Key matching: Key match:

Open the software, select series 3, select BCM, choose after-sales function, select body matching, send the old key to
DFSK, enter the new key, take out the new key, place the new key near our ignition switch. The first key is learned.

Open the software, select beings 3, select BCM, select post-sale functions,
select body matching, send the old key password to DFSK, get the new key and
place the new key near our ignition switch. The first key is learned with
success, take out the second new key and place it near the power switch, the second one
Key is learned successfully. The key learning is complete.

Electronic lock release

Use a 3000 watt onboard charging cable to charge the Seres 3, plug it in and lock the car. When we finish charging, first

Charge the Series 3 with the 3000-watt charging cable that comes with the car, plug it in and
finish, lock the car. When we have finished loading, we first unlock the control
central, opening it with our key and obtaining something like a central control code
to unlock it, then our loading gun cannot be unplugged. When the
unlocking fails or the electronic lock gets stuck, our loading gun cannot be
disconnected directly and can be treated with our unlocking method of
emergency. Open the trunk and find the emergency lock inside, the emergency lock
The emergency is in this part, take out our tools, use leverage to open.
the cover and find the lock inside emergency, try our lock inside
emergency to pull out the gun successfully.

Release of electronic handbrake repair:

The EDV motor can be released through maintenance, the operating method is as follows: Step one, plug in our TDS800 instrument, Bluetooth box.

Select seres 3, select EPB, select after-sales service function, select action test, select release, release successful. Release.

The EDV engine can be released for maintenance as follows: Step 1: Connect
our TDS800 instrument, Bluetooth box, select beings 3, select EPB, select the
post-sale function, select action test, select release and successfully release.
The symbol of success of liberation is

Window pinch protection learning

The entire Seres 3 lineup is equipped with a four-door anti-pinching function. The anti-pinching function demonstration shows that after the vehicle triggers the anti-pinching function twice, the anti-pinching function...

It will be lost, at this time it is necessary to learn about the anti-pinch function, learning method, pull, up for 10 seconds, press the switch.

Press three times until the glass is lowered to the lowest point, learning successful.
The Seres 3 includes as standard the anti-pinch function for 4 doors. Demonstration of the function
anti-pinch function, after the vehicle has activated the anti-pinch function twice,
the anti-pinch function will be lost, so it is necessary to learn the function
pinch, to learn, hold up for 10 seconds, press the switch
until the window goes down to the lowest level, press 3 times in a row, you study it successfully.

Forced boot learning

Vehicle, vehicle started successfully, ready indicator, when our brake sensor has a problem and we need to start the vehicle in an emergency.
:
Orange light, keep pressing the switch for about 20 seconds, the vehicle can perform an emergency start, and the vehicle starts successfully.
To start the vehicle normally, the key must be placed in the range that the antenna can.
detect, press the brake, push the one-touch start switch, start the vehicle, the
vehicle starts successfully, shows READY, when our brake sensor has a problem and
We need to start the vehicle in an emergency, we can start it without pressing the brake.
Steps: Place our key near the one-touch start switch, press the
switch, the switch lights up orange, then hold down the
switch, around 20s, the vehicle can be started in an emergency, the vehicle is
starts successfully.

CANDTU:
200 UR is a data device with dual communication and storage capabilities. It comes with a 32GB storage card that allows for long-term storage of CAN message data, making it convenient.

Post-analysis, troubleshoot the fault. Indicator light introduction: PWR: Power indicator light, SYS: System running status light, green light flashes.
The system is operating normally. REC: SD card recording status light, green light flashing, SD card is not full, there is data recorded on the SD card, CAN0:
CAN0 transmission and reception status light, green light flashing, CAN0 channel is normally receiving data, CAN1: CAN1 channel transmission and reception status light, green

The light is flashing, the CAN1 channel is receiving data normally. Prepare to connect the wires, prepare 6 wires, and a screwdriver to connect to pin OBD16.
Connect OBD pin 4 to 200 UR GND pin. Connect OBD pin 12.
Connect pin 13 of the OBD to adapter 1, CAN high, and connect the adapter to CAN Bus.

It is a 2-channel CAN bus data logger with memory. It comes with a card for
32G memory and can store CAN message data for a long time, which
facilitates the analysis and resolution of problems afterwards. Indicators: PWR: Indicator of
battery, SYS: System operation status light, blinking green, the system
It works normally, REC: SD card recording status light, blinking green.
SD card is not full, the SD card has data recording, CAN0: Status light of
transceiver CAN0, blinking green, the CAN0 channel receives data normally, CAN1: Light of
CAN1 transceiver status, flashing green, the CAN1 channel is receiving data normally.
CAN1: Status light of the CAN1 channel transceiver, the green light is flashing, the CAN1 channel received
Usually data. Prepare the wiring, prepare 6 cables, a screwdriver, connect pin 16.
from the OBD to pin YN of the 200 UR. pin 16, pin YN, connect pin 4 of the OBD to pin GND of the 200 UR.
pin 4, pin GND, connect pin 12 of the OBD to adapter 1, CAN high, connect pin 13 of the OBD to
adapter 1, low CAN, connect the adapter to the CAN Bus data logger.
Seres 3 Product Introduction
:
Our hood pull rope, pull twice to open the hood, open our hood, the front compartment contains VCU, 12V auxiliary.
OBC PTC
However, equipment such as PTC heaters. VCU, the vehicle controller, is like the human brain, capable of responding based on the actions taken by people.

And the core controller of other electronic devices in electric vehicles. 12V auxiliary battery: provides power for the low-voltage electrical appliances of the whole vehicle.
Source. Three-in-one controller: includes three types of components, MCU, motor controller, DCDC, DC converter, PDU high voltage distribution.
The electric box, MCU motor controller, converts high voltage direct current into alternating current and interacts with other modules on the vehicle for signal exchange.
Implementation of control for the drive motor. A DC-DC converter is a device that converts high-voltage DC electricity into low-voltage DC electricity for the entire vehicle.
The power source is the power battery and power battery. Since the rated voltage of the whole vehicle is low voltage, a DCDC device is needed to convert.
High voltage direct current is converted into low voltage direct current to ensure the overall vehicle power balance. The PDU high voltage distribution box is the high...

The three main components of an electric vehicle are: the battery, the motor, and the control.
electronic. Now I explain in detail, we find the cord of the motor cover.
Press it twice and open the engine cover. The front cabin contains the VCU, the auxiliary battery.
12V, the 3-in-1 controller, the OBC, the PTC compensating heater, the kettle
compensation of electric motor control, battery cooler, PTC heater, etc.
The VCU, the controller of the entire vehicle, is like the human brain. It can be detected
correctly the driver's intention. It is used to control the start, the operation,
the forward and backward movement, the speed, the stop and other electronic devices of the vehicle
electric. 12 V auxiliary battery: provides power to all low voltage devices of the
vehicle. 3-in-1 controller: contains trestpos of components, MCU, motor controller,
DCDC, DC converter, PDU, high voltage distribution box. MCU, motor controller,
converts high voltage DC energy into AC energy and interacts with other modules in the
vehicle to achieve control of the drive motor. DCDC, DC converter, the
device that converts high voltage DC energy into low voltage DC energy, the source of
Electricity for the vehicle is the battery and power cell. As the nominal voltage of the...
the vehicle is of low voltage, a DCDC device is required to convert the DC energy from
high tension in low voltage DC energy, in order to guarantee the balance of consumption
vehicle energy.

Delayed headlight off

The Seres 3 car has a headlight delay off function. To use this function, first we turn off the ignition switch.

After closing, within two seconds, we continuously toggle the light switch inward, toggling twice, the headlight will turn off after a 30s delay.
Rotate the switch 3 times to delay the front light's shutdown for 60 seconds. If the switch is rotated 4 or more times, the front light's shutdown is delayed for 90 seconds. When we get out of the car.

The Seres 3 has a delayed headlight shut-off function. To use this function,
first we disconnect the ignition and, once disconnected, we pull the lever of the
lights inward in a period of two seconds, twice for a delayed off of 30s,
three times for a delayed shutdown of 60s and four or more times for a delayed shutdown of
90s. When we got out of the car, we closed the door and pressed the unlock button once.
from the key and again the lock one to disconnect the function.
Explanation of the use of cruise control:
The Seres 3 has a cruise control function, which allows us to drive the vehicle on good road conditions or on the highway.

Push the lever inward to enter pre-cruise mode. When the speed exceeds 40 km/h, pull it down to set to activate this function.

The accelerator can be temporarily canceled, and to restore it again, just push the lever up to 'res'. If you want to turn it off completely,

The Seres 3 has a cruise control function that can be used while driving.
by roads in good condition or on the highway. To use the cruise control, we activate
the lever inward, when the car is in pre-cruise mode, and when the speed is
above 40km/h, we press down to activate the function, after which it can be
increase or decrease the speed up or down. If you want to deactivate it
temporarily in the middle, you can do it by pressing the brake or the accelerator, and to resume it
Again, turn the lever upwards to the stop. If you wish to completely deactivate the function,
turn back inward to deactivate the function.

Explanation of child locks and child seat interfaces

for children:

When children travel in the car, they must sit in the back seat and with a car seat for
children. One is underneath the second row of backs and the other is at the rear, which is
you can see behind the backs. When a child travels in the car, in addition to installing the
child seat, the child safety lock must be activated to prevent the child from opening the door from
the interior of the car, which can be seen on the door panel. We operate the switch on the
The direction of the arrow and the child lock is now activated. Now that we have closed the door,
the person inside cannot open the door by pulling the interior handle. We can
open it from the outside by turning the door handle or unlocking the vehicle
directly.

Use of the rear door and emergency opening:

Take a look at the way to open the trunk of this car. In the unlocked state of the vehicle, you can see below the logo, there is a

Take a look at how the trunk opens on this car. With the vehicle
unlocked, you can see below the logo, there is a switch in this position, press it to
open the trunk. In the second case, with the vehicle locked, we bring the key close to the vehicle
and we press this button directly to open the trunk. In case of emergency, there is a
way to open the trunk from the inside. You can see a lid in this position inside,
open this lid and you can see a black paddle inside, turn the black paddle to the right
So we can open the trunk from the inside.

Use of the air conditioning system:

Adjust the air volume, increase the air volume to the right, decrease the air volume to the left. Click this button, and the indicator light will turn on to activate the AC cooling.

The heating function of the fog and frost removal external rearview mirror is turned off when the indicator light is off. The PTC indicator light is used for heating in winter, and again
Click to disable this feature. To turn off the air conditioning, click off.
Take a look at the air conditioning system of this car. The air conditioning can be
connect by turning the air volume adjustment switch. Once connected, the volume of
The air can be adjusted by turning it left and right, increasing the volume of
air to the right and decreasing it to the left. Click this button and the light will
turn on to connect the air conditioning refrigeration compressor. Press again
this button and the light turns off, turning off. The right button adjusts the temperature, to the right
to increase the temperature, to the left to decrease the temperature, press this button
to turn on the automatic air conditioning. If you want to disconnect the air conditioning
automatically, adjust the air flow rotary button. By clicking on this button, it gets activated
air supply mode. By clicking this button, the defrosting is activated and the
defrosting the front windshield. By clicking this button when the light is yellow,
The internal circulation is activated when the light is off, the external circulation when it is on.
this button is the rear windshield defrost heating function and the
mirror defrosting, when the light goes off, it is off. The PTC light is used
for heating in winter, click again to deactivate this function. To disconnect
the air conditioning, click to turn off.

Energy recovery: Recycling of energies:

This car has an energy recovery feature. There are three levels of energy recovery: weak, medium, and strong. When the energy recovery is set to...

We can set its level through the central control screen, but there are certain conditions for the settings, for example, in sports mode.
In the mode, it can only be set to weak; in normal mode, it can be set to weak and medium; in eco mode,
You can set it freely. Let's take a look at how to set it. If you want to set the energy recovery, click on my car, and then click

This vehicle has energy recovery. There are 3 levels of energy recovery: weak,
average and strong. The stronger the level of energy recovery, the stronger the rate of
deceleration when the accelerator is released, but at the same time the range is greater.
the level can be adjusted through the central console, but there are certain conditions, for example,
in sports mode it can only be adjusted to weak, in normal mode it can be adjusted to weak and
medium, and in eco mode it can be freely adjusted. If you want to set the level of
energy recovery, press on my car, press on energy management, press on recovery
of energy level and you will see that there are three levels to choose from: weak, medium, and strong.

Fatigue driving alert:

Set it, click OK to enter, where you can choose the time, 2 hours, 3 hours, click OK to select.
We can set a time on the board. If we drive beyond the established tempo, the
the vehicle will give us an alert. To see how to configure this, lower the configuration menu and here
you will find the fatga reminder configuration, click ok to enter and here you can
select the time, 2 hours, 3 hours, click ok to select.

Explanation of the use and initialization of the sunroof:

Explanation of the use of the speed limit function:

The speed limit can be increased or decreased. The adjustable range for the speed limit is from 30 km/h to 130 km/h. If you want to turn off this feature, turn this dial.

We can set a speed limit that will help us better control the speed of
car, see how to do it. By pushing the lever outwards, the speed limit is activated.
it can be increased or decreased by moving the lever up or down. The limit of
speed can be activated from 30km/h to 130km/h. To deactivate this function, push the
lever outward.

The added function of the keys:

Let's take a look at the special features on the smart key. The first one is the remote window lift function, which is activated by pressing and holding the unlock button for 2 seconds.

Press and hold again, it will continue to open. If you want to close the sunroof and all windows, we press and hold the lock button for more than 2 seconds.

The remote control key can control the sunroof, and settings can also be made. Click on 'my car', then click on 'vehicle personalization settings', where you can view it.

Take a look at the special features of the smart key. The first is the function of
remote electric windows. When we hold down the unlock button for
more than 2s, the sunroof and all the windows will open, and when we release this button during
the process will stop in this current position. We hold down the button again and it
keep opening again. If we want the solar roof and all the windows to close,
we hold down the lock button for more than 2s, at which point it will close
all the windows. The second is the car search function, which allows you to find the
car by pressing the search button on the key. The sunroof can also be configured with
remote control, click on my car, click on vehicle customization, here you can see
the solar roof with remote control and you can see the different options.

Parking function:

Pulling the handbrake like this achieves an emergency braking effect. If we are in P or N gear, turn off the power.
When it's off, the handbrake will automatically engage. The position at the lower end of the handbrake is the autohold parking switch. Press it to activate this feature.

This car is equipped with an electronic handbrake, located in this position on the
central console. Press the brake pedal and press it, the indicator light turns off and the handbrake is
release. If it rises and the indicator light turns on, the handbrake is being raised. If the
brakes fail, we can apply an emergency brake by pressing and holding the brake.
hand up. If we are in P or N and disconnect the ignition switch, the brake will
the handbrake will be applied automatically. At the bottom of the handbrake is the
parking switch with automatic hold. After pressing it and activating the function, the
the vehicle will remain in a deactivated state even after we have pressed the pedal
automatic and the vehicle becomes completely disabled, even if we release the pedal
automatic. When we step on the accelerator again, the vehicle operates normally.