Machine Serial No.

: -#4560, #4880-#4922 SPECIFICATIONS

1. MAJOR COMPONENT

Tool box Fuel tank Hydraulic tank Main pump

Engine

Charge air cooler

Radiator
Tooth Bucket Turning joint Swing motor Main control valve Oil cooler

Arm Arm cylinder Boom Boom cylinder Cab Precleaner Counterweight

Swing
bearing

Bucket cylinder Connecting link Idler Carrier roller Sprocket

Side cutter Connecting rod Track roller Track Travel motor

210S2SP01A

2-1
Machine Serial No. : -#4560, #4880-#4922
2. SPECIFICATIONS

1) HX210S, MONO BOOM

I(I') D
C

E
G
F

H
J M
K N
A B(L)
210S2SP02A

Unit Specification
Boom 5.68 (18' 8")
Description m (ft-in)
Arm 2.92 (9' 7") 2.00 (6' 7") 2.40 (7' 10")
mm (in) Shoe 600 (24)
Operating weight kg (lb) 20830 (45920) 20670 (45570) 20740 (45720)
Bucket capacity (SAE heaped), standard m³ (yd³) 0.92 (1.20) 0.92 (1.20) 0.92 (1.20)
Overall length A 9530 ( 31' 3") 9650 ( 31' 8") 9570 ( 31' 5")
Overall width B 2800 ( 9' 2") 2800 ( 9' 2") 2800 ( 9' 2")
Overall height of boom C 3030 ( 9' 11") 3200 ( 10' 6") 3110 ( 10' 2")
Superstructure width D 2700 ( 8' 10") 2700 ( 8' 10") 2700 ( 8' 10")
Overall height of cab E 3000 ( 9' 10") 3000 ( 9' 10") 3000 ( 9' 10")
Ground clearance of counterweight F 1060 ( 3' 6") 1060 ( 3' 6") 1060 ( 3' 6")
Overall height of engine hood G 2380 ( 7' 10") 2380 ( 7' 10") 2380 ( 7' 10")
Overall height of handrail G' 2970 ( 9' 9") 2970 ( 9' 9") 2970 ( 9' 9")
mm (ft-in)
Minimum ground clearance H 470 ( 1' 7") 470 ( 1' 7") 470 ( 1' 7")
Rear-end distance I 2770 ( 9' 1") 2770 ( 9' 1") 2770 ( 9' 1")
Rear-end swing radius I' 2845 ( 9' 4") 2845 ( 9' 4" ) 2845 ( 9' 4")
Distance between tumblers J 3360 ( 11' 0") 3360 ( 11' 0") 3360 ( 11' 0")
Undercarriage length K 4170 ( 13' 8") 4170 ( 13' 8") 4170 ( 13' 8")
Undercarriage width L 2800 ( 9' 2") 2800 ( 9' 2") 2800 ( 9' 2")
Track gauge M 2200 ( 7' 3") 2200 ( 7' 3") 2200 ( 7' 3")
Track shoe width, standard N 600 ( 2' 0") 600 ( 2' 0") 600 ( 2' 0")
Travel speed (low/high) km/hr (mph) 3.5/5.7 (2.2/3.5) 3.5/5.7 (2.2/3.5) 3.5/5.7 (2.2/3.5)
Swing speed rpm 12.2 12.2 12.2
Gradeability Degree (%) 35 (70) 35 (70) 35 (70)
Ground pressure kgf/cm² (psi) 0.48 (6.81) 0.48 (6.76) 0.48 (6.78)
Max traction force kg (lb) 21100 (46517) 21100 (46517) 21100 (46517)

2-2
Machine Serial No. : -#4560, #4880-#4922
2) HX220S, MONO BOOM

I(I') D
C

E
G
F

H
J M
K N
A B(L)
210S2SP03

Unit Specification
Boom 5.68 (20' 6")
Description m (ft-in)
Arm 2.92 (9' 7") 2.00 (6' 7") 2.40 (7' 10")
mm (in) Shoe 600 (24)
Operating weight kg (lb) 21260 (46870) 21100 (46520) 21160 (46650)
Bucket capacity (SAE heaped), standard m³ (yd³) 0.92 (1.20) 0.92 (1.20) 0.92 (1.20)
Overall length A 9530 ( 31' 3") 9650 ( 31' 8") 9570 ( 31' 5")
Overall width B 2990 ( 9' 10") 2990 ( 9' 10") 2990 ( 9' 10")
Overall height of boom C 3030 ( 9' 11") 3200 ( 10' 6") 3110 ( 10' 2")
Superstructure width D 2700 ( 8' 10") 2700 ( 8' 10") 2700 ( 8' 10")
Overall height of cab E 3000 ( 9' 10") 3000 ( 9' 10") 3000 ( 9' 10")
Ground clearance of counterweight F 1060 ( 3' 6") 1060 ( 3' 6") 1060 ( 3' 6")
Overall height of engine hood G 2380 ( 7' 10") 2380 ( 7' 10") 2380 ( 7' 10")
Overall height of handrail G' 2970 ( 9' 9") 2970 ( 9' 9") 2970 ( 9' 9")
mm (ft-in)
Minimum ground clearance H 470 ( 1' 7") 470 ( 1' 7") 470 ( 1' 7")
Rear-end distance I 2770 ( 9' 1") 2770 ( 9' 1") 2770 ( 9' 1")
Rear-end swing radius I' 2845 ( 9' 4") 2845 ( 9' 4") 2845 ( 9' 4")
Distance between tumblers J 3650 ( 12' 0") 3650 ( 12' 0") 3650 ( 12' 0")
Undercarriage length K 4440 ( 14' 7") 4440 ( 14' 7") 4440 ( 14' 7")
Undercarriage width L 2990 ( 9' 10") 2990 ( 9' 10") 2990 ( 9' 10")
Track gauge M 2390 ( 7' 10") 2390 ( 7' 10") 2390 ( 7' 10")
Track shoe width, standard N 600 ( 2' 0") 600 ( 2' 0") 600 ( 2' 0")
Travel speed (low/high) km/hr (mph) 3.5/5.7 (2.2/3.5) 3.5/5.7 (2.2/3.5) 3.5/5.7 (2.2/3.5)
Swing speed rpm 12.2 12.2 12.2
Gradeability Degree (%) 35 (70) 35 (70) 35 (70)
Ground pressure kgf/cm² (psi) 0.45 (6.45) 0.45 (6.41) 0.45 (6.42)
Max traction force kg (lb) 21100 (46517) 21100 (46517) 21100 (46517)

2-3
Machine Serial No. : -#4560, #4880-#4922
3) HX220S LR

I(I') D
C

E
G
F

H
J M
K N
A B(L)

210S2SP10

Unit Specification
Boom 8.2 (26' 11")
Description m (ft-in)
Arm 6.30 (20' 8")
mm (in) Shoe 800 (32)
Operating weight kg (lb) 24390 (53770)
Bucket capacity (SAE heaped), standard m³ (yd³) 0.52 (0.68)
Overall length A 12030 ( 39' 6")
Overall width B 3190 ( 10' 6")
Overall height of boom C 3280 ( 10' 9")
Superstructure width D 2700 ( 8' 10")
Overall height of cab E 3000 ( 9' 10")
Ground clearance of counterweight F 1060 ( 3' 6")
Overall height of engine hood G 2380 ( 7' 10")
Overall height of handrail G' 2970 ( 9' 9")
mm (ft-in)
Minimum ground clearance H 470 ( 1' 7")
Rear-end distance I 2770 ( 9' 1")
Rear-end swing radius I' 2845 ( 9' 4")
Distance between tumblers J 3650 ( 12' 0")
Undercarriage length K 4440 ( 14' 7")
Undercarriage width L 3190 ( 10' 6")
Track gauge M 2390 ( 7' 10")
Track shoe width, standard N 800 ( 2' 7")
Travel speed (low/high) km/hr (mph) 3.66/5.76
Swing speed rpm 12.4
Gradeability Degree (%) 35 (70)
Ground pressure kgf/cm² (psi) 0.39 (5.55)
Max traction force kg (lb) 20832 (45930)

2-3-1
Machine Serial No. : -#4560, #4880-#4922
3. WORKING RANGE AND DIGGING FORCE

1) HX210S, MONO BOOM

8ft 210S2SP04A

Boom 5.68 (18' 8")

Description m (ft-in)
Arm 2.92 (9' 7") 2.00 (6' 7") 2.40 (7' 10")
Max digging reach A 9,980 ( 32' 9") 9,140 ( 30' 0") 9,500 ( 31' 2")
Max digging reach on ground A' 9,820 ( 32' 3") 8,960 ( 29' 5") 9,330 ( 30' 7")
Max digging depth B 6,730 ( 22' 1") 5,820 ( 19' 1") 6,220 ( 20' 5")
Max digging depth (8 ft level) B' 6,560 ( 21' 6") 5,580 ( 18' 4") 6,010 ( 19' 9")
mm (ft-in)
Max vertical wall digging depth C 6,280 ( 20' 7") 5,280 ( 17' 4") 5,720 ( 18' 9")
Max digging height D 9,600 ( 31' 6") 9,140 ( 30' 0") 9,340 ( 30' 8")
Max dumping height E 6,780 ( 22' 3") 6,330 ( 20' 9") 6,520 ( 21' 5")
Min swing radius F 3,670 ( 12' 0") 3,750 ( 12' 4") 3,740 ( 12' 3")
kN 133.4 133.4 133.4
kgf SAE 13600 13600 13600
lbf 29980 29980 29980
Bucket digging force
kN 152.0 152.0 152.0
kgf ISO 15500 15500 15500
lbf 34170 34170 34170
kN 102.0 144.2 119.6
kgf SAE 10400 14700 12200
lbf 22930 32410 26900
Arm digging force
kN 106.9 151.0 125.5
kgf ISO 10900 15400 12800
lbf 24030 33950 28220

2-4
Machine Serial No. : -#4560, #4880-#4922
2) HX220S, MONO BOOM

8ft
210S2SP04A

Boom 5.68 (20' 6")

Description m (ft-in)
Arm 2.92 (9' 7") 2.00 (6' 7") 2.40 (7' 10")
Max digging reach A 9,980 ( 32' 9") 9,140 ( 30' 0") 9,500 ( 31' 2")
Max digging reach on ground A' 9,820 ( 32' 3") 8,960 ( 29' 5") 9,330 ( 30' 7")
Max digging depth B 6,730 ( 22' 1") 5,820 ( 19' 1") 6,220 ( 20' 5")
Max digging depth (8 ft level) B' 6,560 ( 21' 6") 5,580 ( 18' 4") 6,010 ( 19' 9")
mm (ft-in)
Max vertical wall digging depth C 6,280 ( 20' 7") 5,280 ( 17' 4") 5,720 ( 18' 9")
Max digging height D 9,600 ( 31' 6") 9,140 ( 30' 0") 9,340 ( 30' 8")
Max dumping height E 6,780 ( 22' 3") 6,330 ( 20' 9") 6,520 ( 21' 5")
Min swing radius F 3,670 ( 12' 0") 3,750 ( 12' 4") 3,740 ( 12' 3")
kN 133.4 133.4 133.4
kgf SAE 13600 13600 13600
lbf 29980 29980 29980
Bucket digging force
kN 152.0 152.0 152.0
kgf ISO 15500 15500 15500
lbf 34170 34170 34170
kN 102.0 144.2 119.6
kgf SAE 10400 14700 12200
lbf 22930 32410 26900
Arm digging force
kN 106.9 151.0 125.5
kgf ISO 10900 15400 12800
lbf 24030 33950 28220

2-4-1
Machine Serial No. : -#4560, #4880-#4922
3) HX220S LR

A
A'
F

D
E
C
B'
B

8ft
210S2SP11

Boom 8.2 (26' 11")

Description m (ft-in)
Arm 6.30 (20' 8")
Max digging reach A 15220 ( 49' 11")
Max digging reach on ground A' 15120 ( 49' 7")
Max digging depth B 11760 ( 38' 7")
Max digging depth (8 ft level) B' 11650 ( 38' 3")
mm (ft-in)
Max vertical wall digging depth C 9610 ( 31' 6")
Max digging height D 12550 ( 41' 2")
Max dumping height E 10280 ( 33' 9")
Min swing radius F 4870 ( 16' 0")
kN 72.6
kgf SAE 7400
lbf 16310
Bucket digging force
kN 83.4
kgf ISO 8500
lbf 18740
kN 49.0
kgf SAE 5000
lbf 11020
Arm digging force
kN 50.0
kgf ISO 5100
lbf 11240

2-4-2
Machine Serial No. : -#4560, #4880-#4922
4. WEIGHT

HX210S HX220S
Item
kg lb kg lb
Upperstructure assembly 8950 19730 ←
Main frame weld assembly 2600 5730 ←
Engine assembly 437 963 ←
Main pump assembly 120 265 ←
Main control valve assembly 200 440 ←
Swing motor assembly 190 420 ←
Hydraulic oil tank assembly 240 530 ←
Fuel tank assembly 195 430 ←
Counterweight 3600 7940 ←
Cab assembly 310 680 ←
Lower chassis assembly 8060 17770 8700 19180
Track frame weld assembly 2545 5611 2720 6000
Swing bearing 290 639 ←
Travel motor assembly 305 670 ←
Turning joint 55 120 ←
Track recoil spring 140 309 ←
Idler 151 333 ←
Carrier roller 21 46 ←
Track roller 48 106 ←
Track-chain assembly (600 mm standard triple grouser shoe) 1353 2983 1356 2989

Front attachment assembly (5.68 m boom, 2.92 m arm,

4030 8880 ←
0.87 m3 SAE heaped bucket)

5.68 m boom assembly 1520 3350 ←

2.92 m arm assembly 750 1650 ←
0.92 m3 SAE heaped bucket 765 1690 ←
Boom cylinder assembly 180 400 ←
Arm cylinder assembly 290 640 ←
Bucket cylinder assembly 175 390 ←
Bucket control link assembly 170 370 ←

2-5
Machine Serial No. : -#4560, #4880-#4922
5. LIFTING CAPACITIES

Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger

MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HX210S
BOOM 5680 2000 3600 600 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *5710 *5710 5.00
(24.6 ft) lb *12590 *12590 (16.4)
6.0 m kg *5450 4330 *5520 3920 6.35
(19.7 ft) lb *12020 9550 *12170 8640 (20.8)
4.5 m kg *6890 6510 *5800 4200 4900 3170 7.14
(14.8 ft) lb *15190 14350 *12790 9260 10800 6990 (23.4)
3.0 m kg *8680 5970 6260 3990 4440 2860 4400 2830 7.55
(9.8 ft) lb *19140 13160 13800 8800 9790 6310 9700 6240 (24.8)
1.5 m kg 6040 3790 4360 2780 4240 2710 7.64
(4.9 ft) lb 13320 8360 9610 6130 9350 5970 (25.1)
0.0 m kg 9190 5450 5910 3670 4370 2770 7.43
(0.0 ft) lb 20260 12020 13030 8090 9630 6110 (24.4)
-1.5 m kg 9210 5460 5900 3660 4880 3080 6.88
(-4.9 ft) lb 20300 12040 13010 8070 10760 6790 (22.6)
-3.0 m kg *12380 10760 *9130 5600 6190 3880 5.90
(-9.8 ft) lb *27290 23720 *20130 12350 13650 8550 (19.4)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult your HD Hyundai Construction Equipment dealer regarding the lifting capacities for
specific work tools and attachments.
Failure to comply to the rated load can cause possible personal injury or property damage.
Make adjustments to the rated load as necessory for non-standard configurations.

2-6
Machine Serial No. : -#4560, #4880-#4922
Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HX210S
BOOM 5680 2400 3600 600 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *5080 4920 5.58
(24.6 ft) lb *11200 10850 (18.3)
6.0 m kg *5000 4380 *4620 3500 6.82
(19.7 ft) lb *11020 9660 *10190 7720 (22.4)
4.5 m kg *6340 *6340 *5440 4240 4530 2930 4480 2890 7.55
(14.8 ft) lb *13980 *13980 *11990 9350 9990 6460 9880 6370 (24.8)
3.0 m kg *8140 6060 *6230 4010 4450 2860 4060 2600 7.94
(9.8 ft) lb *17950 13360 *13730 8840 9810 6310 8950 5730 (26.1)
1.5 m kg 9390 5620 6040 3790 4340 2760 3920 2490 8.03
(4.9 ft) lb 20700 12390 13320 8360 9570 6080 8640 5490 (26.3)
0.0 m kg 9160 5420 5880 3650 4270 2690 4020 2540 7.83
(0.0 ft) lb 20190 11950 12960 8050 9410 5930 8860 5600 (25.7)
-1.5 m kg *10830 10370 9130 5390 5840 3610 4430 2790 7.31
(-4.9 ft) lb *23880 22860 20130 11880 12870 7960 9770 6150 (24.0)
-3.0 m kg *13260 10570 9250 5500 5930 3680 5420 3400 6.40
(-9.8 ft) lb *29230 23300 20390 12130 13070 8110 11950 7500 (21.0)
-4.5 m kg *7160 5790 *6330 5180 4.89
(-14.8 ft) lb *15790 12760 *13960 11420 (16.0)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult your HD Hyundai Construction Equipment dealer regarding the lifting capacities for
specific work tools and attachments.
Failure to comply to the rated load can cause possible personal injury or property damage.
Make adjustments to the rated load as necessory for non-standard configurations.

2-7
Machine Serial No. : -#4560, #4880-#4922
Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HX210S
BOOM 5680 2920 3600 600 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)

7.5 m kg *4450 4450 *3370 *3370 6.26

(24.6 ft) lb *9810 9810 *7430 *7430 (20.5)
6.0 m kg *4440 *4440 *3100 3080 7.38
(19.7 ft) lb *9790 *9790 *6830 6790 (24.2)
4.5 m kg *4960 4280 4570 2960 *3020 2590 8.07
(14.8 ft) lb *10930 9440 10080 6530 *6660 5710 (26.5)
3.0 m kg *7400 6190 *5790 4030 4450 2850 *3070 2340 8.43
(9.8 ft) lb *16310 13650 *12760 8880 9810 6280 *6770 5160 (27.7)
1.5 m kg *9130 5670 6050 3790 4320 2730 *3250 2240 8.51
(4.9 ft) lb *20130 12500 13340 8360 9520 6020 *7170 4940 (27.9)
0.0 m kg *5920 *5920 9140 5390 5850 3610 4220 2640 *3590 2280 8.32
(0.0 ft) lb *13050 *13050 20150 11880 12900 7960 9300 5820 *7910 5030 (27.3)
-1.5 m kg *6500 *6500 *10400 10130 9040 5300 5770 3530 4190 2610 3950 2470 7.84
(-4.9 ft) lb *14330 *14330 *22930 22330 19930 11680 12720 7780 9240 5750 8710 5450 (25.7)
-3.0 m kg *11120 *11120 *14170 10310 9110 5360 5800 3560 4680 2920 7.00
(-9.8 ft) lb *24520 *24520 *31240 22730 20080 11820 12790 7850 10320 6440 (23.0)
-4.5 m kg *11620 10680 *8190 5570 *6080 4080 5.65
(-14.8 ft) lb *25620 23550 *18060 12280 *13400 8990 (18.5)

Note 1. Lifting capacity are based on ISO 10567.

2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult your HD Hyundai Construction Equipment dealer regarding the lifting capacities for
specific work tools and attachments.
Failure to comply to the rated load can cause possible personal injury or property damage.
Make adjustments to the rated load as necessory for non-standard configurations.

2-8
Machine Serial No. : -#4560, #4880-#4922
Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HX220S
BOOM 5680 2000 3600 600 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *5710 *5710 5.00
(24.6 ft) lb *12590 *12590 (16.4)
6.0 m kg *5450 4820 *5520 4370 6.35
(19.7 ft) lb *12020 10630 *12170 9630 (20.8)
4.5 m kg *6880 *6880 *5800 4690 5520 3550 7.14
(14.8 ft) lb *15170 *15170 *12790 10340 12170 7830 (23.4)
3.0 m kg *8680 6730 *6530 4470 5010 3200 4960 3170 7.55
(9.8 ft) lb *19140 14840 *14400 9850 11050 7050 10930 6990 (24.8)
1.5 m kg 6860 4270 4930 3120 4800 3040 7.64
(4.9 ft) lb 15120 9410 10870 6880 10580 6700 (25.1)
0.0 m kg *10510 6190 6730 4150 4950 3120 7.43
(0.0 ft) lb *23170 13650 14840 9150 10910 6880 (24.4)
-1.5 m kg *10220 6210 6720 4140 5530 3470 6.88
(-4.9 ft) lb *22530 13690 14820 9130 12190 7650 (22.6)
-3.0 m kg *12380 *12380 *9130 6350 *6670 4360 5.91
(-9.8 ft) lb *27290 *27290 *20130 14000 *14700 9610 (19.4)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult your HD Hyundai Construction Equipment dealer regarding the lifting capacities for
specific work tools and attachments.
Failure to comply to the rated load can cause possible personal injury or property damage.
Make adjustments to the rated load as necessory for non-standard configurations.

2-9
Machine Serial No. : -#4560, #4880-#4922
Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HX220S
BOOM 5680 2400 3600 600 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *5080 *5080 5.58
(24.6 ft) lb *11200 *11200 (18.3)
6.0 m kg *5000 4870 *4620 3910 6.81
(19.7 ft) lb *11020 10740 *10190 8620 (22.4)
4.5 m kg *6340 *6340 *5440 4720 *4990 3280 *4490 3240 7.55
(14.8 ft) lb *13980 *13980 *11990 10410 *11000 7230 *9900 7140 (24.8)
3.0 m kg *8130 6830 *6220 4490 5020 3200 *4580 2920 7.94
(9.8 ft) lb *17920 15060 *13710 9900 11070 7050 *10100 6440 (26.1)
1.5 m kg *9700 6370 6870 4260 4910 3100 4430 2810 8.03
(4.9 ft) lb *21380 14040 15150 9390 10820 6830 9770 6190 (26.3)
0.0 m kg *10400 6170 6710 4120 4840 3040 4550 2870 7.83
(0.0 ft) lb *22930 13600 14790 9080 10670 6700 10030 6330 (25.7)
-1.5 m kg *10820 *10820 *10330 6140 6660 4080 5020 3140 7.31
(-4.9 ft) lb *23850 *23850 *22770 13540 14680 8990 11070 6920 (24.0)
-3.0 m kg *13260 12250 *9500 6250 6750 4160 6160 3830 6.41
(-9.8 ft) lb *29230 27010 *20940 13780 14880 9170 13580 8440 (21.0)
-4.5 m kg *7160 6550 *6330 5840 4.89
(-14.8 ft) lb *15790 14440 *13960 12870 (16.0)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult your HD Hyundai Construction Equipment dealer regarding the lifting capacities for
specific work tools and attachments.
Failure to comply to the rated load can cause possible personal injury or property damage.
Make adjustments to the rated load as necessory for non-standard configurations.

2-9-1
Machine Serial No. : -#4560, #4880-#4922
Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HX220S
BOOM 5680 2920 3600 600 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)

7.5 m kg *4450 *4450 *3370 *3370 6.26

(24.6 ft) lb *9810 *9810 *7430 *7430 (20.5)
6.0 m kg *4440 *4440 *3100 *3100 7.38
(19.7 ft) lb *9790 *9790 *6830 *6830 (24.2)
4.5 m kg *4950 4770 *4700 3310 *3020 2900 8.07
(14.8 ft) lb *10910 10520 *10360 7300 *6660 6390 (26.5)
3.0 m kg *7390 6960 *5790 4520 5030 3200 *3070 2640 8.43
(9.8 ft) lb *16290 15340 *12760 9960 11090 7050 *6770 5820 (27.7)
1.5 m kg *9130 6430 *6670 4270 4890 3080 *3250 2530 8.51
(4.9 ft) lb *20130 14180 *14700 9410 10780 6790 *7170 5580 (27.9)
0.0 m kg *5920 *5920 *10130 6130 6680 4090 4790 2990 *3590 2580 8.32
(0.0 ft) lb *13050 *13050 *22330 13510 14730 9020 10560 6590 *7910 5690 (27.3)
-1.5 m kg *6500 *6500 *10390 *10390 *10340 6050 6590 4010 4750 2950 *4200 2790 7.84
(-4.9 ft) lb *14330 *14330 *22910 *22910 *22800 13340 14530 8840 10470 6500 *9260 6150 (25.7)
-3.0 m kg *11110 *11110 *14180 11990 *9820 6110 6620 4040 5310 3300 7.01
(-9.8 ft) lb *24490 *24490 *31260 26430 *21650 13470 14590 8910 11710 7280 (23.0)
-4.5 m kg *11620 *11620 *8200 6330 *6080 4600 5.66
(-14.8 ft) lb *25620 *25620 *18080 13960 *13400 10140 (18.6)

Note 1. Lifting capacity are based on ISO 10567.

2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult your HD Hyundai Construction Equipment dealer regarding the lifting capacities for
specific work tools and attachments.
Failure to comply to the rated load can cause possible personal injury or property damage.
Make adjustments to the rated load as necessory for non-standard configurations.

2-9-2
 Machine Serial No. : -#4560, #4880-#4922
Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
HX220S MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
LR BOOM 8200 6300 5300 800 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) 9.0 m (29.5 ft) 10.5 m (34.4 ft) 12.0 m (39.4 ft) 13.5 m (44.3 ft) Capacity Reach

height (A)
m (ft)

10.5m kg *1210 *1210 *900 *900 10.88

34.4ft lb *2670 *2670 *1980 *1980 (35.7)
9.0m kg *850 *850 11.94
29.5ft lb *1870 *1870 (39.2)
7.5m kg *1910 *1910 *1440 *1440 *820 *820 12.73
24.6ft lb *4210 *4210 *3170 *3170 *1810 *1810 (41.8)
6.0m kg *2030 *2030 *1810 *1810 *820 *820 13.31
19.7ft lb *4480 *4480 *3990 *3990 *1810 *1810 (43.7)
4.5m kg *2330 *2330 *2220 *2220 *2110 1900 *1080 *1080 *830 *830 13.70
14.8ft lb *5140 *5140 *4890 *4890 *4650 4190 *2380 *2380 *1830 *1830 (45.0)
3.0m kg *3030 *3030 *2680 *2680 *2450 2320 *2300 1820 *1370 *1370 *860 *860 13.92
9.8ft lb *6680 *6680 *5910 *5910 *5400 5110 *5070 4010 *3020 *3020 *1900 *1900 (45.7)
1.5m kg *2840 *2840 *6410 *6410 *4540 *4540 *3600 *3600 *3050 2800 *2700 2180 *2470 1730 *1520 1380 *910 *910 13.97
4.9ft lb *6260 *6260 *14130 *14130 *10010 *10010 *7940 *7940 *6720 6170 *5950 4810 *5450 3810 *3350 3040 *2010 *2010 (45.8)
0.0m kg *2450 *2450 *6310 *6310 *5340 4570 *4120 3380 *3400 2600 *2950 2060 *2640 1650 *1500 1330 *980 *980 13.85
0.0ft lb *5400 *5400 *13910 *13910 *11770 10080 *9080 7450 *7500 5730 *6500 4540 *5820 3640 *3310 2930 *2160 *2160 (45.5)
-1.5m kg *2020 *2020 *3010 *3010 *5640 *5640 *5920 4250 *4540 3160 *3710 2450 *3160 1950 2640 1580 *1200 *1200 *1080 *1080 13.57
-4.9ft lb *4450 *4450 *6640 *6640 *12430 *12430 *13050 9370 *10010 6970 *8180 5400 *6970 4300 5820 3480 *2650 *2650 *2380 *2380 (44.5)
-3.0m kg *2900 *2900 *3830 *3830 *6080 *6080 *6270 4080 *4830 3010 3910 2340 3140 1880 2600 1540 *1220 *1220 13.11
-9.8ft lb *6390 *6390 *8440 *8440 *13400 *13400 *13820 8990 *10650 6640 8620 5160 6920 4140 5730 3400 *2690 *2690 (43.0)
-4.5m kg *3820 *3820 *4830 *4830 *7050 6110 *6400 4020 *4970 2950 3850 2290 3110 1850 *2410 1530 *1420 *1420 12.45
-14.8ft lb *8420 *8420 *10650 *10650 *15540 13470 *14110 8860 *10960 6500 8490 5050 6860 4080 *5310 3370 *3130 *3130 (40.9)
-6.0m kg *4830 *4830 *6000 *6000 *8460 6210 *6300 4050 *4940 2950 3860 2300 3130 1860 *1750 1650 11.56
-19.7ft lb *10650 *10650 *13230 *13230 *18650 13690 *13890 8930 *10890 6500 8510 5070 6900 4100 *3860 3640 (37.9)
-7.5m kg *5980 *5980 *7440 *7440 *7880 6400 *5940 4160 *4690 3030 *3780 2370 *2330 1980 10.37
-24.6ft lb *13180 *13180 *16400 *16400 *17370 14110 *13100 9170 *10340 6680 *8330 5220 *5140 4370 (34.0)
-9.0m kg *9320 *9320 *6820 6700 *5210 4360 *4070 3200 *3240 2620 8.77
-29.5ft lb *20550 *20550 *15040 14770 *11490 9610 *8970 7050 *7140 5780 (28.8)

Note 1. Lifting capacity are based on ISO 10567.

2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult your HD Hyundai Construction Equipment dealer regarding the lifting capacities for
specific work tools and attachments.
Failure to comply to the rated load can cause possible personal injury or property damage.
Make adjustments to the rated load as necessory for non-standard configurations.

2-9-3
Machine Serial No. : -#4560, #4880-#4922
6. BUCKET SELECTION GUIDE

1) HX210S, 3600 KG COUNTERWEIGHT

General bucket Heavy duty Rock heavy duty Long reach

(without side cutter)

MONO
Capacity Width
Recommendation
Without Weight Tooth
SAE CECE
Type side 5.68 m (18' 8") Boom
Heaped heaped
cutter
2.10 m 2.4 m 2.92 m
m3 m3 mm kg
EA (6' 7") (7' 10") (9' 7")
(yd3) (yd3) (in) (lb)
Arm Arm Arm
0.92 0.80 1,082 725
5 ● ◐ ■
(1.20) (1.05) (42.6') (1,600)
General 1.10 0.96 1,320 830
5 ■ ■ ▲
bucket (1.44) (1.26) (52.0'') (1,830)
1.20 1.10 1,332 810
5 ■ ▲ ▲
(1.57) (1.44) (52.4'') (1,790)
Heavy 0.90 0.80 1,082 830
5 ● ◐ ■
duty (1.18) (1.05) (42.6'') (1,830)
0.87 0.75 1,140 900
Rock 5 ● ◐ ■
(1.14) (0.98) (44.9'') (1,980)
heavy
duty 1.20 1.00 1,410 1,030
5 ■ ▲ X
(1.57) (1.31) (55.5'') (2,270)
● Applicable for materials with density of 2100 kg/m3 (3500 lb/yd3) or less
◐ Applicable for materials with density of 1800 kg/m3 (3000 lb/yd3) or less
■ Applicable for materials with density of 1500 kg/m3 (2500 lb/yd3) or less
▲ Applicable for materials with density of 1200 kg/m3 (2000 lb/yd3) or less
X Not recommended
※ These recommendations are for general conditions and average use.
Work tools and ground conditions have effects on machine performance.
Select an optimum combination according to the working conditions and the type of work that is
being done.
Consult your HD Hyundai Construction Equipment dealer for information on selecting the
correct boom-arm
boom arm-bucket
bucket combination.

2-10
Machine Serial No. : -#4560, #4880-#4922
2) HX210S, 4200 KG COUNTERWEIGHT

General bucket Heavy duty Rock heavy duty Long reach

(without side cutter)

MONO
Capacity Width
Recommendation
Without Weight Tooth
SAE CECE
Type side 5.68 m (18' 8") Boom
Heaped heaped
cutter
2.10 m 2.4 m 2.92 m
m3 m3 mm kg
EA (6' 7") (7' 10") (9' 7")
(yd3) (yd3) (in) (lb)
Arm Arm Arm
0.92 0.80 1,082 725
5 ● ● ◐
(1.20) (1.05) (42.6') (1,600)
General 1.10 0.96 1,320 830
5 ◐ ■ ■
bucket (1.44) (1.26) (52.0'') (1,830)
1.20 1.10 1,332 810
5 ◐ ■ ▲
(1.57) (1.44) (52.4'') (1,790)
Heavy 0.90 0.80 1,082 830
5 ● ● ◐
duty (1.18) (1.05) (42.6'') (1,830)
0.87 0.75 1,140 900
Rock 5 ● ● ◐
(1.14) (0.98) (44.9'') (1,980)
heavy
duty 1.20 1.00 1,410 1,030
5 ■ ■ ▲
(1.57) (1.31) (55.5'') (2,270)
● Applicable for materials with density of 2100 kg/m3 (3500 lb/yd3) or less
◐ Applicable for materials with density of 1800 kg/m3 (3000 lb/yd3) or less
■ Applicable for materials with density of 1500 kg/m3 (2500 lb/yd3) or less
▲ Applicable for materials with density of 1200 kg/m3 (2000 lb/yd3) or less
X Not recommended
※ These recommendations are for general conditions and average use.
Work tools and ground conditions have effects on machine performance.
Select an optimum combination according to the working conditions and the type of work that is
being done.
Consult your HD Hyundai Construction Equipment dealer for information on selecting the
correct boom-arm
boom arm-bucket
bucket combination.

2-10-1
Machine Serial No. : -#4560, #4880-#4922
3) HX220S, 3600 KG COUNTERWEIGHT

General bucket Heavy duty Rock heavy duty Long reach

(without side cutter)

MONO
Capacity Width
Recommendation
Without Weight Tooth
SAE CECE
Type side 5.68 m (18' 8") Boom
Heaped heaped
cutter
2.4 m 2.92 m
m3 m3 mm kg 2.10 m
EA (7' 10") (9' 7")
(yd3) (yd3) (in) (lb) (6' 7')Arm
Arm Arm
0.92 0.80 1,082 725
5 ● ● ◐
(1.20) (1.05) (42.6') (1,600)
General 1.10 0.96 1,320 830
5 ◐ ◐ ■
bucket (1.44) (1.26) (52.0'') (1,830)
1.20 1.10 1,332 810
5 ◐ ■ ▲
(1.57) (1.44) (52.4'') (1,790)
Heavy 0.90 0.80 1,082 830
5 ● ● ◐
duty (1.18) (1.05) (42.6'') (1,830)
0.87 0.75 1,140 900
Rock 5 ● ● ◐
(1.14) (0.98) (44.9'') (1,980)
heavy
duty 1.20 1.00 1,410 1,030
5 ■ ■ ▲
(1.57) (1.31) (55.5'') (2,270)
● Applicable for materials with density of 2100 kg/m3 (3500 lb/yd3) or less
◐ Applicable for materials with density of 1800 kg/m3 (3000 lb/yd3) or less
■ Applicable for materials with density of 1500 kg/m3 (2500 lb/yd3) or less
▲ Applicable for materials with density of 1200 kg/m3 (2000 lb/yd3) or less
X Not recommended
※ These recommendations are for general conditions and average use.
Work tools and ground conditions have effects on machine performance.
Select an optimum combination according to the working conditions and the type of work that is
being done.
Consult your HD Hyundai Construction Equipment dealer for information on selecting the
correct boom-arm
boom arm-bucket
bucket combination.

2-10-2
Machine Serial No. : -#4560, #4880-#4922
4) HX220S, 4200 KG COUNTERWEIGHT

General bucket Heavy duty Rock heavy duty Long reach

(without side cutter)

MONO
Capacity Width
Recommendation
Without Weight Tooth
SAE CECE
Type side 5.68 m (18' 8") Boom
Heaped heaped
cutter
2.10 m 2.4 m 2.92 m
m3 m3 mm kg
EA (6' 7") (7' 10") (9' 7")
(yd3) (yd3) (in) (lb)
Arm Arm Arm
0.92 0.80 1,082 725
5 ● ● ●
(1.20) (1.05) (42.6') (1,600)
General 1.10 0.96 1,320 830
5 ● ◐ ■
bucket (1.44) (1.26) (52.0'') (1,830)
1.20 1.10 1,332 810
5 ◐ ◐ ■
(1.57) (1.44) (52.4'') (1,790)
Heavy 0.90 0.80 1,082 830
5 ● ● ●
duty (1.18) (1.05) (42.6'') (1,830)
0.87 0.75 1,140 900
Rock 5 ● ● ●
(1.14) (0.98) (44.9'') (1,980)
heavy
duty 1.20 1.00 1,410 1,030
5 ◐ ■ ■
(1.57) (1.31) (55.5'') (2,270)
● Applicable for materials with density of 2100 kg/m3 (3500 lb/yd3) or less
◐ Applicable for materials with density of 1800 kg/m3 (3000 lb/yd3) or less
■ Applicable for materials with density of 1500 kg/m3 (2500 lb/yd3) or less
▲ Applicable for materials with density of 1200 kg/m3 (2000 lb/yd3) or less
X Not recommended
※ These recommendations are for general conditions and average use.
Work tools and ground conditions have effects on machine performance.
Select an optimum combination according to the working conditions and the type of work that is
being done.
Consult your HD Hyundai Construction Equipment dealer for information on selecting the
correct boom-arm
boom arm-bucket
bucket combination.

2-10-3
Machine Serial No. : -#4560, #4880-#4922
5) HX220S, 5300 KG COUNTERWEIGHT

General bucket Heavy duty Rock heavy duty Long reach

(without side cutter)

MONO L/Reach
Capacity Width
Recommendation
Without Weight Tooth 8.2 m
SAE CECE
Type side 5.68 m (18' 8") Boom (26' 11")
Heaped heaped
cutter Boom
2.10 m 2.4 m 2.92 m 6.3 m
m3 m3 mm kg
EA (6' 7") (7' 10") (9' 7") (20' 8")
(yd3) (yd3) (in) (lb)
Arm Arm Arm Arm
0.92 0.80 1,082 725
5 ● ● ● X
(1.20) (1.05) (42.6') (1,600)
General 1.10 0.96 1,320 830
5 ● ● ● X
bucket (1.44) (1.26) (52.0'') (1,830)
1.20 1.10 1,332 810
5 ● ● ◐ X
(1.57) (1.44) (52.4'') (1,790)
Heavy 0.90 0.80 1,082 830
5 ● ● ● X
duty (1.18) (1.05) (42.6'') (1,830)
0.87 0.75 1,140 900
Rock 5 ● ● ● X
(1.14) (0.98) (44.9'') (1,980)
heavy
duty 1.20 1.00 1,410 1,030
5 ● ◐ ◐ X
(1.57) (1.31) (55.5'') (2,270)
0.52 0.45 935 460
LR 5 X X X ■
(0.68) (0.59) (36.8'') (1,010)
● Applicable for materials with density of 2100 kg/m3 (3500 lb/yd3) or less
◐ Applicable for materials with density of 1800 kg/m3 (3000 lb/yd3) or less
■ Applicable for materials with density of 1500 kg/m3 (2500 lb/yd3) or less
▲ Applicable for materials with density of 1200 kg/m3 (2000 lb/yd3) or less
X Not recommended
※ These recommendations are for general conditions and average use.
Work tools and ground conditions have effects on machine performance.
Select an optimum combination according to the working conditions and the type of work that is
being done.
Consult your HD Hyundai Construction Equipment dealer for information on selecting the
correct boom-arm
boom arm-bucket
bucket combination.

2-10-4
Machine Serial No. : -#4560, #4880-#4922
7. UNDERCARRIAGE

1) TRACKS
X-leg type center frame is integrally welded with reinforced box-section track frames. The design
includes dry tracks, lubricated rollers, idlers, sprockets, hydraulic track adjusters with shock
absorbing springs, and assembled track-type tractor shoes with triple grousers.

2) TYPES OF SHOES
Triple grouser

Model Shapes

Shoe width mm (in) 600 (24) - - 800 (32)

Operating weight kg (lb) 20830 (45920) - - 21380 (47140)

HX210S
Ground pressure kgf/cm2 (psi) 0.48 (6.81) - - 0.42 (5.99)

Overall width mm (ft-in) 2800 (9' 2") - - 3000 (9' 10")

Shoe width mm (in) 600 (24)★ 600 (24) 700 (28) 800 (32)

Operating weight kg (lb) 21260 (46870) 21450 (47290) 21750 (47950) 22040 (48590)
HX220S
Ground pressure kgf/cm2 (psi) 0.45 (6.45) 0.46 (6.51) 0.40 (5.56) 0.35 (5.02)

Overall width mm (ft-in) 2990 (9' 10") 2800 (9' 2") 3090 (10' 2") 3190 (10' 6")
★ : 8.5 T

3) NUMBER OF ROLLERS AND SHOES ON EACH SIDE

Item Quantity
Carrier rollers 2 EA
HX210S 7 EA
Track rollers
HX220S 9 EA
HX210S 46 EA
Track shoes
HX220S 49 EA

2-11
Machine Serial No. : -#4560, #4880-#4922
4) SELECTION OF TRACK SHOE
Suitable track shoes should be selected according to operating conditions.
Method of selecting shoes
Confirm the category from the list of applications in table 2,
2 then use table 1 to select the shoe.
Wide shoes (categories B and C) have limitations on applications. Before using wide shoes, check
the precautions, then investigate and study the operating conditions to confirm if these shoes are
suitable.
Select the narrowest shoe possible to meet the required flotation and ground pressure.
Application of wider shoes than recommendations will cause unexpected problem such as bending
of shoes, crack of link, breakage of pin, loosening of shoe bolts and the other various problems.

※ Table 1
Track shoe Specification Category

600 mm triple grouser Standard A

700 mm triple grouser Option B
800 mm triple grouser Option C

※ Table 2
Category Applications Precautions

Rocky ground, · Travel at low speed on rough ground with large obstacles such as boul-
A river beds, ders or fallen trees or a wide range of general civil engineering work
normal soil

Normal soil, · These shoes cannot be used on rough ground with large obstacles
soft ground such as boulders or fallen trees
B · Travel at high speed only on flat ground
· Travel slowly at low speed if it is impossible to avoid going over obsta-
cles

Extremely soft ground · Use the shoes only in the conditions that the machine sinks and it is
(swampy ground) impossible to use the shoes of category A or B
· These shoes cannot be used on rough ground with large obstacles
C such as boulders or fallen trees
· Travel at high speed only on flat ground
· Travel slowly at low speed if it is impossible to avoid going over obsta-
cles

2-12
Machine Serial No. : -#4560, #4880-#4922
8. SPECIFICATIONS FOR MAJOR COMPONENTS
1) ENGINE
Item Specification
Model HD Hyundai Construction Equipment 6BTAA-5.9 (HM5.9)
4-cycle, turbocharged, charge air cooled,
Type
mechanical controlled diesel engine
Cooling method Water cooled
Number of cylinders and arrangement 6 cylinders, in-line
Firing order 1-5-3-6-2-4
Combustion chamber type Direct injection type
Cylinder bore×stroke 102×120 mm (4.02 "×4.72 ")
Piston displacement 5900 cc (360 cu in)
Compression ratio 17.3 : 1
Rated gross horse power (SAE J1995) 148 Hp at 2000rpm (110 kW at 2000 rpm)
Rated net horse power (SAE J1349) 145 Hp at 2000 rpm (108 kW at 2000 rpm)
Maximum torque at 1300 rpm 64 kgf· m (463 lbf·ft)
14ℓ (3.8 U.S. gal) : -#1289
Engine oil quantity
20ℓ (5.3 U.S. gal) : #1290-
Dry weight 437 kg (963 lb)
High idling speed 2250 + 50 rpm
Low idling speed 800 ± 100 rpm
Rated fuel consumption 95 g/Hp·hr at 1200 rpm
Starting motor Lucas 24V
Alternator Lucas 24V-75A
Battery 2×12V×100Ah

2) MAIN PUMP

Item Specification
Type Variable displacement tandem axis piston pumps
Capacity 2×117 cc/rev
Maximum pressure 350 kgf/cm2 (4978 psi)
Rated oil flow 2×234ℓ/min (61.8 U.S. gpm/ 51.4 U.K. gpm)
Rated speed 2000 rpm

2-13
Machine Serial No. : -#4560, #4880-#4922
3) GEAR PUMP

Item Specification
Type Fixed displacement gear pump single stage
Capacity 15 cc/rev
Maximum pressure 40 kgf/cm2 (568 psi)
Rated oil flow 30ℓ/min (7.9 U.S. gpm/6.7 U.K. gpm)

4) MAIN CONTROL VALVE

Item Specification
Type 9 spools mono-block
Operating method Hydraulic pilot system
Main relief valve pressure 350 kgf/cm2 (4978 psi)
Overload relief valve pressure 400 kgf/cm2 (5689 psi)

5) SWING MOTOR
Item Specification
Type Two fixed displacement axial piston motor
Capacity 142.8 cc/rev
Relief pressure 265 kgf/cm2 (3894 psi)
Braking system Automatic, spring applied hydraulic released
Braking torque 63.3 kgf/cm2 (470.8 lbf·ft)
Brake release pressure 20.9~35.5 kgf/cm2 (297~505 psi)
Reduction gear type 2 - stage planetary
Swing speed 12.2rpm

6) TRAVEL MOTOR
Item Specification
Type Variable displacement axial piston motor
Relief pressure 350 kgf/cm2 (4978 psi)
Reduction gear type 2-stage planetary
Braking system Automatic, spring applied hydraulic released
Brake release pressure 13 kgf/cm2 (182 psi)
Braking torque 65.1 kgf·m (470 lbf·ft)

2-14
Machine Serial No. : -#4560, #4880-#4922
7) REMOTE CONTROL VALVE

Item Specification
Type Pressure reducing type
Minimum 6.5 kgf/cm2 (92 psi)
Operating pressure
Maximum 26 kgf/cm2 (370 psi)
Lever 61 mm (2.4 in)
Single operation stroke
Pedal 123 mm (4.84 in)

8) CYLINDER

Item Specification

Bore dia×Rod dia×Stroke Ø120×Ø85×1290 mm

Boom cylinder
Cushion Extend only
Bore dia×Rod dia×Stroke Ø140×Ø100×1510 mm
Arm cylinder
Cushion Extend and retract
Bore dia×Rod dia×Stroke Ø120×Ø85×1055 mm
Bucket cylinder
Cushion Extend only
※ Discoloration of cylinder rod can occur when the friction reduction additive of lubrication oil spreads on
the rod surface.
※ Discoloration does not cause any harmful effect on the cylinder performance.

9) SHOE
Item Width Ground pressure Link quantity Overall width
Standard 600 mm (24") 0.48 kgf/cm2 (6.81 psi) 46 2800 mm (9' 2")
HX210S
Option 800 mm (32") 0.42 kgf/cm2 (5.99 psi) 46 3000 mm (9' 10")
Standard 600 mm (24") 0.45 kgf/cm2 (6.45 psi) 49 2990 mm (9' 10")
600 mm (24") 0.46 kgf/cm2 (6.51 psi) 49 2800 mm (9' 2")
HX220S
Option 700 mm (28") 0.40 kgf/cm2 (5.56 psi) 49 3090 mm (10' 2")
800 mm (32") 0.35 kgf/cm2 (5.02 psi) 49 3190 mm (10' 6")

10) BUCKET
Capacity Tooth Width
Item
SAE heaped CECE heaped quantity Without side cutter With side cutter
STD 0.92 m3 (1.20 yd3) 0.80 m3 (1.05 yd3) 5 1150 mm (45.3") 1270 mm (50.0")
HX210S
1.20 m3 (1.57 yd3) 1.00 m3 (1.31 yd3) 5 1400 mm (55.1") 1520 mm (59.8")
HX220S OPT
◈0.90 m3 (1.18 yd3) 0.80 m3 (1.05 yd3) 5 1090 mm (42.9") -
◈ : Heavy duty bucket

2-15
Machine Serial No. : -#4560, #4880-#4922
9. RECOMMENDED OILS
HD Hyundai Construction Equipment genuine lubricating oils have been developed to offer the best
performance and service life for your equipment. These oils have been tested according to the specifi-
cations of HD Hyundai Construction Equipment and, therefore, will meet the highest safety and quality
requirements. We recommend that you use only HD Hyundai Construction Equipment genuine lubri-
cating oils and grease officially approved by HD Hyundai Construction Equipment.

Service Ambient temperature˚C(˚F)

Capacity
Kind of fluid
point ℓ (U.S. gal) -50 -30 -20 -10 0 10 20 30 40
(-58) (-22) (-4) (14) (32) (50) (68) (86) (104)

★SAE 0W-40
14 (3.8) ★SAE 0W-30
Engine ★2 : -#1289
Engine oil SAE 5W-30
oil pan 20 (5.3)
: #1290- SAE 10W-30
SAE 15W-40

Swing
6.2 (1.6) ★SAE 75W-90
drive
Gear oil
Final 4.5×2 SAE 80W-90
drive (1.2×2)
★ISO VG 15
Tank : 160
Hydraulic (42.3) ISO VG 32
Hydraulic oil
tank System : 275 ISO VG 46
(72.6)
ISO VG 68

★ASTM D975 NO.1

Fuel tank Diesel fuel 340 (89.8)
ASTM D975 NO.2

Fitting
★NLGI NO.1
(grease Grease As required
nipple) NLGI NO.2
Mixture of
Radiator Ethylene glycol base permanent type (50 : 50)
antifreeze
(reservoir 31 (8.2)
and soft ★Ethylene glycol base permanent type (60 : 40)
tank)
water★1
SAE : Society of Automotive Engineers ★ : Cold region
API : American Petroleum Institute Russia, CIS, Mongolia
ISO : International Organization for Standardization ★1 : Soft water
NLGI : National Lubricating Grease Institute City water or distilled water
ASTM : American Society of Testing and Material ★2 : Meets or exceeds
API CI-4 grade
※ Using any lubricating oils other than HD Hyundai Construction Equipment genuine products may lead to
a deterioration of performance and cause damage to major components.
※ Do not mix HD Hyundai Construction Equipment genuine oil with any other lubricating oil as it may result
in damage to the systems of major components.
※ For HD Hyundai Construction Equipment genuine lubricating oils and grease for use in regions with
extremely low temperatures, please contact HD Hyundai Construction Equipment dealers.

2-16