.

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 49

 STAINLESS STEEL SECTION
Made in U S A

ROUND BEND U-BOLTS – TYPE 304 STAINLESS STEEL

Stainless Steel U-Bolts Stainless Steel U-Bolts
& 2 Nuts Plates & 2 Nuts
Dimensions Pipe Stock Part Weight Stock Part Weight
U-Bolts Only (A x C x B) Size No. No. Per 100 No. No. Per 100
1/4" x 9/16" x 1-1/4" 1/4" 01SS 50405 8 5 1SS 50605 2 7
1/4" x 3/4" x 1-1/4" 3/8" 02SS 50408 9 5 2SS 50608 3 7
1/4" x 3/4" x 2-1/4" 3/8" 03SS 50411 9 7 3SS 50611 3 9
1/4" x 1" x 1-3/4" 1/2" 04SS 50414 0 7 4SS 50614 4 9
1/4" x 1-1/8" x 2" 3/4" 05SS 50420 1 7 5SS 50620 5 9
1/4" x 1-1/4" x 2-1/4" 3/4" 06SS 50426 3 7.5 6SS 50626 7 10
1/4" x 1-1/2" x 2-3/4" 1" 07SS 50429 4 9 7SS 50629 8 12
1/4" x 1-3/4" x 3" 1-1/4" 08SS 50432 4 9 8SS 50632 8 12
1/4" x 2" x 3-1/4" 1-1/2" 09SS 50435 5 9.5 9SS 50635 9 14
5/16" x 1" x 2-3/16" 1/2" 010SS 50438 6 11 10SS 50638 0 14
5/16" x 1-3/8" x 2-3/16" 1" 011SS 50444 7 12 11SS 50644 1 15
5/16" x 1-1/2" x 2-3/16" 1" 012SS 50450 8 12 12SS 50650 2 15
5/16" x 1-3/4" x 2-11/16" 1-1/4" 013SS 50453 9 13 13SS 50653 3 17.5
5/16" x 2" x 2-11/16" 1-1/2" 014SS 50459 1 14 14SS 50659 5 19
5/16" x 2-1/2" x 3-3/16" 2" 015SS 50465 2 16 15SS 50665 6 21
5/16" x 3" x 3-11/16" 2-1/2" 016SS 50471 3 18 16SS 50671 7 24
3/8" x 1" x 2-1/4" 1/2" 017SS 50474 4 17.5 17SS 50674 8 22.5
3/8" x 1-1/4" x 2-1/4" 3/4" 018SS 50477 5 18 18SS 50677 9 24
3/8" x 1-1/2" x 2-1/2" 1" 019SS 50480 5 18.5 19SS 50680 9 26
3/8" x 1-3/4" x 2-3/4" 1-1/4" 020SS 50483 6 20 20SS 50683 0 27.5
3/8" x 2" x 2-5/8" 1-1/2" 021SS 50486 7 20 21SS 50686 1 29
3/8" x 2-1/2" x 3-1/8" 2" 022SS 50489 8 24.5 22SS 50689 2 33
3/8" x 3" x 3-5/8" 2-1/2" 023SS 50492 8 26 23SS 50692 2 38
3/8" x 3-1/2" x 4-1/8" 3" 024SS 50495 9 30 24SS 50698 4 42.5
1/2" x 3" x 4-1/2" 2-1/2" 025SS 50497 3 59 25SS 50701 1 71
1/2" x 3-1/2" x 5" 3" 026SS 50500 0 64 26SS 50704 2 78
1/2" x 4" x 5-1/2" 3-1/2" 027SS 50503 1 70 27SS 50710 3 87
1/2" x 4-1/2" x 6" 4" 028SS 50506 2 75 28SS 50713 4 92.5
1/2" x 5-5/8" x 7-1/4" 5" 029SS 50509 3 90 N.A. N.A. N.A.
1/2" x 6-3/4" x 8-3/8" 6" 030SS 50512 3 101 N.A. N.A. N.A.
1/2" x 8-3/4" x 10-3/8" 8" 031SS 50515 4 120 N.A. N.A. N.A.
*3/4" x 10-7/8" x 13-13/16" 10" 032SS 50560 4 440 N.A. N.A. N.A.
*7/8" x 12-7/8" x 16-1/16" 12" 033SS 50570 3 710 N.A. N.A. N.A.
*7/8" x 14-1/8" x 17-5/16" 14" 034SS 50574 1 755 N.A. N.A. N.A.
*7/8" x 16-1/8" x 19-5/16" 16" 035SS 50578 9 850 N.A. N.A. N.A.

*Full Stock Diameter with Cut Thread See pages 32-34 for additional
dimensional information.

50 Chicago Hardware and Fixture Company Since 1912

 STAINLESS STEEL SECTION
Made in U S A

ROUND BEND LONG TANGENT

U-BOLTS WITH 4 NUTS
TYPE 304 STAINLESS STEEL
Stock Part Pipe Inside Inside Thread Weight
No. No. Size Diameter (A) Width (C) Length (B) Length (T) Per 100
LT-BSS 51660 0 1/2" 1/4" - 20 7/8" 2-15/16" 2-1/2" 9
LT-CSS 51665 5 3/4" 1/4" - 20 1-1/8" 3-3/16" 2-1/2" 10
LT-DSS 51670 9 1" 1/4" - 20 1-3/8" 3-7/16" 2-1/2" 11
LT-1SS 51705 8 1/2" 3/8" - 16 15/16" 3" 2-3/8" 24
LT-2SS 51710 2 3/4" 3/8" - 16 1-1/8" 3-5/16" 2-3/8" 25.5
LT-3SS 51715 7 1" 3/8" - 16 1-3/8" 3-7/16" 2-3/8" 26.5
LT-4SS 51720 1 1-1/4" 3/8" - 16 1-11/16" 3-23/32" 2-3/8" 28
LT-5SS 51725 6 1-1/2" 3/8" - 16 2" 4" 2-1/2" 30
LT-6SS 51730 0 2" 3/8" - 16 2-7/16" 4-7/16" 2-1/2" 33
LT-7SS 51735 5 2-1/2" 1/2" - 13 2-15/16" 5-7/32" 3" 71
LT-8SS 51740 9 3" 1/2" - 13 3-9/16" 5-3/4" 3" 77
LT-9SS 51745 4 3-1/2" 1/2" - 13 4-1/16" 6-1/4" 3" 82
LT-10SS 51750 8 4" 1/2" - 13 4-9/16" 6-3/4" 3" 89
LT-11SS 51755 3 5" 1/2" - 13 5-5/8" 7-13/16" 3" 101
LT-12SS 51760 7 6" 5/8" - 11 6-3/4" 9-1/2" 3-3/4" 194.5
LT-13SS 51765 2 8" 5/8" - 11 8-3/4" 11-1/8" 3-3/4" 223.5
LT-14SS 51770 6 10" 3/4" - 10 10 -7/8" 13-13/16" 4" 460

See page 35 for additional dimensional information.

SQUARE BEND U-BOLTS

WITH 2 NUTS AND 2 WASHERS
TYPE 304 STAINLESS STEEL
Stock Part Diameter Inside Overall Thread Weight
No. No. (A) Width (C) Length (B) Length (T) Per 100
SB-1SS 51105 6 3/8" - 16 2" 3" 1-1/2" 25.5
SB-2SS 51110 0 3/8" - 16 2" 5" 3" 35.5
SB-3SS 51115 5 3/8" - 16 2" 7" 3-3/4" 44.5
SB-4SS 51120 9 3/8" - 16 4" 3" 1-1/2" 29.5
SB-5SS 51125 4 3/8" - 16 4" 5" 3" 40
SB-6SS 51130 8 3/8" - 16 4" 7" 3-3/4" 49.5
SB-7SS 51135 3 3/8" - 16 6" 5" 3" 44.5
SB-8SS 51140 7 3/8" - 16 6" 7" 3-3/4" 56
SB-9SS 51145 2 3/8" - 16 6" 9" 5-5/8" 63

See page 36 for additional dimensional information.

Chicago • Chino • Atlanta • Houston www.chicagohardware.com 51

 FORMED OR FORGED FITTINGS
The schematic drawings in adjoining columns represent basic rod or wire forms and steel eye
bolt forgings. Space does not permit the design illustrations of all parts that we are capable of
manufacturing.
A review of complete catalog literature will indicate an extensive listing of standard stock sizes of round bend
U-bolts, turned or formed eye bolts and forged steel eye bolts in several patterns.
When it is not feasible to utilize a standard product, we are prepared and equipped to manufacture requirements
to specification. Inquiries are solicited.
Variation in quantity: on special items we reserve the right to a maximum 10% variation for allowances in
manufacture.

Figure No. 1 Figure No. 2 Figure No. 3 Figure No. 4

Figure No. 5 Figure No. 6 Figure No. 7 Figure No. 8

Figure No. 9 Figure No. 10 Figure No. 11 Spade Bolt

52 Chicago Hardware and Fixture Company Since 1912

 INDEX
Item Page Item Page
–A– –K–
Alloy, (B7 4140) Threaded Rod . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Keystock, Square . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Alloy Steel Hoist Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 –L–
Anchor Shackles, Round Pin, Screw Pin & Safety . . . . . . . . . . . 9 Latch Kits for Hoist - Eye Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Angles, Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Lifting Eyes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Angles, Slotted Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
–M–
–B– Machinery Eye Bolts, Metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Bolts Machinery Eye Bolts, Plain Pattern & Shoulder . . . 18, 19, 20, 21
Eyes, Lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Machinery Eye Bolts, Stainless Steel . . . . . . . . . . . . . . . . . . . . . 48
Eyes, Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Metric Machinery, Eye Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Eye Drop Forged, Plain & Shoulder Pattern Machinery . . 18, 19, 21
Eye Drop Forged, Zinc-Plated, Hot Galvanized, Plain & –N–
Shoulder Machinery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Nuts, Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Eye Drop Forged, Shoulder & Plain Pattern Machinery Nuts, Eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27, 28
Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Nuts, Eye, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Eye Drop Forged Stainless Steel Regular & Shoulder Nut . . . 47 –P–
Eye Drop Forged Galvanized Regular & Shoulder Nut . . . . 14, 15 Pins, Clevis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Eye Drop Forged Galvanized Regular & Shoulder Screw . . . . 15 Pins, Clevis SAE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Regular & Shoulder Nut Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Pad Eyes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Regular & Shoulder Screw Ring . . . . . . . . . . . . . . . . . . . . . . . . . 17 –R–
Rod Ends, Blank and Black Oxide . . . . . . . . . . . . . . . . . . . . . . . 29
Ring Bolts, Drop Forged, Galvanized Regular & Shoulder Nut 16
Rod Ends, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Ring Bolts, Drop Forged, Galvanized Regular & Shoulder Screw 17
Turned Eye, Machine, Lag & Welded . . . . . . . . . . . . . . . . . . 37, 38
Rod, Threaded, Self Colored, Zinc Plated, Galvanized
Turned Eye, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
& Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39, 40, 41, 42
U-Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32, 33, 34, 35, 36
Rod Ends, Drop Forged Blank, Black Oxide . . . . . . . . . . . . . . . . . 29
U-Bolts, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50, 51
Rod Ends, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
U-Bolts, Hot Dip Galvanized . . . . . . . . . . . . . . . . . . . . . . 33, 35, 36
Rod Ends, Turnbuckle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
U-Bolt, Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Rounds, Unthreaded Rod, Brass & Steel . . . . . . . . . . . . . . . . . 44, 45
Brass Rounds, Flats & Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Round Pin, Anchor & Chain Shackles . . . . . . . . . . . . . . . . . . . . 9, 10
Brass Threaded Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
–C– –S–
Chain Shackles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Safety Snap Hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Chain Swivels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Safety Swivel Hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Clips, Wire Rope, Forged & Malleable . . . . . . . . . . . . . . . . . . . 11, 12 S-Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Clips, Wire Rope, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . 47 S-Hooks, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Clevis Grab Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Shackles
Clevis Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Round Pin, Anchor & Chain . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 10
Clevis Pins, SAE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Safety, Anchor & Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 10
Coupling Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Screw Pin, Anchor & Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 10
Slotted Angles, Zinc Plated Steel . . . . . . . . . . . . . . . . . . . . . . . . . . 43
–D– Slotted Flats, Zinc Plated Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Displays Square Keystock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Full-Size Steel Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Stainless Steel
Midget Aluminum Turnbuckles . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Eye Bolts, Regular & Shoulder Nut . . . . . . . . . . . . . . . . . . . . . . 47
Zinc Plated One Foot Threaded Rod . . . . . . . . . . . . . . . . . . . . . 42 Machinery Eye Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Square Keystock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Rod Ends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Turned Eye Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 S-Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
U-Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Threaded Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
–E– Turned Eye Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Eye Bolts U-Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50, 51
Machinery, Metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Wire Rope Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Machinery, Plain & Shoulder Pattern . . . . . . . . . . . . . . . 18, 19, 21 Wire Rope Thimbles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Machinery, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Stub End Turnbuckles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Machinery, Zinc Plated & Hot Galvanized . . . . . . . . . . . . . . . . . 20 Swivels
Regular & Shoulder Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 15 Eye & Eye, Jaw & Eye, Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Regular & Shoulder Nut, Stainless Steel . . . . . . . . . . . . . . . . . . 47 –T–
Regular & Shoulder Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Thimbles, Wire Rope Regular & Heavy Duty . . . . . . . . . . . . . . . . . 13
Regular & Shoulder Nut Rings Bolts . . . . . . . . . . . . . . . . . . . . . 16 Thimbles, Wire Rope Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . 47
Regular & Shoulder Screw Ring Bolts . . . . . . . . . . . . . . . . . . . . 17 Threaded Rod Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Turned, Machine Thread, Lag & Welded . . . . . . . . . . . . . . . 37, 38 Threaded Rod, Brass, Stainless Steel, B-7,
Turned, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Self-Colored, Zinc Plated & Hot Dip Galvanized . . . 39, 40, 41, 42
Eye Hoist Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Tiller Rope Clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Eye Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27, 28 Turnbuckles, Aluminum, Midget . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Eye Nuts, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Turnbuckles, Midget Aluminum Display . . . . . . . . . . . . . . . . . . . . . . 8
Eye, Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Turnbuckles, Drop Forged . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 5, 6, 7
Eye & Eye Swivels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Turnbuckles, Malleable, Midget . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Eye & Eye Turnbuckles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Turned Eye Bolts, Machine & Lag Thread . . . . . . . . . . . . . . . . 37, 38
–F– Turned Eye Bolts, Welded Eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Flats, Zinc Plated Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Turned Eye Bolt Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Flats, Zinc Plated Slotted Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Turned Eye Bolts, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . 49
Flats, Brass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 –U–
–H– U-Bolts, Zinc Plated Round Bend,
Hoist Rings, Alloy Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Square Bend, Long Tangent . . . . . . . . . . . . . . . . . . . . . . 32, 35, 36
Hook Clevis Grab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 U-Bolt Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Hook & Eye Turnbuckles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 U-Bolts Hot Dip Galvanized . . . . . . . . . . . . . . . . . . . . . . . . 33, 35, 36
Hook & Hook Turnbuckles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 U-Bolts Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50, 51
Hooks, Hoist, Eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Hooks, S- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
–W–
Hook, Safety Snap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Washers, Bevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Hooks, Safety Swivel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Wire Rope Clips, Drop Forged & Malleable . . . . . . . . . . . . . . . 11, 12
Wire Rope Clips, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . 47
–J– Wire Rope Thimbles, Regular & Heavy Duty . . . . . . . . . . . . . . . . . 13
Jaw & Eye Swivels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Wire Rope Thimbles, Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . 47
Jaw & Eye Turnbuckles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Jaw & Jaw Turnbuckles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 –Y–
Yoke Ends, Adjustable & Plain . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30