COMPACT SENSORS

S62
The most complete universal sensor
in a compact 50x50 mm housing
• Sensors with red, infrared LED or LASER emission

• Background suppression from 3 cm to 2 m

• Polarized retroreflective up to 20 m

• Multivoltage 24-240Vac/24-60Vdc with Relay output

• NPN/PNP output NO-NC configuration

APPLICATIONS
-Processing and Packaging machinery
-Conveyor lines, material handling

S62
Through beam 0…25 m
Retroreflective (on R2 reflector) 0,1…13 m
0,1…8 m
Polarized retroreflective
0,3…20 m (class 2 LASER)
short 0…900 mm, long 0...2000 mm
Diffuse proximity
0…900 mm (class 2 LASER)
short 30…300 mm
medium 60…600 mm
long 60…1200 mm
Background suppression
very long 200...2000 mm
short LASER 30…150 mm (class 2 LASER)
long LASER 50…350 mm (class 2 LASER)
Vdc 10…30 V
Power supply Vac
Vac/dc 24/240 Vac/24…60 Vdc
PNP •
NPN •
Output NPN/PNP •
relay •
other
cable •
Connection connector •
pig-tail
Approximate dimensions (mm) 18x50x50
Housing material ABS
Mechanical protection IP67

100
 TECHNICAL DATA
10 ... 30 Vdc (mod. S62…2/5)
Power supply
24…240 Vac/ 24…60 Vdc (mod. S62…1)
Ripple 2 Vpp max. (mod. S62…2/5), 10% max. (mod. S62…1)
30 mA max. (mod. S62…2/5)
Consumption (output current excluded)
3 VA max. (mod. S62…1)
red LED 640 nm (mod. S62-PA…A/B/C/G/M01/M05/M11/M15)
Light emission IR LED 880 nm (mod. S62-PA…M21/M25/M31/M35)
red Laser 645…665 nm (mod. S62-PL)
Setting sensititivity adjustment trimmer
Operating mode mono-turn light/dark trimmer (mod. S62…RX/PN)
yellow OUTPUT LED
Indicators
green STABILITY LED, POWER LED (S62…G)
PNP or NPN N.O./N.C. (mod. S62…PP/NN); NPN/PNP (mod. S62…PN);
Output
electromechanical SPDT 250 Vac/30 Vdc (mod. S62...RX)
Output current 100 mA max. (mod. S62…2/5), 2 A max. (mod. S62...1)
Saturation voltage 2 V max. (mod. S62…2/5)
25 ms (mod. S62…1)
1,5 ms (mod. S62…M3x)
1 ms (mod. S62…2/5-F/G/M2x)
Response time
500 µs (mod. S62-PA…2/5-A/B/C/M0x/M1x)
200 µs (mod. S62-PL…B/C/M11)
140 µs (mod. S62-PL…M01)
20 Hz (mod. S62…1)
330 Hz (mod. S62…M3x)
500 Hz (mod. S62…2/5-F/G/M2x)
Switching frequency
1 kHz (mod. S62-PA…2/5-A/B/C/M0x/M1x)
2,5 kHz (mod. S62-PL…B/C/M11)
3,5 kHz (mod. S62-PL…M01)
Connection M12 4-pole connector, 2 m Ø 4 mm cable vers., 2 m Ø 5 mm cable vers.
Dielectric strength 500 Vac 1 min., between electronics and housing
TEChNICaL DaTa
Insulation resistence >20 MΩ 500 Vdc,DIMENSIONS
between electronics and housing
Mechanical protection
S62-PL-M01… S62-PL-M11… 50 IP67 18
0.75

Ambient light rejection 10 … 30 VDC 42 4.7

1.1

According to EN 60947-5-2
2 Vpp max.
Vibrations 0.5 mm amplitude, 10 … 55 Hz frequency, for each axis (EN60068-2-6)
Shock resistence 30 mA max 11ms (30G) 6 shock for every axis (EN60068-2-27)
PNPHousing
or NPNmaterial
N.O. / N.C.; 30 VDC max. (short-circuit protection) ABS
2

100 mA (overload and overvoltage protection)

Lens material
RECEIVER
PMMA window, policarbonate lens
2V
Operating temperature -10 … 55 °C 18.2
42
50

140 s 200 s
3.5Storage
kHz temperature 2.5 kHz -20 … 70 °C EMITTER
18x45°

ED LASER ( =Weight 40 g max. conn. vers., 90 max. cable vers.

15.5

645…665nm): Class 2 EN 60825-1, Class II CDRH 21 CFR PART 1040.10

mission: pot. max  5mW; pulse duration = 5s; frequency = 14KHz (mod. M01) / 10KHz (mod. M11)
ChNICaL60DaTa
mm 150 mm DIMENSIONS
DIMENSIONS
< 0.2 mm (at 60 mm) < 0.4 mm (at 150 mm)
16

S62…M1-PP/PN/NN
30…150 mm S62…M2-PP/PN/NN S62…M3-PP/PN/NN
50…350 mm 50 18
Background suppression
0.75

10 … 30 VDC
turn distance adjustment trimmer 6-turn distance adjustment trimmer 42 4.7
1.1

DIMENSIONS 11 6 14 M12
<2 4Vpp
% (seemax. DETECTION DIAGRAM)
<1% Ø15
OUTPUT40 LED mA max.
(YELLOW)
TEChNICaL DaTa
50 / POWER ON LED (GREEN) 18 Laser version DIMENSIONS
0.75

42 4.7
1.1

S62-PL-M01…
-10 … 55 °C S62-PL-M11… 11 50 18
N N.A./N.C. 30 VDC / S62...PN: -20 NPN/PNP; 30 VDC max (short-circuit protection)
0.75

… 70 °C 10 … 30 VDC
2

42 RECEIVER 4.7
1.1

100 mA (overload
500 Vacand 1 min.,overvoltage protection)
between electronics and housing 2 Vpp max. 6.18 18.4
18.2

2 V between electronics and housing

 Vdc,
42
50

>20 M 500 30 mA max

s According to EN 60947-5-2
1 ms 1,5 ms
2

0.5 mm amplitude, 10 … 55 Hz frequency, PNP or NPN forN.O.

each / N.C.; 30 VDC max. (short-circuit protection)
axisRECEIVER
(EN60068-2-6)
EMITTER
18x45°

Hz 500 Hz 330 Hz
2

100 mA (overload and overvoltage protection) RECEIVER

15.5

11 ms (30 G) 6 shock for each axis (EN60068-2-27)

18.2

60 nm) INFRARED (880  2 Vnm)

42
50

10.7
18.2

DISTANCE ADjUSTMENT TRIMMER

ABS
42
50

15x15 mm (at PMMA400140mm) s PC lens

window; 200x200 mm (at 2000 mm)200 s POSITION INDICATOR
EMITTER OUTPUT LED
18x45°

3.5IP67
kHz 200…2000 mm 2.5 kHz mm EMITTER
18x45°

60…600 mm 60…1200 mm
16

POWER ON LED
15.5

15.5

RED LASER ( = 645…665nm):

M12 4-pole connector Class 2 (recommended
EN 60825-1, target
Class 400x400mm)
II CDRH 21 CFR PART 1040.10
adjustment trimmer Pulsed/ Timer
emission: adjustment
pot.40max trimmer
5mW; pulse
g. max. (S62…M05/M15/M25/M35)
duration = 5s; frequency = 14KHz (mod. M01) / 10KHz (mod. M11)
SaFETY PRECaUTIONS
S62…M01/M11-PN) 60 mm - 150 mm 11 6 14 M12
SETTING < 0.2 mm (at 60 mm) Led version
All the electric and mechanical safety regulations have to be respected during
< 0.4 mm (at 150 mm)
16

16

< 12 % < 25 % < 30 % sensor functioning. Ø15

values): 30…150 mm 50…350 mm
<5% 4-turn distance adjustment trimmer % distance adjustmentThe
< 206-turn sensor has
trimmer
to be
TIMER protected against mechanical damage.
ADjUSTMENT
Apply theTRIMMER
labels supplied in a visible position11
(mod.M05/M15/M25/M35) near6 the laser emission
14 beam. M12
STABILITY
black): LED (GREEN) Rotate 6trimmer inLED
11 OUTPUT an14(YELLOW) /DETECTION
POWER
< 4 % (see direction
anticlockwise M12
ON
until LEDLED
DIAGRAM)
yellow (GREEN)
turns OFF DARK/LIGHT
tance required.
TRIMMER 14 11 CaBLE VERSION Ø15
-10and … green
55 °CLED ON: condition where background < 1 % Ø15 is outside operating (S62-M01/M11-PN)
yellow LED OFF and TIMER ADjUSTMENTrange (C status OUTPUT of positionLED
indicator).
(YELLOW) / POWER ON LED (GREEN) 6.18 18.4
-20 … 70 °C
TRIMMER (mod.M05/M15/M25/M35)
-10 … 55 °C 11
500 VAC 1 min., between electronics
DARK/LIGHT
TRIMMER 14 and
11 housing
CaBLE Cable version
-20 … 70VERSION
°C
>20 M 500 VDC, between electronics500 and housing 6.18 18.4
Ø4

(S62-M01/M11-PN)
Vac 1 min., between electronics and housing
According to 6.18
EN 60947-5-2 18.4
>20 M 500 Vdc, between C electronics and housing
m amplitude, 10 … 55 Hz3.frequency, for each axis (EN60068-2-6)
Setting and control According to EN 60947-5-2
6 shock Rotate trimmer
0.5axis in an anticlockwise
mm (EN60068-2-27)
amplitude, 10 … 55 Hz direction untilfor
frequency, the indicator
each reaches
axis (EN60068-2-6) 10.7 DISTANCE ADjUSTMENT TRIMMER
Ø4

w LED 11 and
ms green
(30 G)LED for each
an intermediate point between
11 ms (30 G) position
6 shock for A and
each C.axis (EN60068-2-27) Do not stare directly into the laser beam!
n indicator). ABS POSITION INDICATOR
ABS Do not point the OUTPUT
laser LED
beam towards people! 10.7 mm
DISTANCE ADjUSTMENT TRIMMER
PMMA window; PC lens PMMATRIMMER
window; PC lens
STABILITY LED STABILITY
Eye irradiation (S62…M2/M3)
superior toLED/
0.25 seconds is dangerous. POSITION
PleaseINDICATOR
refer to the
10.7 DISTANCE ADjUSTMENT POWER ON LED (S62…M0/M1)
Class 2 Standard (EN60825-1). OUTPUT LED
IP67 IP67
mm

POSITION INDICATOR These sensors can not be used for safetyPOWER ON LED
applications!
2 m cable  4OUTPUTmm /LED M12 4-pole connector M12 4-pole connector mm

nded to be connected to a
If position
STABILITY LED STABILITY
(S62…M2/M3)
Class
LED/ A and C are close to each other,
2 transformer orfunction
class 2correctly
power
leave trimmer on position C.
40 g. max.supply TIMER FUNCTION (S62…M05/M15/M25) SaFETY PRECaUTIONS
POWER ON LED The sensor
(S62…M0/M1) is now ready to and in stable conditions. EX-II-3-D T6
90 g. max. cable vers. / 40 g. max. connector SETTING vers. The timer function
Temperature allows
class:
All thetoelectric
adjustand T6
the (<85°C)
output deactivation
mechanical delay
safety regulations havewhen the
to be respected during
object is outsideMax. Power sensor functioning.
consumption:
the detection area. The 800 mW
delayat 30 Vdc
extends the output activation 101
front of the sensor: TIMER FUNCTION (S62…M05/M15/M25)
nting The sensor has to be protected against mechanical damage.
allowing theMax. slowerInternal capacitance:
interface systems to 100 pF shorter pulses.
detect
SETTING Apply the labels supplied
Internal inductance: in a visible position near the laser emission beam.
negligible
The timer function allows to adjust the output deactivation
Rotate trimmer delay when
in an anticlockwise the until yellow LED turns OFF
direction
front of the sensor
object is at the distance
outside required. area. The and
the detection delay green LED ON:
extends the condition where background is outside operating
output activation
operating distance. emission Indicators:
Storage presence.
Storagetemperature:
temperature: S62…a/B/C/F: This indicator OUTPUT has a scale LEDnumbered (YELLOW) -201/…
from STABILITY
-20
to 70 6… °C
that °CLED
70allows (GREEN)
the precise
Please refer clockwise
to clockwise
“SETTING” paragraph for the correct useIndicators: S62…G: of the suppression POWERdistance ON LED
LIGHT
Please LIGHT
referMODE:
to MODE:
“SETTING” rotation
rotation
paragraph for the correct use SENSIBILITY TRIMMER (aDJ.) (S62..a/B/C/F)S62…G:adjustmentPOWER ON VAC, LED (GREEN)on the(GREEN)entire operating range.
procedure.
DARK DARK
MODE:MODE:counter-clockwise
counter-clockwiserotation.
rotation. Dielectric
Dielectricstrength:strength: Please refer to
500 500
“SETTING”
VAC, Mono-turn 1 min
paragraph
1formin
between between
sensitivity
the correct
electronics
use
electronics
adjustment
procedure.
and and
housing
trimmer housin
procedure. A mono-turn
Adjustment: trimmer adjusts the sensitivity and the sensor
DaRK/LIGhT
WARNING:
DaRK/LIGhTWARNING: the TRIMMER
TRIMMER the
maximum
maximum(S62..RX/PN)
mechanical
(S62..RX/PN) mechanicalrotation
rotation
range
range Insulating
of Adjustment:
of the the Insulating resistance:
resistance: >Mono-turn
20>M, 20 M,
500
Mono-turn
sensitivity
5VDC
00light/dark
VDC adjustment
between between electronics
trimmer
trimmer
electronics and and
(S62..RX/PN) housing hous
The LIGHT/DARK operating distance. Mono-turn light/dark trimmer (S62..RX/PN) S62
The trimmer
trimmer
is 240°.
LIGHT/DARK Do mode
is mode
240°. Do
not not isforce
force
is selected
selected
over over using
of the
using of the amaximum
mono-turn
maximum
a mono-turn and andPlease
Ambient Ambient
Operating
refer
lighttemperature:
to
light
rejection:
rejection:
“SETTING” paragraph for the correct use
according
Indicators:
INSTaLLaTION according -10to EN …to55 60947-5-2
EN °C60947-5-2
trimmer.
minimum
minimumpositions.
positions. Operating temperature: -10 … 55 °C S62 Ro
trimmer. Vibrations:
Vibrations:
Storage
procedure. temperature: 0.5 mm 0.5 mm amplitude,
amplitude, 10 … 1055 …Hz 55-20frequency,
Hz … frequency,
70 °C for every for every axis axis(EN60 (E
tur
LIGHT MODE: clockwise rotation Storage temperature: The sensor can be positioned by -20 … 70 °C
means
LIGHT MODE: clockwise rotation Shock Shock
resistance:
Dielectric resistance:
strength: (S62..RX/PN) 11 ms 11holes
500 (30
msVAC, G)
(30 6G)
Adjustment:
1 shock
min 6 shock for every
between forelectronics
every
axis axis (EN60068-2-27)
(EN60068-2-2
and housing
CONNECTIONS
CONNECTIONS
COMPACT SENSORS
DARK MODE: counter-clockwise rotation. DaRK/LIGhT
Dielectric strength:TRIMMER of the three housing’s
500 VAC, 1 min
using
between
two
electronics and housing
screws (M4x25 or longer, 1.5 Nm
DARK MODE: counter-clockwise rotation.
WARNING: the maximum mechanical rotation range of theInsulating The Housing Housing
LIGHT/DARK
Insulating material:material:
mode is selected usingmaximum
resistance: a mono-turn > 20 M,Operating 500 with VDCtemperature: ABSABS
between electronics and housing
DC
WARNING: DC
models:
models:
the maximum mechanical rotation range of the Lens resistance:
Lens
material:
material: > 20tightening
M, 500torque) VDCPMMA
PMMA between
window, window,electronics
policarbonate
policarbonateand lens housing lens
trimmer is 240°. Do not force over of the maximum andtrimmer. Ambient light rejection: washers.
Storage according temperature: to EN 60947-5-2
trimmer is 240°. Do not force over of the maximum and Ambient light
Mechanical rejection:
Mechanical
LIGHTVibrations: protection:
MODE: clockwise rotation protection: Various orientable fixing according
brackets to
to EN 60947-5-2
IP67 IP67
minimum positions. 0.5themmsensor amplitude, 10
Dielectric… 55 Hz frequency,
strength:for every axis (EN60068-2 for every axis (EN6
minimum positions. S62-Pa-2/5-PN
S62-Pa-2/5-PN Vibrations:
DARK MODE:
Connections: counter-clockwise rotation. 0.5
Connections:
ease
mm
2 mavailable mamplitude,
2cable cable 4
 (please mm 4 10mm
/ms
positioning
M12 …/ M12 55 Hz the
4-pole
are
frequency,
Shock resistance: 11 refer(30 G) 4-pole
to connector
6 shock connector
for every axis (EN60068-2-27 2 m 2cable m cable 5
CONNECTIONS CONNECTIONS
CONNECTIONS Shock resistance:
WARNING: the maximum mechanical rotation
Housing material: VDC range
accessories
VDCmodels: 11
models:ms
ofthey (30
thethey
listed areG) 6
in intended Insulating
shock
the intended
are general for resistance:
every
to betoconnected beABSaxis (EN60068-2-27)
connected to a to Class a Class 2 transfo
2.Ba
2 tra
Re
trimmer material:
is 240°. Do not force over of the 2maximum catalogue). and Ambient light rejection:
Housing power
2 power supply. supply. VAC is VACmodels: models: ABSthe
these thesedevices devices shall ofshall
be connected
be connectto yel
DC models: Lens material: The operating distance PMMA
measured window,
from policarbonate
front surface the lens
sensor
DC models: minimum
Lens positions.
material: supply
optics. supply orPMMA
or system,including Vibrations:
window,
system,including policarbonate
filters filters
or air-gaps,
or air-gaps,lens of overvoltage
of overvoltage cat
ULMechanical
requirements:
UL requirements: protection: The (“load
M12 connector beShock resistance: IP67
Mechanical protection: (“load level level –can
– secondary secondary oriented
circuit atoftwo
IP67
circuit a of different
protected
a protected positions using
utilityutility the
transformer”),
transforme
VDC MODELS S62-Pa-2/5-PN S62-Pa-2/5-PN Connections: CONNECTIONS 2 m cable
specific
control control 
fastening 4 M12
mm
spring /and
atCONNECTOR
M12 4-pole
rotating
Housing connector
the block
material:
to 180°. 2 m cable 
Connections: 2 m cable  4over-voltages
mmover-voltages
/ M12 4-pole the at maximum
the maximum
connector “rated “rated
impulse
2 impulse
m cable withstandwithstand
 5 mm volt
DC models: VDC models: 1.2KV they
1.2KV andareand intended
with
Lens with
a
CONNECTIONS to
short-circuit
a
material: be connected
short-circuit power power to alimit
limit atClass
max at 2
max trans
500VA 50
VDC models: they are intended to be connected to a Class 2 transformer
Weight:NPN/PNP version 2 power 90supply. VAC models: these/ 40devices shall be connected Ro
Through beam emitter Weight: 2 power M12 supply.
connector g.90max.
VAC g.models:
max.
cable cable
versions
Mechanical
these versions protection:
devices /g.40max.
shall g.be max.connectors
connectors
connected version
to ave po
S62-Pa-2/5-PP/NN
S62-Pa-2/5-PP/NN S62-2/5-G
S62-2/5-G S62-Pa-2/5-PN supply or system,including filters or air-gaps, of overvoltageturc
UL requirements: supply or system,including filters or air-gaps, of overvoltage categor
Connections: 2 m
UL requirements: (“load level SETTINGS
– SETTINGS
secondary circuit of a protected utility transformer”
(“load level – secondary circuit of a protected utility transformer”), suita VDC
control over-voltages at the maximum “rated impulse withstand vo
S62..a/B
S62..a/B setting: setting: Position
Position
the sensor
the sensorcontrol
and and over-voltages
reflector reflector onat
on opposite thesides.
opposite maximum sides.
Turn “rated
Turn
the sensitivity
the impulse
sensitivity withstand
trimmer trimmer voltage 2p
1.2KV and with a short-circuit power limit attomax maximu
to500V
max
Find Find
the points
the pointswhere wherethe yellow
the yellowLED LED(OUT) (OUT)1.2KV
in both
in and
both with
vertical aand
vertical short-circuit
and
horizontal power
horizontal positions limit
positions atand max and
fix500VA.
the
fix senso
the s
Weight: 90 g. max. cable UL versions / 40 g. max. connectors versi
requirements:
Weight:
betweenbetween these these
points.points.
Optimum
Optimum operation
operation 90
is obtained g. max.
is obtained when cable
whenbothversions
both
LEDs LEDs / 40switch
switch g.ON. max. If connectors
ON. necessary,
If necessary, versions
reduce reduce
sens (“
S62-Pa-2/5-PP/NN S62-2/5-G
S62-Pa-2/5-PP/NN S62-2/5-G trimmer,
trimmer, in order in order to detect
to detect veryverysmallsmalltargets. targets. In order In orderSETTINGS
to improveto improve alignment,
alignment, repeat repeatthe procedure
the procedure co
detaileTh
de
progressively
progressively reducingreducingthe sensitivity.
the sensitivity. SETTINGS is o

aC aCmodels:
models: S62..a/B
S62..C S62..Csetting:setting:
setting: Position
Position
Position
the the
sensor
the sensor
sensorand and
and
turn reflector
turn
the sensitivity
the on opposite
sensitivity trimmer sides.
trimmer at Turn
minimum:
at minimum:the sensitivity
the yellow
the yellow trimmer
LED LED
is OFF to
is maxim
OFF
S62..a/B setting: Position the sensor and reflector on opposite sides. Weight: Turn the sensitivity trimmer to maximum.
Find themode).
S62-Pa-2/5-PP/NN points where thetarget
yellow LED the(OUT)
S62-2/5-G inTurnboth vertical and horizontal positions and fix yellow
the yello
sen
S62-Pa-1-a/B/C/F
S62-Pa-1-a/B/C/F S62-Pa-1-G
S62-Pa-1-G Find (litgh
the (litgh
mode).
points Place
where Place
the yellow
the target
the opposite
LED opposite
(OUT) sensor.
intheboth sensor. vertical Turn
the andsensitivity
thehorizontal
sensitivity trimmer trimmer
positions clockwise clockwise
and fix until theuntil
the the
sensor inLE
between
turnsthese
turns
ON (Target
ONthese points.
(Targetdetected Optimum
detected state, state,operation
pos.A).
pos.A).
Remove is obtained
Remove the target,
the whentarget, both
the yellow the LEDs
yellowLED switch
LED
turns ON.
turns
OFF. IfOFF.
necessary, reduce se
between points. Optimum operation is obtained when both LEDs switch ON. If necessary, reduce sensitivity
trimmer,
Turn Turn
the in trimmer
trimmer
the order toclockwise
clockwise detect very small targets. In turns
order(Background
to improve alignment, repeat the procedure deta
trimmer, in order to detect very until
smalluntil
thetargets.
yellow
the yellow LED
In LED
turns
order toON ON
improve (Background
alignment, detected
S62..a/B setting:
detected
repeat state,
the state,
Position
pos.B).
procedurepos.B).
the sensor detailed and ab re
Theprogressively
The
trimmertrimmer reducing
reaches reaches the sensitivity.
progressively reducing the maximum maximum
sensitivity. if theif background
the background is not is detected.
not detected. TurnTurn the trimmerthe trimmer in intermediate
in intermediate positionpositiC
aCVAC aCMODELS
models:
models: RELaY RELaY S62..C
S62..C
betweenbetween
setting:
setting:
thePosition
two Position
the positions
twothe positionsthe
A and
sensor
sensor
A
andand
B. turn
The and
B. the
The turn
green greenthe
LEDLED
sensitivity
sensitivity
must must
be ON.
trimmer
trimmer
be
Find
ON.
atbetween
minimum:
the
at points
minimum:
thesethe yellow
where
points.
the
LED
the
yellow
Optimum
yellow
LED is
is OFFoperation is
LED
OFF (OU
(litgh mode). Place the target opposite theopposite
sensor. Turnsides. the sensitivity trimmer clockwise until the yellow
S62-Pa-1-a/B/C/F S62-Pa-1-G (litgh S62…F/G
mode).S62…F/GPlacesetting: setting:
the Position
target Position
the sensors
opposite thethesensors on
sensor. on Turnoppositethesides. Turn
sensitivity Turn
the sensitivity
trimmer
trimmer, the in sensitivity
clockwise
order trimmer trimmer
toOFF. until
detect to themaximum.
to
very maximum.
yellowsmallLED Find
targe Fith
S62-Pa-1-a/B/C/F S62-Pa-1-G
Through beam emitterturnsthe turns
ONyellow
the ON
yellow
(Target
(Target
LED LED
detected(OUT)detected
(OUT)
state,
state,
is switched
is switched
pos.A).
pos.A).
ON
Remove ON Remove
and and OFF OFF
the target,
the
in both target,
intheboth
vertical
yellow
the
vertical yellow
and
LED and LED
horizontal
turns
turns
horizontal
OFF. positions,positions, and and
fix thefix sens
the s
Turn the trimmer clockwise until the yellow LED turns ON (Backgroundprogressively detected reducing state, the sensitivity.
pos.B).
aCbetween
Turn the
The
between
trimmer
models: these these
points.
clockwise
trimmerreduce reaches
points.
Optimum
until Optimum operation
the yellow
maximum
operation
LED isturns
if using
the
obtained
is ONobtained when
(Background when
bothboth LEDs
detected
S62..C
LEDs
switch
Turnsetting:
switch
state,ON.pos.B). ON.
Position the sensor and turn
If necessary,
The trimmer If necessary,
reaches maximum reduce
sensitivity
sensitivity
if theusing thebackground
background trimmer,
the is trimmer, is
notindetected.
notorder
order
in detected.
to detect
Turnto detectthevery the small
very
small
trimmer
trimmer
targets. in intermediate
targets.
in intermediate
position M

RELaY between the two positions A and B. The green LED must be ON. (litgh mode). Place the target position oppositeC,the s
RELaY betweenInS62-Pa-1-a/B/C/F
order
In order
the to improve
two to improve
positions alignment,
alignment,
A and B. repeat S62-Pa-1-G
The repeat the procedure
green the procedure
LED must detailedbe ON. detailed above above whilst whilst
progressively
progressively reducing reducing the sensitivi
the sen
S62…F/G setting: Position the sensors on opposite sides. Turn turns theON (Target detected
sensitivity trimmer to state,
maximum.pos.A).Find Rem
S62…F/G setting: Position the sensors on opposite sides. Turn the Turn sensitivity thehorizontaltrimmer
trimmer to maximum.the
clockwise Find the po
the yellow LED (OUT) is switched ON and OFF in both vertical and positions,until and fixyellow the sen L
the yellow LED (OUT) is switched ON and OFF in both vertical andThe horizontal
trimmer positions,
reaches and fix the sensor in
between these points. Optimum operation is obtained when both LEDs switch ON. maximum if the backgr
between these points.RELaY Optimum operation is obtained when both LEDs switch
between ON.
If necessary, reduce sensitivity using the trimmer, in order to detect verythe smalltwotargets.positions A and B. The gree
If necessary, reduce sensitivity using the trimmer, in order to detect very S62…F/G small targets.
In order to improve alignment, repeat the procedure detailed above whilstsetting:progressively Position reducingthe sensors the sensit on
In order to improve alignment, repeat the procedure detailed above whilst progressively
the yellow LED (OUT) reducing the sensitivity.
is switched ON and
between these points. Optimum operation is
If necessary, reduce sensitivity using the trim
In order to improve alignment, repeat the pro

INDICATORS AND SETTINGS

S62-B S62-M WITH TIMER S62-M W/O TIMER

A
B A B D A B D

C C E E

a Output status LED D Distance adjustment trimmer

B Stability LED or Power ON LED E Geared numeric scale

(laser vers.)
F M12 connector output
C Timer adjustment trimmer
G Cable output

102
detection diagrams of models with led emission

cm
R2 R5

% difference object distance

White 90% /
Black 6% White 90% /
m Grey 18%

mm

Setting distance

Polarized retroreflex 30 ... 300 mm background suppression

% difference object distance

% difference object distance

White 90% /
White 90% /
Black 6%
Black 6%

White 90% /
White 90% /
Grey 18%
Grey 18%
mm
mm

Setting distance Setting distance

60 ... 600 mm background suppression 60 ... 1200 mm background suppression

300 S62-M0
% difference object distance

White 90% /
Black 6%
600 S62-M1
White 90% /
Grey 18% 1000 1200 S62-M2

2000 2200 S62-M3

Setting distance
0 500 1000 1500 2000 2500 (mm)
200 ... 2000 mm background suppression

R5 9 10

R2 8 8,5

0 2 4 6 8 10 (m)

Recommended operating distance

Maximum operating distance

103
COMPACT SENSORS
detection diagrams of models with laser emission

mm mm
R2

Spot diameter
m m

Distance
Laser polarized retroreflex Light spot dimension - Laser polarized retroreflex
% difference object distance

White 90% / % difference object distance White 90% /

Black 6% Black 6%
White 90% / White 90% /
Grey 18% Grey 18%

mm mm

Setting distance Setting distance

30 ... 150 mm laser background suppression 50 ... 350 mm laser background suppression

Reflector operating distances (m)

R1 R2 R6 R7 / R20 R8
150 S62-M01
0.3 … 16 0.3 … 20 0.4 … 22 0.3 … 22 0.2 … 2
350 S62-M11
The use of the RT3970 reflecting tape is suggested.
0 100 200 300 400 (mm)

R2 20 21

R7 22 23

0 5 10 15 20 25 (m)

Recommended operating distance

Maximum operating distance

104
MODEL SELECTION AND ORDER INFORMATION
OPTIC FUNCTION EMISSION CONNECTION OUTPUT MODEL ORDER No.
2m Cable PNP/NPN S62-PA-2-A01-PN 956211240
LED
Retroreflective M12 Connector PNP/NPN S62-PA-5-A01-PN 956211310
(red 640nm)
Vac relay Relay S62-PA-1-A01-RX 956211180
PNP/NPN S62-PA-2-B01-PN 956211250
2m Cable
PNP S62-PA-2-B01-PP 956211010
LED NPN S62-PA-5-B01-NN 956211020
(red 640nm) M12 Connector PNP/NPN S62-PA-5-B01-PN 956211320
Polarized retroreflective
PNP S62-PA-5-B01-PP 956211000
Vac relay Relay S62-PA-1-B01-RX 956211190
NPN S62-PL-5-B01-NN 956211100
LASER M12 Connector
PNP S62-PL-5-B01-PP 956211110
NPN S62-PA-2-C01-NN 956211420
2m Cable PNP/NPN S62-PA-2-C01-PN 956211260
PNP S62-PA-2-C01-PP 956211380
LED
NPN S62-PA-5-C01-NN 956211500
(red 640nm)
M12 Connector PNP/NPN S62-PA-5-C01-PN 956211330
Short diffused proximity PNP S62-PA-5-C01-PP 956211460
Vac relay Relay S62-PA-1-C01-RX 956211200
NPN S62-PL-2-C01-NN 956211440
2m Cable
PNP S62-PL-2-C01-PP 956211400
LASER
NPN S62-PL-5-C01-NN 956211520
M12 Connector
PNP S62-PL-5-C01-PP 956211480
NPN S62-PA-2-C11-NN 956211430
2m Cable PNP/NPN S62-PA-2-C11-PN 956211270
PNP S62-PA-2-C11-PP 956211390
LED
Long diffused proximity NPN S62-PA-5-C11-NN 956211510
(red 640nm)
M12 Connector PNP/NPN S62-PA-5-C11-PN 956211340
PNP S62-PA-5-C11-PP 956211470
Vac relay Relay S62-PA-1-C11-RX 956211210
NPN S62-PA-2-F01-NN 956211450
2m Cable PNP/NPN S62-PA-2-F01-PN 956211290
PNP S62-PA-2-F01-PP 956211410
Through beam receiver - NPN S62-PA-5-F01-NN 956211530
M12 Connector PNP/NPN S62-PA-5-F01-PN 956211360
PNP S62-PA-5-F01-PP 956211490
Vac relay Relay S62-PA-1-F01-RX 956211220
2m Cable S62-PA-2-G00-XG 956211300
LED
Through beam emitter M12 Connector - S62-PA-5-G00-XG 956211370
(red 640nm)
Vac relay S62-PA-1-G00-XX 956211230
PNP/NPN S62-PA-2-M01-PN 956211280
2m Cable
PNP S62-PA-2-M01-PP 956201841
NPN S62-PA-5-M01-NN 956201811
LED
PNP/NPN S62-PA-5-M01-PN 956211350
Background suppression (red 640nm)
M12 Connector PNP S62-PA-5-M01-PP 956201831
(short distance)
NPN S62-PA-5-M05-NN 956201801
PNP S62-PA-5-M05-PP 956201821
NPN S62-PL-5-M01-NN 956211120
LASER M12 Connector
PNP S62-PL-5-M01-PP 956211130
2m Cable PNP S62-PA-2-M11-PP 956201891
NPN S62-PA-5-M11-NN 956201861
LED
PNP S62-PA-5-M11-PP 956201881
Background suppression (red 640nm) M12 Connector
NPN S62-PA-5-M15-NN 956201851
(medium distance)
PNP S62-PA-5-M15-PP 956201871
NPN S62-PL-5-M11-NN 956211140
LASER M12 Connector
PNP S62-PL-5-M11-PP 956211150
2m Cable PNP S62-PA-2-M21-PP 956201940
NPN S62-PA-5-M21-NN 956201910
Background suppression
PNP S62-PA-5-M21-PP 956201900
(long distance) M12 Connector
NPN S62-PA-5-M25-NN 956201930
LED PNP S62-PA-5-M25-PP 956201920
(infrared 880nm) 2m Cable PNP S62-PA-2-M31-PP 956211050
NPN S62-PA-5-M31-NN 956211060
Background suppression
PNP S62-PA-5-M31-PP 956211070
(very long distance) M12 Connector
NPN S62-PA-5-M35-NN 956211080
PNP S62-PA-5-M35-PP 956211090

105
COMPACT SENSORS
ACCESSORIES

ACCESSORIESACCESSORIES
ACCESSORIES
St-504 St-504 St-5020
St-504 St-5020 St-5020 St-5021 St-5021 St-5021
2 2 2 4.5 4.5 4.5

20

20

20

19

19

19
Ø 4.1 Ø 4.1 Ø 4.1
2

28

28

28
30°

30°

30°
26,5 26,5 26,5
Ø 4.4 Ø 4.4 Ø 4.4

9 9 9
30° 30° 30°
Ø 4.3 Ø 4.3 Ø 4.3 20 20 20

5
Ø 5.1 Ø 5.1 10 Ø 5.1 10 10

Ø 4.1 Ø 4.1 Ø 4.1 Ø 4.4 Ø 4.4 Ø 4.4

Ø 4.3 Ø 4.3 Ø 4.3
50

50

50
8

8
20° 20° 20°
Ø 4.1 Ø 4.1 Ø 4.1

12

12

12
40

40

40
Ø 4.4 Ø 4.4 Ø 4.4

21

21

21
Ø 4.3 Ø 4.3 Ø 5.3 Ø 4.3 Ø 5.3 Ø 5.3
Ø 4.4 Ø 4.4 Ø 4.4

2
2

2
10° 10° 10°
3 0° 3 0° 3 0°
28 28 28
16.5 16.5 16.5 35° 35° 35°

88 St-5054 88 St-5054
88 St-5054
62 St-505362 St-5053
62 St-5053

23

23

23
2

2
41

41

41

42 42 42
21

21

21

R15 R15 R15

2

9 9 9 Ø 6.5 Ø 6.5 Ø 6.5

44 10° 44 10° 44 R5 10° R5 R5
R16 R16 R16 R20 R20 R20
5

Ø 4.3 Ø 4.3 Ø 4.3

Ø 4.3 Ø 4.3 ØØ
4.35.1 Ø 5.1 Ø 5.1
Ø 4.3 Ø 4.3 Ø 4.3
Ø 4.1 Ø 4.1 Ø 4.1R15 R15 R15
26

56
50

26

56
50

26

56
50
Ø 4.3 Ø 4.3 Ø 4.3
50

50

50
8

Ø 4.1 Ø 4.1 20° 20° 20° Ø 4.3 Ø 4.3 Ø 4.3

Ø 4.1
Ø 4.3 Ø 4.3 Ø 4.3
R20 R20 R20
R40 R40 R40
Ø 6.5 Ø 6.5 Ø 6.5
Ø 5.3 Ø 5.3 Ø 5.3
R15 R15 R15
R16 Ø 4.3 R16 R16
Ø 10°
4.3 Ø 4.3 10° 10°
10 10 R5 10 R5 49 R5 49
30° 49 30° 30°
mm mm mm
11 11 11
73 73 73

Joint-62: as ST-5054
Joint-62:
with jointed
as ST-5054
support withasjointed
Joint-62: support
ST-5054 with jointed support

ACCESSORY SElECtION
ACCESSORYAND
SElECtION
ORDERSElECtION
ACCESSORY INFORMAtION
AND ORDER ANDINFORMAtION
ORDER INFORMAtION
ST-5018 ST-5019
DESCRIPtION DESCRIPtION DESCRIPtION MODEl MODEl
ORDER N° MODEl ORDER N° ORDER N°
Ø 23 mm prismatic reflector
Ø 23with
mmØprismatic
31 mmØ support
reflector with Ø 31reflector
23 mm prismatic mm support
with Ø 31 mm support R1 R1 S940700023 R1 S940700023 S940700023
Ø 48 mm prismatic reflector
Ø 48with
mmØprismatic
63 mmØ support
reflector with Ø 63reflector
48 mm prismatic mm support
with Ø 63 mm support R2 R2 S940700048 R2 S940700048 S940700048
36 x 55 mm prismatic reflector
36 x 55with
mm40.5
prismatic
x 60
36 mm
xreflector
55supportwith 40.5 reflector
mm prismatic x 60 mmwith
support R6
40.5 x 60 mm support R6 95A151350 R6 95A151350 95A151350
38 x 40 mm microprism 38
reflector
x 40 mm
withmicroprism
51 x 38
60.7 mm
reflector
x 40 mmsupport
with 51 x 60.7
microprism mmwith
reflector support R7
51 x 60.7 mm support R7 95A151360 R7 95A151360 95A151360
9.7 x 19 mm microprism9.7
reflector
x 19 mm
withmicroprism
13.89.7
x 23 mm
reflector
x 19 mmsupport
with 13.8 reflector
microprism x 23 mmwith
support R8
13.8 x 23 mm support R8 95A151370 R8 95A151370 95A151370
Ø 48 mm prismatic reflector
Ø 48with
mmØprismatic
63 mmØ support
reflector with Ø 63reflector
48 mm prismatic mm support
with Ø 63 mm support R20 R20 95A151090 R20 95A151090 95A151090
protection bracket with jointed
protection
support
bracket protection
with jointedbracket
supportwith jointed support JOINT-S62 JOINT-S62
95ACC2430
JOINT-S62 95ACC2430 95ACC2430
fixing bracket fixing bracket fixing bracket ST-504 ST-504
95ACC2820 ST-504 95ACC2820 95ACC2820
fixing bracket fixing bracket fixing bracket ST-5020 ST-5020
95ACC5330ST-5020 95ACC5330 95ACC5330
fixing bracket fixing bracket fixing bracket ST-5021 ST-5021
95ACC5340ST-5021 95ACC5340 95ACC5340
protection bracket protection bracket protection bracket ST-5053 ST-5053
95ACC2410ST-5053 95ACC2410 95ACC2410
protection bracket protection bracket protection bracket ST-5054 ST-5054
95ACC2420ST-5054 95ACC2420 95ACC2420

UNI EN ISO9001 UNI EN ISO9001 UNI EN ISO9001

The company endeavours Thetocompany

continuously
endeavours
improve
The to
and
companycontinuously
renew its products;
endeavours improve and
for this
renew
to continuously reason
its products;
improvetheand
technical
for this
renew data
itsreason
and contents
the for
products; technical
of this
this data
catalogue
reason andtechnical
the contents
may undergo
of this
data catalogue
andvariations
contentsmay undergo
of this variations
catalogue may undergo variations
without prior notice. For without
correct prior
installation
notice. and
Foruse,
withoutcorrect
thenotice.
prior installation
companyForcanandguarantee
use,
correct the company
only and
installation the data
can guarantee
use, indicated
the companyinonly
the the
caninstruction
data indicated
guarantee manual insupplied
only the the instruction
data with themanual
indicated products.
in supplied with
the instruction the products.
manual supplied with the products.

www.datalogic.com
www.datalogic.com
www.datalogic.com

106
 MODEL DESCRIPTION ORDER No.
ST-5018 protective bracket 95ACC5310
ST-5019 protective bracket 95ACC5320
ST-5020 mounting bracket 95ACC5330
ST-5021 mounting bracket 95ACC5340
ST-504 mounting bracket 95ACC2820
ST-5053 protective bracket 95ACC2410
ST-5054 protective bracket 95ACC2420
JOINT-S62 protective bracket with jointed support 95ACC2430

CABLES

TYPE DESCRIPTION LENGTH MODEL ORDER No.

3m CS-A1-02-G-03 95A251380
5m CS-A1-02-G-05 95A251270
4-pole, grey, P.V.C.
7m CS-A1-02-G-07 95A251280
Axial M12 Connector
10 m CS-A1-02-G-10 95A251390
2m CS-A1-02-R-02 95A251540
4-pole, P.U.R.
5m CS-A1-02-R-05 95A251560
3m CS-A2-02-G-03 95A251360
5m CS-A2-02-G-05 95A251240
4-pole, grey, P.V.C.
7m CS-A2-02-G-07 95A251245
Radial M12 Connector
10 m CS-A2-02-G-10 95A251260
2m CS-A2-02-R-02 95A251550
4-pole, P.U.R.
5m CS-A2-02-R-05 95A251570
3m CS-A2-12-G-03 95A251400
Radial M12 Connector
with LED 4-pole, grey, P.V.C. 5m CS-A2-12-G-05 95A251350
(for PNP N.O. sensors)
10 m CS-A2-12-G-10 95A251370
3m CV-A1-22-B-03 95ACC1480
5m CV-A1-22-B-05 95ACC1490
Axial M12 Connector 10 m CV-A1-22-B-10 95ACC1500

4-pole, shielded, black, 15 m CV-A1-22-B-15 95ACC2070

P.V.C. 25 m CV-A1-22-B-25 95ACC2090
3m CV-A2-22-B-03 95ACC1540
Radial M12 Connector 5m CV-A2-22-B-05 95ACC1550
10 m CV-A2-22-B-10 95ACC1560
3m CS-A1-02-U-03 95ASE1120
5m CS-A1-02-U-05 95ASE1130
4-pole, U.L., black, P.V.C. 10 m CS-A1-02-U-10 95ASE1140
Axial M12 Connector
15 m CS-A1-02-U-15 95ASE1150
25 m CS-A1-02-U-25 95ASE1160
Connector- not cabled CS-A1-02-B-NC G5085002
4-pole, black
Radial M12 Connector Connector- not cabled CS-A2-02-B-NC G5085003

107