GENERAL PLUMBING NOTES PLUMBING PIPES & FITTINGS REPUBLIC OF THE PHILIPINES

OFFICE OF THE BUILDING OFFICIAL

LAPU-LAPU CITY
1. ALL PLUMBING WORKS HEREIN SHALL BE EXECUTED ACCORDING TO 1. FOR WATER LINES USE, G.I. PIPES AND FITTINGS. MATERIAL BRAND IS SUPREME, APO OR
THE REQUIREMENTS OF THE PHILIPPINE NATIONAL PLUMBING CODE SUPER G.4. PIPE.
AND THE RULES AND REGULATIONS OF THE EXISTING LOCAL CODES BABAG SPORTS COMPLEX OFFICE OF THE BUILDING OFFICIAL

FROM OPON MERCADO

AND ORDINANCES. NOTHING CONTAINED ON THE DRAWING SHALL BE
CONSTRUED AS TO CONFLICT WITH THE NATIONAL AND LOCAL
ORDINANCES OR LAWS GOVERNING THE IMPLEMENTATION OF THE
2. BRONZE GATE VALVES OF 125 LBS. WORKING PRESSURE, U.S. MADE. MATERIAL BRAND,
PRICE PFISTER USA OR KILZ JAPAN OR CRANE. N
PLUMBING WORKS. 3. SEWER PIPES, VENT FITTINGS AND TRAPS TO USE PVC PIPES AND FITTING MATERIAL OF
NELTEX, EMERALD OR ATLANTA BRAND.
2. REFER TO ALL ARCHITECTURAL, STRUCTURAL, ELECTRICAL,
MECHANICAL PLANS AND SPECIFICATIONS AND INVESTIGATE ALL
4. PVC JOINT CEMENT. MATERIAL BRAND, NELTEX, EMERALD OR ATLANTA.
THIS SITE
POSSIBLE INTERFERENCE AND CONDITIONS AFFECTING THE BLK. 10 LOT 12, PARK PLACE CEBU
PLUMBING WORKS. PARKPLACE, BABAG 2 LLC
5. FLOOR DRAIN SIZE IS 100mm x 100mm STAINLESS STEEL. MATERIAL BRAND, METMA,
3. IT IS NOT INTENDED THAT DRAWINGS SHALL SHOW EVERY PIPE JAMAN OR ZURN. APPROVED BY:

FITTING, VALVE AND APPLIANCES. FURNISH AND INSTALL, IF

NECESSARY ALL ITEMS WHETHER SPECIFICALLY MENTIONED OR NOT, 6. ROOF DRAIN MATERIAL BRAND, 76mm BRASS,JAMAN BRAND,MODEL JRDD 110 BUILDING OFFICIAL DATE

OR INDICATED ON THE DRAWINGS, TO COMPLETE THE SYSTEM IN

ACCORDANCE WITH THE BEST PRACTICE OF THE PLUMBING TRADE 7. TRANSFER PUMP MATERIAL BRAND, GRUNDFOS OR GOULDS.
AND TO THE SATISFACTION OF THE ARCHITECT.
8. WATER METER MATERIAL BRAND ASAHI OR EVER.
4. PERFORM ALL LABOR IN A FIRST-CLASS, NEAT, WORKMANLIKE
MANNER BY SPECIALISTS SKILLED IN THEIR TRADES, AND SUCH 9. AIR CHAMBER TO BE PROVIDED FOR ALL WATER LINES OUTLETS ALL NECESSARY
SPECIALISTS AND THEIR WORKS SHALL BE SATISFACTORY TO THE FITTING SHALL BE PROVIDED.
ARCHITECT.

)
10. TEFLON TAPE FOR ALL WATER LINES CONNECTIONS APPLIED TO MALE THREADS ONLY.

AD
RO

TO CO
LL
(TO
BASIC MATERIALS 11. STAINLESS P-TRAP 1 1/4" FOR ORDINARY SINK. MATERIAL BRAND, SANITARY DASH OR

PY

RDOV
K EX
USA (SD).

LIN

A
PROVIDE MATERIALS THAT ARE NEW AND THAT CONFORM WITH THE

OVA
STANDARDS OF THE UNDERWRITERS LABORATORIES, INC. 12. STAINLESS STEEL SINK STRAINER MATERIAL BRAND, BIG BOY USA.

ORD
TECHNICAL DESCRIPTION

C
FOR OTHER MISCELLANEOUS REQUIRED MATERIALS NOT SPECIFICALLY

U-
13. APPLY PIONEER EPOXY FOR JOINT.

CEB
MENTIONED. PROVIDE THE BEST OF THE RESPECTIVE KIND. LINE BEARING DISTANCE
14. MAKE ALL JOINTS WATER TIGHT. FOR JOINING PIPES, USE THE FOLLOWING:
SUBMIT SAMPLES OF THE MATERIALS FOR APPROVAL AS REQUIRED BY 1-2 S 68° 29' E 10.00 M
THE ARCHITECT. A. GALVANIZED IRON AND COPPER PIPES:
CAREFULLY REAMED THREADED JOINTS. APPLY TEFLON TAPE OR PAINT WITH RED 2-3 S 21° 31' W 8.00 M
CONFORM ALL APPLICABLE PIPES AND MATERIALS FOR VARIOUS LEAD AT ALL LENGTHS.
SERVICES TO THE STANDARDS STATED HEREUNDER. 3-4 N 68° 29' W 10.00 M
B. CEMENT PIPES:
GROUT WITH CEMENT MIX ALL AROUND THE JOINTS IN A CONSISTENT MANNER. DO 4-1 N 21° 31' E 8.00 M
PLUMBING FIXTURES NOT ALLOW GROUT TO BULGE INSIDE PIPE INTERIORS 1 VICINITY MAP BLOCK NO.: 10 LOT NO: 12 LOT AREA: 80sq.m
INSTALL ALL PLUMBING FIXTURES FREE AND OPEN IN A MANNER TO C. PVC PIPES: P 01 SCALE NTS
ACCESS FOR CLEANING, FURNISHING WITH BRACKETS, CLEATS, PLATES USE APPROPRIATE COUPLERS AND GLUE AT JOINTS.
AND ANCHORS REQUIRED TO SUPPORT THE FIXTURES RIGIDLY IN PLACE.
15. THE THREADS OF DRAINAGE FITTINGS SHALL BE TAPPED TO ALLOW TWO (2) PERCENT
KEEP AWAY AT A SUFFICIENT DISTANCE BUT NOT LESS THAN 12 INCH OR 21mm/M GRADE
(12.7mm) ALL SERVICE PIPES, VALVES AND FITTINGS FROM SURFACES
AND LOCATION WHICH MAY REQUIRE FINISH COATS OR COVERING. 300
0
EXTEND THE PIPING TO ALL FIXTURES, OUTLETS AND EQUIPMENT FROM SHUT-OFFS
REQUIRED GATE VALVES INSTALLED IN EACH BRANCH NEAR RISERS.
100
PROVIDE THE ENTIRE SYSTEM WITH VALVES SO LOCATED THAT THE SYSTEM OR PORTIONS OF 00
IT CAN BE OPERATED, REPLACED AND REPAIRED, AS WELL AS AFFORDING COMPLETE
SOIL, WASTE, DRAIN & VENT PIPING CONTROL OF THE WATER SUPPLY TO EACH GROUP OF THE FIXTURES. WHEN REQUIRED, FIRE 550
0
WA
PROVIDE ALSO PRESSURE REDUCING VALVES. N 68 LL
° 29
'E
INSTALL ALL PIPING WORKS IN CONFORMITY WITH ALL PROVISIONS
REQUIRED OF THE LATEST EDITION OF THE PHILIPPINES AND APPLICABLE

0
550
REQUIREMENTS OF EXISTING LOCAL CODES. 150
TRAPS 0

0
EXCAVATE TO REQUIRED DEPTHS AND GRADES ALL EXCAVATIONS

800

REA
1. EXCEPT FOR THE PRESENCE OF GREASE INTERCEPTOR AND OTHER DEVICES WHERE

EA
REQUIRED FOR THE INSTALLATION OF PLUMBING AND DRAINAGE SYSTEM.

ALL
THE TRAP IS AN INTEGRAL PART OF THE DESIGN, EQUIPPED WITH A TRAP EVERY

GA
WHEN ROCK IS ENCOUNTERED, EXTEND EXCAVATION TO A DEPTH 160mm.

AR
'E
EW
FIXTURE AND EQUIPMENT REQUIRING CONNECTIONS TO THE DRAINAGE SYSTEM.

° 31
BELOW THE PIPE BOTTOM AND BEFORE PIPE IS LAID, FILL SAND AND

ION

DIN
N 21
FIR
OTHER APPROVED MATERIALS.
2. SET EACH TRAP AS CLOSE AS POSSIBLE TO THE FIXTURE SERVED AND RENDER LEVEL

ENS

UIL
LAY WATER SUPPLY PIPES AND SEWERS IN SEPARATE TRENCHES. WITH RESPECT TO IT'S WATER SEAL.

GB
EXT

TIN

EA
ALL HORIZONTAL PIPING SHALL BE RUN IN PRACTICAL ALIGNMENT AND

EXIS
AT A UNIFORM GRADE OF NOT LESS THAN TWO PERCENT (2%) OR 2CM PER
CLEANOUTS

AR
0
METER TOWARDS THE POINT OF DISPOSAL.

250
LEGEND:

ION
FOR CLEANOUTS STEMMING FROM PVC, PROVIDE WITH LONG SWEEP QUARTER BENDS OR

'W
ENS

° 31
ONE OR TWO EIGHT BENDS, EXTENDED TO AN EASILY ACCESSIBLE PLACE, AND GENERALLY
CERTIFICATION

S 21
EXT
WHERE INDICATED IN THE DRAWINGS. DOWNSPOUT

AD
RO
THIS IS TO CERTIFY THAT THE SEEPAGE PITS TO BE CONSTRUCTED, EXT
AS POINTS OF DISPOSAL, FOR SANITARY DRAINAGE SYSTEM OF THE BUILDING PIPELINE ENS
ION
SHALL CONFORM TO THE MINIMUM HORIZONTAL CLEAR DISTANCE OTHERS ARE
A
AS REQUIRED BY THE 1999 REVISED NATIONAL PLUMBING CODE (TABLE B-1, PAGE 192)
DETAILED HEREUNDER. CB CATCH BASIN
1. PIPES SHALL BE INSTALLED AS INDICATED. ANY RELOCATION REQUIRED FOR PROPER S 68
° 29
EXECUTION OF OTHER TRADES SHALL BE PRIOR APPROVAL OF ARCHITECT AND THE
FIRE 'W

FROM BUILDING OR STRUCTURES 2.40 M WA

DESIGNING PLUMBING ENGINEER. LL
PROPERTY LINE ADJOINING PRIVATE PROPERTY 2.40 M
WATER SUPPLY WELL 45.70 M
STREAMS 30.50 M 2. PROPOSED SANITARY UTILITIES SHALL CONFORM TO THE ACTUAL LOCATION, DEPTH ,
TREES 3.00 M AND INVERT ELEVATIONS.
SEEPAGE PITS 3.70 M
ON-SITE DOMESTIC WATER SERVICE LINE 1.50 M 3. ALL FIXTURES SHALL BE VENTED, UNLESS OTHERWISE INDICATED.
DISTRIBUTION BOX 1.50 M 2 LOT PLAN
GUARANTEE & WARRANTY P 01 SCALE 1:50 M

CHECA MARIE G. RUBIA

THE CONTRACTOR SHALL GUARANTEE ALL MATERIALS SUPPLIED AND WORK TO BE FREE
REGISTERED MASTER PLUMBER FROM FACTORY DEFECT AND WORKMANSHIP FOR A PERIOD OF ONE (1) YEAR.

ANY MATERIAL FOUND TO BE DEFECTIVE DURING THE TIME OF CONSTRUCTION SHALL BE

REPLACED BY THE CONTRACTOR FREE OF CHARGE.

R.A.9266 Section 33 DESIGNED BY:

SEAL PROJECT TITLE APPROVED BY SHEET CONTENT AS BUILT ESTIMATE SHEET NO.
Drawing and specifications and other DRAFTED BY: TAGADIAD M. BIDDING FABRICATION

W RKS 2F E. Vaño Sr. Bldg, ML Quezon National Highway, Pusok, Lapu-lapu City 6015 Cebu Philippines
PCAB LICENSE NO.: 40922
000 - 242 - 918 - 422 :NI T . g e R T AV
CHECA MARIE G. RUBIA
REGISTERED MASTER PLUMBER

PRC. NO.: 0014425 VALIDITY : 12-05-2025

contract documents signed, stamped or sealed, as
instruments of service, are the intellectual property
and documents of the architect, whether the object
for which they are made is executed or not, if shall
be unlawful for any person to duplicate or to make
2nd FLOOR
RESIDENTIAL BUILDING EXTENSION ALEX P. DE VILLA
GENERAL NOTES
VICINITY MAP
LOT PLAN
LEGEND
DATE CRAFTED: 5-30-2025

CAD LT LICENSE:
BUILDING PERMIT

CONSTRUCTION
OWNER'S APPROVAL

PRESENTATION P-01
2 6+ , 8 8 3 7 - 8 1 3 - 2 3 - 3 6+ . son enohpe l eT
- 7 1 9 0 , 3 2 4 0 - 0 1 3 - 7 1 9 0 . son enohp l l eC
Email: troworks@outlook.com
troworks@yahoo.com
PTR NO. : - DATE : 03-24-2022
copies of said documents for use in the repetition
of and for other projects of building, whether OWNER
REVISIONS DATE REVISIONS DATE
01 02
executed partly in whole, without the written
TIN : 773-546-347-000 MINGLANILLA, CEBU consent of architect or author of said documents. LOCATION: BLK.10 LOT 12, PARKPLACE, BABAG 2, LLC ADDRESS: BLK.10 LOT 12, PARKPLACE, BABAG 2, LLC PLUMBING