Strong Front and Rear chassis braces.

Tuned Polished Dual Chamber racing pipe.

Unique adjustable chassis width of 310mm or 330mm.
INSTRUCTION MANUAL
High performance .26 engine with Shaft Start Motor handle.
Full race Offset King Pin aluminum steering knuckle.
Three sealed differentials with 6 steel gears.
Racing X-Equal tires and V-spoke wheels.
Adjustable Front and Rear roll bars.
Multi disc brakes with adjustable bias.
Hard Coated Threaded body oil fill shocks.
5 Degree hard coated 3mm chassis.
Racing 3 shoe clutch with Aluminum CNC flywheel.
Steel main spur gear and center differential.
Adjustable servo saver.
Front CVA joint and 8mm axles.
140+cc fuel tank with inside stone filter.
 RTR KITS - REQUIRED FOR OPERATION
THINGS NEEDED You will need to buy a few items to start the engine and run the car.
• Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will
over heat engine.

• Buy LONG glow plugs, like OFNA/PICCO Plug (#51007 or 51008).

Use plugs without idle bar. Do NOT use plugs, like the MC-59 or OS-8

In your box you will find..

• #10163 - Bottle, spout top
• #10219 - Red “D” size glow heater
Glow Fuel
20%

You need to get batteries for the radio transmitter and the car receiver packs.
• Radio TX needs (8) eight AA batteries.
• Car needs (4) four AA Ni-cad batteries 2000Mah OFNA #10196 or (4) Alkaline.,
Alkaline type batteries will work, but braking will be reduced and 30 minute life. The
AA Batteries ( 12 pcs ) best for car, is to use a 5 cell hump receiver pack for increased voltage and longer
life..

Recommended Option:
You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5 cell
type(600AE). This will give more run time. OFNA #10212 1200NiMh Hump Pack and 10214
#10212 NiHm Hump Pack, NiHm Battery Charger #10214 Over-nite
see charger 10214. Charger

TOOLS NOT INCLUDED IN KIT,

BUT NEEDED TO MAINTAIN YOUR CAR.

Instant Cement
Cutter

Phillips Type Screw Drivers ( L )

Curved Scissors
#91009 $5.95
Grease

Cross Wrench
Phillips Type Screw Drivers ( S ) #17109 $3.95

Needle Nose Pliers

Glow Plug & 17MM Cross Wrench

#10801 $6.95
Knife
 MUST READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe • Clean oil and dirt from chassis with a degreaser.
and good experience you must observe a few rules. This
Precautions
kit is extremely fast, easily over 40MPH, and can seriously
• This kit is not a toy. Always run car with a second
injure someone if you are not careful.
person as a spotter and pitman.
Where to run car?
• Hot Parts - The pipe, manifold, engine and head are very
• Any running area you choose must be dry. Do not run
hot and will cause burns.
car near any water or wet dirt.
• Do not run on public streets. It is very easy to have the
• Rotating Parts - Keep hands away from the drive train,
car run over or damaged by hitting the curb.
wheels, and engine when engine is running.
• Do not operate car in tight confined places. The car is
very fast and will easily hit something. • Radio - Check batteries life before running the car. If
• Do not run near people or animals. The car is very fast
radio does not have full control of the car with steering
and will too easily hit someone.
and/or throttle/brake do not run until corrected. Failure to
• Due noise, you will want to consider the surrounding
correct this will result in possible injury and damage to the
area when operating the car.
• Do not operate the car at night. You will not be able to car or property.
drive it without hitting something.
• Glow fuel - Do leave the glow fuel unattended with the lid
• Do not operate the car indoors. Engine exhaust is not
off. Fuel contains Methanol and Nitro Methane and is
healthy.
flammable and poisonous.
Glow Fuel
• Glow fuel is poisonous! Store fuel in cool ventilated location. Refer the glow fuel
• Glow fuel is flammable! label for additional precautions.
• Do not leave in fuel bottle with lid off at any time.
• Do not use any fuel other than glow fuel in this engine. • Car Fuel tank - Never store fuel in car tank, it will ruin the
engine if left in tank.
First Time Starting the Engine
Caution! When starting engine make sure the following is • Always turn off the car BEFORE turning off radio.
observed.
• Set engine Master needle to 3 turns (rich setting) • DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY
• Do not do this alone, get an experienced friend to help at ISSUE.
first.
• Fill fuel tank, try not to spill fuel. Do not spill fuel on IF YOU DO NOT BREAK-IN ENGINE
receiver
• Hold car off the ground, so it will not runaway when first CORRECTLY, MAINLY AT LOW RPM,
starts YOU WILL BREAK THE CONNECTING
• Turn on Radio and check the linkage before starting
engine. ROD!
• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt
out. FAILURE TO NOT READ AND
Engine Break-in FOLLOW BREAK-IN ENGINE
• See Engine Page.

Emergency Stopping Engine When Running

INSTRUCTIONS WILL VOID
• Remove air filter and cover carb. intake.
• Squeeze fuel line and hold until engine stops.
WARRANTY!
• With a rag, cover exhaust outlet.

Storing Car After Running

• Remove fuel from tank and fuel lines
• Turn off radio in car
• Put a few drops of after run in engine to keep it from
rusting.
 NON-RTR OR PRO KITS - REQUIRED FOR OPERATION
THINGS NEED BESIDES THE KIT

3.5 cc (21 Class) ENGINE

REAR EXHAUST

OFNA/Picco
O-1 bp
#51217
Glow Plug Heat with Battery & Charger
Glow Fuel # 10227....$$19.95
20% (please note OFNA Glow Heats available)

Bottle’s with spout

# 10160 - large 500cc
# 10161 - large 500 ccAuto Stop
# 10162 - small 250cc
# 10164 - CNC spout 500CC
# 10167 - CNC spout 800CC

Off-Road Starter Box, 12V motor 12V Battery for Starter Box
(must have)
# 10250 - 1/8 scale Starter Box
# 10253 - 1/8 scale Starter Box w/ Panel
Off-Road Starter Box, two 550 motors
# 10248 - 1/8 scale Starter Box
# 10249 - 1/8 scale Starter Box,RTR
Optional Parts
Note: Pro kit does not include engine! # 92571 - Power Panel Glow Heater
# 92572 - Cable for Glow Plug
AA Batteries ( 12 pcs ) for radio

More Optional Parts . . .

Radio must be set at neutral position
RADIO CONTROL UNIT before installing in the kit.
#10211 NiHm Battery Flat
SEQUENCE TO SET NEUTRAL Pack .. $29.95
Install AA batteries in Radio.

Extend the antenna.(Transmitter)

Install batteries into Car receiver .

After installing the battery, connect the

battery box.
# 10214 NiHm Battery Pack
Extend the antenna. (Receiver) Charger.. $7.95
Set the trim-lever at center.

Turn on the switch. (Transmitter)

Note: Carefully read the instruction manual of your
2 channel radio controller before using. Turn on the switch. (Receiver)

Make sure the servos are in command.

SUITABLE SERVO SIZE When the operation stick is in neutral, # 51007 or 08 OFNA/Picoo
servo horns must be in neutral as will.
1mm *Adjustment can be made by re- Glow Plug .. $4.95
3 6mm-4 installing the servo horn.
15mm - 21mm
Turn off the switch. (Receiver)
11
29mm - 42mm Turn off the switch. (Transmitter)
12
Retract the antenna. (Transmitter)
13

TOOLS NOT INCLUDED IN KIT INCLUDED WITH KIT

Instant Cement Shock Oil

Cutter

Grease Box
Phillips Type Screw Drivers ( L )

Curved Scissors
5mm
Masking Tape Hex Wrench

Brush 3mm
Hex Wrench
Cross Wrench
Phillips Type Screw Drivers ( S ) #17109 $3.95

2.5mm
Hex Wrench

1.5mm
Needle Nose Pliers Paints Hex Wrench

Glow Plug & 17MM Cross Wrench

#10801 $6.95
Knife
Grease 7mm and 5.5mm
Hex Wrench
 PLASTIC PARTS
40017 40003
GEAR BOX PLASTIC PARTS DIFF. CASE
PLASTIC PARTS

40015
ARM HOLDER PLASTIC PARTS

1 3

40027 40013 & 40048

WING SUPPORT PLASTIC PARTS FRONT BUMPER & BATTERY HOLDER
PLASTIC PARTS
 PLASTIC PARTS
40031 40047
SERVO SAVER PLASTIC PARTS RECEIVER BOX PLASTIC PARTS

40040
CENTER DIFF. MOUNT PLASTIC PARTS

40018/40029 40046
CHASSIS BRACE PLASTIC PARTS STONE GUARD PLASTIC PARTS

40029 40029

40065 40019
40065

40018

40056
SHOCK ABSORBER PLASTIC PARTS
 ASSEMBLY OF THE THROTTLE LINKAGE SYSTEM

#30800 #30530
Plastic Throttle Plastic Throttle * Snap On.
kit Ball Joint
3X3mm 3X3mm
Set Screw 2mm Rod Set Screw

Throttle
Spring
3X3mm #10300
Set Screw Alum.Stopper
Fuel
Tube
#10300 ( 6mm )
Alum.Stopper
Plastic Collar * Align throttle servo same
as shown.
* Take the plastic collar
from brake system plastic
parts.

Brake

Idle Position

Note:
Battery life is short when using Alkaline batteries. For safety, we recommend using Full Throttle
Alkaline batteries for only 30 minutes before testing.. Battery strength affects braking
power and radio range. If voltage drops while running the car, you will loose control and
destroy your car! This is NOT covered under warranty.

To increase run time, upgrade receiver battery to a 5-cell hump pack. But, the most
important step you can make, “is to always use fully charged or fresh batteries when
running your car”. Another choice is to use OFNA #10196 2000 mAh NiMh AA batteries in
car and radio.

CHECKING ENGINE THROTTLE

* Align throttle servo same
as shown.
A B C
Brake (C)
1. Insert AA batteries into 1. Pull Full Throttle. 1. Push trigger to full
transmitter (8 Pcs). brake position.
2. Adjust alum. Stopper to
A
2.Turn on transmitter.
increase or decrease
3.Turn on receiver. the brake.
4.Center throttle trims as Idle Position (A)
shown .

Full Throttle (B)

IMPORTANT
CHECK RADIO THROTTLE
AND STEERING SWITCHES
• Full throttle arm position.
BEFORE RUNNING CAR
Spring rod pulls throttle
barrel open and brake
B
rods release pressure on
brake cams.
* Insert into transmitter.

C
B A C
• Full brake arm position.
Spring compresses
forward and brake rods
pull brake levers.
 ASSEMBLY OF THE DIFFERENTIAL GEAR
30779
4x4mm 4 x 10mm
Set Screw 40004 washer
40006 Diff. Gear
Cap Joint 30779 (Small)
40010 4 x 10mm
2.5x13.8mm washer 40004 30773
Diff. Gear 4mm
Pin
(Small) Cross pin

40003
Diff. Case

36053 30773
8x16mm 4mm
Ball bearing Cross pin 40004
40009 Diff. Gear
P6 O-Ring 40012 (Small)
6x15mm
Washer 40004 30779
Diff. Gear 4 x 10mm
(Builds one differential for Center)
30779 (Small) washer
40005
4 x 10mm
Break
4x4mm washer
Cap Joint
Set Screw Note: It is very important to add
or remove the #30779 washer if
40010 40004 the gear mesh is too tight or
2.5x13.8mm Diff. Gear too lose.
Pin (Large)

36053
8x16mm 40009
Ball bearing P6
O-Ring 40012
6x15mm * Apply diff. gear grease to the
OPTION: #49001 HD STEEL GEAR SET, Washer 40004 differential during assembly.
INSIDE DIFF. 40003 Diff. Gear * Fill the diff. the case to
Diff. Case (Large) approx 70% with grease.

ASSEMBLY OF THE DIFFERENTIAL CASE OPTION:

49032
43T Large
40010 Bevel Gear
2.5x13.8mm (must use 13t pinion)
Pin 40011
Diff. Gasket
( Builds two differentials for front and rear.) 40002
40002 41T Large
41T Large Bevel Gear
Bevel Gear
49032
40004 41T Large
Diff. Gear HD Bevel Gear
(Large)
36053
8x16mm
40012 Ball bearing
6x15mm
Washer
40009
*Use 6x15mm washer P6
40006
to adjust the gear mesh. O-Ring
Cap Joint

40010
2.5x13.8mm 3x12mm
Pin (Builds one differential for Center) Flat Head
Tapping Screw

40012 40001
6x15mm 47T
Washer Spur Gear 40011
Diff. Gasket 40001
47T
40004 Spur Gear
Diff. Gear
(Large)

*Use 6x15mm washer 36053

to adjust the gear mesh. 8x16mm
40009 Ball bearing
OPTION: P6
#49016 SPUR GEAR 50T O-Ring
40005
#49031 SPUR GEAR 50T, HD SPECIAL Break
Cap Joint 3x12mm
Flat Head
Tapping Screw
ASSEMBLY OF THE FRONT GEAR BOX
36053 OPTION: #49012 PINION GEAR
8X16mm 40017 13TOOTH
Ball bearing Gear Box

36053
8X16mm
Ball bearing

40021
14TSmall
36053 Bevel Gear
8X16mm
Ball bearing....4

40017
Gear Box
40024
13x16x0.2mm
Shim..............2

40024
13x16x0.2mm
Shim

Use shims to adjust gear

40021 mesh.
14T Small
Bevel Gear..............1

ASSEMBLY OF THE FRONT ARMS HOLDER

w t
94011 re en
Sc em
4x15mm C
Tapping Screw
(Small Head) 90026
5x5mm
Set Screw

36730
Cap Joint

94014
4x45mm
Tapping Screw
(Small Head)

MISC. SCREW BAG

40067

40015
4x15mm Front Lower arm
Tapping Screw........................2 40022 Holder (Rear/Plastic)
Front Lower Arm
Holder (Front)
90026
5x5mm 4x16mm
Set Screw......1 Flat Head
Tapping Screw

OPTION: #49002 CNC 7075

FRONT LOWER ARM HOLDER
40015
Front Upper arm
36730 Holder (Rear/Plastic)
Cap Joint................................1

4 x 16mm
Flat Head
Tapping Screw.......................4

94027
4x45mm 4x16mm
Tapping Screw........................2 Flat Head
Tapping Screw
ASSEMBLY OF THE FRONT SHOCK TOWER
OPTION: 49003
4mm CNC 7075 Alum. Shock Tower
Nylon Nut

40014
Front
Shock Tower

M4x15
TP Screw

94004
M3x12
TP Screw

ASSEMBLY OF THE FRONT KNUCKLE ARMS Assembly of the left and gight hand side
are the same.

36055
2.5x17mm
Pin

ent
w
Scre
Ce m
40105
8mm CVA Joint
40103 (Long/Front)
Front
Knuckle Arm 40103
Front
* "R" for right hand Knuckle Arm 90026
side. 5mm
Set Screw
L
36055 36054
2.5x17mm Alum.
Pin Wheel Hub 8mm
36053
36053 8x16x5mm
8x16x5mm Bal lbearing
Ball bearing

36053
S 36053 8x16x5mm
Cecre
mew
nt
8x16x5mm Bal lbearing
Bal lbearing 40105
36054 8mm CVA Joint
Alum. (Long/Front)
Wheel Hub 8mm
90026
5mm
Set Screw

ASSEMBLY OF THE FRONT LOWER ARMS Assembly of the left and gight hand side
are the same.
* A 4 x 10mm set screw is used
to adjust the ride height.
36870
4X10mm 40101
*Notice the direction
Set Screw 2mm Upper Arm
of the steering ball.
Ball End

*Notice the direction

40104 of the steering ball.
10mm
Steering Ball
4014 36870
10mm 4X10mm 40101
Steering Ball Set Screw Upper Arm
Ball End
40104
10mm
Steering Ball

40102
Front
Lower Arm
40102 40104
Front 10mm
Lower Arm Steering Ball
ASSEMBLY OF THE FRONT UPPER ARMS
(Right)
40101
Front
Upper Arm

(Left)
40101
36860 Front
5x40mm Upper Arm
Turnbuckle Ball End
10mm

0 10 20 30 40 50

mm

ASSEMBLY OF THE FRONT LOWER ARMS Assembly of the right and left hand side
are the same.
90020 36170
2.5mm Arm Shalf
E-Ring 3mmt

90021 90020
3mm 2.5mm
E-Ring E-Ring

40023
Lower Arm Shaft (4mm)

90021
3mm
E-Ring

ASSEMBLY OF THE FRONT SUSPENSION ARMS Assembly of the right and left hand side
Caster are the same.
Adjuster
* Insert the caster adjuster
into upper arm.
40104
4x16mm
Cap Screw

rew nt
Sceme
C

* Insert the drive shaft

into cap joint before assembly.

rew nt
Sceme
C

40104
4x16mm
Cap Screw
ASSEMBLY OF THE FRONT STABILIZER 94007
3x20mm
Screw

40029 30341
Stabilizer Stabilizer Ball
Ball End
(Long)

3x8mm 94007
40029 Set Screw 3x20mm
Stabilizer Screw
Ball End

30401 94033
6mm 3x3
Ball End Set Screw

94033
3x3
Set Screw

30341
A34B
Stabilizer Ball..........2

94007
3 x 20mm 40018
Screw ......................2 Stabilizer
Mount Plastic

94033 94019
3 x 3mm 3x10mm
Set Screw..............4 Flat Head
Tapping Screw

94019
3 x 10mm
Flat Head 40019
Tapping Screw........2 Stabilizer

94019
3x10mm 94033
94004 Flat Head 3x3
3 x 12mm Tapping Screw Set Screw
Tapping Screw..........1

94027
4 x 16mm
Flat Head
Tapping Screw..........4

40013
Front
Bumper
* Insert the front bumper
before assembly.

94004
3X12mm
Tapping Screw

40064
Chassis

4x16mm
Flat Head
Tapping Screw
ASSEMBLY OF THE WING STAY
( Take the plastic part from #40027Rear Win Stay Set. )

40027
49038 Wing Mount
Rear 40027
Shock Tower, Orange Wing Mount

40027
Rear
Body Mount 35313 *Insert the 3mm nylon nut
3mm before assembly.
Nylon Nut

94007
3x12mm 3x20
Tapping Screw 40027 Tapping Screw
Wing Stay
Post

40027
40027 Wing Stay
Wing Stay ( Right )
( Left )
40027
Wing Mount

3x20
Tapping Screw
40027
Wing Mount

OPTION: #49043 CNC ALIM.

POSTS, WING MOUNT, ORANGE

3 x 12mm
Tapping Screw........3

3mm
Nylon Nut........2

3 x 20mm
Tapping Screw............6

4 x 15mm
Tapping Screw
( Small Head )............2

94004
3x12mm
Tapping Screw
94011
4 x 15mm 4x15mm
Tapping Screw Tapping Screw
( Small Head )............4 ( Small Head )

OPTION: #49004 CNC 7075

REAR SHOCK TOWER

94011
4x15mm
Tapping Screw
( Small Head )
94012
4x20mm
Screw
( Small Head )
ASSEMBLY OF THE REAR GEAR BOX ONTO CHASSIS 36082
Assembly of the right and left hand side
are the same.
Rear
36053 Wheel Shaft
36055 8x16x5mm
36081 Ball bearing
2.5x17mm Rear
Pin Upper Right * A 4 x 10mm set screw is used
to adjust the ride height.
3 x10x3mm
Plastic Washer
4X10mm
36053 Set Screw
8x16x5mm
36054 Bal l bearing
8mm 3 x10x3mm 40102
Wheel Hub Plastic Washer Rear
Lower arm

90026
5mm
Set Screw

40102
90020 Rear
90020 2.5mm Lower arm
2.5mm E-Ring
5 x 5mm E-Ring
Set Screw............2
36170
3mm
90021 Arm Shaft
4 x 10 mm 3mm
Set Screw...........2 E-Ring

2.5mm
E-Ring..........4

3 mm
E-Ring..........4

40023
Lower Arm Shaft

3mm
90021
E-Ring

3mm
90021
E-Ring

3mm
90021
E-Ring

ASSEMBLY OF THE REAR UPPER ARMS 40065 40065

(Make two upper arms for left an right hand side. ) Upper Arm Upper Arm
Plastic Rod End 36850 Plastic Rod End
7mm Ball

36860
5x40mm
Turnbuckle

40065
Upper Arm 36860
Plastic Rod End 5x40mm
Turnbuckle

40065
Upper Arm
Plastic Rod End
16mm
36850
7mm Ball
36850
7mm Ball
ASSEMBLY OF THE REAR AND ANTI-ROLL BAR Assembly of the right and left hand side
35313 are the same.
3mm
Nylon Nut

Rear Upper Arm

Assembly
30341
Stabilizer Ball..........2

3 x 25mm
94007 Cap Screw
3 x 20mm
Screw ......................2

94033 35313
3 x 3mm 3mm
Set Screw..............2 Nylon Nut

94035
3 x 8mm 94007
et Screw..........2. 3 x 20mm
* Insert rear driver shaft Cap Screw
before assembly.

94020
3 x 12mm 40107
Tapping Screw..........1 Rear
Driver Shaft
(101mm)

40166 30341
Stabilizer Ball 94007
Stabilizer
3x20mm
Ball End
Screw
(Long)

3x8mm
40029 Set Screw
Stabilizer
Ball End

30401
6mm
Ball End

94033
94007 3x3
3x20mm Set Screw
Screw

94033
94007 3x3
3 x 20mm Set Screw
Cap Screw..........2

35313
M3
Nylon Nut..........2

94019
90018 3X10mm
3 X 25mm Flat Head
Cap Screw.........2 Screw
94033
3 x 3mm
Set Screw..........2 40018
Stabilizer
Mount Plastic
40019
94019 Stabilizer 94019
3 x 10mm 3X10mm 94033
Flat Head Flat Head 3x3
Tapping Screw........2 Screw Set Screw
 94027
4 x 16mm
Flat Head
Tapping Screw..........4

40064
Chassis

94027
4 x 16mm
Flat Head
Tapping Screw

ASSEMBLY OF THE SERVO SAVER

40037
Steering Plate
Hex Screw
40037 Option:
Steering Plate 40073
Hex Screw 4x8mm
Ball bearing
4x8mm flange
Plastic flange
40035 Bushing
35313 Servo Saver
M3 Nut..........1 Alum. Axle
Tube

4x10mm 40031
Servo Saver 6x10mm
Screw..........2
Horn A 40095 Plastic
Servo Saver Bushing
Connecting Plate,
Orange
40037
Steering Plat Servo Saver
Hex Screw....... 2 40031 Horn C
Servo Saver
Horn B
M3 Nut
Option:
* Put the 3mm
OPTION: #49014 CNC BALL nut before assembly.
6x10mm 40074
BEARING AXLE TUBE Plastic 6x10mm
Bushing Ball bearing

40033
Servo Saver 40036
40034
Spring servo Saver 40036
Servo Saver
Post Servo Saver
Spring Tension
40074 Post
Adjuster
6x10mm
Ball bearing

* Take the 4x8mm Plastic Flange bushing

and Plastic Bushing from servo saver plastic
parts tree
ASSEMBLY OF THE SERVO SAVER ONTO THE CHASSIS 4x15mm
Tapping Screw
4x10mm
Screw
40027
Front Body
Post

94009 * Assembly the front body post

4x10mm 40030 before assembly the Front Plate.
Screw..........2 Front Plate

94004
3 x 12mm
Tapping Screw..........1
3x12mm
Screw

94011
4 x 15mm
Tapping Screw
( Small Head )............2

94026
4 x 10mm
Flat Head Screw..........2

OPTION:
49005
CNC 7075 Alum. Front Plate
4x10mm 49019
Flat Head Graphite Front Plate
Screw

ASSEMBLY OF THE FRONT STEERING ROD 36850 36850

* Made two steering rods for left and right hand side. 7mm Ball 7mm Ball

40018
40018 4x56mm
35313 4x56mm Turnbuckle
M3 36850 Turnbuckle 36700
36700
Nylon Nut..........2 7mm Ball Steering
Steering
Ball End
Ball End
36700
40039 Steering 35313
Alum. Tapper Ball End 3mm
Washer................4 Nylon Nut

94021 40039
3 x 15mm 3mm Tapper
Flat Head Washer(Alum.)
Screw..........4

3x15mm
Flat Head
Screw
3x15mm
Flat Head
Screw

40039
3mm Tapper
Washer(Alum.)

* Anticlockwise mark.

Assembly of the right and left hand side

are the same.

0 10 20 30 40 50
35.5mm
mm
ASSEMBLY OF THE BRAKE AND SPLIT CENTER DIFF. MOUNT
* Make brake pads for each side. * Take off the double sided paper
before assembly.

36660
Brake Pad

36661
Brake Pad
linings

40045
Brake Pad 40040
Adjustment Screw Center Diff.
40044 Mount 40044
Brake Pad Brake Pad
Spring Spring

40044
40040 Brake Pad
40044
Center Diff. Spring
Brake Pad
Mount
Spring

40045
OPTION: #49030 CNC 7075 SPLIT Brake Pad
Adjustment Screw
CENTER DIFF MOUNT.
Assembly the brake disc holder
in the direction shown.

40040
Center Diff.
40040 Mount
Small Large
Hole
Center Diff.
Hole Mount

Small hole to the

Outside.

*Towards
40040 the front.
Brake Disk 40040
Holder 40040 Brake Disc
Break Disc Holder
Holder *Towards
the Rear.

40045
Brake Pad Screw...........4

40044
Brake Pad
Spring.........8

40043
Center Diff. Mount
40043 Post
Center Diff. Mount
Post...........................4
ASSEMBLY OF THE CENTER DIFF. INTO CENTER DIFF. MOUNT
Center Diff. Assembly

40042
Brake Disk 40042
Brake Disk

40042 40042
Brake Disk Brake Disk

OPTION: #49008 GRAPHITE

BRAKE DISKS, 2PCS.

94003
3x10mm
Screw..........4

94033
3 x 3mm
Set Screw..............2

30171
Brake Lever..........2

3x10mm
Screw

Scre
w
Cem
ent 40096
Center Diff.
Plate, Orange

Option
30212
5X8mm
Ball Bearing
3x3mm
Set Screw 3x10mm
Screw
30211
Plastic 30171 40031
Bushing Brake Lever Fuel Overflow
30171 3x3mm Proof Plate
Brake Lever Set Screw
30213 Scre
Cem w
Brake Cam ent

Put the front brake lever as

Shown.

OPTION: #49018 GRAPHITE

TOP CENTER PLATE
ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS
40028
Center Drive
Shaft (93mm)

40028
Center Drive
Shaft (93mm)

94026 4x12mm
4 x 12mm Flat Head
Flat Head Screw..........2 Screw

ASSEMBLY OF THE CENTER STIFFENER

ONTO CHASSIS
OPTION:
49015
CNC Alum. Chassis Brace Set
40018
Center Chassis
Brace
( Rear )

3x25mm
Cap Screw 40018
Center Chassis
3mm Brace
Nylon Nut ( Front )

3x12mm
Screw

94004
3 x 12mm
Tapping Screw........3
35313
3mm
Nylon Nut........1
2.6x10mm
Flat Head
4x16mm Tapping Screw
Flat Head
90019 Tapping Screw
3 X 25mm
Cap Screw.........1
4x16mm
Flat Head
94027 Tapping Screw
4 x 16mm 4x16mm
Flat Head Flat Head
Tapping Screw..........4 Tapping Screw
ASSEMBLY OF THE STONE GUIDE Assembly of the right and left hand side
are the same.

OPTION:
Stone Guard
Yellow . 40078
Red . 40079
Lime . 40080
Blue . 40081
Black . 40046

40046
Stone Guard

3x10mm
Screw

3x10mm
Screw

40046
Stone Guard

3 x 10mm 3x10mm
Tapping Screw..........6 Screw

ASSEMBLY OF THE RECEIVER BOX

40047
2x10mm Receiver Box
Tapping Screw Cover
* Use the screw provided
with your radio

40898
2x25mm
40047 Screw
Receiver Box

*Use the original battery

case or rechargeable
hump pack battery.

Battery Case,
Provided by
Radio
10280 3x10mm
Switch Cover Screw

Switch, Provided by Radio

40047
Receiver Box 30560
2 x10mm Antenna
Tapping Screw..........2 Pipe

* You must add padding for radio

and battery once lid is closed.
2 x 25mm Screw.....1 Do not let radio and/or battery be
loose in box.
Receiver
Option:
94003 10212
3 x 10mm Hump Pack
Tapping Screw..........1 Battery
ASSEMBLY OF THE RADIO TRAY 3x10
Tapping Screw

3x10mm
Tapping Screw
3x10
3x10mm Tapping Screw
Tapping Screw
49039
Alum.
Radio Tray, Orange Throttle
Servo

Steering
Servo

3x12mm
40027 Tapping Screw
Radio Tray 40027
Post Radio Tray
( Plastic ) Post
( Plastic )
OPTION: 10274
49044 CNC ALUM. POST, Servo Post
RADIO TRAY, ORANGE

Servo Post

* Take the servo post

from servo saver plastic
part tree.

94003
3 x 10mm
Tapping Screw..........14

*Connect as per radio.

94019
3 x 10mm
Flat Head
Tapping Screw.........8 OPTION:
49017 GRAPHITE RADIO
TRAY.

3X10mm
Tapping Screw

40031
Transponder
Holder
3x10mm
Flat Head
Tapping Screw
* Use 4 pcs for
receiver box.

3x10mm
Flat Head
Tapping Screw
* Use 4 pcs for
radio tray.
 ASSEMBLY OF THE CLUTCH INTO ENGINE
Notes:
3 x 5mm Screw
Non-Pull Start Engines...
• Alum. Washer behind the flywheel is not needed when using Force engines or similar types. O.S. Engines will
require washer spacer.

3 X 8mm • To check!..place the brass corn against the engine bearing, then flywheel. You should be covering one or two
Washer thread of the engine shaft. If this is the case, you do not need an additional washer behind the flywheel.

You must cut the engine shaft if too long. Count 6 threads in front of the flywheel and mark. This is all you need to
tighten the clutch nut and mount the flywheel. 30481
30481 3 x 20mm
3 x 20mm 3 x 20mm Hex Screw
Force Pull Start Engine w/threaded shalf...
Cap Screw Hex Screw
• Force Pull Start Engines required NO spacer and no shaft cutting. The engines comes with an alum cast driver
washer, you use this part as the spacer, not the alum. washer shown. Also, use the special flywheel brass corn.
3mm Nylon This corn fits the thread shaft diameter so you can tighten the flywheel against the drive hub.
Locknut

#10010
#10398 - 12T Clutch Shoes
#10399 - 13T Black Type
#10400 - 14T (stock) #10102
#10401 - 15T Clutch Spring
#10402 - 16T #10330
#10403 - 17T 30481
Brass, Corn
#10404 - 18T (large hole) Note 3 x 20mm
Clutch Bells Hex Screw
SG Shaft
#34110
5x10x4mm #10098
Ball Bearing SG Nut
#34110
5x10x4mm & Shim KiT
Ball Bearing
Threaded
#10329 Shaft
Brass, Corn
(sml hole)
SEE NOTES
ABOVE
#10040 (stock) #10048
3 Pin OR 10049
#10091 Flywheel, Taper
3 x 8mm #10043
Clutch Nut
Washer 3 Pin
screw type #30480
Misc. Hardware * Shoes are Flywheel, Fan
3 x 5mm #10099 trailing. Engine Mount
Screw

Options
Option
10799
Clutch Spring
* Fit the flywheel using a cross Flywheel Wrench
wrench or deep socket. 10100 - Springs, Polished, Med.
* Place the clutch shoes 10101 - Spring, Gray, Hard
with the clutch springs
If engine turns when tightening,
hold piston with large thick tie-wraps over the 3 pins of the 10102 - Spring, Black, Stock
and hard wood in exhaust port. flywheel.
Do not use metal, it will Using a screw driver as a lever,
bend the small end of the
Clutch Shoes, 3 shoe clutch
damage engine.
clutch spring behind the 10010 - Shoes, Carbon Material, Black
clutch nut and press 10011 - Shoes, Alum. CNC Blue, Lite Weight
down to snap shoe in
place. 10012 - Shoe, Alum. CNC Purple, Med. Weight

#10021 - Black
ASSEMBLY OF THE AIR FILTER #10027 - Yellow
#10028 - Pink
#10029 - Blue
You must oil foam filter before use. Nylon Strap Air Filter Connector
Filter will not work if not oiled. ( Small ) Nylon Strap
( Small )

Clean with soap and water only.

You will damage foam if washed
if fuel!

#10016
Air Filter
Sponge
Refills

#10017 - Blue
#10018 - Yellow
#10019 - Rose
#10034 - Chrome
Foam Air filters Unit

#10013 - Mount Wire

3 x 10mm
Tapping Screw
INSTALLATION OF THE FUEL TANK
AND ENGINE ONTO CHASSIS Note Book Paper

40066 3X15mm
40066
Pressure Tapping Screw
Fuel Nipple
Nipple
40109
Fuel Tank, 140+cc
* Assemble the fuel tank post
before assembling the fuel
nipple.
3X15mm
Tapping Screw

* Use note book paper to set

gear backlash between spur gear
and clutch bell.
If the space is not correct the spur gear
will be damaged.

Spur Gear

90 Degree
Clutch Bell
3x20mm
Cap Screw

* Loose or tighten 3x20mm cap screw

and 5x10mm hex screw to align
38120 spur gear and clutch bell gear to 90
Fuel Tank degree.
Post

* Take the fuel tank post

from 40047 plastic parts tree.

10114
5mm Hex Screw
for Engine Mount

3x10mm
Tapping Screw
3x10mm
Tapping Screw

ASSEMBLY OF THE MANIFOLD AND #10069

Manifold Adapter
MUFFLER ( Red Silicone ) #31991
Manifold, Polished
* Read this page very carefully.

40051
Muffler
Wire
#10120
Manifold
3x3mm Spring
Set Screw

40050
Muffler Mounting
Post * Tighten the strip
and cut off the excess.

#10184 Option:
#10079 Blue, Silicone 10182
Tube
Alum. CNC
Pressure Nipple
Silicone Tube, Red
5x5mm or 4x4mm
10183
4x10mm * Drill a hole (Size 3.5mm)
Flat Head Set Screw in the place and align as shown. Silicone Tube, Yel.
Screw Use a two part epoxy glue to 10184
#31992 full seal the nipple base to the nipple.
Dual Chamber, Polished Silicone Tube, Blue
 35313
ASSEMBLY OF THE FRONT STEERING ROD 3mm
Nylon Nut

* Use the screw provided * Enlarge this hole.

with your servo.
30690
30410 3x30mm
6mm Tie Rod
3x10mm Tie Rod End
Screw
10768 30411
Servo Horn 6mm
Ball

30411
6mm
3x15mm Ball
Screw

30410
6mm
Tie Rod End

Parallel

16mm

0 10 20 30 40 50 * Align the steering servo as shown.

mm

ASSEMBLY OF THE BRAKE LINKAGE 2x8mm

2x4mm
#30800 2mm Rod Screw
Screw
Brake System Plastic Parts Set
2x6mm
* Cut the shaded
Washer
area as shown.
Servo
Mount

3x3mm
Set Screw
10768
3x25mm Servo Horn, Yel.
Screw
2mm Rod
Adjust * Cut the shaded area
Mount 2mm as shown.
36140 2x4mm Tie-Rod 2mm
2mm Screw End Nut
Adjust Mount
2x6mm
Washer

3x3mm
2mm set screw
3x10mm
Rod Screw

Plastic Collar
3x3mm
Set Screw
30530
Throttle
Ball End
10300
Throttle Alum.
10300 Throttle Stopper
Slider
Alum. Spring
Stopper
 ASSEMBLY OF THE BRAKE LINKAGE INTO 10300 3X3mm
BRAKE ROD Alum.
Stopper
Set Screw *Snap On.

5mm
Fuel
Tube

* Align throttle servo same

5mm
as shown.
Fuel
Tube

Brake

Idle
Position

Full Throttle

*use the screw USING BREAK ADJUST NUT

provided With your radio.
Tighten
Less Brake

Loosen
More Brake
Loosen Tighten

* Tighten or loose the adjuster nut

will change the brake.

ALIGN THROTTLE SERVO AND BRAKE SAME AS SHOWN

( Neutral Position )

Engine at idle

( Braking Position )

Brake is not on

Brake is on

Brake Adjust Nut

Less Brake ( Full Throttle Position )

More Brake
Engine at full throttle

Loose Tighten

* Tighten or loose the adjuster nut

will change the brake.

Brake is not on
SHOCK ASSEMBLY * Assembly 2 pieces of the
49041 shock shaft for front and
Oil Seal rear.
Spring
Adjuster,
Orange 40076 40060
32235 40059 Shock 2.5mm
Shock Piston.........4 14.7mm Cylinder Nylon Nut
O-Ring
Fit the O-ring into groove. 32237
3.5mm
O-Ring
32235
Make a PAIR for front Shock
40059
14.7mm O-Ring....4 Piston

32237 2.6 x 5mm

7mm R-Ring Washer
* Short shaft
for front.
32237
32237 2mm
1mm Washer.............4 32237 Washer 40054
1mm Short Shaft
Washer

32237
2mm Washer..........4
49041
Spring 40077
Adjuster, Shock
40056 Orange Cylinder
Shock Plastic
Rod End
J-47C
Spring Adjuster....4

Make a PAIR for rear

40060
2.5mm Nylon Nut........4 40056 * Long shaft
Shock Plastic for rear.
Rod End
40055
Short Shaft
APPLY OIL TO SHOCK BODY
BEFORE INSTALLING COLLAR

* Be careful not to damage shock shaft.

FILLING THE SHOCKS WITH OIL

2. Pull down piston, attach pressure top 4. Assembly the dust cover.
1. Pull down piston and pour oil into and shock oil overflow with tissue
shock cylinder. Remove air bubbles paper.
by slowly moving piston up and down. 3. Tighten up shock cap.

OIL
40093
Shock Cap
Hard Coated

*Leave 3mm.

40058
Shock Shaft
Dust Cover
UP

32033
down. Pressure Top

*Move Slowly. * Fit into the groove.

* Cut 6mm for front.

ASSEMBLY OF THE SPRING OPTION:

40063 40063 - CNC Alum Spring Holder, Orange
Spring Holder
OPTION: 40069
40069 - Black, Stock, Spring Set Black
40070 - Green, Soft Set Shock Spring
40071 - Blue, Med. Set 30411
40072 - White, Hard Set 6mm Ball

40052 - Front Shock Set

40053 - Rear Shock Set
* Push 6mm ball joint
into ball end.
 ASSEMBLY OF THE FRONT SHOCK ABSORBER Assembly of the right and left hand side
are the same.
3x25mm
Cap Screw

30702
3 x 20mm
* Take the plastic bushing Cap Screw..........2
from the shock plastic
parts tree. 35313
M3
Nylon Nut..........2
36610
Shock Upper Fixing

Plastic
Bushing 90018
3 X 25mm
Cap Screw..........2

36610
Shock Support.....2
3mm
Nylon Nut

Assembly of the right and left hand side

are the same.

3 x 20mm
Cap Screw

3x25mm
Cap Screw

ASSEMBLY OF THE REAR SHOCK ABSORBER

36610
Shock Upper Fixing

Plastic
Bushing

3mm
Nylon Nut

3 x 20mm
Cap Screw

ASSEMBLY OF THE TIRES AND WHEELS

86035
wheel

86062
X Equal Pin
Tire

INSTANT
GLUE

* Apply instant glue into

the groove of the wheel.
81095
Inner Sponge
ASSEMBLY OF THE WHEELS ONTO
FRONT KNUCKLE ARM AND REAR HUB

Assembly of the right and left hand side

are the same.

30051
Wheel Nut
86044 - Red
86045 - White
86046 - Lime
86047 - Yellow
86048 - Black
86049 - Chrome
17mm Dual Spoke,
30051 2 pairs (4 wheels) per Bag.
Wheel Nut

ASSEMBLY OF THE WING 3x12mm

40083 - Wing White Screw OPTION:
40084 - Wing Yellow 49045
40085 - Wing Red CNC Alum. Wing Washer
40086 - Wing Lime Orange, 2 pcs.
* Drill two 7mm holes 40027
for mounting. 40087 - Wing White Countersunk
Plastic Washer
25mm
25mm

40084
Wing, Yellow

*Upper Deck Of
The Wing.

0
25 20 15 10 5 5 10 15 20 25

* Check the hole spacing on the underside.

MOUNTING THE BODY
31149
Body Clips

31149
Body Clips

FOR A STICK PACK BATTERY

3x12mm
Screw
* Use tape to secure the battery.
3x12mm
Tape Screw
40048
Stick Pack
Battery Holder 40048
(5 Cell) Battery Holder
Mount
3x12mm
Stick Pack
Screw
Battery(5 Cell)
( Not Included.)

3x12mm
Screw

* Insert battery wire into

receiver and connect to
the switch.

40048
Battery Holder
Mount

CHANGING WIDTH FROM 330mm TO ROAR LEGAL 310mm

Adjustable width, lower arms.

310mm Simply cut outside 330mm pin
holes.
330mm
Leave as much plastic as possible
SET-UP GUIDE

RIDE HEIGHT ADJUSTMENT

2mm
Hex Screw

Use a 2mm hex screw to adjust the ride height.

Screwing in the 4x10mm set screw....Ride height becomes lower.
Uncsrewing the 4x10mm set screw..Ride height becomes higher.

Soft Firm
3
12

12
Soft Firm
ENGINE BREAK-IN AND TUNNING
(BREAK-IN THE ENGINE BEFORE DRIVING THE CAR!)

• Choose a wide clear outdoor location with low dirt and dust. OPTIONAL OFNA CAR STANDS
• Set the car on box or holder with wheels off the ground.
• Turn on radio and car. Make sure throttle is at idle position.
• Fill fuel tank and set master engine needle.
• Prime fuel line and Heat glow plug before pull starting engine.
• When started, let engine fast idle for two tanks of fuel.

WOOD BLOCK

STARTING OF THE ENGINE * To start the engine, use hand held starter
motor or starter box.
How to start the engine: Rubber wheel turns engine
1. Turn on transmitter and then receiver. flywheel.
2. Fill fuel tank with fuel bottle.
3. Connect 1.2V glow plug starter.
4. Start engine with 12V starter or starter box
( Note the direction of the starter.)
5. After the engine be started, remove the
1.2V glow plug starter.
#10250
Starter Box
* Follow the engine manufacturer instruction manuals
regarding engine set-up, carburetor and maintenance.
12V Starter

1.2V
Glow Plug
Starter

* Note the direction of the

starter.

Connect with 12V battery

TUNING AFTER BREAK-IN
Close master needle by turning clockwise until it stops.
Then open needle by turning counterclockwise 3 turns
(rich setting). When running car, adjust carb with 1/8 clockwise turns,
slowly leaner, until the top speed good. Check engine
temp, if possible, for no more 250 degrees.

Adjust low end needle for best throttle response. Use only
small turns. From idle, give it full throttle, if throttle is slow
lean out needle until good.
Adjust barrel stop so it will not close, accept for a small gap.
This gap will be the idle setting. You will notice the idle will
increase with a wide gap.

Idle adjuster screw &

Barrel Stop

Lean Rich
APPENDIX PAGES
SHAFT START
NOTICE:

SOME VIOLATOR RTR KITS WILL COME WITH “SHAFT START”

(same as Rotor Start). THEREFORE, A PULL START ENGINE IS NOT
USED AND THE SHAFT START BACK PLATE IS ALREADY
INSTALLED.

BEFORE YOU CAN USE THE SHAFT START MOTOR HANDLE, YOU
MUST FIRST GET OR BUY A STANDARD 7.2 BATTERY PACK.

AFTER POWERING UP THE MOTOR HANDLE, INSERT THE SPECIAL

DOG BONE SHAFT AND TURN OVER THE ENGINE.

CHECK BEFORE STARTING:

1) IS THE FUEL LINE PRIMED?

2) IS THE CARBURETOR SET FOR BREAK-IN SETTINGS?

3) IS THE RADIO ON AND THROTTLE AND BRAKE LINKAGE

CHECKED AND OKAY TO START?

4) MAKE SURE RADIO AND CAR RECEIVER BATTERY ARE ON AND

WORKING WITH GOOD POWER.

5) PLACE THE GLOW HEATER ON PLUG.

6) HOLD THE CAR AND STARTUP THE ENGINE, BY PUMPING

THROTTLE SLIGHTLY. DO NOT HIGH REV ENGINE WHEN IT
STARTS, AT THIS TIME!