2W10MG 2W10MG.
Bridge Rectifier
Features:
• Glass passivated.
• Surge overload rating -60 amperes peak.
• Ideal for printed circuit board.
• Reliable low cost construction utilizing moulded plastic technique
results in expensive product.
• Mounting position : Any.
• Lead : Sliver plated copper lead.
Reverse Voltage - 1,000 V
Forward Current - 2 Amperes
WOBM
Dimensions : Inches (Millimetres)
www.element14.com
www.farnell.com
www.newark.com
Page <1> 06/07/11 V1.1
Bridge Rectifier
Maximum Ratings and Electrical Characteristics
Rating at 25°C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Characteristics Symbol 2W10MG Unit
Maximum Recurrent Peak Reverse Voltage VRRM 1,000
Maximum RMS Bridge Input Voltage VRMS 700 V
Maximum DC Blocking Voltage VDC 1,000
Maximum Average Forward
I (AV) 2
Rectified Current at TA = 25°C
A
Peak Forward Surge Current, 8.3 ms Single
IFSM 60
Half Sine-wave Super Imposed on Rated Load
I2t Rating for Fusing (t < 8.3 ms) I2t 15 A2s
Maximum Forward Voltage Drop Per Element at 2 A Peak VF 1.1 V
Maximum Reverse Current at Rated TJ = 25°C 10 µA
IR
DC Blocking Voltage TJ = 100°C 1 mA
Typical Junction Capacitance Per Element (Note 1) CJ 30 pF
Operating Temperature Range TJ
-55 to +150 °C
Storage Temperature Range TSTG
Note : 1. Measured at 1 MHz and applied reverse Voltage of 4 V dc.
Rating and Characteristics Curves
Maximum Non-Repetitive Peak Forward
Forting Curve Output Rectified Current Surge Current
Peak Forward Surge Current,
Average Forward Output
Current Amperes
Amperes
Ambient Temperature (°C) Number of Cycles at 60 Hz
www.element14.com
www.farnell.com
www.newark.com
Page <2> 06/07/11 V1.1
Bridge Rectifier
Rating and Characteristics Curves
Typical Reverse Characteristics Typical Forward Characteristics
Instantaneous Forward Current Amperes
Instantaneous Reverse Current,
Microamperes
Percent of Rated Peak Reverse Voltage Instantaneous Forward Voltage, Volts
Typical Junction Capacitance Per Bridge Element
Capacitance, (pF)
Reverse Voltage, Volts
Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No licence is granted for the use of
it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces
all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use
made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted.
Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising)
is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2011.
www.element14.com
www.farnell.com
www.newark.com
Page <3> 06/07/11 V1.1
2W10MG 2W10MG.
Powered by TCPDF (www.tcpdf.org)
