APS57TM

Vehicle Remote Start / Keyless System

Installation and Reference Guide

Thank you for trusting Prestige products! If you are a consumer, please note:
Professional installation is strongly recommended.
This manual assumes the installer has adequate knowledge of the following expertise. Therefore, it does not
cover these topics in detail:
• 12-volt electronics
• Testing and verifying circuits
• Making safe and lasting wiring connections
• Factory ignition, power, lighting, data bus and sensing systems
• Factory systems and components to avoid
• Safe wire routing, circuit protection and product placement
• Access to vehicle-specific technical information

In addition, this manual assumes the installer has the proper tools, skill and facilities to perform a professional installation.
Performing an improper installation could result in damage to the vehicle or its components, improper system function,
unsafe vehicle operation or physical injury. Such instances would not be covered by the vehicle manufacturer's warranty,
nor by Voxx Electronics, Inc.

Detailed Descriptions Quick Reference

2 Wire Harness Colors and Functions 15 System Programming
2 Power Connector 15 Programming Mode Entry / Exit
3 Notification Connector 16 Feature Bank Options
4 Input / Output Connector 17 Data Port Protocol
17 Tach Function
6 External Components 17 Alarm Override
6 RF Antenna Kit 18 Silent Lock and Unlock
6 Data Bus Interface (DBI) 18 User Selectable LED
6 Telematics
6 Weblink Programming 18 System Diagnostics
18 Troubleshooting Remote Start
7 Setup Options
7 Remote Programming 19 Wiring Diagrams
8 Keyless Control 19 Door Lock Connections
10 Remote Start Control 22 Full System Connections

14 System Operation
14 Remote Operation

2020 Voxx Electronics Corporation. All rights reserved. APS57TM_RevD_07/20

 Detailed Descriptions: Wire Harness Colors and Functions
Power Connector (6-pin High-Current Connector) See page 22 for the full system diagram.
These wires are listed in order of their placement in the harness connector.

1 3 5
2 4 6

1. YELLOW – Starter Output for Remote Start (+)

The YELLOW wire supplies 12-Volt (+) to the vehicle’s starter wire when remote start is enabled, and turns off once the
vehicle is started.
Verification: This starter wire registers 12-Volt (+) during engine crank.

2. GREEN – Ignition 2 Output (+)

At its default setting, the GREEN wire supplies 12-Volt (+) to the vehicle’s secondary ignition wire during remote start.
Verification: If present, the secondary ignition wire registers 12-Volt (+) when the vehicle is in ignition mode AND during
engine crank.
Note: This wire can be programmed to perform a different function by changing its options. Refer to Bank 3, Feature 7
on page 10.

3. RED – 12-Volt Input (+)

The RED wire connects to the vehicle’s primary 12-Volt (+) wire to power the system.
Verification: The power wire registers 12-Volt (+) at all times.
Note: Before making this connection, remove all module fuses until the system is completely connected.

4. RED/WHITE – 12-Volt Input (+)

The RED/WHITE wire connects to the vehicle’s secondary 12-Volt (+) wire to power the remote start function.
Verification: The power wire registers 12-Volt (+) at all times.
Note: Before making this connection, remove all module fuses until the system is completely connected.

5. PURPLE – Accessory Output (+)

At its default setting, the PURPLE wire supplies 12-Volt (+) to the vehicle’s accessory wire to power vehicle accessories
during remote start.
Verification: The accessory wire registers 12-Volt (+) when the vehicle is running or in Accessory mode, but not during
engine crank or if the vehicle is off.
Note: This wire can be programmed to perform a different function by changing its options. Refer to Bank 3, Feature 9
on page 10.

6. BLUE – Ignition 1 Input / Output (+)

The BLUE wire supplies 12-Volt (+) to the vehicle’s primary ignition wire during remote start. This wire is also used to
sense vehicle ignition for the Programming Functions
Verification: The primary ignition wire registers 12-Volt (+) when the vehicle is in ignition mode AND during engine crank.

2 APS57TM_RevA_07/20
 Detailed Descriptions: Wire Harness Colors and Functions
Notification Connector (4-pin connector) See page 22 for the full system diagram.
These wires are listed in order of their placement in the harness connector.

1 3
2 4

1. WHITE – Parking Light Relay Output (Internal Relay Pin 30)

At its default setting, the WHITE wire supplies 12-Volt (+) or Ground (-) to the vehicle's park light wire based on the
connection of the relay input (WHITE/RED wire).
Verification: The vehicle parking light wire registers 12-Volt (+) or Ground (-) when the park lights are turned on.

2. WHITE/RED – Parking Light Relay Input (Internal Relay Pin 87)

The WHITE/RED connects to vehicle 12-Volt (+) or Ground (-) to supply the relay output (WHITE wire).
Verification for default setting:
• If the vehicle parking light wire registers 12-Volt (+) when the park lights are on, connect the WHITE/RED wire to a
constant 12-Volt (+) vehicle wire.
• If the vehicle parking light wire registers Ground (-) when the park lights are on, connect the WHITE/RED wire to a
reliable vehicle ground source.

3. YELLOW/BLACK – Ignition Output to Alarm (+)

The YELLOW/BLACK wire supplies 12-Volt (+) ignition output when the vehicle's ignition is set to ON, but not during the
remote start runtime. This output will be used when an external alarm system is added to the vehicle.

4. BLACK – Ground Input (-)

The BLACK wire connects to a reliable vehicle ground (-) source to power the system.
Verification: The vehicle ground (-) source wire registers ground (-) at all times.
Note: Before making this connection, remove all module fuses until the system is completely connected.

APS57TM_RevA_07/20 3
Detailed Descriptions: Wire Harness Colors and Functions
Input / Output Connector (14-pin connector) See page 22 for the full system diagram.
These wires are listed in order of their placement in the harness connector.

1 3 5 7 9 11 13
2 4 6 8 10 12 14

1. BLACK/WHITE – Horn Output (-)

The BLACK/WHITE wire connects to the vehicle's horn wire and supplies Ground (-) when activated from the system.
Verification: The vehicle horn wire registers Ground (-) when the horn is activated.

2. RED – Door Lock (-)

The RED wire supplies Ground (-) when the Lock function is activated from the remote control or system.
Verification: The vehicle lock wire registers 12-Volts (+) or Ground (-) when the Lock button is activated. Additional parts
may be required. See Page 19 for common door lock wire diagrams.

3. GRAY/BLACK – Hood Input (-)

The GRAY/BLACK wire connects to the vehicle's hood switch, or an installed switch that registers Ground (-) when
triggered.
Verification: The vehicle hood switch wire registers Ground (-) when the hood is opened.

4. GREEN – Door Unlock (-)

The GREEN wire supplies Ground (-) when the Unlock function is activated from the remote control or system.
Verification: The vehicle lock wire registers 12-Volt (+) or Ground (-) when the Unlock button is activated. Additional parts
may be required. See Page 19 for common door lock wire diagrams.

5. LIGHT BLUE – Remote Start Status Output (-)

The LIGHT BLUE wire supplies Ground (-) as soon as the remote starter is activated and remains active until 4 seconds
after remote start run time has ended. This wire is most commonly used to activate data integration modules.

6. DARK BLUE/BLACK -- External Start Input (-)

The DARK BLUE/BLACK wire connects to a device or switch that, when triggered, supplies a Ground (-) output. If the
vehicle ignition is off, this input will activate the remote start function.

7. BLACK/LIGHT GREEN – Factory Arm Output (-)

At its default setting, the BLACK/GREEN wire supplies a Ground (-) pulse when the system is armed and when the
vehicle has been successfully started using remote start. It is typically used to re-lock vehicle doors after remote start if
necessary.
Note: This wire can be programmed to perform a different function by changing its options. Refer to Bank 3, Feature 21
on page 10.

8. BROWN/BLACK – Brake Input (+)

The BROWN/BLACK wire connects to the vehicle's brake wire to supply brake status for remote start.
Verification: The vehicle brake wire registers 12-Volts (+) when the brake is activated.

9. BLACK/BLUE – Factory Disarm Output (-)

The BLACK/BLUE wire supplies a Ground (-) pulse when the system is disarmed and when remote start is activated.
Verification: In most vehicles the vehicle factory disarm wire registers Ground (-) if the driver door key cylinder is turned
to the unlock position.
Note: This wire can be programmed to perform a different function by changing its options. Refer to Bank 3, Feature 19
on page 10.
4 APS57TM_RevA_07/20
 Detailed Descriptions: Wire Harness Colors and Functions
Input / Output Connector (14-pin connector) (Cont.) See page 22 for the full system diagram.
These wires are listed in order of their placement in the harness connector.

10. DARK BLUE – Trunk Release Output (-)

At its default setting, the DARK BLUE wire connects to the vehicle trunk release wire or relay and supplies Ground (-)
when activated from the remote control.
Verification: The vehicle trunk release wire registers 12-Volt (+) or Ground (-) when the trunk release button is activated.

11. BLACK/RED – Pulse After Shutdown Output (-)

At its default setting, the BLACK/RED wire supplies a Ground (-) pulse when the remote start system is shut down. It
is typically used to re-lock vehicle doors after remote start shutdown, or pulse the vehicle's door trigger to turn off
accessories after vehicle shutdown.
Note: This wire can be programmed to perform a different function by changing its options. Refer to Bank 3, Feature 22
on page 10.

12. GREEN/YELLOW – Diesel Glow Plug Input (+)

The GREEN/YELLOW wire connect to the vehicle's Diesel Glow Plug detection wire.
Verification: This wire will register as 12-Volt (+) while the Diesel Wait to Start Light is illuminated.

13. BLACK/YELLOW – Pulse During Crank Output (-)

At its default setting, the BLACK/YELLOW wire supplies a Ground (-) pulse when the engine cranks during remote start.
Note: This wire can be programmed to perform a different function by changing its options. Refer to Bank 3, Feature 20
on page 10.

14. GREEN/ORANGE – Tach Input

The GREEN/ORANGE wire connects to the vehicle’s tach wire at the negative side of the ignition coil or fuel injector to
control engine crank during remote start.
Verification:
• Using a voltmeter set to AC volts, connect the voltmeter’s positive lead to a constant vehicle
12-Volts (+) source and the negative lead to the wire to be tested.
• Start the engine and have a partner slowly press the gas pedal while the transmission is in Park. If the voltage
increases as the RPM increases, this is the proper tach wire.

APS57TM_RevA_07/20 5
 Detailed Descriptions: External Components
RF Antenna / LED / Programming Port
The long-range antenna kit (included) plugs into a 6-pin connector on the Prestige module.
1. Mount the supplied antenna/receiver to a clear spot on the vehicle’s windshield that will not
block the driver’s vision. A suitable location is high on the windshield near the rear-view mirror.
2. Be careful not to mount the antenna/receiver on any metallic window film, as this will affect
system range.
3. Route the antenna/receiver cable to the Prestige module, ensuring it does not block or interfere with deployment of
the airbag (if equipped.) Plug into the antenna port.

Data Bus Interface (DBI) Port

The 4-pin Data Bus Interface enables a FlashLogic door lock or transponder interface to connect to and communicate
with the vehicle data bus. The combined system saves installation time as many features that normally require individual
connection can be accessed and controlled through the data bus. Please refer to the D2D (Data to Data) function list
available per vehicle at www.FlashLogic.com.

FLCART Cartridge Port

This port is for installing the FlashLogic FLCART data immobilizer & door lock interface cartridge used to communicate
with the vehicle’s databus.

Weblink Programming Port

This 4-pin port is used for programming the FlashLogic FLCART interface cartridge via the FLPROG Weblink or Weblink
Mobile. Refer to the FlashLogic website for more details.

FLCART Harness Port

This port is for the harness included with the FLCART interface cartridge. Refer to the FlashLogic website for more details.

Telematics Interface
The 4-pin Telematics port enables a connected interface such as CarLink to expand system control to a smartphone or
tablet. The following features may be able to be activated from a connected device:
• Door Lock Control
• Remote Start
• Trunk Release
• Auxiliary Output*
• Sliding Doors*

Weblink Programming
This port can also be used to connect your FlashLogic Weblink for feature programming and software updating. Once
connected please visit www.flashlogic.com.

* Must be supported by FLCAN

6 APS57TM_RevA_07/20
 Detailed Descriptions: Setup Options
Bank 1: Add / Remove Remote Controls See page 15 for Programming Instruction.
Remote programming is located in Feature Bank 1. This system will Auto Program basic functions of the remote with one
(1) button press. Basic functions are channels 1-3, Lock, Unlock, and Trunk / Start.

Feature Bank 1 Descrip�on

1 Auto Program/Lock Press Lock bu�on on remote
2 Unlock Press Unlock bu�on on remote
CH.
3 Trunk/Start Press Start bu�on on remote

To Auto Program a remote control:

1. Turn the ignition key to ON.
2. Press and release the valet button three (3) times.
3. The system will beep one (1) time, indicating you have accessed Bank 1, Remote Programming.
4. Press the Lock button of each remote control you wish to program. (Channels 1-3 of the remote control will be
programmed.) The system will beep one (1) time when each remote control is added.
5. Turn the ignition key to OFF to exit programming mode, or cycle the ignition key OFF/ON to advance to the next
Feature Bank.

To delete a remote control:

This system will store a maximum of four (4) remote controls in the memory. Additional programmed remote controls
will delete the oldest-programmed remote control.

Deleting All Remotes:

1. Perform steps 1-3 above.
2. Press and hold the valet button for five (5) seconds.
3. The system will sound one (1) long beep. This indicates all remotes have been deleted from memory.

Notes:
• The system will store in the memory a maximum of four (4) remote controls. Additional programmed
remote controls will delete the oldest-programmed remote control.
• During normal operation, the Programmed Transmitter Notification (PTN) function indicates how many
remote controls are programmed by flashing the LED a certain number of times when the vehicle ignition is
turned on.

APS57TM_RevA_07/20 7
 Detailed Descriptions: Setup Options
Keyless Control (Bank 2) See page 15 for Programming Instruction.

Op�ons
Feature Bank 2 1 Chirp 2 Chirp 3 Chirp 4 Chirp 5 Chirp 6 Chirp
1 Lock / Unlock Func�on 500ms 3.5sec 500ms L, DBL UL DBL L, 500ms UL DBL L, DBL UL 500ms L, 350ms UL
2 Accessory Lock NA
3 Accessory Unlock NA
4 Exterior Illumina�on NA
5 Auto Relock NA
6 Auto Arming NA
7 No�fica�on Sound NA
8 Horn Timing 16ms 30ms 40ms 50ms 10ms
Features

9 Valet Override Method NA

10 Driver Priority Unlock NA
11 Silent Choice OFF From Transmi�er OEM Style
12 Park Light / Trunk Swap NA
13 AUX Ch. 4 NA
14 AUX Ch. 5 NA
15 AUX Ch. 6 NA
16 AUX Ch. 7 NA
17 Security Profile OFF OEM Security W/ OEM Remote Start
18 Data Port Protocol ADS DBI

Feature 1: Lock / Unlock Function

Function: Set the lock / unlock output timing and functionality for specific vehicle lock types.
Setting Choices:
• Option 1 - Lock and Unlock outputs will pulse for 500 milliseconds.
• Option 2 - Lock and Unlock outputs will pulse for 3.5 seconds.
• Option 3 - Lock output will pulse for 500ms ; Unlock output will pulse twice, 500ms each.
• Option 4 - Lock output will pulse twice, 500ms each ; Unlock output will pulse for 500ms.
• Option 5 - Lock and Unlock outputs will pulse twice for 500ms.
• Option 6 - Lock output will pulse for 500ms ; Unlock output will pulse for 350ms.

Feature 2: Accessory-Activated Lock

This Feature is not available on this model.

Feature 3: Accessory-Activated Unlock

This Feature is not available on this model.

Feature 4: Exterior Illumination

This Feature is not available on this model.

Feature 5: Auto ReLock Setting

This Feature is not available on this model.

Feature 6: Automatic Arming

This feature is not available on this model.

Feature 7: Notification Sounds

This feature is not available on this model.

8 APS57TM_RevA_07/20
 Detailed Descriptions: Setup Options
Keyless Control (Bank 2) (cont.) See page 15 for Programming Instruction.
Feature 8: Horn Output Duration
Function: Set the horn output to activate for a set time.
Setting Choices:
• Option 1 - Output pulses for 16 milliseconds.
• Option 2 - Output pulses for 30 milliseconds.
• Option 3 - Output pulses for 40 milliseconds.
• Option 4 - Output pulses for 50 milliseconds.
• Option 5 - Output pulses for 10 milliseconds.

Feature 9: Override Method

This feature is not available on this model.

Feature 10: Driver Priority Unlock

This Feature is not available on this model.

Feature 11: Silent ChoiceTM

Function: Set audible beeps on or off when arming and disarming the system.
Setting Choices:
• Option 1 - Pressing Lock or Unlock at any time will perform the function with audible beeps.
• Option 2 - Pressing Lock or Unlock for 1.5sec on remote will control system without an audible beep.
• Option 3 - First press of Lock or Unlock on the remote control will perform the function without an audible
sound. Second press within 10sec will result in audible beeps.

Feature 12: Park Light / Trunk Relay Function

This Feature is not available on this model.

Feature 13 - 19: AUX Ch. 4 Output

This Feature is not available on this model.

Feature 14 - 19: AUX Ch. 5 Output

This Feature is not available on this model.

Feature 15 - 19: AUX Ch. 6 Output

This Feature is not available on this model.

Feature 16 - 19: AUX Ch. 7 Output

This Feature is not available on this model.

Feature 17: Security Profile

Function: Set the system to function as a keyless entry / convenience system or full-featured alarm / convenience
system.
Setting Choices:
• Option 1 - OFF, no security protection.
• Option 2 - OEM Security, entry zone protection.
• Option 3 - w/ OEM Remote Start, entry zone protection with OEM remote start compatibility.

Feature 18: Data Bus (DBI) Port Protocol

Function: Set functionality of the data bus connector to accept integration modules of differing protocols.
Setting Choices:
• Option 1 - The data bus connector will be configured to work with modules that use the ADS Protocol.
• Option 2 - The data bus connector will be configured to work with modules that use the DBI Protocol.
APS57TM_RevA_07/20 9
 Detailed Descriptions: Setup Options

Remote Start Control (Bank 3) See page 15 for Programming Instruction.

Op�ons
Feature Bank 3 1 Chirp 2 Chirp 3 Chirp 4 chirp 5 Chirp 6 Chirp
1 Defrost Output NA
2 RS Start No�fica�on ON OFF
3 RS Run�me 15min 20min 45min 60min 5min 10min
4 RS Parking Lights Steady Flashing
5 Engine Confirma�on Tach Voltage Data Hybrid
6 Voltage Level >0.5v B4 Start <0.5v B4 Start
7 Igni�on 2 Output Ignition Accessory Start
8 Igni�on 3 Output N/A
9 Accessory Output Accessory Igni�on Start
10 Transmission NA
11 Max Crank Time 0.8sec 1.0sec 1.5sec 2.0sec 3.0sec 4.0sec
Features

12 Diesel Delay OFF Diesel 5 Diesel 10 Diesel 15 Diesel 20 Diesel 30

13 Temperature Start NA
14 Crank Dura�on Averaging Preset
15 RS Shock Override NA
16 Turbo Timer NA
17 Start Ac�va�on Two Press One Press Three Press
18 RS Lock Func�on No Change UL Before L A�er UL Before Start Lock A�er Start
19 Factory Disarm Output Single Pulse 350ms 500ms 800ms Same As Bank 2, F1
20 Pulse During Crank During Crank GWR Igni�on Accessory
21 Factory Arm Output After Start GWR Igni�on Accessory Start
22 Pulse A�er Shutdown After Shutdown GWR Igni�on Accessory Start
23 Addi�onal Unlock Pulse No Pulse IGN, ACC, GWR IGN,ACC,GWR,PASD

Feature 1: Defrost Output Duration

This Feature is not available on this model.

Feature 2: Remote Start Notification

Function: Set remote start activation confirmation beeps on or off.
Setting Choices:
• Option 1 - On - System emits an audible beep when remote start is activated.
• Option 2 - OFF -System remains silent when remote start is activated.

Feature 3: Remote Start Run Time

Function: Set the maximum remote start run time if the vehicle is not entered after activation.
Setting Choices:
• Option 1 - Engine will run for 15 minutes.
• Option 2 - Engine will run for 20 minutes.
• Option 3 - Engine will run for 45 minutes.
• Option 4 - Engine will run for 60 minutes.
• Option 5 - Engine will run for 5 minutes.
• Option 6 - Engine will run for 10 minutes.

Feature 4: Remote Start Parking Light Duration

Function: Set parking light output to turn on or flash lights during remote start.
Setting Choices:
• Option 1 - Lights remain on during remote start.
• Option 2 - Lights flash during remote start.

10 APS57TM_RevA_07/20
 Detailed Descriptions: Setup Options

Remote Start Control (Bank 3) (cont.) See page 15 for Programming Instruction.
Feature 5: Engine Confirmation
Function: Determine how the system knows if remote start was successful.
Setting Choices:
• Option 1 - Determined by measurement from the Purple/White Tach Input wire.
• Option 2 - Determined by the voltage difference before remote start and after as set in Bank 3, Feature 6.
• Option 3 - Receives information through an attached data bus interface.
• Option 4 - No sensing; assumes vehicle has started based on setting in Bank 3, Features 11 & 14.

Feature 6: Start Sensing Voltage Level

Function: Set the sensitivity of voltage variance measurement to determine if the vehicle has started when Feature 5 is
set to option 2, Voltage.
Setting Choices:
• Option 1 - High: Voltage difference before remote start and after must be greater than .5 volts.
• Option 2 - Low: Voltage difference before remote start and after must be less than .5 volts.

Feature 7: Ignition 2 Output Function (Green)

Function: Set the functionality of the programmable Ignition 2 output.
Setting Choices:
• Option 1 - Wire sends 12-Volt (+) during ignition and start.
• Option 2 - Wire sends 12-Volt (+) during ignition; drops out during start.
• Option 3 - Wire sends 12-Volt (+) during start only.

Feature 8: Ignition 3 Output Function (Pink)

This Feature is not available on this model.

Feature 9: Accessory Output Function (Purple)

Function: Set the functionality of the programmable Accessory output.
Setting Choices:
• Option 1 - Wire sends 12-Volt (+) during ignition; drops out during start.
• Option 2 - Wire sends 12-Volt (+) during ignition and start.
• Option 3 - Wire sends 12-Volt (+) during start only.

Feature 10: Transmission Type

This Feature is not available on this model.

Feature 11: Maximum Crank Time

Function: Set maximum crank time for all remote start settings.
Setting Choices:
• Option 1 - Starter will crank for .8 seconds.
• Option 2 - Starter will crank for 1 second.
• Option 3 - Starter will crank for 1.5 seconds.
• Option 4 - Starter will crank for 2 seconds.
• Option 5 - Starter will crank for 4 seconds.

APS57TM_RevA_07/20 11
 Detailed Descriptions: Setup Options
Remote Start Control (Bank 3) (cont.) See page 15 for Programming Instruction.
Feature 12: Diesel (Pre-Start) Delay
Function: After remote start ignition is activated, set delay of crank to accommodate diesel engines.
Setting Choices:
• Option 1 - Vehicle starts immediately after remote start ignition.
• Option 2 - Start is delayed for 5 seconds after remote start ignition.
• Option 3 - Start is delayed for 10 seconds after remote start ignition.
• Option 4 - Start is delayed for 15 seconds after remote start ignition.
• Option 5 - Start is delayed for 20 seconds after remote start ignition.
• Option 6 - Start is delayed for 45 seconds after remote start ignition.
Feature 13: Temperature-Based Start Setting
This Feature is not available on this model.

Feature 14: Crank Duration

Function: Set how the system will determine how long to crank the starter.
Setting Choices:
• Option 1 - Starter will crank based on average of last 8 times the vehicle was started with the key.
• Option 2 - Starter will crank for maximum time as set in Bank 3, Feature 11.

Feature 15: Shock Sensor Control

This feature is not available on this model.

Feature 16: Turbo Timer Setting

This Feature is not available on this model.

Feature 17: Remote Start Activation

Function: Set remote start to activate with one, two, or three presses from the remote control or pulses detected on
the Dark Blue/Black External Activation Input.
Setting Choices:
• Option 1 - Press the Start button 2 times for remote start.
• Option 2 - Press the Start button 1 time for remote start.
• Option 2 - Press the Start button 3 times for remote start.

Feature 18: Remote Start Lock Control

Function: If desired, set door lock outputs to function before or after remote start.
Setting Choices:
• Option 1 - Remote Start Lock Control is inactive.
• Option 2 - Doors will unlock before remote start; lock after remote start.
• Option 3 - Doors will unlock before remote start.
• Option 4 - Doors will lock after remote start.

Feature 19: Factory Disarm Output Function (BLACK/BLUE)

Function: Set the functionality of the programmable output.
Setting Choices:
• Option 1 - Sends a 1-second pulse before start and during Unlock.
• Option 2 - Sends a 350ms pulse before start and during Unlock.
• Option 3 - Sends a 500ms pulse before start and during Unlock.
• Option 4 - Sends a 800ms pulse before start and during Unlock.
• Option 5 - Sends a pulse before start and during unlock based on setting of Bank 2, Feature 1.

12 APS57TM_RevA_07/20
 Detailed Descriptions: Setup Options
Remote Start Control (Bank 3) (Cont.) See page 15 for Programming Instruction.
Feature 20: Pulse During Crank Output Function (BLACK/YELLOW)
Function: Set the functionality of the programmable output.
Setting Choices:
• Option 1 - Pulse During Crank.
• Option 2 - GWR, Remote Start Status Output.
• Option 3 - Ignition Timing.
• Option 4 - Accessory Timing.

Feature 21: Factory Arm Output Function (BLACK/LIGHT GREEN)

Function: Set the functionality of the programmable output.
Setting Choices:
• Option 1 - Pulse After Start Output.
• Option 2 - GWR, Remote Start Status Output.
• Option 3 - Ignition Output.
• Option 4 - Accessory Output.
• Option 5 - Start Output.

Feature 22: Pulse After Shutdown Output Function (BLACK/RED)

Function: Set the functionality of the programmable output.
Setting Choices:
• Option 1 - Pulse After Shutdown Output.
• Option 2 - GWR, Remote Start Status Output.
• Option 3 - Ignition Output.
• Option 4 - Accessory Output.
• Option 5 - Start Output.

Feature 23: Additional Unlock Pulses

Function: Set other outputs to pulse when the vehicle is unlocked with the remote control.
Setting Choices:
• Option 1 - No additional unlock pulses.
• Option 2 - Pulse Ignition, Accessory and Ground While Running wires upon Unlock.
• Option 3 - Pulse Ignition, Accessory, Ground While Running, and Pulse After Shutdown wires upon unlock.

APS57TM_RevA_07/20 13
 Detailed Descriptions: System Operation

Remote Control Operation

This system includes two (2) remote controls. The matrix below describes the basic functions of each remote. See
Owners Guide for complete remote operation matrix.

Three Button Remotes (1-Way)

Button Action Function

Press 1x Lock
Hold 3 Seconds Panic ON/OFF
Press 1x Unlock
Hold 3 Seconds Panic ON/OFF
Press 2x Start (Programable)
Hold 3 Seconds Trunk Release
Press 1x
Programable AUX
Press & Hold
Press 1x
Programable AUX
Press & Hold

14 APS57TM_RevA_07/20
 Quick Reference: System Programming

Programming Mode Entry and Exit Procedure

Once the system is installed and powered up, you will use the vehicle ignition, override button and a programmed
remote control to set all system options. Feature options are divided into categories, or Banks, as described throughout
this section. Ensure that at least one remote control is programmed to the system. If not, or if you need to program
more remote controls, use the diagram steps to access Bank 1.
The siren and LED will indicate your status and selections. Follow the diagram below to enter and maneuver through the
programming procedure.

3X 1X
ON ON
CC CC
ST
CK A

ST
CK A
ART

2 = Bank 2
ART
LO

3 = Bank 3
LO

Ignition On Press and Release 1 Chirp = Bank 1 Cycle Key to Advance Chirps Indicate Press Override Button to LED Indicates Press to Change Chirps Indicate
Override Button (Program Remotes) Banks (2,3) Bank Number Advance Within Bank Feature Selection Feature Option Option Number

... or Exit Repeat Steps to Program Repeat Steps to Program

ON Another Feature ...
CC Programming Another Feature Bank...
ST
CK A

ART
LO

Note: Programming will time out after 60sec with no activity or Ignition Off for 5sec.
Ignition Off

1. Turn the ignition ON.

2. Press and release the valet button three (3) times.
3. The system will beep (1) one time, indicating you have accessed Bank 1.
4. Each cycle of the Ignition, OFF/ON, will advance to the next bank (up to Bank 3) then restart at Bank 2. (Note: To re-
access Bank 1 for transmitter programming, you will need to exit and re-enter programming mode.)
5. The system will beep a number of times to indicate the Bank number:
• 1 beeps: Bank 1 - Programming Remote Controls
• 2 beeps: Bank 2 - Keyless Control Options
• 3 beeps: Bank 3 - Remote Start Control Options

6. Once you have accessed the desired bank, press the valet button to advance though the features. The LED will flash a
number of times to indicate the feature, based on the charts that follow this section. The system will chip a number
of times to indicate the Option programmed.
7. Once you have accessed the desired feature, press the LOCK button on the remote control to advance though the
feature's setting options. The system will beep a number of times to indicate the Option setting, based on the charts
that follow this section.
8. Once you have made the desired setting, you can press the valet button to advance through the
features within the bank, or cycle the Ignition key OFF/ON to advance to the next bank.
9. Once you have completed programming, you MUST turn the ignition key to OFF to exit the programming
mode. Programming will automatically exit after 60 seconds of inactivity.

APS57TM_RevA_07/20 15
 Quick Reference: System Programming

Bank 1: Transmitter Programming Options See page 7 for a detailed description.

Feature Bank 1 Descrip�on

1 Auto Program/Lock Press Lock bu�on on remote
2 Unlock Press Unlock bu�on on remote
CH.
3 Trunk/Start Press Start bu�on on remote

Bank 2: Keyless Options See pages 8-9 for detailed descriptions.

Op�ons
Feature Bank 2 1 Chirp 2 Chirp 3 Chirp 4 Chirp 5 Chirp 6 Chirp
1 Lock / Unlock Func�on 500ms 3.5sec 500ms L, DBL UL DBL L, 500ms UL DBL L, DBL UL 500ms L, 350ms UL
2 Accessory Lock NA
3 Accessory Unlock NA
4 Exterior Illumina�on NA
5 Auto Relock NA
6 Auto Arming NA
7 No�fica�on Sound NA
8 Horn Timing 16ms 30ms 40ms 50ms 10ms
Features

9 Valet Override Method NA

10 Driver Priority Unlock NA
11 Silent Choice OFF From Transmi�er OEM Style
12 Park Light / Trunk Swap NA
13 AUX Ch. 4 NA
14 AUX Ch. 5 NA
15 AUX Ch. 6 NA
16 AUX Ch. 7 NA
17 Security Profile OFF OEM Security W/ OEM Remote Start
18 Data Port Protocol ADS DBI

Bank 3: Remote Start Options See pages 10-13 for detailed descriptions.
Op�ons
Feature Bank 3 1 Chirp 2 Chirp 3 Chirp 4 chirp 5 Chirp 6 Chirp
1 Defrost Output NA
2 RS Start No�fica�on ON OFF
3 RS Run�me 15min 20min 45min 60min 5min 10min
4 RS Parking Lights Steady Flashing
5 Engine Confirma�on Tach Voltage Data Hybrid
6 Voltage Level >0.5v B4 Start <0.5v B4 Start
7 Igni�on 2 Output Ignition Accessory Start
8 Igni�on 3 Output N/A
9 Accessory Output Accessory Igni�on Start
10 Transmission NA
11 Max Crank Time 0.8sec 1.0sec 1.5sec 2.0sec 3.0sec 4.0sec
Features

12 Diesel Delay OFF Diesel 5 Diesel 10 Diesel 15 Diesel 20 Diesel 30

13 Temperature Start NA
14 Crank Dura�on Averaging Preset
15 RS Shock Override NA
16 Turbo Timer NA
17 Start Ac�va�on Two Press One Press Three Press
18 RS Lock Func�on No Change UL Before L A�er UL Before Start Lock A�er Start
19 Factory Disarm Output Single Pulse 350ms 500ms 800ms Same As Bank 2, F1
20 Pulse During Crank During Crank GWR Igni�on Accessory
21 Factory Arm Output After Start GWR Igni�on Accessory Start
22 Pulse A�er Shutdown After Shutdown GWR Igni�on Accessory Start
23 Addi�onal Unlock Pulse No Pulse IGN, ACC, GWR IGN,ACC,GWR,PASD

16 APS57TM_RevA_07/20
 Quick Reference: System Programming & Diagnostics
Data Port Protocol Selection
The default data port protocol of this model is ADS (iDatalink 2-Way). This model is capable of detecting the correct
data port protocol (ADS or DBI) and automatically configuring Feature Bank 2; Feature 18. To initialize the detection
procedure:
1. Press and hold the valet button.
2. Cycle the vehicle’s Ignition ON/OFF two (2) times.
3. Release the valet button.
Note: This feature is only available on module firmware v2.00 or higher.

Tach Function
When using the GREEN/ORANGE tach wire, the vehicle tach rate must be programmed.

Programming with valet button when tach wire is connected:

1. Turn the ignition key to the ON position.
2. Press and release the valet button three (3) times.
3. Immediately turn the ignition key OFF.
4. Press and hold the valet button, then start the vehicle using the key.
5. When the unit senses the tach signal, the parking lights will begin to flash.
6. Allow the vehicle to settle to a normal idle speed.
7. Release the valet button.

The parking lights will turn on for two (2) seconds and one (1) long chip will indicate that the learned tach signal is stored
and the unit has exited tach learn mode.

Programming without valet button when tach wire is connected:

1. Turn the ignition key to the ON position and start the vehicle's engine.
2. Wait for Engine RPM to lower to a normal idle.
3. Press and hold the vehicle's brake pedal.
4. Press the LOCK button on the OEM remote or the Carlink App.

The vehicle's parking lights will flash seven (7) times to indicate the tach signal has been learned. If the parking lights do
not flash, locate another tach source and repeat steps 1 - 4 above.

Note: Programming tach signal via OEM or Telematics control is only available on Firmware v1.47 or Higher.

Valet Alarm Override (Optional)

The Valet Override procedure will disable the alarm when the remote is not available or has become inoperative. If the
vehicle door is opened without disarming, the alarm will sound and the vehicle will not start when attempting to start
with the key. To disable the alarm:
1. Turn the vehicle ignition to ON.
2. Within 5sec, press and release valet button one (1) time.
The alarm will silence and the vehicle will now start normally with the key.

APS57TM_RevA_07/20 17
 Quick Reference: System Programming & Diagnostics

Silent Lock and Unlock

Program the Prestige system to Lock and Unlock without notification beeps.
1. Turn the ignition ON then OFF.
2. Press and release the valet button three (3) times. The system will respond with one (1) beep for ON or two (2) beeps
for OFF.

User Selectable LED

This feature will control whether the LED is ON or OFF when the system is Armed/Locked. This will be selectable in
feature programming OR on-the-fly without entering the programming feature banks.
1. Turn the ignition ON, OFF, ON, OFF.
2. Press and hold valet button for five (5) seconds.
The LED will flash one (1) time for ON, two (2) times for OFF. This feature will not affect LED flash during programming.

Troubleshooting Remote Start

All Prestige remote start system will provide parking light feedback to display remote start errors or shutdowns. The
vehicle parking lights will flash to display error or shutdown code.

1 Run�me Expired
2 Remote Shutdown
3 Brake On
4 Manual Mode
5 Hood Open
6 Low / No Tach
7 Tach Programming
8 High Tach

18 APS57TM_RevA_07/20
 Quick Reference: Wiring Diagrams

Door Lock Connections

Negative-Trigger Door Locks

Verification: The vehicle wires register Ground when the Lock and Unlock switches are activated.

RED ( - ) Lock Output

Lock
Vehicle Door Lock
Control Relays
Unlock

GREEN ( - ) Unlock Output

Positive-Trigger Door Locks

Verification: The vehicle wires register 12V+ when the Lock and Unlock switches are activated.

Fused +12 Volt

Battery Souce
87

87a
86 85 RED ( - ) Lock Output

30

Lock
Vehicle Door Lock Fused +12 Volt
Control Relays Battery Souce
Unlock 87

87a
86 85 GREEN ( - ) Unlock Output

30

APS57TM_RevA_07/20 19
 Quick Reference: Wiring Diagrams

Door Lock Connections

Single-Wire Negative Multiplex Door Locks (Relays required)
Verification: The vehicle wire registers variable Ground values when the Lock and Unlock switches are activated. Please
consult the vehicle-specific wire and location chart for resistor values.

Ground

87 87

RED ( - ) Lock Output 87a Fused +12 Volt 87a Green ( - ) Unlock Output
86 85 Battery Source 86 85
30 30

Lock Resistor
Vehicle Door Lock
Control Relays
Unlock

Single-Wire Positive Multiplex Door Locks (Relays required)

Verification: The vehicle wire registers variable 12V+ values when the Lock and Unlock switches are activated. Please
consult the vehicle-specific wire and location chart for resistor values.

87 87

RED ( - ) Lock Output 87a Fused +12 Volt 87a Green ( - ) Unlock Output
86 85 Battery Source 86 85
30 30

Lock Resistor
Vehicle Door Lock
Control Relays
Unlock

20 APS57TM_RevA_07/20
 Quick Reference: Wiring Diagrams

Door Lock Connections

Reverse-Polarity Door Locks (Relays required)
Verification: The vehicle wires rest at Ground and register 12V+ when the Lock and Unlock switches are activated.

Fused +12 Volt

Battery Souce
87

87a
86 85 RED ( - ) Lock Output

30

Lock
X To Door Lock Motor

Unlock
Cut
Fused +12 Volt
Battery Souce
87

87a
86 85 Green ( - ) Unlock Output

30

X To Door Lock Motor

Cut

Aftermarket Actuators (Relays and door lock actuators required)

Fused +12 Volt

Batter y Source
87
Door Lock
Actuator 87a RED ( - ) Lock Output
86 85
30
Chassis
Ground
M

Fused +12 Volt

Batter y Source
87

87a GREEN ( - ) Unlock Output

86 85
30
Chassis
Ground

APS57TM_RevA_07/20 21
22
4180070 183BP 183BP

14 Green/Orange Tach Input

13 Black/Yellow Pulse During Crank Output (-)
12 Green/Yellow Glow Plug Input (+)
11 Black/Red Pulse AŌer Shutdown Output (-)
13 14 10 Dk. Blue Trunk Output (-)
11 12 9 Black/Blue Factory Disarm Output (-)
9 10
8 Brown/Black Brake Input (+)
7 8
5 6 7 Black/Lt. Green Factory Arm Output (-)
3 4 6 Dk. Blue/Black External AcƟvaƟon Input (-)
1 3 5 1 2 5 Lt. Blue Remote Start Status Output (-)
14 Pin Main Input/Output

2 4 6 4 Green Unlock Output (-)

3 Gray/Black Hood Input (-)
1 Yellow Starter Output (+) 2 Red Lock Output (-)
2 Green IgniƟon 2 Output (+) P 1 Black/White Horn Output (-)
3 Red BaƩery 12V Input (+) FLCART Dock Replacement Part #4120476
4 Red/White BaƩery 12V Input (+)
5 Purple Accessory Output (+) P 1 4 Red BaƩery 12V (+)

6 Pin RS Harness
6 Blue IgniƟon Input / Output (+) 2 3 Blue Data TX
Replacement Part #4120467
DBI

3
Quick Reference: Wiring Diagrams

2 Black Ground (-)

4 1 White Data RX

VOXX
1 3
Accessory Sold Seperatly
2 4
4 4 Red BaƩery 12V (+)
1 White Parking Light (30) Output P 3 3 Blue Data TX
2 White/Red Parking Light (87) Input 2 2 Black Ground (-)
CarLink

3 Yellow/Black Ignition Output For Alarm (+) 1 1 White Data RX

4 Pin Light
4 Black Ground Input (-) Accessory Sold Seperatly
Replacement Part #4120463
19 20
1 2 3 4 Replacement Part #4361009 17 18
15 16
4 Red Battery 12V (+) 13 14 This Harness is included with the FLCART.
3 Black Ground (-) 11 12 For Wire Informa�on and Diagram Please Refer to Vehicle Specific
9 10 FlashLogic Install Guide.
2 White Data RX

Weblink
7 8 Visit www.FlashLogic.com for More Informa�on.
1 Blue Data TX
5 6
Accessory Sold Seperatly
3 4
1 2 3 4 5 6 1 2

1 Pink Ba�ery 5V (+)

2 Green Data RX
3 Black Ground (-)
4 Red Valet Switch
Antenna

5 Blue LED (-)

6 Empty Empty
Replacement Part #4120465

APS57TM_RevA_07/20