721F XT/XR WHEEL LOADER

TIER 4 FINAL CERTIFIED

ENGINE ENGINE (cont.) DRIVETRAIN (cont.)

Make FPT Torque peak: Travel speeds 5-speed transmission:

Model F4HFE613T Maximum Power Mode: Forward Reverse
Gross @ 1300 RPM 701 lbft (950 Nm) mph (kph) mph (kph)
Emissions Certification Tier 4 Final Net @ 1300 RPM 674 lbft (914 Nm) 1st 4.5 (7.2) 4.9 (7.9)
Type 4-stroke, turbocharged Standard Power Mode: 2nd 7.8 (12.6) 8.4 (13.5)
and air-to-air cooled Gross @ 1300 RPM 620 lbft (841 Nm) 3rd 11.8 (19.0) 19.3 (31.1)
Cylinders 6-cylinder in-line Net @ 1300 RPM 594 lbft (805 Nm) 4th 18.3 (29.5)
Economy Power Mode: 5th 24.8 (40.0)
Bore/Stroke 4.09 x 5.20 in
Gross @ 1200 RPM 589 lbft (799 Nm) NOTE: Travel speeds at full engine throttle
(104 x 132 mm)
Net @ 1200 RPM 566 lbft (768 Nm) w/ 23.5 x 25 L3 tires.
Displacement 411 in (6.7 L)
3
Torque rise:
Fuel #2 Diesel, #1 and #2 mixture Maximum power range 37%
permitted for cold temperature ELECTRICAL
NOTE: Gross horsepower and torque per SAE J1995.
Fuel injection Direct injection electronic Net horsepower and torque per SAE J1349. Voltage 24 Volts, negative ground
Fuel filter Replaceable Alternator 120 amp
Fuel pump Bosch CR / CP3 DRIVETRAIN Batteries (2) 12-volt
Gradeability: Transmission:
Side-to-side 35 4F / 3R Proportional w/ Electronic Control OPERATOR ENVIRONMENT
Fore and aft 35 Module torque sensing autoshift/ manual
ROPS/FOPS Cab w/ heat and AC; Key start;
Air filter Dry type elements shift and modulation
Articulated power steering w/ tilt column; Fully
w/ warning restriction indicator Gears Helical cut adjustable suspension seat; Foot throttle;
Mid-mount cooling module: Torque converter: 1-Lever loader control w/ wrist rest; Cup
Mid-mount air/water Stall ratio 4-speed 2.81:1 holder; Coat hook; 1 Interior rearview mirror;
Fan hydraulic driven: Stall ratio 5-speed 2.42:1 2 in. (51 mm) retractable seat belt; Storage tray
Style 8 blade puller behind seat; Lunch box compartment; Single
Differential Limited slip w/ 30% transfer
Diameter 32 in (813 mm) brake pedal; F-N-R shuttle switch; Glove box;
on front and rear axles
Pressurized air filtering; Anti-glare window
Water pump Integral Rear axle oscillation 24 total strip; Defroster; Side window partial/fully open;
Engine oil pump operating angles ratings: Front axles: Dome light; Wipers, rear and intermittent front;
Side-to-side 35 Differential ratio 3.4 Windshield washers, front and rear; Rubber floor
Fore and aft 35 Planetary ratio 6.0 mat; Horn.
Oil filtration Replaceable Final axle ratio 20.2 Displays/ Gauges:
Engine speeds RPM Rear axles: Analog:
Rated full load 2000 Differential ratio 3.2 Transmission oil temperature; Hydraulic
Horsepower: Planetary ratio 6.4 oil temperature; Fuel Level; Engine coolant
Maximum Power Mode: Final axle ratio 20.4 temperature.
Peak gross @ 2000 RPM 194 hp (145 kW) Heavy-duty axles optional: LCD screen:
Net rated @ 2000 RPM 178 hp (133 kW) Front axle equipped w/ locking differential Hour meter; Engine speed; Travel speed;
Peak net @ 2000 RPM 178 hp (133 kW) Rear axle equipped w/ open differential Time; Automatic transmission indication;
Standard Power Mode: Current gear selection; FNR indication;
Planetaries Outboard DeClutch indication; Engine mode
Peak gross @ 1700 RPM 176 hp (131 kW)
Net rated @ 2000 RPM 143 hp (107 kW) Service brakes: indication; Trip computer; Fuel
Peak net @ 1600 RPM 162 hp (121 kW) Hydraulically actuated, maintenance-free, consumption; Multiple languages,
Economy Power Mode: multiple wet disc w/ accumulator to all Metric/English; Engine diagnostics;
Peak gross @ 1400 RPM 146 hp (109 kW four wheels Transmission diagnostics; Warning
Net rated @ 2000 RPM 121 hp (90 kW) Brake surface area: prompts; Error reporting; DEF gauge;
Peak net @ 1400 RPM 138 hp (103 kW) Front hub each 600 in2 (0.387 m2) Diff. lock*.
NOTE: Gross horsepower and torque per SAE J1995. Rear hub each 600 in2 (0.387 m2) Audible/ Visual alarms:
Net horsepower and torque per SAE J1349. Parking brakes: Warning lights:
Spring-applied hydraulic release disc on Four-way flashers and turn signals; Brake
transmission output shaft neutralizes power pressure; Lamp/high beam indication; Grid
flow to wheels when engaged heater*.
Travel speeds 4-speed transmission: NOTE: *If equipped w/ option.
Forward Reverse
mph (kph) mph (kph)
1st 4.7 (7.6) 5.0 (8.0)
2nd 7.9 (12.8) 8.3 (13.4)
3rd 15.2 (24.5) 16.0 (25.7)
4th 23.5 (37.8)
NOTE: Travel speeds at full engine throttle
w/ 23.5 x 25 L3 tires.
Page 1 of 10
OPERATOR ENVIRONMENT (cont.) HYDRAULICS OTHER SPECIFICATIONS
Audible/Visual alarms: Pump steering/ implement: Lift cylinder:
Caution alarm: Closed center pressure / flow compensated Bore diameter 4.7 in (121 mm)
Parking brake; Coolant temperature; Variable displacement load-sensing: Rod diameter 3.0 in (76 mm)
Hydraulic oil temperature; Transmission 31.7 gpm @ 2000 RPM Stroke 32.6 in (828 mm)
oil temperature; Air filter; Transmission (120 L / min @ 2000 RPM) Dump cylinder Z-Bar and XR:
filter; Hydraulic filter; Alternator; Low fuel. Bore diameter 5.7 in (146 mm)
Critical alarm: Loader control valve:
Closed-center, sectional 2, 3 or 4-function Rod diameter 3.0 in (76 mm)
Engine oil pressure; Brake pressure; Stroke 24.8 in (629 mm)
Steering pressure w/ aux. steering*; w/ pilot control for lift, tilt and auxiliary
Coolant temperature; Hydraulic oil hydraulics, electromagnetic detents in float, Dump cylinder XT:
temperature; Transmission oil temperature. raise and rollback Bore diameter 4.5 in (114 mm)
Backup alarm Loader auxiliary steering: Rod diameter 2.3 in (57 mm)
Hydraulic orbital center-pivot articulating Stroke 33.7 in (857 mm)
NOTE: *If equipped w/ option.
w/ on-demand oil flow Loader:
High pressure standby: Z-Bar loader linkage; Single control for
OPERATING WEIGHT Implement 3,625 psi (25 000 kPa) lift and tilt; Positive hold float; Automatic
Z-Bar Steering 3,499 psi (24 132 kPa) return-to-dig; Automatic height control;
Automatic return-to-travel; Brake pedal
Unit equipped w/ 3.25 yd (2.5 m3) MD pin on w/ Filtration: transmission disconnect; Bucket position
bolt on edge; 20.5R25 XHA Michelin tires; ROPS Filtered vent w/ relief on hydraulic reservoir, indicator on bucket.
cab w/ heater and A/C; Std. battery; Heavy maintains 3-5 psi on reservoir, 10-micron,
counterweight 2,764 lb (1 254 kg); Front and returns filter furnishes only clean oil to all Cycle time:
rear fenders; Lights; Full fuel/urea; 175 lb (79 kg) components of the system Raise w/ rated bucket load:
operator: Z-Bar 5.2 sec
31,508 lb (14 292 kg) XR 5.2 sec
SERVICE CAPACITIES XT 5.2 sec
XT Dump w/ rated bucket load:
Fuel tank 65.0 gal (246.0 L)
Unit equipped w/ 3.0 yd (2.3 m3) CNH GP w/ Z-Bar 1.2 sec
BOE and CNH coupler; 20.5R25 XHA Michelin DEF tank Diesel Exhaust Fluid: XR 1.2 sec
tires; ROPS cab w/ heater and A/ C; Std. Usable capacity 9.8 gal (37.1 L) XT 1.3 sec
battery; Heavy counterweight 2,764 lb Total 15.6 gal (58.9 L) Power down:
(1 254 kg); Front and rear fenders; Lights; Hydraulic system: Z-Bar 2.5 sec
Full fuel/urea; 175 lb (79 kg) operator: Reservoir 24.0 gal (90.8 L) XR 2.5 sec
32,567 lb (14 772 kg) Total 47.0 gal (177.8 L) XT 2.5 sec
XR Transmission: Float down:
Service w/ filter 9.0 gal (34.0 L) Z-Bar 2.4 sec
Unit equipped w/ 3.0 yd3 (2.3 m3) pin on bucket
XR 2.4 sec
w/ bolt on edge; 20.5R25 XHA Michelin tires; Front and rear axle:
XT 2.4 sec
ROPS cab w/ heater and A/C; Std. battery; Front axle 9.2 gal (35.0 L)
Heavy counterweight 2,764 lb (1 254 kg); Front Rear axle 6.1 gal (23.0 L)
and rear fenders; Lights; Full fuel/ urea; 175 lb Front and rear axle optional:
(79 kg) operator: Front axle 9.2 gal (35.0 L)
32,064 lb (14 544 kg) Rear axle 9.2 gal (35.0 L)
Engine oil w/ filter 4.0 gal (15.1 L)
Cooling system 7.5 gal (28.4 L)

721F Page 2 of 10
 E
J
F
K

A
H

B L
G
Line drawings are for illustrative purpose only and may not be exact representation of unit.

DIMENSIONS
A. Height to top of ROPS cab 133.3 in (3 385 mm)
Height to drawbar 43.8 in (1 112 mm)
B. Wheelbase 128.1 in (3 253 mm)
C. Ground clearance 14.4 in (365 mm)
D. Angle of departure 32
Width:
Overall* without bucket 104.4 in (2 653 mm)
Centerline tread 79.9 in (2 030 mm)
Turning radius* outside 226.4 in (5 750 mm)
Turning angle:
From center 40
Total angle 80
Rear axle oscillation, total 24
NOTE: *Dimensions taken with 23.5R25 Michelin XHA2 tires. Additional dimensions on pages 4 through 8.

WEIGHT ADJUSTMENTS
Tipping Load Tipping Load
Weight Adjustment Adjustment
Select Options Adjustment Straight 40 Turn
20.5 x 25 12 ply L2 Goodyear -556 lb (-252 kg) -437 lb (-198 kg) -386 lb (-175 kg)
20.5 x 25 12 ply L3 Goodyear -227 lb (-103 kg) -179 lb (-81 kg) -159 lb (-72 kg)
20.5 R25 XTLA Michelin tires -379 lb (-172 kg) -298 lb (-135 kg) -262 lb (-119 kg)
20.5 R25 RT-3B Goodyear 152 lb (69 kg) 117 lb (53 kg) 104 lb (47 kg)
Base Counterweight -529 lb (-240 kg) -1,208 lb (-548 kg) -1,023 lb (-464 kg)
ROPS Canopy -295 lb (-134 kg) -340 lb (-154 kg) -313 lb (-142 kg)
NOTE: Unit equipped with Z-Bar loader arms, 4.75 yd3 (3.6 m3) pin on bucket with bolt-on edge, 23.5R25 Michelin XHA2 tires, ROPS cab with heater and air conditioner, full
counterweight, heavy-duty batteries, front and rear fenders, full fuel and 175 lb (79 kg) operator. Adjust select options from rated weight.

721F Page 3 of 10
PERFORMANCE DATA
721F Z-Bar* 3.0 yd3 HD Pin On (2.3 m3) 3.0 yd3 HD Pin On (2.3 m3) 3.25 yd3 MD Pin On (2.5 m3)
Bucket with Bolt-on Edge Bucket with Teeth Only Bucket with Bolt-on Edge
SAE bucket capacity struck 2.5 yd3 (1.94 m3) 2.4 yd3 (1.85 m3) 2.8 yd3 (2.11 m3)
Heaped 3.0 yd3 (2.30 m3) 2.8 yd3 (2.13 m3) 3.3 yd3 (2.49 m3)
Bucket width outside 106.3 in (2 700 mm) 107.6 in (2 732 mm) 106.3 in (2 700 mm)
Bucket weight 2,506 lb (1 137 kg) 2,605 lb (1 182 kg) 2,614 lb (1 186 kg)
E. Operating height fully raised with spillguard 203.5 in (5 169 mm) 203.5 in (5 169 mm) 205.9 in (5 229 mm)
F. Hinge pin height fully raised 156.7 in (3 979 mm) 156.7 in (3 979 mm) 156.7 in (3 979 mm)
G. Overall length bucket level on ground 299.1 in (7 596 mm) 305.0 in (7 748 mm) 301.1 in (7 648 mm)
Dump angle fully raised 55 55 55
H. Dump height fully raised, 45 dump 116.7 in (2 963 mm) 112.8 in (2 864 mm) 115.4 in (2 930 mm)
J. Bucket reach fully raised, 45 dump 42.8 in (1 086 mm) 47.1 in (1 196 mm) 44.3 in (1 125 mm)
K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 64.3 in (1 633 mm) 66.9 in (1 698 mm) 65.3 in (1 658 mm)
Operating load ISO 11,687 lb (5 301 kg) 11,777 lb (5 342 kg) 11,607 lb (5 265 kg)
Operating load SAE 10,609 lb (4 812 kg) 10,745 lb (4 874 kg) 10,524 lb (4 774 kg)
Maximum material density ISO 3,883 lb / yd (2 304 kg / m )
3 3
4,229 lb / yd (2 509 kg / m )
3 3
3,570 lb/yd3 (2 118 kg/m3)
Maximum material density SAE 3,524 lb / yd (2 091 kg / m )
3 3
3,836 lb / yd (2 276 kg / m )
3 3
3,236 lb/yd3 (1 920 kg/m3)
Tipping load ISO:
Straight 26,696 lb (12 109 kg) 26,918 lb (12 210 kg) 26,530 lb (12 034 kg)
40 turn 23,371 lb (10 601 kg) 23,556 lb (10,685 kg) 23,212 lb (10 529 kg)
Tipping load SAE:
Straight 25,022 lb (11 350 kg) 25,219 lb (11 439 kg) 24,846 lb (11 270 kg)
40 turn 21,219 lb (9 625 kg) 21,372 lb (9 694 kg) 21,048 lb (9 547 kg)
Lift capacity:
Full height 16,288 lb (7 388 kg) 16,193 lb (7 345 kg) 16,180 lb (7 339 kg)
Maximum reach 22,518 lb (10 214 kg) 22,443 lb (10 180 kg) 22,406 lb (10 163 kg)
Ground 29,921 lb (13 572 kg) 30,091 lb (13 649 kg) 29,690 lb (13 467 kg)
Breakout force with tilt cylinder 32,906 lb (14 926 kg) 35,598 lb (16 147 kg) 31,383 lb (14 235 kg)
Maximum rollback:
Ground 39 40 39
Carry position 43 43 43
@ Maximum reach 54 54 54
@ Full height 57 57 57
L. Dig depth 2.9 in (73 mm) 3.1 in (78 mm) 2.9 in (73 mm)
Maximum grading angle with bucket back dragging 60 61 60
Loader clearance circle with bucket 496.3 in (12 607 mm) 500.9 in (12 724 mm) 497.5 in (12 636 mm)

721F XR 3.0 yd3 HD Pin On (2.3 m3) 3.0 yd3 HD Pin On (2.3 m3) 3.25 yd3 MD Pin On (2.5 m3)
Bucket with Bolt-on Edge Bucket with Teeth Only Bucket with Bolt-on Edge
E. Operating height fully raised with spillguard 219.1 in (5 564 mm) 219.0 in (5 563 mm) 221.4 in (5 623 mm)
F. Hinge pin height fully raised 172.2 in (4 374 mm) 172.2 in (4 374 mm) 172.2 in (4 374 mm)
G. Overall length bucket level on ground 313.2 in (7 955 mm) 319.1 in (8 106 mm) 315.2 in (8 006 mm)
Dump angle fully raised 55 55 55
H. Dump height fully raised, 45 dump 132.2 in (3 358 mm) 128.3 in (3 259 mm) 130.9 in (3 324 mm)
J. Bucket reach fully raised, 45 dump 42.8 in (1 087 mm) 47.1 in (1 197 mm) 44.3 in (1 126 mm)
K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 76.5 in (1 942 mm) 79.2 in (2 012 mm) 77.5 in (1 968 mm)
Operating load ISO 9,784 lb (4 438 kg) 9,841 lb (4 464 kg) 9,709 lb (4 404 kg)
Operating load SAE 8,960 lb (4 064 kg) 9,006 lb (4 085 kg) 8,878 lb (4 027 kg)
Maximum material density ISO 3,251 lb / yd3 (1 929 kg / m3) 3,533 lb / yd3 (2 096 kg / m3) 2,987 lb/yd3 (1 772 kg/m3)
Maximum material density SAE 2,977 lb / yd3 (1 766 kg / m3) 3,233 lb / yd3 (1 980 kg / m3) 2,731 lb/yd3 (1 620 kg/m3)
Tipping load ISO:
Straight 22,474 lb (10 194 kg) 22,617 lb (10 259 kg) 22,315 lb (10 122 kg)
40 turn 19,568 lb (8 876 kg) 19,683 lb (8 928 kg) 19,418 lb (8 808 kg)
Tipping load SAE:
Straight 21,222 lb (9 626 kg) 21,347 lb (9 683 kg) 21,056 lb (9 551 kg)
40 turn 17,917 lb (8 127 kg) 18,012 lb (8 170 kg) 17,758 lb (8 055 kg)
Lift capacity:
Full height 15,181 lb (6 886 kg) 15,084 lb (6 842 kg) 15,073 lb (6 837 kg)
Maximum reach 20,201 lb (9 163 kg) 20,122 lb (9 127 kg) 20,086 lb (9 111 kg)
Ground 24,934 lb (11 310 kg) 25,033 lb (11 355 kg) 24,727 lb (11 216 kg)
Breakout force with tilt cylinder 32,732 lb (14 847 kg) 35,415 lb (16 064 kg) 31,215 lb (14 159 kg)
Loader clearance circle with bucket 508.7 in (12 922 mm) 513.9 in (13 052 mm) 510.1 in (12 956 mm)

721F Page 4 of 10
PERFORMANCE DATA
721F Z-Bar* 3.25 yd3 MD Pin On (2.5 m3) 3.5 yd3 LD Pin On (2.7 m3) 3.5 yd3 (2.7 m3) Bucket with
Bucket with Teeth Only Bucket with Bolt-on Edge Grapple with Bolt-on Edge
SAE bucket capacity struck 2.6 yd3 (2.00 m3) 3.0 yd3 (2.30 m3) 3.0 yd3 (2.32 m3)
Heaped 3.0 yd3 (2.30 m3) 3.5 yd3 (2.68 m3) 3.5 yd3 (2.67 m3)
Bucket width outside 107.6 in (2 732 mm) 106.3 in (2 700 mm) 106.3 in (2 700 mm)
Bucket weight 2,700 lb (1 225 kg) 2,822 lb (1 280 kg) 4,366 lb (1 981 kg)
E. Operating height fully raised with spillguard 205.8 in (5 228 mm) 208.6 in (5 297 mm) 208.1 in (5 286 mm)
F. Hinge pin height fully raised 156.7 in (3 979 mm) 156.7 in (3 979 mm) 156.6 in (3 977 mm)
G. Overall length bucket level on ground 307.1 in (7 800 mm) 303.5 in (7 708 mm) 303.5 in (7 710 mm)
Dump angle fully raised 55 55 55
H. Dump height fully raised, 45 dump 111.5 in (2 831 mm) 113.8 in (2 891 mm) 113.7 in (2 889 mm)
J. Bucket reach fully raised, 45 dump 48.6 in (1 235 mm) 46.1 in (1 171 mm) 46.1 in (1 171 mm)
K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 67.8 in (1 721 mm) 66.4 in (1 686 mm) 66.3 in (1 685 mm)
Operating load ISO 11,706 lb (5 310 kg) 11,461 lb (5 199 kg) 10,527 lb (4 775 kg)
Operating load SAE 10,606 lb (4 811 kg) 10,375 lb (4 706 kg) 9,436 lb (4 280 kg)
Maximum material density ISO 3,892 lb / yd (2 309 kg / m )
3 3
3,274 lb / yd (1 943 kg / m )
3 3
3,015 lb/yd3 (1 789 kg/m3)
Maximum material density SAE 3,526 lb / yd (2 092 kg / m )
3 3
2,964 lb / yd (1 759 kg / m )
3 3
2,702 lb/yd3 (1 603 kg/m3)
Tipping load ISO:
Straight 26,769 lb (12 142 kg) 26,116 lb (11 896 kg) 24,315 lb (11 029 kg)
40 turn 23,413 lb (10 620 kg) 22,921 lb (10 397 kg) 21,055 lb (9550 kg)
Tipping load SAE:
Straight 25,058 lb (11 366 kg) 24,540 lb (11 131 kg) 22,622 lb (10 261 kg)
40 turn 21,213 lb (9 622 kg) 20,752 lb (9 413 kg) 18,869 lb (8 559 kg)
Lift capacity:
Full height 16,098 lb (7 302 kg) 15,972 lb (7 245 kg) 14,427 lb (6 544 kg)
Maximum reach 22,342 lb (10 134 kg) 22,189 lb (10 065 kg) 20,615 lb (9 351 kg)
Ground 29,872 lb (13 550 kg) 29,337 lb (13 307 kg) 27,315 lb (12 390 kg)
Breakout force with tilt cylinder 33,805 lb (15 344 kg) 29,692 lb (13 486 kg) 27,977 lb (12 690 kg)
Maximum rollback:
Ground 40 39 39
Carry position 43 43 43
@ Maximum reach 54 54 54
@ Full height 57 57 57
L. Dig depth 3.1 in (78 mm) 2.9 in (74 mm) 3.0 in (76 mm)
Maximum grading angle with bucket back dragging 61 60 60
Loader clearance circle with bucket 502.1 in (12 754 mm) 498.9 in (12 671 mm) 498.9 in (12 671 mm)

721F XR 3.25 yd3 MD Pin On (2.5 m3) 3.5 yd3 LD Pin On (2.7 m3) 3.5 yd3 (2.7 m3) Bucket with
Bucket with Teeth Only Bucket with Bolt-on Edge Grapple with Bolt-on Edge
E. Operating height fully raised with spillguard 221.4 in (5 623 mm) 224.1 in (5 692 mm) 223.6 in (5 680 mm)
F. Hinge pin height fully raised 172.2 in (4 374 mm) 172.2 in (4 374 mm) 172.1 in (4 372 mm)
G. Overall length bucket level on ground 321.1 in (8 157 mm) 317.6 in (8 066 mm) 317.6 in (8 068 mm)
Dump angle fully raised 55 55 55
H. Dump height fully raised, 45 dump 127.0 in (3 226 mm) 129.4 in (3 286 mm) 129.3 in (3 284 mm)
J. Bucket reach fully raised, 45 dump 48.7 in (1 236 mm) 46.1 in (1 172 mm) 46.1 in (1 172 mm)
K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 80.2 in (2 037 mm) 78.7 in (1 998 mm) 78.7 in (1 998 mm)
Operating load ISO 9,773 lb (4 433 kg) 9,572 lb (4 342 kg) 8,671 lb (3 933 kg)
Operating load SAE 8,933 lb (4 052 kg) 8,739 lb (3 964 kg) 7,831 lb (3 552 kg)
Maximum material density ISO 3,250 lb / yd3 (1 928 kg / m3) 2,736 lb / yd3 (1 623 kg / m3) 2,483 lb/yd3 (1 473 kg/m3)
Maximum material density SAE 2,969 lb / yd3 (1 762 kg / m3) 2,497 lb / yd3 (1 482 kg / m3) 2,243 lb/yd3 (1 331 kg/m3)
Tipping load ISO:
Straight 22,474 lb (10 194 kg) 22,031 lb (9 993 kg) 20,194 lb (9 160 kg)
40 turn 19,546 lb (8 866 kg) 19,143 lb (8 683 kg) 17,341 lb (7 866 kg)
Tipping load SAE:
Straight 21,197 lb (9 615 kg) 20,770 lb (9 421 kg) 18,922 lb (8 583 kg)
40 turn 17,864 lb (8 103 kg) 17,480 lb (7 929 kg) 15,664 lb (7 105 kg)
Lift capacity:
Full height 14,990 lb (6 799 kg) 14,865 lb (6 743 kg) 13,320 lb (6 042 kg)
Maximum reach 20,022 lb (9 082 kg) 19,870 lb (9 013 kg) 18,922 lb (8 300 kg)
Ground 24,839 lb (11 267 kg) 24,405 lb (11 070 kg) 22,478 lb (10 196 kg)
Breakout force with tilt cylinder 33,653 lb (15 265 kg) 29,573 lb (13 414 kg) 27,820 lb (12 619 kg)
Loader clearance circle with bucket 515.2 in (13 087 mm) 511.7 in (12 996 mm) 511.7 in (12 996 mm)

721F Page 5 of 10
PERFORMANCE DATA
721F Z-Bar* 5.5 yd3 LD Pin On (4.2 m3) 3.0 yd3 GP (2.3 m3) Bucket 3.0 yd3 GP (2.3 m3) Bucket
Bucket with Bolt-on Edge on CNH Z-Bar Coupler on CNH Z-Bar Coupler
with Bolt-on Edge with Teeth Only
SAE bucket capacity struck 5.5 yd3 (4.20 m3) 2.5 yd3 (1.92 m3) 2.4 yd3 (1.85 m3)
Heaped 5.5 yd3 (4.20 m3) 2.9 yd3 (2.25 m3) 2.8 yd3 (2.13 m3)
Bucket width outside 106.3 in (2 700 mm) 106.3 in (2 700 mm) 107.6 in (2 732 mm)
Bucket weight 3,025 lb (1 372 kg) 3,721 lb (1 688 kg) 3,559 lb (1 614 kg)
E. Operating height fully raised with spillguard 223.2 in (5 669 mm) 211.0 in (5 359 mm) 211.0 in (5 360 mm)
F. Hinge pin height fully raised 156.7 in (3 979 mm) 156.6 in (3 978 mm) 156.6 in (3 978 mm)
G. Overall length bucket level on ground 319.6 in (8 119 mm) 309.8 in (7 868 mm) 315.7 in (8 020 mm)
Dump angle fully raised 55 55 55
H. Dump height fully raised, 45 dump 103.0 in (2 617 mm) 109.7 in (2 787 mm) 105.9 in (2 689 mm)
J. Bucket reach fully raised, 45 dump 56.7 in (1 441 mm) 50.9 in (1 293 mm) 55.2 in (1 403 mm)
K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 71.3 in (1 811 mm) 69.2 in (1 757 mm) 71.4 in (1 814 mm)
Operating load ISO 10,754 lb (4 878 kg) 10,185 lb (4 620 kg) 10,379 lb (4 708 kg)
Operating load SAE 9,711 lb (4 405 kg) 9,217 lb (4 181 kg) 9,396 lb (4 262 kg)
Maximum material density ISO 1,959 lb / yd3 (1 162 kg / m3) 3,462 lb / yd3 (2 054 kg / m3) 3,727 lb/yd3 (2 211 kg/m3)
Maximum material density SAE 1,768 lb / yd3 (1 049 kg / m3) 3,132 lb / yd3 (1 858 kg / m3) 3,373 lb/yd3 (2 001 kg/m3)
Tipping load ISO:
Straight 24,652 lb (11 182 kg) 23,444 lb (10 634 kg) 23,861 lb (10 823 kg)
40 turn 21,506 lb (9 755 kg) 20,371 lb (9 240 kg) 20,759 lb (9 416 kg)
Tipping load SAE:
Straight 23,040 lb (10 451 kg) 21,954 lb (9 958 kg) 22,346 lb (10 136 kg)
40 turn 19,422 lb (8 810 kg) 18,433 lb (8 361 kg) 18,792 lb (8 524 kg)
Lift capacity:
Full height 15,759 lb (7 148 kg) 15,005 lb (6 806 kg) 15,173 lb (6 882 kg)
Maximum reach 21,879 lb (9 924 kg) 21,060 lb (9 552 kg) 21,248 lb (9 638 kg)
Ground 27,959 lb (12 682 kg) 26,962 lb (12 230 kg) 27,342 lb (12 402 kg)
Breakout force with tilt cylinder 22,293 lb (10 112 kg) 26,375 lb (11 964 kg) 28,237 lb (12 808 kg)
Maximum rollback:
Ground 40 39 39
Carry position 43 43 43
@ Maximum reach 54 54 54
@ Full height 57 57 57
L. Dig depth 4.3 in (110 mm) 3.0 in (75 mm) 3.1 in (80 mm)
Maximum grading angle with bucket back dragging 65 60 62
Loader clearance circle with bucket 508.8 in (12 923 mm) 502.8 in (12 770 mm) 507.6 in (12 893 mm)

721F XR 5.5 yd3 LD Pin On (4.2 m3) 3.0 yd3 GP (2.3 m3) Bucket 3.0 yd3 GP (2.3 m3) Bucket
Bucket with Bolt-on Edge on Z-Bar Coupler on Z-Bar Coupler
with Bolt-on Edge with Teeth Only
E. Operating height fully raised with spillguard 238.7 in (6 064 mm) 226.5 in (5 754 mm) 226.5 in (5 754 mm)
F. Hinge pin height fully raised 172.2 in (4 373 mm) 172.1 in (4 372 mm) 172.2 in (4 373 mm)
G. Overall length bucket level on ground 333.6 in (8 473 mm) 323.9 in (8 226 mm) 329.8 in (8 377 mm)
Dump angle fully raised 55 55 55
H. Dump height fully raised, 45 dump 118.6 in (3 012 mm) 125.3 in (3 182 mm) 121.4 in (3 083 mm)
J. Bucket reach fully raised, 45 dump 56.8 in (1 442 mm) 50.9 in (1 294 mm) 55.3 in (1 404 mm)
K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 84.3 in (2 140 mm) 81.7 in (2 075 mm) 84.2 in (2 138 mm)
Operating load ISO 9,001 lb (4 083 kg) 8,494 lb (3 853 kg) 8,662 lb (3 929 kg)
Operating load SAE 8,197 lb (3 718 kg) 7,743 lb (3 512 kg) 7,901 lb (1 845 kg)
Maximum material density ISO 1,638 lb / yd3 (972 kg / m3) 2,887 lb / yd3 (1 713 kg / m3) 3,110 lb/yd3 (1 845 kg/m3)
Maximum material density SAE 1,492 lb / yd3 (885 kg / m3) 2,631 lb / yd3 (1 561 kg / m3) 2,836 lb/yd3 (1 683 kg/m3)
Tipping load ISO:
Straight 20,765 lb (9 419 kg) 19,695 lb (8 933 kg) 20,051 lb (9 095 kg)
40 turn 18,005 lb (8 167 kg) 16,991 lb (7 707 kg) 17,324 lb (7 858 kg)
Tipping load SAE:
Straight 19,548 lb (8 867 kg) 19,563 lb (8 420 kg) 18,904 lb (8 575 kg)
40 turn 16,394 lb (7 436 kg) 15,485 lb (7 024 kg) 15,801 lb (7 167 kg)
Lift capacity:
Full height 14,654 lb (6 647 kg) 13,903 lb (6 306 kg) 14,072 lb (6 383 kg)
Maximum reach 19,570 lb (8 877 kg) 18,758 lb (8 508 kg) 18,944 lb (8 593 kg)
Ground 23,269 lb (10 554 kg) 22,412 lb (10 166 kg) 22,734 lb (10 312 kg)
Breakout force with tilt cylinder 22,198 lb (10 069 kg) 26,226 lb (11 896 kg) 28,082 lb (12 738 kg)
Loader clearance circle with bucket 523.0 in (13 285 mm) 516.2 in (13 111 mm) 521.5 in (13 247 mm)
721F Page 6 of 10
PERFORMANCE DATA
721F Z-Bar* 2.6 yd3 (1.9 m3) 4-IN-1 Bucket on CNH Z-Bar coupler
SAE bucket capacity struck 2.2 yd3 (1.71 m3)
Heaped 2.6 yd3 (1.98 m3)
Bucket width outside 106.3 in (2 700 mm)
Bucket weight 5,000 lb (2 268 kg)
E. Operating height fully raised with spillguard 211.5 in (5 371 mm)
F. Hinge pin height fully raised 156.5 in (3 976 mm)
G. Overall length bucket level on ground 302.5 in (7 684 mm)
Dump angle fully raised 55
H. Dump height fully raised, 45 dump 114.4 in (2 905 mm)
J. Bucket reach fully raised, 45 dump 45.3 in (1 150 mm)
K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 65.8 in (1 671 mm)
Operating load ISO 10,027 lb (4 548 kg)
Operating load SAE 9,006 lb (4 085 kg)
Maximum material density ISO 3,872 lb/yd3 (2 297 kg/m3)
Maximum material density SAE 3,477 lb/yd3 (2 063 kg/m3)
Tipping load ISO:
Straight 23,223 lb (10 534 kg)
40 turn 20,053 lb (9 096 kg)
Tipping load SAE:
Straight 21,643 lb (9 817 kg)
40 turn 18,9010 lb (8 169 kg)
Lift capacity:
Full height 13,750 lb (6 237 kg)
Maximum reach 19,886 lb (9 020 kg)
Ground 26,464 lb (12 004 kg)
Breakout force with tilt cylinder 30,119 lb (13 662 kg)
Maximum rollback:
Ground 39
Carry position 43
@ Maximum reach 54
@ Full height 57
L. Dig depth 3.0 in (77 mm)
Maximum grading angle with bucket back dragging 59
Loader clearance circle with bucket 498.5 in (12 661 mm)

721F XR 2.6 yd3 GP (1.9 m3) 4-IN-1 Bucket on Z-Bar coupler

E. Operating height fully raised with spillguard 227.0 in (5 765 mm)
F. Hinge pin height fully raised 172.1 in (4 371 mm)
G. Overall length bucket level on ground 316.6 in (8 042 mm)
Dump angle fully raised 55
H. Dump height fully raised, 45 dump 129.9 in (3 299 mm)
J. Bucket reach fully raised, 45 dump 45.3 in (1 151 mm)
K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 78.1 in (1 983 mm)
Operating load ISO 8,236 lb (3 736 kg)
Operating load SAE 7,447 lb (3 378 kg)
Maximum material density ISO 3,180 lb/yd3 (1 887 kg/m3)
Maximum material density SAE 2,877 lb/yd3 (1 707 kg/m3)
Tipping load ISO:
Straight 19,251 lb (8 732 kg)
40 turn 16,471 lb (7 471 kg)
Tipping load SAE:
Straight 18,060 lb (8 192 kg)
40 turn 14,897 lb (6 757 kg)
Lift capacity:
Full height 12,647 lb (5 737 kg)
Maximum reach 17,575 lb (7 972 kg)
Ground 21,740 lb (9 861 kg)
Breakout force with tilt cylinder 29,950 lb (13 585 kg)
Loader clearance circle with bucket 511.2 in (12 984 mm)

721F Page 7 of 10
PERFORMANCE DATA
721F XT 3.0 yd3 GP (2.3 m3) Bucket 3.0 yd3 GP (2.3 m3) Bucket 2.6 yd3 GP (2.0 m3) 4-IN-1
with CNH XT Coupler on CNH XT Coupler Bucket on CNH
(JRB Compatible) (JRB Compatible) XT Coupler
with Bolt-On Edge with Teeth Only
E. Operating height fully raised with spillguard 217.3 in (5 519 mm) 217.3 in (5 519 mm) 217.4 in (5 522 mm)
F. Hinge pin height fully raised 163.8 in (4 160 mm) 163.8 in (4 160 mm) 163.7 in (4 158 mm)
G. Overall length bucket level on ground 312.2 in (7 931 mm) 318.2 in (8 083 mm) 305.0 in (7 747 mm)
Dump angle fully raised 55 55 55
H. Dump height fully raised, 45 dump 115.0 in (2 921 mm) 111.1 in (2 822 mm) 119.6 in (3 038 mm)
J. Bucket reach fully raised, 45 dump 50.4 in (1 279 mm) 54.6 in (1 386 mm) 44.6 in (1 133 mm)
K. Bucket reach 7 ft 0 in (2.13 m) height, 45 dump 72.1 in (1 832 mm) 74.4 in (1 889 mm) 68.5 in (1 739 mm)
Operating load ISO 9,879 lb (4 481 kg) 10,071 lb (4 568 kg) 9,689 lb (4 395 kg)
Operating load SAE 8,924 lb (4 048 kg) 9,101 lb (4 128 kg) 8,686 lb (3 940 kg)
Maximum material density ISO 3,358 lb / yd (1 992 kg / m )
3 3
3,615 lb / yd (2 145 kg / m )
3 3
3,742 lb/yd3 (2 220 kg/m3)
Maximum material density SAE 3,032 lb / yd (1 799 kg / m )
3 3
3,266 lb / yd (1 938 kg / m )
3 3
3,354 lb/yd3 (1 990 kg/m3)
Tipping load ISO:
Straight 22,683 lb (10 289 kg) 23,093 lb (10 475 kg) 22,392 lb (10 157 kg)
40 turn 19,758 lb (8 962 kg) 20,139 lb (9 135 kg) 19,379 lb (8 790 kg)
Tipping load SAE:
Straight 21,222 lb (9 626 kg) 14,996 lb (6 802 kg) 20,847 lb (9 456 kg)
40 turn 17,846 lb (8 095 kg) 18,204 lb (8 257 kg) 17,372 lb (7 880 kg)
Lift capacity:
Full height 14,288 lb (6 481 kg) 14,526 lb (6 589 kg) 13,325 lb (6 044 kg)
Maximum reach 19,989 lb (9 067 kg) 20,186 lb (9 156 kg) 18,838 lb (8 545 kg)
Ground 31,028 lb (14 074 kg) 30,988 lb (14 056 kg) 29,363 lb (13 319 kg)
Breakout force with tilt cylinder 27,860 lb (12 637 kg) 29,853 lb (13 541 kg) 31,837 lb (14 441 kg)
Loader clearance circle with bucket 613.9 in (15 592 mm) 499.5 in (12 687 mm) 492.9 in (12 519 mm)
NOTE: *Z-Bar performance data shown with full counterweight.
Performance data unit equipped with 20.5R25 Michelin XHA TL tires, ROPS cab with heater and A/C, full counterweight, standard batteries, front and rear fenders, full fuel
and 175 lb (75 kg) operator. Specifications per SAE J732, J1234, J695, J742 and J818.

FORKS
721F Z-Bar 721F XT 721F XR
Fork attachment weight including coupler 2,663 lb (1 208 kg) 2,385 lb (1 082 kg) 2,663 lb (1 208 kg)
Operating load per EN 474-3:
Rough terrain 8,356 lb (3 790 kg) 8,289 lb (3 760 kg) 7,355 lb (3 336 kg)
Firm and level ground 199.0 in (5 054 mm) 197.4 in (5 013 mm) 175.2 in (4 449 mm)
Tipping load straight ISO 291.7 in (7 410 mm) 288.6 in (7 330 mm) 258.3 in (6 561 mm)
Tipping load at 40 turn ISO 248.7 in (6 317 mm) 246.7 in (6 266 mm) 218.9 in (5 561 mm)
Unit operating mass 31,559 lb (14 315 kg) 31,500 lb (14 288 kg) 32,040 lb (14 533 kg)

721F Page 8 of 10
STANDARD EQUIPMENT
OPERATOR ENVIRONMENT DRIVETRAIN (continued) ELECTRICAL (continued)
See page 1 Downshift button 120 amp alternator
ENGINE Torque converter (2) 700 CCA 12-volt batteries
Case/FPT F4HFE613T Limited-slip differentials Z-Bar Electric starter
Tier 4 Final Certified Heavy-duty axles XT/XR: Lights:
Selectable work modes: with auto-locking front differential, 2 Front and 2 rear halogen flood lights
Maximum Power rear conventional differential and 2 Front driving headlights high/low beam
Standard Power with bronze sintered brake pads with integrated turn signals
Economy Power Outboard planetary axles 2 LED stop/ tail lights with integrated turn
Auto Power signals
Transmission oil cooler
Turbocharger Key start/ stop switch
Brake pedal transmission disconnect declutch
Charge air cooling Backup alarm
Hydraulic wet disc brakes
Automatic belt tensioner Centrally located fuse box
Spring-applied hydraulic release parking brake with all electrical circuits protected
Integral engine oil cooling Limp-Home Mode Remote jump start receptacle
Fuel filter with water trap Greasable rear axle trunnion TELEMATICS
Dual-element dry-type air cleaner 3-piece rims
CASE SiteWatch Telematics includes
Hydraulic-driven cooling fan HYDRAULICS hardware and a 3-yr Advanced
Air-cooled radiator 2-function loader valve data subscription
Mid-mounted cooling module with joystick control OTHER
Common rail electronic fuel injection Low-effort steering Electric hood lift
DRIVETRAIN Hydraulic driven cooling fan Front and rear fenders, partial coverage
4-wheel drive Diagnostic quick couplers Heavy counterweight
4F/3R Selectable autoshift/manual shift Split flange hydraulic connections Drawbar hitch
transmission 1 in or greater
Articulation locking bar
Electronic Control Module programmable, LOADER
computer controlled proportional shifting Lift arm locking bar
See page 2 Operating weight, Other
with programmable gear selection specifications Lift and tie-down points front/rear
Onboard diagnostics ELECTRICAL Remote drain points
Single lever electronic shift control Alternator and voltage regulator Grouped remote-mounted ecology drains:
F/N/R switch in loader control handle Engine oil
Electrical disconnect Engine coolant
Hydraulic oil
OPTIONAL EQUIPMENT
OPERATOR ENVIRONMENT DRIVETRAIN ADVANCED ENGINE AIR FILTRATION
Heated cloth-covered air suspension seat 5F / 3R Autoshift/manual shift transmission, Heavy Debris cooling system:
Cloth mechanical suspension seat lockup torque converter, PowerInch de-clutch Slanted cooling module cover
Heavy-duty axles Z-Bar: Auto reversing fan
Headrest Sy-Klone ejective air pre-cleaner
with auto-locking front differential,
3 in (76 mm) retractable seat belt rear conventional differential and Increased cooling fin spacing
Sound Shield noise suppression package with bronze sintered brake pads Added cooling module sealing
Cab with heater only no AC Cold weather package: Variable speed hydraulic reversing fan
Radio-ready 12 or 24-volt Heavy-duty (2) 950 CCA 12V batteries Full view air pre-cleaner
with auxiliary power 12-volt Grid heater Sy-Klone ejective air pre-cleaner
Fuel heater
AM/FM stereo radio Hydraulic oil cooler bypass OTHER
Cab convenience package: ashtray, 24V cigar Low temperature hydraulic oil Additional RH steps and platform w/ standard or
lighter and cell phone holder Fast-warm hydraulic valve wide fenders
Rotating beacon TIRES Side guards for rear frame
Right hand brake pedal 20.5-25 16 PR L2 bias dirt/ traction Tool box ground level access
External rearview mirrors 20.5-25 16 PR L3 bias rock Light counterweight Z-Bar
External rearview mirrors, heated 20.5 R25 L2 radial dirt/ traction Fire extinguisher
In-cab accessory mount no rear view camera 20.5 R25 L3 radial rock License plate bracket
Rear view camera with accessory mount 20.5 R25 radial Michelin SnoPlus 12.4 mph (20 kph) maximum speed control
Extra front-facing work lights 20.5 R25 radial Bridgestone Snow Wedge Special paint
HYDRAULICS SolidFlex HD solid tires on adapter rims GUARDING
Auxiliary hydraulics Spare wheels and tires Skid plate, transmission and front chassis
Ride Control Axle oscillation stops bottom guards
Secondary steering LOADER Windscreen guard
Joystick steering with and without secondary XR extended reach version Specialized guarding package:
steering Windscreen, articulation, front cover,
XT tool carrier version chassis bottom, skid plate, transmission,
2-function loader valve with single access Attachment auxiliary hydraulics lift cylinder, front lights, fuel tank, metal
control wrapped hoses and cylinder debris ejectors
Coupler systems JRB or ACS compatible
3- function loader valve with 3 lever control or
with joystick plus lever Buckets see pages 4 through 8
4 1 clamp buckets
Forks
721F Page 9 of 10
NOTE: All specifications are stated in accordance with SAEStandards or Recommended Practices,
where applicable.
NOTE: All engines meet current EPA emissions requirements.
IMPORTANT: Case Construction Inc. reserves the right to change these specifications without notice
and without incurring any obligation relating to such change. Case Construction Inc. does not warrant
the safety or reliability of attachments from other manufacturers.
CASE is a trademark registered in the United States and many other countries, owned by or licensed to
CNH Industrial N.V., its subsidiaries or affiliates. CNH Industrial Capital is a trademark in the United States
and many other countries, owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates.
www.casece.com

Form No. CCE201503721F Printed in U.S.A. 2015 CNH Industrial America LLC
Replaces Form No. CCE201411721F 721F Page 10 of 10 All Rights Reserved

All Case construction equipment is biodiesel ready.