Fluke 114, 115, 116 and 117
Digital Multimeters
Extended specifications
Technical Data
General specifications (all models)
Accuracy is specified for 1 year after calibration, at operating temperatures of 18 C to 28 C, with relative humidity of 0 % to 90 %.
Maximum voltage between any
terminal and earth ground
600 V
Surge protection
6 kV peak per IEC 61010-1 600 V CAT III, Pollution Degree 2
W Fuse for A input
11 A, 1000 V FAST 17 kA Fuse (Fluke PN 803293)
Display
Digital: 6,000 counts, updates 4/sec; Bar Graph: 33 segments, updates 32/sec
Temperature
Operating: -10 C to +50 C; Storage: -40 C to +60 C
Humidity
0 % to 90 % to 35 C; 75 % to 40 C; 45 % to 50 C
Temperature coefficient
0.1 x (specified accuracy/C) (< 18 C or > 28 C)
Operating altitude
2,000 meters
Battery
9 Volt Alkaline, NEDA 1604A/IEC 6LR61
Battery life
Alkaline: 400 hours typical, without backlight
Safety compliances
ANSI/ISA 82.02.01 (61010-1) 2004, CAN/CSA C22.2 No 61010-1-04, UL 6101B (2003) and IEC/EN
61010-1 2nd Edition for measurement Category III, 600 V, Pollution Degree 2, EMC EN61326-1
Certifications
UL, CSA, TUV, N10140 , VDE
IP rating (dust and water protection)
IP42
N10140
Accuracy specifications (all models)
Accuracy ([% of Reading]
+ [Counts])
Model
0.1 mV
0.5 % + 2
114, 115, 116, 117
0.001 V
0.01 V
0.1 V
0.5 % + 2
114, 115, 116, 117
Function
Range
Resolution
DC millivolts
600.0 mV
DC volts
6.000 V
60.00 V
600.0 V
DC, 45 Hz to
500 Hz
Auto-V LoZ true-rms
1
600.0 V
0.1 V
500 Hz to 1 kHz
2.0 % + 3
4.0 % + 3
45 Hz to 500 Hz
500 Hz to 1 kHz
114, 116, 117
AC millivolts1 true-rms
600.0 mV
0.1 mV
1.0 % + 3
2.0 % + 3
114, 115, 116, 117
AC volts1 true-rms
6.000 V
60.00 V
600.0 V
0.001 V
0.01 V
0.1 V
1.0 % + 3
2.0 % + 3
114, 115, 116, 117
Continuity
600
Ohms
600.0
6.000 k
60.00 k
600.0 k
6.000 M
40.00 M
Diode test
Capacitance
LoZ capacitance (power-up option)
1 nF to 500 F
Beeper on < 20 , off > 250 ;
detects opens or shorts of
500 s or longer
114, 115, 116, 117
0.1
0.001 k
0.01 k
0.1 k
0.001 M
0.01 M
0.9 % + 2
0.9 % + 1
0.9 % + 1
0.9 % + 1
0.9 % + 1
1.5 % + 2
114, 115, 116, 117
2.000 V
0.001 V
0.9 % + 2
115, 116, 117
1000 nF
10.00 F
100.0 F
9999 F
1 nF
0.01 F
0.1 F
1 F
1.9 % + 2
1.9 % + 2
1.9 % + 2
100 F to 1000 F: 1.9 % + 2
> 1000 F: 5 % + 20
115, 116, 117
10 % + 2 typical
115, 116, 117
All ac ranges except Auto-V LoZ are specified from 1 % to 100 % of range. Auto-V LoZ is specified from 0.0 V. Because inputs below 1 % of
range are not specified, it is normal for this and other true-rms meters to display non-zero readings when the test leads are disconnected from
a circuit or are shorted together. For volts, crest factor of 3 at 4000 counts, decreasing linearly to 1.5 at full scale. For amps, crest factor of 3.
AC volts is ac-coupled. Auto-V LoZ, ac mV, and ac amps are dc-coupled.
Accuracy specifications (all models) cont.
Accuracy ([% of Reading]
+ [Counts])
Model
0.1 C
0.2 F
1 % + 102
1 % + 182
116
6.000 A
10.00 A
20 A overload for
30 seconds maximum
0.001 A
0.01 A
1.5 % + 3
115, 117
AC Amps true-rms1 (45 Hz to 1 kHz)
600.0 A
0.1 A
1.5 % + 3 (2.5 % + 3 > 500 Hz)
116
DC amps
6.000 A
10.00 A
20 A overload for
30 seconds maximum
0.001 A
0.01 A
1.0 % + 3
115, 117
DC Amps true-rms
600.0 A
0.1 A
1.0 % + 2
116
Hz (V or A input)2
99.99 Hz
999.9 Hz
9.999 kHz
50.00 kHz
0.01 Hz
0.1 Hz
0.001 kHz
0.01 kHz
0.1 % + 2
115, 117
99.99 Hz
999.9 Hz
9.999 kHz
50.00 kHz
0.01 Hz
0.1 Hz
0.001 kHz
0.01 kHz
0.1 % + 2
116
Function
Range
Resolution
Temperature (K-Type thermocouple)
-40 C to 400 C
-40 F to 752 F
AC amps true-rms1 (45 Hz to 500 Hz)
Hz (V input)3
All ac ranges except Auto-V LoZ are specified from 1 % to 100 % of range. Auto-V LoZ is specified from 0.0 V. Because inputs below 1 % of range
are not specified, it is normal for this and other true-rms meters to display non-zero readings when the test leads are disconnected from a circuit
or are shorted together. For volts, crest factor of 3 at 4000 counts, decreasing linearly to 1.5 at full scale. For amps, crest factor of 3. AC volts is
ac-coupled. Auto-V LoZ, ac mV, and ac amps are dc-coupled.
2
AC Volts Hz is ac-coupled and specified from 5 Hz to 50 kHz. AC Amps Hz is dc-coupled and specified from 45 Hz to 5 kHz. Amps input burden
voltage (typical): 6 A input 2 mV/A, 10 A input 37 mV/A.
3
Frequency is ac-coupled, 45 Hz to 50 kHz.
1
Frequency counter sensitivity (models 115, 116, 117)
Typical sensitivity (rms sine wave)
Input range
Volts AC
AC Amps
(115, 117 only)
5 Hz to 45 Hz
45 Hz to 5 kHz
5 kHz to 10 kHz
10 kHz to 50 kHz
6V
60 V
600 V
0.2 V
2V
20 V
0.2 V to 0.3 V
2 V to 3 V
20 V to 30 V
0.3 V to 0.4 V
3 V to 4 V
30 V to 40 V
0.4 V to 1.0 V
4 V to 10 V
40 V to 100 V
6A
10 A
N/A
N/A
0.4 A
0.5 A
N/A
N/A
N/A
N/A
Input characteristics (all models)
Function
Input impedance
(nominal)
Common mode rejection ratio(1 k unbalanced)
Volts AC
> 5 M < 100 pF
> 60 dB at dc, 50 or 60 Hz
Volts DC
> 10 M < 100 pF
> 100 dB at dc, 50 or 60 Hz
~3 k < 500 pF
> 60 dB at dc, 50 or 60 Hz
Auto-V LoZ
Open circuit test voltage
Ohms
< 2.7 V dc
Diode Test
< 2.7 V dc
Full scale voltage
Normal mode rejection
> 60 dB at 50 or 60 Hz
Short circuit current
To 6.0 M
40 M
< 0.7 V dc
< 0.9 V dc
2.000 V dc
Fluke. Keeping your world
up and running.
Fluke Corporation
PO Box 9090, Everett, WA USA 98206
Fluke Europe B.V.
PO Box 1186, 5602 BD
Eindhoven, The Netherlands
< 350 A
< 1.2 mA
For more information call:
In the U.S.A. (800) 443-5853 or
Fax (425) 446-5116
In Europe/M-East/Africa +31 (0) 40 2675 200 or
Fax +31 (0) 40 2675 222
In Canada (800)-36-FLUKE or
Fax (905) 890-6866
From other countries +1 (425) 446-5500 or
Fax +1 (425) 446-5116
Web access: http://www.fluke.com
2006 Fluke Corporation. All rights reserved.
Printed in U.S.A. 11/2006 2793260 D-EN-N Rev A
Fluke Corporation
Fluke 11X Series Digital Multimeters Extended Specifications
