Laser type
Scanning Laser Range Finder
Range Sensor
UXM-30LN-P FDA approval
Possible to detect black car!
Light
weight,1kg or less!
Easy to install it at the higher place!
Possible
to set ON/OFF-delay timer
Possible to cancel the quick motion objects.
Minimum
detectable range configuration
Don't detect dust etc.
Minimum
detectable width configuration
Don't detect small animals or dead leaves.
Possible
to register 16 kinds of area and to changeover by
outer input
Malfunction output and 3 detecting output are provided.
Safety
design
FDA Laser Class 1,Intrinsically safe!
System structure
Applications
Vehicle detection at multistory parking lot
Detectable area
Detectable area 190
760 steps
Step angle 0.25
0.1 to
30m
Scanning direction
UXM-30LN-P
Specifications
Kinds
Model No.
Power source
Current consumption
Light source
Principle
Detectable object
Scanning range
Scanning accuracy
Angular Resolution
Scanning angle
Scanning time
Interface
Input
Indication lamps
54
Detection area setting type (parallel type)
UXM-30LN-P
10 to 30VDC
During operating: 500mA or less when 10/12VDC,250mA when 24VDC
When staring up: 2A or less when 10VDC,1.5A or less when 12VDC
Semiconductor laser diode =905nm (FDA approval, Laser safety class 1)
Time of ight (pulse system)
6m: 10mm, 10m: 20mm, 30m: 130mm (Min. objects against the distance)
0.1 to 301 (Black diffuse reection 10%, 500mm500mm)
3,000lux or less0.1 to 10m: 50mm (500500mm or more, white paper)2
100,000lux or less0.1 to 30m: 100mm (500500mm or more, white paper)2
Step angle: 0.25(360/1,440 steps)
190
50msec/scan (Motor speed:1,200rpm)
USB2.0 (Full Speed, 12Mbps for area setting)
Trouble output, detection output 1, 2, 3 (Nch open-drain output 30VDC 100mA or less)
Area input 1, 2, 3, 4 (total 16 patterns)
Power lamp (green), Operating lamp (orange): Lights up when detecting, blinks when troubled
Connection
Ambient temperature/ humidity
Insulation resistance
Vibration resistance
Impact resistance
Protective structure
Life
Noise
Case materials
Weight
Cable 2m, USB: connector (Binder 09-0431-81-04)3
-10 to +50 (-25 to +75when stored), 85%RH or less, not icing, not condensing
10M 500VDC megger
Double amplitude 1.5mm, 10 to 55Hz, each 2 hour in X, Y and Z directions
196m/s2, each 10 time in X, Y and Z directions
IP64 (IEC standard)
5 years (motor life, vary depending on use conditions)
25dB or less
Front of case: Polycarbonate, back of case: aluminum
Approx.800g (excluding cable)
S
Range Sensor
1. Verify the actual performance of the sensor under the intended working environment.
2. Measurement under direct interference light is not assured.(sunlight etc.)
3. The other side:Binder 99-0430-10-04.(option) USB cable for UXM series.(as an option)
This is not safety device.
Note
Connection
External dimension
Input/ output circuit
View field
angle 190
COM
1k
4.7k
IN
Load
OUT
120
108
4-5.4
Indication lamps
COM
63.5
Center of
light-projecting
132
146
50.5
Signals
10 to 30VDC
0V
Area input 1
Area input 2
Area input 3
Area input 4
Trouble output
Detection output 1
Detection output 2
Detection output 3
COM for I/O (+COM)
COM for output (-COM)
NC
NC
NC
NC
For power source /
output
(57)
interface cable
Cable colors
Brown
Blue
Green
Yellow
Purple
White/yellow
Orange
Black
White
White/blue
Red
Gray
Yellow/red
Yellow/green
Yellow/black
White/purple
82.2
Power/
12.8
Wiring table
(Scan center)
125.5
55
(Detecting window)
Protective
circuit
I/O
power
Center of
light-receiving
For USB
Note) Connect unused input cable to +COM (red).
Note) Connect unused output cable to -COM (gray).
ConnectorUSB
Binder 09-0431-81-04
USB
cable for UXM series (option)
UZ00023
19.6
M121
56
Cable 2m
55
