1 2 3 4 5 6 7

SEPARATOR
DEVICE MOUNTING HEIGHTS (PER NFPA 72)
NFPA 72 2002 EDITION END SECTION THREE LEVEL SENSOR
I 8 esa
O r- CO o

NFPA 72 2007 EDITION END SECTION TERMINAL BLOCK

VISUAL APPLIANCE MOUNTING HEIGHT CONSIDERATIONS IN SLEEPING ROOMS A/C SUPPLY (SECTION A.5.6.3.1) ELECTRICAL TO PROVIDE GROUND
ROD OR GROUND TO WATER 1/8" WIDE GROUND RING -
1. MIN DISTANCE IN SLEEPING ROOMS IS 24" (610mm) TO TOP OF LENS D FFUSER THE 4" REQUIREMENT FOR SMOKE DETECTORS HAS PIPE WITH 1/4" WIDE BRAIDED WIRE 4"DIA & BELOW (TYP)
FOR 110CD STR0BES WITHIN 16' 0F THE PILLOW BEEN REMOVED FROM THE 2010 EDITION OF NFPA 72 (SEE NOTE 2)
2. 177CD STR0BES, USED IN SLEEPING ROOMS, CAN BE WITHIN THE 24" FEED THROUGH END _L_
NOTE: MEASUREMENTS TERMINAL BLOCK . SECTION
F (610mm) MINIMUM DISTANCE FROM THE CEILING. THE HIGHER 3'(MIN) 02 m) SHOWN ARE TO THE
INTENSITY IS TO COMPENSATE FOR A POSSIBLE SMOKE LAYER. (914mm MIN) (TYPICAL OF 10) PUMP A
CLOSEST EDGE OF THE
CEILING DETECTOR.

CEILING MOUNTED Ø |Ø o
FOR CEILING HEIGHTS LESS THAN 86" (2180mm), NFPA 72 AUDIBLE APPLIANCE SMOKE/HEAT 4" 00000000
THE VISUAL LENS MOUNTING HEIGHT SHALL BE 6" MIN (152.4mm MIN) DETECTOR (102mm) 12" (MAX) 0
WITHIN 6" (150mm) OF THE CEILING. AUDIBLE ONLY BELOW FINISHED CEILING (305mm MAX) DIN RAIL DIN RAIL
HEAT DETECTORS END BLOCK 042 END BLOCK
90" MIN (2286mm MIN) ACCEPTED HERE NEVER HERE
SEE NOTE 4 ~
ABOVE FINISHED FLOOR SEE NOTE 5 -
AUDIBLE/VISUAL IR (OTHER MOUNTING HEIGHTS SHALL BE 1" WIDE WIREWAY FOR WIRES FROM PLC
& VISUAL ONLY PERMITTED BY THE AHJ PROVIDING IT NFPA 72 2010 EDITION
APPLIANCES MEETS THE SOUND LEVEL OUTPUT REQUIRED.)
WALL MOUNTED (SECTION 1 7.7.3.2.1)
3/4"C(3#12) [ 4-20mA D-C BID SET
SIGNAL TO
96" MAX (NFPA) TO EXIT DOOR SMOKE/HEAT PUMP B RECEIVING DEVICE
SYNCHRONIZE MORE THAN 3/4"C(2/C-#18 SHLD)
(2440mm MAX) 5' (MAX.) DETECTOR
TWO APPLIANCES IN ANY (1524mm) fi TRANSMITTER (NOTE 1)
ABOVE FINISHED FLOOR DOOR 00000000 O
FIELD OF VIEW. Ø |Ø o LO
E NFPA 72 2002 EDITION --m--W-ID-T.l-l__m,,. 99999999 mm - GROUP WALL MOUNT
LESS 3" CABLE 1 e
(SECTION A.7.5.4.2.5) (76mm)
NFPA 72 2007 EDITION
(SECTION A.7.5.4.4.5) IN AUTO FLOOR
SIDE WALL
NFPA 72 2010 EDITION RUNNING
(SECTION 18.5.4.3.2(4)) MANUAL DIRECTION SPEED
ALARM START/STOP NOTES:
PULL
STATION CABLE 3
5" 1. LOCATION FOR TRANSMITTERS NOT INTEGRALLY MOUNTED ON THE FLOW METER.
80" (ADA) (2032mm) CABLE 2
2. GROUND MAGMETERASINSTRUCTED BYTHEVENDOR.
REF. 80" MIN (IBC) 80" MIN (NFPA) (2032mm MIN) PHONE MAGNETIC
(2032mm MIN) NFPA 72 2002 EDITION JACK - DOOR FIBERGLASS BOX, TYPE 4X, SOLID COVER 3. STARTUP AND COMMISSIONING TO BE BY MANUFACTURERS REPRESENTATIVE.
REF. 96" MAX (IBC) (SECTION 7.5.4) 042 HOLDER (12"x8"x7") WITH 8.75"x6.88" SUBPLATE COMMISSIONING REPORT TO INCLUDE ALL CONTROL PARAMETERS.
NFPA 72 2007 EDITION O
NOTES:
1. COMPRESSION-MOLDED FIBERGLASS MATERIAL 4. POWER WIRING, 3/4"C(4#12) OR AS SUPPLIED BY MANUFACTURER.
(2440mm MAX) (SECTION 7.5.4.1)
WALL 2. SEAMLESS FOAM-IN-PLACE GASKET ASSURES WATER-TIGHT AND DUST TIGHT SEAL
ABOVE FINISHED FLOOR NFPA 72 2010 EDITION 5. SIGNAL WIRING, 3/4"C(6/C-#18SHLD.) OR AS SUPPLIED BY MANUFACTURER.
3. THREADED INTERNAL BOSSES FOR SUB PLATE.
(SECTION 18.5.4.1) 48" MAX (ADA) (1219mm) 4. QUICK-RELEASE LATCHES WITH CORROSION-RESISTANT POLYESTER HINGES AND
42" MIN/54" MAX (NFPA) (1067mm MIN/1372mm MAX) POLYESTER LATCHES WITH A TYPE 316L STAINLESS STEEL BAIL. ATTACHED WITH TYPE
316 STAINLESS STEEL SCREWS.
NOTE: REFER TO THE PROPER DEVICE FINISHED NFPA 72 2002 EDITION 5. 316L STAINLESS STEEL PADLOCK HASP.
INSTALLATION INSTRUCTIONS
FOR BACKBOX MOUNTING HEIGHT. NFPA 72 2007 EDITION NFPA 72 2010 EDITION
(SECTION 5.13.4) (SECTION 17.1 4.4) TERMINAL BOX PANEL LAYOUT 20-FIT MAGNETIC FLOW METER INSTALLATION
NO SCALE SEE "DEVICE BOX CONDUIT DETAIL" FOR INSTALLATION

I
l--
O
cû

USE ONLY UL LISTED FIRE ALARM SIGNALING LINE (ADDRESSABLE) CIRCUITS SHIELDING EXAMPLE ,
S FOR MAP E DATA COMM. UL LISTED FIRE PROTECTNE SIGNALING CABLES MAY BE SELECTED FROM THE SIMPLEXGRINNELL WIRE & CABLE TABLE, #WIRE TABLE _ _
LINES, AUDIO, PHONE & SPEAKER
. S 1 -2 SO D TP.
CUT EXAMPLE:
O2 #18-2 AWG SHIELDED 042
SHIELDS AND DRAINS MUST NEVER TOUCH GROUND.
/TWISTED-PAIR CABLE 042
MOST GROUNDS ARE DUE TO SHIELDING ISSUES.
SUN SHADE
042
MOST SHORTS ARE SHIELD TO CONDUCTOR. SUN SHADE
UV AND CORROSION
C 042
BY CREATING A PROPER PROCEDURE FOR WIRE UV AND CORROSION
cd TRIM AWAY ONLY HANDLING WITH ADDRESSABLE CIRCUITS 316 STAINLESS STEEL (SST) RESISTANT
TKH S ELDDR MOST GROUNDS AND SHORTS CAN BE ELIMINATED.
ABS MATERIAL MOUNT DISPLAY, PLATE & 316 THICK SST STRUT ABS MATERIAL
WIRE UNDAMAGED ALL
042 UNSHIELDED WIRE MUST BE ENTIRELY IN GROUND CONDUIT. TAP FOR LEVEL SENSING, PAINTED WHITE TRANSMITTER, AND MIN., OR 3" STRUCTURAL SST CHANNEL Z
042
CONDUIT SYSTEM MUST HAVE A GOOD REFERENCE TO EARTH GROUND SEE SHEET D-7104 (TYP) CURRENT TO FIBER (TYP) PAINTED WHITE O
042
PIGTAILS MAY BE NOT BE USED IN FIRE ALARM APPLICATION. (TYP)
o SHIELD CONVERTER IN SAME
ENCLOSURE.
(TYP) MOUNT DISPLAY, TRANSMITTER, AND
O PREPARE THE CABLE BY DRAIN WIRE EXAMPLE FOR NO.10GA.TYPE316 CURRENTTOFIBER CONTROL PANEL
REMOVING 2" TO 4" 0F
JACKET AS NEEDED. © WIRING LABELING STAINLESS STEEL IN SAME ENCLOSURE.
O (SST)PLATE & NO.12 GA. (TYP) 0-FIT l--
WIRE
TAG THICK SST STRUT MIN., OR 1 <
REUSE INSULATION DI D
u GENERAL WIRING GUIDELINES 3" STRUCTURAL SST CHANNEL
1. ALL WIRING IS TO BE COPPER CONDUCTOR. ALL EQUIPMENT MUST
® (TYP) - 70-LIT 0-LS 0-LSH
CLASS 'B' 1 1 1
BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURERS
RECOMMENDATIONS AND THE SPECIFICATIONS AND STANDARDS <
z 0F THE AUTHORITY HAVING JURISDICTION. THE INSTALLATION OF DRAIN WIRE TO PREVENT CONFUSION AND POSSIBLE
ALL WIRING, CABLE AND EQUIPMENT MUST BE IN ACCORDANCE ERRORS, ALL WIRES MUST BE TAGGED.
.. WITH NFPA 70, NATIONAL ELECTRICAL CODE NEC), AND SPECIFICALLY SEE WIRE LEGEND FOR TYPES. SIX 1-5/8" UNISTRUT FLOOR CONDUIT
F- WITH ARTICLE 760, FIRE ALARM PROTECTIVE SIGNALING SYSTEMS; EXOTHERMIC WELD (EPOXY ANCHOR) PVC COATED
WIRES MUST BE CONNECTED
ARTICLE 800, COMMUNICATION CIRCUITS, WHERE APPUCABLE. SEPARATELY UNDER TERMINALS. TO PIPE AND RISER ---------._.___ TYP RMC Z
I 2. IF SHIELDED WIRE IS USED, THE FOLLOWING MUST BE OBSERVED: DRAIN WIRE A CONTINUOUS WIRE LOOP LIQUID TIGHT
- A. METALLIC CONTINUITY OF THE SHIELD MUST BE MAINTAINED AND (+) IS NOT ALLOWED.
B INSULATED THROUGHOUT THE ENTIRE LENGTH OF THE CABLE. STRIP OFF APPROX. RED ONE CONDUIT TO CONTROL PANEL FLEX CONDUIT
B. SHIELDS SHALL ONLY BE CONNECTED AT THE CONTROL UNIT. 1-2 INCHES OF PUSH REUSED INSULATION ONLY CLASS B IDNET, MAPNET OR PVC COATED ONE CONDUIT TO LIGHTING PANEL
SHIELD MUST NOT BE CONNECTED TO, OR TOUCH CONDUIT, ELECTRICAL BLACK INSULATION TO CAREFULLY DOWN INTO RMC (SEE TRENCH DETAIL)
BOXES, OR ASSOCIATED HARDWARE AT ANY POINT. SLIDE ONTO DRAIN WIRE. JACKET. SECURE WEH DATA COMM. CABLE MAY BE
C. THE ENTIRE LENGTH OF THE CABLE MUST HAVE A RESISTANCE GREATER ELECTRICAL TAPE. T-TAPPED. IT MUST BE DONE
ü- THAN 1 MEG0HM TO EARTH. IN A JUNCTION BOX WITH l..L.I
D. ALL CONDUCTORS ARE TO BE FREE OF SHORTS AND GROUNDS. BLACK CABLE STRAIN RELIEF l.E.
3. UNDERGROUND WIRING MUST BE LISTED FOR APPLICATION AND FREE OF ALL WATER. CORD CLAMP/BUSHING, AND
4. WIRING OTHER THAN THAT CONNECTED TO ELEVATOR CABS MUST NOT BE RUN TAPE WRAPPED AS SHOWN HERE.
IN ELEVATOR SHAFTS (REF.NFPA 70, ARTICLE 620). REDUCE EXPOSED WIRES TO
5. WIRING IN DUCTS, PLENUMS AND OTHER AIR HANDUNG SPACES MUST BE LISTED ABOUT 5/16" TO 3/8" FOR DRAIN WIRE
FOR PLENUM USE AND INSTALLED IN ACCORDANCE WITH NFPA 70, ARTICLE 300. INSERTION INTO BOX-TYPE STRIP THE INSULATED WIRES
ós 6. SPLICING IS PERMITTED IN ACCORDANCE WITH NFPA 70. ALL JUNCTIONS MUST OR SCREW-CLAMP TERMINALS. ABOUT 5/16" TO 3/8" FOR
O BE INSULATED AS SOUNDLY AS THE ORIGINAL JACKET. CONTINUITY OF ANY SHIELD TAPE INSERTION INTO BOX-TYPE OR
o - (WHERE USED) MUST BE MAINTAINED. LECTRICAL SCREW-CLAMP TERMINALS ON
7. ONLY SYSTEM WIRING CAN BE RUN IN THE SAME CONDUIT. THE ADDRESSABLE DEVICE.
8. THE COMMUNICATION CIRCUE MEETS THE OPERATIONAL CHARACTERISTICS DEFINED FOR A STYLE 4
AND STYLE 6 SIGNALING LINE CIRCUIT. MAXIMUM WIRE RUN NOT TO EXCEED 2500 FT. ...
9. ALL CIRCUITS ARE SUPERVISED AND POWER-LIMITED UNLESS OTHERWISE INDICATED. SHIELD WIRES ARE NOT SUPERVISED. SECURELY TWIST
10. OPERATING POWER, FOR IDNet DEVICES, MUST ORIGINATE FROM A POWER-UMITED POWER SUPPLY USTED FOR FIRE DRAIN WIRES
PROTECTIVE SIGNALING USE OR, FROM THE F.A. CONTROL PANEL POWER SUPPLIES INDICATED IN THE APPROPRIATE THE SHIELD/DRAIN IS NEVER / TOGETHER INTO
DIAGRAM. MAXIMUM WIRE NOT TO EXCEED 1KM (3270 FT). CONNECTED TO THE DEVICE. WIRE NUT. O
11. WHEN COMMUNICATION WIRING OR OPERATING WIRING LEAVES THE BUILDING, OVERVOLTAGE PROTECTORS ARE WIRES MUST BE æ
REQUIRED; USE 2081-9044, INSTALL ONE WHERE E LEAVES THE BUILDING AND ONE WHERE IT ENTERS THE NEXT BUILDING. TIGHT ENOUGH
12. TO PREVENT CONFUSION AND POSSIBLE ERRORS, TAG ALL CONDUCTORS, CODE AT INSTALLATION, TO IDENTIFY TO HOLD SECURELY ONE CONDUIT TO CONTROL PANEL 4/0 GROUNDING CABLE 4/0 GROUNDING CABLE
CIRCUIT ASSIGNMENT, POLARRY AND IN OR OUT DIRECTION OF THE WIRING. LOG ON AS-BUILTS. AND NOT SLIP OUT Project No.: 200-11740-10003
A 13. LEAVE ADEQUATE SLACK IN THE WIRING TO ALLOW FOR TROUBLE SHOOTING.
TWIST THE BARE DRAIN OF WIRE NUT. ONE CONDUIT TO LIGHTING PANEL EXOTHERMIC WELD TO GROUNDING RING EXOTHERMIC WELD TO GROUNDING RING
WIRES TOGETHER AND TRIM
SIMPLEXGRINNELL IS NOT RESPONSIBLE FOR ELECTRICAL CONTRACTOR'S WIRE CONDITIONS. Designed By: CSW
14. IDNet COMMUNICATION LINE SPECS.:
TO ABOUT 1-1/2". JOIN
THEM WITH ELECTRICAL WIRE WASHWATER ELEVATED Drawn By: TAC
o
MAX. 36 VDC 0 .5A
3333 BAUD
15. IDNET MAXIMUM NUMBER OF DEVICES:
NON-CODED 250
NUT.
0-LS 70-LIT STORAGE TANK LAYOUT 70 T MAGNETIC FLOW METER LAYOUT Checked By: DAB
33Q MAX. LINE RESISTANCE CODED PIEZO BASES 43 MAX. SEE ELEVATED STORAGE TANK LEVEL SENSOR DETAIL ON SHEET E-9504 SEE MAGNETIC FLOW METER INSTALLATION"
o 217 ADDRESSES STILL AVAILABLE FOR OTHER DEVICES. l--
0-LSH 42-FIT
¬e
o

o
1 1
E-9511 i O

Bar Measures 1 inch