ELEVATOR DRIVE CONFIGURATION SHEET
Function Code Parameter Name Set Value Default Setting
Group F0: Basic parameters
F0-00 Control mode 1: Closed-loop vector control 1
Command source
F0-01 1: Distance control 1
selection
Running speed under
F0-02 operational panel 0.05 0.05
control
F0-03 Maximum running speed 0.55 1.6
F0-04 Rated elevator speed 0.55 1.6
F0-05 Rated elevator load 500 1000
F0-06 Maximum frequency 50 50
Group F1: Motor parameters
F1-00 Encoder type 2: ABZ incremental encoder 0
F1-01 Rated motor power 5.3 Model dependent
F1-02 Rated motor voltage 380 Model dependent
F1-03 Rated motor current 12.1 Model dependent
F1-04 Rated motor frequency 25.5 Model dependent
F1-05 Rated motor speed 96 Model dependent
F1-25 Motor type 1: Synchronous motor 1
Group F2: Vector control parameters
Speed loop proportional
F2-00 15 40
gain Kp1
Speed loop integral time
F2-01 0.6 0.6
Ti1
Speed loop proportional
F2-03 35 35
gain Kp2
Speed loop integral time
F2-04 0.8 0.8
Ti2
Torque acceleration
F2-16 1 1
time
Torque deceleration
F2-17 350 350
time
Group F3: Running control parameters
F3-02 Acceleration rate 0.6 0.6
Acceleration start jerk
F3-03 2.5 2.5
time
Acceleration end jerk
F3-04 2.5 2.5
time
F3-05 Deceleration rate 0.6 0.6
F3-06 Deceleration end jerk 2.5 2.5
F3-07 Deceleration start jerk 2.5 2.5
Group F5: Terminal function parameters
F5-01 X1 function selection 33: Up leveling signal NC 33 NC
F5-02 X2 function selection 00: Invalid 35 NC
F5-03 X3 function selection 34: Down leveling signal NC 34 Nc
F5-04 X4 function selection 04: Safety circuit feedback N0 4 NO
F5-05 X5 function selection 00: Invalid 5 NO
F5-06 X6 function selection 38: Run contactor feedback NC 38 NC
F5-07 X7 function selection 39: Brake contactor feedback NC 39 NC
22: Shorting door lock circuit
F5-08 X8 function selection 22 NO
contactor feedback NO
F5-09 X9 function selection 40: Inspection signal NC 40 NC
F5-10 X10 function selection 09: Inspection up signal NO 09 NO
F5-11 X11 function selection 10: Inspection down signal NO 10 NO
F5-12 X12 function selection 44: Up limit signal NC 44 NC
F5-13 X13 function selection 45: Down limit signal NC 45 NC
F5-14 X14 function selection 48:Up slow-down 1 signal NC 48 NC
F5-15 X15 function selection 49: Down slow-down 1 signal NC 49 NC
F5-16 X16 function selection 00: Invalid 50 NC
F5-17 X17 function selection 00: Invalid 51 NC
F5-18 X18 function selection 00: Invalid 0
F5-19 X19 function selection 00: Invalid 0
F5-20 X20 function selection 43: Fire emergency signal NC 0
F5-21 X21 function selection 00: Invalid 0
F5-22 X22 function selection 00: Invalid 0
F5-23 X23 function selection 28: Elevator lock signal NO 0
F5-24 X24 function selection 00: Invalid 0
F5-25 CTB input type 1856 320
F5-26 Y1 function selection 01: Run contactor control 1
F5-27 Y2 function selection 02: Brake contactor control 2
03: Shorting door lock circuit
F5-28 Y3 function selection 3
contactor control
F5-29 Y4 function selection 00: Invalid
F5-30 Y5 function selection 00: Invalid
F5-31 Y6 function selection 00: Invalid
F5-37 X25 function selection 4: Safety circuit signal 0
F5-38 X26 function selection 5: Door lock circuit signal 0
F5-39 X27 function selection 0: Invalid 0
Group F6: Basic elevator parameters
F6-00 Top floor of the elevator 4 9
Bottom floor of the
F6-01 1 1
elevator
F6-02 Parking floor 2 1
F6-03 Fire emergency floor 2 1
F6-04 Elevator lock floor 2 1
F6-38 Elevator lock start time 18:30 00:00
F6-39 Elevator lock end time 7:00 00:00
Program control
F6-40 Set Bit5 to 1: Timed elevator lock 0
selection 1
Program control Set Bit10 to 1: Elevator lock in the
F6-41 0
selection 2 attendant state
Fire emergency function
F6-44 49224 16456
selection
Group F8: Enhanced function parameters
F8-01 Pre-torque selection 0: Pre-torque invalid 0
F8-03 Drive gain 0.6 0.6
F8-04 Brake gain 0.6 0.6
F8-11 Brake apply delay 0.6 0.6
Group F9: Time parameters
Idle time before
F9-00 10 10
returning to base floor
Time for fan and lamp to
F9-01 2 2
be turned off
F9-03 Clock : year 2023 Current year
F9-04 Clock : month 7 Current month
F9-05 Clock : day Current day Current day
F9-06 Clock : hour Current hour Current hour
F9-07 Clock : minute Current minute Current minute
Group FE: Elevator function parameters
FE-01 Floor 1 display 1911: display B 1901
FE-02 Floor 2 display 1912: display G 1902
FE-03 Floor 3 display 1901: display 1 1903
FE-04 Floor 4 display 1902: display 2 1904
Group FP: User parameters
FP-00 User password 0: No password 0
0: No operation
FP-01 Parameter update 1: Restore default setting 0
2: Clear fault records
Unit
m/s
m/s
m/s
kg
Hz
kW
V
A
Hz
RPM
ms
ms
m/s²
m/s²
s
s
HH:MM
HH:MM
s
min
min
YYYY
MM
DD
HH
min
