SHORTTERM

INTERNSHIP
(On-Site/Virtual)
 PROGRAM BOOK FOR

SHORT-TERM INTERNSHIP
(Onsite / Virt
PROGRAM BOOK FOR

SHORT-TERM INTERNSHIP
(Onsite / Virtual)

NAME OF THE STUDENT : SHAIK. SALMA

NAME OF THE COLLEGE : SIR C.R.REDDY COLLEGE FOR WOMEN

REGISTRATION NUMBER: 213307137444

PERIOD OF INTERNSHIP: From: 21/08/2023

To: 30/09/2023

NAME & ADRESS OF THE : SAMPATH INFO PVT LTD ,SAI NAGAR, CHODIMELLA
INTERN ORGANIZATION ELURU-534002.
 An Internship Report on
EMBEDDED SYSTEMS

(Title of the Internship)

Submitted in accordance with the requirement for the degree of

EMBEDDED SYSTEMS

Under the Faculty Guideship of

(Name of the Faculty Guide)

K.JYOTHSNA MADAM

Department of

ELECTRONICS

(Name of the College)

Submitted by:

SHAIK. SALMA

(Name of the Student)

Reg. No: 213307137444

Department of

ELECTRONICS

(Name of the College)

SIR C.R.REDDY COLLEGE FOR WOMEN

Page No:
 Instructions to Students

Please read the detailed Guidelines on Internship hosted on the website of AP State Council of
Higher Education https://apsche.ap.gov.in

1. It is mandatory for all the students to complete 2 months (180 hours) of short- term internship
either physically or virtually.
2. Every student should identify the organization for internship in consultation with the College
Principal/the authorized person nominated by the Principal.
3. Report to the intern organization as per the schedule given by the College. You must make your
own arrangements of transportation to reach the organization.
4. You should maintain punctuality in attending the internship. Daily attendance is compulsory.
5. You are expected to learn about the organization, policies, procedures, and processes by
interacting with the persons working in the organization and by consulting the supervisor
attached to the interns.
6. While you are attending the internship, follow the rules and regulations of the intern
organization.
7. While in the intern organization, always wear your College Identity Card.
8. If your College has a prescribed dress as uniform, wear the uniform daily, as you attend to
your assigned duties.
9. You will be assigned with a Faculty Guide from your College. He/She will be creating a
WhatsApp group with your fellow interns. Post your daily activity done and/or any difficulty
you encounter during the internship.
10. Identify five or more learning objectives in consultation with your Faculty Guide. These
learning objectives can address:
● Data and Information you are expected to collect about the organization and/or industry.
● Job Skills you are expected to acquire.
● Development of professional competencies that lead to future career success.
11. Practice professional communication skills with team members, co-interns and your supervisor.
This includes expressing thoughts and ideas effectively through oral, written, and non-verbal
communication, and utilizing listening skills.
12. Be aware of the communication culture in your work environment. Follow up and communicate
regularly with your supervisor to provide updates on your progress with work assignments.
13. Never be hesitant to ask questions to make sure you fully understand what you need to do your
work and to contribute to the organization.
14. Be regular in filling up your Program Book. It shall be filled up in your own
handwriting. Add additional sheets wherever necessary.
15. At the end of internship you shall be evaluated by your Supervisor of the intern organization.
16. There shall also be evaluation at the end of the internship by the Faculty Guide and the
Principal.
17. Do not meddle with the instruments/equipment you work with.
18. Ensure that you do not cause any disturbance to the regular activities of the intern organization.
19. Be cordial but not too intimate with the employees of the intern organization and your fellow
interns.
20. You should understand that during the internship programme, you are the ambassador of your
College, and your behavior during the internship programme is of utmost importance.
21. If you are involved in any discipline related issues, you will be withdrawn from the internship
programme immediately and disciplinary action shall be initiated.
22. Do not forget to keep up your family pride and prestige of your College
 Student’s Declaration

I Sk. Salma, a student of short term internship Program, Reg.No.

213307137444 of the Department of Electronics of SIR C.R.REDDY College
does hereby declare that I have completed the mandatory internship from: 21-
08-2023 to: 30-09-2023 in SAMPATH INFO PVT LTD (Name of the intern
organization) under the Faculty Guideship of Y.Sri Devi madam (Name of
the Faculty Guide), Department of Electronics, SIR C.R.REDDY
COLLEGE FOR WOMEN (Name of the College)

(Signature and Date)

Endorsements

Faculty Guide

Head of the Department

Principal

Page No:
 Official Certification
This is to certify that SHAIK .SALMA(Name of the
student) Reg. No .213307137444 has completed
his/her Internship in SAMPATH INFO PVT LTD ( Name of
the Intern Organization) on EMBEDDED SYSTEM (Title
of the Internship) under my supervision as a part of
partial fulfillment of the requirement for the
Degree of EMBEDDED
SIR.C.R.REDDY COLLEGE (Name of the College).

This is accepted for evaluation.

(SIGNATORY WITH DATE AND SEAL)

ENDORSEMENTS:

FACULTY GUIDE :

HEAD OF THE DEPARTMENT:

PRINCIPLE:
in the Department of

Page No:
 Certificate from Intern Organization

This is to certify that of Sk. Salma, (Name of the intern) Reg. No: 213307137444 of SIR
C.R.REDDY COLLEGE FOR WOMEN (Name of the College) underwent internship in
SAMPATH INFO PVT LTD (Name of the Intern Organization) from: 21-08-2023 to: 30-09-
2023.

The overall performance of the intern during his/her internship is found to be

………………. (Satisfactory/Not Satisfactory).

Authorized Signatory with Date and Seal

Page No:
 ACKNOWLEDGEMENTS

It is inevitable that thoughts and ideas of other people drift into the subconsciousness
when one feels to give acknowledgement for the help given by others.
I’m very much grateful to Smt. P. Sailaja principal SIR C.R. REDDY COLLEGE
FOR WOMEN their blessings and encouragement through my course of internship.
I express my gratitude to Smt. S. Anuradha madam vice principal SIR C. R.
REDDY COLLEGE FOR WOMEN for her blessing and encouragement throughout
my course of internship.
It is my pleasure to express my sincere gratitude and thanks to
Mrs. Y. SRI DEVI madam head of the department of management studies and all
the other features of department of management studies for their encouragement and
continuous support.
We would like to express our gratitude towards our internship guide Mrs. K. Jyothsna madam
lecture in electronics for supporting us till the end of our project

I extend my sincere thanks to Ms. Sri devi internship in charge for internet of
things IOT for her support and valuable advice during my course of internship Ms. Y. Sridevi
mam and Ms. Jyoshna mam.

It is my immense pleasure to express my gratitude and thanks to Mrs. K.

Jyothsna mam and internship in charge of their guidance and support.

I would like to express my special gratitude Mr. D. Anil Kumar the director
Ms. Deepti kiranmayi, technical trainer for IOT from the company of Sampath info private
limited Eluru for Their internship guidance helps throughout the period of internship. It is my
duty to convey sincere thanks and regards to my parents, family members, friends and people
who have supported me throughout the course internship. Behind every achievement lies on
unfathomable sea of gratitude to those who activate it without whom if could ever have been in
existence to them we lay the words of gratitude imprinted with us.

I perceive this opportunity as a big mite store in my career

development. I will strive to use gained skills and knowledge the best
possible way.

Page No:
 Contents
CHAPTER NO: CONTENT: PGNO:
CHAPTER 1: 1.1 learning objectives
1.2 learning outcome
1.3 about internship organization
1.4 summary
CHAPTER 2: Overview of the organization
CHAPTER 3: Internship part
CHAPTER 4: Week 1: introduction, blinking and fading LED
Week 2: experiments on fetch the microcontroller response,
simulating smart Street lights and temperature
measuring using LM35.
Week 3: experiments on multiple blinking,
IR sensor, introduction raspberry pi.
Week 4: LED blinking IR sensor using raspberry pi.
Week 5: experiments on program a button
using LED, RADAR, water level
Indicator, fire alarm using raspberry pi & Arduino.
Week 6: revising on experiments.
CHAPTER 5: Outcome description
5.1 work environment
5.2 real time technical skills
5.3 managerial skills
5.4 communication skills
5.5 technological development.
CHAPTER 6: Student self-evaluation of the long internship.
CHAPTER 7: photos and video links
CHAPTER 8: evaluation
8.1 internal assessment statement
8.2 external assessment statement

Page No:
 CHAPTER 1: EXECUTIVE SUMMARY

The internship report shall have only a one-page executive summary. It shall include five or more
Learning Objectives and Outcomes achieved, a brief description of the sector of business and intern
organization and summary of all the activities done by the intern during the period.

Understanding the basic concept of computation thinking and programming

• Be familiar with Arduino hardware and interface know that Arduino
•Identity the reason why Arduino is commonly used
•Identity and understand the hardware needed in creating Arduino
Learning Objective:
•Get an idea of what IOT is
• Get an overview of the course
•Learn the very basic of python
•Learn the basics of python
Be able to write simple python programs to control a Rip’s be able to document and present
you work corporate professionalism [Treating tour Managers, colleagues and client with
respect, projecting a positive attitude being polite, showing good judgment, being official]
Communication and interpersonal skills in social work [ How to communication effectively and
good internship inter personality]
Outcomes achieved:
• Acquired knowledge on IOT, python and raspberry pi
•learned about sensor in IOT
•Learned about introduction to Arduino raspberry pi
• IOT hands on experience
•Completion of project with enhance pre final technical and communication
Summary of all activities
• Interns completed their project IOT based on sensor of Arduino and raspberry
pi
• Become familiar with the Automatic control system hardware components
• Setup the AEV software on the Arduino IDE
•Becoming familiar with uploading programs to the Arduino testing the programs
and troubleshooting techniques
• Learned the best and advantages of IOT, Arduino, raspberry pi

Page No:
 CHAPTER 2: OVERVIEW OF THE ORGANIZATION
Suggestive contents
A. Introduction of the Organization
B. Vision, Mission and Values of the Organization
C. Policy of the Organization, in relation with the intern role
D. Organizational Structure
E. Roles and responsibilities of the employees in which the intern is placed.
F. Performance of the Organization in terms of turnover, profits, market reach and market value.
G. Future Plans of the Organization.

A. Introduction of the organization: Established in 2017 “SAMPATH INFO

PVT LTD'' is the pioneer and premier division on advanced technologies like
big Data analytics, Data science, AWS, IOT, Robotics and salesforce in Eluru,
we have prominent name in the fields of offline and online training a web
solutions SAMPATH INFO PVT LTD has been associated with a number of
engineering and degree colleges for job-oriented training and student career
programs. We have a team with well experienced and certified Trainer’s
developers and programmers who evaluated the potential and interest of the
student and accordingly customized the servicer.

B. Vision, Mission, and values of the organization:

Our vision: To become the qualitative learning ecosystem for computer

literacy, in partnership with academic and corporate clients.
Our Mission: To create a learning platform for students & working
professionals who wish to pursue technical training by attending instructor-
LED online/classroom courses, using a team of industry XY trainers we aim
to up-skill and participate with the advanced skills to their professional life to
the form beginners to accept level.
Future plans: We are striving to be best and ongoing according to the
technology trends our future plans are to move into development.
With structure where we can provide opportunities to people along with
world class computer literacy

Page No:
 C. Policy:

We at Sampath info Pvt limite d want to make your learning

Experience satisfying. We respect your privacy by delivering the best

content to learners.

D. Organizational structure:

E. Roles and Responsibilities of the employee in which the intern is placed:

Ø Giving practical experience and techno functional knowledge on
intern projects.
Ø Completing the assigned projects of intern

Page No:
 CHAPTER 3: INTERNSHIP PART

Description of the Activities/Responsibilities in the Intern Organization during Internship, which shall
include - details of working conditions, weekly work schedule, equipment used, and tasks performed.
This part could end by reflecting on what kind of skills the intern acquired.

working conditions:

Intern having classroom training Internet of things technology.

Interns also having the daily 2-3 hours hands on experience in

the lab sessions regarding their project weekly work schedule

week-1: Introduction, Blinking and Fading of a led smart street lights and temperature measurement
using Im35

week-2: Experiments on fetch the micro controller response, simulating

week-3: Experiments on multiple blinking. IR sensor, Introduction to Raspberry pi.

week-4: Led blinking, IR sensor using raspberry pi

week-5: Experiments on programming a button using led. RADAR, water level indicator, fire alarm
using raspberry pi & Arduino

System Requirements:

1) System: Pc/laptop

2) Operating system: windows 10/11 or Linux

3) Internet connection

Task performed:

1) Interns completed their project Internet of thing IOT

2) Learned the best and advantages of Internet of things 3) Successfully deployed projects in IOT.

Page No:
 ACTIVITY LOG FOR THE FIRST WEEK

DA LEARNING OUTCOME Person

Y BRIEF DESCRIPTION OF THE DAILY
In-charge
& ACTIVITY
Signature
DAT
E
Introduction to IOT History of IOT,how IOT works Identify the components that
applications of IOT. form part of IOT
architecture.
Day
–
1

Introduction to microcontroller, Arduino Mega Determine the most

2560,Raspberry pi.Arduino installation. appropriate
Introduction Arduino software. IOT devices and sensors
Day based on case studies.
-
2
Include basic explanation of set up the connection
Arduino.Introduction Arduino software. between the devices and
Day sensor.
–
3

Different sensors introduce LDR, LM35,IR Evaluate the appropriate

Receiver ,ultrasonic sensor,flame sensor, PIR protocol for communication
Day motions sensor ,laser module buzzer . between IOT.
–
4

Working principle of software started working Working on blinking on

on first experiment BLINKING AN LED ON LEDs. the HELLO world of
Day ARDUINO MEGA,explanation of code .Use microcontrollers.
– for experiment.
5

Learn about the use of analog output through Finally,experiments are

digital pin with experiment. FADING AN LED working and it can succeed
Day ARDUINO MEGA.Explanation of code used in IOT devices.
– for experiment.
6

Page No:
 WEEKLY REPORT
WEEK – 1 (From Dt………..….. to Dt… )
Objective of the Activity Done:

Detailed Report:

As an IOT Intern during my first week , I have learned about IOT, working,applications of IOT.

Introduction to Microcontroller Arduino Mega 2560,Raspberry pi,various:IOT development tools

Arduino
installation from Arduino website,introduction to Arduino software basic explanation of Arduino code

different sensor introduction like(LDR,LM35,IR receiver,Ultrasonic sensor,Flame sensor,PIR motion

sensor,laser module buzzer).I have understood the use and importance of IOT.Latest analog output can
be
retrieved from digital pin through PWM in fading experiment. Learn functionality of Arduino through

basic blinking experiment.

Working principle of Blinking and Fading a LED:

Demonstrate the use of analog output of fade an LED.This example demonstrate the use of the
analog
Write () function in fading an LED off and on.AnalogWrite uses pulse width modulation(PWM),turning
a
digital pin on and off very quickly with different ratios between on and off,to create a fading effect.

Applications of LED:

● Warehouse

● Factories

● Offices

● Parking slots

● Garages

● Health care facilities

Page No:
 ACTIVITY LOG FOR THE SECOND WEEK

DA LEARNING OUTCOME Person

Y BRIEF DESCRIPTION OF THE DAILY
In-charge
& ACTIVITY
Signature
DAT
E
Introduction to Microcontroller and I have learnt an introduction
Applications. to Microcontroller and
Applications .
Day
–
1

Explanation & practical session on fetch the I have learned & hands on
microcontroller response and output control on experience on explanation on
serial monitor 1 or 2. fetch the microcontroller
Day response and output control
- on serial monitor 1 or 2.

2
Introduction to LED and LDR ,working I have learned Introduction
principle of LDR and LED , and its to LED and LDR ,working
Day Applications. principle of LDR and LED ,
– and its Applications.
3

Explanation & practical explanation on Determined the explanation

simulating smart lights using LDR,LED with on simulating smart lights
Day Arduino. using LDR,LED with
– Arduino.
4

Introduction to LM35 and theory explanation I have learned an

on the experiment measuring room temperature introduction to LM35 uses or
Day using LM35. few applications in real time
– scenarios of experiment.
5

Page No:
 Practical explanation on the experiment Hands-on experience on an
measuring room temperature using LM35. experiment measuring room
Day temperature using LM35.
–
6

Page No:
 WEEKLY REPORT
WEEK – 2 (From Dt………..….. to Dt… )

Objective of the Activity Done:

Detailed Report:

As an IOT intern during my second week, I have learned about the introduction to Microcontroller ,their

working & applications.Practiced on experiment, fetching microcontroller response and output control
on
serial monitor by giving input 1 or 2.Learn the functions used in code . Successfully performed
simulating
the smart street light using LDR and LED . It is amazing to know the working principle of LDR used in

smart street lights. Got to know the explanation of code used in this experiment and LDR application

happy to working on real-time experiments .The LDR is used for automatic contrast and brightness

control in television receivers.

I have learnt about introduction to LM35, uses or few application in real-time scenario
of
experiment.Basic principle of a diode to measure known temperature value and pin diagram
explanation.
Practical explanation on the experiment measuring room temperature using LM35.

LM35 provides output voltage in centigrade (celsius).It does not require any external calibration
circuitry.
The LM35 device is rated to operate over a -55 degree celsius to 150 degree celsius temperature range ,

while the LM35 device is rated for a -40 degree celsius to 110 degree celsius range.

Page No:
 ACTIVITY LOG FOR THE THIRD WEEK

DA LEARNING OUTCOME Person

Y BRIEF DESCRIPTION OF THE DAILY
In-charge
& ACTIVITY
Signature
DAT
E
Learnt how it generates a continuous output in I have learned how to
the form of square wave at pin in multiple generate continuous output in
blinking of LED. the form of a square wave at
Day the pin in multiple blinking
– of LEDs.
1

Practical explanation on experiment multiple I have learned how to

blinking of LED on the Arduino. generate continuous output in
the form of a square wave at
Day the pin in multiple blinking
- of LEDs.

2
Introduction to IR sensor and explanation of IR I have learned Introduction
sensor pins and theory session on experiment to IR sensors and explanation
Day implementing on obstacle sensor using IR of IR sensor pins and how to
– sensor . implement the experiment .
3

Practical session on experiment upload code Hands-on experience on

using (VNC Viewer) Arduino. experiment upload code
Day using (VNC Viewer)
– Arduino.
4

Notes on above all experiments and some Finally experiments are done
applications. .
Day
–
5

Introduction to Raspberry pi ,working principle I have learned about

of Raspberry pi and applications . Introduction to Raspberry
Day pi ,working principle of
– Raspberry pi and
applications .
6

Page No:
 WEEKLY REPORT
WEEK – 3 (From Dt………..….. to Dt… )
Objective of the Activity Done:

Detailed Report:

As an IOT intern during my third week,I have learned how to generate continuous output in the form
of a
square wave at pin in multiple blinking of LED,practical explanation on experiment multiple blinking of

LED on the Arduino.finally multiple blinking of LED.

And learned about the introduction to IR sensor,and explanation of various IR pins.Working

principle of IR sensor and its applications.Advantages and uses in real-time scenario experiment. got
some
knowledge on obstacle sensor.learned how to upload the code with notes of sensor and practical .

Learned about introduction to Raspberry pi ,Working principle os Raspberry pi and its applications

Learned about the explanation of Raspberry pi pin diagram,LED blinking using Raspberry
pi.Also
I learned an introduction to VNC viewer and the steps involved and uploaded the code. I got the
practical
experience on using Raspberry pi .Finally we are done with Raspberry pi and some of its applications.

Raspberry pi is a small and affordable computer board that can be used for many applications.
some of
its applications are:

● Media streamer

● Tablet computer

● Home Automation

● Internet Radio

● Controlling robots

● Computer

Page No:
 ACTIVITY LOG FOR THE FOURTH WEEK

DA LEARNING OUTCOME Person

Y BRIEF DESCRIPTION OF THE DAILY
In-charge
& ACTIVITY
Signature
DAT
E
Explanation of Raspberry pi, pn diagram and I have learned about
introduction of VNC Viewer and learn steps to introduction to raspberry pi ,
upload code . working principle and VNC
Day Viewer and various steps to
– upload.
1

Explanation on LED blinking using Raspberry Learned about how an LED

pi.Practical explanation of LED blinking using blinking using Raspberry
Raspberry pi. pi.Hands on experience on
Day experiments on LED
- blinking using raspberry pi.

2
Review on basic Arduino experiments and Review on basic Arduino
viva. experiment and viva.
Day
–
3

Introduction to Ultrasonic sensor working I have learned the working

principle .Theory session on water level principle of ultrasonic
Day indicator using Raspberry pi and Raspberry pi sensors . Implementing an
– ana\d Ultrasonic sensor. experimental water level
indicator using Raspberry pi
4
and ultrasonic sensor.

Practical session on experiments with water I have learned about how to

level indicator using Raspberry pi and use a water level indicator
Day ultrasonic sensor. using Raspberry pi and
– Ultrasonic sensor.
5

Practical session on experiments upload code Hands-on experience on

using Raspberry pi,started documentation. experiment upload code
Day using Raspberry pi.
–
6

Page No:
 WEEKLY REPORT
WEEK – 4 (From Dt………..….. to Dt……………………………. )
Objective of the Activity Done:

Detailed Report:

As an IOT intern during my fourth week,I have learned about introduction to Raspberry pi ,working

principle of Raspberry pi and VNC Viewer and various steps to upload the code .

Learned about how an LED blinking using Raspberry pi .Hands on experience on experiments

on LED blinking using raspberry pi. Review on basic Arduino experiment and viva.

I have learned the working principle of ultrasonic sensors . Implementing experiment water

level indicator using Raspberry pi and ultrasonic sensor.

I have learned about how to use a water level indicator using Raspberry pi and Ultrasonic

sensors. Hands-on experience on experiment upload code using Raspberry pi.

Applications of Raspberry pi:

● Raspberry pi as desktop

● Home Automation

● Media usage

● Games server

● Retro gaming machines

Applications of UltraSonic sensor :

● Parking assist systems

● Distance -measuring devices

● Welding of plastics and metals,localizing

Page No:
 ACTIVITY LOG FOR THE FIFTH WEEK

DA LEARNING OUTCOME Person

Y BRIEF DESCRIPTION OF THE
In-charge
& DAILY ACTIVITY
Signature
DAT
E
Theory session and practical session on I learned to implement the
programming a button using Arduino. experiment and handson by
doing experiments.
Day
–
1

Theory sessions and practical sessions on Headson by the done this

experiment ultrasonic ranging using Arduino experiment and introduction of
and processing rader. ultrasonic sensor and pins.
Day
-
2
Theory sessions and practical sessions on I learned how to implement the
water level indicator using raspberry pi and experiment.
Day ultrasonic and flame sensor.
–
3

Theory sessions and practical sessions on fire I learned how to implement

alarm using Arduino and flame sensor. the experiment and handson by
Day doing experiments.
–
4

Continued designing ppt and Determine the taking

document.Taking screenshots of input and screenshots of input and
Day output screen or circuit connections. output screen or circuit
– connections.
5

Page No:
 Preparations for viva and handson PPT and viva are done
projects,ppt presentation and viva.
Day
–
6

Page No:
 WEEKLY REPORT
WEEK – 5 (From Dt………..….. to Dt… )
Objective of the Activity Done:

Detailed Report:

As an IOT intern during my fifth week,I learned to implement the experiment and handson by

doing experiments. Headson by the done this experiment and introduction of ultrasonic sensor and pins .

I learned how to implement the experiment.

I learned how to implement the experiment and handson by doing experiments.

Determine the taking screenshots of input and output screen or circuit connections.

PPT and viva are done.

A mock presentation of the project is given and some suggestions were given to improve our

preparation ,practice for viva is done .Documentation is done ,setting font and size of headings ,font and

size of matter .Viva preparation is done.Finally ,the project is completed.

Page No:
 CHAPTER 5: OUTCOMES DESCRIPTION

Describe the work environment you have experienced (in terms of people interactions, facilities
available and maintenance, clarity of job roles, protocols, procedures, processes, discipline, time
management, harmonious relationships, socialization, mutual support and teamwork, motivation, space
and ventilation, etc.)
A work environment is a place where a person or intent or people performs job.it can impact the
feeling ,
relationship and growth of interns during the internship. I did my internship on able to experience a
good
environment.I interacted with SAMPATH INFO PRIVATE LIMITED .Mr .D. ANIL KUMAR who

offered me the opportunity of an internship.

I interacted my project guides Mrs.DEEPTHI KIRANMAYI,

who trained us and give some valuable suggestions and rendered her incompletion of my project.our

internal guides Mrs.Y. SRIDEVI guided us .the co interns and faculty were friendly and approachable

so it was easy for me to help and clarify things whenever I needed it .

The facilities were in workplace were maintained well .a lab with

fully equipped computer systems wifi and projector to take classes.the work had well established
protocols
,procedure and processes that were strictly.the timing are with minimal breaks for mind .clear guidance

was given regarding the different activities to be done.

The internship time was full of discipline and made me punctual in completing my

work in time and develop my time management skills . I experienced some harmonious relationships

with my co interns and guides ,lecturers to work together and complete the internship.

During this i realized that was a mutual support between all of even in the bunch over works
my
teammates supported and help me to get out of p;ressure of over work.Raising my network of people

to enhance my community and interpersonal skills .

The work was adequate and ventilation was good .My experience in the work .

my experience in the work environment during my internship was positive with help

me to stay motivated and my internship successful.

Page No:
 Describe the real time technical skills you have acquired :

(in terms of the job- related skills and hands on experience)

PYTHON IN IOT:

Internet on things system had design and developed swiftly and

competently whenever this occurs , to activity is instantly come to life one is to program the IOT devices
and organized a backend to interact with this devices Python becomes a great choice we can use either
on backend side are software device moreover Python available to work on Linux device and we can
make use of micropython for microcontrollers.

The volume of data that we need to deal with accessible in the

cloud Python recognises that need regardless of whether we create IOT projects from scratch or
interact with activators,sensors and accessories in both activities we can utilize the python language for
the development device with small computing resources and accordingly at very low price.

ARDUINO IN IOT:

One of the most important task when making an iot device using arduino is to
connect in simple words that what is a network of physically that connected to the network the think can
be call the internet of things device are received data to do and from the internet IOT devices can also
exchange data with each other via the internet.

Arduino collect sensors data and send the database

arduino collect the sensors data and send to IOT cloud are do not detect the event and send notification via
Email smartphones cause and push button small speakers like Amazon echo dot google home arduino interact
automatically with other devices using protocols such top.arduino works as a gateway which is a bridge
between other devices and the internet.

Page No:
Describe the managerial skills you have acquired (in terms of planning, leadership, team work,
behavior, workmanship, productive use of time, weekly improvement in competencies, goal setting,
decision making, performance analysis, etc.

LEADERSHIP:

leadership is a strategic vision and ability to communicate potential of what we have learn that
leadership has a data analysis it development and security we also learn that a leadership must know
that it has a customer orientation

DECISION MAKING:

We have learnt from my respective lectures and trainers that making a good decision includes
involvement in the experiments and understanding the needs of connection and the folding part and we
discuss with our teammates which ensures coordination between us.

SETTING A GOAL:

we also learn some key consideration and setting a goal and we followed some keys like that the goal
must be achievable,realistic and can be measurable mainly goal must be time based

PERFORMANCE ANALYSIS:

Our respective lecturer observed our performance and helped us to improve our skills more effectively
and efficiently.

WORKMANSHIP:

observed our work and explained some simple ways to do work in a most fluent way.

PLANNING SKILLS :

I have learned to plan my work each day and what I need for the next day without postponing. planning
skill in iot a is crucial in real time.

BEHAVIOR:

I have learned so many things from my lecturers and trainers that behavior is very important while
doing experiments . I maintain good behavior while listening.

PRODUCTIVE USE OF TIME :

Time is very valuable and we utilize our time while performing experiments and also learned the
experiments Effectively.

Page No:
 Describe how you could improve your communication skills

(in terms of improvement in oral communication, written communication, conversational abilities,

confidence levels while communicating, anxiety management, understanding others, getting understood by
others, extempore speech, ability to articulate the key points, closing the conversation, maintaining niceties
and protocols, greeting, thanking and appreciating others, etc.,)

Communication is not only about what you say but also how you say if I always communicate with my
team is a very polite way and also I give respect to my team in all aspects such as listening Idea and
thoughts.

I always listen to my co - interns to understand exactly what they are telling and in turn I can give any
suggestions and modifications for what they said. Through this I can build a good relationship with my
team .

communicating face to face with my our co- interns is always the best opinion I always used to
communicate with my co interns face to face so that I can develop trust and workplace relationship
more quickly

In my internship program ,I learn how to communicate with different people with different
mind set I have learn to be confident while expressing my ideas and thoughts to my co-intern so that I
can communicate with them in a better way

I always thank my team members who help me to get the knowledge about
the project that we are done I always make sure that my ideas and thoughts to be detected clearly not to
repeat same thing again and again which leads to over communication

Page No:
 Describe how you could enhance your abilities in group discussions, participation in teams,
contribution as a team member, leading a team/activity.

I enhance my abilities in a group discussion by introducing the topic and purpose of the discussion
introducing myself and the other team members making sure all the members have approximately the
same time to speak thanking group members for their contribution and being objective in summarizing
the group discussion and achievement

I always participate in any group discussion with my co interns with an appropriate tone that means I
can be I convey my thoughts and ideas in your very soft and polite manner and also I speak to m y team
with the high confidence in sharing my valuable thoughts

The three things I contribute to my team member is

being prepared attentive and original.i always be prepared in contributing my ideas and thoughts to my
team in a meaningful way I always be active and listening my team members ideas I used to be myself in
any of the group discussion with my teammate

For most of the group discussions the members

who lead the team have a major role in establishing a comfortable atmosphere and make a set of rules in
any discussion so I have managed my team with the set of rules and such as no arguments people but
only at ideas and opinion

The disagreement should be respectful but not ridiculous don't interrupt listen
to the other team members thoughts expect the other times try to keep your comments reason will short
and to be point so that the others have a chance to respond consider seriously and try to evaluate them
fairly don't be defensive if someone disagree with you everyone is responsible for following and holding
the ground rule.

Page No:
 Describe the technological developments you have observed and relevant to the subject area of
training (focus on digital technologies relevant to your job role)

TECHNICAL SKILLS USED IN IOT:

MICRO CONTROLLER:

A Microcontroller is a compact Integrated circuit design to govern a specific operation

in an embedded system a typical microcontroller includes a processor memory and input or output devices or
peripherals on a single chip sometimes referred to as an embedded controller or microcontroller unit in MCU
microcontrollers are found in vehicles ,robots ,office machines etc.

ARDUINO UNO:

The ARDUINO UNO is an open source microcontroller both based on the microchip 80
Mega 3208 P microcontroller MCU and developed my arduino CC and initially released in 2010 the board has 14
digital input output pins . 6 capable of PWM output 6 analogue input and output pins and is programmable with
the ARDUINO IDE via a type 13 USB.

RASPBERRY PI:

The Raspberry Pi is a low cost credit card sized computer that plugs into a computer monitor or TV that uses its
standard keyboard and mouse. It is capable of a few devices that enable people of all ages to explore computing
and to learn how to program in languages like scratch and python.

LM35:

LM 35 is a commonly known used temperature sensor; it shows values in the form of output voltage instead of
degree Celsius; it can be also used for measuring battery temperature.

IR SENSOR:

IR sensor is an electronic device that emits light in order to send some objects to the surrounding area.

ULTRASONIC SENSORS:

An ultrasonic sensor is an electrical device that measures the distance of a target object by emitting ultrasonic
sound waves and converting the reflected sound into an electrical signal; it has two main components: transmitter
and receiver.

LDR:

Photoresistor are also known as light dependent resistors, are light sensitive devices most often used to indicate
the presence and absence of light are two measures of the light intensity.

LED LIGHT:

LED stands for light emitting diode LED lighting products that produce light up to 90% more efficiently than
incandescent light bulbs.

Page No:
 Student Self Evaluation of the Short-Term Internship

Student Name:& Register no: Sk. Salma, (213307137444)

Term of Internship:From: 21-08-2023 To: 30-09-2023

Date of Evaluation:

Organization Name & Address: SAMPATH INFO PVT LTD, Sai Nagar, chodimella, Eluru-534002

Name & Address of the Supervisor

with mobile NO:

Please rate your performance in the following areas:

Rating Scale: Letter grade of CGPA calculation to be provided

1) Oral communication 1 2 3 4 5

2) Written communication 1 2 3 4 5

3) Initiative 1 2 3 4 5

4) Interaction with staff 1 2 3 4 5

5) Attitude 1 2 3 4 5

6) Dependability 1 2 3 4 5

7) Ability to learn 1 2 3 4 5

8) Planning and organization 1 2 3 4 5

9) Professionalism 1 2 3 4 5

10) Creativity 1 2 3 4 5

11) Quality of work 1 2 3 4 5

12) Productivity 1 2 3 4 5

13) Progress of learning 1 2 3 4 5

14) Adaptability to organization’s culture/policies 1 2 3 4 5

15) OVERALL PERFORMANCE 1 2 3 4 5

Signature of the Student

Page No:
 Evaluation by the Supervisor of the Intern Organisation

Student Name:& Register no:Sk. Salma, (213307137444)

Term of Internship:From: 21-08-2023 To: 30-09-2023

Date of Evaluation:

Organization Name & Address: SAMPATH INFO PVT LTD, Sai Nagar, chodimella, Eluru-534002

Name & Address of the Supervisor

with mobile NO:

Please rate the student’s performance in the following areas:

Please note that your evaluation shall be done independent of the Student’s self-

evaluation Rating Scale: 1 is lowest and 5 is highest rank

1) Oral communication 1 2 3 4 5

2) Written communication 1 2 3 4 5

3) Initiative 1 2 3 4 5

4) Interaction with staff 1 2 3 4 5

5) Attitude 1 2 3 4 5

6) Dependability 1 2 3 4 5

7) Ability to learn 1 2 3 4 5

8) Planning and organization 1 2 3 4 5

9) Professionalism 1 2 3 4 5

10) Creativity 1 2 3 4 5

11) Quality of work 1 2 3 4 5

12) Productivity 1 2 3 4 5

13) Progress of learning 1 2 3 4 5

14) Adaptability to organization’s culture/policies 1 2 3 4 5

15) OVERALL PERFORMANCE 1 2 3 4 5

Signature of the Supervisor

Page No:
PHOTOS & VIDEO LINKS

Page No: