CMP

CMP PRODUCTS
Industrial and Explosive Atmosphere Cable Glands and Conduit Accessories

Terminating Cables
is our Business

CALL 1300 GLANDS

Onshore – Offshore – Marine – Mining – Surface – Underground

Solutions complying with

BS 6121, EN 50262, IEC 62444, IEC & AS/NZS 60079
for all types of cables
 CMP CABLE GLAND AND CABLE CONNECTION SPECIALISTS

Leading the Way in Cable Gland Terminations

INTRODUCTION

CMP Products has an international reputation for Quality and Reliability in various sectors of Industry and is highly regarded as the Specialist in the field of
Industrial and Hazardous Area Cable Gland and Cable Connector design and manufacture.

CMP Products maintains its position as a leader in the business of terminating cables through its commitment to meeting customer needs, providing
solutions, whether standard or special, that pay close attention to the heart of application and installer requirements, and in addition by responding to ongoing
changes in standards & specification.

CMP Products industrial cable glands were originally designed and tested to conform to the British Standard BS 4121, which was superseded by BS 6121 in
1973 when the imperial conduit, or electrical thread form (measured in inches) was over taken by the metric system. Whilst new standards such as EN 50262
and IEC 62444 have more recently been introduced, which CMP Products also complies with, BS 6121 still remains a very important benchmark for users and
manufacturers around the world, due mainly to the fact that it is a more onerous construction standard than others published in the last 40 years. This will
therefore be especially relevant where a national cable gland standard isn’t available. The tables below show the maximum cable entry bore size and tolerances
permitted through the range of BS 6121 cable gland sizes. CMP Products recommends that customers check the maximum cable diameter allowed through
the bore of any cable gland before selections are made.

Cable Gland Bore Sizes Referenced in BS 6121 Part 1 : 1989, Tables 1 to 6

Cable Gland Size 16 20S 20 25 32 40
Entry Thread Size M20 OR M16 M20 M20 M25 M32 M40
Bore Size 8.7 11.7 14.0 20.0 26.3 32.2
Permitted Tolerance + 0.3mm + 0.3mm + 0.3mm + 0.3mm + 0.5mm + 0.5mm
Maximum Bore Size 9.0 12.0 14.3 20.3 26.8 32.7

Cable Gland Size 50S 50 63S 63 75S 75

Entry Thread Size M50 M50 M63 M63 M75 M75
Bore Size 38.2 44.1 50.1 56.0 62.0 68.0
Permitted Tolerance + 0.5mm + 0.5mm + 0.5mm + 0.5mm + 0.5mm + 0.5mm
Maximum Bore Size 38.7 44.6 50.6 56.5 62.5 68.5

CMP Products remains in constant touch with the changes in development of national and international standards, which products and equipment need to be
designed and manufactured to in order to ensure compliance of installations. CMP Products also has a wealth of international experience of installation
practices and can help users to make informed decisions that comply with local requirements such as the AS/NZS 60079.14:2009 standard covering
“Explosive atmospheres - Electrical installations design, selection and erection”

The adoption and integration of IEC standards into a selection of various national standards around the world, including the Australian Standards, together
with the introduction, and wide spread acceptance, of the IEC Ex approval scheme (IEC Ex 02) gives a new impetus to progressive manufacturers like CMP
Products. It is now possible to supply cable connecting solutions that are certified under both the ATEX and IEC Ex approval systems thereby providing the
opportunity for dual marking of products that can be installed in global situations.

In its range of hazardous area (type ‘d) cable glands, the installation technique is fundamentally different from most other rival products. The tightening of the
flameproof (gas tight) sealing ring in CMP cable glands is separated from the tightening of the metallic armour, in the case of armoured cables. Making the two
actions independent of each other ensures that there is more control over what happens to the cable during installation, and also gives the installer a better
idea of whether he has completed the task correctly at the first time of asking.

The CMP Products cable gland portfolio is an extensive one with solutions for Industrial, Marine, Surface and Underground Mining, Onshore and Offshore
Hazardous Areas. This Short Form Catalogue contains a brief insight into a selection of products commonly used across Australia. A more comprehensive
CMP technical product catalogue TPC188 is available on request containing a wide variety of products used for terminating various types of cable that may be
encountered under local installation codes and wiring regulations, IEC Standards, & NEC wiring rules.

CMP Products manufactures a greater variety of cable glands and more volume of product than any of its rivals. Here are some of the key elements that the
CMP Products range offers;
Materials : Standard is Electroless Nickel Plated Brass. All metallic components are manufactured from the same material grade Brass alloy 385 to AS/NZS
SFC 3001 Issue 2 : 06/12

1567 or CuZn39Pb3 to EN 12168. Plain brass is available on request.

Alternative materials include Stainless Steel Grade 316, Copper Free Aluminium and Nylon

Thread Forms : Standard is Metric (ISO 965). Standard thread sizes from M16 to M130
Alternatives include a wide range of sizes of NPT, BSPP, BSPT, Imperial Conduit (ET), PG, NPS.

Other Products include ;

Cable glands with Low Smoke & Fume (LSF) Halogen Free materials, Insulated Cable Entry, Integral Heavy Duty Earth Lug, Conduit Connection facility,
Insulated Adaptors, Male to Male Adaptors, Female to Female Adaptors, Unions.

CMP Products - a Global Solutions Provider of Cable Glands, Cable Connectors, and Complementary
Cable Related Products & Conduit Accessories
1 www.cmp-products.com.au
 CABLE GLAND AND CABLE CONNECTION SPECIALISTS CMP

CONTENTS

CONTENTS
Introduction 1

Contents 2

A2 Industrial / Mining Cable Glands for unarmoured cables 3

CWD Industrial / Mining Cable Glands for Single Wire Armour

4
(SWA) cables
TMC Industrial / Mining Cable Glands for Variable Speed Drive (VSD)
5
Cables with Copper Tape Screens or cables with Metallic Sheath
A2F Ex d, Ex e, Ex nR Explosive Atmosphere Cable Glands for unarmoured
6
cables

E1FW Ex d, Ex e, Ex nR Explosive Atmosphere Cable Glands for Single

7
Wire Armour (SWA) cables
T3CDS Ex d, Ex e, Ex nR Explosive Atmosphere Deluge Proof Cable
8
Glands for SWA, Braided, STA & PWA cables

PXSS2K Ex d, Ex e, Ex nR Explosive Atmosphere Compound Barrier Cable

9
Glands for unarmoured cables

PX2KW Ex d, Ex e, Ex nR Explosive Atmosphere Compound Barrier Cable

10
Glands for Single Wire Armour (SWA) cables

Accessories; Locknuts, Earth Tags, Sealing Washers, Serrated Washers, 11

Shrouds

747, 757, 767 Stopper Plugs

737, 787 Adaptors, Reducers 12
781 Breather / Drain Plugs

737 Adaptor & Reducer Selection Tables 13

AS/NZS 5000.1 and AS/NZS 5000.2 Cable Gland Selection Tables 14
SFC 3001 Issue 2 : 06/12

Please consult CMP Products for any requirements not shown in this publication.
www.cmp-products.com.au 2
 CMP CABLE GLAND AND CABLE CONNECTION SPECIALISTS

A2 CABLE GLAND A2 Industrial Cable Gland

A2 INDUSTRIAL CABLE GLANDS FOR UNARMOURED CABLES

CMP A2 Type Nickel Plated Brass indoor and outdoor cable gland for use with all types of
Unarmoured cable, providing mechanical cable retention and an environmental seal on the cable
outer sheath.

The CMP A2 range of industrial cable glands is designed and tested to BS 6121:Part 1:1989, meets
or surpasses the requirements of EN 50262 :1999 and IEC 62444 : 2010, and is produced from
Brass grade CuZn39Pb3 (CW614N) to EN12168 equal to alloy 385 to AS/NZS 1567 with Electroless
Nickel Plating as standard. All metallic cable gland components are manufactured from the same
grade of material. Brass locknuts are produced in the same CU Zn39PB3 grade as the cable gland.
Other materials including Aluminium are also available in this standard design.

C
TECHNICAL DATA
A
Type A2

Design Specification BS 6121:Part 1:1989, EN 50262:1999, IEC 62444 : 2010

Mechanical Classifications Retention = Class B, Impact = Level 8,

Lloyds Approval Number 01/00171

E
ABS Approval Number 01-LD 234401-PDA

Continuous Operating Temperature -60°C to +150°C

Ingress Protection Rating IP66, IP67, IP68

Ingress Protection Document 5046 C549D F

Deluge Protection Compliance DTS01 : 91

Deluge Protection Document 5046 C549-D

Standard Cable Gland Material Electroless Nickel Plated Brass

Alternative Cable Gland Material Stainless Steel, Aluminium

Seal Material CMP Formulated Thermoplastic Elastomer

Cable Type Unarmoured D

Sealing Technique CMP Displacement Seal

Sealing Area(s) Cable Outer Sheath Note: Entry Thread Sealing Washer
and Locknut included as standard
Optional Accessories Adaptor/Reducer, Earth Tag, Serrated Washer, Shroud

Cable Gland Selection Table

Minimum Overall Cable Across Across Nominal Cable

Cable Diameter Flats Corners Ordering
Standard Metric Thread Protrusion Shroud Gland
Gland ‘A’ ‘D’ ‘D’ Reference
Entry Threads Length Length Reference* Weight
Size
‘C’ ‘E’ ‘F’ (Kgs)
Min Max Max
20S/16 M20 10.0 3.1 8.7 24.0 26.6 21.0 20S16A21RA5/A PVC04 0.054
20S M20 10.0 6.1 11.7 24.0 26.6 21.0 20SA21RA5/A PVC04 0.054
20 M20 10.0 6.5 14.0 27.0 30.0 24.0 20A21RA5/A PVC05 0.059
25 M25 10.0 11.1 20.0 36.0 39.9 26.0 25A21RA5/A PVC09 0.112
SFC 3001 Issue 2 : 06/12

32 M32 10.0 17.0 26.3 41.0 45.5 27.0 32A21RA5/A PVC10 0.128
40 M40 15.0 23.5 32.2 50.0 55.4 28.0 40A21RA5/A PVC13 0.168
50S M50 15.0 31.0 38.2 55.0 61.0 29.0 50SA21RA5/A PVC14 0.224
50 M50 15.0 35.6 44.1 60.0 66.5 30.0 50A21RA5/A PVC17 0.231
63S M63 15.0 41.5 50.0 70.0 77.6 30.0 63SA21RA5/A PVC20 0.360
63 M63 15.0 47.2 56.0 75.0 83.2 30.0 63A21RA5/A PVC22 0.344
75S M75 15.0 54.0 62.0 80.0 88.7 32.0 75SA21RA5/A PVC24 0.466
75 M75 15.0 61.1 68.0 85.0 94.2 32.0 75A21RA5/A PVC26 0.395
90 M90 24.0 66.6 79.4 108.0 120.7 44.0 90A21RA5/A PVC31 1.346
100 M100 24.0 76.0 91.0 123.0 137.8 48.0 100A21RA5/A PVC32 1.575
115 M115 24.0 86.0 98.0 133.4 147.6 55.0 115A21RA5/A LSF34 2.322
130 M130 24.0 97.0 115.0 152.4 164.9 62.0 130A21RA5/A LSF35 3.400
All dimensions in millimetres
Note: *LSF Shrouds also available on request. Marine approvals including Lloyds, DNV & ABS are also available from CMP Products. Other thread forms available on request.

3 www.cmp-products.com.au
 CABLE GLAND AND CABLE CONNECTION SPECIALISTS CMP

CWD CABLE GLAND CWD Industrial Cable Gland

CWD INDUSTRIAL CABLE GLANDS FOR ARMOURED CABLES

CMP CWD Type Nickel Plated Brass indoor and outdoor cable gland for use with all types of Single Wire
Armour (SWA) cable, providing environmental seal on the cable outer sheath. The cable gland also provides
mechanical cable retention and electrical continuity via armour wire termination. A detachable armour cone and
AnyWay universal clamping ring arrangement allows the cable to be easily disconnected from the equipment,
for maintenance and change out etc. This feature also facilitates remote make off procedures when the
termination is to be conducted in confined spaces or in areas of restricted access.
The CMP CWD range of industrial cable glands is designed and tested to BS 6121:Part 1:1989, meets or
surpasses the requirements of EN 50262 :1999 and IEC 62444 : 2010, and is produced from Brass grade
CuZn39Pb3 (CW614N) to EN12168 equal to alloy 385 to AS/NZS 1567 with Electroless Nickel Plating as
standard. All metallic cable gland components are manufactured from the same grade of material. Brass
locknuts are produced in the same grade as the cable gland.

Deluge Proof
TECHNICAL DATA C Seal
A
Type CWD

Design Specification BS 6121:Part 1:1989, EN 50262:1999, IEC 62444 : 2010

Mechanical Classifications Impact = Level 8, Retention = Class B (EN 50262), Class D (IEC 62444)

E
Electrical Classifications Category B

Continuous Operating Temperature -60°C to +150°C

Ingress Protection Rating IP66, IP67, IP68

Standard Cable Gland Material Electroless Nickel Plated Brass

F
Alternative Cable Gland Material Stainless Steel, Aluminium

Seal Material CMP Formulated Thermoplastic Elastomer

Cable Type Single Wire Armour (SWA)

Armour Clamping Detachable Armour Cone & AnyWay Universal Clamping Ring

Sealing Technique Unique CMP "LRS" ™ Outer Seal (Load Retention Seal)
B
Sealing Area(s) Cable Outer Sheath
D

Optional Accessories Adaptor/Reducer, Earth Tag, Serrated Washer, Shroud

Note: Entry Thread Sealing
Washer and Heavy Duty Locknut
included as standard
Cable Gland Selection Table
Standard Cable Overall Across Across
Minimum Nominal Cable
Cable Metric Bedding Cable Armour Range † Flats Corners Ordering
Thread Protrusion Shroud Gland
Gland Entry Diameter ‘A’ Diameter ‘B’ ‘D’ ‘D’ Reference
Length Length Reference* Weight
Size Thread
‘E’ ‘F’ (Kgs)
‘C’ Max Min Max Min Max Max Max
20S/16 M20 20.0 8.7 6.1 11.5 0.8 1.0 24.0 26.6 43.0 20S16CWD1RA5/A PVC04 0.118
20S M20 20.0 11.7 9.5 15.9 0.8 1.25 24.0 26.6 43.0 20SCWD1RA5/A PVC04 0.118
20 M20 20.0 14.0 12.5 20.9 0.8 1.25 30.5 33.3 50.0 20CWD1RA5/A PVC06 0.159
25S M25 20.0 19.9 14.0 22.0 1.25 1.6 36.0 40.0 55.0 25SCWD1RA5/A PVC09 0.228
25 M25 20.0 20.0 18.2 26.2 1.25 1.6 36.0 40.0 55.0 25CWD1RA5/A PVC09 0.228
SFC 3001 Issue 2 : 06/12

32 M32 20.0 26.3 23.7 33.9 1.6 2.0 46.0 51.0 55.0 32CWD1RA5/A PVC11 0.362
40 M40 20.0 32.2 27.9 40.4 1.6 2.0 55.0 61.0 55.0 40CWD1RA5/A PVC15 0.520
50S M50 20.0 38.2 35.2 46.7 2.0 2.5 60.0 66.5 56.0 50SCWD1RA5/A PVC18 0.579
50 M50 20.0 44.1 40.4 53.1 2.0 2.5 70.1 78.6 70.0 50CWD1RA5/A PVC21 0.601
63S M63 20.0 50.0 45.6 59.4 2.0 2.5 75.0 83.2 70.0 63SCWD1RA5/A PVC23 1.054
63 M63 20.0 56.0 54.6 65.9 2.0 2.5 80.0 89.0 80.0 63CWD1RA5/A PVC25 1.200
75S M75 20.0 62.0 59.0 72.1 2.0 2.5 90.0 101.6 81.0 75SCWD1RA5/A PVC28 1.779
75 M75 20.0 68.0 66.7 78.5 2.0 2.5 100.0 111.1 96.0 75CWD1RA5/A PVC30 2.370
90 M90 24.0 80.0 76.2 90.4 3.15 3.15 114.0 128.6 120.0 90CWD1RA5/A PVC32 3.515
100 M100 24.0 91.0 89.1 101.5 3.15 4.0 123.0 136.0 140.0 100CWD1RA5/A LSF33 4.100
115 M115 24.0 98.0 101.3 110.3 3.15 4.0 133.4 147.8 160.0 115CWD1RA5/A LSF34 4.600
130 M130 24.0 115.0 114.0 123.3 3.15 4.0 146.1 152.4 169.0 130CWD1RA5/A LSF35 5.200
All dimensions in millimetres
Note: *LSF Shrouds also available on request. † Alternative armour clamping range available for non-standard armour sizes.

www.cmp-products.com.au 4
 CMP CABLE GLAND AND CABLE CONNECTION SPECIALISTS

Type TMC Heavy Duty Industrial Cable Gland for Variable Speed Drive (VSD)
TMC CABLE GLAND
TMC INDUSTRIAL CABLE GLANDS FOR VARIABLE SPEED DRIVE (VSD) CABLES

cables with Copper Tape Screens or cables with similar metallic sheath
CMP Type TMC Cable Gland suitable for use with screened, metal tape armour or metal clad cables in heavy duty
industrial and wet locations. This is ideally suited for Variable Speed Drive (VSD) with Copper Tape Screen. The cable
gland provides electrical continuity via the metallic screen termination and an environmental seal on the cable outer
sheath. The re-usable compression spring clamp feature provides 360 degree grounding to the cable screen, and
allows the cable to be easily disconnected from the equipment, for maintenance and change out etc if required. The
TMC cable gland offers IP66 and Nema 4X ingress protection and is supplied in Electroless Nickel Plated Brass as
standard. The TMC cable gland is available in Metric (standard) and NPT thread forms.

Features and Benefits: CMP renowned displacement seal provides IP66 and NEMA 4X levels of ingress protection.
• Additional integral Deluge Proof seal for extra protection in extremely harsh offshore and onshore environments •
Independent sealing and screen termination • True 360º grounding • Compact slim profile • Wide cable acceptance
range • Re-usable design • Fewer sizes required to handle more cable variations

TECHNICAL DATA C

Type TMC A
Design Specification BS 6121:Part 1:1989, EN 50262, IEC 62444, UL 514B

Mechanical Classifications Impact = Level 8, Retention = Class B (EN 50262), Class D (IEC 62444)

Electrical Classifications Category B

Continuous Operating Temp. -60˚C to +130˚C

E
Ingress Protection Rating IP66

NEMA Rating NEMA 4X

Lloyds Approval Number 01/00172

DNV Approval Number E-10496 F

ABS Approval Number 01-LD234401A/2-PDA

Cable Gland Material Electroless Nickel Plated Brass, Stainless Steel, or Copper Free Aluminium (<0.4%)

Seal Material CMP SOLO LSF Thermoplastic Elastomer

Screened, Tape Armour and Metal Clad cables, including Variable Speed Drive Cables
Cable Type
(VSD) with Copper Tape Screen

Screen/Armour Termination Earth Continuity in Contact with Metallic Screen via Spring Clamp

Sealing Technique CMP Unique Displacement Seal Concept

B
Sealing Area(s) Cable Outer Sheath

Accessories Adaptor/Reducer, Earth Tag, Locknut, Serrated Washer, Entry Thread Seal, Shroud D

Cable Gland Selection Table

Minimum Copper Tape Screen Overall Cable

Cable Metric Nominal Envelope Diameter ‘D’
Thread Diameter ‘A’ Diameter ‘B’ Shroud
Gland Entry Assembly Ordering Reference
Length Reference*
Size Thread ’C’ Length ‘F’
‘E’
Min Max Min Max Across Flats Across Corners
TMC 050S M20 15.0 8.7 12.8 9.0 14.0 55.9 30.0 33.3 CMPTMC050SNB1AA5 PVC06
TMC 050 M20 15.0 9.1 17.0 13.0 20.0 55.9 36.1 39.9 CMPTMC050NB1AA5 PVC09
SFC 3001 Issue 2 : 06/12

TMC 075 M25 15.0 15.0 23.3 17.0 26.3 55.9 40.9 45.5 CMPTMC075NB1AA5 PVC10
TMC 100 M32 15.0 19.7 29.2 23.1 32.2 56.9 49.8 55.4 CMPTMC100NB1AA5 PVC13
TMC 125 M40 15.0 27.5 35.2 29.5 38.2 56.9 54.9 61.0 CMPTMC125NB1AA5 PVC16
TMC 150 M50 15.0 33.5 41.1 35.6 44.1 60.2 59.9 66.5 CMPTMC150NB1AA5 PVC18
TMC 200S M50 15.0 38.3 47.1 40.1 51.0 65.5 70.6 77.7 CMPTMC200SNB1AA5 PVC21
TMC 200 M63 15.0 45.0 53.0 47.2 56.0 63.2 75.2 83.3 CMPTMC200NB1AA5 PVC24
TMC 250S M63 15.0 52.1 58.9 52.8 62.0 63.5 79.8 88.6 CMPTMC250SNB1AA5 PVC25
TMC 250 M75 15.0 57.1 64.6 59.1 68.0 64.0 85.1 94.2 CMPTMC250NB1AA5 PVC27
TMC 300 M75 15.0 64.6 75.3 66.6 79.4 90.7 110.0 121.9 CMPTMC300NB1AA5 PVC32
TMC 350 M90 24.0 74.0 88.5 76.0 97.3 117.1 133.4 147.8 CMPTMC350NB1AA5 LSF34
TMC 400 M100 24.0 88.9 102.1 94.0 107.2 194.6 134.1 148.3 CMPTMC400NB1AA5 LSF34
All dimensions are in millimetres
Note: Other thread forms available on request, please contact CMP Products for further information.
5 www.cmp-products.com.au
 CABLE GLAND AND CABLE CONNECTION SPECIALISTS CMP

Type A2F Tri-Star Flameproof Ex d, Increased Safety Ex e and

A2F CABLE GLAND Restricted Breathing Ex nR Cable Gland

A2F EXPLOSIVE ATMOSPHERE CABLE GLANDS FOR UNARMOURED CABLES

CMP Type A2F Tri-Star Nickel Plated Brass Triple Certified Flameproof (Type 'd'), Increased Safety (Type
'e') and Restricted Breathing (Type ‘nR’) indoor and outdoor cable gland for use in Zone 1, Zone 2, Zone
21 and Zone 22 explosive atmospheres with un-armoured and braided cable providing a combined
flameproof seal and environmental seal on the cable outer sheath. This product provides full
compatibility with restricted breathing equipment.

The CMP A2F Tri-Star Cable Gland is suitable for use with all forms of equipment protection
permitted in Zone 1, Zone 2, Zone 21 & Zone 22 provided always that the prevailing code of practice for
selection and installation is observed, e.g. IEC 60079-14, AS/NZS 60079.14, or AS/NZS 2381.1, AS/NZS
2381.2, AS 2381.6.

TECHNICAL DATA
C
Type A2F
Design Specification BS 6121: Part 1: 1989, EN 50262:1999, IEC 62444 : 2010 A

ATEX Certificate SIRA06ATEX1097X

ATEX II 2/3 GD Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66, - Equipment Zone 1, Zone
Code of Protection
2, Zone 21, & Zone 22 - Gas Groups IIA, IIB, IIC, ATEX IM2, Ex d I, Ex e I

EN 60079-0:2004, EN 60079-1:2004, EN 60079-7:2003, EN 60079-15:2003,

Compliance Standards
EN 61241-0:2004 EN 61241-1:2004 E

IECEx Certificate IECEx SIR 06.0039X

Code of Protection Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66, Ex d I, Ex e I

IEC 60079-0:2004, IEC 60079-1:2003, IEC 60079-7:2001, IEC 60079-15:2005,

Compliance Standards
IEC 61241-0:2004, IEC 61241-1:2004
F
Lloyds Approval Number 01/00172
DNV Approval Number E-8119
ABS Approval Number 01-LD 234401A/1-PDA
Continuous Operating Temperature -60° to +130°
Ingress Protection Rating IP66, IP67, IP68
Deluge Protection Compliance DTS01 : 91
Cable Gland Material Electroless Nickel Plated Brass (Standard), Stainless Steel, Aluminium

Seal Material CMP SOLO LSF Halogen Free Thermoplastic Elastomer. D

Cable Type Unarmoured & Braided
Sealing Technique CMP Displacement Seal
Sealing Area(s) Cable Outer Sheath
Optional Accessories Adaptor/Reducer, Locknut, Earth Tag, Entry Thread Seal, Serrated Washer, Shroud

Note: These products comply with the corresponding AS/NZS 60079 standards which are identical to the IEC 60079 compliance standards
detailed above.

Cable Gland Selection Table

Minimum Across Across Cable
Cable Standard Metric Overall Cable Nominal Ordering
Thread Diameter ‘A’ Flats ‘D’ Corners ‘D’ Shroud Gland
Gland Entry Threads Protrusion Reference
Length Reference* Weight
Size ‘C’ ‘E’ Length ‘F’
Min Max Max Max (Kgs)
20S/16 M20 15.0 3.2 8.7 24.0 26.6 21.0 20S16A2F1RA5 PVC04 0.054
20S M20 15.0 6.1 11.7 24.0 26.6 21.0 20SA2F1RA5 PVC04 0.054
20 M20 15.0 6.5 14.0 27.0 31.0 24.0 20A2F1RA5 PVC05 0.059
25 M25 15.0 11.1 20.0 36.0 39.0 26.0 25A2F1RA5 PVC09 0.112
SFC 3001 Issue 2 : 06/12

32 M32 15.0 17.0 26.3 41.0 45.0 27.0 32A2F1RA5 PVC10 0.128
40 M40 15.0 23.5 32.2 50.0 53.5 28.0 40A2F1RA5 PVC13 0.168
50S M50 15.0 31.0 38.2 55.0 61.0 29.0 50SA2F1RA5 PVC14 0.224
50 M50 15.0 35.6 44.1 60.0 66.0 30.0 50A2F1RA5 PVC17 0.231
63S M63 15.0 41.5 50.0 70.0 77.5 30.0 63SA2F1RA5 PVC20 0.360
63 M63 15.0 47.2 56.0 75.0 84.0 30.0 63A2F1RA5 PVC22 0.344
75S M75 15.0 54.0 62.0 79.0 87.0 32.0 75SA2F1RA5 PVC24 0.466
75 M75 15.0 61.1 68.0 84.0 94.0 32.0 75A2F1RA5 PVC26 0.395
90 M90 24.0 66.6 80.0 108.0 120.0 44.0 90A2F1RA5 PVC31 1.346
100 M100 24.0 76.0 91.0 122.0 138.0 48.0 100A2F1RA5 PVC32 1.575
115 M115 24.0 86.0 98.0 138.0 148.0 55.0 115A2F1RA5 LSF34 2.322
130 M130 24.0 97.0 115.0 154.0 178.0 62.0 130A2F1RA5 LSF35 3.400
All dimensions in millimetres
Note: *LSF Shrouds also available on request. Marine approvals including Lloyds, DNV & ABS are also available from CMP Products. Other thread forms available on request.

www.cmp-products.com.au 6
 CMP CABLE GLAND AND CABLE CONNECTION SPECIALISTS

E1FW Tri-Star Flameproof Ex d, Increased Safety Ex e and

E1FW CABLE GLAND Restricted Breathing Ex nR Cable Gland
E1FW EXPLOSIVE ATMOSPHERES CABLE GLANDS FOR ARMOURED CABLES

CMP Type E1FW Tri-Star Nickel Plated Brass Triple Certified Flameproof (Type ‘d’), Increased Safety (Type ‘e’) and
Restricted Breathing (Type ‘nR’) cable gland for use in Zone 1, Zone 2, Zone 21 and Zone 22 explosive atmospheres
with Single Wire Armour (SWA) cable. This cable gland provides a Flameproof seal on the cable inner bedding and
in addition the gas tight seal has been tested to prove compatibility with Restricted Breathing equipment. The cable
gland allows mechanical cable retention and earth continuity via the cable armour termination. Separate tightening
actions for the inner displacement seal and the armour termination afford maximum control over the pressure
applied to the cable bedding, and also allows the effectiveness of the gas tight seal to be tested. A detachable
armour cone and AnyWay clamping ring arrangement facilitates remote make off and enables the cable to be
disconnected from the equipment. An environmental / load retention seal is provided on the cable outer sheath.

The CMP E1FW Tri-Star Cable Gland is suitable for use with all forms of equipment protection permitted in Zone 1,
Zone 2, Zone 21 & Zone 22 provided always that the prevailing code of practice for selection and installation is
observed, e.g. IEC 60079-14, AS/NZS 60079.14, or AS/NZS 2381.1, AS/NZS 2381.2, AS 2381.6.

TECHNICAL DATA
C
Type E1FW Tri-Star
A
Design Specification BS 6121: Part 1: 1989, EN 50262:1999, IEC 62444 : 2010

ATEX Certificate SIRA06ATEX1097X

ATEX II 2GD / 3GD Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66, - Equipment Zone
Code of Protection 1, Zone 2, Zone 21, & Zone 22 - Gas Groups IIA, IIB, IIC,
E
ATEX IM2 Exd I / Exe I
EN 60079-0:2004, EN 60079-1:2004, EN 60079-7: 2003, EN 60079-15:2003,
Compliance Standards
EN 61241-0:2004, EN 61241-1:2004

IECEx Certificate IECEx SIR 06.0043X

Code of Protection Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66, Ex d I, Ex e I

IEC 60079-0:2004, IEC 60079-1:2003, IEC 60079-7:2001, IEC 60079-15:2005, F

Compliance Standards
IEC 61241-0:2004, IEC 61241-1:2004
Continuous Operating Temperature -60°C to +130°C

Ingress Protection Rating IP66 as standard, IP67 / IP68 available on request.

Cable Gland Material Electroless Nickel Plated Brass (Standard), Stainless Steel, Aluminium

Seal Material CMP SOLO LSF Halogen Free Thermoplastic Elastomer

Cable Type Single Wire Armour (SWA)

Armour Clamping Detachable Armour Cone & AnyWay Universal Clamping Ring B
CMP Inner Displacement Seal & Unique CMP "LRS"™ Outer Seal (Load Retention
Sealing Technique
Seal) D
Sealing Area(s) Cable Inner Bedding & Cable Outer Sheath

Adaptor/Reducer, Locknut, Earth Tag, Entry Thread Sealing Washer, Serrated

Optional Accessories
Washer, Shroud.
Note: These products comply with the corresponding AS/NZS 60079 standards which are identical to the IEC 60079 compliance standards
detailed above.

Cable Gland Selection Table

Minimum Cable Overall Cable Across Across Nominal Cable
Cable Standard Metric Bedding Diameter Armour Range † Flats Corners Ordering
Thread Protrusion Shroud Gland
Gland Entry Threads Diameter ‘A’ ‘B’ ‘D’ ‘D’ Reference
Length Length Reference* Weight
Size ‘C’
‘E’ ’F’ (Kgs)
Min Max Min Max Min Max Max Max
20S/16 M20 15.0 3.1 8.7 6.1 11.5 0.8 1.0 24.0 24.4 58.5 20S16E1FW1RA5 PVC04 0.157
20S M20 15.0 6.1 11.7 9.5 15.9 0.8 1.25 24.0 26.6 58.5 20SE1FW1RA5 PVC04 0.157
20 M20 15.0 6.5 14.0 12.5 20.9 0.8 1.25 30.5 33.3 60.5 20E1FW1RA5 PVC06 0.206
25S M25 15.0 11.1 20.0 14.0 22.0 1.25 1.6 37.5 40.5 67.5 25SE1FW1RA5 PVC09 0.325
25 M25 15.0 11.1 20.0 18.2 26.2 1.25 1.6 37.5 40.5 67.5 25E1FW1RA5 PVC09 0.325
SFC 3001 Issue 2 : 06/12

32 M32 15.0 17.0 26.3 23.7 33.9 1.6 2.0 46.0 51.0 69.5 32E1FW1RA5 PVC11 0.452
40 M40 15.0 22.0 32.2 27.9 40.4 1.6 2.0 55.0 61.0 78.0 40E1FW1RA5 PVC15 0.657
50S M50 15.0 29.5 38.2 35.2 46.7 2.0 2.5 60.0 66.5 75.5 50SE1FW1RA5 PVC18 0.734
50 M50 15.0 35.6 44.1 40.4 53.1 2.0 2.5 70.0 78.6 80.5 50E1FW1RA5 PVC21 0.748
63S M63 15.0 40.1 50.0 45.6 59.4 2.0 2.5 75.0 83.2 91.5 63SE1FW1RA5 PVC23 1.337
63 M63 15.0 47.2 56.0 54.6 65.9 2.0 2.5 80.0 89.0 92.0 63E1FW1RA5 PVC25 1.436
75S M75 15.0 52.8 62.0 59.0 72.1 2.0 2.5 89.0 101.6 99.0 75SE1FW1RA5 PVC28 2.073
75 M75 15.0 59.1 68.0 66.7 78.5 2.0 2.5 99.0 111.1 102.0 75E1FW1RA5 PVC30 2.622
90 M90 24.0 66.6 80.0 76.2 90.4 3.15 3.15 114.0 128.6 120.0 90E1FW1RA5 PVC32 4.174
100 M100 24.0 76.0 91.0 86.1 101.5 3.15 4.0 123.0 138.0 148.0 100E1FW1RA5 LSF33 4.523
115 M115 24.0 86.0 98.0 101.5 110.3 3.15 4.0 133.4 147.8 169.0 115E1FW1RA5 LSF34 6.860
130 M130 24.0 97.0 115.0 114.2 123.3 3.15 4.0 146.1 161.9 183.0 130E1FW1RA5 LSF35 8.121
All dimensions in millimetres
Note: *LSF Shrouds also available on request. Alternative armour clamping range available for non-standard armour sizes. Marine approvals including Lloyds, DNV & ABS are also available from CMP Products.
Other thread forms available on request. Alternative Type E1FX cable gland with Grooved Cone (X) may be used for other types of approved armoured cables as well as smaller gauge SWA armour wires.
7
www.cmp-products.com.au
 CABLE GLAND AND CABLE CONNECTION SPECIALISTS CMP

Triton CDS (T3CDS) Flameproof Ex d, Increased Safety Ex e and

T3CDS CABLE GLAND Restricted Breathing Ex nR Cable Gland

T3CDS EXPLOSIVE ATMOSPHERES & DELUGE PROOF CABLE GLANDS FOR ARMOURED CABLES
CMP Triton CDS Type T3CDS Nickel Plated Brass Triple Certified Flameproof (Type 'd'), Increased Safety (Type 'e') and Restricted
Breathing (Type ‘nR’) indoor and outdoor cable gland for use in Zone 1, Zone 2, Zone 21 and Zone 22 explosive atmospheres with all
types of armoured cable providing a Flameproof seal on the cable inner bedding and an environmental seal on the cable outer
sheath. This product utilises a unique Compensating Displacement Seal (CDS) system which provides full compatibility with
Restricted Breathing equipment. The cable gland provides mechanical cable retention and electrical continuity via armour wire
termination. A reversible armour cone and AnyWay universal clamping ring arrangement allows the cable to be easily disconnected
from the equipment, for maintenance and change out etc., and re-connected with the same consummate ease. This feature also
facilitates remote make off procedures when the termination is to be conducted in confined spaces or in areas of restricted access.
Separate tightening actions for the inner Compensating Displacement Seal (CDS) system and the armour termination affords
maximum control over the pressure applied to the cable inner bedding. The CMP Triton CDS Cable Gland is suitable for use with all
forms of equipment protection permitted in Zone 1, Zone 2 , Zone 21 & Zone 22 provided always that the prevailing code of practice
for selection and installation is observed, e.g. IEC 60079-14, AS/NZS 60079.14, or AS/NZS 2381.1, AS/NZS 2381.2, AS 2381.6.

TECHNICAL DATA

Type T3CDS

Design Specification BS 6121:Part 1:1989, EN 50262:1999, IEC 62444 : 2010, UL 514B

ATEX Certificate SIRA06ATEX1283X

ATEX II 2/3 GD Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66, Equipment Zone 1, Zone
Code of Protection
2, Zone 21, & Zone 22 - Gas Groups IIA, IIB, IIC

EN 60079-0:2006, EN 60079-1:2004, EN 60079-7:2003, EN 60079-15:2005,

Compliance Standards
EN 61241-0:2004, EN 61241-1:2004

IECEx Certificate IECEx SIR 07.005X

Code of Protection Ex d IIC / Ex e II / Ex nR II / Ex tD A21 IP66

IEC 60079-0:2004, IEC 60079-1:2003, IEC 60079-7:2006, IEC 60079-15:2005,

Compliance Standards
IEC 61241-0:2004, IEC 61241-1:2004

Lloyds Approval Number 01/00172

DNV Approval Number E-6157
ABS Approval Number 01-LD 234401-PDA

Continuous Operating Temperature -60°C to +130°C

Ingress Protection Rating IP66, IP67, IP68

Deluge Protection Compliance DTS01 : 91
Deluge Protection Document ITS 01005029 - D
Cable Gland Material Electroless Nickel Plated Brass (Standard), Stainless Steel, Aluminium
Seal Material CMP SOLO LSF Halogen Free Thermoplastic Elastomer

Single Wire Armour (SWA), Aluminium Wire Armour (AWA), Pliable Wire Armour (PWA),
Cable Type
Steel Tape Armour (STA), Wire Braid, Aluminium Strip Armour (ASA)

Armour Clamping Reversible Armour Cone & AnyWay Universal Clamping Ring
Sealing Technique CMP Inner CDS System & Unique CMP "LRS" ™ Outer Seal (Load Retention Seal)
Sealing Area(s) Cable Inner Bedding & Cable Outer Sheath

Optional Accessories Adaptor/Reducer, Locknut, Earth Tag, Entry Thread Seal, Serrated Washer

Note: These products comply with the corresponding AS/NZS 60079 standards which are identical to the IEC 60079 compliance standards Note: Stepped Cone (W) is suitable for SWA cables,
detailed above. Grooved Cone (X) is suitable for all other approved
armoured cables
Cable Gland Selection Table
Standard Cable Overall Armour Range † Across Across
Bedding Cable Flats Corners Cable
Cable Matric Minimum Nominal
Diameter ‘A’ Diameter ‘B’ Grooved Cone (X) Stepped Cone (W) ‘D’ ‘D’ Ordering Gland
Gland Entry Thread Protrusion
Length ‘E’ Reference Weight
Size Thread Length ‘F’
Min Max Min Max Min Max Min Max Max Max (Kgs)
‘C’
20S/16 M20 15.0 3.1 8.7 6.1 11.5 0.15 1.0 0.8 1.0 24.0 26.6 70.0 20S16T3CDS1RA5 0.170
20S M20 15.0 6.1 11.7 9.5 15.9 0.15 1.0 0.8 1.25 24.0 26.6 70.0 20ST3CDS1RA5 0.170
20 M20 15.0 6.5 14.0 12.5 20.9 0.15 1.0 0.8 1.25 30.5 33.3 72.0 20T3CDS1RA5 0.256
25S M25 15.0 11.1 20.0 14.0 22.0 0.15 1.0 1.25 1.6 37.5 40.5 82.0 25ST3CDS1RA5 0.384
SFC 3001 Issue 2 : 06/12

25 M25 15.0 11.1 20.0 18.2 26.2 0.15 1.0 1.25 1.6 37.5 40.5 82.0 25T3CDS1RA5 0.379
32 M32 15.0 17.0 26.3 23.7 33.9 0.15 1.0 1.6 2.0 46.0 51.0 85.0 32T3CDS1RA5 0.560
40 M40 15.0 22.0 32.2 27.9 40.4 0.15 1.0 1.6 2.0 55.0 61.0 86.0 40T3CDS1RA5 0.848
50S M50 15.0 29.5 38.2 35.2 46.7 0.15 1.0 2.0 2.5 60.0 66.5 98.0 50ST3CDS1RA5 1.055
50 M50 15.0 35.6 44.1 40.4 53.1 0.15 1.0 2.0 2.5 70.0 78.6 100.0 50T3CDS1RA5 1.521
63S M63 15.0 40.1 50.0 45.6 59.4 0.15 1.0 2.0 2.5 75.0 83.2 108.0 63ST3CDS1RA5 1.750
63 M63 15.0 47.2 56.0 54.6 65.9 0.15 1.0 2.0 2.5 80.0 89.0 103.0 63T3CDS1RA5 1.685
75S M75 15.0 52.8 62.0 59.0 72.1 0.15 1.0 2.0 2.5 89.0 101.6 105.0 75ST3CDS1RA5 2.345
75 M75 15.0 59.1 68.0 66.7 78.5 0.15 1.0 2.0 2.5 99.0 111.1 114.0 75T3CDS1RA5 3.200
90 M90 24.0 66.6 80.0 76.2 90.4 0.25 1.6 3.15 3.15 114.0 128.6 140.0 90T3CDS1RA5 5.100
100 M100 24.0 80.0 91.0 86.1 101.5 0.25 1.6 3.15 4.0 123.0 138.0 170.0 100T3CDS1RA5 6.500
115 M115 24.0 90.0 98.0 101.5 110.3 0.25 1.6 3.15 4.0 133.4 147.6 210.0 115T3CDS1RA5 7.000
130 M130 24.0 100.0 115.0 114.2 123.3 0.25 1.6 3.15 4.0 146.1 161.9 250.0 130T3CDS1RA5 7.800
All dimensions in millimetres
Note: †Alternative armour clamping range available for non-standard armour sizes. Marine approvals including Lloyds, DNV & ABS are also available from CMP Products. Other thread forms available on request.

www.cmp-products.com.au 8
 CMP CABLE GLAND AND CABLE CONNECTION SPECIALISTS

PXSS2K Flameproof Ex d, Increased Safety Ex e, Restricted

PXSS2K CABLE GLAND
Breathing Ex nR Compound Barrier Cable Gland
PXSS2K EXPLOSIVE ATMOSPHERES COMPOUND BARRIER CABLE GLANDS FOR UNARMOURED CABLES

CMP Type PXSS2K Nickel Plated Brass Triple Certified Flameproof (Type ‘d’), Increased Safety (Type ‘e’) and
Restricted Breathing (Type ‘nR’) cable gland for use in Zone 1, Zone 2, Zone 21 and Zone 22 explosive
atmospheres with all types of unarmoured cable providing a compound barrier seal around the cable
conductors and an environmental seal on the cable outer sheath. The cable gland provides mechanical cable
retention. A combined detachable spacer and compound tube allows the cable to be easily disconnected from
the equipment, for maintenance and change out etc., and re-connected with the same consummate ease. This
feature also facilitates remote make off procedures when the termination is to be conducted in confined spaces
or in areas of restricted access.
The CMP PXSS2K cable gland is suitable for use with all forms of equipment protection permitted in Zone 1,
Zone 2, Zone 21 & Zone 22 provided always that the prevailing code of practice for selection and installation is
observed, e.g. IEC 60079-14, AS/NZS 60079.14, or AS/NZS 2381.1, AS/NZS 2381.2, AS 2381.6.

TECHNICAL DATA
C
Type PXSS2K
A
BS 6121:Part 1:1989, EN 50262:1999, IEC 62444 : 2010, UL 514B, UL 886,
Design Specification
UL 2225, UL 2227
ATEX Certificate SIRA06ATEX1097X
ATEX I I 2 GD Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66 - Equipment Zone 1,
Code of Protection
Zone 2, Zone 21, & Zone 22 - Gas Groups IIA, IIB, IIC, ATEX IM2, Exd I / Exe I
EN 60079-0: 2004, EN 60079-1: 2004, EN 60079-7: 2003, EN 60079-15: 2003,
Compliance Standards
EN 61241-0: 2004 EN 61241-1: 2004 E
IECEx Certificate IECEx SIR 06.0044X
Code of Protection Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66, Ex d I, Ex e I
IEC 60079-0:2004, IEC 60079-1:2003, IEC 60079-7:2001, IEC 60079-15:2005,
Compliance Standards
IEC 61241-0:2004, IEC 61241-1:2004
Lloyds approval Number 01/00172
DNV Approval Number E-6157
F
ABS Approval Number 01-LD 234401-PDA
Continuous Operating Temperature -60°C to +100°C
Ingress Protection Rating IP66, IP67, IP68
Ingress Protection Document 5046 C549J
Deluge Protection Compliance DTS01 : 91
Deluge Protection Document 5046 C549J-D
NEMA Rating NEMA 4X
Cable Gland Material Electroless Nickelplated Brass (Standard), Stainless Steel, Aluminium
B
Seal Material CMP SOLO LSF Halogen Free Thermoplastic Elastomer / Barrier Compound
D
Cable Type Unarmoured
Sealing Technique CMP Displacement Seal
Sealing Area(s) Inner Compound Barrier # & Cable Outer Sheath
Optional Accessories Adaptor/Reducer, Locknut, Earth Tag, Entry Thread Seal, Serrated Washer, Shroud

Note : These products comply with the corresponding AS/NZS 60079 standards which are identical to the IEC 60079 compliance standards
detailed above.

Cable Gland Selection Table

Diameter Overall Cable Across Across
Number Nominal Cable
Cable Standard Metric Minimum Over Corners
of Diameter Flats Protrusion Ordering Shroud Gland
Gland Entry Threads Thread Conductors Conductors ‘B’ ‘D’ ‘D’ Length Reference Reference* Weight
Length ‘E’ ‘A’
Size ‘C’
Max Max Min Max Max Max ‘F’ (Kgs)

20S/16 M20 15.0 12.6 15 3.0 8.7 24.0 26.6 58.5 20S16PXSS2K1RA5 PVC04 0.200
20S M20 15.0 12.6 15 6.1 11.7 24.0 26.6 58.5 20SPXSS2K1RA5 PVC04 0.200
SFC 3001 Issue 2 : 06/12

20 M20 15.0 12.6 15 6.5 14.0 30.5 33.3 60.5 20PXSS2K1RA5 PVC04 0.250
25 M25 15.0 17.5 29 11.1 20.0 37.5 40.5 67.5 25PXSS2K1RA5 PVC09 0.403
32 M32 15.0 23.6 51 17.0 26.3 46.0 51.0 69.5 32PXSS2K1RA5 PVC09 0.555
40 M40 15.0 30.0 80 22.0 32.1 55.0 61.0 78.0 40PXSS2K1RA5 PVC15 0.600
50S M50 15.0 36.6 122 29.5 38.2 60.0 66.5 75.5 50SPXSS2K1RA5 PVC18 0.605
50 M50 15.0 41.0 149 35.6 44.1 70.0 78.6 80.5 50PXSS2K1RA5 PVC21 0.620
63S M63 15.0 47.9 205 40.1 50.1 75.0 83.2 91.5 63SPXSS2K1RA5 PVC23 0.705
63 M63 15.0 53.7 259 47.2 56.0 80.0 89.0 92.0 63PXSS2K1RA5 PVC25 0.730
75S M75 15.0 59.8 320 52.8 62.0 89.0 101.6 99.0 75SPXSS2K1RA5 PVC28 1.150
75 M75 15.0 64.3 364 59.1 68.0 99.0 111.1 102.0 75PXSS2K1RA5 PVC30 1.300
90 M90 24.0 75.3 500 66.6 79.4 114.0 128.6 120.0 90PXSS2K1RA5 PVC32 2.700
All dimensions in millimetres
Note: *LSF Shrouds also available on request. Marine approvals including Lloyds, DNV & ABS are also available from CMP Products. Other thread forms available on request. #Alternative CMP RapidEx Liquid Pour
Resin version available on request. Type number is followed by REX in the ordering reference, e.g 20PXSS2KREX1RA5
www.cmp-products.com.au
9
 CABLE GLAND AND CABLE CONNECTION SPECIALISTS CMP

PX2KW Flameproof Ex d, Increased Safety Ex e, Restricted

PX2KW CABLE GLAND
Breathing Ex nR Compound Barrier Cable Gland

PX2KW EXPLOSIVE ATMOSPHERES COMPOUND BARRIER CABLE GLANDS FOR ARMOURED CABLES
CMP Type PX2KW Nickel Plated Brass Triple Certified Flameproof (Type ‘d’), Increased Safety (Type ‘e’) and
Restricted Breathing (Type ‘nR’) cable gland for use in Zone 1, Zone 2, Zone 21 and Zone 22 explosive
atmospheres with all types of armoured cable providing a compound barrier seal around the cable conductors
and an environmental seal on the cable outer sheath. The cable gland provides mechanical cable retention and
electrical continuity via armour termination.
A combined detachable armour cone and compound tube, together with AnyWay universal clamping ring
arrangement allows the cable to be easily disconnected from the equipment, for maintenance and change out etc,
and re-connected with the same consummate ease. This feature also facilitates remote make off procedures when
the termination is to be conducted in confined spaces or in areas of restricted access.
The CMP PX2K cable gland is suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2,
Zone 21 & Zone 22 provided always that the prevailing code of practice for selection and installation is observed,
e.g. IEC 60079-14, AS/NZS 60079.14, or AS/NZS 2381.1, AS/NZS 2381.2, AS 2381.6.

C
TECHNICAL DATA
Type PX2KW A

Design Specification BS 6121:Part 1:1989, EN 50262:1999, IEC 62444 : 2010

ATEX Certificate SIRA06ATEX1097X
ATEX II 2 GD Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66 - Equipment
Code of Protection
Zone 1, Zone 2, Zone 21, & Zone 22 - Gas Groups IIA, IIB, IIC
EN 60079-0:2004, EN 60079-1:2004, EN 60079-7:2003, EN 60079-15:2003,
Compliance Standards
EN 61241-0:2004, EN 61241-1:2004 E
IECEx Certificate IECEx SIR 06.0044X
Code of Protection Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66
IEC 60079-0:2004, IEC 60079-1:2003, IEC 60079-7:2001,
Compliance Standards
IEC 60079-15:2005, IEC 61241-0:2004, IEC 61241-1:2004
F
Lloyds Approval Number 01/00172
DNV Approval Number E-6157
ABS Approval Number 01-LD 234401-PDA
Continuous Operating Temperature -60°C to +100°C
Ingress Protection Rating IP66, IP67, IP68
Ingress Protection Document 5046 C549G
Deluge Protection Compliance DTS01 : 91
Deluge Protection Document 5046 C549G-D B

Cable Gland Material Electroless Nickel Plated Brass (Standard), Stainless Steel, Aluminium
D
Seal Material CMP SOLO LSF Halogen Free Thermoplastic Elastomer / Barrier Compound
PX2KW = Single Wire Armour (SWA)
Cable Type
PX2KX = Wire Braid, Steel Tape Armour (STA) Pliable Wire Armour (PWA) & SWA
Armour Clamping Detachable Compound Tube / Cone & AnyWay Universal Clamping Ring
Sealing Technique Unique CMP "LRS" ™ Outer Seal (Load Retention Seal) Note: Dedicated version for Steel Wire Armour type is PX2KW.
Dedicated version for all other Armour types is PX2KX
Sealing Area(s) Inner Compound Barrier # & Cable Outer Sheath Note: This standard design concept is also available with
Adaptor/Reducer, Locknut, Earth Tag, Entry Thread Sealing Washer, Serrated bi-code approvals, suitable for installation in systems
Optional Accessories complying with NEC wiring code rules.
Washer, Shroud.
Note : These products comply with the corresponding AS/NZS 60079 standards which are identical to the IEC 60079 compliance standards
detailed above.

Cable Gland Selection Table

Diameter Number Overall Armour Range † Across Across Nominal
Over Cable Cable
Cable Standard Metric Minimum of Flats Corners Protrusion
Grooved Stepped Ordering Shroud Gland
Gland Entry Threads Thread Conductors Conductors Diameter
Cone (X) Cone (W) ‘D’ ‘D’
Length ‘E’ ‘A’ ‘B’ Length Reference Reference* Weight
Size ‘C’
Max Max Min Max Min Max Min Max Max Max ‘F’ (Kgs)
20S/16 M20 15.0 12.6 15 6.1 11.5 0.0 1.0 0.8 1.25 24.0 26.6 58.5 20S16PX2KW1RA5 PVC04 0.200
20S M20 15.0 12.6 15 9.5 15.9 0.0 1.0 0.8 1.25 24.0 26.6 58.5 20SPX2KW1RA5 PVC04 0.200
20 M20 15.0 12.6 15 12.5 20.9 0.0 1.0 0.8 1.25 30.5 33.3 60.5 20PX2KW1RA5 PVC06 0.230
SFC 3001 Issue 2 : 06/12

25S M25 15.0 17.5 29 14.0 22.0 0.0 1.0 1.25 1.6 37.5 40.5 67.5 25SPX2KW1RA5 PVC09 0.330
25 M25 15.0 17.5 29 18.2 26.2 0.0 1.0 1.25 1.6 37.5 40.5 67.5 25PX2KW1RA5 PVC09 0.330
32 M32 15.0 23.6 51 23.7 33.9 0.0 1.0 1.6 2.0 46.0 51.0 69.5 32PX2KW1RA5 PVC11 0.510
40 M40 15.0 30.0 80 27.9 40.4 0.0 1.0 1.6 2.0 55.0 61.0 78.0 40PX2KW1RA5 PVC15 0.720
50S M50 15.0 36.6 122 35.2 46.7 0.0 1.0 2.0 2.5 60.0 66.5 75.5 50SPX2KW1RA5 PVC18 0.825
50 M50 15.0 41.0 149 40.4 53.1 0.0 1.0 2.0 2.5 70.0 78.6 80.5 50PX2KW1RA5 PVC21 0.860
63S M63 15.0 47.9 205 45.6 59.4 0.0 1.0 2.0 2.5 75.0 83.2 91.5 63SPX2KW1RA5 PVC23 1.450
63 M63 15.0 53.7 259 54.6 65.9 0.0 1.0 2.0 2.5 80.0 89.0 92.0 63PX2KW1RA5 PVC25 1.600
75S M75 15.0 59.8 320 59.0 72.1 0.0 1.0 2.0 2.5 89.0 101.6 99.0 75SPX2KW1RA5 PVC28 2.300
75 M75 15.0 64.3 364 66.7 78.5 0.0 1.0 2.0 2.5 99.0 111.1 102.0 75PX2KW1RA5 PVC30 3.050
90 M90 24.0 75.3 500 76.2 90.4 0.0 1.6 3.15 3.15 114.0 128.6 120.0 90PX2KW1RA5 PVC32 5.000
All dimensions in millimetres
Note: *LSF Shrouds also available on request. †Alternative armour clamping range available for non-standard armour sizes. Marine approvals including Lloyds, DNV & ABS are also available from CMP Products.
Other thread forms available on request. When SWA cable is not being used please substitute the ‘W’ with ‘X’ in the ordering reference, e.g. 20PX2KX1RA5. #Alternative CMP RapidEx Liquid Pour Resin
version available on request. Type number is followed by REX in the ordering reference, e.g 20PX2KWREX1RA5

www.cmp-products.com.au 10
 CMP CABLE GLAND AND CABLE CONNECTION SPECIALISTS

ACCESSORIES
ACCESSORIES

LOCKNUTS SERRATED WASHERS EARTH TAGS

Nickel Plated Brass Locknuts are the recommended Available in Stainless Steel as standard, CMP Nickel Plated Brass Earth Tags, Installed
items used in securing nickel plated brass cable these “shake-proof” Serrated Washers between the cable gland and equipment, provide
glands, unions, adaptors, reducers, and stopper fitted internally to the equipment and an earth bond connection as specified in
plugs to a gland plate or into equipment. Aluminium before a locknut act as an anti-vibration BS6121:Part 5:1993 and also complies with
locknuts are recommended when installing CMP device to prevent the cable gland or category ‘B’ rating specified in BS EN 50262:1999.
Aluminium Cable Glands to prevent the electrolytic other cable entry device and locknut The following table of fault current ratings relates
action of galvanic corrosion which can occur when arrangement from inadvertently to CMP slip on Earth Tags.
dis-similar metals are coupled together. loosening in service.

LOCKNUTS SERRATED WASHERS EARTH TAGS

Thread Ordering Size Hole Nominal
Ordering Across Across Ordering
Diameter Reference Reference Reference Size Centres
Reference Flats Corners Reference
‘A’
16ET5 M16 M6 30.2
16LN5 M16 X 1.5 22.0 25.4 16SW4 M16 20ET5 M20 M6 33.1
20LN5 M20 X 1.5 24.0 28.6 20SW4 M20 25ET5 M25 M6 35.6
25LN5 M25 X 1.5 30.0 35.0 25SW4 M25 32ET5 M32 M12 43.1
32SW4 M32 40ET5 M40 M13 45.4
32LN5 M32 X 1.5 36.0 42.0
50ET5 M50 M13 58.1
40LN5 M40 X 1.5 46.0 53.0 40SW4 M40
63ET5 M63 M13 66.8
50LN5 M50 X 1.5 55.0 64.0 50SW4 M50 75ET5 M75 M13 73.0
63LN5 M63 X 1.5 70.0 81.0 63SW4 M63 90ET5 M90 M13 85.0
75LN5 M75 X 1.5 80.0 98.0 75SW4 M75 100ET5 M100 M13 118.0

90LN5 M90 X 2 108.0 125.0 90SW4 M90

100LN5 M100 X 2 122.0 141.5 100SW4 M100
CMP Short Circuit Ratings
Earth Tag Symmetrical Fault Current
Size (kA) for 1 second
20 3.06
ENTRY THREAD SEALING WASHERS 25 4.00
32 5.40
To maintain the Ingress Protection rating between the equipment and cable gland it may be necessary to 40 7.20
fit an Entry Thread Sealing Washer at the gland entry interface. For Explosion Protected equipment it is 50 10.40
essential to maintain the integrity of the degree of Ingress Protection at which the equipment has been 63 10.40
rated.
75 10.40
The need for a sealing washer will very much depend on the Ingress Protection rating and code of
protection of the equipment and the type of entry holes available within that equipment.

The CMP Entry Thread Sealing Washers are produced in 2mm ENTRY THREAD SEALING WASHERS
Thick White Nylon as standard which are recommended and Ordering Reference Size Reference
meet the specified requirements of Shell’s Offshore operations. 16ETS2 M16
20ETS2 M20
To verify the effectiveness of the CMP nylon entry sealing
25ETS2 M25
washers independent 3rd party tests to EN 60529 have been
32ETS2 M32
successfully conducted on Cable Gland at IP66, IP67 & IP68
levels of protection. 40ETS2 M40
50ETS2 M50
CMP can therefore provide Independent documentary evidence 63ETS2 M63
of such tests to the highest standards. 75ETS2 M75
90ETS2 M90
100ETS2 M100
SFC 3001 Issue 2 : 06/12

SHROUDS CMP manufacture a range of push on shrouds which are used to minimise the risk of dirt or foreign substances gathering on
the Cable Gland body, and/or point of cable to gland interface. Standard shrouds are produced in Black or Orange PVC.
CMP LSF (Blue/Grey) shrouds are available from stock. Table below shows typical examples of CMP shrouds.

COLOUR CODED SHROUDS - Shrouds are also manufactured in alternative colours including Red, Blue and White, to suit a
wide variety of customer requirements, other colours are available.

SHROUD REFERENCES
GLAND TYPE 20S/16 20S 20 25 32 40 50S 50 63S 63 75S 75 90 100 115 130
A2 PVC04 PVC04 PVC05 PVC09 PVC10 PVC13 PVC14 PVC17 PVC20 PVC22 PVC24 PVC26 PVC31 PVC32 LSF34 LSF35
CWD PVC04 PVC04 PVC06 PVC09 PVC11 PVC15 PVC18 PVC21 PVC23 PVC25 PVC28 PVC30 PVC32 LSF33 LSF34 LSF35

11 www.cmp-products.com.au
 CABLE GLAND AND CABLE CONNECTION SPECIALISTS CMP

Stopper Plugs, Adaptors, Reducers, Breather/Drain Plugs

CMP ADAPTORS, REDUCERS, STOPPER PLUGS, BREATHER/DRAIN PLUGS

747, 757 & 767 787
STOPPER PLUGS RIGHT ANGLED
ADAPTOR

TECHNICAL DATA
TECHNICAL DATA
COMPONENT APPROVED RIGHT ANGLED ADAPTOR DESIGNED TO
COMPONENT APPROVED STOPPER PLUGS DESIGNED TO
PROTECT CABLES WHEN INSTALLED IN CONFINED SPACES WHERE
CLOSE UNUSED CABLE ENTRY HOLES IN EXPLOSION
THE CABLE MAY OTHERWISE BE SUBJECT TO EXCESSIVE BENDING
PROTECTED EQUIPMENT. VERSIONS AVAILABLE WITH &
STRESS, AND OFFERS A MEANS OF CONNECTION WHERE THE
WITHOUT INTEGRAL ‘O’ RING SEAL, AND FOR INDUSTRIAL
CABLE CANNOT BE INSTALLED IN THE USUAL PERPENDICULAR
OR SAFE AREA USE.
FASHION. VERSIONS AVAILABLE WITH HAZARDOUS AREA
APPROVAL DETAIL CERTIFICATION AND ALSO FOR INDUSTRIAL OR SAFE AREA USE.
ATEX APPROVAL : SIRA 01ATEX1284U
IECEx APPROVAL : SIRA IEC Ex SIR07.0056X
APPROVAL DETAIL
COMPLIANCE : EN / IEC 60079-0, EN / IEC 60079-1, ATEX APPROVAL : SIRA 01ATEX1284U
IECEx APPROVAL : IEC Ex SIR07.0055U
EN / IEC 60079-7, EN 50281 / IEC 61241-0 & IEC 61241-1
COMPLIANCE : EN / IEC 60079-0, EN / IEC 60079-1,
HAZARDOUS AREA CODE OF PROTECTION :
EN / IEC 60079-7, EN 50281 / IEC 61241-0 & IEC 61241-1
II 2 GD Ex d IIC / Ex e II COMPONENT ZONE 1, ZONE 2,
ZONE 21, & ZONE 22 - GAS GROUPS IIA, IIB, IIC, Ex tD HAZARDOUS AREA CODE OF PROTECTION :
IEC Ex : Ex d I / Ex e I / Ex d IIC / Ex e II / Ex tD A21 IP6X II 2 GD Ex d IIC / Ex e II COMPONENT ZONE 1, ZONE 2,
ZONE 21, & ZONE 22 - GAS GROUPS IIA, IIB, IIC, Ex tD
ADDITIONAL APPROVALS HELD IEC Ex : Ex d I / Ex e I / Ex d IIC / Ex e II / Ex tD A21 IP6X
ABS, DNV & LLOYDS
ADDITIONAL APPROVALS HELD
ABS, DNV & LLOYDS

Thread Ordering Reference

Size 747 Recessed (Type A *) 757 Hex head 767 Round Head
M16 747DAM15 757DM15 767DM15
Thread Size Ordering Reference
M20 747DAM25 757DM25 767DM25 M20 x M20 787DM2M25
M25 747DAM35 757DM31 767DM35 M25 x M25 787DM3M35
M32 747DAM45 757DM45 767DM45 M32 x M32 787DM4M45
M40 747DAM55 757DM55 767DM55 M40 x M40 787DM5M55
M50 747DAM65 757DM65 767DM65 1/2” NPT x M20 787DT1M25
M63 747DAM75 757DM75 767DM75 3/4” NPT x M25 787DT2M35
M75 747DAM85 757DM85 767DM85 1/2” NPT x 1/2” NPT 787DT1T15
Note*: Type A non tamper proof stopper plugs are externally secured by allen key 3/4” NPT x 3/4” NPT 787DT2T25

737 781D & 781E

ADAPTORS AND BREATHER
REDUCERS DRAIN PLUG

TECHNICAL DATA TECHNICAL DATA

COMPONENT APPROVED BREATHER DRAIN PLUG FOR USE WITH
COMPONENT APPROVED ADAPTORS & REDUCERS
FLAMEPROOF Ex d OR INCREASED SAFETY Ex e ENCLOSURES THAT ARE
DESIGNED TO CONVERT THREAD FORMS AND SIZES
SUSCEPTIBLE TO CONDENSATION OR PRONE TO MOISTURE
BETWEEN EXPLOSION PROTECTED EQUIPMENT AND
COLLECTION OR INGRESS DURING NORMAL OPERATION.
CABLE ENTRY DEVICES. VERSIONS AVAILABLE WITH &
WITHOUT INTEGRAL ‘O’ RING SEAL, AND ALSO FOR VERSIONS AVAILABLE IN BRASS, ALUMINIUM, STAINLESS STEEL,
INDUSTRIAL OR SAFE AREA USE. OR NON-METALLIC.

APPROVAL DETAIL APPROVAL DETAIL

ATEX APPROVAL : SIRA 01ATEX1284U ATEX APPROVAL : SIRA 10ATEX1307U
IECEx APPROVAL : IEC Ex SIR07.0052X IECEx APPROVAL : IEC Ex SIR 10.0149U
COMPLIANCE : EN / IEC 60079-0, EN / IEC 60079-1, COMPLIANCE : EN / IEC 60079-0, EN / IEC 60079-1, EN / IEC 60079-7, EN /
EN / IEC 60079-7, EN 50281 / IEC 61241-0 & IEC 61241-1 IEC 60079-31
HAZARDOUS AREA CODE OF PROTECTION : HAZARDOUS AREA CODE OF PROTECTION :
II 2 GD Ex d IIC / Ex e II COMPONENT ZONE 1, ZONE 2, II 2 GD Ex d IIC Gb or Ex e IIC / Ex ta IIIC Da, COMPONENT ZONE 1,
ZONE 21, & ZONE 22 - GAS GROUPS IIA, IIB, IIC, Ex tD ZONE 2, ZONE 21, & ZONE 22 - GAS GROUPS IIA, IIB, IIC
IEC Ex : Ex d I / Ex e I / Ex d IIC / Ex e II / Ex tD A21 IP6X IEC Ex : Ex d IIC Gb & Ex ta IIIC Da (Type 781D)
SFC 3001 Issue 2 : 06/12

Ex e IIC Gb & Ex ta IIIC Da (Type 781E)

ADDITIONAL APPROVALS HELD INGRESS PROTECTION : IP66
ABS, DNV & LLOYDS
ADDITIONAL APPROVALS HELD
Virtually any thread conversion imaginable can be supplied. ABS, DNV & LLOYDS
Please see page 13 for common sizes and how to order.

Ordering Reference
Size Flameproof Type d Increased Safety Type e
Nickel Plated Brass Stainless Steel Nickel Plated Brass Stainless Steel
M20 781DM25 781DM24 781EM25 781EM24
Note : These products comply with the corresponding AS/NZS 60079 standards M25 781DM35 781DM34 781EM35 781EM34
which are identical to the IEC 60079 compliance standards detailed above.

www.cmp-products.com.au 12
 CMP CABLE GLAND AND CABLE CONNECTION SPECIALISTS

CMP 737 THREAD CONVERSION ADAPTOR & REDUCER - STANDARD SIZE SELECTION TABLE
CMP 737 THREAD CONVERSION ADAPTOR & REDUCER - STANDARD SIZE SELECTION TABLE

MALE THREAD FEMALE THREAD

P1A
M1
M2
M3
M4
M5
M6
M7
M8

P1
P2
P3
P4
P5
P6
P7
P8
P9

B1
B2
B3
B4
B5
B6
B7
B8
T1
T2
T3
T4
T5
T6
T7
T8
ORDERING CODE
DEFINITION (**)

1 1/4” BSPP
1 1/2” BSPP

2 1/2” BSPP
SIZE

1 1/4” NPT
1 1/2” NPT

1/2” BSPP
3/4” BSPP
2 1/2”NPT
1/2” NPT
3/4” NPT

1” BSPP

2” BSPP

3” BSPP
PG13.5

1” NPT

2” NPT

3” NPT
PG11

PG16
PG21
PG29
PG36
PG42
PG48
M16
M20
M25
M32
M40
M50
M63
M75
PG7
PG9
M16 M1
M20 M2
M25 M3
M32 M4
M40 M5
M50 M6
M63 M7
M75 M8
PG7 P1A
PG9 P1
PG11 P2
PG13.5 P3
PG16 P4
PG21 P5
PG29 P6
PG36 P7
PG42 P8
PG48 P9
1/2” NPT T1
3/4” NPT T2
1” NPT T3
1 1/4” NPT T4
1 1/2” NPT T5
2” NPT T6
2 1/2” NPT T7
3 NPT T8
1/2” BSPP B1
3/4” BSPP B2
1” BSPP B3
1 1/4” BSPP B4
1 1/2” BSPP B5
2” BSPP B6
2 1/2” BSPP B7
3” BSPP B8
SFC 3001 Issue 2 : 06/12

KEY:
How to Compile Ordering Codes
IEC Ex CERTIFIED REDUCER
Type - Protection - Male Size(**) - Female Size(**) - Material

Examples : IEC Ex CERTIFIED ADAPTOR

737-D-M2-M3-5 = M20 x M25 Adaptor, Nickel Plated Brass
INDUSTRIAL ADAPTOR / REDUCER
737-D-B2-M3-4 = ¾” BSPP x M25 Adaptor, Stainless Steel
Letter D following Type 737 = Dual Certified Ex d / Ex e.
737-D-M3-M2-4 = M25 x M20 Adaptor, Stainless Steel Suffix 5 = Nickel Plated Brass. Suffix 4 = Stainless Steel.

13 www.cmp-products.com.au
 CABLE GLAND AND CABLE CONNECTION SPECIALISTS CMP

CMP CABLE GLAND SELECTION TABLES BASED UPON AS/NZS 5000.1 & 5000.2 CABLES

CMP CABLE GLAND SELECTION TABLES

450/750V & 0.6/1.kV PVC/PVC Power Cables 0.6/1.kV PVC/PVC/SWA/PVC Power Cables
Conductor Size mm2 2C + E 3C + E 4C + E Conductor Size mm2 2C + E 3C + E 4C + E

1.5 20SA2 20SA2 20SA2 1.5 20SCWD 20SCWD 20CWD

2.5 20SA2 20SA2 20A2 2.5 20SCWD 20CWD 20CWD
4 20SA2 20A2 20A2 4 20CWD 20CWD 20CWD
6 20A2 20A2 25A2 6 20CWD 20CWD 25SCWD
10 25A2 25A2 25A2 10 25SCWD 25CWD 25CWD
16 25A2 25A2 32A2 16 25CWD 25CWD 32CWD
25 32A2 32A2 32A2 25 25CWD 32CWD 32CWD
35 32A2 32A2 40A2 35 32CWD 32CWD 32CWD
50 32A2 40A2 40A2 50 32CWD 40CWD 40CWD
70 - 40A2 50SA2 70 - 40CWD 50SCWD
95 - 50SA2 50A2 95 - 50SCWD 50CWD
120 - 50A2 63SA2 120 - 50CWD 63SCWD
150 - 63SA2 63A2 150 - 63SCWD 63CWD
185 - 63A2 75SA2 185 - 63CWD 75SCWD
240 - 75SA2 75A2 240 - 75SCWD 75CWD
300 - 75A2 90A2 300 - 75CWD 90CWD

0.6/1.kV PVC/PVC Control Cables 0.6/1.kV PVC/SWA/PVC Control Cables

Conductor Size Conductor Size
Number of Conductors Number of Conductors
2 2 2
1.5 mm 2.5 mm 1.5 mm 2.5 mm2
5C + E 20A2 25A2 5C + E 20CWD 20CWD
6C + E 20A2 25A2 6C + E 20CWD 20CWD
8C + E 25A2 25A2 8C + E 20CWD 25CWD
10C + E 25A2 25A2 10C + E 25SCWD 25CWD
12C + E 25A2 25A2 12C + E 25SCWD 25CWD
15C + E 25A2 32A2 15C + E 25CWD 25CWD
16C + E 25A2 32A2 16C + E 25CWD 32CWD
20C + E 32A2 32A2 20C + E 25CWD 32CWD
25C + E 32A2 32A2 25C + E 32CWD 32CWD
30C + E 32A2 40A2 30C + E 32CWD 32CWD
36C + E 32A2 40A2 36C + E 32CWD 40CWD
40C + E 40A2 40A2 40C + E 32CWD 40CWD
50C + E 40A2 50SA2 50C + E 40CWD 50SCWD

PVC/PVC Instrument Cables PVC/PVC/SWA/PVC Instrument Cables

Collectively Screened Individually & Collectively Screened Collectively Screened Individually & Collectively Screened
Number of Number of
Pairs/Triples Pairs/Triples
0.5 mm2 1.5 mm2 0.5 mm2 1.5 mm2 0.5 mm2 1.5 mm2 0.5 mm2 1.5 mm2
2PR 20S/16A2 20SA2 20S/16A2 20SA2 2PR 20S/16CWD 20SCWD 20SCWD 20SCWD
4PR 20S/16A2 20A2 20SA2 25A2 4PR 20SCWD 20CWD 20SCWD 25SCWD
6PR 20SA2 25A2 20A2 25A2 6PR 20SCWD 25SCWD 20CWD 25CWD
8PR 20SA2 25A2 20A2 25A2 8PR 20SCWD 25CWD 20CWD 25CWD
10PR 20A2 25A2 25A2 32A2 10PR 20CWD 25CWD 20CWD 32CWD
12PR 20A2 32A2 25A2 32A2 12PR 20CWD 32CWD 25CWD 32CWD
16PR 25A2 32A2 25A2 40A2 16PR 25SCWD 32CWD 32CWD 40CWD
20PR 25A2 32A2 32A2 40A2 20PR 25CWD 32CWD 32CWD 40CWD
24PR 25A2 40A2 32A2 50SA2 24PR 32CWD 40CWD 32CWD 50SCWD
SFC 3001 Issue 2 : 06/12

36PR 32A2 50SA2 32A2 50A2 36PR 32CWD 50SCWD 40CWD 50CWD
50PR 32A2 50A2 40A2 63A2 50PR 32CWD 50CWD 50CWD 63CWD
4TR 20SA2 20A2 20A2 25A2 4TR 20SCWD 25SCWD 20CWD 25CWD
6TR 20A2 25A2 25A2 32A2 6TR 20CWD 32CWD 25SCWD 32CWD
8TR 20A2 25A2 25A2 32A2 8TR 25SCWD 32CWD 25SCWD 32CWD
10TR 20A2 25A2 25A2 32A2 10TR 25SCWD 32CWD 25CWD 40CWD
12TR 25A2 32A2 32A2 40A2 12TR 25CWD 40CWD 25CWD 50SCWD
16TR 32A2 40A2 40A2 50SA2 16TR 32CWD 40CWD 32CWD 50SCWD
24TR 32A2 40A2 50SA2 50A2 24TR 32CWD 50SCWD 40CWD 63SCWD
36TR 50SA2 50A2 50A2 63A2 36TR 40CWD 63CWD 50SCWD 63CWD

These cable gland selection charts are provided for guidance purposes. Users are advised to check their actual cable dimensions before
ordering cable glands.
www.cmp-products.com.au 14
 www.cmp-products.com www.cmp-products.com.cn www.cmp-products.ru

NEWCASTLE (Headquarters) DUBAI PERTH, WA

CMP Products (British Engines (Middle East) FZE) CMP Products
36, Nelson Way, Nelson Park East CMP Products Middle East Office Units 2-3 / 22 Harlond Avenue
Cramlington, Northumberland P.O. Box 61363, Jebel Ali Free Zone Malaga, WA 6090
NE23 1WH, United Kingdom Jebel Ali, Dubai, United Arab Emirates Australia
Tel: +44 191 265 7411 Tel: +971 4 887 1012 +61 8 9249 4508
Fax: +44 167 071 5646 Fax: +971 4 887 1015 +61 8 9249 4608
E-Mail: cmp@cmp-products.com E-Mail: meoffice@cmp-products.com E-Mail: perthoffice@cmp-products.com
CALL 1300 GLANDS (1300 452 637)

HOUSTON PUSAN
(British Engines Texas Inc) CMP Products (Korea) Ltd
CMP Products 19F Rm1915 Centum IS Tower, #1209,
5222 N. Sam Houston Parkway E. Jaesong1-dong, Haeundae-gu,
Houston, Texas, 77032, USA Busan, South Korea, 612051
Tel: +1 281 776 5201 Tel: +82 51 780 5300
Fax: +1 281 776 5223 Fax: +82 51 780 8348
E-Mail: pusanoffice@cmp-products.com
E-Mail: houstonoffice@cmp-products.com

SINGAPORE SHANGHAI
CMP Products (S.E.A) Pte Ltd. (BEL Industrial Products (Shanghai) Co., Ltd)
21 Toh Guan Road East, #09-03, CMP Products
Toh Guan Centre Room 304, Building 7, No.1888 Xin Jinqiao Road
Singapore 608609 Pudong District, Shanghai 201206, P.R. China
Tel: +65 6466 6180 Tel: +86 21 6093 2633
Fax: +65 6466 9891 Fax: +86 21 6093 2630
E-Mail: seaoffice@cmp-products.com E-Mail: shanghaioffice@cmp-products.com

A comprehensive technical product catalogue

Available from: TPC 188 covering the full CMP product range
is available on request. For any other
requirement not listed within this short form
catalogue, please feel free to convey your
application to the nearest office detailed above,
as CMP prides itself in having the ability and
flexibility to provide solutions that meet the very
needs of industry. Whether your application is for
General Purpose Industrial, Ordinary Locations,
Marine and Wet Locations, or Hazardous
Locations, CMP delivers the solution at the right
place, the right time and the right price.

FOR FURTHER INFORMATION:

CALL 1300 GLANDS (1300 452 637)

PRINTED IN AUSTRALIA

CMP

www.cmp-products.com.au
SFC 3001 Issue 2 : 06/12