TL60 COMPACT WHEEL LOADER
Brief Specications*
Operating Weight
8,598 lbs (3,900 kg)
Net Engine Power
50 hp (37 kW)
Tipping Load, straight
6,063 lbs (2,750 kg)
Tipping Load, articulated
5,456 lbs (2,475 kg)
Operating Load, articulated 2,727 lbs (1,237 kg)
Bucket Capacities
0.471.53 yd3 (0.61.0 m3)
* With rear axle weights 375 lbs (170 kg).
Hydrostatic drive provides the high speed, low torque effort when you are
traveling across a jobsite, then changes to high torque, low speed when
you demand greater traction and more power.
Transverse-mounted diesel engine provides additional counterweight
to the rear of the machine for greater stability and improved loader
performance. Transverse mounting also provides ample access for easier
engine service.
Oscillating rear axle provides stable operation on uneven ground while
maintaining 4-wheel traction for greater operator comfort and control.
Single pin articulated joint provides a more stable platform and less need
for adjustments and maintenance.
Hydrostatic drive provides dynamic braking and helps increase service
brake life.
Specifications
Operating Specifications (standard equipment)
Tires
Operating weight (SAE J 1197)
8,598 lbs (3,900 kg)
Standard
Tipping load, straight at full reach
6,063 lbs (2,750 kg)
Optional tires available, see options section.
Tipping load, articulated at full reach
5,456 lbs (2,475 kg)
Operating load, fully articulated
2,727 lbs (1,237 kg)
Total length, bucket on ground
15 8 (4.78 m)
Total width
5 7 (1.70 m)
Turning radius at outside bucket edge
12 8.4 (3.87 m)
Wheelbase
77 (1.95 m)
Height (top of cab)
8 0 (2.44 m)
Engine
Manufacturer, model
Deutz, D2011 L04
Type
Combustion
4-cylinder diesel engine
4-stroke cycle, direct fuel injection
Displacement
189 in3 (3.1 L)
Net power rating at 2,300 rpm (SAE J 1349)
50 hp (37 kW)
Cooling system
Oil
Electrical System
Nominal voltage
Battery
12 V
12 V / 74 A / 680 CCA
Hydrostatic drive is closed circuit and independent from loader hydraulics. Automatic adjustment
of drawbar pull and speed. Forward and reverse selected from joystick. Innitely variable speed
control in forward and reverse. 4-wheel drive from reduction gear on rear axle via drive shaft to
front axle.
Articulated with nal position damping on both sides, fully
hydraulic through load-sensing priority valve. Quick and easy
steering even at engine idle-running speed.
Total steering angle
Fuel tank
20 gal (75 L)
Hydraulic system (including tank)
13 gal (49 L)
Hydraulic System
Pump capacity
Maximum working pressure
3,625 psi (250 bar)
Loader frame with true parallel linkage and a manual SSL
quick coupler. Z-bar loader linkage available as an option.
General purpose bucket (SAE J 742)
7,425 lbs (33,028 N)
8,325 lbs (37,031 N)
Drawbar pull
6,800 lbs (3,002 daN)
Operator Station
Front: Rigid planetary nal drive axle, limited slip-type differential.
Rear: Oscillating (with cushioning) planetary nal drive axle with integrated reduction gear.
Limited slip-type differential. Axle weights, 375 lbs (170 kg), standard.
Rear axle oscillation
12
Brakes
Service brake: Hydraulically actuated center-mounted drum brake acting on all 4 wheels via
4-wheel-drive.
.65 yd3 (0.50 m3)
Lift capacity at ground level
(SAE J 732)
Breakout force at bucket edge
(SAE J 732)
* With rear axle weights 375 lbs (170 kg).
11 gpm (41 Lpm)
Control unit: Proportional hydraulic valve with 3 control
circuits and high-speed valve for tilting; single, four-way
lever (multi-function lever) for lift and dump cylinders with
integrated travel direction selector switch. Float position in
control circuit lowering and electro-hydraulically operated.
Additional control circuit including quick couplers and
continuous operation function provided as standard.
0-4 mph (0-7 km/h)
0-13 mph (0-20 km/h)
Parking brake: Mechanically operated drum brake at front axle.
80
Service Refill Capacities
2 speed ranges:
Low
High
Axles
Steering
Loader Frame
Power Transmission
Auxiliary brake: Hydrostatic drive provides dynamic braking.
12.5 x 16.5 EM 14
Low prole rubber-mounted full-vision, open ROPS canopy,
ROPS (SAE J 1040) and FOPS (SAE J 231) certied.
Entry from either side and easily cleaned oor.
Operators seat is weight-adjustable and includes hydraulic
cushioning and lap belt
Back-up alarm
Two front working oodlights.
COMPACT WHEEL LOADER TL60
Dimensions: General Purpose Bucket
80
23"
(580 mm)
4'
50
8' 0" (2.44 m)
8' 3" (2.52 m)
10' 2" (3.12 m)
45
5' 5" (1.65 m)
40
Capacity (SAE J 742) 0.94 yd3 (0.72 m3)
Density of material: Max. 2,700 lbs/yd3 (1.6 t/m3).
m)
12' 8" (3.87 m)
Dimensions: Multi-Purpose Bucket
13" (335 mm)
Capacity (SAE J 742) 0.78 yd3 (0.60 m3)
Density of material: Max. 2,700 lbs/yd3
(1.6 t/m3)
Operating load, complete lift
range: 2,355 lbs. (1,066 kg)
with rear axle weights.
8' 11" (2.72 m)
mm)
3" (75 mm)
18" (450 mm)
45
0
38" (96
4' 3" (1.31 m)
26"
(660 mm)
24"
(620 mm)
8' 2" (2.49 m)
10' 3" (3.12 m)
4' 0" (1.23 m)
9' 7" (2.95 m)
m)
70
15' 8" (4.78 m)
Dimensions: Fork Lift Attachment
2.8" (70 mm)
17' 0" (5.17 m)
Fork Lift Attachment (optional)
Operating load (SAE J 1197)*
Width of fork carrier
Fork tines:
(1.
83
m)
3' 10" (1.18 m)
(1.
6' 5" (1.95 m)
0"
33
6"
2.7" (70 mm)
(1.
35
5'
120
6'
4"
16"(410 mm)
11
15' 9" (4.81 m)
Examples of Material Densities
2,253 lbs (1,022 kg)
49 (1,240 mm)
35 (900 mm) long
4 (100 mm) wide, 1.5 (40 mm) tall
Stability factor on level and solid ground
Load center from fork attachment point
18 (450 mm)
Earth (top soil)
2,550 lbs/yd3 (1,512 kg/m3)
Clay (dry), clay & gravel (wet), earth with sand & gravel
3,100 lbs/yd3 (1,839 kg/m3 )
Earth (dry)
2,650 lbs/yd3 (1,572 kg/m3)
Gravel (sandy), gravel (wet)
3,700 lbs/yd3 (2,195 kg/m3)
Earth (moist), clay with gravel (dry)
3,000 lbs/yd3 (1,780 kg/m3)
Clay (natural bed), clay (wet)
3,500 lbs/yd3 (2,077 kg/m3)
Earth (compacted), gravel (dry)
3,000 lbs/yd3 (1,780 kg/m3)
* With rear axle weights 375 lbs (170 kg).
Dimensions: Buckets
General purpose bucket with bolt-on cutting edge
Capacity
Width
.75 yd3 (0.57 m3)
66 (1675 mm)
3
Examples of
)
73 (1855 mm)
.83Material
yd3 (0.65 mDensities
General purpose bucket with bolt-on cutting edge
General purpose bucket with bolt-on cutting edge
.89 yd3 (0.68 m3)
78 (1980 mm)
General purpose bucket with bolt-on cutting edge
.95 yd3 (0.72 m3)
84 (2135 mm)
Light material bucket with bolt-on cutting edge
1.41 yd (0.80 m )
78 (1980 mm)
Light material bucket with bolt-on cutting edge
1.53 yd3 (1.00 m3)
84 (2135 mm)
Multi-purpose bucket with bolt-on cutting edge
.47 yd (0.60 m )
66 (1675 mm)
Multi-purpose bucket with bolt-on cutting edge
.53 yd3 (0.50 m3)
73 (1855 mm)
Multi-purpose bucket with bolt-on cutting edge
.57 yd3 (0.65 m3)
78 (1980 mm)
Scrap grapple bucket, bolt-on cutting edge
.45 yd (0.34 m )
66 (1675 mm)
Scrap grapple bucket, bolt-on cutting edge
.49 yd3 (0.37 m3)
72 (1675 mm)
Scrap grapple bucket, bolt-on cutting edge
.53 yd (0.41 m )
78 (1980 mm)
Scrap grapple bucket, bolt-on cutting edge
.58 yd3 (0.70 m3)
84 (1980 mm)
Utility bucket, bolt-on cutting edge
.77 yd3 (0.59 m3)
66 (1675 mm)
Utility bucket, bolt-on cutting edge
.86 yd (0.66 m )
73 (1855 mm)
Utility bucket, bolt-on cutting edge
.92 yd3 (0.70 m3)
78 (1980 mm)
Optional Equipment / Accessories
Operator Station / Canopy
Other Options
Air-cushioned operators seat with orthopedic lumbar support, adjustable armrests and headrest.
Backup alarm, activated on demand
Rotating beacon, yellow
Belly guard, heavy duty
Tilt and height adjustable steering wheel
Biodegradable hydraulic oil / Ester Base VI 68
Working oodlight (rear)
Creeper drive
Loader Attachments
Electric refueling pump
Bale spear
2,000 lbs. (907 kg) capacity
Immobilizer (anti-theft device)
Bucket teeth
Loader lock-out bar
Crane jib with rigid arm
Manual throttle with transmission deactivated
Cutting edges for buckets
Pilot-controlled hose rupture protection valves for lift
and tilt cylinders
Fork lift attachment with forks:
Carrier: 49 (1,240 mm) wide
Tines: 35 (900 mm) long, 4 (100 mm) wide, 1.5 (40 mm) tall
Pressureless open return line
Load hook attachable on pallet forks
Ride control system
Scarier, 40 (1.01 m) with ve shanks
Spare wheel with tire
Tires
Special paint color
365/70 R 18 SPT 9 Dunlop
Terex Track (gps locator)
Z-Bar loader linkage (less parallel lift linkage)
Other attachments and tire options available on request.
Effective date: May, 2009. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings
in this document are for illustrative purposes only. Refer to the appropriate Operators Manual for instructions on the proper use of this equipment.
Failure to follow the appropriate Operators Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or
death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex
makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation
and/or its subsidiaries in the USA and other countries. All rights are reserved. Terex is a registered trademark of Terex Corporation in the USA and
many other countries. Copyright 2009 Terex Corporation.
Terex Corporation
840 Lily Lane, Grand Rapids, MN 55744
Tel +1 (800) 346-5954 Fax +1 (218) 327-2376
www.terex.com
TL60 2.5K 0509C Part No. 109275
