Scribd
Upload
129 views2 pages

10B17EC271

The document outlines the experiments to be performed in the Basic Electronics lab for the B.Tech Second Semester students of ECE, CSE, IT and BT. It lists 12 experiments involving plotting characteristics of diodes, zener diodes, transistors and JFETs. Experiments also include implementing rectifier circuits, clipper and clamper circuits, and designing an oscillator circuit. It also provides the evaluation plan for the course with marks distribution for projects, mid-sem and final exams, continuous evaluation and attendance. Finally, it lists 3 reference books for the course.

Uploaded by

Shivam Maurya
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
129 views2 pages

10B17EC271

The document outlines the experiments to be performed in the Basic Electronics lab for the B.Tech Second Semester students of ECE, CSE, IT and BT. It lists 12 experiments involving plotting characteristics of diodes, zener diodes, transistors and JFETs. Experiments also include implementing rectifier circuits, clipper and clamper circuits, and designing an oscillator circuit. It also provides the evaluation plan for the course with marks distribution for projects, mid-sem and final exams, continuous evaluation and attendance. Finally, it lists 3 reference books for the course.

Uploaded by

Shivam Maurya
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Department Of Electronics & Communication Engineering

BASIC ELECTRONICS LAB


(10B17EC271)
B.Tech Second Semester (ECE /CSE /IT /BT)

List of Experiments

Experiment No. 1: To plot the characteristics of a diode in forward and reverse biased conditions.

Experiment No. 2: (a) To plot the zener diode characteristics and find the zener voltage
(b) To plot its transfer characteristics for a given load

Experiment No. 3: To implement diode clipper circuits and observe the output waveforms on the
CRO.

Experiment No. 4: To implement diode clamper circuits and observe the output waveforms on
the CRO.

Experiment No. 5: To implement a Half-Wave Rectifier circuit with and without a capacitive filter
and to calculate its ripple factor

Experiment No. 6: To implement a full-Wave Rectifier circuit with and without a capacitive filter
and to calculate its ripple factor

Experiment No. 7: To plot input and output characteristics of a transistor in common-base configuration

Experiment No. 8: To plot input and output characteristics of a transistor in Common-Emitter configuration

Experiment No. 9: To plot magnitude response curve for a Emitter follower amplifier and to determine its
midband gain and bandwidth

Experiment No. 10: To plot the drain and transfer characteristics of a JFET in common-source configuration
Experiment No. 11: To implement and verify the operation OP-AMP based adder and subtractor circuit
using 741 IC.

Experiment No. 12: To design and implement a Wein Bridge Oscillator to generate a sinusoidal
wave of frequency f
o
=1KHz.




Jaypee University of Information Technology,Waknaghat
Department of Electronics & Communication Engineering

Evaluation Plan

1. Project Assignment 10 Marks
2. Mid Sem Evaluation 20 Marks
3. Continuous Evaluation 20 Marks
4. Final Evaluation 40 Marks
5. Attendance 10 Marks
Total Marks 100 Marks

Text and Reference Books
1. Boylstad and Nashelsky, Electronic Devices and Circuit Theory, PHI, 8e, 2001.
2. Morris Mano, Digital Design, PHI, 3e, 2002.
3. N N Bhargava, Basic Electronics and Linear Circuits McGraw Hill Education, 2nd
Editon, 2013.










Jaypee University of Information Technology, Waknaghat

You might also like