ORDER NO.

MTNC130213CE
B01 Canada: B61

LCD TV

Model No. TC-L32B6

TC-L32B6P

©Panasonic Corporation 2013.

Unauthorized copying and distribution is a
violation of law.
 CONTENTS

1. Safety precautions ................................................................................................. 3

2. Alignment instructions and method of software upgrading.....................................5

3. Working principle analysis of the unit ................................................................... 12

4. Specifications.......................................................................................................13

5. Block diagram ......................................................................................................14

6. Boards Layout......................................................................................................17

7. Wiring diagram ...................................................................................................18

8. Troubleshooting guide..........................................................................................22

9. Exploded View .....................................................................................................26

10. Replacement Parts List......................................................................................28

11. Disassembly and Assembly Instructions............................................................29

2
Attention: This service manual is only for service personnel to take reference with. Before servicing
please read the following points carefully.

Safety precautions
1. Instructions
Be sure to switch off the power supply before replacing or welding any components or
inserting/plugging in connection wire Anti static measures to be taken (throughout the entire production
process!):
a) Do not touch here and there by hand at will;
b) Be sure to use anti static electric iron;
c) It’s a must for the welder to wear anti static gloves.
Please refer to the detailed list before replacing components that have special safety requirements.
Do not change the specs and type at will.

2. Points for attention in servicing of LED

2.1 Screens are different from one model to another and therefore not interchangeable. Be sure to
Use the screen of the original model for replacement.
2.2 The operation voltage of LED screen is high voltage. Be sure to take proper measures in
protecting yourself and the machine when testing the system in the course of normal operation or
right after the power is switched off. Please do not touch the circuit or the metal part of the module
That is in operation mode. Relevant operation is possible only one minute after the power is switched
off.
2.3 Do not use any adapter that is not identical with the TV set. Otherwise it will cause fire or damage
to the set.
2.4 Never operate the set or do any installation work in bad environment such as wet bathroom,
laundry, kitchen, or nearby fire source, heating equipment and devices or exposure to sunlight etc.
Otherwise bad effect will result.
2.5 If any foreign substance such as water, liquid, metal slices or other matters happens to fall into the
module, be sure to cut the power off immediately and do not move anything on the module lest it should
cause fire or electric shock due to contact with the high voltage or short circuit.
2.6 Should there be smoke, abnormal smell or sound from the module, please shut the power off at
once. Likewise, if the screen is not working after the power is on or in the course of operation, the
power must be cut off immediately and no more operation is allowed under the same condition.
2.7 Do not pull out or plug in the connection wire when the module is in operation or just after the
power is off because in this case relatively high voltage still remains in the capacitor of the driving
circuit. Please wait at least one minute before the pulling out or plugging in the connection wire.
2.8 When operating or installing LED please don’t subject the LED components to bending, twisting or
extrusion, collision lest mishap should result.
2.9 As most of the circuitry in LED TV set is composed of CMOS integrated circuits, it’s necessary to
pay attention to anti statics. Before servicing LED TV make sure to take anti static measure and
ensure full grounding for all the parts that have to be grounded.
2.10 There are lots of connection wires between parts behind the LED screen. When servicing or
moving the set please take care not to touch or scratch them. Once they are damaged the screen
would be unable to work and no way to get it repaired.
If the connection wires, connections or components fixed by the thermo tropic glue need to disengage
when service, please soak the thermo tropic glue into the alcohol and then pull them out in case of
damage.

3
2.11 Special care must be taken in transporting or handling it. Exquisite shock vibration may lead to
breakage of screen glass or damage to driving circuit. Therefore it must be packed in a strong case
before the transportation or handling.
2.12 For the storage make sure to put it in a place where the environment can be controlled so as to
prevent the temperature and humidity from exceeding the limits as specified in the manual. For
prolonged storage, it is necessary to house it in an anti-moisture bag and put them altogether in one
place. The ambient conditions are tabulated as follows:

Temperature Scope for operation 0 ~ + 35 oC

Scope for storage -20 ~ + 60oC
Humidity Scope for operation 20% ~ 80 %
Scope for storage 10% ~ 90%

2.13 Display of a fixed picture for a long time may result in appearance of picture residue on the
screen, as commonly called “ghost shadow”. The extent of the residual picture varies with the maker
of LED screen. This phenomenon doesn’t represent failure. This “ghost shadow” may remain
in the picture for a period of time (several minutes). But when operating it please avoid displaying still
picture in high brightness for a long time.

3. Points for attention during installation

3.1 The front panel of LED screen is of glass. When installing it please make sure to put it in place.
3.2 For service or installation it’s necessary to use specified screw lest it should damage the screen.
3.3 Be sure to take anti dust measures. Any foreign substance that happens to fall down between the
screen and the glass will affect the receiving and viewing effect
3.4 When dismantling or mounting the protective partition plate that is used for anti vibration and
insulation please take care to keep it in intactness so as to avoid hidden trouble.
3.5 Be sure to protect the cabinet from damage or scratch during service, dismantling or mounting.

4
 2. Alignment instructions
(1) Test equipment
VG-859 (YPbPr, VGA, HDMI signal generator)
FLUKE 54200(TV signal generator)
CA310 (white balancer)
(2) Power test
Connect main board, power board and IR board according the wiring diagram, connect
the power and press power key (Remote controller or Keypad) button to turn on the TV.
a) Test the pin voltage of P802/power board , the data is shown in table1:

Table1 voltage data of P802

For 32”
P802 Pin1,2 Pin3,4 Pin5,6,7 Pin8,9 Pin10,11

Voltage GND 11.4V~12.6V GND 11.4V~12.6V 4.75V~5.25V

For 32”
Pin12 Pin13 Pin 14 Pin15 Pin16
On:2.5V~5.25V Normal: 2.0~5V On:2.5V~5.25V
Duty 5%~100% NC
Off: 0~0.5V Abnormal :0~0.5V Off: 0~0.5V

5
(3) Alignment flow-chart
The alignment flow-chart is shown as fig-1

Check if EDID, HDCP KEY, FLASH are written

Combined test for general assembly

Auto Gamma adjustment

Connect to the center signal source and check each

Function of TV (station leaking, analog control, etc.)
Check the output of speaker.

Input AV signal and check the function

Input HD signal and check the function of YPbPr

Input USB signal and check if the display is normal, check

the function (analog control), horizontal/vertical center, etc.

Input HDMI signal and check if the display is normal, check

the function (analog control), horizontal/vertical center, etc.
Checking SPDIF will output the signal on Amplifier.

Preset ex-factory

Check the accessories and packing

Fig-1 adjustment flow-chart

6
(4) Adjustment instruction

At any input source then press the “←”, “EXIT” and “OK” (using RC within 1 sec) to enter factory mode
During Factory menu, if “EXIT” key is pushed, system will exit factory mode.

4-1. Auto Gamma Adjustment & Check

4-2.1. Set into factory mode then choose Auto Gamma Adjust,
4-2.2. Press "2" "3" "2" "4" in turn within 1sec to enter the item, and push Init will self-generate gray pattern
for adjusting.

4-2.3. Following the Cool spec as bellow.

Color Cool
100IRE 0.2677
x
50IRE 0.2684
100IRE 0.2655
y
50IRE 0.2671

Adjust
±0.005
Tolerance

(1) Adjust 100IRE

First, Decrease G to meet y spec(0.2655).
Second, Decrease R to meet x spec(0.2677).
(2) Adjust 50IRE
First, Decrease G to meet y spec(0.2671).
Second, Decrease R to meet x spec(0.2684).
Note: Do not adjust the B GAIN on both 100IRE and 50IRE.
When match the spec, pressing “Save” then exit the adjustment page.

(5) When match the spec, pressing right key in "Save" position then exit the adjustment page.
4-2.4. Exit Factory Mode:
After finish Gamma adjust press [EXIT] to exit factory mode.

7
(5) Items of Factory menu
When in any source, press the “Left -> Exit -> Enter” key of remote control can enter into factory mode.
During Factory menu, only “EXIT” key is pushed, system will exit factory mode.
Press up and down key can move high light item from Model Change -> Color Temp. Adjust -> Auto Gamma
Adjust -> Timer Clear -> Preset Channel -> Full Power -> ADC Calibration -> Shipping reset -> Bypass Gamma ->
UART Enable -> I2C -> Boot Loader Upgrade -> V-Com Adjust -> SG Pattern.
Push “Enter” key can enter high light item function. (Press left and right can adjust value)
Display Model version, Release Date, firmware version and released date on the bottom.

1)Model ID
Press up or down key can select high light item function
Press enter or right key to enter the item.
It's only used for FW engineer.
2)Color Temp. Adjust
Press up or down key can select high light item function
Press enter or right key to enter the item.
It's only used for PQ engineer.
3)Auto Gamma Adjust
Press up or down key can select high light item function
Press enter or right key to enter the item.
It's only used for PQ engineer.
4)Timer Clear
Reset the timer which records hours of LED panel burn in
This item will have a check dialog “yes or no” to do or not.
- Time in factory mode: Time function shall be displayed automatically. Saving the total time of system
power on (LED turn on), and count the time automatically. The timer is continuous and saved (per 10
minutes) forever, unless it will be reset by doing “Timer Clear”.
5)Preset channel
Load preset channel for production line.
6)Full Power
This is for power consumption testing.
To measure the maximum power consumption of TV set, we adjust the value of following items to
maximum.
- Video: Contrast maximum value, Brightness maximum value, Backlight maximum value.
- Audio: Volume maximum value, Bass default value, Treble default value.
Press enter key to turn on Full Power and OSD stay display until press enter key to recover from Full
Power.

8
 7)ADC Calibration
ADC Calibration function is reserved for calibration by hand (PQ engineer only).
8)Shipping reset
Reset all settings of OSD menu to default value.
Reset settings: Channel table, Model table (H/V Position, Clock, Phase), Source dependent setting
(Contrast, Brightness etc.), Common setting (Volume, Language etc.), Parental Control (Rating,
Password etc), Closed Caption.
9)Bypass Gamma
For factory test value of gamma.
10)UART Enable
Enable to communicate with Auto-Alignment system.
11)I2C
Enable to communicate with Eeprom burn-in tool.
12)Boot Loader Upgrade
For firmware downgrade used.
13)V-Com Adjust
It's reserved for BMS function.
14)SG Pattern
Aging is for factory burn in and PTN ID provides each pattern for tester using.

(6) Performance check

6-1 TV function
Connect RF to the center signal source, enter Channel menu → auto tuning, check if there are channels be
skipped, check if the picture and speaker are normal.

6-2 AV terminals
Input Video signal, check if the picture and sound are normal.

6-3 YPbPr terminal

Input YUV signal (VG859 signal generator), separately input the YUV signals listed in table4 and check if the
display and sound are normal at any situation (power on, channel switch and format convert, etc.)

Table4 YUV signal format

SYNC PIXEL SYNC BACK

FREQ PERIOD Display
POLARITY CLOCK WIDTH PORCH

MODE
LINE(kHz) LINE (pixel) LINE (pixel) LINE (pixel) LINE (pixel)
LINE
FRAME FIELD (MHz) FRAME FRAME FRAME
FIELD
(Hz) (lines) (lines) (lines) (lines)

15.734 1716 Negitive 27 1440 124 114

59.94Hz 720x480i 59.94 525 Negitive 480 3 15
31,469 858 Negitive 27 720 62 60
59.94Hz 720x480P 59.94 525 Negitive 480 6 30
45 1650 Positive 74.25 1280 40 220
60Hz 1280x720P 60 750 Positive 720 5 20
33.75 2200 Positive 74.25 1920 44 148
60Hz 1920X1080i 60 1125 Positive 1080 5 15
67.5 2200 Positive 148.5 1920 44 148
60Hz 1920X1080P 60 1125 Positive 1080 5 36

9
6-4 HDMI terminal
Input HDMI signal (VG859 signal generator), separately input the signals listed in table6 and check the display and
sound (32 KHz, 44.1 KHz, 48 KHz) at any situation (power on, channel switch and format convert, etc.)

Table6 HDMI signal format

HDMI
1/2/
SYNC PIXEL SYNC BACK
DVI FREQ FREQ PERIOD Display
Timing POLARITY CLOCK WIDTH PORCH
Table

LINE (pixel) LINE (pixel) LINE (pixel)

LINE(kHz) LINE (pixel) LINE
MODE (MHz) FRAME FRAME FRAME
FRAME(Hz) FIELD(lines) FIELD
(lines) (lines) (lines)

31.47 800 Negitive 25.175 640 96 48

640x480 59.94 525 Negitive 480 2 33
37.88 1056 Positive 40 800 128 88
800x600 60.32 628 Positive 600 4 23
48.36 1344 Negitive 65 1024 136 160
1024x768 60 806 Negitive 768 6 29
47.4 1440 Positive 68.25 1280 32 80
1280x768 (1280cvt) 59.99 790 Negitive 768 7 12
47.78 1664 Negitive 79.5 1280 128 192
1280x768 59.87 798 Positive 768 7 20
63.98 1688 Positive 108 1280 112 248
1280x1024 60.02 1066 Positive 1024 3 38
47.71 1792 Positive 85.5 1360 112 256
1360x768 60.02 795 Positive 768 6 18
47.71 1792 Positive 85.5 1366 112 256
1366x768 59.79 795 Positive 768 6 18
67.5 2200 Positive 148.5 1920 44 148
1920x1080 60 1125 Positive 1080 5 36
15.73 1716 Negitive 27 1440 124 114
59.94Hz 1440x480i 59.94 262.5 Negitive 480 3 15
31.47 858 Negitive 27 720 62 60
59.94Hz 720x480P 59.94 525 Negitive 480 6 30
45 1650 Positive 74.25 1280 40 220
60Hz 1280x720P 60 750 Positive 720 5 20
33.75 2200 Positive 74.25 1920 44 148
60Hz 1920X1080i 60 562.5 Positive 1080 5 15
27 2750 Positive 74.25 1920 44 148
24Hz 1920x1080P 24 1125 Positive 1080 5 36
33.75 2200 Positive 74.25 1920 44 148
30Hz 1920x1080P 30 1125 Positive 1080 5 36
67.5 2200 Positive 148.5 1920 44 148
60Hz 1920X1080P 60 1125 Positive 1080 5 36

10
 6-5 other functions check
a) Check the sleep timer, picture/sound mode, OSD, stereo and analog TV Teletext, etc.

(7) Firmware update process

(1) Plug the USB with the firmware file named upgrade_2013_NA.pkg
(2) If system detect upgrade_2013_NA.pkg, USB upgrade message would appear automatically.
(3) Press Up key to select Yes, and then press OK key to start the upgrading.

(4) Upgrading is starting, please wait for the progress finish.

(5) When the progress completed, please follow the instruction to remove USB and restart Power off
then on.

11
Working principle analysis of the unit
1. NTSC signals flow:
Antenna signal will be send to tuner TDST-H021F, t h e n T u n e r w i l l b e demodulating and
output standard video signal TV-CVBS, and sound SIF signal.
TV-CVBS will send to the master control IC MT5385 to video decode, de-interlace and scaler, then
output LVDS level drive for panel display.
The sound IF (SIF) will be fed into MT5385, after demodulating, pre-amplifying, bass adjusting and
volume control, the sound signal w i l l b e t r a n s f o r m i n t o d i g i t a l I 2 S s i g n a l and sent to
digital amplifier TAS5707.

2. Composite/Component signal flow

Composite signal and Component signal will be fed to MT5385 to perform video decode, de-
interlace and scaler, then output LVDS drive level for panel display.
Audio signal from Composite/Component terminal via matched resistance is fed to MT5385 to bass
adjust and volume control, the sound signal will b e t r a n s f o r m i n t o d i g i t a l I 2 S s i g n a l and sent
to digital amplifier TAS5707.

3. HDMI signal flow

Two HDMI video signals are directly fed to the master control IC MT5385 to digital decode, image
scale, then output LVDS drive level for panel display. HDMI audio signal via decoder built-in MT5385 to
bass adjust and volume control, the sound signal will b e t r a n s f o r m i n t o d i g i t a l I 2 S s i g n a l and
sent to digital amplifier TAS5707.

4. USB signal flow

USB signal via USB connector sent to MT5385 and its A/D conversion to YPbPr output for
MT5385, then output R/G/B of 24 bit to back end module to Video decode, de-interlace and
image scale, then send to LVDS level drive for panel display.
Sound signal of USB signal v i a matched resistance a n d sent to MT5385 to bass adjust and
volume control, the sound signal will b e t r a n s f o r m i n t o d i g i t a l I 2 S s i g n a l and sent to digital
amplifier TAS5707.
5. SPDIF signal flow
The master control IC MT5385 will transfer digital sound signal out by format Dobly Digital or PCM.

12
4. Specifications

13
 SPD32T 32” Block Diagram
5-1 Block Diagram
EE:
A70 60Hz Models by WXGA :2x10
MTK MT5835 Platform Full-HD :2x20
Panel out
R_out

Audio
AMP
TAS5707
L_out

DDR3 1G-1600
H5TQ1G63DFR-PBC

Audio I2S output

Flash 16MB DTV system IC
MX25L12845EMI-10G

MTK

MT5385 Keypad
EEPROM 64KB
IF +/- 24C32

CVBS/Y Pb Pr Crystal
& Audio R/L 27MHz IR

Enable

ARC
Buffer IR / LED-R
Board
Y

Pb
S/PDIF
Pr USB
Tuner
LG L
TDST-
H021F
R

ANT / COLOR STREAM HD

CABLE & COMPOSITE IN SPDIF HDMI 1 HDMI 2
& Audio R/L in OUT

14
Power board:FSP

15
Power board:DARFON

16
6. Boards Layout

11

Ref No. Board Name Function Remrks

1 PCBA IR/B Remote Receiver, LED All boards are non servicable
2 FIRMWARE M/B Main Board, Audio & Video Signal Processing and should be exchanged for
11 PWR MODU Power (AD/DC), DC-DC, Control Button service

17
 SPD32T 32-inch Wiring Diagram
7-1 BLOCK

18
7-2 Wiring Connection
AUO panel
Main board to Panel Main board to Speaker
SPD32T SPD32T
DC02L00700I DC02A00130I
280 mm L:280 & R:480 mm
Panel side Main board CN1 Main board CN4 Speaker
FI-X30SSL-HF LVDS cable JWT A2006WR0-2X10P JWT A2001WR2-4P Color Right
1 VCC Red 1 LVDS_PWR 1 SPK_OUTL+ Red P3 Speaker +
2 VCC Red 2 LVDS_PWR 2 SPK_OUTL- Black P2 Speaker -
3 VCC NC Left
4 VCC NC 3 SPK_OUTR- Green P5 Speaker -
5 GND NC 4 SPK_OUTR+ White P4 Speaker +
6 GND NC
7 GND NC
8 GND NC Main board to IR board/ Key
9 SELLVDS Yellow 8 LVVDS_SEL SPD32T
10 NC NC DC02V04140I
11 GND NC IR:450 mm & Key:750mm
12 RX0- Yellow 20 LVDS_D0O_N IR board CN1 Main board CN3
13 RX0+ White 19 LVDS_D0O_P JWT A2001WR2-11P Color JWT A2001WR2-5P
14 GND NC 1 VCC3V3_STB Red 1 VCC5_0_STB
15 RX1- Red 18 LVDS_D1O_N 2 IRR White 2 IRR
16 RX1+ White 17 LVDS_D1O_P 3 GND Black 3 GND

19
17 GND Black 5 GND 4 LED_G Orange 4 LEDG
18 RX2- Orange 16 LVDS_D2O_N NC 5 LEDR
19 RX2+ White 15 LVDS_D2O_P NC 6 Light_S_C
20 GND Black 6 GND NC 7 Light_S_D
21 RXCLK- Brown 14 LVDS_CO_N 1 GND Black 8 GND
22 RXCLK+ White 13 LVDS_CO_P 2 Power Red 9 Power Key
23 GND Black 7 GND 3 SAR0 Orange 10 SAR0
24 RX3- Black 12 LVDS_D03_N 4 SAR1 Yellow 11 SAR1
25 RX3+ White 11 LVDS_D03_P
26 GND NC
27 NC NC
28 NC NC
29 NC NC
30 GND NC

20
Main board to Power board:

21
8. Trouble shooting
1. Fault clearance
Before calling your dealer or service center for assistance, check the matters below once again.
(1) Make sure you have connected LED TV to your equipment as described in the section
“ CONNECTING LED TV”.
(2) Check cable connection. Verify that all external equipment and power cord are properly
connected.
(3) Verify that all power is switched on.
(4) If LED TV still does not produce an image, re-start the external equipment.
(5) If the image still does not appear, unplug LED TV from the external equipment and check the
external equipment. The problem may be with your graphics controller rather than with LED TV.
(When you reconnect LED TV, remember to turn the external equipment and TV off before you
power up LED TV. Power the equipment back on in order of LED TV and external equipment.)
(6) If the problem still exists, check the following chart.

Problem Try these Solutions

NO POWER
Plug this LED TV into the AC outlet.

Press POWER button on side control or on Remote Control to turn on LED TV.

Check POWER Indicator. If this indicator blank, this TV has getting trouble.
Remote
Check the batteries.
Control does
Make sure nothing is between the Remote Receiver and the Remote Control.
not work
Make sure you are not too far from LED TV when using Remote Control.

Maximum operating range is 5m.

Is direct sunlight or strong artificial light shining on LED TV‘s Infrared Remote
Receiver? Eliminate the light by closing curtains, pointing the light in a different
direction, etc.
No image
Check the connection between the external equipment and LED TV.

When turning LED TV on, it takes within 7 seconds (ATV mode) to display the
image.

Check the system that you select is corresponding with the external equipment
or the video equipment.

Make sure the temperature is not out of the Operating Temperature (0°C ~
40°C).

Turn off power, then turn on again, re-start LED TV.
No sound
Check Audio cable connection from Audio input source.

Adjust the Sound System.

Press VOLUME (+) button.

Press MUTE button.
There are tiny
Dark or bright points of light (red, green, or blue) may appear on the screen.
black points This is a characteristic of the LED panel, not a malfunction of the LED TV.
and/or bright
LED panel is produced with very high accuracy technology. There is 99.99% or
more dot pixel, but there is also 0.01 % or less of dot pixel lack or dot pixel that
point on the TV
is constantly lighted. This is not defect.

Regarding LED panel characteristic, it may occur picture remain (look like a
mirror) when the screen is changed if it displays same screen for a long time.
Changing the picture or turn-off the power supply may recover.

Stripe pattern (more, interference stripes) may show up on the screen depends
on the reflected picture.
Abnormal
Adjust the value of color.
color of image
Select different color system.
22
 2. Troubleshooting guide
The flow chart shown below will help you to troubleshoot your Televison set with it doesn’t display
normally. Each procedure offers a simple way to check for system errors. Before starting, ensure
that there is a signal in and that the Televison is turned on.

2-1 Power LED no light

23
2-2 Has audio but no video out

2-3 Has video but no audio out step 1

24
2-4 Has video but no audio out step 2

25
9. Exploded View
12
03
17

17

16
04
21 29 23 26 20
02
15 19
18
27
13
06
01 10
07
05
17 08 28
09

14
21 25
29 10
04 28 29
24 18
27 20
11
28
22 30
29
30
 36

37 31
40

POP label
41

34

38

33

39 Type A

44
35
45 32
Type B
42

43
 10. Replacement Parts List
Note: All parts aresupplied by PAVCA.

Safety Ref.No. Part No. Part Name & Description Pcs Remarks
1 TZZ00000766A PCBA IR/B 1
2 TZZ00000767A FIRMWARE M/B 1 TC-L32B6
2 TZZ00000768A FIRMWARE M/B 1 TC-L32B6P
3 TZZ00000772A LCD MODU 1
4 TZZ00000780A SPK SET(90d)(PIN90d) 2
5 TZZ00000781A H-CON SET 1
6 TZZ00000782A H-CON SET 1
7 TZZ00000783A H-CON SET 1
8 TZZ00000784A H-CON SET 1
9 TZZ00000786A H-CON SET 1
10 TZZ00000079A MYLAR AL TAPE 2
11 TZZ00000844A PWR MODU(SPD32T) 28 1
12 TZZ00000774A CABINET ASSY 1
13 TZZ00000775A BACK COVER ASSY 1
14 TZZ00000787A METAL VERTICAL-L 1
15 TZZ00000788A METAL VERTICAL-R 1
16 TZZ00000789A METAL CH FRAME-A 1
17 TZZ00000790A LCD MTG SIDE(32B6) 6
18 TZZ00000794A GROND SPRING (32B6) 2
19 TZZ00000804A SIDE AV BRACKET(32B6) 1
20 TZZ00000805A CH MOUNT BOSS(32B6) 2
21 TZZ00000806A SPEAKER BRACKET(32B6) 4
22 TZZ00000809A KEY BUTTON BRACKET(32B6) 1
23 TZZ00000078A LOCKING CABLE TIE 1
24 TZZ00000832A SUPPORT(32B6) 3
25 TZZ00000834A SCREW 3
26 TZZ00000835A SCREW 3
27 TZZ00000083A SCREW+LOCK WASHER(8) 4
28 TZZ00000838A SCREW(NL) 7
29 TZZ00000843A TAPPING SCREW 10
30 TZZ00000656A TAPPING SCREW 6
31 TZZ00000796A RATING NP-TC-L32B6 1 Model Name Plate TC-L32B6
31 TZZ00000799A RATING NP-TC-L32B6P 1 Model Name Plate TC-L32B6P
32 TZZ00000821A CARTON-TC-L32B6 1 TC-L32B6
32 TZZ00000824A CARTON-TC-L32B6P 1 TC-L32B6P
33 TZZ00000828A ENERGY GUIDE-TC-L32B6 1
34 TZZ00000831A PE BAG FOR TV 1
35 TZZ00000846A MANUAL KITS-32B6 1 TC-L32B6
35 TZZ00000848A MANUAL KITS-32B6P 1 TC-L32B6P
36 TZZ00000819A PWR CORD(S) 1 TC-L32B6
36 TZZ00000820A PWR CORD(S) 1 TC-L32B6P
37 N2QAYB000820 REMO CTRL AA 1
38 TZZ00000776A PEDESTAL ASSY 1
39 TZZ00000803A STAND MOLD 1
40 TZZ00000811A EPS FOAM(T-L) 1
41 TZZ00000812A EPS FOAM(T-R) 1
42 TZZ00000813A EPS FOAM(B-L) 1
43 TZZ00000814A EPS FOAM(B-R) 1
44 TZZ00000842A TAPPING SCREW 4 Type A screw
45 TZZ00000840A SCREW+2WASHER(10) 4 Type B screw

28
11 Disassembly and Assembly Instructions
11.1. Base cover + stand mold
1. Lay down the unit so that the rear cover faces upward.

2. Remove the 4 screws.

3. Remove the Base cover + stand mold

11.2. Back cover

1. Remove the total 19 screws.

2. Remove the back cover.

11.3. P-Board
1. Remove the 2 screws.

2. Disconnect the connectors (P1, P2, P3).

3. Remove the P-Board.

4. Remove the key button bracket

11.4. M-Board
1. Remove the 2 screws.

2. Disconnect the connectors (M1, M2, M3, M4).

3. Remove the M-Board.

4.Remove the side AV bracket

5. Remove the CH-mount boss

11.5. Speaker unit
1. Remove the 4 screws.

2. Remove the speaker units.

3. Remove the speaker bracket.

11.6. IR-Board
1. Disconnect the connectors (I1).

2. Remove the IR-Board.

11.7. Metal parts I
1. Remove the 6 screws.

2. Remove the metal parts (M1,M2, M3,M4).

11.8. Panel
1. Remove the Panel.