HSPA+ Industrial Router

UR5i v2 Libratum
USER’S MANUAL
 USED SYMBOLS

Used symbols
Danger – Information regarding user safety or potential damage to the router.

Attention – Problems that can arise in specific situations.

Information, notice – Useful tips or information of special interest.

GPL licence
Source codes under GPL licence are available free of charge by sending an email to:
cellularsales@advantech-bb.com.

Advantech B+B SmartWorx s.r.o., Sokolska 71, 562 04 Usti nad Orlici, Czech Republic
Manual Rev. 1 released in CZ, July 25, 2016

i
 CONTENTS

Contents
1 Safety Instruction 2

2 WEEE directive 3

3 Router Description 4

4 Contents of Package 5

5 Router Design 6
5.1 Router versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5.2 Delivery identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.3 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.4 Basic dimensions of the router box . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.4.1 Plastic box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.4.2 Metal box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.5 Mounting recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.6 Removing from the DIN rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.7 Description of the front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.7.1 Status indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.7.2 Power connector PWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.7.3 Antenna connector ANT, DIV (and WIFI) . . . . . . . . . . . . . . . . . . 15
5.7.4 SIM card reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.7.5 Ethernet port (ETH0 and ETH1) . . . . . . . . . . . . . . . . . . . . . . 17
5.7.6 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

6 First Use 19
6.1 Connecting the router before first use . . . . . . . . . . . . . . . . . . . . . . . 19
6.2 Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.3.1 Configuration over web browser . . . . . . . . . . . . . . . . . . . . . . . 20
6.3.2 Configuration over Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . 21

7 Technical Parameters 22
7.1 Basic parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.2 Standards and regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.3 Technical parameters of module . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.4 Technical Parameters of WiFi . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.5 Technical parameters of processor . . . . . . . . . . . . . . . . . . . . . . . . . 24

ii
 CONTENTS

8 Recommended Literature 25

9 Troubleshooting 26
9.1 FAQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

10 Customers Support 28

iii
 LIST OF FIGURES

List of Figures
1 Contents of package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Front panel UR5i v2L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 Front panel UR5i v2L with WiFi . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4 Front panel UR5i v2L SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 Front panel UR5i v2L SL with WiFi . . . . . . . . . . . . . . . . . . . . . . . . . 6
6 Example of the router label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
7 Basic dimensions of plastic box (bottom and front view) . . . . . . . . . . . . . 8
8 Basic dimensions of metal box (bottom and front view) . . . . . . . . . . . . . . 8
9 Space around antennas (plastic) . . . . . . . . . . . . . . . . . . . . . . . . . . 9
10 Space around antennas (metal) . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
11 Cable routing (plastic) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
12 Cable routing (metal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
13 Space in front of connectors (plastic) . . . . . . . . . . . . . . . . . . . . . . . . 10
14 Space in front of connectors (metal) . . . . . . . . . . . . . . . . . . . . . . . . 10
15 Default position of DIN holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
16 Removing from the DIN rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
17 Front panel UR5i v2 Libratum . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
18 Power connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
19 Connection of power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
20 Connecting of the antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
21 Ejected SIM holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
22 Ethernet connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
23 Connection of ethernet cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
24 Router reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
25 Router connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
26 Entering the IP address of the router . . . . . . . . . . . . . . . . . . . . . . . . 20
27 Entering login information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
28 Router web interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

iv
 LIST OF TABLES

List of Tables
1 Router versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Delivery identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Front panel description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4 Status indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5 Connection of power connector . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6 Connection of Ethernet connector . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7 Description of reset and restart router . . . . . . . . . . . . . . . . . . . . . . . 18
8 Basic parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9 Standards and regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10 Technical parameters of module . . . . . . . . . . . . . . . . . . . . . . . . . . 23
11 Technical parameters of WiFi . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
12 Technical parameters of processor . . . . . . . . . . . . . . . . . . . . . . . . . 24

1
 1. SAFETY INSTRUCTION

1. Safety Instruction

Please, observe the following instructions:

• The router must be used in compliance with all applicable international and national laws
and in compliance with any special restrictions regulating the utilization of the router in
prescribed applications and environments.

• To prevent possible injury and damage to appliances and to ensure compliance with
all relevant provisions, use only the original accessories. Unauthorized modifications or
the use of unapproved accessories may result in damage to the router and a breach
of applicable regulations. Unauthorized modifications or use of unapproved accessories
may void the warranty.

• The router can not be opened.

• Turn off the router and disconnect it from power supply before handling of the SIM card.

• Caution! The SIM card could be swallowed by small children.

• Input voltage must not exceed 36 V DC max.

• Do not expose the router to extreme ambient conditions. Protect the router against dust,
moisture and high temperature.

• The router should not be used in locations where flammable and explosive materials
are present, including gas stations, chemical plants, or locations in which explosives
are used. We remind the users of the duty to observe the restrictions concerning the
utilization of radio devices at such places.

• Switch off the router when traveling by plane. Utilization of the router in a plane may
endanger the operation of the plane or interfere with the mobile telephone network, and
may be unlawful. Failure to observe these instructions may result in the suspension
or cancellation of telephone services for the respective client, or, it may result in legal
sanctions; it may also result in both eventualities.

• When using the router in the close proximity of personal medical devices, such as cardiac
pacemakers or hearing aids, you must proceed with heightened caution.

• The router may cause interference when in the close proximity of TV sets, radio receivers
or personal computers.

• It is recommended that you should create an appropriate copy or backup of all the im-
portant settings that are stored in the memory of the device.

2
 2. WEEE DIRECTIVE

2. Product Disposal Instructions

The WEEE (Waste Electrical and Electronic Equipment: 2002/96/EC) directive has been
introduced to ensure that electrical/electronic products are recycled using the best available
recovery techniques to minimize the impact on the environment. This product contains high
quality materials and components which can be recycled. At the end of it’s life this product
MUST NOT be mixed with other commercial waste for disposal. Check the terms and condi-
tions of your supplier for disposal information.

3
 3. ROUTER DESCRIPTION

3. Router Description
HSPA+ router UR5i v2 Libratum is used to wirelessly connect various equipments and
devices via Ethernet interface 10/100 to the internet or intranet. Thanks to high data transfer
speed of up to 14,4 Mbit/s (download) and 5,76 Mbit/s (upload) it is an ideal wireless solution
for traffic and security camera systems, individual computers, LAN networks, automatic teller
machines (ATM) and other self-service terminals, etc.
As a standard, cellular router UR5i v2 Libratum is equipped with two Ethernet 10/100 and
two SIM cards. This wireless router is supplied either in a plastic or metal casing, based on
the requirements of the customer.
Configuration is done via web interface protected by password. The UR5i v2 Libratum
router supports creation of VPN tunnels using technologies IPsec, OpenVPN and L2TP to
ensure safe communication. Web interface provides detail statistics about the 3G router activ-
ities, signal strength, detailed log, etc. Cellular router supports functions: DHCP, NAT, NAT-T,
DynDNS, NTP, VRRP, control by SMS and many other function.
Other diagnostic functions ensuring continuous communication include automatic inspec-
tion of PPP connection offering an automatic restart feature – in case of connection losses, or
hardware watchdog which monitors the status of the router. With the help of a special window
(start up script window) you may insert Linux scripts for various actions. For some applications
the key option to create several different configurations for one HSPA+ wireless router, the so-
called profiles (maximum of 4), and the option to switch between them (for example via SMS,
binary input status, etc.) is essential. Cellular routers UR5i v2 Libratum may automatically
upgrade configuration and firmware from server. This allows mass reconfiguration of many
routers in one time.
The router also supports additional software like R-SeeNet for permanent traffic monitoring
of routers or communication VPN server Digicluster.

Examples of possible applications

• mobile office • telemetric

• fleet management • remote monitoring
• security system • vending and dispatcher machines
• telematic

4
 4. CONTENTS OF PACKAGE

4. Contents of Package
Basic delivered set of router includes:

• router,
• power supply,
• crossover UTP cable,
• up to three external antennas,
• clip for the DIN rail,
• paper start guide.

Figure 1: Contents of package

Temperature range for power supply is reduced to 0 ◦ C to +40 ◦ C!

5
 5. ROUTER DESIGN

5. Router Design
5.1 Router versions
UR5i v2 Libratum router is supplied in the following versions (see table below). All versions
are available in plastic or metal box according to customer requirements.

ETH1
ETH0
SIM1

SIM2
Router versions Router Box

UR5i v2 Libratum Plastic 1x 1x 1x 1x

UR5i v2 Libratum with WiFi Plastic 1x 1x 1x 1x
UR5i v2 Libratum SL Metal 1x 1x 1x 1x
UR5i v2 Libratum SL with WiFi Metal 1x 1x 1x 1x
Table 1: Router versions

Figure 2: Front panel UR5i v2L Figure 4: Front panel UR5i v2L SL

Figure 3: Front panel UR5i v2L with WiFi Figure 5: Front panel UR5i v2L SL with WiFi

6
 5. ROUTER DESIGN

5.2 Delivery identification

Trade name Type name Other

UR5i v2 Libratum UR-5i-v2L Version in the plastic box
UR5i v2 Libratum with WiFi UR-5i-v2L Version with WiFi in the plastic box
UR5i v2 Libratum SL UR-5i-v2L Version in the metal box
UR5i v2 Libratum SL with WiFi UR-5i-v2L Version with WiFi in the metal box
Table 2: Delivery identification

Figure 6: Example of the router label

5.3 Order codes

There are all order codes for this product:

• UR5i v2 Libratum set

includes 2x Ethernet and 2x SIM, supplied in plastic box

• UR5i v2 Libratum SL set

includes 2x Ethernet and 2x SIM, supplied in metal box

• UR5i v2 Libratum WIFI set

includes 2x Ethernet, 2x SIM and 1x WIFI, supplied in plastic box

• UR5i v2 Libratum WIFI SL set

includes 2x Ethernet, 2x SIM and 1x WIFI, supplied in metal box

7
 5. ROUTER DESIGN

5.4 Basic dimensions of the router box

5.4.1 Plastic box

Figure 7: Basic dimensions of plastic box (bottom and front view)

5.4.2 Metal box

Figure 8: Basic dimensions of metal box (bottom and front view)

8
 5. ROUTER DESIGN

5.5 Mounting recommendations

• possibility to be put on a work surface,
• DIN rail EN 60715 with included clip CPD2 (or CKD2 for metal version).

For the most of applications with a built-in router in a switch board it is possible to recognize
two kinds of environments:
• no public and industry environment of low voltage with high interference,
• public environment of low voltage without high interference.

For both of these environments it is possible to mount router to a switch board, the following
there is no need to have examination immunity or issues in connection with EMC according to
EN 60439-1 ed.2:00 + A1:04.

Compliance of EN 60439-1 ed.2:00 + A1:04 specification it is necessary to observe next

assembly of the router to the switch – board:

• For whip antennas we recommend to observe a distance of 6 cm from cables and metal
surfaces on every side due to the elimination of interference. While using an external
antenna except for the switch-board it is necessary to fit a lightening conductor.

• Before mounting a router on sheet-steel we recommend using a "cable" antenna.

Figure 9: Space around antennas (plastic) Figure 10: Space around antennas (metal)

9
 5. ROUTER DESIGN

• For every cables we recommend to bind the bunch, we recommend for this use:

– Length of the bunch (combination of power supply and data cables) can be maxi-
mum 1.5 m. If the length of data cables exceeds 1.5 m or in the event of, the cable
leads towards the switch – board. We recommend installing over – voltage protec-
tors (surge suppressors).
– With data cables they mustn’t carry cables with reticular tension ∼ 230 V/50 Hz.

Figure 11: Cable routing (plastic) Figure 12: Cable routing (metal)

• Sufficient space must be left in front of individual connectors for handling of cables,

Figure 13: Space in front of connectors (plastic) Figure 14: Space in front of connectors (metal)

• For correct function of the router we recommend to use in the switch-board earth-bonding
distribution frame for grounding of power supply of router, data cables and antenna.

10
 5. ROUTER DESIGN

5.6 Removing from the DIN rail

DIN holder is suitable for DIN rail according to EN 60715 standard only. Default position of
CPD2 holder (or CKD2 for metal version), which is used for mounting the router on a DIN rail,
is shown in the following figure:

Figure 15: Default position of DIN holder

For removing from the DIN rail it is necessary to lightly push upward the router so that the
top part of the CPD2 holder (or CKD2 for metal version) hitched to the DIN rail get out of this
rail and then fold out the top part of the router away from the DIN rail.

Figure 16: Removing from the DIN rail

11
 5. ROUTER DESIGN

5.7 Description of the front panel

On the front panel is the following:

Caption Connector Description

PWR 2-pin Connector for the power supply.
ETH0 RJ45 Connector for connection into the local computer network.
ETH1 RJ45 Connector for connection into the local computer network.
ANT SMA Connector for main antenna.
DIV SMA Connector for diversity antenna.
WIFI R-SMA Connector for WIFI antenna. Available only when the
router is equipped with WIFI module.
SIM1 — Holder for the first SIM card.
SIM2 — Holder for the second SIM card.
Table 3: Front panel description

Figure 17: Front panel UR5i v2 Libratum

12
 5. ROUTER DESIGN

5.7.1 Status indication

About router status inform three LED indicators on the front panel. ETH0 and ETH1 ports
have two additional LEDs that provide information about port status.

Caption Color State Description

PWR Green Blinking Router is ready
On Starting of the router
Fast blinking Updating firmware
DAT Red Blinking Communication in progress on radio channel
WAN Yellow 1x flash per sec. Signal strength is from –50 dBm to –69 dBm
2x flash per sec. Signal strength is from –70 dBm to –89 dBm or differ-
ence between neighbours cells is exactly 3 dBm
3x flash per sec. Signal strength is from –90 dBm to –113 dBm or differ-
ence between neighbours cells is smaller than 3 dBm
ETH Green On Selected 100 Mbit/s
Off Selected 10 Mbit/s
ETH Yellow On The network cable is connected
Blinking Data transmission
Off The network cable is not connected
SIM1 Yellow On The first SIM card is active
SIM2 Yellow On The second SIM card is active
Table 4: Status indication

State indication of WAN LED is updated every 10 seconds.

13
 5. ROUTER DESIGN

5.7.2 Power connector PWR

Panel socket 2-pin.
Pin number Signal mark Description
1 VCC(+) Positive pole of DC supply voltage (+9 to +36 V DC)
2 GND(-) Negative pole of DC supply voltage
Table 5: Connection of power connector

Figure 18: Power connector

Power supply for router is required between +9 V to +36 V DC supply. Protection against
reversed polarity without signaling is built into the router.
The power consumption during receiving is 2.3 W. The peak power consumption during
data sending is 5.5 W. However, values of consumption can be increased, if some expansion
port is eqquipped. For correct operation it is necessary that the power source is able to supply
a peak current of 1.2 A.

Circuit example:

Figure 19: Connection of power supply

The positive pole VCC is marked by a red socket on the power.

14
 5. ROUTER DESIGN

5.7.3 Antenna connector ANT, DIV (and WIFI)

Main and diversity antennas are connected to the router using the SMA connector on the
front panel. For UR5i v2 Libratum with WiFi module is also available reverse SMA antenna
connector, through which the WIFI antenna can be connected.

The router can not operate without connected main antenna marked as ANT !

ANT connector is used to connect the main antenna. For connecting the diversity antenna
use the second antenna connector DIV. If WiFi module is equipped on customer’s request,
there is also available WIFI antenna connector for connecting corresponding antenna.

The antenna is connected by screwing this antenna to the SMA connector on the front panel
of the router (see figure below).

Figure 20: Connecting of the antenna

Diversity antenna improves radio features of the router at low signal strength.

15
 5. ROUTER DESIGN

5.7.4 SIM card reader

The SIM card reader for 3 V and 1.8 V SIM cards is placed on the front panel of the router.
For getting the router to work is necessary to insert an activated SIM card with an unblocked
PIN code. The SIM cards might be of different adjusted APN (Access Point Name).

Changing the SIM card:

• Before handling of the SIM card disconnect the router from power supply!
• Press the small yellow button to eject the reader holder.
• Insert the SIM card into the reader holder and slide it in the reader (see figure
below).

Figure 21: Ejected SIM holder

For correct function of mobile network module it is necessary to have both SIM card
holders inserted in the readers when router is running, even if they are empty.
Ejected holder of any SIM card can cause inability to connect the mobile network.

16
 5. ROUTER DESIGN

5.7.5 Ethernet port (ETH0 and ETH1)

Panel socket RJ45.
Pin Signal mark Description Data flow direction
1 TXD+ Transmit Data – positive pole Input/Output
2 TXD- Transmit Data – negative pole Input/Output
3 RXD+ Receive Data – positive pole Input/Output
4 — —
5 — —
6 RXD- Receive Data – negative pole Input/Output
7 — —
8 — —
Table 6: Connection of Ethernet connector

Figure 22: Ethernet connector

ATTENTION! ETH0 and ETH1 ports are not PoE (Power over Ethernet) compatible!

Plug Ethernet cable into the RJ45 connector labeled as ETH0 or ETH1 (see figure below).

Figure 23: Connection of ethernet cable

17
 5. ROUTER DESIGN

5.7.6 Reset
When PWR LED starts flashing on the front panel, it is possible to restore the default con-
figuration of the router by pressing the RST button on the front panel. After pressing this button
the default configuration is restored and then router reboots (green LED will be on).

For pressing the RST button could be used a narrow screwdriver.

Figure 24: Router reset

We recommend backing up configuration of the router (see Configuration manual for v2

routers) because reset of the router sets the configuration to the default state.

It is important to distinguish between reset and reboot the router.

Action Router behavior Invoking events

Reboot Turn off and then turn on router Disconnect and connect the power,
Press the Reboot button in the web
configuration
Reset Restore default configuration and reboot Press RST button
the router

Table 7: Description of reset and restart router

18
 6. FIRST USE

6. First Use
6.1 Connecting the router before first use
Before putting the router into operation it is necessary to connect all components which
are required to run your applications. Don’t forget to insert SIM card.

The router can not operate without connected antenna, SIM card and power supply. If
the antenna is not connected, router can be damaged.

Figure 25: Router connection

19
 6. FIRST USE

6.2 Start
The router is put into operation when the power supply is connected to this router. By
default, the router will automatically start to log on to the default APN. DHCP server will start
to assign addresses for devices on the Ethernet port ETH0. Router behavior can be changed
via the web interface. This is described in detail in the Configuration manual for v2 routers.
The power consumption during receiving is 2.3 W. The peak power consumption during
data sending is 5.5 W. However, values of consumption can be increased, if some expansion
port is eqquipped. For correct operation it is necessary that the power source is able to supply
a peak current of 1.2 A.

6.3 Configuration

Attention! If no SIM card is inserted in the router, it is not possible to operate. Inserted
SIM card must have activated data transmission.

6.3.1 Configuration over web browser

For status monitoring, configuration and administration of the router is available a web
interface which can be accessed by entering the IP address of the router into the web browser.
The default IP address of the router is 192.168.1.1.

Figure 26: Entering the IP address of the router

Configuration may be performed only by the user "root" with default password "root".

Figure 27: Entering login information

20
 6. FIRST USE

After successfully entering login information user gains access to the router via his internet
browser.

Figure 28: Router web interface

A detailed description of the router settings via the Web interface can be found in the document
Configuration manual for v2 routers.

6.3.2 Configuration over Telnet

For status monitoring, configuration and administration of the router can be also used
Telnet. After entering the IP address of the router you will be allowed to configure the router
using commands. The default IP address of the router is 192.168.1.1. Configuration may be
performed only by the user "root" with default password "root".

A detailed description of the router settings via the Telnet can be found in the document Con-
figuration manual for v2 routers.

21
 7. TECHNICAL PARAMETERS

7. Technical Parameters
7.1 Basic parameters
UR5i v2 Libratum
Temperature range Function -40 ◦ C to +75 ◦ C
Storage -40 ◦ C to +85 ◦ C
Humidity Operating 0 to 95 % relative humidity non condensing
Storage 0 to 95 % relative humidity non condensing
Altitude Operating 2000 m / 70 kPa
Degree of protection IP30
Supply voltage 9 to 36 V DC
Consumption Idle 2.3 W
GPRS to 3.5 W (GPRS transmission)
UMTS to 5.5 W (UMTS/HSDPA transmission)
Dimensions Plastic box 51 x 87 x 116 mm (DIN 35 mm)
Metal box 42 x 87 x 113 mm (DIN 35 mm)
Weight UR5i v2 Libratum – 150 g
UR5i v2 Libratum SL – 280 g
Antenna connector 2x SMA – 50 Ohm
1x R-SMA – 50 Ohm (only for WiFi)
User interface ETH0 Ethernet (10/100 Mbit/s)
ETH1 Ethernet (10/100 Mbit/s)
Table 8: Basic parameters

7.2 Standards and regulations

The router complies with the following standards and regulations.

Standards and regulations

Telecom and emission ETSI EN 300 440-2 v1.4.1, ETSI EN 301 511 v9.0.2,
ETSI EN 301 908-1 v6.2.1, ETSI EN 301 908-2 v5.4.1
EMC ETSI EN 301 489-1 v1.9.2, ETSI EN 301 489-3 v1.6.1,
ETSI EN 301 489-24 v1.5.1
Safety EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013,
EN 62311:2008
E8 – EMC for devices E8 homologation number: 10R – 04 7055
in transportation
Table 9: Standards and regulations

22
 7. TECHNICAL PARAMETERS

7.3 Technical parameters of module

HSPA+ module
HSPA+ parameters Bit rate 14,4 Mbps (DL) / 5,76 Mbps (UL)
3GPP rel. 6/7 standard
Data compress 3GPP
UMTS parameters Bit rate 384 kbps (DL) / 384 kbps (UL)
3GPP rel. 4 standard
GPRS/EDGE parameters EDGE bit rate 237 kbps (DL) / 237 kbps∗ (UL)
GPRS bit rate 85,6 kbps (DL) / 85,6 kbps∗ (UL)
Multislot class 12, CS 1 to 4,
3GPP rel. 99/4 standard
Support channels GSM/GPRS/EDGE: Quad band, 850/900/1800/1900 MHz
UMTS/HSDPA/HSUPA/HSPA+: Five band,
800/850/900/1900/2100 MHz
Table 10: Technical parameters of module

∗ Depending on the capabilities of the operator.

7.4 Technical Parameters of WiFi

WiFi
Antenna connector R-SMA – 50 Ohms
Supported WiFi band 2.4 GHz
Standards 802.11b, 802.11g, 802.11n
2.4 GHz supported channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13
RX Sensitivity 11b, 11 Mbps: typ. -85 dBm
11g, 54 Mbps: typ. -70 dBm
(HT20) 11n, MSC7: typ. -66 dBm
(HT40) 11n, MSC7: typ. -62 dBm
TX Output Power 11b, 11 Mbps: min. 18, typ. 19, max. 20 dBm
11g, 54 Mbps: min. 14.5, typ. 16, max. 17.5 dBm
802.11n (HT20): min. 13.5, typ. 15, max. 16.5 dBm
802.11n (HT40): min. 13.5, typ. 15, max. 16.5 dBm
Type of device Access point, station
Table 11: Technical parameters of WiFi

23
 7. TECHNICAL PARAMETERS

7.5 Technical parameters of processor

32b ARM microprocessor
Memory 512 Mb DDR SDRAM
128 Mb FLASH
1 Mb MRAM
Interface Serial interface RS232
Ethernet interface 10/100 Mbit/s
USB 2.0 interface
Table 12: Technical parameters of processor

24
 8. RECOMMENDED LITERATURE

8. Recommended Literature
[1] Advantech B+B SmartWorx: Start guide for v2 routers,
[2] Advantech B+B SmartWorx: Configuration manual for v2 routers,
[3] Advantech B+B SmartWorx: Application note – Programmer guide.

25
 9. TROUBLESHOOTING

9. Troubleshooting
If you can not connect to the router from your PC, your network card may be configured
the way it is not possible to connect to the router. Take one or more of the following steps
to solve the problem:

• Select the communication rate 10 MB/s in the properties of your network card.
• Connect the router to the PC via Switch.
• Connect the router to the PC, start the router first and then start the PC after the
router’s initialization.

9.1 FAQ
- I have NAT enabled. My equipment is not connecting to the network.

• The device’s gateway has to be configured as the router.

- The router resets itself and the Ethernet connection fails.

• The router will not function without an antenna. Keep the antenna as far as possible
from the power supply.

- I can’t access the Web server over NAT.

• The remote HTTP access of the router has to be disabled, the default server ad-
dress has to be your web server and the gateway of the web server has to be the
IP of the router.

- Mobile WAN connection fails. (DAT LED off)

• Check signal power. If the signal power is weak, you will have to use a better an-
tenna. If the neighboring cells have a similar signal strength, you will need to use a
directional antenna. For proper operation, the signal levels have to be in the range
from -50 dBm to -90 dBm.
• It is necessary to set ping, which will check the connection and, in the case of failed
ping, restart connection.

- Mobile WAN connection cannot be established. (DAT LED off)

• Recheck GPRS settings – APN, name, password and IP address.

• Try to enter PIN – verify if the SIM card has the PIN code set.
• In a private APN, switch the DNS server send off.
• Switch the system log on and observe where the error occurs.

26
 9. TROUBLESHOOTING

- Ethernet connection fails or isn’t establishing.

• It is possible to turn auto negotiation off and set a rate and duplex manually on the
Ethernet interface of the router.

- DynDNS doesn’t function.

• With private APN this is not functional.

• If the same IP address is recorded in your canonic name as dynamically assigned
address, it means that the operator is using NAT or firewall.
• Verify NAT using ping to the static server address.
• Verify Firewall accessing remotely to the router’s Web interface.
• The operator may not provide the address of DNS server and without DNS server’s
adress it is impossible to connect to the dyndns.org server. There will be these
messages in the system log:
– DynDNS daemon started
– Error resolving hostname: no such file or directory
– Connect to DynDNS server failed

- L2TP or IPSec isn’t establishing.

• Check the system log for error messages.

- I switched the router to offline mode by SMS message, but the router is in online
mode after restart.

• SMS messages do not change the router configuration. They remain in effect only
until the router is restarted.

- FTP doesn’t function.

• Router doesn’t support active FTP mode. It supports passive mode only.

- RS232 doesn’t function.

• Verify that the router supports RS232 communications. Also verify the RS232 com-
munication settings. To do so, open the router’s configuration menu via the web
browser, select the appropriate expansion port and verify the settings in the config-
uration menu.

27
 10. CUSTOMERS SUPPORT

10. Customers Support

You can find current information about this product on our website:

www.bb-smartcellular.eu

Upkeep-advices:

• The SIM-card must be handled carefully as with a credit card. Don’t bend, don’t scratch
on this and do not expose to static electricity.

• During cleaning of the router do not use aggressive chemicals, solvents and abrasive
cleaners!

Advantech B+B SmartWorx s.r.o. hereby declares that the router narrated in this user’s guide
fits all basic demands of directive 1999/5/EC (R&TTE).

Router fits values of coefficient SAR defined by association ICNIRP and values of "About
protection of health before non-ionized radiation".

Declaration of Conformity was issued and it is possible to find it on the Advan-

tech B+B SmartWorx website (www.bb-smartcellular.eu/download) in respective
product category or is available on request from producer.

28