Model NPR200

GVM
GCM
Engine Type:
4,490kg
7,990kg
Isuzu SiTEC 110
NPR
Displacement: 4,334 cc
Power*:
Torque*:
85 kW @ 3,200 RPM
285 Nm @ 1,800 RPM
200
Cab/Chassis specification as at September 2000

CABIN SPECIFICATIONS AND APPOINTMENTS

• Centre fascia and driver’s door ash trays.
CABIN EXTERIOR CABIN INTERIOR • Interior lamp with On / Door / Off switch.
• All steel cabin with manual tilting to 45º. • Entry assist handles on ‘A’ pillars.
• Extended front wheel arch spray suppression • Passenger side assist grip. CONTROLS
guards. • Driver’s bucket seat with reclining back and fore- • Key-operated engine start / stop and steering
• 90º opening, internally reinforced doors. aft adjustment. 2-person passenger bench seat lock. Engine fast-idle vernier.
• Aluminium, non-slip entry steps. with folding seat back. Seat cushion tilts for
access to engine. Fire resistant cloth seat facings. • Left Side Combination Stalk: Windshield wipers
• “West Coast” type rear view mirrors. Flat mirror and washer.
glass with additional, independently adjustable • 3-point, lap-sash seatbelts with emergency
locking belt retractors in outboard seating • Right Side Combination Stalk: Turn signals;
convex “spot” mirror on both sides. position, main and high beam lamps.
• Access to fluid check points without tilting cab. positions. 2-point lap seatbelt in centre seating
position. Hazard flash switch.
• Tinted and laminated windshield. • Additional interior lamp switch on instrument
• Driver and passenger fold-down sun visors.
• 2-speed windshield wiper system with panel adjacent to driver’s door.
intermittent mode. Windshield washer system • Interior rear-vision mirror.
with triple washer jets on each wiper arm. • Full interior panel trim with padded roof lining and INSTRUMENTATION
• 4 rectangular, semi-sealed type headlamps. vinyl floor mats. Windscreen header storage shelf.
• “Glove” compartment with door. • Gauges: Electronically driven speedometer and
tachometer. Digital odometer with integrated, dual
• “Soft feel” urethane steering wheel. tripmeter. Engine coolant temperature and fuel level.
• Steering column with tilt and telescope • Warning Lamps: Low battery charge, brake
adjustments. failure, low fuel level, glow plug, water separator.
• Heater / Demister with 4-speed fan and • Indicator Lamps: Turn signals, parking brake,
windscreen, face and floor outlets. high beam.
• Optional fully integrated air conditioning.
• Fore-aft adjustable roof vent. TOOLS
• AM / FM Stereo Radio / Cassette with integrated • Chassis frame mounted spare wheel and tyre
digital clock. Optional 6 stack CD player. winch. Wheel changing tools including 4,000 kg
• Centre fascia pull-out drinks holder. capacity hydraulic jack. Hand tools in kit bag.
• Easy access fuse panel (behind glove
compartment door).
• Windshield washer reservoir under glove
compartment.

ISUZU NEW TRUCK WARRANTIES

STANDARD TRUCKPOWER WARRANTY* TRUCKPOWER EXTENDED WARRANTY OPTIONS#
NEW VEHICLE 2 years 50,000km
3 years / 100,000km 4 years / 150,000km 5 years / 200,000km
DRIVETRAIN 3 years 100,000km
CAB CORROSION 3 years unlimited

* Subject to the conditions outlined in the I-GM New Vehicle Warranty, the Isuzu NPR models carry a standard factory warranty which covers the owner: (i) for the entire vehicle, for the first
24 months or 50,000km (whichever comes first) (ii) for the powertrain, which runs concurrently, for 36 months or 100,000km (whichever comes first) (iii) against cab corrosion, for 36 months
and unlimited kilometres.
# A TruckPower Extended Warranty as illustrated is available by purchase to cover the owner against the failure of original components, but excludes some components and expendable items
such as oil, filters, etc. Please consult with your Isuzu Dealer for full details obtainable from a dedicated brochure available to customers.

ISUZU-GENERAL MOTORS AUSTRALIA LTD A.C.N. 006 962 572. PLEASE NOTE: as the policy of I-GM is one of continual product improvement, all specifications and equipment are
subject to change without notice. No I-GM dealer or other person is authorised or permitted to give or make any statement, assertion or undertaking in relation to the quality, performance,
characteristics, descriptions or fitness for any purpose of any I-GM product or in connection with the supply of any I-GM product which is at variance with any written statement, assertion or
undertaking on any of these subjects given or made by I-GM in its published sales literature, and the company accepts no liability for any such unauthorised action. I-GM has franchised dealers
in many parts of Australia, for the sale of service, parts and the provision of service to the owners of I-GM products. Every endeavour is made to ensure that such dealers carry adequate stocks
of service parts and are equipped to provide satisfactory service, but makes no promise, other than that contained in the I-GM new vehicle warranty, that such parts or service facilities will be
available or available at any specific location or at any particular time. A word about this specification sheet. We have tried to make it as comprehensive and factual as possible. However, since
the time of printing some of the information you will find here may have been updated. Also, some of the equipment shown or described through this specification sheet may have been changed
and/or is available at extra cost. And the right is reserved to make changes at any time without notice, in prices, colours, materials, equipment and models. Your I-GM dealer has details and
before ordering, you should ask him/her to bring you up to date.
RGS/IGM3107
 NPR 200 Short/Medium
DRIVELINE SPECIFICATIONS
EXHAUST SYSTEM
ENGINE: SiTEC 110 (ISUZU 4HF1) • Horizontal exhaust silencer and outlet pipe. FRONT AXLE: ISUZU F027
Type: 4 cylinder, 4 stroke, overhead camshaft, FUEL SYSTEM • Reverse Elliot I-Beam with 2,700 kg capacity.
direct injection diesel. • 30 mm diameter king-pin with ball type
• Rectangular steel fuel tank with 95 litre capacity
Bore x Stroke: 112 mm x 110 mm and 5 litre expansion space. Total 100L thrust bearing.
Displacement: 4,334 cc • Fuel / water separator with warning lamp.
Compression Ratio: 19.0:1
• Single stage fuel filter. REAR AXLE: ISUZU R050
Output Power*: 85 kW @ 3,200 RPM • Banjo type with full floating axle shafts.
Torque*: 285 Nm @ 1,800 RPM • Axle tube size: 106 mm x 106 mm x 6 mm
CLUTCH
Emissions Standard: Euro1/ADR70 • Rated capacity: 5,000 kg
• Hydraulically actuated, 300 mm diameter, dry
* Engine performance standard in DIN (Nett). single plate with 8 coil cushioning springs, single • Single reduction, hypoid gearing with 292 mm
• Integral engine oil cooler. diaphragm pressure spring. Asbestos free clutch ring gear and 4-pinion differential.
• Separate full-flow and bypass engine oil filters. lining material. Total lining area 847cm2. Drive ratio: 5.857:1
• Bosch ‘A’ type fuel injection pump with ‘RLD’
all-speed governor. Quick-start glow plug cold TRANSMISSION: ISUZU MXA-5R
starting aid. • 5 forward speeds including overdrive, 1 reverse
COOLING SYSTEM speed, synchromesh on all gears. P.T.O. opening
• Pressurised cooling system. Tube and corrugated left hand side.
fin type radiator with 2,447 cm2 frontal area. • Gear Ratios:
8-blade, plastic, 430 mm diameter cooling fan 1st 2nd 3rd 4th 5th Rev
with thermatic / viscous type clutch.
4.987:1 2.870:1 1.594:1 Direct 0.728:1 4.774:1
AIR INTAKE SYSTEM
• Maximum Geared Speed: 112 km/h @ 3,400 RPM
• Chassis mounted, cartridge type, 197 mm diameter
air filter. Vertical air intake stack and resonator • Single piece propeller shaft with 82.6 mm
mounted at cabin rear. tube diameter.

CHASSIS SPECIFICATIONS
CHASSIS FRAME BRAKES WHEELS AND TYRES
• [ section rails with cold rivetted cross members • Front and rear drum brakes with dual circuit • 5.50F x 16 JIS 5 stud disc wheels.
forming ladder type frame. Top flange of chassis hydraulic control, vacuum assistance and load • 7.00R16LT 8 P.R. Goodyear G114A tyres.
rail is rivetless. sensing proportioning valve. • Total of 7 wheels and tyres supplied including
• Rail dimensions: Front Drum Diameter: 320 mm 1 spare wheel and tyre assembly.
Web: 216 mm x 6.0 mm Rear Drum Diameter: 320 mm
Flanges:70 mm x 6.0 mm • Slave cylinder / shoe types:
Front: Two leading, manual adjust. ELECTRICAL SYSTEM
• Frame width at chassis end: 850 mm
Rear: Dual two leading, manual adjust. • Batteries: 2 x 12 Volt / 65 Amp-Hour batteries in
• Asbestos free brake linings. series for 24 Volt, negative ground system.
SUSPENSION: Alternator: Hitachi 24 Volt / 50 Amp brushless type.
FRONT • Lining size (per wheel end):
Front: 2 x 307 mm x 75 mm x 9.6 mm • Starting Motor: Hitachi 24 Volt / 4.0 kW reduction
• Alloy steel, multi-leaf springs with fully wrapped Rear: 2 x 307 mm x 75 mm x 9.6 mm geared type.
eye and metalastic bushes. • Rear brake, turn, reverse and marker lamp
Nominal size: 1,300 mm x 70 mm • Electro-vacuum controlled, butterfly type, 70 mm
diameter exhaust brake. Drum parking brake on assemblies and rear registration plate lamp with
• Hydraulic, double acting, telescopic shock transmission output shaft. Control lever floor- additional wiring lengths. Reversing alarm.
absorbers. mounted LHS of driver’s seat.
• Stabiliser bar.
REAR STEERING
• Alloy steel, multileaf, two-stage springs. Fully • Integral power assisted, recirculating ball type
wrapped main spring eyes with metalastic bushes. steering.
Nominal spring lengths: Lube-for-life drag link. Gear driven, vane type oil
Main spring: 1,350 mm x 70 mm pump.
Auxiliary spring: 850 mm x 70 mm
• Gear ratio: 20.9:1
• Hydraulic, double acting, telescopic shock absorbers.
• Turns lock to lock: 4.9
TOWING 750kg (Unbraked trailer)
MODEL RATINGS AND DIMENSIONS CAPACITY 3,500kg (Braked trailer)
MODELS RATINGS TARE MASS # DIMENSIONS (mm) TURNING
CIRCLE
GVM GCM TOTAL FRONT REAR WB OAL FOH ROH CA CE OAW CH FFH RFH KERB
LADEN LADEN TO KERB
NPR 200 Short 4,490kg 7,990kg 2,170kg 1,480kg 690kg 2,765 5,105 1,085 1,255 2,205 3,460 1,995 2,200 685 770 9.8m
NPR 200 Medium 4,490kg 7,990kg 2,240kg 1,500kg 740kg 3,365 5,955 1,085 1,505 2,740 4,345 1,995 2,200 685 770 11.6m
# Estimated mass of cab/chassis with oil, water and fuel tank containing 10 litres of fuel and including spare wheel and tools. 95
CE
O AW 460 CA

CH

FFH RFH

1650 FOH WB ROH

1680 2115 OAL

For further information regarding Cab/Chassis dimensions your Isuzu Dealer can access detailed Body Builders diagrams from the Isuzu Truck Data Manual.