Manual Supplement
2009-2013 Fluke Corporation. All rights reserved.
Manual Title: 114,115, 116, and 117 Calibration Supplement Issue: 5
Print Date: September 2006 Issue Date: 4/13
Revision/Date: 1, 10/08 Page Count: 3
This supplement contains information necessary to ensure the
accuracy of the above manual.
114, 115, 116, and 117 Calibration Information Manual Supplement
11/09 1
Change #1
On page 10, delete step 30.
Change #2
On page 4, replace Table 2 with the following:
Table 2. Accuracy Specifications
Function Range Resolution
Accuracy
([% of Reading] + [Counts])
Model
[1]
DC millivolts 600.0 mV 0.1 mV 0.5 % + 2 114, 115, 116, 117
DC Volts
6.000 V
60.00 V
600.0 V
0.001 V
0.01 V
0.1 V
0.5 % + 2 114, 115, 116, 117
DC, 45 to 500 Hz 500 Hz to 1 kHz
Auto-V LoZ
[2]
True-rms 600.0 V 0.1 V 2.0 % + 3 4.0 % + 3 114, 116, 117
45 to 500 Hz 500 Hz to 1 kHz
AC millivolts
[2]
True-rms 600.0 mV 0.1 mV 1.0 % + 3 2.0 % + 3 114, 115, 116, 117
AC Volts
[2]
True-rms
6.000 V
60.00 V
600.0 V
0.001 V
0.01 V
0.1 V
1.0 % + 3 2.0 % + 3 114, 115, 116, 117
Continuity 600 1
Beeper on <20 , off >250 ; detects opens
or shorts of 500 s or longer.
114, 115, 116, 117
Ohms
600.0
6.000 k
60.00 k
600.0 k
6.000 M
40.00 M
0.1
0.001 k
0.01 k
0.1 k
0.001 M
0.01 M
0.9 % + 2
0.9 % + 1
0.9 % + 1
0.9 % + 1
0.9 % + 1
5.0 % + 2
114, 115, 116, 117
Diode test 2.000 V 0.001 V 0.9 % + 2 115, 116, 117
Capacitance 1000 nF
10.00 F
100.0 F
9999 F
1 nF
0.01 F
0.1 F
1 F
1.9 % + 2
1.9 % + 2
1.9 % + 2
100 F - 1000 F: 1.9 % + 2
>1000 F: 5 % + 20
115, 116, 117
Lo-Z Capacitance
(Power-up option)
1 nF to 500 F 10 % +2 typical
115, 116, 117
AC Amps True-rms
[2]
(45 Hz to 500 Hz)
6.000 A
10.00 A
[4]
20 A overload for 30
seconds maximum, 10
minutes rest minimum.
0.001 A
0.01 A
1.5 % + 3 115, 117
DC Amps
6.000 A
10.00 A
[4]
20 A overload for 30
seconds maximum, 10
minutes rest minimum.
0.001 A
0.01 A
1.0 % + 3 115, 117
Manual Supplement 114, 115, 116, and 117 Calibration Information
2 4/13
Temperature (Type K
thermocouple)
-40 C to 400 C
-40 F to 752 F
0.1 C
0.2 F
1.0 % + 10
[5]
1.0 % + 18
[5]
116
AC Amps True-rms
[2]
(45 Hz to 1 kHz)
600.0 A 0.1 A
1.5 % + 3 (2.5 % + 3 > 500 Hz) 116
DC Amps 600.0 A 0.1 A 1.0 % + 2 116
Hz (V or A input)
[3]
99.99 Hz
999.9 Hz
9.999 kHz
50.00 kHz
0.01 Hz
0.1 Hz
0.001 kHz
0.01 kHz
0.1 % + 2 115, 116, 117
Notes:
[1] Models listed in this column also refer to the C version of the model. For example, those rows containing model 115 are applicable to the 115C
as well.
[2] All ac ranges except Auto-V LoZ are specified from 1 % to 100% of range. Auto-V LoZ is specified from 0.0 V. Because inputs below 1 % of range
are not specified, it is normal for this and other true-rms meters to display non-zero readings when the test leads are disconnected from a circuit
or are shorted together. For volts, crest factor of 3 at 4000 counts, decreasing linearly to 1.5 at full scale. For amps, crest factor of 3. AC volts is
ac-coupled. Auto-V LoZ, AC mV, AC amps, and AC amps are dc-coupled.
[3] AC Volts Hz is ac-coupled and specified from 5 Hz to 50 kHz. AC amps Hz is dc-coupled and specified from 45 Hz to 5 kHz.
[4] >10 A unspecified.
[5] Temperature uncertainty (accuracy) does not include the error of the thermocouple probe.
Change #3
On page 2, under Safety Information:
Change: Do not use the Meter around explosive gas or vapor.
To: Do not use the Product around explosive gas, vapor, or in damp or wet environments
Change #4, 63151, 63405
On page 3, replace Table 1 with:
Table 1. Electrical Symbols
Symbol Description Symbol Description
AC (Alternating Current) = Fuse
DC (Direct Current) _ Double Insulated
@ Hazardous voltage Important Information; Refer to manual
Battery (Low battery when shown on the
display.)
} Earth ground
_ Do not dispose of this product as unsorted municipal waste. Go to Flukes website for recycling information.
@ Conforms to relevant South Korean EMC Standards
CAT II
Measurement Category II is applicable to test and measuring circuits connected directly to utilization points
(socket outlets and similar points) of the low-voltage MAINS installation.
CAT III
Measurement Category III is applicable to test and measuring circuits connected to the distribution part of
the buildings low-voltage MAINS installation.
CAT IV
Measurement Category IV is applicable to test and measuring circuits connected at the source of the
buildings low-voltage MAINS installation.
114, 115, 116, and 117 Calibration Information Manual Supplement
4/13 3
On page 3, under General Specifications, delete Surge Protection, Safety Compliance and
Certifications and add:
Safety ............................................................. IEC 61010-1: 600 V CAT III, Pollution Degree 2
Electromagnetic Environment ..................... IEC 61326-1: Portable
Electromagnetic Compatibility .................... Applies to use in Korea only:
Class A Equipment (Industrial Broadcasting & Communication
Equipment)
[1]
[1] This product meets requirements for industrial (Class A)
electromagnetic wave equipment and the seller or user should
take notice of it. This equipment is intended for use in business
environments and is not to be used in homes.
