Super Color Stain

Roller, spray or brush applied, WHERE TO USE

water based opaque acrylic Enhance appearance and protect concrete,
stain. CMU, stucco, brick, and as a washable
finish for Elastideck.

Performance Characteristics Surface Preparation Application

Water repellent n Remove loose and deteriorated n Apply a test sample to determine
n 2 coat application passes material, laitance, dirt, dust, oil adhesion. Test using ASTM D335
ASTM E514. and any surface contaminants cross-hatch adhesion test.
Breathability that will inhibit proper adhesion. n Substrate temperature must
n Water vapor permeable. n Prepare surface to be be above 45°F.
Suitable for on-grade applications. sandpaper-like texture (CSP 3) n Ambient temperature must
Alkaline stable by mechanical abrasion or be above 45°F for the entire
n Formulated for water blasting. Refer to ICRI curing period.
highly alkaline substrates. Surface Preparation Guide 03732 n For roller applications use a
Durable for information about 3/8 - 1/2 inch synthetic nap roller
n UV stable. Concrete Surface Profile (CSP). depending on texture of
Mildew resistant. n Surface must be dry and frost free. substrate.
Colorfast n Repair large voids and damaged n For spray applications use an
n Premium quality, exterior grade areas with Conpro Set. airless sprayer with a
pigments minimize fading. n For cracks greater than 1/16 inch 0.019 - 0.021 tip.
Extensive color spectrum rout and caulk with a urethane n Work to pre-determined
n 38 standard colors and sealant. Refer to SWRI Sealants – break points in the structure.
custom matching. The Professionals’ Guide. n Maintain a wet edge.
Low maintenance n A second coat may be applied
n Excellent dirt and stain resistance. Priming when the first is dry-to-touch.
n Priming is not necessary under For horizontal applications
normal circumstances. n First apply Elastideck to the
substrate. Next, apply Super
Mixing Color Stain in the same color to
n Stir or mechanically mix using provide a durable pedestrian wear
a low speed drill (400 - 600) surface. Refer to Elastideck data
until homogenous. bulletin for more information.
n Mix pails from different batches
when an entire surface is visible. Curing
n Protect from moisture for 24
hours.

Clean Up
n Clean tools and equipment with
water immediately after use.
Clean adjacent areas with water
before material dries.

DIVISION 9 SUPER COLOR STAIN

 Super Color Stain
Coverage/Yield Limitations First Aid
n 250 ft.2/gal. @ 6 mils wet. n A light color stain may not completely n In case of skin contact, wash
n 150 ft.2/gal. @ 6 mils wet for split block hide a dark substrate, even with 2 coats. thoroughly with soap and water.
or rough surfaces. n Do not apply if precipitation is forecast n For eye contact, flush immediately
within 24 hours of application. with a high volume of water for at
Product Handling n Do not apply in strong winds. least 15 minutes and contact a
Packaging n Do not apply to frozen surfaces. medical professional.
n 5-gallon containers. n Do not apply if temperature n For respiratory problems, remove
Shelf Life of substrate is below 45°F. person to fresh air.
n 18 months in unopened containers. n Do not apply if ambient n If respiratory difficulty persists,
Storage temperature is below 45°F. contact a medical professional.
n Protect from freezing.
n Transport and store in cool, clean, dry Health and Safety Disposal
conditions in unopened containers. n Product is slightly alkaline. n Dispose of material
n High temperature will reduce shelf life. n Do not ingest. in accordance with local,
n Avoid contact with skin and eyes. state and federal regulations.
n Avoid breathing vapors.
n Refer to Safety Data Sheet (SDS) for
additional information.

Technical Data
Physical state and appearance Liquid emulsion – thin – paint-like
Base Aqueous
Polymer 100% Acrylic
pH 8.7
Percent solids by weight 35%
Percent solids by volume 31%
Viscosity ASTM D562 81 KU – paint paddle
Volatile organic content – VOC ASTM D3960 Less than 0.32 lbs./gal. – 38 gms./liter
Density of liquid coatings ASTM D1475 9.64 lbs./gal.
Drying time 2 hours @ 65oF – dry to touch
Water vapor transmission ASTM D1653 wet cup 12 perms – 1 coat @ 5 mils.
Fungus resistance Fed. Spec. TT-P-19D Pass – no growth
Accelerated weathering – QUV ASTM G154 2000 hours –
UV-B cycled with condensation – no effect
Resistance to chemicals ASTM C1308 Dried ketchup/Dried coffee/Dried soda – excellent
Gas/Motor oil - excellent
Wind driven rain Fed. Spec TT-C-555B No leakage @ 62 mph – 2 coats
Water penetration and leakage ASTM E514 100% reduction – 2 coats
Resistance to abrasion – tabor ASTM C1353 250 cycles – 2.8% loss – H22 wheel with 500 gms.
Freeze/thaw stability ASTM C932 Pass
Heat stability ASTM C932 Pass – 2 weeks @ 120oF
Dirt pick-up ASTM D3719 Excellent
Mud cracking @ 15 mils. None

FOR PROFESSIONAL USE ONLY

Conproco warrants this product for one year from the date of manufacture to be free from manufacturing defects and to meet the technical properties on the current
technical data sheet if used as directed within shelf life. User determines suitability of product for use and assumes all risks. Buyer's sole remedy shall be limited to the
purchase price or replacement of product, exclusive of labor or cost of labor. July 29, 2020.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED SHALL APPLY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
CONPROCO CORP SHALL NOT BE LIABLE UPON ANY LEGAL THEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES.

TELEPHONE 800.258.3500 • FAX 603.743.5744 • WEB ADDRESS www.conproco.com