Implementation of Bus Topology in Cisco

Next article icon

Implementation of Hybrid Topology in Cisco

Last Updated : 09 May, 2024

The arrangement of a network that comprises nodes and connecting lines via sender and receiver is referred to as network topology. The combination of two or more topologies in a computer network is called Hybrid Topology. These combined topologies can be a combination of bus topology, mesh topology, ring topology, star topology, and tree topology. To learn about Hybrid Topology refer to the Advantages and Disadvantages of Hybrid Topology article.

In this article, we will see steps to configure and set up Hybrid topology in cisco packet tracer.

Step 1: First, open the cisco packet tracer desktop and select the devices given below:

S.NO	Device	Model Name
1.	PC	PC
2.	Switch	PT-Switch

IP Addressing Table:

S.NO	Device	IPv4 Address	Subnet Mask
1.	pc0	192.168.0.1	255.255.255.0
2.	pc1	192.168.0.2	255.255.255.0
3.	pc2	192.168.0.3	255.255.255.0
4.	pc3	192.168.0.4	255.255.255.0
5.	pc4	192.168.0.5	255.255.255.0
6.	pc5	192.168.0.6	255.255.255.0
7.	pc6	192.168.0.7	255.255.255.0
8.	pc7	192.168.0.8	255.255.255.0
9.	pc8	192.168.0.9	255.255.255.0

Then, create a network topology as shown below the image (Bus, ring, and star topology).
Use an Automatic connecting cable to connect the devices with others.

Step 2: Configure the PCs (hosts) with IPv4 address and Subnet Mask according to the IP addressing table given above.

To assign an IP address in PC0, click on PC0.
Then, go to desktop and IP configuration and there you will find IPv4 configuration.
Add IPv4 address and subnet mask.

Assigning IP address using the ipconfig command.

We can also assign an IP address with the help of a command.
Go to the command terminal of the PC.
Now type ipconfig <IPv4 address><subnet mask><default gateway>(if needed)

example: ipconfig 192.168.0.1 255.255.255.0

Repeat the same procedure with other PCs to configure them thoroughly.

Step 3: Verify the connection by pinging the IP address of any host in PC0.

Use the ping command to verify the connection.
We will check, if we are getting any replies or not.
As we can see here getting replies from a targeted node on both PCs. Hence the connection is verified.

A simulation of the experiment is given below we have sent two PDU packets one targeted from PC0 to PC4 and another targeted from PC3 to PC8.

Output:

Implementation of Bus Topology in Cisco

shadit13064

News

Improve

Article Tags :

Practice Tags :

Cisco

Similar Reads

Implementation of Hybrid Topology in Cisco

The arrangement of a network that comprises nodes and connecting lines via sender and receiver is referred to as network topology. The combination of two or more topologies in a computer network is called Hybrid Topology. These combined topologies can be a combination of bus topology, mesh topology,

Implementation of Bus Topology in Cisco

A bus topology is a network in which nodes are directly linked with a common half-duplex link. A host on a bus topology is called a station. In a bus network, every station will accept all network packets, and these packets generated by each station have equal information priority. A bus network inc

Implementation of Mesh Topology in Cisco

Pre-requisite: Advantages and Disadvantages of Mesh Topology In the mesh topology of networking, each and every device sends its own signal to the other devices that are present in the arrangement of the network.Â Steps to Configure and Setup Ring Topology in Cisco Packet Tracer:Step 1: First, open

Implementation of Tree Topology in Cisco

Pre-Requisite: Advantages and Disadvantages of Tree Topology In the tree topology of networking, the elements and devices are arranged like a tree structure and have branches of connections between the devices connected to each other. To implement tree topology in Cisco there are various steps as fo

Implementation of Ring Topology in Cisco

Ring topology is a kind of arrangement of the network in which every device is linked with two other devices. This makes a circular ring of interconnected devices which gives it its name. Data is usually transmitted in one direction along the ring, known as a unidirectional ring. The data is deliver

EIGRP Implementation in Cisco

The functions of a dynamic routing protocol are the same as a static routing protocol. If the destination is unreachable from a point of routing then the other path can be created to reach the destination. To learn about EIGRP refer to EIGRP fundamentals. Steps to Configure and Verify EIGRP in Cisco

Implementation of RIP Routing in Cisco For Connecting Two Routers

Pre-Requisite: Routing Information Protocol (RIP) Routing Information Protocol (RIP) is an active routing protocol that operates hop count as a routing metric to find the most suitable route between the source and the destination network. It is a distance-vector routing protocol that has an AD value

Implementation of Static Routing in Cisco - 2 Router Connections

Pre-Requisite Types of Routing Static routing is a routing protocol that helps to keep your network organized and to optimize routing performance. It enables the router to assign a specific path to each network segment and to keep track of network changes. This helps to improve network stability and

Implementing Star Topology using Cisco Packet Tracer

A star topology for a Local Area Network (LAN) is one in which each node is connected to a central connection point, such as a hub or switch. Whenever a node tries to connect with another node then the transmission of the message must be happening with the help of the central node. The best part of

OSPF Implementation

OSPF stands for Open Shortest Path First a link-state protocol and as the name itself justifies that it is used to find the best and the optimal pathway between the starting point and the destination target router using its own shortest path first algorithm. It sends hello packets every 10 seconds.