4 3 2 1

PROCEDURE FOR PREPARING LIFT TO BE PROGRAMMED.

"PROGRAMMING MODE" INDIACOTR LED
1. Operate lift in "Screen mode" until lift is assembled and upper and down (maintenance)
limits are set. When power is first applied to the control the LED on the circuit board will
SHORT FIRST TWO PINS TO PUT CONTROL INTO "PROGRAMMING MODE"
indicate "Screen Mode" with four blinks, two short blinks, a long blink and then a short blink.
RD WH 2. Run lift to the upper limit before putting control into "Lift Mode"
3. Perform "Procedure for putting control into Lift Mode".
P

PROCEDURE FOR PUTTING CONTROL INTO "LFIT MODE":

B B
1. Remove the control to allow access to the programming pins on the circuit board of the control.
2. Short the first two pins on circuit board of the control to get control into "Programming Mode".
EYE AUX LED on circuit board should come on red and stay on for 10 seconds.
3. While LED is lit push the Key Up toggle switch.
LED will go off and then blink once and stay off indicating it is in "Lift Mode". When power is
first applied to the control the LED on the circuit board will indicate "Lift Mode" with four blinks,
two short blinks and then two long blinks. (V6B - one long, one short, two long)
4. Perform "Procedure for setting show position".

PROCEDURE FOR SETTING SHOW POSITION:

1. Use wall switch up and down buttons to get lift into desired show position.
2. While lift is at desired show position, press and hold the Key Down toggle switch
until lift begins to move upward. Lift will begin a calibration cycle where it will move
upward for two seconds, stop then move down for one second and then the Lift will
return to the desired show position.

PROCEDURE FOR RESETTING SHOW POSITION:

1. Move lift to the show position.
2. While lift is at the show position press and hold the Key Up toggle switch and release
NOTE: The control can be reset by switching the control between "Lift and Screen Modes". once the Lift begins moving upward.
3. The show position is now reset and ready for a new show position to be set.
A PROCEDURE FOR PUTTING CONTROL INTO "SCREEN MODE": A
WARNING: The lift should not be operated in the screen mode with the encoder connected to the control.
Irratic and unpredictabel movement may occur causing a safety hazard.
1. Diconnect the connector to the encoder. Note the wire color positions before disconnecting the encoder. DESIGNED BY: senochs 8/9/2004 DRAPER, INC.
TOLERANCES 411 S. PEARL STREET
2. Remove the control to allow access to the programming pins on the circuit board of the control. UNLESS NOTED DRAWN BY: senochs 5/9/2011 SPICELAND, INDIANA 47385-0425
3. Short the first two pins on circuit board of the control to get control into "Programming Mode". 2 PLC. DECIMAL: .01" CHECKED BY:
www.draperinc.com
The LED on the circuit board should come on red and stay on for 10 seconds. 3 PLC. DECIMAL: .005" TITLE:
ANGULAR: 1 MFG APPD BY: ENCODER CONTROL CALIBRATION GUIDE
4. While LED is lit push the Wall Switch up button. FRACTIONAL: 1/32"
LED will go off indicating it is in "Screen Mode". When power is ENG APPD BY:
MATERIAL:
first applied to the control the LED on the circuit board will indicate "Screen Mode" with four PROPRIETARY DRAWING NOTICE: THIS DOCUMENT CONTAINS CONFIDENTIAL,
blinks, two short blinks, a long blink and then a short blink. PROPRIETARY INFORMATION OF DRAPER, INC., IS THE PROPERTY OF DRAPER,
INC., AND MUST BE RETURNED UPON REQUEST. NEITHER RECEIPT NOR PAPER SIZE: FINISH:
5. Reconnect the encoder only after the control is switched back into "Lift Mode" POSSESSION THEREOF CONFERS ANY RIGHT TO OWN, REPRODUCE, USE, OR B
DISCLOSE IN WHOLE OR IN PART, ANY SUCH INFORMATION WITHOUT WRITTEN SCALE: REV: SHEET: 1 DWG NO. - PART NO.
AUTHORIZATION FROM DRAPER, INC. C OF: 1 SL & SLX SCISSOR LIFTS
4 3 2 1