1.

Introduction
2. Basics of DMR Technology –
3. Overview- Mototrbo Digital Radios
4. Description and features of Mototrbo Digital Radio
5. Hands on Training on Mototrbo Radios.
6. CPS (Customer Programming Software Installation)
7. Programming of Mototrbo Radios ( How to enable or
disable features via CPS.
Mototrbo XiRP8668 and XiRM8668 radios are New Generation
Digital Radios based on ETSI-DMR standards and uses TDMA
(Time Division Multiple Access Technology).
 Digital mobile radio (DMR)

➢ Digital mobile radio (DMR) is an open digital mobile

radio standard defined in the European Telecommunications
Standards Institute (ETSI) Standard TS 102 361 parts 1–4.

➢ The DMR interface is defined by the following ETSI standards:

▪ TS 102 361-1: Air interface protocol

▪ TS 102 361-2: Voice and General services and facilities
▪ TS 102 361-3: Data protocol
▪ TS 102 361-4: Trunking protocol

➢ DMR was designed with three tiers.

▪ DMR tiers I and II (conventional) were first published in

2005

▪ DMR III (Trunked version) was published in 2012

 Digital mobile radio
Tier I
➢ Tier I is a single channel specification originally for the European
unlicensed dPMR446 service.
➢ IT is a single channel FDMA 6.25 kHz bandwidth;
➢ The standard supports
▪ peer-to-peer (mode 1),
▪ repeater (mode 2) and
▪ linked repeater (mode 3) configurations.

Tier II
➢ Tier II is 2-slot TDMA 12.5 kHz wide peer-to-peer and repeater mode
specification, resulting in a spectrum efficiency of 6.25 kHz per
channel.
➢ Each time slot can be either voice and/or data depending upon system
needs.
➢ IP Site Connect (IPSC) for interconnecting repeaters over the Internet is
 Digital mobile radio

Tier III
➢ Tier III builds upon Tier II, adding trunking operation involving
multiple repeaters at a single site.
➢ Not all manufacturers’ trunking implementation is Tier III
compatible.
➢ Vender specific protocols have expanded the trunking to
multiple site operations.
 Analog

Voice Vocoder

Mic

Digital
Over-the-Air

Analog

Vocoder Voice

Speaker
BLOCK DIAGRAM
Time-Division Multiple-Access (TDMA)?
Time-Division Multiple-Access (TDMA)
Enables splitting of channels to allow multiple access
on a single channel
Preserves full channel with but divides it into
alternating timeslots that can carry individual calls

❖One digital repeater replaces two analog repeaters

❖Reduces infrastructure, acquisition, setup, and
maintenance costs
❖Transmits more information
❖Supports more users
 TDMA

TDMA divides a 12.5 kHz channel into two alternating

time slots to achieve 6.25 kHz equivalent spectral
efficiency when used with a repeater.
Benefits of Digital Technologies
Spectrum Efficiency

Time

2 Voice Channels
TDMA)
1 2

12.5
KHz
 Why Digital
Increased Channel Capacity

Voice Call 1

Analog
 Why Digital
Increased Channel Capacity

Voice Call 1

Voice Call 2
Voice Call 2
Voice Call 1
Customer Requirements\Expectations

“Analogue Ceiling”

GP338

GP300

Police Cruiser HT1000

Time
 XiRP 8668 Radio Enhancements

Continuous Channel Knob Helical

Improves usability Antenna

On/Off Switch with Volume Orange Button

Control Short Press----Emergency
Off
Long Press ----Emergency
PTT button On
Best-in-Class Audio with loud
front-facing speaker
Side Button 1
Short Press ---- Keypad Lock On/Off
Long Press ---- All Audio On/Off

Side Button 2 5 Line Color Display

Short Press ---- -
Long Press ---- GPS On/Off
Side Button 3
Short Press ---- -
Long Press ---- Day / Night On/Off
P2
P1 Short Press ----Message
Short Press ----Contacts Long Press ---- Radio Name
Long Press ---- Manual Dial or
private

XIRP 8668
XiR P8668 portable radio
XiRM8668 Portable Radio

1 2 3 4 5 6

10 9 8 7
XiRM 8668 Mobile Radio
XiR P8668 / XiR M8668 Radio Display icons

 The following are the icons that appear on the radio’s

display.

Received Signal Strength Indicator (RSSI)

Battery

Bluetooth

Bluetooth Connected

Emergency
XiR P8668 / XiR M8668 Radio Display icons

Notifications
Scan

Scan – Priority

Scan – Priority 2
Vote Scan
Monitor
Talkaround

Site Roaming *

Secure
XiR P8668 / XiR M8668 Radio Display icons

Sent Successfully
The text message is sent
successfully.

Send Failed
The text message cannot be
sent.

In-Progress
 • 12.5 kHz channel

• 4-FSK modulation

• 2-slot TDMA channel

.Operating Temp 0-60

• Transmission can be used either for voice, data or generic signaling

• Frequency bands VHF/UHF/ MHz

Mobile Communications (I) Pvt. Ltd., New Delhi

 Advanced Parameters
1. Modulation 4 FSK
2. TDMA Time Slot 1/2
3. AMBE Vocoder
4. Color Code 0-15
5. AES 256 Bit Encryption
6. Operating Temp 0-60
7. Frequency bands VHF/UHF/ MHz
8. 12.5 kHz channel
9. Transmission can be used either for voice, data or generic
signaling

Mobile Communications (I) Pvt. Ltd., New Delhi

MOTOTRBO XiRP8668/ XiRM8668
 Features:-
◦ Radio ID / PTT ID
◦ Radio Check XiRP8668 -5W
◦ Call Alert
◦ Private Call
◦ Remote Monitor
◦ Radio Kill / Unkill
◦ SMS 138/278 Character
◦ Power On Password
◦ CPS Password
◦ GPS Facility XiRM8668 -25W
◦ Inbuilt Bluetooth
MOTOTRBO XiRP8668/ XiRM8668
• Features:-
– Emergency
– Scan with priority
– Bluetooth Facility
– DMO Mode (6.25e)
XiRP8668 -5W
– Over The Air Programming

XiRM8668 -25W
 AES 256 Bit Encryption
• Encryption based protection
• 16 keys
• AES 256 Bits encryption key
• Protects both Voice and Data. E.g. Text Messages, GPS data

Inherit Digital Encryption

• 2 possible Timeslot
• 15 possible color code (System ID)
• 16 million possible Group ID / Radio ID
• 3600 bps Vocoder
Several Group may be created in one Channel/Frequency
➢A Private Call may be made to any User with in the same Group
➢A Group Call may be used to call all user in the particular Group
➢All Call may be used to Call all groups in the same frequency

Frequency: ex- Frequency: ex- Frequency: ex-

159.55 Mhz 159.55 Mhz 159.55 Mhz
Group Id: 8000 Group Id: 9000 Group Id: 7000

SubC

SubC
SubA
SubA
SubB SubB

SubB SubC
SubA
CH-1 -------------159.55 Mhz------Group ID-1, Color Code-1----AES KEY 1
CH-2 -------------159.55 Mhz------Group ID-1, Color Code-2 ---AES KEY 2
CH-3 -------------159.55 Mhz------Group ID-1, Color Code-3 ---AES KEY 3
CH-4 -------------159.55 Mhz------Group ID-1, Color Code-4 ---AES KEY 4
CH-5 -------------159.55 Mhz------Group ID-1, Color Code-5-- -AES KEY 5
CH-6 -------------159.55 Mhz------Group ID-2, Color Code-6 ---AES KEY 6
CH-7 -------------159.55 Mhz------Group ID-3, Color Code-7 ---AES KEY 7
CH-8 -------------159.55 Mhz------Group ID-4, Color Code-7 ---AES KEY 8
CH-9 -------------159.55 Mhz------Group ID-5, Color Code-7 ---AES KEY 9
CH-10------------159.55 Mhz------Group ID-6, Color Code-7 ---AES KEY 10
 Petroling
EMERGENC
Y SIGNAL Group

Petroling Vehicle
 FEATURES

1. CONTACT
POWER
2. SCAN
ON 3. MESSAGE

UP/DOWN
MENU KEY TYPE THE MSG WITH
BUTTON THE HELP OF KEY
PAD
4321
 FEATURES
8. AFTER COMPOSING THE MSG
PRESS OK BUTTON
9. SEND MSG TO GROUP CALL /
SINGLE ID (MANUAL DIAL )

1. GROUP CALL
2. MANUAL DIAL
POWER
ON
10. TO SELECT GROUP CALL
(TO SEND MSG TO GROUP )
OR
( TO SELECT MANUAL DIAL )
11. PRESS OK BUTTON .
12 . TYPE THE RADIO ID TO WHOM
MSG IS TO BE SENT .
UP/DOWN
MENU KEY 13. PRESS OK BUTTON
BUTTON

4321
 FEATURES
HOW TO SEND QUICK TEXT
1. POWER ON
2. PASSWORD CLICK (4321
WITH
THE HELP OF KEY PAD )
3. PRESS MAIN MENU ON
DISPLAY 1. CONTACT
POWER
ON
2. SCAN
3. MESSAGE

4. TO SELECT THE MSG WITH THE

HELP OF UP/DOWN KEY.
5. PRESS OK BUTTON
UP/DOWN 6. PRESS DOWN KEY TO SELECT
MENU KEY THE
BUTTON QUICK TEXT WITH THE HELP
OF
4321
DOWN KEY
 FEATURES
TO SELECT THE MSG WITH THE
HELP OF UP/DOWN KEY .
9. PRESS OK
ON SCREEN
PROGRAMMABLE MSG WILL
DISPLAY (EX. :- PARTY
REACHED SAFELY )
POWER
ON 10. PRESS OK BUTTON
(TO SEND MSG TO GROUP )
OR
( TO SELECT MANUAL DIAL )
11. PRESS OK BUTTON .
12 . TYPE THE RADIO ID TO WHOM
MSG IS TO BE SENT .
UP/DOWN 13. PRESS OK BUTTON
MENU KEY
BUTTON

4321
 FEATURES
HOW TO CHECK
INBOX
1. POWER ON
2. PASSWORD CLICK (4321
WITH
POWER
THE HELP OF KEY PAD )
ON 3. PRESS MAIN MENU
1.ON DISPLAY
CONTACT
2. SCAN
3. MESSAGE

4. TO SELECT THE MSG WITH THE

UP/DOWN HELP OF UP/DOWN KEY.
MENU KEY 5. PRESS OK BUTTON
BUTTON
6 TO SELECT INBOX ( ALL MSG
4321 RECD WILL SHOWS )
 FEATURES
HOW TO RADIO CHECK
1. POWER ON
2. PASSWORD CLICK (4321
WITH
THE HELP OF KEY PAD )
3. PRESS MAIN MENU
POWER
4. GOTO CONTACT THEN PRESS
ON OK
5. PRESS UP KEY TO SELECT THE
MANUAL DIAL THEN PRESS
OK.
6. TYPE THE RADIO ID OF THE
RADIO TO BE CHECKED THEN
OK.
UP/DOWN 7. PRESS THE DOWN KEY TO
MENU KEY SELECT THE RADIO CHECK
BUTTON
THEN
4321 OK .
 FEATURES
HOW TO CALL ALERT A STATION
1. POWER ON
2. PASSWORD CLICK (4321 WITH
THE HELP OF KEY PAD )
3. PRESS MAIN MENU
4. GOTO CONTACT THEN PRESS
OK
POWER
ON 5. PRESS UP KEY TO SELECT THE
MANUAL DIAL THEN PRESS
OK.
6. TYPE THE RADIO ID WHICH
CALL
ALERT IS TO BE SENT THEN
OK
UP/DOWN 7. TO SELECT CALL ALERT
MENU KEY 8. PRESS OK BUTTON .
BUTTON

4321
 FEATURES
HOW TO CHECK GRID REFENCE
1. POWER ON
2. PASSWORD CLICK (4321 WITH
THE HELP OF KEY PAD )
3. PRESS MAIN MENU
4. PRESS DOWN KEY TO SELECT
THE
POWER
ON UTILITIES.
5 PRESS OK BUTTON
6. PRESS DOWN KEY TO SELECT
THE
RADION INFO .
7. PRESS DOWN KEY TO SELECT
THE GPS INFO
UP/DOWN 8. PRESS OK BUTTON
MENU KEY 9. ON DISPLAY
BUTTON LATITUDE/LONGITUDES
4321
Buttons
MOTOTRBO XiRP8668
• Frequency Range – 136 – 174 MHz
• Power - 1/5 W
• Channel – 1000, Spacing 12.5 KHz
• No. Of Group – 250
• No Of Zones-250
• No. Of Contacts - 1000
XiRP8668 -5W
• Sensitivity – 0.25 µV
• A/N Key Pad/Display
• 6 Programmable Buttons
MOTOTRBO XiRM8668
• Frequency Range – 136 – 174 MHz
• Power - 1-25 W
• Channel – 1000, Spacing 12.5 KHz
• No. Of Contacts - 1000
• Sensitivity – 0.25 µV
• A/N Key Pad/Display XiRM8668 -25W

• 4 Programmable Buttons
 Radio check
1. Check a destination radio whether is active or not

Contacts-OK

Manual Dial-OK- Select

particular radio id(user
802)

ok

Select radio check

ok
 Call alert
1. When a radio send a call alert in a particular radio following
2. instructions to keep

Contacts-OK

Manual Dial--OK--Select
particular radio id(user 802)

ok

Select Call alert

ok
 Send a missed call
1. When a radio send a missed call in a particular radio following instructions t

Contacts-ok

Manual Dial-Select
particular radio id(user 802)

press PTT button and

release
 Private call
1. If a radio wants to make a private call to a radio, can use this fa

Contacts-OK

Manual Dial-OK-Select
particular radio id(user 802)

ok

Select Call alert

ok
 Remote radio monitoring
1. If a radio wants to monitor the remote radio can use this facility
2. In this facility we can activate remote tranmitter without their permiss
3. This facility is programmable to who can access this.
4. Transmitter activate 10 sec to 2 min time duration as per instruction

Contacts-OK

Manual Dial-OK-Select
particular radio id(user 802)

ok

Select remote monitor

ok
 Radio Kill/Unkill
1. If a radio wants to kill/unkill (turn OFF/turn ON) the remote radio, can use this
2. In this facility we can kill/unkill remote radio without their permission
3. Remote radio can not turn on the radio when it killed

Contacts-OK Contacts-OK

Select particular Select particular

radio id(user 802) radio id(user 802)

ok ok

Select radio Select radio

disable enable

ok ok
GPS Info

Menu-

utilities

ok

Radio info

GPS info

Display shows
GPS information's
All Tones On / Off
Menu

Utilities-----OK

Radio Settings--OK

Tones & Alerts

All Tones

Disable or Enable
LED Indicator On \ Off

Menu

Utilities-----OK

Radio Settings--OK

LED Indicator

On or Off
 CPS Installation
Introduction
Please read the instructions below before proceeding with the installation
package for any of the MOTOTRBO Customer Programming Software (CPS)
Applications available on the DVD kit. Be sure to carefully read all on-
screen instructions during the installation.

System Installation Requirements

All computer systems installing the available MOTOTRBO CPS Applications
must adhere to the following minimum requirements:

Operating Systems: (for installing MOTOTRBO CPS with Radio

Management Server and Radio Management Device Programmer)
• Windows 8, Windows 8.1, 32-bit and 64-bit
• Windows 7 Ultimate/ Professional (SP 1 or higher) 32-bit and 64-bit
• Windows Server 2008 R2 SP1 32-bit and 64-bit

Mobile Communications (I) Pvt. Ltd., New Delhi

 CPS Installation Cont.
Recommended Hardware Requirements:
• Processor: 2 GHz dual core or higher Pentium grade
processor.
• Memory: 4 GB RAM.
• Aero capable graphics card with 128 MB graphics
memory.
• 50 GB free hard disk space on a 5400 RPM hard disk
drive.
• USB Port for radio communication
• DVD-ROM for software installation.
Note: This configuration is required when working with
large code plugs. You need to have Administrator rights
on the target computer in order to proceed with any of the
installations.

Mobile Communications (I) Pvt. Ltd., New Delhi

 CPS Installation Cont.
Customer Programming Software (CPS) Installation
Instructions

1. Unplug any devices that are connected to your computer.

2. Exit all the programs running on your computer.
3. Make sure that you are logged on as a user that has local
administration rights to your computer. You may enable UAC
instead.
4. Insert the DVD into your DVD drive. If you have more than one
DVD drive, use the master DVD drive.
5. Wait for the auto-install program to start and follow the
instructions on the screen. If the auto-install program fails,
navigate to Setup.exe on the DVD and double-click it.
6. On the first screen, you may see a language selection option
where you can pick the language that would be used for the rest of
the install.
7. If so, select a language and then click on the Next button to
proceed to the feature selection screen.
Mobile Communications (I) Pvt. Ltd., New Delhi
 CPS Installation Cont.

Mobile Communications (I) Pvt. Ltd., New Delhi

 CPS Installation Cont.
8. To install only the CPS, please check the box that says
MOTOTRBO Customer Programming Software.

Note: If installing any of the Radio

Management components, please
see Radio Management
Installation Instructions

Mobile Communications (I) Pvt. Ltd., New Delhi

 CPS Installation Cont.
9. Accept the License agreement whenever prompts.

Mobile Communications (I) Pvt. Ltd., New Delhi

 CPS Installation Cont.
10. Follow the instructions on the screen to complete the installation.
11. If security related messages come up during the install, Click 'OK' to
proceed.

Note: It is required to
reboot
the machine if asked
during
he install process.

Mobile Communications (I) Pvt. Ltd., New Delhi

Upgraded CPS Mototrbo File
1. Add Channel
2. Radio ID Programming
3. Group Call Programming in Digital Channel
4. Private Call Procedure
5. Facility of Locking Keypad
6. Scan With Priority:-
7. Transmitter Time Out Timer
8. Remote Kill /Stun/ Revive
9. Emergency
10.Messaging Procedure
11.Features Enable/Disable
12.Power Adjustment Base Radio
13.Power On Password
14.CPS Password
 Read Radio go to channels , Right click on zone 1--- go to
add—click on Analog Channel . Now click on channel. Select bandwidth 12.Khz\25
Khz ( must be select one, it will be same in all radios ). Put frequency in RX and TX
. Select Squelch type- CSQ in TX & RX
 Click on Analog Channel Channel and Put RX and TX
Frequency. Signaling system should Be MDC Sys 1 in TX and RX. Change admit
Criteria in Always.
Read Radio Go to General Settings (window will be displayed as shown
below) Put Radio Name and Radio ID (EX. Motorola 808 in Radio name
and 808 in Radio ID) Now Write the Radio . To program other radios and
change radio name and ID and clone the Radio

Contd…
Read radio. Got to Signaling Systems –Put Primary ID –XXXX, PTT ID Type-Post only, PTT
Side tone- none.
Now go to Analog Channel– Select MDC Sys1 in RX and TX Signaling System.
Read Radio Go to Contacts Select Digital and Right Click
Click on add
click on Group Call (following window will be displayed)
Rename Group name and Put Call ID (Should be same for the Entire
Group)
Click on RX group list Go to digital and Right Click Click
on Add and then click on RX Group List
Now Go to Channel Right click on Zone 1 than click on
ADD click Digital channel.
Now put frequency in RX and TX Select Group call in Group List
and Contact Name field. Now write the radio.
Now rename RX group list and select member for GROUP Call
Now put frequency in RX and TX Select Group call in Group List
and Contact Name field. Now write the radio.
Read Radio, Go to Buttons– Select any Button as keypad lock.
Read Radio, Go to Digital and Analog Channel--- Select Scan List 1
 Go to Scan --- List 1---, Now Select Channels in Member list and set any
channel as priority channel
Go to Digital or Analog Channel and click. Now Select Desire TOT which
is required. Default TOT is 60 sec. Min can be 15 sec , Max can be 495 Sec.
Read Radio – Go to Menu and enable Kill / Unkill Facility.
Now go to Signaling Systems– Tick Radio Disable Decode.
Go to Buttons --- Select Orange Button as Emergency on in in Long Press
Mode.
Go to Signaling Systems—Digital Emergency—Sys-1, Now Select Alarm type-
Regular, Mode—Emergency Alarm,--Revert Channel –Selected.
Go to Analog and Digital Channel– Select Sys-1 in Emergency Channel
Read Radio--- Go to Text Messages– You can save 50 Predefined SMS as short
and long messages. Message length maximum 138 character.
General settings—Front programming Passwords—Mode- Dealer, Password-Put
any 8 Digit Password which is use for manual programming without PC.
 Read Radio go to Text Messages Click on add
now insert any message . We can insert only 50 messages on that with
max 140 characters. Now write the radio.

Click
on Menu
Go to Message and OK now you will see Inbox, Write , Quick Text ,
Send Items, Draft. Now go to write option and write any message than
OK , send option will be displayed. Now press ok then go to manual
dial, type other radio ID (Ex. 202) than OK message will be go to Radio
202.
If we want to send message to all radio of a group, then select Group
name and send to all sets.
 Click on Menu Go to Contacts and ok
now go to manual dial and ok Type remote radio ID (ex . 202 )
and click on ok you will see call alert Select OK
A alert tone will be heard on other radio if other radio respond it
with PTT Private call will be established.

ID 201 ID 202

ID 204
ID 203
 If we want to enable all the features Ex. Call Alert, Private Call
, Radio Check , Radio Disable/Enable etc. options need to be enabled in
Menu. Read radio go to Menu and check the required options.
 If we want
change power in Repeater/Mobile, go to General Settings than go to TX
Low Power insert value than go to TX Hi Power insert required value.
Then Write the radio.
Remote radio monitoring
time setting
 DMO Mode (6.25e) Programming
With the help of DMO user can get 2 channel in a single simplex frequency.
Configuration—
Team Leader Preference---Preferred,
 DMO Mode (6.25e) Programming
Repeater Time Slot—1, in 1st Channel, 2 in Second Channel,
Pls Note:- Both Channels have same frequency.
 Master Radio Permissions
Its help to make a master radio killing the radio.
So that only authorize user can kill /Unkill the radio
AES 256 BIT ENCRYPTION
AES 256 BIT ENCRYPTION
 VHF DATA COMMUNICATION SETUP

Station - 2
Station - 1

Software :-Smart PTT file transfer (Client ) & Smart PTT File receiver (server)
 DATA COMMUNICATION WITH MOTOROLA
DIGITAL RADIO XIRM 8668
•Requirement:
➢Digital Radio sets with all accessories.
➢Data / Programming cable.
➢Computer/Laptop with windows operating
system and .net version 4.5

➢Software- SmartPTTfile transfer

•Connectivity: sets are connected with the computer

using programming lead at USB Port.
 DATA COMMUNICATION WITH MOTOROLA
DIGITAL RADIO XIRP/XIRM 8668

Introduction about software:-

Integrated solution for MOTO TRBO™
Smart PTT is a software application for development of
MOTO TRBO-based radio dispatch systems.
Smart ptt file transfer is a freeware (software).

File supported:- word, excel, power point, text, image (all

Types)
 DATA COMMUNICATION WITH MOTOROLA
Procedure:-
DIGITAL RADIO XIRP/XIRM 8668
➢ Connect the set as per hook up diagram
➢ Now install the Smart PTT file transfer software in both the
PC/Laptop
➢ Keep window fire wall disable if required.
➢ Now use Smart PTT-file transfer client to send the data by clicking -
Start->All programs-> Smart PTT File Transfer->Smart PTT file
transfer
client
➢ Now use Smart PTT-file transfer Server to receive the data by
clicking -
Start->All programs-> Smart PTT File Transfer->Smart PTT file
 METHODOLOGY
How to send the data?
Create the file to transfer
Select the file by clicking:-
File then Select file
 METHODOLOGY
➢ Now entre the radio id of the station which is receiving the file.
i.e. 3998 as in the screen shot.
.
➢ Now click on connect button as given in the screenshot
 METHODOLOGY
➢ When remote radio connected click on start file transfer button.
.
 METHODOLOGY
HOW TO RECEIVE THE DATA?

Run Smart .PTT file transfer client in the PC/laptop as mentioned above
Now click on setting-
 METHODOLOGY
A pop up window will get up as given
below:-

Now entre the location of folder in which you want to store

the incoming files.
 METHODOLOGY
HOW TO RECEIVE THE DATA?

Now click. on start server button and wait to receive the files
from clients.
 METHODOLOGY

➢ Now, all the files received will be

available in the target (eg- TRAIL)
.

folder
.
 OBSERVATIONS AND LIMITATIONS:-

➢ Time of the data transfer is irrespective of file format.

.
➢ Data transfer paused while voice communication is established.

➢ Transfer restarted after completion of voice communication.

.
➢ Time may vary if packets will lost.

➢ At initial stage, problem arise during connection between smart PTT

server and client.

➢ This is one way data communication. SERVER is used to receive and

CLIENT is used to send the data.

➢ Data communication doesn’t interfere voice channel. No any sound

noticed during data transmission / reception.
DIGITAL TRACKING
(With VHF handheld devices)
 EXISTING DATA COMMUNICATION SYSTEM

Station - 2
Station - 1

Software :-Smart PTT file transfer (Client ) & Smart PTT File receiver (server)
Equipements & assys
XIRM8668 DIGITAL WIRELESS SET ( FOR BASE STATION)

HOLE MOUNT GPS ANTENNA.

PROGRAMMING CABLE

LAPTOP / DESKTOP

HANDHELD RADIOS FOR REMOTE USERS

 GPS TRACKING SETUP
GPS programmed handheld radio sets for track

VHF ANTENNA

HOLE MOUNT ANTENNAA

Programming cable to connect labtop/desktop

DIGITAL RADIO SET FOR BASE STATION

Trans TRBO Software installed

Labtop/desktop
 ADDING RADIO STATION FOR TRACK
Enter the ID of the remote handheld

REMOTE USER POSITION INDICATOR

BASE STATION INDICATOR

TRACKING VIEW
 TRACKING VIEW

18.152542
81.512231
VOICE CALLING FROM LAPTOP/DESKTOP

Can talk with the remote station by

entering ID by the help of mouse
click without pressing PTT of the
radio handset
CALL HISTORY

Can store and recall of the

conversation history
 MESSAGING
Enter ID of the remote station for whom to send message

May enter the message by using the soft key pad displayed below

Can message from the

labtop/desktop to the remote user
set
CONFIGURATION OF IP ADDRESS

Trackig may also can watch from

distant by using the IP address/
internet after configuration.
PASSWORD PROTECTION

System can protect with password

to avoid misuse.
PASSWORD PROTECTION

System can protect with password

to avoid misuse.
 Digital tracking with VHF handheld device

❖Trans TRBO to be installed in labtop or desktop for

monitor
digital
❖By usingradio
free set
software of TransTRBO in Laptop/Desktop
easily can monitor the movements of remote handheld
digital sets users by GPS.
❖The Trans TRBO integrated GPS allows for indication of
remote users location and routes on map.
❖This feature is useful in case you need to know
location of handheld user by just click on the toolbar of
the
application.
❖Through-hole mount antenna that combines GPS and VHF
capabilities.
❖This antenna design provides GPS tracking coverage and
voice/data wireless \ capabilities for fleet monitoring or
 Digital tracking with VHF handheld device

❖ Easy to command
❖ Simple screen layout
❖ Designed for mouse
❖ Full screen or span multiple
monitors
❖ Call indicators for quick call
assessment
❖ Supports 5 levels of user access
❖ Radio Display simulator
 Digital tracking with VHF handheld device

❖ Comprehensive Help system .

❖ Comprehensive user List manipulation
❖ Individual Data Services configuration for
GPS poll server
❖ Simply can add, remove, save, load or reset of the
radio Poll list
❖ Google Maps(TM) displayed in a separate
scrollable panel with Zoom, Map Load plus
centering on points of interest
 ADVANTAGES

➢ The formation of troops movement with location of head

and tail can be seen.

➢ Whether troops are moving or static can be seen.

➢ Live monitoring of OPS and route being followed is

possible.

➢ Correction of formation, route, directing troops towards

a
specific target can be done

➢ In the case of ROP,RSO operations it can be ensured that

the troops are properly covering the entire length of the
road and no gaps are left out.
 DISADVANTAGES

➢ in case jungle there will be break in communication if

LOS
is not available

➢ VHF communication range with walky talkies sets in

limited to 5 kms in jungle terrain

➢ antenna height of wireless set at coy location has to be

increased to get better range and ensure communication
without any breaks during operations.