TASK CARD AIRCRAFT ID

CC-BCD
T00W2DHM Page: 1 /2

TASK NAME ETOPS

281100-01-2-LH-SVC(JIC) (DRAIN WATER CONTENT)

TASK INFORMATION
OEM Part Number Serial Nº Effective Code Task Priority

A319-112 4871 251 MANDAT

Organization W/P Line Nº Work Location Work Order W/P Barcode

DGAC Chile CMA N°E-596 AVIO 19 LIM/LINE WO - 205851308 T00W2WBU

Parent Inventory Inventory

A319-112 - CC-BCD 12-32-00 - SAMPLING FOR ANALYSIS

Panels Zones
196BB - Yellow hydraulic bay. (Access to the same 190 - BELLY FAIRING, AIR CONDITIONING AND
components as through 196 AB) HYDRAULKICS COMPARTMENT
195BB - Blue hydraulic bay. (Access to the same 500 - Left Wing
components as through 195 AB)

DESCRIPTION
(LH WING) TANKS

DRAIN WATER CONTENT

NOTE:
INTERVAL:
- DEPENDING ON OPERATING ENVIRONMENT AND OPERATORS
EXPERIENCE, A LESS FREQUENT OR MORE FREQUENT
INITIAL INTERVAL MAY BE USED.

Form TC-001 Rev. 03

 281100-01-2-LH-SVC(JIC) - DRAIN WATER
CONTENT [T00W2DHM] CC-BCD
Page: 2 /2

Enginnering Instructions
AMM TASK 12-32-28-281-001-A AMM REV. 49,01 May 2025

Action Taken

1. herman german izquierdo suarez, 03- PERFORMED LH DRAIN WATER CONTENT IAW AMM TASK 12-32-28-281-001-A. REV 49
SEP-2025 07:12 SATISFACTORY

PARTS ON/OFF

DESCRIPTION QTY PN OFF SN OFF QTY PN ON SN ON

TOOLS

QTY DESCRIPTION PART NUMBER BATCH N°

1 ADAPTING PIPE - WATER DRAINING 98A28101000000

1 PURGING TOOL 97A28002117002

1 BOTELLA DRENAJE COMBUSTIBLE 98A28104000000

1 BOTTLE PURGING TOOL A-319/320 98A28104000002

SIGNATURE

The signer(s) below certifies that the work has been completed satisfactorily

SKILL Signed by Date - Time(UTC) Signature

Form TC-001 Rev. 03

 TASK STEPS CC-BCD

281100-01-2-LH-SVC(JIC) - DRAIN WATER CONTENT

Page: 1/11
[T00W2DHM]

STEP 1
AMM TASK 12-32-28-281-001-A Accomplished By
Drain Water Content STATUS: Complete
WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING NOTICES ARE IN POSITION BEFORE
YOU START A TASK ON OR NEAR:
herman german
izquierdo suarez
- THE FLIGHT CONTROLS
A320
- THE FLIGHT CONTROL SURFACES

- THE LANDING GEAR AND RELATED DOORS Lic. No.: 6040

- THE CARGO DOORS 03/09/2025 07:12:29
- OTHER COMPONENTS THAT MOVE. (UTC)
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

WARNING: BE CAREFUL NOT TO GET AIRCRAFT FUEL IN YOUR MOUTH OR IN YOUR EYES.

IF YOU GET FUEL ON YOUR SKIN OR ON YOUR CLOTHES, FLUSH IT IMMEDIATELY WITH WATER.

IF NECESSARY, GET MEDICAL HELP.

AIRCRAFT FUEL IS POISONOUS.

Reason for the Job

(Ref. Refer to the MPD TASK: 281100-01)

DRAIN WATER CONTENT

You can do this task together with TASK 12-32-28-281-003-A (Sample Fuel for
Microbiological Contamination Analysis) and TASK 12-32-28-281-802-A (Sample Fuel for
Hydraulic-Oil Contamination Analysis). If you are sampling for microbiological
contamination of fuel do task 12-32-28-281-003-A instead of this task. If you do the
Microbiological/Hydraulic-Oil Contamination Analysis, you must clean the applicable drain
tool and the container as given in the AMM tasks.
NOTE: If possible, Airbus recommends you to do the water drain procedure before the flight or the refuel procedure.
If you do this procedure after the flight or the refuel procedure, you must wait for one hour for the separation of the
water and the fuel.
NOTE: It is permitted to do this procedure when the APU is in operation only if the fuel tank pumps are set to
OFF.

For indirect water drain-valves:

If you have less than 10% content of the fuel, then the indirect water drain-valves will
have a decreased flow.

If you have less than 10% content of the fuel it is recommended that you fill more fuel or
use the suction procedure.

For direct water drain-valves:

Uplift of additional fuel is not required for the operation of direct water drain-valves.

2. Job Set-up Information

A. Fixtures, Tools, Test and Support Equipment

Form TC-001 Rev. 03

 TASK STEPS CC-BCD

281100-01-2-LH-SVC(JIC) - DRAIN WATER CONTENT

Page: 2/11
[T00W2DHM]

REFERENCE QTY DESIGNATION

No specific AR CONTAINER 10 L(2 1/2 USGAL)

No specific 1 CONTAINER-CLEAN, STERILIZED, TRANSPARENT GLASS

No specific 1 CONTAINER-FUEL RESISTANT, TRANSPARENT PLASTIC

No specific AR HYDROKIT

No specific 1 PUMP - SUCTION (ATEX APPROVED)

No specific AR SAFETY BARRIER(S)

No specific AR WARNING NOTICE(S)

97A28002117002 1 TOOL-PURGING

98A28101000000 1 ADAPTING PIPE - WATER DRAINING FROM FUEL

98A28104000000 1 PURGER-WATER DRAIN

98A28104000002 1 TOOL - PURGING

98A28104031001 1 PURGER-WATER DRAIN

98D28104000000 1 PIPE ADAPTING-WATER DRAINING

B. Work Zones and Access Panels

ZONE/ACCESS ZONE DESCRIPTION

LOWER HALF OF FUSELAGE INCLUDING

100
RADOME

BELLY FAIR, AIR CONDITIONING & HYD

190
COMPT

500 LEFT WING

600 RIGHT WING

FOR 94QM (VALVE-WATER DRAIN, L CTR

TK)

195BB

FOR 95QM (VALVE-WATER DRAIN, R CTR

TK)

196BB

C. Referenced Information

Form TC-001 Rev. 03

 TASK STEPS CC-BCD

281100-01-2-LH-SVC(JIC) - DRAIN WATER CONTENT

Page: 3/11
[T00W2DHM]

REFERENCE DESIGNATION

Cold Weather
12-31-28-660-001-A Maintenance -
Fuel

Sample Fuel for

Microbiological
12-32-28-281-003-A
Contamination
Analysis

Deactivation of
the VHF
23-12-00-040-802-A
Antenna for
Maintenance

Reactivation of
the VHF
23-12-00-440-802-A
Antenna After
Maintenance

Fuel Safety
28-00-00-910-001-A
Procedures
** On A/C 001-009 011-050 101-150 154-200 246-300 351-352 356-356 358-372 378-379
381-400 501-501 503-504 506-506 508-508 510-512 517-525 527-527 529-529 531-536
540-550 561-567 571-571 582-600 605-608 610-611 615-709 712-712 717-718 725-725
729-750 901-908 911-951 953-957 960-999
(Ref. Fig 12-32-28-991-00100-00-B - Fuel Sampling For Analysis)
** On A/C ALL
** On A/C 401-425 427-428 430-433 435-450 801-900
(Ref. Fig 12-32-28-991-00100-00-C - Fuel Sampling For Analysis)
** On A/C ALL
** On A/C 001-009 011-050 101-150 154-200 246-300 351-352 356-356 358-372 378-379
381-400 501-501 503-504 506-506 508-508 510-512 517-525 527-527 529-529 531-536
540-550 561-567 571-571 582-600 605-608 610-611 615-709 712-712 717-718 725-725
729-750 901-908 911-951 953-957 960-999
(Ref. Fig 12-32-28-991-00700-00-B - Fuel Sampling For Analysis - Suction Procedure)
** On A/C ALL
** On A/C 401-425 427-428 430-433 435-450 801-900
(Ref. Fig 12-32-28-991-00700-00-C - Fuel Sampling For Analysis - Suction Procedure)

** On A/C ALL

Form TC-001 Rev. 03

 TASK STEPS CC-BCD

281100-01-2-LH-SVC(JIC) - DRAIN WATER CONTENT

Page: 4/11
[T00W2DHM]

STEP 2
Accomplished By
** On A/C ALL
STATUS: Complete
3. Job Set-up
** On A/C 001-009 011-050 101-150 154-200 246-300 351-352 356-356 358-372 378-379 381-400 501-501 503-504 herman german
506-506 508-508 510-512 517-525 527-527 529-529 531-536 540-550 561-567 571-571 582-600 605-608 610-611 izquierdo suarez
615-709 712-712 717-718 725-725 729-750 901-908 911-951 953-957 960-999
A320
(Ref. Fig 12-32-28-991-00100-00-B - Fuel Sampling For Analysis)
** On A/C 401-425 427-428 430-433 435-450 801-900 Lic. No.: 6040
(Ref. Fig 12-32-28-991-00100-00-C - Fuel Sampling For Analysis) 03/09/2025 07:12:29
** On A/C ALL (UTC)
SUBTASK 12-32-28-040-052-A

A. Deactivation of the VHF Antenna

WARNING: BEFORE YOU DO MAINTENANCE WORK WITHIN A RADIUS OF 1 METER (3 FEET) AROUND AND
ABOVE THE VHF ANTENNA, MAKE SURE THAT THE ANTENNA IS DE-ENERGIZED. THE ANTENNA USES
HIGH POWER WHEN IT TRANSMITS AND CAN CAUSE INJURY TO PERSONS.
(1) If necessary, do the deactivation of the VHF antenna for maintenance (Ref. TASK 23-12-00-040-802-A).

STEP 3
Accomplished By
SUBTASK 12-32-28-941-054-B
STATUS: Complete
B. Safety Precautions
herman german
WARNING: OBEY THE FUEL SAFETY PROCEDURES. THIS CAN PREVENT INJURY AND DAMAGE.
izquierdo suarez
(1) You must obey the fuel safety procedures when you do work on the fuel system (Ref. TASK 28-00-00-910-001-
A). A320
(2) As necessary, use the applicable SAFETY BARRIER(S), specified by the operator's Lic. No.: 6040
instructions and your local regulations.
03/09/2025 07:12:29
(3) In the cockpit, on panel 400VU:
(UTC)
Make sure that the landing-gear control-lever 6GA is in the DOWN
position

Put the WARNING NOTICE(S) in position to tell persons not to operate

the landing gear.

(4) Put the WARNING NOTICE(S) in position to tell persons not to operate the landing
gear doors.

(5) If the fuel temperature is less than 0 DEG.C (32.00 DEG.F) and/or the water drain
valves are frozen, to keep the flight turnaround times, one of the two steps that
follow:

Do the cold weather maintenance procedure to warm the water drain

valve (Ref. TASK 12-31-28-660-001-A)

Remove the fuel samples 60 minutes after the refuel procedure.

NOTE: Removal of the fuel samples in less than 60 minutes will not remove the water content as satisfactorily as
samples removed one hour after the refuel procedure.
NOTE: Airbus recommends you that not to apply unusually high force to open the water drain
valve.

Form TC-001 Rev. 03

 TASK STEPS CC-BCD

281100-01-2-LH-SVC(JIC) - DRAIN WATER CONTENT

Page: 5/11
[T00W2DHM]

(6) If the APU is in operation during this procedure, you must make sure that the fuel
tank pumps are set to OFF.

STEP 4 - N/A
Accomplished By
SUBTASK 12-32-28-010-050-B
STATUS: N/A
C. Get Access
herman german
(1) To get access to the center-tank water-drain valves, open the applicable access izquierdo suarez
door:
A320
(a) FOR 94QM (VALVE-WATER DRAIN, L CTR TK)
Lic. No.: 6040
Open access door 195BB.
03/09/2025 07:12:29
(b) FOR 95QM (VALVE-WATER DRAIN, R CTR TK) (UTC)
Open access door 196BB.

STATUS NOTE:

03/09/2025 07:12:29 (UTC): N/A

Form TC-001 Rev. 03

 TASK STEPS CC-BCD

281100-01-2-LH-SVC(JIC) - DRAIN WATER CONTENT

Page: 6/11
[T00W2DHM]

STEP 5
Accomplished By
SUBTASK 12-32-28-480-050-A
STATUS: Complete
D. Preparation of the Equipment
herman german
(1) To get access to the high water drain valves from the ground, attach the: izquierdo suarez
ADAPTING PIPE - WATER DRAINING FROM FUEL A320
(98A28101000000)
or the Lic. No.: 6040
PIPE ADAPTING-WATER DRAINING (98D28104000000) 03/09/2025 07:12:29
to the bottle and funnel of the PURGER-WATER DRAIN (UTC)
(98A28104000000).

STEP 6
Accomplished By
** On A/C 001-009 011-050 101-150 154-200 246-300 351-352 356-356 358-372 378-379 381-400 501-501 503-504
506-506 508-508 510-512 517-525 527-527 529-529 531-536 540-550 561-567 571-571 582-600 605-608 610-611 STATUS: Complete
615-709 712-712 717-718 725-725 729-750 901-908 911-951 953-957 960-999
herman german
(Ref. Fig 12-32-28-991-00100-00-B - Fuel Sampling For Analysis)
izquierdo suarez
(Ref. Fig 12-32-28-991-00700-00-B - Fuel Sampling For Analysis - Suction Procedure)
A320
** On A/C 401-425 427-428 430-433 435-450 801-900
Lic. No.: 6040
(Ref. Fig 12-32-28-991-00100-00-C - Fuel Sampling For Analysis)
03/09/2025 07:12:29
(Ref. Fig 12-32-28-991-00700-00-C - Fuel Sampling For Analysis - Suction Procedure)
(UTC)
** On A/C ALL

STEP 7
Accomplished By
** On A/C ALL
STATUS: Complete
SUBTASK 12-32-28-281-050-B
herman german
A. Fuel Sampling for Water Contamination
izquierdo suarez
(1) Gravity Procedure:
A320
(a) For the gravity procedure, you can use the TOOL-PURGING
(97A28002117002) to drain the fuel from the wing tanks and the centre tank, but Lic. No.: 6040
it does not prevent leaks. 03/09/2025 07:12:29
1 It is recommended to use the TOOL - PURGING (98A28104000002) to drain (UTC)
the fuel from the centre tank and the PURGER-WATER DRAIN
(98A28104000000) to drain the fuel from the wing tanks.

(b) For indirect water drain-valves, make sure that the fuel tanks are filled to a
minimum of 10% of capacity. This is necessary to cover the water drain-valve
outlet, so that the water drain valves can operate satisfactorily.

(c) For the wing-tank water drain-valves:

CAUTION: MAKE SURE THAT THE PLUNGER OF THE TOOL ALIGNS CORRECTLY WITH THE WATER DRAIN
VALVE. INCORRECT ALIGNMENT OF THE TOOL CAN CAUSE:
THE WATER DRAIN VALVE TO STAY IN THE OPEN POSITION AFTER THE TOOL IS REMOVED
A FUEL LEAK.

Form TC-001 Rev. 03

 TASK STEPS CC-BCD

281100-01-2-LH-SVC(JIC) - DRAIN WATER CONTENT

Page: 7/11
[T00W2DHM]

1 Push the center of the applicable water drain valve with the PURGER-WATER
DRAIN (98A28104000000):

a Drain approximately 1.0 l (0.26 USgal) of fuel from the water drain valve.
NOTE: The surge tanks are the temporary tanks that are made to collect fuel that can overflow from the vent lines.
Usually, no fuel can be drained from the surge tanks.

2 Remove the PURGER-WATER DRAIN (98A28104000000) from the water

drain valve.

(d) For the center-tank water drain-valves:

1 Push the center of the applicable water drain valve with the TOOL -
PURGING (98A28104000002):

a Drain approximately 1.0 l (0.26 USgal) of fuel from the water drain valve.

2 Remove the TOOL - PURGING (98A28104000002) from the water drain

valve.

3 Examine the water drain valve for fuel leakage:

a If the water drain valve does leak, use the TOOL - PURGING
(98A28104000002) to push (in) and release (out) the center of the
valve three or four times.

b Make sure that there are no leaks.

c This step is very important at center-tank water-drain-valves 94QM and

95QM, where access is not easy.

(e) Put the fuel sample into the CONTAINER-CLEAN, STERILIZED,

TRANSPARENT GLASS or the CONTAINER-FUEL RESISTANT,
TRANSPARENT PLASTIC.

1 If you do not do the analysis immediately, seal the container.

(f) Do the sample removal procedure at all the water drain valves.

(2) Suction Procedure:

(a) If you use the TOOL-PURGING (97A28002117002), do the steps that follow:

1 You must use an approved type of the PUMP - SUCTION (ATEX

APPROVED) for use on a fuel system:

a You must obey the applicable safety precautions.

2 On the TOOL-PURGING (97A28002117002) fully retract the nut (5), the

screw (4) and the plunger assembly (1).
CAUTION: MAKE SURE THAT THE PLUNGER OF THE TOOL ALIGNS CORRECTLY WITH THE WATER DRAIN
VALVE. INCORRECT ALIGNMENT OF THE TOOL CAN CAUSE:
THE WATER DRAIN VALVE TO STAY IN THE OPEN POSITION AFTER THE TOOL IS REMOVED
A FUEL LEAK.

3 Put the hexagonal end of the bush (2) into the bottom of the water drain valve.

4 Turn the bush (2) through 30 deg (30 deg).

5 Turn the nut (5) until it touches and seals against the bottom skin.

6 Attach the PUMP - SUCTION (ATEX APPROVED) to the hose (3).

Form TC-001 Rev. 03

 TASK STEPS CC-BCD

281100-01-2-LH-SVC(JIC) - DRAIN WATER CONTENT

Page: 8/11
[T00W2DHM]

7 Put the outlet of the PUMP - SUCTION (ATEX APPROVED) to the

CONTAINER 10 L(2 1/2 USGAL).

8 Hold the bush (2) and turn the screw (4) clockwise to its stop:

a This causes the plunger (1) to open the drain valve. Fuel can now flow
into the PUMP - SUCTION (ATEX APPROVED).

9 Start the PUMP - SUCTION (ATEX APPROVED).

10 Continuously monitor the fuel flow into the CONTAINER 10 L(2 1/2 USGAL).

11 Drain approximately 1.0 l (0.26 USgal) of fuel (as a sample) from the drain
valve.
NOTE: The surge tanks are the temporary tanks that are made to collect fuel that can overflow from the vent lines.
Usually, no fuel can be drained from the surge tanks.

12 When you drained sufficient fuel sample, turn the screw (4) counter
clockwise to its stop.

13 Stop the PUMP - SUCTION (ATEX APPROVED).

14 Remove the PUMP - SUCTION (ATEX APPROVED) from the hose (3).

15 Turn the nut (5) until it does not touch the bottom skin.

16 Turn the hexagonal end of the bush (2) to 30 deg (30 deg):

a Remove the TOOL-PURGING (97A28002117002) from the bottom of the

water drain valve.

17 Put the fuel sample into the CONTAINER-CLEAN, STERILIZED,

TRANSPARENT GLASS or the CONTAINER-FUEL RESISTANT,
TRANSPARENT PLASTIC.

a If you do not do the analysis immediately, seal the container.

18 Do this procedure at all the water drain valves.

(b) If you use the PURGER-WATER DRAIN (98A28104031001), do the steps that
follow:
CAUTION: MAKE SURE THAT THE PLUNGER OF THE TOOL ALIGNS CORRECTLY WITH THE WATER DRAIN
VALVE. INCORRECT ALIGNMENT OF THE TOOL CAN CAUSE:
THE WATER DRAIN VALVE TO STAY IN THE OPEN POSITION AFTER THE TOOL IS REMOVED
A FUEL LEAK.

1 Push the center of the applicable water drain valve with the PURGER-WATER
DRAIN (98A28104031001).

2 Operate the PURGER-WATER DRAIN (98A28104031001) and collect

approximately 1 l (0.26 USgal) of fuel (as a sample) from the drain valve.
NOTE: The surge tanks are the temporary tanks that are made to collect fuel that can overflow from the vent lines.
Usually, no fuel can be drained from the surge tanks.

3 Continue to operate the water drain valve until only fuel comes out.

4 Remove the PURGER-WATER DRAIN (98A28104031001) from the water

drain valve.

5 Put the fuel sample into the CONTAINER-CLEAN, STERILIZED,

TRANSPARENT GLASS or the CONTAINER-FUEL RESISTANT,
TRANSPARENT PLASTIC.

Form TC-001 Rev. 03

 TASK STEPS CC-BCD

281100-01-2-LH-SVC(JIC) - DRAIN WATER CONTENT

Page: 9/11
[T00W2DHM]

a If you do not do the analysis immediately, seal the container.

6 Examine the water drain valve for fuel leakage:

a If the water drain valve does leak, use the PURGER-WATER DRAIN
(98A28104031001) to push (in) and release (out) the center of the
valve three or four times.

b Make sure that there are no leaks.

7 Do this procedure at all the water drain valves.

(3) Do a test for the microbiological contamination in less than 10 days, if:

(a) You can see brown slimy, white particles and/or sludge in the sample that you
drain from the tank.
(b) You can see particles in the sample (Ref. TASK 12-32-28-281-003-A).

STEP 8
Accomplished By
SUBTASK 12-32-28-750-050-A
STATUS: Complete
B. Water Contamination Test
herman german
NOTE: This procedure gives the instructions to find the water content in the drained
sample. izquierdo suarez
This procedure is applicable to find out if the drained sample contains A320
water.

(1) Let the sample become stable:

Lic. No.: 6040

(a) If the sample moves into two layers it contains water. Drain the water from the
03/09/2025 07:12:29
water drain valve continuously until it has no water. (UTC)
WARNING: DO THE TEST ONLY IN AN APPROVED AREA. THIS WILL HELP TO PREVENT CONTAMINATION
AND EXPLOSIONS.

(b) If the sample stays in one layer, it can be full of fuel or full of water. To find if the
sample is fuel or water, do the test that follows:

If you test for the microbiological contamination, do not use the HYDROKIT
or put other material in the fuel (if not water).

Form TC-001 Rev. 03

 TASK STEPS CC-BCD

281100-01-2-LH-SVC(JIC) - DRAIN WATER CONTENT

Page: 10/11
[T00W2DHM]

ACTION RESULT
If the powder stays white, then
the sample is fuel and the test is
complete.

or
1.If you have the HYDROKIT available, then put the
contents into the sample. If the white powder changes color
to purple, the sample is water.

Continue to take the samples and

test then until the water drain
valve has no water.
If the sample moves into two
layers, then the sample is full of
fuel and the test is complete.

or
2.If you do not have the HYDROKIT available, then add
water to the sample. If the sample stays in one layer,
then the sample is water.

Continue to take the samples and

test them until the water drain
valve has no water.
NOTE: You can use the same procedure to do an analysis on a
sample from a fuel tanker. You can remove the sample from the
supply connector of the fuel tanker.

STEP 9 - N/A
Accomplished By
5. Close-up STATUS: N/A
SUBTASK 12-32-28-410-050-B
herman german
A. Close Access izquierdo suarez
(1) Make sure that the work area is clean and clear of tools and other items. A320
(2) Close the applicable access door: Lic. No.: 6040
(a) FOR 94QM (VALVE-WATER DRAIN, L CTR TK) 03/09/2025 07:12:29
(UTC)
Close access door 195BB.

(b) FOR 95QM (VALVE-WATER DRAIN, R CTR TK)

Close access door 196BB.

STATUS NOTE:

03/09/2025 07:12:29 (UTC): N/A

Form TC-001 Rev. 03

 TASK STEPS CC-BCD

281100-01-2-LH-SVC(JIC) - DRAIN WATER CONTENT

Page: 11/11
[T00W2DHM]

STEP 10
Accomplished By
SUBTASK 12-32-28-942-050-A
STATUS: Complete
B. Removal of Equipment
herman german
(1) Make sure that the work area is clean and clear of tools and other items. izquierdo suarez
NOTE: To discard the water samples, refer to the local regulations.
A320
(2) Remove the safety barriers.
Lic. No.: 6040
(3) Remove the WARNING NOTICE(S).
03/09/2025 07:12:29
(4) Remove the ground support and maintenance equipment, the special and standard (UTC)
tools and all other items.

STEP 11
Accomplished By
SUBTASK 12-32-28-440-050-A
STATUS: Complete
C. Reactivation of the VHF Antenna
herman german
(1) If deactivated, do the reactivation of the VHF antenna after maintenance (Ref. TASK 23-12-00-440-802-A).
izquierdo suarez
A320
Lic. No.: 6040
03/09/2025 07:12:29
(UTC)

Form TC-001 Rev. 03

 RIB2
25QM
C (26QM)

23QM
(24QM) A
21QM
(22QM)

94QM 95QM
A RIB15
RIB16
RIB22
RIB23

WATER
FUEL TANK
DRAIN VALVE
BOTTOM-SKIN

PLUNGER B

PURGING TOOL
98A28104000000 A
TYPICAL

B 01

NOTE:
0 1 CORRECT ALIGNMENT OF THE PLUNGER WITH THE WATER DRAIN VALVE. N_MM_123228_3_ACM0_01_02

Page 1 of 8
Fuel Sampling For Analysis : Fuel Sampling For Analysis - Sheet 1
On A/C 001-009 011-050 101-150 154-200 246-300 351-352 356-356 358-372 378-379 381-400 501-501 503-504 506-506 508-508 510-512 517-525
527-527 529-529 531-536 540-550 561-567 571-571 582-600 605-608 610-611 615-709 712-712 717-718 725-725 729-750 901-908 911-951 953-957
960-999
 FUEL TANK D
BOTTOM-SKIN

WATER DRAIN VALVE

PLUNGER

C
TYPICAL

PURGING TOOL
98A28104000002

D 01

NOTE:
0 1 CORRECT ALIGNMENT OF THE PLUNGER WITH THE WATER DRAIN VALVE. N_MM_123228_3_ACM0_02_01

Page 2 of 8
Fuel Sampling For Analysis : Fuel Sampling For Analysis - Sheet 2
On A/C 001-009 011-050 101-150 154-200 246-300 351-352 356-356 358-372 378-379 381-400 501-501 503-504 506-506 508-508 510-512 517-525
527-527 529-529 531-536 540-550 561-567 571-571 582-600 605-608 610-611 615-709 712-712 717-718 725-725 729-750 901-908 911-951 953-957
960-999
 RIB2
25QM
C (26QM)

A
21QM
(22QM)

94QM 95QM
A
RIB22
RIB23

WATER
FUEL TANK
DRAIN VALVE
BOTTOM-SKIN

PLUNGER B

PURGING TOOL
98A28104000000 A
TYPICAL

B 01

NOTE:
0 1 CORRECT ALIGNMENT OF THE PLUNGER WITH THE WATER DRAIN VALVE. N_MM_123228_3_SAM0_01_02

Page 3 of 8
Fuel Sampling For Analysis : Fuel Sampling For Analysis - Sheet 1
On A/C 401-425 427-428 430-433 435-450 801-900
 FUEL TANK D
BOTTOM-SKIN

WATER DRAIN VALVE

PLUNGER

C
TYPICAL

PURGING TOOL
98A28104000002

D 01

NOTE:
0 1 CORRECT ALIGNMENT OF THE PLUNGER WITH THE WATER DRAIN VALVE. N_MM_123228_3_SAM0_02_01

Page 4 of 8
Fuel Sampling For Analysis : Fuel Sampling For Analysis - Sheet 2
On A/C 401-425 427-428 430-433 435-450 801-900
 RIB2
25QM
(26QM)
A C
A C
23QM
(24QM)
21QM
(22QM)

94QM 95QM
A C RIB15
RIB16
RIB22 WATER DRAIN VALVE
RIB23

WATER DRAIN VALVE

FUEL TANK PLUNGER
BOTTOM-SKIN

B
1
5

PURGING TOOL
2 97A28002117002
4

3
A
TYPICAL

B 01

NOTE:
0 1 CORRECT ALIGNMENT OF THE PLUNGER WITH THE WATER DRAIN VALVE. N_MM_123228_3_ANM0_01_04

Page 5 of 8
Fuel Sampling For Analysis - Suction Procedure : Fuel Sampling For Analysis - Suction Procedure - Sheet 1
On A/C 001-009 011-050 101-150 154-200 246-300 351-352 356-356 358-372 378-379 381-400 501-501 503-504 506-506 508-508 510-512 517-525
527-527 529-529 531-536 540-550 561-567 571-571 582-600 605-608 610-611 615-709 712-712 717-718 725-725 729-750 901-908 911-951 953-957
960-999
 FUEL TANK
BOTTOM-SKIN

WATER DRAIN WATER

PURGER DRAIN VALVE
98A28104031001

PLUNGER

C
TYPICAL
WATER DRAIN
PURGER

D 01

NOTE:
0 1 CORRECT ALIGNMENT OF THE PLUNGER WITH THE WATER DRAIN VALVE. N_MM_123228_3_ANM0_02_01

Page 6 of 8
Fuel Sampling For Analysis - Suction Procedure : Fuel Sampling For Analysis - Suction Procedure - Sheet 2
On A/C 001-009 011-050 101-150 154-200 246-300 351-352 356-356 358-372 378-379 381-400 501-501 503-504 506-506 508-508 510-512 517-525
527-527 529-529 531-536 540-550 561-567 571-571 582-600 605-608 610-611 615-709 712-712 717-718 725-725 729-750 901-908 911-951 953-957
960-999
 RIB2
25QM
(26QM)
A C
A C

21QM
(22QM)

94QM 95QM
A C
RIB22 WATER DRAIN VALVE
RIB23

WATER DRAIN VALVE

FUEL TANK PLUNGER
BOTTOM-SKIN

B
1
5

PURGING TOOL
2 97A28002117002
4

3
A
TYPICAL

B 01

NOTE:
0 1 CORRECT ALIGNMENT OF THE PLUNGER WITH THE WATER DRAIN VALVE. N_MM_123228_3_AQM0_01_04

Page 7 of 8
Fuel Sampling For Analysis - Suction Procedure : Fuel Sampling For Analysis - Suction Procedure - Sheet 1
On A/C 401-425 427-428 430-433 435-450 801-900
 FUEL TANK
BOTTOM-SKIN

WATER DRAIN WATER

PURGER DRAIN VALVE
98A28104031001

PLUNGER

C
TYPICAL
WATER DRAIN
PURGER

D 01

NOTE:
0 1 CORRECT ALIGNMENT OF THE PLUNGER WITH THE WATER DRAIN VALVE. N_MM_123228_3_AQM0_02_01

Page 8 of 8
Fuel Sampling For Analysis - Suction Procedure : Fuel Sampling For Analysis - Suction Procedure - Sheet 2
On A/C 401-425 427-428 430-433 435-450 801-900