APS901Z

Remote Start
System Layout

Replacement Part #4180070

Important Update Replacement Part #181BP 6
6 Empty Empty
The default Data Port Protocol of this system is ADS. If using 5
an FLCAN or other external integration module be sure to 5 Blue LED (-)
choose iDatalink 2-Way when flashing.

Antenna
4 4 Red Valet Switch
This system will also support DBI. This will require 3 3 Black Ground (-)
programming Feature Bank 2, Feature 18 to DBI. 2 2 Green Data RX

VOXX
1 1 Pink BaƩery 12V (+)
Replacement Part #4120465

4
4 Red BaƩery 12V (+)
3

CarLink
3 Blue Data TX
2 2 Black Ground (-)
1 1 White Data RX
Accessory Sold Seperatly
1 3 5
4
2 4 6 4 Red BaƩery 12V (+)
3 3 Blue Data TX

DBI
1 Yellow Starter Output (+) 2 2 Black Ground (-)
2 Green IgniƟon 2 Output (+) 1 White Data RX
6 Pin RS Harness

P 1
3 Red BaƩery 12V Input (+) Accessory Sold Seperatly
4 Red/White BaƩery 12V Input (+)
5 Purple Accessory Output (+) P 14 Green/Orange Tach Input
6 Blue IgniƟon Input / Output (+) 13 Black/Yellow Pulse During Crank Output (-)
Replacement Part #4120467 12 Green/Yellow Glow Plug Input (+)
11 Black/Red Pulse AŌer Shutdown Output (-)
1 White Parking Light (30) Output

14 Pin Main Input/Output

P
13 14 10 Empty Empty
4 Pin Light

2 White/Red Parking Light (87) Input 11 12 9 Black/Blue Factory Disarm Output (-)
3 Yellow/Black Ignition Output For Alarm (+) 9 10
8 Brown/Black Brake Input (+)
4 Black Ground Input (-) 7 8
7 Black/Lt. Green Factory Arm Output (-)
5 6
Replacement Part #4120463 6 Dk. Blue/Black
3 4 External AcƟvaƟon Input (-)
1 3 1 2 5 Lt. Blue Remote Start Status Output (-)
2 4 Replacement Part #4360841 4 Green Unlock Output (-)
3 Gray/Black Hood Input (-)
2 Empty Empty
1 Black/White Horn Output (-)
Replacement Part #4120466

For Complete Installation Guide and Technical Support Visit www.voxxuniversity.com. Or Call 1-800-225-6074 2020 Voxx Electronics. All Rights Reserved.
 The Feature Banks below can also be programmed using the FlashLogic Weblink.
Tach Programming Please visit www.FlashLogic.com for more detail.
Op�ons
The installer must manually configure the Engine Confirmation method in Feature Bank Feature Bank 2 1 Chirp 2 Chirp 3 Chirp 4 Chirp 5 Chirp 6 Chirp
3, Feature 5. The default method is “Tach”. When using the default “Tach” method, the
vehicle tach rate must be programmed. To enter tach rate programming: 1 Lock / Unlock Func�on 500ms 3.5sec 500ms L, DBL UL DBL L, 500ms UL DBL L, DBL UL 500ms L, 350ms UL
2 Accessory Lock NA
1. Turn the ignition key ON.
3 Accessory Unlock NA
2. Press and release the valet button three (3) times.
3. Turn the ignition key OFF. 4 Exterior Illumina�on NA
4. Press and hold the valet button. 5 Auto Relock NA
5. While holding the valet button, start the engine using the key. 6 Auto Arming NA
6. Hold the valet button for approximately ten (10) seconds. If connected to the vehicle 7 No�fica�on Sound NA
Tach source, the system will flash the parking lights one (1) time every second. 8 Horn Timing 16ms 30ms 40ms 50ms 10ms

APS901Z
7. Release the valet button. The system will turn on the parking lights for two (2)

Features
9 Valet Override Method NA
seconds to indicate the tach rate is programmed.
10 Driver Priority Unlock NA
The tach rate can also be programmed without the use of a valet button. This is helpful 11 Silent Choice NA
Remote Start when using the OEM remote or CarLink system to control this module. To program the tach 12 Park Light / Trunk Swap NA

Quick Installation Guide

rate without a valet button: 13 AUX Ch. 4 NA
14 AUX Ch. 5 NA
1. Turn the ignition key to the ON position and start the vehicle’s engine.
15 AUX Ch. 6 NA
2. Wait for the engine RPM to lower to a normal idle.
3. Press and hold the vehicle’s brake pedal. 16 AUX Ch. 7 NA
For Complete Installation Guide and Technical Support Visit 4. Press the LOCK button on the OEM remote or the Carlink App. 17 Security Profile OFF OEM Security W/ OEM Remote Start OFF W/ Keyless
www.voxxuniversity.com 18 Data Port Protocol ADS DBI
Or Call 1-800-225-6074 Note: Programming tach signal via OEM or Telematics control is only available on Firmware
v1.47 or Higher. Op�ons
Feature Bank 3
Remote Programming
1 Chirp 2 Chirp 3 Chirp 4 chirp 5 Chirp 6 Chirp
1 Defrost Output NA
The APS901Z includes two (2) programmed remote controls. If required, additional remote
2 RS Start No�fica�on ON OFF
controls can be programmed to the system. Remote Programming is located in Feature 3 RS Run�me 15min 20min 45min 60min 5min 10min
Bank 1. To enter Remote Auto Programming: 4 RS Parking Lights Steady Flashing
5 Engine Confirma�on Tach Voltage Data Hybrid
1. Turn the ignition key to ON. 6 Voltage Level >0.5v B4 Start <0.5v B4 Start
REV. B 2020 Voxx Electronics. All Rights Reserved. 2. Press and release the valet button three (3) times. The system will beep and flash the
7 Igni�on 2 Output Ignition Accessory Start
parking lights one (1) time.

Notifications 3. Press the Start button on each remote. The system will beep one (1) times to indicate 8 Igni�on 3 Output N/A
the remote has been programmed. 9 Accessory Output Accessory Igni�on Start
10 Transmission NA
Remote Start
Feature Programming 11 Max Crank Time 0.8sec 1.0sec 1.5sec 2.0sec 3.0sec 4.0sec

Features
If the remote start fails to start the vehicle, the system will flash the vehicle parking
lights to indicate the cause. 12 Diesel Delay OFF Diesel 5 Diesel 10 Diesel 15 Diesel 20 Diesel 30
13 Temperature Start NA
1 Run�me Expired The APS901Z Feature Banks can be programmed by using the valet button and remote. To
14 Crank Dura�on Averaging Preset
enter Feature Bank programming:
2 Remote Shutdown 15 RS Shock Override NA
3 Brake On 1. Turn the ignition key to ON. 16 Turbo Timer NA
2. Press and release the valet button three (3) times. The system will beep and flash 17 Start Ac�va�on Two Press One Press Three Press
4 Manual Mode the parking lights one (1) time for Feature Bank 1, Remote Programming.
18 RS Lock Func�on No Change UL Before L A�er UL Before Start Lock A�er Start
3. Cycle the ignition key OFF/ON. The system will beep and flash the parking lights two
5 Hood Open 19 Factory Disarm Output Single Pulse 350ms 500ms 800ms Door Lock Timing
(2) times for Feature Bank 2.
6 Low / No Tach 4. Press the valet button to cycle features. The LED will flash to display the feature 20 Pulse During Crank During Crank GWR Igni�on Accessory
number. 21 Factory Arm Output After Start GWR Igni�on Accessory Start
7 Tach Programming 5. Press the Start button to cycle options. The system will beep to indicate the option 22 Pulse A�er Shutdown After Shutdown GWR Igni�on Accessory Start
8 High Tach number. 23 Addi�onal Unlock Pulse NA
6. Cycle ignition key OFF/ON. The system will beep and flash the parking lights three (3)
Chirp Delete times for Feature Bank 3.
System ARM/DISARM chirps can be toggled ON or OFF without entering Feature Bank
programming.
7.
8.
Press the valet button to cycle features. The LED will flash to display feature number.
Press the Start to cycle options. The system will beep to indicate the option number. OEM Security
1.
2.
Turn the ignition key ON/OFF.
Press and release the valet button three (3) times. Data Protocol Selection This system can provide OEM level security. The system will monitor and trigger by the
analog hood input and all entry zone inputs from the FLCAN or other integration modules. Important Update
When an entry zone is detected the system will beep the vehicle horn and flash the parking The default Data Port Protocol of this system is ADS. If using an
The default data port protocol of this model is ADS (iDatalink 2-Way). This model is capable
The system will respond with one (1) chirp for ON and two (2) Chirps for OFF. This lights. This feature must be activated in Feature Bank 2, Feature 17. FLCAN or other external integration module be sure to choose
of detecting the correct data port protocol (ADS or DBI) and automatically configuring
feature will not affect alarm trigger or programming. Feature Bank 2; Feature 18. To initialize the detection procedure: iDatalink 2-Way when flashing.
User Programmable LED Operation
System LED notifications can be turned ON or OFF without entering Feature Bank To arm the system, press the start button one (1) time. This system will also support DBI. This will require programming
1. Press and hold the valet button.
To disarm the system, press the start button two (2) times. Feature Bank 2, Feature 18 to DBI.
programming. 2. Cycle the vehicle’s Ignition ON/OFF two (2) times.
3. Release the valet button. To start the system, press and hold the start button for three (3) seconds.
1. Turn the ignition key ON/OFF, ON/OFF.
2. Press and hold valet button for five (5) seconds. The system will automatically detect and set the correct data port protocol, ADS or DBI. Valet Override Procedure
To disarm the system without the use of a remote, turn the ignition key to ON and press
The LED will flash one (1) time for ON, two (2) times for OFF. This feature will not affect Note: This feature is only available on module firmware v2.0 or higher. the valet button one (1) time.
LED flash during programming.