The Euclid Chemical Company
CONCRETE STAIN SEALER WB
Water-Based Acrylic Concrete Stain and Sealer
Description
CONCRETE STAIN SEALER WB is an acrylic latex sealer designed to beautify, protect and seal concrete and
masonry surfaces. CONCRETE STAIN SEALER WB is a blend of acrylic resins and the finest pigments available,
Stains
providing durability and excellent color fastness. CONCRETE STAIN SEALER WB will seal and restore dull-
looking concrete to a new luster while providing an easy-to-clean surface. CONCRETE STAIN SEALER WB
comes in a wide selection of colors for all environments
Primary Applications
• All unpainted masonry and concrete • Architectural concrete
• Pool decks • Precast concrete
• Driveways and sidewalks, patios • Spray-Deck
Technical Information
Typical Engineering Data
The following results were developed under laboratory conditions.
Drying time* at 73 °F (27.2 °C), 50% RH:...1 to 2 hours Foot traffic.................................................24 hours
CONCRETE STAIN SEALER WB
Wheel traffic................................................... 48 hours VOC content.............................................<100 g/L
Adhesion to concrete......................................excellent Solids content..........................................42 to 48%
Min. Working Temperature……..............55 °F (12.8 °C) Resistance to yellowing from UV light …..excellent
*Low concrete or air temperature and/or high relative humidity will extend drying time.
Packaging
CONCRETE STAIN SEALER VOC is available in 1 gal (3.8 L) and 5 gal (18.9 L) units
(For color selection, refer to Increte Standard Color Chart).
Shelf Life
2 Years in original, unopened container.
Coverage Master Format #:
150 to 200 ft²/gal (3.67 to 4.90 m²/L) per coat. For best results, two thin coats of sealer are recommended.
00 00 00
1611 Gunn Highway • Odessa, FL 33556
www.increte.com
800-752-4626 t • 813-920-1516 f
Directions for Use
APPLICATION PROCESS
Application on a test area is highly recommended when unfamiliar with surface and/or product. This extra
step will determine if the surface is properly prepared, the probable coverage, and the best method suited for
application.
Preparation: Concrete should be at least 28 days old. All paint, oil, and grease must be removed. Old paints or
coatings can be removed mechanically or chemically using UNI STRIP. Oil, grease, and dirt must be removed
using GREASE A WAY, rinsed or pressure-washed thoroughly, and the surface allowed to dry completely.
Concrete must be etched, because a profiled surface is required. Etching should be done with 5 parts water to 1
part muriatic acid solution. Extremely hard or polished concrete may require a second application with stronger
solution. Rinse surface thoroughly with plenty of clean water and let dry completely. Ambient and substrate
temperature must be between 55 to 90 °F (10 to 32 °C). Avoid application during rainy, foggy, or very humid
weather when water condensation forms on the surface.
Mixing: Always stir stain well before use and during application to prevent settling and to ensure proper dispersion
of colorant. A variable-speed drill and a paddle mixer is the preferred method for this step.
Roller Application: Roll on first coat using a 1/4 in (6 mm) nap, lint-free roller. Apply using uniform, even strokes
in the same direction. A second coat must be applied after the first coat has completely dried, usually a minimum
of 4-6 hours.
Spray Application: Product may be sprayed using an airless sprayer with a medium tip size and very low
pressure. For a uniform coverage, especially over decorative concrete, it is recommended to back roll the
product after spraying. If conditions are windy or extremely hot, adjust technique to avoid “dry spraying” the
surface. A second coat must be sprayed only after the first coat is dry.
Clean-Up
Use soap and warm water for cleaning tools/equipment immediately after use.
Precautions/Limitations
• Do not allow product to freeze. Store between 50 and 90 °F (10 to 32 °C).
• Excessive build-up of CONCRETE STAIN SEALER WB or puddling of the product during application can lead
to and discoloration.
• Do not apply when concrete surfaces or ambient temperatures are below 50 °F (10 °C) or if rain is expected
within 12 hours after application.
• Not resistant to gasoline or other automotive fluids.
• Do not thin this product.
• For professional use only.
• In all cases, consult the Safety Data Sheet before use.
Rev. 08.15
WARRANTY: The Euclid Chemical Company (“Euclid”) solely and expressly warrants that its products shall be free from defects in materials and workmanship for one (1) year from the date of purchase. Unless authorized
in writing by an officer of Euclid, no other representations or statements made by Euclid or its representatives, in writing or orally, shall alter this warranty. EUCLID MAKES NO WARRANTIES, IMPLIED OR OTHERWISE,
AS TO THE MERCHANTABILITY OR FITNESS FOR ORDINARY OR PARTICULAR PURPOSES OF ITS PRODUCTS AND EXCLUDES THE SAME. If any Euclid product fails to conform with this warranty, Euclid will replace the
product at no cost to Buyer. Replacement of any product shall be the sole and exclusive remedy available and buyer shall have no claim for incidental or consequential damages. Any warranty claim must be made within
one (1) year from the date of the claimed breach. Euclid does not authorize anyone on its behalf to make any written or oral statements which in any way alter Euclid’s installation information or instructions in its product
literature or on its packaging labels. Any installation of Euclid products which fails to conform with such installation information or instructions shall void this warranty. Product demonstrations, if any, are done for illustrative
purposes only and do not constitute a warranty or warranty alteration of any kind. Buyer shall be solely responsible for determining the suitability of Euclid’s products for the Buyer’s intended purposes.
