User Manual FX L 2009

FUNCTIONING OF THE ALARM SYSTEM

SEQUENCE TO ACTIVATE THE ALARM:

1° Remove the contact and take out the starter drum key;
2° Get out of the vehicle and check that all doors, the hood, and the trunk are closed;
Press the "ACTIVATE" button on the remote control.
4° The turn signals will flash once;
5° The siren emits 1 beep;
6° The doors will be locked (only in vehicles with electric locking connection);
7° The windows will close (only in vehicles with electric window connection, requires optional modules);
The LED flashes during the first 20 seconds, according to a certain sequence, which will indicate the area.
from the last shot (according to the following table);
After this time, the LED will flash slowly indicating that the alarm is activated.

Attention! The alarm system will be ready to trigger 20 seconds after its activation.

Sequence of LED flashes: Last shot area:

1 flash Hood/trunk switch.

2 flashes Ultrasonic Sensor.

3 flashes Door switches.

4 flashes Contact actuation.

ALARM ACTIVATED:

1° The LED flashes slowly;

By pressing the 'AUX' button on the remote control, the Locator function will be activated. (lights will flash for 15
seconds.

WHEN THE ALARM GOES OFF:

1° Upon opening the doors;

2° When opening the hood;
3° Upon opening the trunk;
4° Upon activating the contact;
5° Upon detecting the ultrasonic sensor, any type of intrusion in the cabin;
If the 'ACTIVATE' button on the remote control is pressed for more than 3 seconds, the Panic function will start.
(voluntary triggering of the alarm system).

As long as the respective buttons are properly connected to the alarm system.

ALARM TRIGGERED:

1° The siren sounds continuously for 60 seconds;

The turn signals blink for 75 seconds;
3° The LED flashes rapidly;
4° The locking system will be activated.

Observation: This sequence corresponds to a complete firing cycle.

Attention! At the end of each firing cycle, the alarm will reactivate, always keeping the vehicle protected.

1
SEQUENCE TO DISABLE THE ALARM:

With alarm without trigger:

1° Press the "DEACTIVATE" button on the remote control;
2° The lights flash 2 times;
3° The siren emits 2 beeps;
4° The doors will be unlocked (only in vehicles with electric lock connection);
5° If the AUX button is pressed for 2 seconds, the Auxiliary output will be activated.

Notice! Consult your installer about the application of this auxiliary output.

With alarm triggered:

1° Press the 'DEACTIVATE' button on the remote control;
2° The alarm will instantly leave the trigger mode;
If you do not enter the vehicle, the alarm will remain activated.

Notice! If you want to enter the vehicle, follow the steps below.

FUNCTIONS OF THE SYSTEM

CHECK CONTROL:

Whenever the LED of the ultrasound capsule on the driver's side lights up at half brightness, it will be
alerting that one of the entrances (doors, hood or trunk) is open. As long as, said entrance
It is connected to the alarm system.

AUTOMATIC ACTIVATION:

The alarm system allows it to be activated automatically when exiting the vehicle and having
closed all the doors.

RE-ACTIVATION:

. At the end of each firing cycle, the central processing module checks the cause. If the cause still
persists (for example: open door), another firing cycle of 75 seconds starts. Otherwise, the alarm
It will be activated again returning to the monitoring of all entries.

. Also, if after deactivating the alarm, none of the entries (ignition, door, hood, trunk or
ultrasonic sensor) were triggered, within 30 seconds the alarm will be reactivated automatically
(locking the doors), thus protecting against possible accidental deactivations.

SHOOTING CONTROL - INPUT / SENSOR

. After 8 consecutive firing cycles, the control unit cancels the entry (contact, door, hood, or trunk)
what causes the shots, until it returns to its normal condition. After 4 cycles of shooting.
triggered by the Ultrasonic sensor, this is canceled until the alarm is reactivated.
maintaining safety and economizing the vehicle's battery.

AUTO LOCK FUNCTION:

This function "locks" the doors 5 seconds after the contact has been activated;
The doors will "unlock" when the contact is removed. The 2009 line allows you to "cancel" this unlocking, being able to
arrive at the destination and stay in the vehicle with the doors locked.

Important: For your safety, the Auto Lock feature will not activate with the doors open. This prevents locking.
accidental with the key in the contact drum.

REMOTE CONTROL ASSAULT MODE:

The alarm system allows for the immobilization of the moving vehicle by "pressing" the ACTIVATE button.
remote control, as long as the vehicle is in motion.

AUTOMATIC ASSAULT MODE:

. The alarm system allows the vehicle to be immobilized in motion, one minute after being 'turned on'.
vehicle engine;
. This function is disabled by pressing the hidden button located inside the cabin.
2
ASSAULT MODE by DOOR OPENING:

. The alarm system allows for the locking of the vehicle in motion, one minute after "opening" the door, with the
vehicle in motion;
. This function is disabled by pressing the hidden button located inside the cabin.

Attention! The different Assault Modes must be used exclusively by individuals familiar with the system.

Important! If you have any questions about the use or implementation of any of these functions, consult the store that
he installed his alarm system.

USE OF THE PX 42 REMOTE CONTROL

ACTIVE DEACTIVATE

AUXILIARY
PE

OBJECTIVE: ACTION: ALARM RESPONSE:

1 beep and lights confirm activation. 3

Press the ACTIVATE button beeps and lights confirm activation with doors, trunk or
Activate the alarm.
second. open hoods.

2 beeps and lights confirm deactivation. 4

Press the DISABLE button for 1 beep and lights confirm alarm deactivated with trigger in
Deactivate the alarm.
second. absence.

Activation or deactivation of the alarm without an acoustic signal.

Annul
Press the AUX button for 1 second and Only the lights will confirm at that moment,
momentarily the immediately, the button ACTIVATE or activation/deactivation
Acoustic signal. (Beep)
DISABLE.

The alarm will be activated and will emit 2 beeps, informing that it
momentarily suspended the use of the Ultrasound system,
Disable the Ultra sensor
Press the ACTIVATE button for 1 second allowing that, for example: someone remains inside the
sound
and immediately the AUX button 2 vehicle with the alarm activated. The Ultra Sound sensor
momentarily.
seconds. it will be operational again, after completing the
normal deactivation and activation of the alarm system.

The alarm will emit a light flash for 15 seconds, without

With the alarm activated, press the
Locator Function. disable it.
AUX button for 3 seconds.
This output allows to command the opening of the trunk or the
With the alarm deactivated, press the opening of the windows, from the remote control. It can
Auxiliary Function.
AUX button for 3 seconds. require additional accessories.

Press the ACTIVATE button for 3 The alarm will be triggered automatically from the control
Panic Function.
seconds. remote, without turning it on or off.
1 flash of lights lasting 2 seconds, confirms the start of the cycle
Press the ACTIVATE button
Activate Assault Mode. of blocking.
second,with the vehicle in motion.

Gate Command This function requires an additional accessory (PG 150) for
Press the PE button.
Household Electrician. command electric gate or lighting fixtures.

3
 USE OF THE MASTER KEY

Attention! For greater security, the Master key will only operate for 15 seconds after being turned on or
The contact is turned off.

OBJECTIVE: ACTION: ALARM RESPONSE:

The alarm will emit 2 beeps indicating that the
alarm was canceled. Now the system is
Deactivate the alarm.
Activate the contact, press the key
inoperative. This remedy is useful when the
Master until hearing 1 beep of siren.
control or when the vehicle is left to
maintenance or repair.
The alarm will emit 1 beep indicating that the alarm
Activate the contact, press the key
Enable the alarm. Master until you hear 1 beep of the siren.
It was enabled. Now the system is back to being
operant.

Important! If you do not know the location of the Master key, please contact the business that installed the product.

CONSERVATION AND CARE

The water and chemicals used to clean the interior of the vehicle can damage the
ultrasonic sensor, leading to a decrease or extinguishing of its effectiveness. Never use compressed air
to clean the Ultrasonic capsules; they are a fundamental part to protect the interior
of the vehicle. Over time, the batteries of the PX 30 remote control lose their
they are loaded and need to be replaced. The delay in replacing this battery may
reduce the range of the remote control and make the operation of the alarm system difficult.
it is important to conduct periodic tests on the alarm system, especially when it
returns from laundries, workshops, or others. For any inquiries, refer to the store where the transaction was made.
the installation. In this way, the alarm system will always fulfill its role well.

PRODUCT WARRANTY

PST Electronics guarantees this alarm and its components for a period of 03 (three) years.
count from the date of issue of the purchase invoice, against any defects of
manufacturing or in the product components; excluding the batteries or cells provided in the
system.
Within the warranty period, in case of defect, the responsibility of PST Electronics is
limits to repairing or replacing the piece of its manufacturing.
For this, contact the store that installed the product by presenting the original invoice of
purchase.
The repair or replacement of the defective product does not extend the warranty period.
The warranty loses value when: the defective device has been opened by unauthorized persons.
authorized; the purchase invoice was not presented; the product serial number was
scrape unable to identify it; bad treatment, incorrect handling will be checked,
damages caused by incorrect installation, use beyond specifications or leakage of
water, dust, cleaning products, etc.
The installation warranty must be agreed upon between the installation center and the end consumer.
PST Electronics is not responsible under any circumstances for any potential thefts inside or
outside the vehicle, or for the theft of the vehicle itself, or for potential fines and/or others
implications for traffic violations.
PST Electronics reserves the right to make modifications to the product without prior notice.