Product data sheet 6EP1333-2BA01
SITOP SMART 120 W STABILIZED POWER SUPPLY
INPUT: 120/230 V AC OUTPUT: 24 V DC/5 A PFC
VERSION
Technical specifications
Product SITOP smart
Power supply, type 24 V/5 A
Input
Input 1-phase AC
Supply voltage / 1 / at AC / nominal value 120 V
Supply voltage / 2 / at AC / nominal value 230 V
Voltage range
• Note Set by means of selector switch on the device
Input voltage / 1 / at AC 85 … 132 V
Input voltage / 2 / at AC 170 … 264 V
Wide-range input No
Overvoltage resistance 2.3 × Vin rated, 1.3 ms
Mains buffering at Iout rated, min. 20 ms
Mains buffering at Vin = 93/187 V
Rated line frequency 50 / 60 Hz
Rated line range 47 ... 63 Hz
Input current / at nominal level of the input voltage 120 V 2.1 A
Input current / at nominal level of the input voltage 230 V 1.15 A
Switch-on current limiting (+25 °C), max. 32 A
Duration of current limiting / at 25 °C / typical 3 ms
6EP1333-2BA01 subject to modifications
Page 1/ 4 12/30/2013 © Copyright Siemens AG 2013
I²t, max. 0.8 A²·s
Built-in incoming fuse T 3,15 A/250 V (not accessible)
Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: from 6 A characteristic C
Output
Output Controlled, isolated DC voltage
Rated voltage Vout DC 24 V
Total tolerance, static ± 3%
Static mains compensation, approx. 0.1 %
Static load balancing, approx. 0.5 %
Residual ripple peak-peak, max. 150 mV
Residual ripple peak-peak, typ. 50 mV
Spikes peak-peak, max. (bandwidth: 20 MHz) 240 mV
Spikes peak-peak, typ. (bandwidth: 20 MHz) 150 mV
Adjustment range 22.8 … 28 V
Product feature / output voltage adjustable Yes
Output voltage setting via potentiometer
Status display Green LED for 24 V OK
On/off behavior Overshoot of Vout approx. 4 %
Startup delay, max. 0.1 s
Voltage rise, typ. 50 ms
Rated current value Iout rated 5A
Current range 0…6A
• Note 6 A up to +45 °C
delivered active power / typ. 144 W
short-term overload current / at short-circuit during run-up / typical 17 A
Duration of overloading ability for excess current / on short-circuiting 100 ms
during the start-up
short-term overload current / at short-circuit during operation / typical 17 A
Duration of overloading ability for excess current / on short-circuiting 200 ms
during the operational phase
Parallel switching for enhanced performance Yes
Numbers of parallel switchable units for enhanced performance 2
Efficiency
Efficiency at Vout rated, Iout rated, approx. 87 %
Power loss at Vout rated, Iout rated, approx. 17 W
Closed-loop control
Dynamic mains compensation (Vin rated ±15 %), max. 0.3 %
Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. 1%
Load step setting time 50 to 100%, typ. 0.2 ms
Load step setting time 100 to 50%, typ. 0.2 ms
6EP1333-2BA01 subject to modifications
Page 2/ 4 12/30/2013 © Copyright Siemens AG 2013
Protection and monitoring
Output overvoltage protection < 33 V
Current limitation 6.4 … 6.6 A
Characteristic feature of the output / short-circuit protected Yes
Short-circuit protection Constant current characteristic
Enduring short circuit current / Effective level / typical 10 A
Overload/short-circuit indicator -
Safety
Primary/secondary isolation Yes
Potential separation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN
50178
Protection class Class I
stray current / maximum 3.5 mA
stray current / typical 0.4 mA
CE mark Yes
UL/CSA approval Yes
UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259,
cCSAus (CSA C22.2 No. 60950-1, UL 60950-1, UL 1604)
Explosion protection ATEX (EX) II 3G Ex nA II T4; UL 1604 Class I, Div. 2, Group ABCD
FM approval -
CB approval Yes
Marine approval GL
Degree of protection (EN 60529) IP20
EMC
Emitted interference EN 55022 Class B
Supply harmonics limitation EN 61000-3-2
Noise immunity EN 61000-6-2
Operating data
Ambient temperature / in operation 0 … 60 °C
• Note with natural convection
Ambient temperature / on transport -40 … +85 °C
Ambient temperature / in storage -40 … +85 °C
Humidity class according to EN 60721 Climate class 3K3, no condensation
Mechanics
Connection technology screw-type terminals
Connections / Supply input L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm² single-core/finely
stranded
Connections / Output L+, M: 2 screw terminals each for 0.5 ... 2.5 mm²
Connections / Auxiliary -
Width / of the housing 50 mm
6EP1333-2BA01 subject to modifications
Page 3/ 4 12/30/2013 © Copyright Siemens AG 2013
Height / of the housing 125 mm
Depth / of the housing 125 mm
Installation width 50 mm
Mounting height 225 mm
Weight, approx. 0.5 kg
Product feature / of the housing / housing for side-by-side mounting Yes
Type of mounting / wall mounting No
Type of mounting / standard rail mounting Yes
Type of mounting / S7-300 rail mounting No
Installation Snaps onto DIN rail EN 60715 35x7.5/15
Other information Specifications at rated input voltage and ambient temperature +25
°C (unless otherwise specified)
letzte Änderung: Dec 30, 2013
6EP1333-2BA01 subject to modifications
Page 4/ 4 12/30/2013 © Copyright Siemens AG 2013
