Klebit 303.
2
Industrial glue for water-resistant Properties of the glue
bonding in accordance with DIN EN 204 Base: PVAC dispersion
Stress Group D 3 Mixing ratio (weight
or volume): Comp. A : Comp.B = 20 : 1
(i.e. 5 % hardener added)
Fields of use Specific weight: Comp. A = approx. 1.10 g/cm³
• Bonding windows and doors Comp. B = approx. 1.13 g/cm³
pH-value: approx. 3.0
• Surface bonding of HPL boards
Colour of glue: white
• Surface bonding during partition and element Colour of mixture: white
manufacture Consistency: medium viscous
• Bonding hard and exotic timbers, e.g. for the Viscosity at 20°C
construction of stairs - Brookfield RVT Sp 6/20 rpm:
• Suitable for veneers 13,000 ± 3,000 mPa·s
• High frequency bonding Pot life: approx. 24 hrs with hardener added
Open time (at 20°C): 6-10 minutes
Advantages Chalk point: approx. +5°C
• As a single component glue - ready for use Identification - Glue: Identification not required
• As a two component glue - for demanding according to the German
requirements Hazardous Substances
Regulations, GefStoffV.
• Suitable for hot and cold bonding (See our safety data sheet)
• Short press times Identification - Hardener:
Identification is required
Properties of the bond according to GefStoffV. Contains
• When used as a single-component glue Isocyanates. Protect hands and
KLEIBERIT Klebit 303.2 meets the eyes! Wash off splashes
immediately with water.
requirements of stress group D3 according to
(See our safety data sheet.)
DIN EN 204 (see test certificate no. 555 27399
issued by the “Fenster Institut Rosenheim”,
dated 28.08.03) Application methods
• When used a two-component glue with 5% • Brush, spatula or glue roller
KLEIBERIT Turbo-Hardener 803.5 added, it • Gluing devices fitted to frame presses and
dovetailing machines
meets the requirements of stress group D4
• Glue spreading machines
(see test report 555 27396/1 issued by the
“Fenster Institut Rosenheim” dated 08.09.03)
Application devices must be made from V2A
• KLEIBERIT Klebit 303.2 has been tested acc.
to WATT91 (test report 555 27399/2 issued by steel or synthetic materials.
the “Fenster Institut Rosenheim”, dated
15.09.03) Application techniques
• High bond strength, also with hard and exotic The materials to be glued must be free from dust,
timbers oil and grease, and be acclimatised.
• Glue line (single-component glue): tough The most favourable working temperature is 18-
elastic, colourless 20° C and the moisture content of the wood should
• Glue line (two-component glue), tough elastic, range between 8-10 % for indoor areas and 10-14
slighty yellow) % for window production. Do not process below
+10° C!
In most cases, single-sided glue application is
sufficient. Double-sided application is
recommended for hard and exotic timbers!
KLEBCHEMIE M. G. Becker GmbH + Co KG • P.O. Box 1204 • D-76353 Weingarten
tel. +49 7244 620 • fax +49 7244 7000 • E-Mail info@kleiberit.com, http://www.kleiberit.com
Slight foaming of the mixture will not affect the glue
Klebit 303.2 quality and can be eliminated by stirring.
Windows and similar frame constructions can be
Application quantity: removed from the press immediately after having
120-130 g/m² for veneer work. been temporarily fastened together with nails. Final
150-200 g/m² when bonding solid wood. bond strength which meets the requirements of
The application quantity is dependent upon the DIN/EN 204 stress groups D3 or D4 will be
structure of the surface and the application devices reached after 7 days.
used.
Open time: Wood and wooden materials are natural products.
6-10 min. Influenced by the region of the world from which
they originate, as well as the differing pre-treatment
The open time is influenced by the quantity of glue methods to which they have been exposed,
applied, absorbability of the materials, temperature isolated cases of discolouration, (e.g. Birch, Cherry
and the moisture content of the wood and air. and Sugar Maple) can occur. The same can
happen when bonding wood which contains tannin
Pot life: approx. 24 hours (e.g. Oak) and when it makes contact with iron
Thoroughly stir in the prescribed amount of (due to an unsuitable pressing plant).
hardener until a good mixture is achieved.
Following expiry of the pot life, any glue remaining
may be used as D3 glue or re-mixed with 5 %
KLEIBERIT Turbo-Hardener 303.2 to attain a D4 Cleaning
bond. Application devices, machines and containers can
be cleaned with water
Pressure: 0.70-1.00 N/mm² for laminated plastics
and laminated wood Packaging
KLEBIT 303.2:
Press times: Plastic hobbock 10 kg net
Joint bonding at 20° C - from 15 min Plastic hobbock 28 kg net
Joint bonding (pre-heated) at 50° C - from 5 min Plastic drum 130 kg net
Joint bonding at 80° C - from 2 min Disposable plastic container 1000 kg net
Surface bonding HPL boards at 20° C - 15-20 min
Surface bonding HPL boards at 50° C - approx. 5 min
Surface bonding at 80° C - 1-2 min KLEIBERIT Turbo Hardener 803.5:
Carton cont. 12 metal bottles each 0.50 kg net
When used as a two component glue, the times Carton cont. 12 metal bottles each 0.7kg net
shown should be increased by approx. 50 %.
Storage
Both components can be stored for approx. 1 year
at 20° C in the original factory sealed containers.
The glue is resistant to frost and temperatures
down to approx. -30° C. Before use, warm to room
temperature and stir well.
EX 0605 - Replaces all previous editions
Waste Disposal Service
Disposal of contents and/or containers should comply with all applicable federal, Our application department may be consulted at any time without obligation. The
state and local regulations. statements made herein are based on our experience gained to date. They are to be
Our containers are made of recyclable material. considered as information without obligation. Please test and establish for yourself
the suitability of our products for your particular purposes. No liability exceeding the
value of our product can be derived from the foregoing statements. This also applies
to the technical consultancy service which is rendered free of charge and without
obligation.
KLEBCHEMIE M. G. Becker GmbH + Co KG • P.O. Box 1204 • D-76353 Weingarten
tel. +49 7244 620 • fax +49 7244 7000 • E-Mail info@kleiberit.com, http://www.kleiberit.com
