PIR Sensor Switch For Ceiling With Remote Control PIR Sensor Switch For Ceiling With Remote

PIR Sensor Switch For Ceiling With Remote Control

FUNCTION
Ф4.5"
You can manually adjust the time setting, Sensitivity and light-control (For detail: OPERATION); it is very easy to use.Install
Sensor at 2.5~3.5m position on the wall/ceiling (For detail: INSTALLATION INSTRUCTION) and connect the wire according

2.16"
to the WIRING DIAGRAMS. Switch on power, after about 20 seconds the unit enter stable working state. Here please turn
TIME knob to the position close to minimum, and turn LUX to sun for testing. When it senses. the controlled lamp will be
turned on and off regularly. If the above tests go through, then select the time, light-control and sensitivity to your
need. So its installation is ok.

OPERATION

SETTING BY REMOTE CONTROL

INTRODUCTION
BUTTON DESCRIPTION BUTTON DESCRIPTION
The product is a new Energy-saving switch, it adopts good sensitivity detector, integrated circuit and SMT. Press the ON/
OFF button, the light goes
Press AUTO button, the sensor starts to
It gathers automatism , convenient safe, Energy-saving and practical functions. It utilizes the infrared energy to permanent on or permanent off
ON/ function and all settings remain the same
OFF
mode, and the sensor is disabled. AUTO as the latest status before the light is
from human as control-signal source, it can start the load at once when one enters detection field.It is easy (MUST press AUTO button to quit this
switched on/off.
to install and used widely ,possessing the function of power show and detection show. mode for Setting.

Display the current/lastest setting The button TEST

2s is for testing purpose
parameters in LED indicators(the sensitivity only. after you choose sensitivity
DISP LED indicators will on for showing thresholds, then you press TEST2s button,
the setting parameters). TEST The sensor goes to test mode(hold time is
SPECIFICATIONS Press RESET button, all settings go
2s only 2s) automatically ,meanwhile the
stand-by period and daylight sensor are
RESET back to settings of dip Switch in disabled. Press AUTO button to quit from
Power source: 120-277VAC Sensor: PIR sensor. this mode.
Power frequency: 50/60Hz Time setting:10sec.~30min. (adjustable) 10 30 50
DAYLIGHT
SENSOR Enter in the setting condition, the
Wire Designation: Hot,Load,Neutral
100 300 500

Detection range: 3~10m (radii.) (adjustable) parameter leds of remote control will Navigate to LEFT and RIGHT for
Rated load: Load Requirements (each relay) flash to be selected. and Navigate to choose selected parameters in
Light-control: 10LUX~2000LUX (adjustable)
UP and Down for choose selected LED indicators.
@ 120VAC, 50/60Hz . ... .0-800W ballast or tungsten Detection angle: 360°(ceiling installation) parameters in LED indicators.
@ 220VAC,50/60HZ. .. . . .0-1000W ballast Installation height: 2.5~3.5m
Working temperature: -10C°~+40C° Confirm the selected parameters
@ 277VAC, 50/60Hz . ... .0-1200W ballast MODE1 MODE2 MODE3 MODE4
OK selected parameters in remote
Detection motion speed: 0.6~1.5m/s control. Press or , Enter in the setting
@ 347VAC, 50/60Hz . ... .0-1500W ballast
Standby power: working 0.45W (static 0.1W) Press SEND button, upload the
condition, the parameter leds of
@ 120VAC ....... .. . . ..1/6 hp current parameters to sensor(s), remote control will flash to be selected,
SEND the led light which the sensor Press for open or close smart day
connects will on/off as confirm. sensor that turn off/on light
automatically according to the change
SENSOR´S LED: MODE1 MODE2 4 Scene modes with preset of natural light level.
parameters which are available to
1. It always light after switch on power, and be off after the unit enter working state. be changed and saved in modes.
MODE3 MODE4
2. It flash once when the unit receives sensing signal.

INDUCTION RANGE
SETTING BY KNOB
360

10m 3m 3m 10m
2.5~3.5m

3 X Detector
Height of installation2.5~3.5m Detection range Detection angle

+
SENS LUX PUSH BUTTON

-1- -2-
 PIR Sensor Switch For Ceiling With Remote Control PIR Sensor Switch For Ceiling With Remote Control

① SENS: Adjust detection range. Turn clockwise to increase it and turn anti-clockwise to decrease it. It is 3m ROUND FIXTURE BOX WIREMOLD FIXTURE BOX MUD RING WITH BOX

when turn to mini, and it is 10m when turn to max.

② TIME: Adjust time setting of load work. Turn clockwise to increase it and turn anti-clockwise to decrease it.
The time setting is about 30min when turn to max. It is in impulse mode when turn to mini. If you want to
change impulse mode into short time mode, please turn a little anti-clockwise, later LED will blink three
times.
③ LUX: Adjust working light. Turn clockwise to increase it and turn anti-clockwise to decrease it. When turn
to mini, it will only work below the light-control about 10LUX, when turn to max, it can work any light-control,
Push button: Can turn on/off the connected load; Can also turn on/off microphonics.
To turn on/off the load connected: Just need to press the button and release soon.
To open/off the microphonics: press and wait until the LED flashes rapidly, then release the button.
Note: Microphonics is closed when we connect the sensor to power at the first time.
SOME PROBLEMS AND SOLUTIONS
The load doesn’t work:
a. Please check the power and load connect is correct.
NOTE:Remote controller and the knob setting priority are subject to the last setting.If the last b. Check if the load is good.
setting is remote controller,then all the settings are subject to the remote controller setting.Otherwise, c. Check if the show lamp accelerates its speed after detecting.
d. Check if the working light corresponds to the ambient light.
all the settings are according to knob setting.
The sensitivity is poor:
a. Please check if there is hinder in front of the detection window to effect receiving the signals.
b. Please check if the ambient temperature is too high.
WIRING DIAGRAMS c. Please check if the signals source is in the detection fields.
Hot (Black) d. Please check if the installation height corresponds to the height showed in the instruction.
e. Please check if the moving orientation is correct.
Black
The sensor can’t shut the load automatically:
a. Check if there are continual signals in the detection fields.
Power
Red b. Check if the time delay is set to the longest.
Black
c. Check if the power corresponds to the instruction.
Sensor d. Check if the temperature change obviously nears the sensor, such as air condition or
load central heating etc.
White
White
Neutral(White)

INSTALLATION INSTRUCTION

The Ceiling Mount sensor enclosure has Two self tapping screws provided with low
mounting holes that are slotted to line up with a voltage sensors for mounting directly to a
standard round fixture or single gang handy box ceiling tile or a metallic grid.
(screws not provided).

-3- -4-