FINAL DRAWINGS H2430

FREE-FALL LIFEBOAT DAVIT D-FH.100

- G1-6168 rev. Q dated 10.07.2017 Arrangement and data for
deckfoundation D-FH.100
- G1-6168 rev. H dated 10.07.2017 Item list
- G0-1709 rev. H dated 05.07.2018 Lashing & guide parts
- G0-1708 rev. I dated 10.02.2017 Arrangement track D-FH
- G1-6211 rev. K dated 10.08.2016 Arrangement hydraulic D-FH
- G1-6212 rev. F dated 02.08.2016 Arrangement electric D-FH
- G2-4667 rev. A dated 13.04.2015 Arrangement Traverse
- G1-6273 rev. A dated 17.09.2014 Greasing plan D-FH.100
- G1-6252 rev. A dated 24.02.2016 Assembly instructions D-FH
- G4-6868 rev. 0 dated 13.05.2014 Suspension 52 kN (low temperature)
- G3-6386 rev. A dated 14.08.2015 Sea lashing suspension
- G4-7763 rev. A dated 13.01.2016 Flange mounting
- G4-7217 rev. A dated 09.06.2016 Typical wire rope diagram
- G2-4726 rev. K dated 26.10.2016 Arrangement stairway
- G2-4940 rev. E dated 26.10.2016 Arrangement stairway (winch side)
- G2-4803 rev. B dated 17.06.2016 Arrangement winch 10 kNm
- G4-7241 rev. 0 dated 11.09.2014 Kinematic diagram
- G0-1731 rev. F dated 10.08.2016 Section winch 10 kNm
- G2-4862 rev. C dated 07.06.2016 Railing
- G2-5152 rev. A dated 22.03.2016 Lifting arrangement
- G3-7428E+R Launching procedure
- G3-7427E+R Launching procedure
- Hy1995A-D rev. 8 dated 29.07.2016 Hydraulic diagram
- U10/2/52/00 rev. 0 dated 16.08.2017 Electric diagram
- TD_D-FH rev. 0 dated 18.09.2018 Technical specification D-FH.100
- 1995-11-A-FAT rev. 0 dated 30.10.2017 Factory acceptance test D-FH.100
- Python Hoist S and C - Main wire rope data sheet
- Wire rope 6x36 - Sea lashing wire rope data sheet
- Instruction Manual D-FH.100 rev. 02/2017-11-07

For general purposes:

- G3-6333 rev. H dated 24.03.2018 Lubricant/oil recommendation
- Lubrication oil chart H2430 1995AC rev.0 dated 18.09.2018
- Spare parts list S 24420 1995_11AC
- DEC-14-NA-DI Non-asbestos Declaration
- DI-Hische Service Stations

Date of issue: 2018-09-18 EH

 OF

OE

LAUNCHING PROCEDURE LAUNCHING PROCEDURE

LAUNCHING PROCEDURE

LAUNCHING PROCEDURE

-
 1
d-i davit international gmbh

ITEM LIST of dwg. G1-6168 Date of issue 27.03.2014

mod. description date name

first issue 27.03.14 zb
A Item 03 -> G2-4803 added;
Items 15, 16 A4-80 instead of A4-70;
Item 16 quantity corrected. 01.09.14 EH
B Items 18-20 added, weight item 01,03,09 mod. 25.11.14 JB
C Item 21 added, item 09 exec. was 1.R.H/1.L.H
and weight updated, mass updated. 08.04.15 EH
D Weights updated. 19.10.15 EH
E Weights updated. 22.03.16 EH
F Item 10 was A3-1314, item 11 was G3-2166
and quantity was 1, weights updated. 27.10.16 EH
G Mass updated. 02.03.17 TR
H wire rope change from python HOIST S -> C 10.07.17 RL

Item q'ty description drawing/ remarks mass mass

item material steel purch.
____│_____│__________________________│__________│_________│_____│_____

** - Arr. and data for deckfound.

D-FH.100 G1-6168
01 1 Arr. track D-FH. G0-1708 R.H.exec 8875 97
02 1 Arr. davit arm D-FH. G1-6195 R.H.exec 6141 28
03 1 Arrangement winch 10 kNm G2-4803 950
04 1 Arr. traverse G2-4667 267 4
05 2 Suspension 52kN G4-6868 18
06 1 Lashing & guide parts G0-1709 R.H.exec 1138 36
07
08 1 Sea lashing suspension G3-6386 5
09 1 Arr. stairway G2-4726 1L.H.exec. 1046 17
10 1 Boarding instruction plate G3-7427 Engl.+Russ.
11 2 Boarding instruction plate G3-7428 Engl.+Russ.
12 1 Arr. hydraulic D-FH. G1-6211 R.H.exec 2300
13 1 Arr. electric D-FH. G1-6212 R.H.exec 52
14 1 20 mm, Python HOIST C, 1960 N/mm² St.galv. 146
minimum breaking load 373,7 kN,
greased, one side pressed
in thimble (for shaft ø50)
acc. DIN 3090, L=80 m
15 6 Hexagon screw M20*110 A4-80 DIN 931
16 6 Hexagon nut M20 A4-80 DIN 934
17 12 Washer A 21 A4 DIN 125
18 16 Hex. screw M4*20 A4 DIN 933
19 16 Hex. nut M4 A4 DIN 934
20 32 Washer A4.3 A4 DIN 125
21 1 Arr. stairway (winch side) G2-4940 1R.H.exec. 1205 17

mass steelwork: 18672 kg

mass purchase parts: 3670 kg
estimated total mass davit: 22342 kg
AZ BZ BW AW LW

BW AW LW AZ BZ
BW AW LW AZ BZ
 LAUNCHING PROCEDURE
5
1 REMOVE ALL PROTECTION CONNECT HOOKS AND TIGHTEN UP
COVERS
2 CHECK AND REMOVE 6
ANY OBSTRUCTION
3 REMOVE GRIPING GEAR EMBARKATION AND FASTEN SEATBELTS
OF DAVIT AND TRAVERSE
4 TURN OUT DAVIT ARM OVER
BOAT 7 8
RELEASE BOAT TURN OUT DAVIT ARM - CYLINDER OUT
SECURING DEVICE

9
1
LOWER TO THE WATER LOWERING
2
10
3
START ENGINE

4 11

RELEASE HOOKS WHEN WATERBORNE

12

SHEER OFF

G3-7428E+R
 LAUNCHING PROCEDURE
5
1 REMOVE ALL PROTECTION
COVERS SECURE HATCHES
2 CHECK AND REMOVE ANY
OBSTRUCTION
3 REMOVE GRIPE GEAR 6
4 EMBARKATION

FASTEN SEATBELTS

1 7

2 START ENGINE
3
4
8

LAUNCH BOAT

SHEER OFF

G3-7427E+R
Specification rev. 18.09.2018
Free-fall lifeboat system D-FH.
TECHNICAL DESCRIPTION

Shipyard: DSME / TEEKAY

NB: H 2430

Davit international ref. No. 1995-11-A-1

DAVIT TYPE D-FH.100

under-deck version

Contents:

01. GENERAL DESCRIPTION WITH APPLIED REGULATIONS

02. SYSTEM STRUCTURE

02.01. Davit track
02.02. Davit arm
02.03. Winch
02.04. Hydraulic system
02.05. Electric system
02.06. Reeving components
02.07. Suspension
02.08. Lashing / guiding system
02.09. Stairways

03. TECHNICAL DATA

03.01. Boat data
03.02. Davit data
03.03. Hydraulic data
03.04. Electric data
03.05. Painting specification and steel treatment
03.06. Dry weight of the system
03.07. Project drawing
03.08. Temperature

04. SCOPE OF SUPPLY PER DAVIT SYSTEM

d-i davit international-hische gmbh • P.O. Box 12 69 • 27223 Sulingen • Germany

Phone: +49 4271 9344-0 • Fax: +49 4271 9344-55 • e-mail: sales@di-hische.de
page 1
Specification rev. 18.09.2018
Free-fall lifeboat system D-FH.

01. GENERAL DESCRIPTION WITH APPLIED REGULATIONS

All equipment will be provided according to SOLAS 1974 with the protocol of 1978/1988 and
latest amendments including LSA code amendments and maritime regulation of vessel's registry
(CYPRUS) and classification society(RMRS).

Davit international will provide necessary certificates requested by SOLAS and/or concerned
authority (CYPRUS) and CLASS(RMRS) certificate.

The system is designed in that way, that all necessary functions, such as launching and recovery
of the boat, are fulfilled. The system can be operated in the free-fall mode, alternatively in the
powered launching/recovery mode.

The davit system corresponds to the enclosed arrangement drawing No. G1-6168.

The davit system is fixed on a free deck and is suitable for launching a fully manned boat from
the stowed position to the water level by means of gravity or by the hydraulic power system.

In order to allow a launching and recovery procedure as appropriate, the system is equipped
with a hydraulic winch. Hoisting of the fully equipped boat, including the crew (see ”technical
data sheet”), can be realised by means of the incorporated hydraulic motor.

The winch is equipped with a one section drum, which has to wind the lowering falls.

The control push buttons for controlling of turning-out/in and lowering/hoisting are placed on deck
and are of the "dead-man" type.

To assure a minimum of maintenance all shafts are of stainless steel. All sheaves and pivot points
contain life time lubricated bushes, in this way further greasing is reduced to the minimum.

d-i davit international-hische gmbh • P.O. Box 12 69 • 27223 Sulingen • Germany

Phone: +49 4271 9344-0 • Fax: +49 4271 9344-55 • e-mail: sales@di-hische.de
page 2
Specification rev. 18.09.2018
Free-fall lifeboat system D-FH.

02. SYSTEM STRUCTURE

The davit system type D-FH. consists of the following main items:

02.01. Davit track

1 davit track with integrated rollers for guiding the boat in free-fall mode. The track is a rigid
frame incorporating pivot shafts for davit arm and cylinders as well as all foundations for the
lashing components.

02.02. Davit arm

1 davit arm of the closed welded design, supported on the davit track. The arm is positioned by
the hydraulic cylinders and incorporates all required sheaves, pivot shafts and connection shafts.
The foundation for the winch has been integrated.

02.03. Winch
1 winch with the gears in a closed oil bath. Hydraulic motor is placed in a closed heated box. The
winch, suited for power driven hoisting and lowering procedures, consists of the following main
parts:
- single section drum, supported in roller type bearings.
- conventional speed reducer gear with built-on brake.
- hydraulic motor with brake valve (see ”hydraulic system”).

02.04. Hydraulic system

1 hydraulic system for controlling of the davit functions incorporating:
- 1 hydraulic power pack, built-under deck existing of an oil tank, an electric motor (see "electric
system”) with built-on hydraulic pump, pressure relief valve, electro/hydraulic control valves
and manometer.
- 2 hydraulic cylinders of the double acting type, containing self aligning bearings on each side
and executed with brake valves on either side.
- 1 hydraulic motor on the winch, hoisting/lowering the boat with the speed desired (see
"technical data sheet").
- 1 set hydraulic pipes and hydraulic hoses.

d-i davit international-hische gmbh • P.O. Box 12 69 • 27223 Sulingen • Germany

Phone: +49 4271 9344-0 • Fax: +49 4271 9344-55 • e-mail: sales@di-hische.de
page 3
Specification rev. 18.09.2018
Free-fall lifeboat system D-FH.

02.05. Electric system

1 electric system consisting of:
- 1 starter box for placing under-deck, with integrated controls. The starter box is built-on to the
power unit, is of the enclosure type IP 54 and contains a main switch and indicators as shown
in electric diagram.
- 1 transformer box for placing under-deck. The transformer box is built-on to the power unit, is of
the enclosure type IP 54 and contains indicators as shown in electric diagram.
- 1 control station for placing on-deck. The control station is built-on to the davit track, placed in
protection box, is of the enclosure type IP 66 and contains controls and indicators as shown in
electric diagram. A stand-by heating element has been integrated.
- 1 electric motor directly driving the pump through a flexible coupling (placed on power pack).
- 1 set electric cables between starter box and electric components.
- 1 set heater for winch.
- 4 set heater for wire rope sheave shaft.
- 1 set plug connection for heater (traverse).

02.06. Reeving components

1 galvanized wire rope running from the drum of the winch through the traverse to a fixed point.
The wire contains a spliced-in thimble on one side for proper mounting of the standing part.

02.07. Suspension
1 traverse with integrated sheaves, suspending the hoisting chains and recovery hooks.

02.08. Lashing / guiding system

1 set of lashing / guiding components for the handling and securing of the boat in a seaworthy
position.

02.09. Stairways
2 sets of stairways enabling control, ice removing and maintenance of the system.

d-i davit international-hische gmbh • P.O. Box 12 69 • 27223 Sulingen • Germany

Phone: +49 4271 9344-0 • Fax: +49 4271 9344-55 • e-mail: sales@di-hische.de
page 4
Specification rev. 18.09.2018
Free-fall lifeboat system D-FH.
03. TECHNICAL DATA

03.01. Boat data

Make: Ernst Hatecke GmbH
Type: GFF 9.8C-T
Dimensions: 9,87 x 2,84 x 3,30 m (L/W/H)
Number of persons: 50 persons
Weight, incl. equipment: 6025 kg
Weight, incl. crew (3 persons): 6273 kg
Weight, incl. 50 persons: 10150 kg

03.02. Davit data

Max. SWL : 100 kN
Hoisting / lowering speed: min. 4 m/min
Operating conditions sliding ramp/A-frame:
- list 20°/5°
- trim 10°/2°

03.03. Hydraulic data

Oil flow: 50 l/min
Oil pressure: 24000 kPa

03.04. Electric data

Motor voltage: 3 x 440 V
Cycles: 60 Hz
Electro motor power: 24 kW
Control voltage: 3 x 230 V
Starter box: IP 54
Heating ~ 1,9 kW (230V)

d-i davit international-hische gmbh • P.O. Box 12 69 • 27223 Sulingen • Germany

Phone: +49 4271 9344-0 • Fax: +49 4271 9344-55 • e-mail: sales@di-hische.de
page 5
Specification rev. 18.09.2018
Free-fall lifeboat system D-FH.
03.05. Painting specification and steel treatment:

Davits and other steel parts outside

Steel treatment according to Steel treatment according to Production Standard of German

Shipbuilding Industry 7. Edition / Section 2.9 Areas of application "V".

Surface preparation
Full blasting SA 2,5 according to ISO 8501-1

Coating Scheme Color

1 x 100 µm Intergard 7600 Red Aluminium
1 x 100 µm Intergard 7600 Grey
1 x 50 µm Interthane 990 White (PHB000)
1 x 50 µm Interthane 990 White (PHB000)

The professional work will be done in acc. with the paint suppliers instruction.
The paint manufacture International Paint.
The weld area for mounting has to be left uncoated. The coating will be stepped down in this area.

Galvanized parts outside

Steel treatment according to Production Standard of German Shipbuilding Industry 7. Edition

/ Section 2.9 Areas of application "V".

Galvanizing acc. to DIN EN ISO 1461

Surface Preparation
degreasing, roughn, cleaning

Coating Scheme Color

1 x 100 µm Hempel’s HB primer K150 White (1X030)
1 x 50 µm Interthane 990 White (PHB000)
1 x 50 µm Interthane 990 White (PHB000)

d-i davit international-hische gmbh • P.O. Box 12 69 • 27223 Sulingen • Germany

Phone: +49 4271 9344-0 • Fax: +49 4271 9344-55 • e-mail: sales@di-hische.de
page 6
Specification rev. 18.09.2018
Free-fall lifeboat system D-FH.

Stainless steel parts outside

Steel treatment according to Production Standard of German Shipbuilding Industry 7. Edition

/ Section 2.9 Areas of application "V".

Surface Preparation
degreasing, roughn, cleaning

Coating Scheme Color

1 x 100 µm Hempel’s HB primer K150 White (1X030)
1 x 60 µm Interthane 990 White (PHB000)

Steel parts inside

Steel treatment according to Steel treatment according to Production Standard of German

Shipbuilding Industry 7. Edition / Section 2.9 Areas of application "V".

Surface preparation
Full blasting SA 2,5 according to ISO 8501-1

Coating Scheme Color

1 x 100 µm Intergard 7600 Red Aluminium

03.06. Dry weight of the system: approx. 22.122 kg

03.07. Project drawing: No. G1-6168

03.08. Temperature: operation temperature –52°C

d-i davit international-hische gmbh • P.O. Box 12 69 • 27223 Sulingen • Germany

Phone: +49 4271 9344-0 • Fax: +49 4271 9344-55 • e-mail: sales@di-hische.de
page 7
Specification rev. 18.09.2018
Free-fall lifeboat system D-FH.
04. SCOPE OF SUPPLY PER DAVIT SYSTEM Packing No.
1. Track lower part (R.H. exec. – winch side) 1 pc. 101
2. Track lower part (L.H. exec.) 1 pc. 102
3. Track upper part (R.H. exec. – winch side) 1 pc. 103
4. Track upper part (L.H. exec.) 1 pc. 104
5. Track embarkation part incl. platform grating 1 pc. 105
6. Track connection beam 1 pc. 106
7. Railing 1 pc. 107
8. Railing 1 pc. 108
9. Railing 1 pc. 109
10. Davit arm (R.H. exec. – winch side) 1 pc. 110
11. Davit arm (L.H. exec.) 1 pc. 111
12. Davit arm upper part 1 pc. 112
13. Traverse 1 pc. 113
14. Suspension 52 kN 2 pc. 114
15. Arm support (1R.H./1L.H.) 2 pc. 115
16. Skid plate 2 pc. 116
17. Lashing unit keel (R.H. exec.) 1 pc. 117
18. Pelican hook for lashing unit (keel) 1 pc. 117a
19. Fender guide 4 pc. 118
20. Lashing unit 2 pc. 119
21. Lashing (keel) 1 pc. 120
22. Lashing (aft) 1 pc. 121
23. Sea lashing suspension 2 pc. 122
24. Stairway lower part (R.H. exec. – winch side) 1 pc. 123
25. Stairway upper part (R.H. exec. – winch side) 1 pc. 124
26. Stairway lower part (L.H. exec.) 1 pc. 125
27. Stairway upper part (L.H. exec.) 1 pc. 126
28. Hydraulic power pack incl. starter and transformer box 1 pc. 127
29. Hydraulic cylinder 2 pc. 128
30. Hydraulic flexible hoses 8 set 129
31. Control station 1 pc. 130
32. Plug connection for heater with cable 1 pc. 131
33. Wire rope 20mm 1 pc. 132
34. Boarding instruction plate (English + Russian) 1 pc. 133
35. Boarding instruction plate (English + Russian) 2 pc. 134
36. EC/MED Certificates 1 set 135
37. Instruction Manuals (4 Russian, 4 English) + 1 CD-Rom 8 set 136
38. Metal box with spare parts 1 pc. 137
39. Intermediate piece for stairway (Pipe 33,7x3,2 L=730) 4 pc. 141
40. Intermediate piece for stairway (Round steel ø12 L=730) 8 pc. 142

d-i davit international-hische gmbh • P.O. Box 12 69 • 27223 Sulingen • Germany

Phone: +49 4271 9344-0 • Fax: +49 4271 9344-55 • e-mail: sales@di-hische.de
page 8
Specification rev. 18.09.2018
Free-fall lifeboat system D-FH.
41. Stairway support (Winch side) 1 pc. 143
42. Stairway support 1 pc. 144
43. Winch 10 kNm 1 pc. 145
44. Support for stairway railing 6 pc. 146

NOTE:
For details see packing and label list. Each part of delivery will be marked with packing numbers.

d-i davit international-hische gmbh • P.O. Box 12 69 • 27223 Sulingen • Germany

Phone: +49 4271 9344-0 • Fax: +49 4271 9344-55 • e-mail: sales@di-hische.de
page 9
 Manufacturer: d-i davit international-hische GmbH Date: 07.12.2017
41 s p i Model: D-FH.100 Organization: d+i MED
Launching & Recovery Appliances Lot / Serial Number: 1995-11-A-l Surveyor: Mr. Mohr

FACTORY ACCEPTANCE TEST PROGRAM

for Launching appliances for free-fall lifeboats
of the Type
D-FH.100

Index

1. Submitted drawings, reports and documents

2. Quality Assurance
3. Visual inspection
4. Static proof load test (davit and winch)
5. Operational load test (davit and winch)

Issued by

d-i davit international-hische GmbH f\\ ------\//

D N V -G L
Sandstrasse 20, 27232 Sulingen, Germany
^ ISO 9001 ^

Form: FM 7 5.3-Stan d : l.Ovom 08.12.2014 Revision / Date of Issue: 0/ 2017-10-30 Name: AD Page: 1/8
 Manufacturer: d-i davit international-hische GmbH Date: 07.12.2017
A - ^ m
y ^ i Model: D-FH.100 Organization: d+i MED
launching & Recovery Appliances Lot / Serial Number: 1995-11-A-l Surveyor: Mr. Mohr

FAT
Free-Fall Launching and Recovery Appliances

Summary

Manufacturer: d-i davit international-hische GmbH

Sandstraße 20
27232 Sulingen
Germany
Phone +49 4271 9344 0

Crane/Davit System Type: D-FH.100

Lot / Serial Number: 1995-11-A-l

Maximum Working Load: 104,0 kN

Maximum Turning Moment: -

Winch type: 10.01.01

Date: 07.12.2017

Place: Sulingen

Name and Signature of Surveyor: Mr. Mohr

Approval Organization / Hull: d+i MED / H2429

Form: FM 7-5.3 -Sta n d : 1.0 vom 08.12.2014 Revision / Date of Issue: 0/ 2017-10-30 Name: AD Page: 2/8
 Manufacturer: d-i davit international-hische GmbH Date: 07.12.2017
Ut I
Launching & Recovery Appliances
Model:
Lot/Serial Number:
D-FH.100
1995-11-A-l
Organization:
Surveyor:
d+i MED
Mr. Mohr

1. Submitted Drawings, Reports and Documents

Number Revision No. & Date Title Status
Info: As shown in letter to RMRoS dated 2014-07-25. Approved
Info: Certificate No. 14.08425.272 dated 10.03.2015 14.08425.272
info: 314-41-178946 Extention of approval - Davits for DSME-Korea hulls 2421 to 2434 Approved
MED: 14 702 - 15 HH & MED000017H for davit system Certified B & D
MED: 14 703 - 15 HH & MED000017H for winch Certified B & D

/ W P i'L

( t Ä 'M .K m

Form: FM 7-5.3 - Stand: 1.0 vom 08.12.2014 Revision / Date of Issue: 0/ 2017-10-30 Name: AD Page: 3/8
 Manufacturer: d-i davit international-hische GmbH Date: 07.12.2017
d#i
li
Launching & Recovery Appliances
Model:
Lot/Serial Number:
D-FH.100
1995-11-A-l
Organization:
Surveyor:
d+i MED
Mr. Mohr

2. Quality Assurance Regulations: MSC.81(70) 2/1.1 and 1.2

Quality Assurance

Except where all appliances o f a particular type are required by chapter III of the Standard Used: ISO 9001:2008
International Convention for the Safety of Life at Sea, 1974, as amended, or the
International Life-Saving Appliance (LSA) Code, to be inspected, representatives of the Quality Assurance Procedure: Quality handbook
Administration should make random inspection of manufacturers to ensure that the quality
of life-saving appliances and the materials used comply with the specification of the Quality Assurance Manual: Quality handbook
approved prototype life-saving appliance.
Description of System: As certified with 156581-2014-AQ-GER-DAkks.
Manufacturers should be required to institute a quality control procedure to ensure that life­
saving appliances are produced to the same standard as the prototype life-saving appliance
approved by the Administration and to keep records of any production tests carried out in Quality Assurance System acceptable: Yes /-Ne—
accordance with the Administration’s instructions.
Comments/Observations:

Form: FM 7-5.3-Sta n d : 1.0 vom 08.12.2014 Revision / Date of Issue: 0/ 2017-10-30 Name: AD Page: 4/8
 4l=rl
Launching & Recovery Appliances
Manufacturer:
Model:
Lot / Serial Number:
d-i davit international-hische GmbH
D-FH.100
1995-11-A-l
Date:
Organization:
Surveyor:
07.12.2017
d+i MED
Mr. Mohr

3. Visual inspection Regulations:

Test Procedure Acceptance Criteria Significant Test Data

Confirm that installation has been manufactured to the Visually inspect the appliance. Passed/ failed
approved drawings.
Conduct measurements if required.

Confirm the applied materials. Presentation of the material certificates. Passed / Failed

Comments/Observations n c^ c

!C

Form: FM 7-5.3 - Stand: 1.0 vom 08.12.2014 Revision / Date of Issue: 0/ 2017-10-30 Name: AD Page: 5/8
 Manufacturer: d-i davit international-hische GmbH Date: 07.12.2017
<l#i
Launching & Recovery Appliances
Model:
Lot / Serial Number:
D-FH.100
1995-11-A-l
Organization:
Surveyor:
d+i MED
Mr. Mohr

4. Static proof load Test Regulations:

Test Procedure Acceptance Criteria Significant Test Data

The launching appliances for lowering a free-fall lifeboat by The launching appliance and its attachments as well as the MWL: 104,0 kN (10400 kg)
falls, should be subjected to a static proof load of 2.2 times winch brake should be of sufficient strength to withstand a
the maximum working load at the full outboard position. static proof load on test of not less than 2.2 times the Test load (2.2 x MWL): 228,8 kN (22880 kg)
maximum working load.
Winch will be mounted and also subjected to a static proof
load o f 2.2 times, which is more than required (1.5 times the
maximum working load.”

There should be no evidence of significant deformation

or other damage:

Deformations should be measured at points “A” and “B” as Deformation measured:

shown.
Point “A” : 'lo Z mm

Point “B” : Ò & mm

Passed / -Ffti+eä-

Comments / Observations m o n e
MEASURE
POINT B

Form: FM 7-5.3 - Stand: 1.0 vom 08.12.2014 Revision / Date of Issue: 0/ 2017-10-30 Name: AD Page: 6/8
 Manufacturer: d-i davit international-hische GmbH Date: 07.12.2017
Ut 1 Model:
Lot / Serial Number:
D-FH.100
1995-11-A-l
Organization:
Surveyor:
d+i MED
Mr. Mohr
Launching & Recovery Appliances

5. Operational load test Regulations:

Test Procedure Acceptance Criteria Significant Test Data

Form: FM 7-5.3 - Stand: 1.0 vom 08.12.2014 Revision / Date of Issue: 0/ 2017-10-30 Name: AD Page: 7/8
 ♦ ■ Manufacturer: d-i davit international-hische GmbH Date: 07.12.2017
<l#i
Launching & Recovery Appliances
Model:
Lot / Serial Number:
D-FH.100
1995-11-A-l
Organization:
Surveyor:
d+i MED
Mr. Mohr

6. Safety limit test Regulations:

The end positions of the hydraulic cylinders o f the arm When reaching the end positions the hydraulic cylinder Overload system was tested:
should be tested to verity limit protection systems for movement should stop and the relief valves should open to
extension and retraction end positions. protect the arm-hydraulic system from overload. Arm at max. outboard position: 2*1.V MPa

The hoisting limit protection system of the winch should be When reaching the end position of the hoisting with the
tested. suspension the movement should stop and the relief valves Arm at max. inboard position: I h .d MP o,
should open to protect the winch-hydraulic system from
overload.

Winch hoisted suspension to contact position with arm:

ll.O M P a

Result:

Passed/Eaikd-

Comments/Observations none

Form: FM 7-5.3 - Stand: 1.0 vom 08.12.2014 Revision / Date of Issue: 0/ 2017-10-30 Name: AD Page: 8/8
 Òò ÔÛÊÛÒÌÛÎ×Í Íòßò
íî ßÍÕÔ×Ð×ÑË ­¬®ò ÙÎóïèëìë Ð×ÎßÛËÍ ó ÙÎÛÛÝÛ
ÛÔ æ õíð îïð ìîîðëèï øïî Ô×ÒÛÍ÷
ÚßÈ æõíð îïð ìïéîïìî
©©©ò´»ª»²¬»®·­ò¹®
ÛóÓß×Ôæ ´»ª»¼»®·à±¬»²»¬ò¹®

ÍÌÛÛÔ ÎÑÐÛÍ ©·¬¸ º·¾»® ½±®» ê ¨ íê ÉßÎÎ×ÒÙÌÑÒ ÍÛßÔÛ ø Ü×Ò íðêì ÷

ê ¨ ø ï õ éõ øéõé÷ õ ïì ÷

Ò±³·²¿´ É»·¹¸¬ Ý¿´½«´¿¬»¼ Þ®»¿µ·²¹ Ú±®½» Ó·²·³«³ Þ®»¿µ·²¹ Ú±®½»

¼·¿³»¬»® °»® ø ÝÞÚ ÷ ø ÓÞÚ ÷
ú ¿½½»°¬¿¾´» ³»¬»®
¬±´»®¿²½» º±® ©·®» ²±³·²¿´ ­¬®»²¹¬¸

ײ ½¿­» ¿ ­¬»»´ ½±®» ®»°´¿½»­ ¬¸» º·¾»® ½±®»

ïò ̸» ©»·¹¸¬ ·²½®»¿­»­ ïðû
îò ̸» ÝÞÚ ·²½®»¿­»­ ïêû
íò ̸» ÓÞÚ ·²½®»¿­»­ èû
 INSTRUCTION MANUAL FOR:

davit system: Free-fall lifeboat handling system

type: D-FH.100

yard: DSME / Teekay

hull no.: H 2430

supplier: d-i davit international-hische gmbh

Sandstrasse 20
27232 Sulingen
Germany

suppliers reference no.: 1995-11-A-1

classification: RMROS / EC (MED)

requirements: Solas 1974, with latest amendments

design temperature: -52°C WINTERIZATION (-52)

rev.00/2017-07-18/ RL
rev.01/2017-08-08/ EH
rev.02/2017-11-07/ zb

d-i davit international-hische GmbH Delivery address: Managing directors: Bank details:
Sandstr. 20, 27232 Sulingen Berliner Str. 73-75 Felizitas Hische
Postfach 12 69, 27223 Sulingen 27232 Sulingen Dipl.-Ing. Fritz Hische Volksbank Sulingen
Germany Dipl.-Ing. (FH) Joachim Wiese IBAN DE20 2569 1633 0008 9931 00
Tel.: +49 4271 93 44-0 HR B 203844 Dipl.-Ing. Zdenko Bujdo BIC (SWIFT) GENODEF1SUL
Fax: +49 4271 93 44-55 AG Walsrode Commerzbank Diepholz
info@di-hische.de IBAN DE45 2564 1302 0620 2428 00
www.di-hische.de Tax No. 45 202 04800 VAT No. DE 116581505 BIC (SWIFT) COBADEFFXXX
d-i davit international-hische gmbh pg.2
Manual
system free-fall system for lifeboat D-FH.

0 INDEX

0 INDEX 2

1 PARTICULARS 4

1.1 LAUNCHING APPLIANCE DATA 4

1.2 LIST OF ACCOMPANYING INFORMATION SHEETS 5
1.3 LIST OF ACCOMPANYING DRAWINGS 6
1.4 PAINTING INSTRUCTIONS 7

2 LAUNCHING SYSTEM 8

2.1 GENERALITIES 8
2.2 LAUNCHING INSTRUCTIONS 10
2.3 CRAFT LAUNCHING AND RECOVERY 10
2.3.1 PREPARATIONS BEFORE LAUNCHING 10
2.3.2 FREE-FALL LAUNCHING PROCEDURE 12
2.3.3 POWER DRIVEN LAUNCHING PROCEDURE 13
2.3.4 RECOVERY PROCEDURE 15
2.3.5 SIMULATED FREE-FALL LAUNCHING PROCEDURE 21
2.4 GRIPE GEAR (LASHING GEAR) 26
2.5 WINCH 26
2.6 ELECTRICS 26
2.6.1 ELECTRIC MOTOR 26
2.6.2 STARTER BOX 27
2.6.3 TRANSFORMER BOX 27
2.6.4 CONTROL STATION 28
2.6.5 HEATING ELEMENTS 28

3 WINCH SYSTEM 29

3.1 BASIC WINCH DESCRIPTION 29

3.1.1 DRUM 29
3.1.2 SPEED REDUCER GEAR 29
3.1.3 MOTOR POWER UNIT 29
3.2 FUNCTIONAL DESCRIPTION 29
3.2.1 HOISTING BY HYDRAULIC POWER 29
3.2.2 LOWERING BY HYDRAULIC POWER 29

4 RECOMMENDED LUBRICANTS 30

5 MAINTENANCE 30

5.1 MAINTENANCE GROUP 1, DAILY INSPECTION 31

5.1.1 VISUAL INSPECTION 31
5.2 MAINTENANCE GROUP 2, ONE WEEK SERVICE 31
5.2.1 HYDRAULIC FLUID LEVEL 31
5.2.2 AIR CONDITIONER CHECK 31
d-i davit international-hische gmbh pg.3
Manual
system free-fall system for lifeboat D-FH.

5.3 MAINTENANCE GROUP 3, THREE MONTHS SERVICE 32

5.3.1 DAVIT (GREASING) 32
5.3.2 WINCHES (GREASING) 32
5.3.3 WIRE ROPES (GREASING) 32
5.3.4 SHEAVES 32
5.3.5 OIL LEVEL CHECK 32
5.3.6 DRAIN OFF CONDENSATE 32
5.4 MAINTENANCE GROUP 4, ONE YEAR SERVICE 33
5.4.1 HYDRAULIC SYSTEM (OIL CHANGE) 33
5.4.2 WINCHES (OIL CHANGE) 33
5.4.3 INSTALLING/CHANGING OF WIRE ROPES 33
5.4.4 PAINTING 33
5.4.5 SPARE PARTS 33
5.5 MAINTENANCE GROUP 5, FIVE YEAR SERVICE 34
5.5.1 WIRE ROPES 34
5.6 HOSE LINES (REPLACING) 34
5.7 LOG FOR INSPECTIONS AND MAINTENANCE 34

6 SPARE PARTS 34
d-i davit international-hische gmbh pg.4
Manual
system free-fall system for lifeboat D-FH.

1 PARTICULARS

In this chapter the generalities of the life saving appliance above

mentioned and of this manual will be given.

1.1 LAUNCHING APPLIANCE DATA

davit system: free-fall lifeboat handling

system
supplier: d-i davit international-hische gmbh
supplier's reference no.: 1995-11-A-1

system type: D-FH.100

s.w.l.: 104,0 kN
winch type: 10.01.01
s.w.l. on winch drum: 45,0 kN
oil capacity gearbox: approx. 40 l (see G3-6333)1)

oil capacity hydraulic power unit: approx. 300 l

hydraulic unit, pump type: gear type (see G3-6333)

craft to be launched: lifeboat

type: GFF 9,8C-T
make: Hatecke
permissible capacity: 50 persons
dimensions: 9,87 * 2,84 * 3,30 m
empty weight in equipped condition: 60,25 kN
weight, fully equipped and boarded: 101,50 kN

wire rope falls

type: PYTHON HOIST C, 1960N/mm²
minimum breaking strength: 373,7 kN
diameter: 20 mm
length: 80 m

starterbox type: under deck

enclosure class: IP 66

1)
Oil bath lubricated winches, winch gearbox
d-i davit international-hische gmbh pg.5
Manual
system free-fall system for lifeboat D-FH.

1.2 LIST OF ACCOMPANYING INFORMATION SHEETS

For a better understanding of the text in the several chapters the

following documents have been inserted:

Description reference no.

boarding instruction plate (free-fall) G3-7427

boarding instruction plate (by falls) G3-7428

kinematic diagram winch 10.01. G4-7241

lubricant / oil recommendation G3-6333

d-i davit international-hische gmbh pg.6
Manual
system free-fall system for lifeboat D-FH.

1.3 LIST OF ACCOMPANYING DRAWINGS

For reason of simplifying the installation works, the boarding procedure

and the maintenance the following documents have been inserted:

Description reference no.

arrangement and data for deckfoundation D-FH.100 G1-6168

arrangement winch, type 10.01 G2-4803

section winch 10 kNm G0-1731

arrangement traverse G2-4667

suspension 52 kN G4-6868

lashing and guide parts G0-1709

sea lashing suspension G3-6386

arrangement hydraulic G1-6211

arrangement electric G1-6212

assembly instructions G1-6252

flange mounting G4-7763

typical wire rope diagram G4-7217

greasing diagram G1-6273

hydraulic circuit diagram Hy1995A-D

electric circuit diagram U10/2/52/00

list of authorised service stations

d-i davit international-hische gmbh pg.7
Manual
system free-fall system for lifeboat D-FH.

1.4 PAINTING INSTRUCTIONS

Unless a paint system has been ordered separately, the davit system
supplied has been sandblasted SA 2,5 and covered with one layer of
primer. Thickness of this coat is 15-20 microns.

UNPROTECTED STORAGE FOR MORE THAN 3 MONTHS IS NOT ALLOWABLE, unless a

further paint system has been applied.

All damage to the paint system is to be announced and

repaired immediately by the crew.
d-i davit international-hische gmbh pg.8
Manual
system free-fall system for lifeboat D-FH.

2 LAUNCHING SYSTEM

A summary of the most important particulars of the launching appliance

as well as those of the craft to be launched is given in the preceding
chapter. The appliance is capable of handling a life saving craft of
specified dimensions and capacity, comprising a total of:

- lifeboats: the permissible number of persons as specified on

page 4.

Details of design as well as further particulars of the equipment follow

from the accompanying documents.

To avoid possible injury or death, read this manual and

the instructions of the craft builders carefully before
using this system.

2.1 GENERALITIES

The life saving system is designed in that way that all necessary
functions for hoisting and lowering of the craft are fulfilled. The
system corresponds to the enclosed arrangement drawing.

The D-FH davit system is designed for launching boats in free-fall and
for recovering these boats with the davit. This type of D-FH system is
also suitable for launching a boat including the full complement of
persons, power-driven, from the launching position to the sea level.
This procedure can be introduced from the control stand at the aft
outboard railing.

It will be evident that this davit system requires an embarkation

platform on the stowed position level.

Recovery/powered launching of the boat can be introduced from the

control stand near the aft outboard railing. For the hoisting winch as
well as for the main cylinders control buttons have been installed. By
activating the "hoisting"-button the load can be lifted to the highest
position. By reaching this position the hydraulic hoisting motor will
stop, thanks to the incorporated pressure safety valve; actuating of the
control button should be stopped as soon as possible in order to prevent
excessive heating of the oil.

By activating the "cylinder out” and “cylinder in” button the position
of the davit arm can be controlled. By reaching the full inboard or
outboard position, the hydraulic cylinders will stop, thanks to the
incorporated pressure safety valve; actuating of the control button
should be stopped as soon as possible.

For the reasons of safety, the design of the control buttons is such
that an immediate braking power is available as soon as actuation of the
lever is discontinued; "dead-man"-type controls are being applied.
d-i davit international-hische gmbh pg.9
Manual
system free-fall system for lifeboat D-FH.

To assure a minimum of maintenance all shafts are of stainless steel.

The hydraulic cylinders incorporate spherical ball bearings which need

additional greasing.

The sheaves and pivot points include lifetime lubricated bushes. This
way further greasing is reduced to the minimum.
d-i davit international-hische gmbh pg.10
Manual
system free-fall system for lifeboat D-FH.

2.2 LAUNCHING INSTRUCTIONS

To assure a safe and well-executed launching, for each davit

system, an instruction plate has been installed. This
instruction plate, showing the exact sequence of the
launching procedure is placed near the embarkation position.
By following the instructions one by one safe launching is
guaranteed. Nevertheless the complete procedures for a safe
launching and recovering will be reviewed in the next
paragraph. In addition to the following operation guide the
boat manual has to be used in parallel to fulfil the boat
specific tasks when necessary.

2.3 CRAFT LAUNCHING AND RECOVERY

For a safe launching the following actions should be taken by the boat
handling crew:

2.3.1 PREPARATIONS BEFORE LAUNCHING

No. Operation Guide Schematic Diagram

1 Remove all protection covers.
2 Check and remove any
obstruction.
3 Disconnect boat battery
charger and traverse heater
plugs.
d-i davit international-hische gmbh pg.11
Manual
system free-fall system for lifeboat D-FH.

4 Remove boat gripe gears.

5 Check boat drains. See boat manual for details.

d-i davit international-hische gmbh pg.12
Manual
system free-fall system for lifeboat D-FH.

2.3.2 FREE-FALL LAUNCHING PROCEDURE

No. Operation Guide Schematic Diagram

1 Embarkation.
2 Secure hatches. See boat manual for details.
3 Assure each person is well- See boat manual for details.
seated and firmly secured by
the securing straps.
4 Start engine and release the See boat manual for details.
boat securing device, follow-
ing the instructions as given
by the boat builder.

Close the valve and operate

hydraulic pump.

After about 20 strokes the

locking device will disengage
– the lifeboat is now free.
d-i davit international-hische gmbh pg.13
Manual
system free-fall system for lifeboat D-FH.

2.3.3 POWER DRIVEN LAUNCHING PROCEDURE

No. Operation Guide Schematic Diagram

1 Release the traverse griping
gear, situated on the embar-
kation platform (both side).

2 Lower the recovery hooks by

activating the “lowering”
button on the control stand.

3 Connect recovery hooks with

boat suspension and tighten
the suspension by activating
the “hoisting”-button on the
control stand.
d-i davit international-hische gmbh pg.14
Manual
system free-fall system for lifeboat D-FH.

4 Embarkation.
5 Turn out davit arm to the
maximum outboard position by
pushing the “cylinder out”
button on the control stand.

6 Lower the boat by pushing the

“lowering” button on the
control stand.

7 Start engine of survival See boat manual for details.

craft, following the instruc-
tions of the boat builder.
8 Release the boat release gear See boat manual for details.
when the boat is waterborne.
d-i davit international-hische gmbh pg.15
Manual
system free-fall system for lifeboat D-FH.

2.3.4 RECOVERY PROCEDURE

The recovery of any life saving craft is only allowed with a

crew of:
-lifeboats: 3 persons
NOTE:

No. Operation Guide Schematic Diagram

1 Turn out the davit to the
maximum outboard position by
pushing the “cylinder out”
button on the control stand.

2 Lower the recovery hooks.

3 Make sure the wire rope falls
contain slack and fasten the
recovery hooks in the boat
suspension.
d-i davit international-hische gmbh pg.16
Manual
system free-fall system for lifeboat D-FH.

4 Start hoisting from the

control stand near the
outboard railing.

5 Ensure each wire rope turn

remaining permanently on the
winch drum to be kept close
to the adjacent one until
rope slack is eliminated by
rope tautening.

6 When reaching a position

about 3,0m below the highest
position the hoisting proce-
dure has to be stopped.
d-i davit international-hische gmbh pg.17
Manual
system free-fall system for lifeboat D-FH.

7 By controlling the main

cylinders from the control
stand the boat has to be
placed on the track. Ensure
smooth and safe operation,
avoid boat pending and
rotation.

8 Before replacing the boat in

the stowed position, the
hydraulic piston should be
brought back into its housed
position by opening the valve
screw in boat.
See boat manual for details!

9 Turn in the davit arm a bit

more and start hoisting on
the winch in that way that
the boat will move upwards
the track.
Stop hoisting immediately
when the boat reaches its
resting position.

RESTING POSITION!!
d-i davit international-hische gmbh pg.18
Manual
system free-fall system for lifeboat D-FH.

10 Check whether the hoisting

wires have been spooled up as
appropriate.

11 Release the two recovery

hooks from the boat suspen-
sion.

12 Turn in the davit arm to its

stowed position.
d-i davit international-hische gmbh pg.19
Manual
system free-fall system for lifeboat D-FH.

13 Replace boat gripe gears.

14 Stow the recovery traverse by

means of the lashing wires on
the embarkation platform.
d-i davit international-hische gmbh pg.20
Manual
system free-fall system for lifeboat D-FH.

15 Connect boat battery charger

and traverse heater plugs.

16 For preparing the craft for

stowing, follow the instruc-
tions as given in the manual
of the survival craft.
17 Replace all protection
covers.
d-i davit international-hische gmbh pg.21
Manual
system free-fall system for lifeboat D-FH.

2.3.5 SIMULATED FREE-FALL LAUNCHING PROCEDURE

In order to meet test requirements of IMO MSC/Circ. 1137 and prevent

failure of the lifeboat release hook due to suffering the force for a
long time, simulation of free-fall release as well as maintenance of the
release hook will be performed each 6 months.

No. Operation Guide Schematic Diagram

1 For preparation before
launching follow the proce-
dure described under 2.3.1

1. Remove all protection

covers.
2. Check and remove any
obstruction.
3. Disconnect boat battery
charger and traverse
heater plugs.
4. Remove boat gripe gears.
5. Check boat drains.

2 Release the traverse griping

gear, situated on the embar-
kation platform (both side).

3 Lower the recovery hooks by

activating the “lowering”
button on the control stand.
d-i davit international-hische gmbh pg.22
Manual
system free-fall system for lifeboat D-FH.

4 Connect recovery hooks with

boat suspension and tighten
the suspension by activating
the “hoisting”-button on the
control stand.

5 Embarkation.
Under the supervision of
principal, the attending crew
enter into lifeboat and
fasten safety belt.

d-i recommendation is only 1

operator.

6 Check once more if suspension

wires are under tension.

If necessary tighten the

suspension by activating the
“hoisting”-button on the
control stand.

7 After receiving the instruc- See boat manual for details.

tion of principal, appointed
operator starts the release
device.
Close the valve and operate
hydraulic pump.

After about 20 strokes the

locking device will disengage
– the lifeboat is now free.

The lifeboat slides down 100-

200mm.

Release hook is now free to

perform check, maintenance or
repair.
d-i davit international-hische gmbh pg.23
Manual
system free-fall system for lifeboat D-FH.

8 Upon the completion of the

works mentioned above, start
recovery procedure.

Before replacing the boat in

the stowed position, the
hydraulic piston should be
brought back into its housed
position by opening the valve
screw in boat.

See boat manual for details!

9 Start hoisting on the winch

in that way that the boat
will move upwards the track.
Stop hoisting immediately
when the boat reaches its
resting position.

RESTING POSITION!!

10 Release the two recovery

hooks from the boat suspen-
sion.
d-i davit international-hische gmbh pg.24
Manual
system free-fall system for lifeboat D-FH.

11 Replace boat gripe gears.

12 Stow the recovery traverse by

means of the lashing wires on
the embarkation platform.
d-i davit international-hische gmbh pg.25
Manual
system free-fall system for lifeboat D-FH.

13 Connect boat battery charger

and traverse heater plugs.

14 For preparing the craft for

stowing, follow the instruc-
tions as given in the manual
of the survival craft.
15 Replace all protection
covers.
d-i davit international-hische gmbh pg.26
Manual
system free-fall system for lifeboat D-FH.

2.4 GRIPE GEAR (LASHING GEAR)

When not actually in use, the craft should be securely stowed for sea
trail; the way in which the gripe lines have to be applied, as well as
further details, follow from the accompanying arrangement plan.

By applying this gripe gear, the craft is secured in a seaworthy

position.

To prepare the davit for the launching operation, the boat has to be
made ready by first slipping the gripe lines.

2.5 WINCH

To satisfy the launching and recovery of the survival craft, the

launching appliance is equipped with a winch; for enabling the craft
suspended by the wire rope falls, to be launched and recovered as
appropriate.

In essence the launching of each free-fall boat can be executed by free-

fall and/or motor driven.

For the purpose of craft recovery/launching by hydraulic power the winch

is executed with a hydraulic motor.

The winch system will be explained further in this manual.

2.6 ELECTRICS

The launching/recovery of the lifeboat is performed by means of a

hydraulic motor, situated on the winch. The hydraulic power pack
contains an electric motor, driving the hydraulic pump.

The electric control system is shown on the accompanying drawing

"electric circuit diagram". It comprises the following main items:

- Electric motor, situated in the power pack.

- Starter box, enclosure IP54.
- Transformer box, enclosure IP54.
- Control station, placed in protection box enclosure IP 66.
- Heating elements for sheave bolts, oil in gearbox, hydrau-
lic motor, winch housing and protection box.
- Plug connection for heater (traverse).

2.6.1 ELECTRIC MOTOR

The electric motor 9M2 is mounted in the hydraulic power unit
(placed under deck) directly driving the pump via a flexible
coupling.
d-i davit international-hische gmbh pg.27
Manual
system free-fall system for lifeboat D-FH.

2.6.2 STARTER BOX

The starter box is placed on power pack under deck and is of
the enclosure class IP54.
The following controls/alarms are situated on the starter
box:
- MAIN POWER SWITCH (8Q2), with this switch the electric
supply to the electric motor 9M2 can be controlled.
- MAIN SUPPLY indicator (15H11)- This indicator lights up as
soon as the ship’s control centre and the main power switch
allow electric supply from the ship’s main supply.
- EMERGENCY SUPPLY indicator (15H14)- This indicator lights
up as soon as the ship’s main supply not available.
- CONTROL VOLTAGE indicator (13H2)- This indicator lights up
as soon as the ship’s control centre and the main power
switch allow electric supply.
- OFF-ON SPACE HEATER (17S7)- This indicator lights up when
the power supply to the heating elements is switched on.
- HIGH OIL TEMPERATURE WARNING INDICATOR (13H7) - This indi-
cator lights up when the oil temperature at the hydraulic
power pack is too high.
- LOW OIL TEMPERATURE WARNING INDICATOR (13H8) - This indica-
tor lights up when the oil temperature at the hydraulic
power pack is too low (<5°C).
- FAILURE MOTOR TRIPPED INDICATOR (13H11) - This indicator
lights up when a motor circuit breaker has released.
- FAILURE HEATER INDICATOR (13H3) - This indicator lights up
when the fuse for heating has switched off.
- FAILURE MINIMUM OIL LEVEL INDICATOR (13H10) - This indica-
tor lights up when the oil level in hydraulic power pack is
under normal level.
- OPERATION INDICATOR (14H5) - This indicator lights up
(green colour) when the hydraulic motor is running.

For further details see the electric circuit diagrams.

2.6.3 TRANSFORMER BOX

The transformer box is placed on power pack under deck and is
of the enclosure class IP54.
The following controls/alarms are situated on the transformer
box:
- BATTERY CHARGER SUPPLY indicator (11H1)- This indicator
lights up as soon as the power supply for the battery
charger is switched on.
- HEATER 42V TRAVERSE (11H11) - This indicator lights up as
soon as the power supply for the traverse heater is
switched on.
- SPACE HEATER 230V INDICATOR (11H6) - This indicator lights
up when the power supply for sheave bolts and winch heating
elements is switched on.

For further details see the electric circuit diagrams.

d-i davit international-hische gmbh pg.28
Manual
system free-fall system for lifeboat D-FH.

2.6.4 CONTROL STATION

The control station is placed in protection box on davit
track close to the foundation and is heated.
The following controls/alarms are situated on the control
station:
- EMERGENCY STOP BUTTON (S0.0), with this button the electric
supply to the hydraulic can be disconnected.
- HOISTING BUTTON (S1), it is a push button for activating
the craft handling winch. With this winch it is possible to
hoist a lifeboat with a full complement of persons.
- LOWERING BUTTON (S2), it is a push button for activating
the craft handling winch. With this winch it is possible to
lower a lifeboat with a full complement of persons.
- CYLINDER-OUT BUTTON (14S7.1), it is a push button for acti-
vating the hydraulic cylinders. It is possible to turn out
a lifeboat with a full complement of persons.
- CYLINDER-IN BUTTON (14S7.2), it is a push button for acti-
vating the hydraulic cylinders. It is possible to turn in a
lifeboat with a full complement of persons.
- READY FOR OPERATION indicator(13H16), this indicator en-
lights (blue colour)when the davit is ready for operation.
- HYDRAULIC-OFF FAILURE indicator (S16), this indicator en-
lights when a hydraulic failure does not allow operation of
the davit (thermistor, motor protection switch, oil level
min., oil temperature high).
- HYDRAULIC-ON indicator (S17), this indicator enlights as
soon as the hydraulic motor is running.

2.6.5 The control station contains a stand by heating element

connected to the 230 V circuit via a thermostat(19S11). The
thermostat is set to activate the heating element in case the
temperature in the control station drops below -20°C. The
thermostat is pre-set by d-i no further adjustment by the
customer is necessary.
Adjustement:
- Open the thermostat case by removing the three screws
- Dial setpoint = Heating off
Particular attention should be paid both to the higher tol-
erances which apply to the scale end and the fact that the
switch off value is not visible.
The scale value can be adjusted by turning the hexagonal
nut at the base of the axle.
- Close case with the three screws

2.6.6 HEATING ELEMENTS

The heating elements are predicted for:
- sheave bolts on davit arm (2 pcs. – 230V)
- sheave bolts on the traverse (2 pcs. – 24V)
- oil heater gearbox (2 pcs.)
- hydraulic motor on winch
- winch housing
- protection box for control station
d-i davit international-hische gmbh pg.29
Manual
system free-fall system for lifeboat D-FH.

3 WINCH SYSTEM

3.1 BASIC WINCH DESCRIPTION

For a better comprehension of the text below, it is advisable to unfold

the accompanying illustration sheet "kinematic diagram of winch"
included further in this manual.

Basically, the winch comprises a:

- wire rope coiling gear; the drum or barrel

- speed reducer gear
- motor power unit

3.1.1 DRUM
To coil, accommodate, or unwind the necessary wire rope
falls, the winch is equipped with a single drum, the shaft of
which is splined to the output stage reduction gear and sup-
ported in roller type bearings.

3.1.2 SPEED REDUCER GEAR

The speed reducer gear employs an appropriate conventional
gear train.

3.1.3 MOTOR POWER UNIT

The motor power unit is represented by a hydraulic motor, al-
lowing speeds from 0 to the maximum required. The motor
drives the conventional gear train through a multi-disc hy-
draulic brake. The brake is released during lowering as well as
during hoisting.
The motor has been equipped with a load valve, preventing ac-
cidents in the case of line-malfunctioning. The same valve is
used for the releasing the hydraulic brake.

3.2 FUNCTIONAL DESCRIPTION

The individual modes of operation are as follows:

3.2.1 HOISTING BY HYDRAULIC POWER

Hydraulic motor rotation enacted by actuation of the control
button on the control stand results in a corresponding drum ro-
tation.

3.2.2 LOWERING BY HYDRAULIC POWER

This procedure is identical to the procedure as described in
paragraph 3.2.1 .
d-i davit international-hische gmbh pg.30
Manual
system free-fall system for lifeboat D-FH.

4 RECOMMENDED LUBRICANTS

For the recommended oil and grease lubricants, please see the accompany-
ing list made up in compliance with recommendations by the oil companies
mentioned therein. For obvious reasons, the list cannot be exhaustive;
equivalent products by other recognised companies are acceptable as
well.

Lubricants have been developing unceasingly; it is advisable to consult

your lubricant supplier, in particular whenever operation at extremes of
temperature should be envisaged.

5 MAINTENANCE

In this chapter the required maintenance will be described; it is to

be executed by the ship's crew. The maintenance procedure shall be
performed in accordance to Solas Edition 2001, Chapter III, Regula-
tion 20.

LAUNCHING APPLIANCES SHALL BE SERVICED AND TESTED AT

RECOMMENDED INTERVALS IN ACCORDANCE WITH SOLAS AND THE LSA-
CODE. A THOROUGH EXAMINATION, INCLUSIVE WINCH BRAKE TEST,
NOTE: AT INTERVALS NOT EXCEEDING 5 YEARS MUST BE ACCOMPLISHED.

Even though the interval of checking and maintaining the parts of a

davit system depends on the frequency and way of operation, we have
tried to give an estimation of the required intervals.

For this safety system it is compulsory to have any repair performed

by skilled labour only.

Please bear in mind that the use of “No Name” spare parts exclude any
warranty from our side. It will be dangerous also in that way that a
proper function may not be ensured.

WHEN STARTING ANY MAINTENANCE, INSPECTION OR REPAIR AT THE

DAVIT OR WINCH, ALWAYS BE CERTAIN THAT BOAT IS NOT HANGING
IN THE WIRE ROPE FALLS.
d-i davit international-hische gmbh pg.31
Manual
system free-fall system for lifeboat D-FH.

5.1 MAINTENANCE GROUP 1, DAILY INSPECTION

5.1.1 VISUAL INSPECTION

Visual inspection of the complete davit system should be
done, to ensure operational readiness.

ICE ACCERTION SHOULD BE REGURARLY REMOVED FROM THE LIFEBOAT

AND DAVIT TO ENSURE EASE OF LAUNCHING WHEN REQUIRED.

AN ICING REMOVAL MALLET SHOULD BE AVAILABLE IN THE VICINITY

OF THE DAVIT.

Operation of heating elements (see electric) to be checked.

5.2 MAINTENANCE GROUP 2, ONE WEEK SERVICE

5.2.1 HYDRAULIC FLUID LEVEL

The level of the hydraulic fluid in the tank, which is situ-
ated under deck, should be checked every week. For this purpose
a dipstick has been installed on the tank. The level has to be
at the upper mark in home position. In this connection the hy-
draulic connections and components should be checked for
leakage.

5.2.2 AIR CONDITIONER CHECK

The hydraulic power pack can breathe, thus allowing water va-
pour and solid contaminants to enter. Temperature fluctua-
tions in the tank will cause this water vapour to condense.

HYDRAULIC OIL MUST BE KEPT FREE FROM CONTAMINATION AND

WATER!!
WATER IN OIL CAN LEAD TO CONSIDERABLE MECHANICAL DAMAGE OF
THE HYDRAULIC COMPONENTS AND TO MALFUNCTIONING OF THE
SYSTEM!!

To prevent this, air conditioner is built on power pack.

The uptake of moisture can be observed by the

change in colour of the indicator granules in
the air conditioner.

They turn from orange (active) to very dark

green (replace).

The air conditioner is completely replaceable.

d-i davit international-hische gmbh pg.32
Manual
system free-fall system for lifeboat D-FH.

5.3 MAINTENANCE GROUP 3, THREE MONTHS SERVICE

5.3.1 DAVIT (greasing)

The davit sheaves and pivot points have been provided with
maintenance free, pre-lubricated bushes, running on stainless
steel shafts. So: a special maintenance of these turning parts
is not necessary.

The hydraulic cylinders are executed with spherical ball

bearings, which require additional greasing.

All thread ends, required for adjustment purposes (as sea

lashing turnbuckles, must always be kept greased.

Special attention should be given to the items as mentioned

below:
- hand operated valves of the hydraulic system

5.3.2 WINCHES (greasing)

All lubrication points must be lubricated by means of a high
pressure grease gun at regular intervals.

5.3.3 WIRE ROPES (greasing)

Rope maintenance encompasses re-lubrication and if necessary
prior cleaning; furthermore inspection and adjustment of all
rope reeving components like drums, sheaves etc.
Re-lubrication should employ grease or dressing that is com-
patible with the manufacturers´ lubricant. The coating must
be such as not to impair the visual inspection of the ropes
surface. The applied grease should be slightly heated before-
hand. Ropes must be renewed in case of deterioration.

5.3.4 SHEAVES
Sheaves must be turning freely and truly and the grooves
should seat the rope properly. A damaged sheave must be ex-
changed.

5.3.5 OIL LEVEL CHECK

The oil level in the gearbox of the winch must be checked.
For this purpose a level plug has been installed on the winch
housing.

5.3.6 DRAIN OFF CONDENSATE

Due to temperature variation it is necessary to drain off the
separate condensate. For this procedure open the drain plug
on the bottom of the tank as long as water escapes.
d-i davit international-hische gmbh pg.33
Manual
system free-fall system for lifeboat D-FH.

5.4 MAINTENANCE GROUP 4, ONE YEAR SERVICE

5.4.1 HYDRAULIC SYSTEM (oil change)

The complete quantity of hydraulic oil must be changed once a
year. During the changing of the oil, the following should be
kept in mind:
DIRT IS POISON TO EVERY HYDRAULIC INSTALLATION!!
So also the filter element should be changed.
Only absolute and perfect cleanliness will ensure a faultless
operation of the equipment. The quantity of oil has been indi-
cated on the drawing of the power pack.

5.4.2 WINCHES (oil change)

All winches have the tooth wheels running in an oil bath; the
oil must be changed once a year. Before filling the gearbox
with new oil, it should be cleaned thoroughly with scouring
oil and the sediment removed from the bottom of the gearbox.
The gearbox has been provided with a drain plug on the lower
side. The quantity of oil has been indicated on page 4, under
"LAUNCHING APPLIANCE DATA".

5.4.3 INSTALLING/CHANGING OF WIRE ROPES

Special attention is drawn to the necessity for checking that
the wire rope falls are running on the drum from the correct
side. This must be checked before unreeving the rope falls.
When wedge cases are used for connecting the wire rope, the
wire rope which is under strain, must form one line with one
side of the wedge casing.
The windings on the drum must be laid tightly against each
other, they should not be laid over one another.
It is advisable to unreeve the wire ropes each 30 months and
turned end for end before they are reeved anew (if possible).
Reference is made to regulation 20.4.1 of Chapter III, SOLAS
2001.
It is also advisable to cut 30 cm (1 foot) from each wire
rope before they are reeved anew.

5.4.4 PAINTING
When repainting the davits, winches etc., it frequently hap-
pens that a further coat of paint is applied over the previ-
ous one, so that the free clearances between moving parts are
entirely filled up with paint.
Consequently in the long run the moving parts seize up.
When repainting special attention must therefore be paid to
the prior removal of the old coat of paint near the moving
parts, at least on the dangerous areas. The grease nipples
and the breathers must never be painted, to avoid a stoppage
in the grease channel and malfunctions during bleeding.
A red circle should be painted around each grease nipple.

5.4.5 SPARE PARTS

Periodically the presence of spare parts should be checked.
For this purpose our recommendation can be found in the chap-
ter "SPARE PARTS".
d-i davit international-hische gmbh pg.34
Manual
system free-fall system for lifeboat D-FH.

5.5 MAINTENANCE GROUP 5, FIVE YEAR SERVICE

For this five year service it is compulsory to have any repair

performed by skilled labour only. If there are any questions please
contact our spare part and service department.

5.5.1 WIRE ROPES

Ropes must be renewed at intervals of not more than 5 years,
if not done before due to deterioration.

5.6 HOSE LINES (REPLACING)

Hose lines should be replaced in regularly intervals, even if no defects

are visible. At least after 5 years the hose lines should be renewed.
For this procedure the date of manufacturing which is marked on the hose
cover is decisively. The way of marking depends on the producer, for
example:
3Q12 = 3rd Quarter of 2012
25/09/2012 = the date directly

5.7 LOG FOR INSPECTIONS AND MAINTENANCE

The above mentioned maintenance procedures as well as the required

inspections have to been logged up. For this reason the table below
will show an example which can be used.

date inspection remarks name position

(maintenance group)

6 SPARE PARTS

For this lifesaving system the following spare parts were recommended
and they should be on stock in the ship.

Pos. Qty. Unit d-i Part No. Description

1 2 pc 0211049 roller G4-6861, polyamide
2 18 pc 0205680 hexagon screw M10x20, A4
breather plug 3/8" (filling plug)
3 1 pc 0208242 stainless steel
4 2 pc 0207652 shaft seal 130-160-12AS
5 2 pc 0211048 shaft seal 52-72-8
 DSME/KOREA/TEEKAY - LUBRICATION OIL CHART (d-i ref. No. 1995-11-A/C-1)
HULL: H2430 BRAND: see G3-6333
All following mentioned gears, winches and hydraulic items are delivered without lubricant.

MACHINERY APPLICATION TYPE REMARK

(MODEL)
POINT CAPACITY
Free Fall Boat Handling System winch-gear box 40,0 l winch gear box check all three months
D-FH.100 (1x) greasing plan G1-6273 change every year
Free Fall Boat Handling System hydraulic unit (power pack) 300,0 l hydraulic pump check weekly
D-FH.100 (1x) hydraulic diagram Hy1995A-D (powerpack) change every year
Free Fall Boat Handling System grease nipples 01-07 - slewing gear and three months service
D-FH.100 (1x) greasing plan G1-6273 nipple lubrication
Free Fall Boat Handling System wire rope lubrication - wire rope lubrication three months service
D-FH.100 (1x) greasing plan G1-6273
Combined Rescue Boat / Liferaft winch-gearbox 4,0 l toothgear check all three months
handling system D-CRm.R.23/4,0 greasing plan G2-4871 change every year
Combined Rescue Boat / Liferaft winch-freewheel 0,1 l FILLED BY MAKER
handling system D-CRm.R.23/4,0 greasing plan G2-4871 lifetime lubricated
Combined Rescue Boat / Liferaft hydraulic unit (power pack) 180,0 l hydraulic pump check weekly
handling system D-CRm.R.23/4,0 hydraulic diagram Hy1995C-D (powerpack) change every year
Combined Rescue Boat / Liferaft grease nipples 01-07 - slewing gear and three months service
handling system D-CRm.R.23/4,0 greasing plan G2-4871 nipple lubrication
Combined Rescue Boat / Liferaft wire rope lubrication - wire rope lubrication three months service
handling system D-CRm.R.23/4,0 greasing plan G2-4871

d-i davit international-hische gmbh Rev.0 2018-09-18 page 1 of 1 pages

Ship: H2430 Ref.No: S 24420 Date: 18.09.2018
IMO: 9750725 d-i comm.: 1995/11AC

Pos. Qty. Unit Part # Description

D-FH.100
1 2 pc 211049 roller G4-6861, polyamide
2 18 pc 205680 hexagon screw M10x20, A4
breather plug 3/8" (filling plug)
3 1 pc 208242 stainless steel
4 2 pc 207652 shaft seal 130-160-12AS
5 2 pc 211048 shaft seal 52-72-8
D-CRm.R.02
6 1 pc 204213 RC-block sheavehouse A4-4043 black
7 28 pc 202357 hexagon screw M10x30, A4
8 1 pc 211942 shaft seal 130-170-12
centrifugal brake lever (250) A3-4534
compl. With pads and rivets (2 pcs.= 1
9 1 set 200600 set)
stop brake size 1 consisting of:
1 pc. Brake lining plate
10 1 set L0200372 2 pcs. Pressing plates
11 1 pc 209 angular contact ball bearing 7210 B
12 1 pc 114 bush 115/100x32, C361
13 1 pc 205 shaft seal 100-120-12
14 3 pc 202358 hexagon bolt M10x110, A4
15 1 pc 201515 lock nut KMT 5
16 1 pc 200371 circlip 30x1,5
17 1 pc 1109 angular contact ball bearing 7206 B
18 1 pc 206 needle roller bearing K30
19 1 pc 214 freewheel bearing NSS40
20 1 pc 199 shaft seal 45-72-8AS
21 1 pc 204 shaft seal 85-120-12AS
22 1 pc 211943 cabinet heater 50W
23 1 pc 211941 shaft seal 55-65-8 A
proximity switch NO polar execution -
24 1 pc 211047 60° C
Rev. 2018-04-16

Authorised service stations

Area Company

World-wide
World-wide d-i davit international-hische GmbH
Sandstrasse 20
27232 Sulingen
Phone: +49 4271 9344 0
Fax: + 49 4271 9344 339
E-mail: aftersales@di-hische.de

Africa
Tunesia, Algeria, Morocco CMR Tunisia Ship Repairs
Avenue des Caroubiers
PO Box 10
7050 Menzel Bourguiba
Phone: +216 72418590
Fax: +216 72418354
E-mail: cmrtun@cmrtunisie.com

South Africa BOSSS Lifeboat + Lifesaving Services

10 Kobe Road
Bayhead
Durban, Zn S-4001
Phone: +21 31 206 2498
Fax: +21 31 205 9443
E-mail: life@bosss.co.za

America
North

Canada DERA Maritime Services

17 Chouinard
J5Y3S6 Repentigny, QC
Phone: +1 514 9193530
Fax: +1 450 9324530
E-mail: yan@deramaritime.com

USA, Canada Breakwater International

327 Lecouvreur Avenue
90074 Los Angeles, CA
Phone: +1 310 518 1718
Fax: +1 310 549 1122
E-mail: california@bkwint.com

USA, Canada Full Sail Marine Group LLC

220 SW 30th Street
33315 Fort Lauderdale, FL
Phone: +1 954 616 8870
Fax: +1 954 616 8897
E-mail: kboylan@fullsailmarine.com
Rev. 2018-04-16

USA, Caribbean, Mexico Survival Systems International

931 Industry Road
P.O. Box 1567
70062 Kenner, Louisiana
Phone: +1 504 469 4545
Fax: +1 504 466 1884
E-mail: CarlosS@ssinola.com

USA, Mexico Breakwater International

8320 Millet Rd.
Houston, Texas 77012
Phone: +1 832 582 7547
Fax: +1 832 582 7588
E-mail: texas@bkwint.com

USA Extinval USA

8920 Lawndale St. Suite A
77012 Houston, Texas
Phone: +1 713 923 6200
Fax: +1 713 923 6202
E-mail: info@extinvalusa.com

USA High Seas Trading Company - California

1312 W. Esther street
90813 Long Beach, California
Phone: +1 562 983 2050
Fax: +1 562 983 2053
E-mail: leif@highseasusa.com

South

Argentina, Uruguay IDP Sociedad Anónima

José Colombres 2353
1605 Munro, Buenos Aires
Phone: +54 11 4721 0077
Fax: +54 11 4762 6336
E-mail: a.diriscio@idpsa.com.ar

Argentina, Uruguay Uruguayan Marine Safety Ltd.

Arturo Lezama 2228
11800 Montevideo
Phone: +598 2 9244938
Fax: +598 2 9246025
E-mail: weserve@ums.com.uy

Brazil Atrac
Rua Santa Isabel, number 31
Jardim Gramacho, Duque de Caxias
20051-170 Rio de Janeiro
Phone: +55 21 3504 2150
Fax: +55 21 3504 2155
E-mail: atrac@atrac.net
Rev. 2018-04-16

Brazil Metalock Brasil Ltda.

Rua Visconde do Rio Branco
20/26, 11013-030 Santos,SP
Phone: +55 13 3226 4686
Fax: +55 13 3226 4088
E-mail: santos@metalock.com.br

Chile, Ecuador, Peru Chile Services Management S.A.

1001 Francia Av.
Valparaiso - Chile
Phone: +56 32 210766
Fax: +56 32 228995
E-mail: info@csmchile.com

Colombia, Central America Panama Lifeboat Services, S.A. Or

Caribbean Villa Zaita, Urb. La Rotonda,
Calle Conexion Casa 163.B PoBox.
0819-05525 El Dorado - Panama
Phone: +507 2375580
Fax: +507 2375589
E-mail: csmpanama@gmail.com

Asia
Bahrain Solas Marine Services Co. LLC
PO Box 10738
Diplomatic Manama
Phone: +973 17 466859
Fax: +973 17 465583
E-mail: sivaprasad@solasmarine.com

China, Hong Kong Dickson Technical Services Ltd.

2nd Floor, Feoso Building
877 Lai Chi Kok Road
Kowloon, Hong Kong
Phone: +852 2415 0513
Fax: +852 2416 7678
E-mail: dicksong@dicksonship.com.hk

India Cargo Gear Services (I.) Pvt. Ltd

Plot No. 10 Opp.Sant Janaben Municipal Market
Godapdev Cross Road No. 1, Off E.S. Patanwala Marg.
400033 Mumbai
Phone: +91 2223770451
Fax: +91 2223780538
E-mail: cgs@cargogearservices.com

Japan Mansei Inc.

1575-17, Houjyouji, Ekiya-Cho
Fukuyama City
Phone: +81 84 972 2121
Fax: +81 84 972 9292
E-mail: info@mansei.net
Rev. 2018-04-16

Japan Mizuno Marine Co., Ltd.

Head Office
1-12-15 Meishinguchi Toyonaka-City
561-0841 Osaka
Phone: +81 66863 5233
Fax: +81 6 6863 5029
E-mail: info@mizuno-marine.co.jp

Malaysia TechnoFIBRE International Sdn. Bhd.

No. 10, Jalan Cempedak 3
Taman Kota Masai
81700 Masai
Johor
Phone: +60 7 255 2181
Fax: +60 7 255 2585
E-mail: sales@technofibremalaysia.com

Russia - South Odissey-ship-service Co. Ltd.

133 Kalinina str.
690012 Vladivostok
Phone: +7 4232275229
Fax: +7 4232275826
E-mail: ods05@mail.ru

Singapore Fassmer Singapore Pte. Ltd

18 Boon Lay Way, #02-143
Tradehub 21
609966 Singapore
Phone: +65 8498 6330
Fax: +65 6564 6465
E-mail: service@fassmer.sg

Singapore Fibre Craft Asia Pte Ltd

111, North Bridge Road
#27-01 Peninsula Plaza
179098 Singapore
Phone: +65 6243 9495
Fax: +65 6863 1476
E-mail: info@fibrecraftasia.com

Singapore TechnoFibre (S) Pte. Ltd.

42A Penjuru Road, #06-00, Lobby 1
609164 Singapore
Phone: +65 6266 1412
Fax: +65 6266 1435
E-mail: sales@technofibre.com

Singapore Viking Life-Saving Equipment Pte. Ltd.

14 Loyang Way 4
507601 Singapore
Phone: +65 64249200
Fax: +65 64249210
E-mail: YA@viking-life.com
Rev. 2018-04-16

South Korea BNS Co.

Dongsan Bldg. 2F,87
Daeri-ro, Beomseo-eup, Ulju-Gun
44921 Ulsan
Phone: +82 52 249 1100
Fax: +82 52 249 1150
E-mail: bnskorea@empas.com

South Korea Wooree MEK

Ocean Tower, Room No. 823
760-3, Woo1-Dong
Haeundae-Ku
612-021 Busan
Phone: +82 51 740 5921
Fax: +82 51 740 5924
E-mail: wooreemek2@wooreemek.com

Taiwan Fine Ocean Marine Industrial Corp.

No.300, Xing-Wang Rd
Qian-Zhen Dist.
80665 Kaohsiung
Phone: +886 781 55 967
Fax: +886 781 56 579
E-mail: office@fineocean.com.tw

United Arab Emirates Solas Marine Services Co. LLC

Bahrain, Iran, Iraq, Kuwait, Dubai Investment Park
Oman, Qatar, Saudi Arabia PO Box 25445
Dubai
Phone: +971 4 279 1300
Fax: + 971 4 279 1200
E-mail: info@solasmarine.com

United Arab Emirates, TechnoFIBRE Dubai

Bahrain, Iran, Iraq, Kuwait, Techno Fibre Middle East Marine Services FZE
Oman, Qatar, Saudi Arabia Unit Q4-71
Sharjah Airport International Freezone
Sharjah
Phone: +971 6 5579225
Fax: +971 6 5579234
E-mail: lifeboat@technofibredubai.com

Australia
Australia, New Zealand RFD (Australia) Pty. Ltd
59-63 Redwood Drive
3172 Dingley Village, Vic
Phone: +61 3 9558 0055
Fax: +61 3 9558 0455
E-mail: help@survitecgroup.com
Rev. 2018-04-16

Australia TechnoFIBRE Australia Pty. Ltd.

Unit 2 / 125 Barrington St.
P.O. Box 1561
Bibra Lake WA 6965
Phone: +61 89494 2622
Fax: +61 89494 2766
E-mail: sales@technofibreaustralia.com

New Zealand Denray Marine Services Ltd.

96 Kerwyn Ave
East Tamaki, 2013
Auckland
Phone: +64 92748080
Fax: +64 92748787
E-mail: sales@denray.co.nz

Europe
Bulgaria, Romania Jambo Ltd.
Fire, Rescue and Safety Services
20 Atanas Moskov blvd.
9009 Varna
Phone: +359 52576767
Fax: +359 52576768
E-mail: jambo@jambobg.com

Estonia, Sweden Viking Life Saving Equipment Estonia AS

Helgi tee 3
Peetri küla, Rae vald
75312 Harjumaa
Phone: +372 606 9390
Fax: +372 606 9399
E-mail: jz@viking-life.com

Estonia Mereabi Ltd.

Lume 7
10416 Tallinn
Phone: +372 660 2320
Fax: +372 660 2249
E-mail: info@mereabi.ee

Finland, Estonia, Sweden Viking Life Saving Equipment OY Finland

Pääskykalliontie 13
21420 Lieto
Phone: +358 2489500
Fax: +358 24895011
E-mail: tl@viking-life.com

France Macor e.u.r.l.

Grand Port Maritime de Marseille
Enceinte Portueire - Porte 4 - Local Macor- CS 30024
13344 Marseille Cedex 15
Phone: +33 491 116350
Fax: +33 491 116359
E-mail: lsaservice@macor.fr
Rev. 2018-04-16

France ACEBI
Z.I. Route d'Anetz
44150 Saint-Herblon
Phone: +33 240 980 006
Fax: +33 240 980 089
E-mail: service@acebi.com

Germany d-i davit international- hische GmbH

Sandstrasse 20
27232 Sulingen
Phone: +49 4271 9344 0
Fax: + 49 4271 9344 339
E-mail: aftersales@di-hische.de

Great Britain, Ireland Survival Systems International UK Ltd.

Viking Road, Gapton Hall Industrial Estate
Great Yarmouth
NR31 0NU Norfolk
Phone: +44 1493 659411
Fax: +44 1493 655425
E-mail: info@ssiuk.net

Greece, Cyprus Internaftiki A.E.B.E.

Ships Supplies and Services
6, Alipedou Str.
185 31 Piraeus
Phone: +30 210 4126997
Fax: +30 210 4127566
E-mail: service@internaftiki.gr

Italy BG Safe Srl.

Via delle Cateratte 86/88 int. 16
57122 Livorno
Phone: +39 0586 839588 / AOS: +39 348 2620 503
Fax: +39 0586 205004
e-mail: baronetto@lifeboatservices.com

Italy Viking Life Saving Equipment Italia srl

Via delle Pianazze 170
19136 La Spezia
Phone: +39 0187 981322
Fax: +39 0187 982499
E-mail: RGIA@viking-life.com

The Netherlands, Belgium North Sea Davit and Lifeboat Services

Edisonweg 48
3404 LD Ijsselstein
Phone: +31 30 262 7117
Fax: +31 30 262 4038
E-mail: info@nsdls.nl

The Netherlands, Belgium Proofload (Services) B.V.

Hoogheuvelstraat 113
5349 AM Oss
Phone: +31 412 646974
Fax: +31 412 652340
E-mail: info@proofload.com
Rev. 2018-04-16

Norway Viking Life-Saving Equipment Norge AS

Idrettsvegen 110, Straume Næringspark
5353 Straume (Bergen)
Phone: +47 81500325
Fax: +47 56326110
E-mail: service-bergen@viking-life.com

Poland Strahlmann Ltd.

Narzedziowa Str. 43,
70-807 Szczecin
Phone: +48 914722105
Fax: +48 914722125
E-mail: service@strahlmann.pl

Portugal Repforn
Zona Industrial Ligeira II
Lote 1130
7520-309 Sines
Phone: +351 269878370
Fax: +351 269878388
E-mail: repforn@repforn.pt

Russia - North Production Departy Co. Ltd.

27 Kanonersky island
198184 St. Petersburg
Phone: +7 812 5754539
Fax: +7 812 7469699
E-mail: mail@prodep.ru

Russia - North Techservice Ltd.

North Division
12, Portoviy Proezd
183038 Murmansk
Phone: +7 921 9490893
Fax: +7 812 3275556
E-mail: ts@sp.ru

Russia - North - West Port-Service Ltd.

Kievskaya Str. 21 b
236039 Kaliningrad
Phone: +7 401 2577117
Fax: + 7 401 2577117
E-mail: ps@ps-kld.ru

Russia - South Fatom Ltd.

(Caspian Sea) Admiral Nachimov st. 70
414028 Astrakhan
Phone: +7 8512305776
Fax: +7 8512305774
E-mail: ftm@fatom.ru
Rev. 2018-04-16

Russia - South Techservice Ltd.

South Division
93, 13th Linia str.
344019 Rostov-on-Don
Phone: +7 921 9490842
Fax: +7 812 3275556
E-mail: ts@sp.ru

Russia - South Alanar LLC

5/1, Anapskoe highway
353501 Temryuk, Krasnodar Region
Phone: +7 9054570500
Fax: +7 8614851857
E-mail: office@alanar.su

Spain Viking Life-Saving Equipment Iberica S.A.

Avda. del Puero, nave 6.21
Pol. Ind. La Menacha
11205 Algeciras (Cádiz)
Phone: +34 956 573 240
Fax: +34 956 571 422
E-mail: aspa@viking-life.com

Spain, Canary Islands Inprecasa

Ctra. La Cuesta - Taco, km. 1,4
38320 La Laguna
Tenerife
Phone: +34 617 447 142
Fax: +34 922 650 387
E-Mail: inprecasa@inprecasa.com

Turkey Mugesan A.S.

Bagdat Caddesi No:67/5
34724 Feneryolu / Istanbul
Phone: +90 216 411 5466
Fax: +90 216 386 4248
E-mail: info@mugesan.com

Ukraine Marko Ltd.

23/5 Protsenka Str.
65031 Odessa
Phone: +380 487335544
Fax: +380 487051237
E-mail: vkoval@markogroup.com