PC version info

Version 3.51
BNet-Office and SL/SDL
New BNet-Office and SL/SDL version V3.51. This concerns the following versions:
o Beissbarth Standard version
o Beissbarth Porsche version
o Beissbarth Middle East version
o Bosch Standard version
o Bosch Middle East version
Starting with this version the BNet connection to the ASA Network is available without any needed
licence key (dongle).
See chapter Bug fixes: Fixed some bugs

BNetTool
The size of the dialog for the configuration values (hardware configuration, test program
configuration) has been increased.

Version 3.50
BNet-Office and SL/SDL
New BNet-Office and SL/SDL version V3.50. This concerns the following versions:
o Beissbarth Standard version
o Beissbarth Porsche version
o Beissbarth Middle East version
o Bosch Standard version
o Bosch Middle East version
New drivers for BNet/USB-Converter NSR-3260
See chapter Bug fixes: Fixed some bugs

BNetTool
-

Version 3.40
BNet-Office and Screen Lane
New BNet-Office and ScreenLane version V3.40 (concerns standard version, Bosch version,
Porsche version and Middle East version).
Integrated all actual files of the Theta-Tester SAT69x.
Motorcycle brake test on a BD5xx/BD6xx/BD7xx series car brake tester.
Integrated the feature Pedders for Pedders Suspension in Australia
See chapter Bug fixes: Fixed some bugs

BNetTool
Hardware configuration of the brake tester: Improved the description of the configuration value
Nominal frequency of slip roller
Hardware configuration value Length of the sideslip plate was corrected to 730 mm.

Version 3.11
BNet-Office and Screen Lane NMI
BNet-Office and ScreenLane version V3.11 for NMI.
Changed the firmware version from 2.75 to the declared version 3.00.
 Integrated all actual files of the Theta-Tester SAT69x.

Version 3.30
BNet-Office and Screen Lane
New BNet-Office and ScreenLane version V3.30 (concerns standard version, Bosch version,
Porsche version and Middle East version).
Supporting Theta Tester SAT695 with noise simulation.
Supporting MLD540 Headlight tester.
New Setup and drivers (NSR 3260 converter, USB-LON) for Windows 7 64 bit.
Configurable Export of orders to Order listing directory, depending on order state and location.
Supporting DEKRA requirements:
o Global data folder and Logfile path.
o Remote control commands on keyboard.
o Setup for silent installation.
o Operating mode without hardlock dongle.
o Automatic order activation.
o Sending brake, suspension and sideslip results as one position in ASA format.
o Special order states filter (only 2 Buttons).
o Installing all software modules and configure the active modules in BNConfig.
o Sending results to DEKRA software once again.
Export of live data in XML format through file gateway (for curve printouts in DXP).
Truck printouts for Bosch.
Enhancement of headlight test printouts for additional values (Yaw angle, dazzling).
New database entry for RB-Key.
Supporting new generation of noise simulator tester (new frequency converter).
Enhancement of standard printouts with CAS[plus] measurement.
Suspension printouts for Pedders
Livestream support lt. Bremsprfstandrichtlinie Verkehrsblatt 9/2011

Version 3.10
BNet-Office and Screen Lane NMI
BNet-Office and ScreenLane version V3.10 for NMI.
Full support of a second pedal force sensor connected to the side slip sensor port of the BD600.
Attention: It is not possible to connect both the second pedal force sensor and the side slip sensor
to the BD600!
All features of the standard version V2.50 are included in the NMI-version.
o Lift for brake tester
o Colored printouts and graphical printouts
o Improved 4wd detection
o Curve visualisation for brake test
o Support new generation of suspension tester with flywheel
o Input of permissible total weight by remote control in superautomatic mode
New setup to support Windows 7 32bit and 64bit. Installed software can be modified by control
panel / add or remove programs and inserting installation media.
New order state part worked on.
Improvement of order list updates and order state filters from Ordermanager.
Order sorting by second name instead of first name.
Configurable order finishing for screen lane with additional states (part worked on).
Removed warning phase at 1450kg, and increased overload limit to 1650kg.
Supporting Theta Tester SAT695 with noise simulation.
Supporting MLD540 Headlight tester.
Supporting new generation of noise simulator tester (new frequency converter).
New Setup and drivers for Windows 7 64 bit.
Version 2.82
BNet-Office and Screen Lane
New BNet-Office and ScreenLane version V2.82 (concerns standard version, Bosch version,
Porsche version and Middle East version).
New gateway for MLD540 Headlight tester. Upgrading database, BNConfig, EntryWizard and
printouts for additional values from MLD540.
Maximum order age can be configured for Ordermanager. Older orders are deleted automatically.
Automatic creation of active orders (configurable). Orders will be created with a licence plate
number, depending on the StationID and automatically activated. For example: If the StationID is
A, the orders are created with licence plate numbers A-00, A-01, A-02, A-99.
HC limit and HC state for emission petrol test. Upgrading database, EntryWizard and printouts for
these additional values.

Version 2.80
BNet-Office and Screen Lane
New BNet-Office and ScreenLane version V2.80 (concerns standard version, Bosch version,
Porsche version and Middle East version).
New setup to support Windows 7 32bit. Installed software can be modified by control panel / add
or remove programs and inserting the installation media. It is also possible to update this version
with later versions or update previous version V2.50 with this version without modifying the
configuration of the installed version.
New order state part worked on.
Improvement of order list updates and order state filters from Ordermanager.
Order sorting by second name instead of first name.
Configurable order finishing for screen lane with additional states (part worked on).
Removed warning phase at 1450kg, and increased overload limit to 1650kg.
StarGasGateway connected via RS232.
Special Visual Check template for Greece (configurable in BNConfig).
New version of FileGateway exports results in ASA XML format (for SPPlus support,
configurable).
New version of FileGateway could synchronize BNet Database with other vendors system
(configurable).
Version 2.50
BNet-Office and Screen Lane
New BNet-Office and ScreenLane version V2.50 (concerns standard version, Bosch version,
Porsche version and Middle East version)
New setup to support Windows Vista and modify installed software without inserting CD. It is also
possible to update this version later without modifying the configuration of the installed version.
Integration of Theta-tester SAT690/695.
New Ordermanager with different operating modes (standard and pipeline). Orders are grouped
by licence plate, manufacturer and model. It is possible to assign quickjob results to another order
in pipeline mode. Positions view is not longer necessary, because all information is located in
Order view. Ordermanager could be configured to import and export orders in different ways (no
import or export, only customer and vehicle data, all data).
New version of Filegateway exports all orders that are not finished or archived as file in a
configurable folder. Filegateway could also import results and assign them to an order witch is not
active, if id is located in result file. Filegateway could be configured to import and export orders
in different ways (no import or export, only customer and vehicle data, all data).
In Overload condition of suspension tester the weight can be assigned to the axle without leaving
the superautomatic mode.
Screen lane can be configured to hide measured values and results of brake, suspension or
sideslip test (Colombia).
BNet-Office setup is not longer necessary. This version can be configured in BNet-Config.

BNetTool
-

Version 2.30
BNet-Office and Screen Lane
New BNet-Office and ScreenLane version V2.30 (concerns standard version, Bosch version,
Porsche version and Middle East version)
OES design for BMW, Mercedes and VAG (printouts and ScreenLane startup screen).
Removed the possibility to import order data into the Ordermanager.
Integrated new language Turkish.

BNetTool
Printouts for the device configuration and device calibration.

Version 2.20
BNet-Office and Screen Lane
New BNet-Office and ScreenLane version V2.20 UK (MOT + ATL)

BNetTool
-
Version 2.10
BNet-Office and Screen Lane
New BNet-Office and ScreenLane version V2.10 (concerns standard version, Bosch version,
Porsche version and Middle East version)
Improved sorting in the order list of the Ordermanager
Removed the possibility to copy and paste measurement results in the Ordermanager
Added the possibility to disable the manual input of measurement results
Added the possibility for configurable customer logos on the printouts
Extended the suspension test evaluation: Absolute or relative road grip difference evaluation is
possible now
Printouts: The version number of the TL/SL-series is shown on the printouts now
Integrated new languages Thai and Macedonian.

BNetTool
-

Version 2.01
BNet-Office and Screen Lane
New BNet-Office and ScreenLane version V2.01 (concerns only Bosch version)
New BNet-Office and ScreenLane version for Bosch
Integrated new language Japanese
New brake force difference graph in the curve printout
New road grip graph in the curve printout

BNetTool
-

Version 2.00
BNet-Office and Screen Lane
New BNet-Office and ScreenLane version V2.00 (concerns standard version, Porsche version
and Middle East version)
Added support for BD700.
Added support for Bosch emission analyzers BEA 150/250/350/450/460/850.
Extended manual inputs for gas tests and smoke tests.
Extended printouts for gas tests and smoke tests.
Middle East version: Supports the FFB microgas 4 PC gas and diesel tester with the operating
system Windows XP (not Windows 98).
Integrated new languages Serbian, Latvian and Vietnamese.
SA/SN: Nominal load limit for SA640 is changed to 2000kg and for SN680 has remained like
before 1450kg.

BNetTool
-
Version 1.91
BNet-Office and Screen Lane
New Screen Lane version V1.91 (concerns standard version, Porsche version and Middle East
version)
Improved BNet-Office networking: Better interconnections of different BNet-Office versions.
BNet-Office with Screen Lane and BNet-Office with STL9000.
Middle East versions: Improved text output for right to left languages (Arabic, Hebrew, Farsi).
Middle East versions: The layout of the program BNConfig is mirrored.
BD600 4x4 detection: If the brake tester detects a 4x4 drive the Screen Lane will instruct the
operator to switch of the engine.

BNetTool
-

Version 1.90
BNet-Office and Screen Lane
New Screen Lane version V1.90 (concerns standard version, Porsche version and Middle East
version)
Integrated new languages Chinese and Hebrew.
Added newer device driver for the software licence manager (Hardlock).
The Screen Lane displays all important result values during the printout. In the test lane operation
mode it displays the result values of the sideslip test, the suspension test and the brake test. In
the test program operating mode it displays the result values of the brake test.
SA600/SN 600 series: Evaluation of the road grip difference.
BD600 series: New configuration entry to configure the pedal force switch off limit.
ST600 series: New configuration entries to configure independent limits for the side slip results of
front axle and rear axle.

BNetTool
New BNetTool version 4.0.0.1 (concerns standard version, Porsche version and Middle East
version).
The analogue display BD600/BD500 will be automatically used as a monitor display for the
manual calibration mode of the BNetTool (firmware version 2.42 or later required).
The BNetTool displays all error and warning messages (firmware version 2.42 or later required).
The access to blocked or reserved devices can be enforced.
Added support for BD700.
Version 1.80
BNet-Office and Screen Lane
New Screen Lane version V1.80 (concerns standard version, Porsche version and Middle East
version)
Integrated new language Czech.
BD600 series: Support for the new pneumatic lifting device
BD600 series: The test program can be configured with two separate limits for the brake force
imbalance. Limit one for the front axle, limit two for the rear axle. This feature is only needed in
Denmark.
SN600 series: Support for the new suspension tester SN680 Power with flywheel and motor fan
control.

BNetTool
New BNetTool version 3.9.0.1 (concerns all versions).
Support for BNet PlugnPlay devices.

Version 1.70
BNet-Office and Screen Lane
NMI-version update
Full support of a second pedal force sensor connected to the side slip sensor port of the BD600.
Attention: It is not possible to connect both the second pedal force sensor and the side slip sensor
to the BD600!
All features of the standard version V1.50 are included in the NMI-version

Version 1.60
BNet-Office and Screen Lane
MOT-version update
All features of the standard version V1.50 are included in the MOT-version

MCA4PC Gateway
Included special installation program for the microgas 4 PC exhaust fume and diesel tester.
The MCA4PC gateway connects the microgas 4 PC exhaust fume and diesel tester with a BNet
PC. The measurement results are stored on the BNet dataserver.
This installation program also supports all SL V1.50 versions.

Version 1.51
BNet-Office and Screen Lane
New Screen Lane version V1.51 (only concerns standard version)
Implementation of a tare function for the suspension tester
Reset of up to two unintended side slip measurements in the superautomatic mode of a test lane

BNetTool
New BNetTool version 3.6.1.1 (only concerns standard version)
Version 1.50
BNet-Office and Screen Lane
New Screen Lane version V1.50 (only concerns standard version, Porsche version and Middle
East version)
New Version Middle East
Integrated new languages. Screen Lane now supports the following languages:
AR1=Arabia
B=Belgium
BG=Bulgaria
D=Germany
DK=Denmark
E=Spain
EST=Estonia
FIN=Finland
GB=Great Britain
GR=Greece
HR=Croatia
IR=Iran
LT=Lithuania
NL=Netherlands
N=Norway
PL=Poland
P=Portugal
RO=Romania
RUS=Russia
S=Sweden
Support for BNet/USB converter NSR-3260
Support for the automatic button of the analog display in monitor mode
Support for the new PC cabinet with the remote control receiver Irman
Curve printout for BD600 and BD500 series
Curve display during measurement of BD600 series

BNetTool
New BNetTool version 3.6.0.3 (only concerns standard version and Middle East version)
Concurrent installation with BNetTool mtl69/STL70 on a service Laptop is now possible

Version 1.40
Interim version for test cases
Version 1.30
BNet-Office and Screen Lane
New Screen Lane version V1.30 (only concerns standard version and Porsche version)
Integrated new languages. Screen Lane now supports the following languages:
B=Belgium
BG=Bulgaria
D=Germany
DK=Denmark
E=Spain
EW=Estonia
FIN=Finland
GB=Great Britain
HR=Croatia
LT=Lithuania
NL=Netherlands
N=Norway
PL=Poland
P=Portugal
RUS=Russia
Better support for Windows power management. The PC cant go into sleep mode or standby
mode, when the Screen Lane is running.

BNetTool
New BNetTool version 3.4.0.5 (concerns standard version, Porsche version, NMI version and
MOT version)
Support for save download. After a power failure during a firmware download you can continue
this download. This is only possible with firmware files greater or equal version 2.10.
Clear representation of production software. New production software is displayed differently than
test lane software. This is not possible for devices which are already delivered.
Clear differentiation between production software BD500 series and production software BD600
series.
Clearer error messages with detailed information for problem solution
Remote control is locked outside calibration mode.
Better remote operation in calibration mode
Improvement of Resolve fieldbus deadlock
Bug Fixes
Version 3.51
BNet-Office and SL/SDL
Solved a BNet printout problem concerning Windows 7 (32-Bit, 64-Bit). The BNet printout
application crashed on some systems under Windows 7.
Solved a Microsoft component installation problem. The component has not been installed in any
case. Therefore our BNet application did not start.
Solved a problem with the computer BX12 in combination with the new BIOS (version C52F1S08).
A correct installation of the Hardlock driver for the Software Licence Manager was not possible.

BNetTool
-

Version 3.50
BNet-Office and SL/SDL
Solved a problem with the start of the motors of the brake tester. In the previous versions the
motor of the brake tester sometimes does not start. The brake tester stayed in the state Standby
or in the state Attention! Motor starts.
Solved a problem with the BNet-Office installation. In the previous version an update installation
does not install the new firmware files.
Solved a problem with the start of the Hostmanager application. In the previous version it was
possible to start the application Hostmanager twice.
Test lane with sideslip plate and brake tester:
Test lane with sideslip plate, Theta-Tester and brake tester:
Solved a problem introduced in the previous version SL/SDL 3.40. The limits if the sideslip test
were out of range (correct limits -6 .. + 6). Therefore the printout und the evaluation was not
correct. This problem was solved in the firmware.
Test lane with sideslip plate, Theta-Tester and brake tester:
Solved a problem with vehicles with a very short distance between the axles, e. g. Mercedes
Smart. These vehicles simultaneously stand in the brake tester and on the side-slip plate. In the
previous versions the software detected warning 14 or warning 11 in the Automatic or
Superautomatic operating mode and exited the Automatic or Superautomatic operating mode.
This detection of warning 14 or warning 11 was not correct. This problem was solved in the
firmware.

BNetTool
-

Version 3.40
BNet-Office and Screen Lane
Integrated all actual files of the Theta-Tester SAT69x. This fixes the following problems:
o The SAT program hangs during startup.
o The ScreenLane loses the Windows focus. Therefore the motors of the brake tester dont
start.
o Automatic operation mode: The takeover of the weight from the SAT69x to the
ScreenLane is faulty.
o BNet programs, e. g. ScreenLane and Ordermanager, could be started more than once.
This is possible with a double click to the BNet Start icon on the Windows desktop.
o On Windows 7 the LON driver of the SAT69x is not installed automatically. He must be
installed manually after the normal installation.
o On Windows 7 64-Bit the SAT69x program displays a warning message during startup.
The user has to confirm this message. This is due to an old version of the Hardlock
dongle driver. The new version of the Hardlock dongle driver is 6.23.0.0.
Beissbarth version, ScreenLane: In the previous version after the installation the brake tester
program displays curves instead of pillars. Correct are pillars. This behaviour was corrected.
 Bosch version, Office-Test-Lane mode: In the previous version the BNet-Office-gateway is visible
as a ScreenLane window. Normally it should only be visible in the system tray of Windows. This
behaviour was corrected.
Test lane with sideslip plate and brake tester:
Test lane with sideslip plate, Theta-Tester and brake tester:
Solved the problem that two unintended sideslip measurements were not automatically reset after
20 seconds. Two unintended sideslip measurements can occur when a car is driving back over
the test lane devices.
For test lanes with sideslip plate, suspension tester SA/SN and brake tester this problem was
already solved years ago.
Solved a problem with the DEKRA superautomatic timeout value. The test program configuration
value 39 Superautomatic timeout was not working well in all circumstances.
Solved a problem with the 4wd detection. The 4wd detection was not working well in all
circumstances, especially in the superautomatic mode of a test lane.

BNetTool
-

Version 3.11
BNet-Office and Screen Lane NMI
Integrated all actual files of the Theta-Tester SAT69x. This fixes the following problems:
o The SAT program hangs during startup.
o The ScreenLane loses the Windows focus. Therefore the motors of the brake tester dont
start.
o Automatic operation mode: The takeover of the weight from the SAT69x to the
ScreenLane is faulty.
o BNet programs, e. g. ScreenLane and Ordermanager, could be started more than once.
This is possible with a double click to the BNet Start icon on the Windows desktop.
o On Windows 7 the LON driver of the SAT69x is not installed automatically. He must be
installed manually after the normal installation.
o On Windows 7 64-Bit the SAT69x program displays a warning message during startup.
The user has to confirm this message. This is due to an old version of the Hardlock
dongle driver. The new version of the Hardlock dongle driver is 6.23.0.0.

BNetTool
-

Version 2.50
BNet-Office and Screen Lane
Input fields are protected. For example: In vehicle mileage, the user can only input numbers.
Overload weight can be assigned to an axle in testlane manual mode.

BNetTool
-

Version 2.30
BNet-Office and Screen Lane
Solved problem with the Software Licence Manager (Dongle). The Software Licence Manager
didnt work on some multi-core processors.

BNetTool
-
Version 2.20
BNet-Office and Screen Lane
-

BNetTool
-

Version 2.10
BNet-Office and Screen Lane
-

BNetTool
-

Version 2.01
BNet-Office and Screen Lane
-

BNetTool
-

Version 2.00
BNet-Office and Screen Lane
-

BNetTool
-

Version 1.91
BNet-Office and Screen Lane
-

BNetTool
-

Version 1.90
BNet-Office and Screen Lane
-

BNetTool
-

Version 1.60
BNet-Office and Screen Lane
BD600 UK: Solved problems with the calculation of the brake force difference.

BNetTool
-
Version 1.51
BNet-Office and Screen Lane
Eliminated some errors in the English translations

BNetTool
-

Version 1.50
BNet-Office and Screen Lane
Solved problems with database update during installation of Screen Lane.
Solved problem with the superautomatic peak value display. In rare cases the superautomatic
peak value display only stopped after pressing the STOP key, even when the vehicle is on the test
stand.
Other minor bug fixes

BNetTool
-

Version 1.30
BNet-Office and Screen Lane
-

BNetTool
Solved problems with translations in some countries (e. g. Russia, Iran, ).