BILL OF QUANTITIES

SRNO QTY DESCRIPTION UNIT RATE AMOUNT

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board
having IP-64 protection made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for
internal partitions with necessary supporting angles, flats including cutting, bending, drilling, welding, riveting with internal
partitions & cable alley as per requirements & instruction of engineer-in-charge with erection of supplied switch gears,
busbars, with suitable size of inter connecting PVC copper wire / copper-aluminum strips, rubber grommets, rib, bakelite
control fuses for measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of
hinged doors, handles with locking arrangement and rubber gasket complete. The Panel shall be painted with epoxy
powder coating. (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminimum strips,
meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following
approved manufacturers with following size.(A) The standard companies switch gear shall be used and only manufacturers
at CPRI approved factory and shall be certified by that company whose switch gears are used after fabrication for
beneficial use
66.00 4.3 (i) with 350mm depth Sq.Mtr 0.00
Supplying & erecting IP 55 grade 150 x 90 x 75 cms section pillar fabricated from 14 Gauge thick joint less M.S. Sheet with
angle iron legs 95 cms long made from 40 x 40x 6 mm thick. Jointless M.S. Angle with cable clamps to be burried in ground
to have appropriate erection to work Uniform Until erected with cement concrete foundation and 45 cms high bricks work
finishing with plaster etc. hinged double door with 4" x 6" vision panel covered with Mesh & V. panel overlapping with flap
for meter reading internally supported on both side,
with internal and outside looking arrangement with look and keys in duplicate 40 x 40 x 6 mm M.S. Angle of Two Nos. one is
welded and other with nut and bolt for erecting backlite sheet. Painting the Section Pillar inside and out side with three
tank powder coated paint. section pillar roof should be without joint with water leakage proof & tested as per IP 55 test &
followed by IS 2147 of 1962
67.00 4 Ea. 0.00
Supplying & erecting MINI SECTION PILLAR 75 x 60 x 45 cms fabricated from 16 Gauge thick joint legs M.S. Sheet with angle
iron legs 45 cms long made from 35 x 35 x 5 mm thick. Jointless M.S. Angle with cable clamps to be buried in ground to
have appropriate erection to work Uniform Until erected with cement concrete foundation and 45 cms high bricks work
finishing with plaster etc. hinged double door with 3" x 4" vision panel covered with Mesh & V. panel overlapping with flap
for meter reading internally supported on both side, with internal and outside looking arrangement with look and keys in
duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and other with nut and bolt for erecting bakelite sheet.
Painting the Section Pillar inside and out side with three tank powder coated paint.. Section pillar roof should be without
joint with water leakage proof & tested as per IP 55 test & followed by IS 2147 of 1962
68.00 2 Ea. 0.00
69.00 60 Supplying and erecting bakelite sheet 12mm thick HYLAM make on existing angle iron frame. Kg. 0.00
Supplying and erecting triple pole & neutral 440V/ 500V panel mounting Aluminium Busbars with four equal Nos. of bus
having current density not more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour
insulating tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports
/insulators, main cable socket to each busbar,erected in existing cubical panel with necessary connections.
(A) Suitable for 100 Amp. Capacity
70.00 6 Rn.Mtr 0.00
71.00 3.6 (C) Suitable for 300 Amp. Capacity Rn.Mtr 0.00
Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase AC Supply 500 V on existing panel board with
72.00 14 necessary connections. No 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Supplying and erecting approved make panel mounting type Digital Ammeter having 3 digits LED display, external CT
operated, calibrated for 0 to 1000 Amps suitable to operate on 500 Volt AC , erected on existing panel board with all
73.00 14 connection, wiring etc .with manufacturers calibration certificate. No 0.00
Supplying and erecting approved make panel mounting type Digital Voltmeter having 3 1/2 digits LED display, 0 to 750
AC Volts range erected on existing panel board with all connection, wiring etc .with manufacturers calibration certificate.
74.00 14 No 0.00
Supplying and erecting approved make set of indicator lamps of LED type lamp, lense cover, Bakelite holder complete
75.00 42 erected with necessary connections. No 0.00
Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio 15 VA burden erected in existing CRCA
76.00 42 box duly secured with insulating materials connected to the meter No 0.00
Supplying & erecting bank of all polypropylene condensor (APP type) with standard capacity of 2,3,5,7, 10,12.5 & 15 KVAR
units of P.F. correction for operation on 3 phase 50 c/s, 400 /440V (+ / - 10%) with externally discharging resistance, earthing
termianl & built on angle iron of channel iron frame work and provided with terminal cover box. Complete erected on
77.00 45 provided iron bracket or on floor duly tested by license. KVAR 0.00
Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate battery backup
1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum
switching setup time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Programming switches &
housed in fire proof thermoplastic enclosure & transparent cover erected as required with necessary connection erected
78.00 6 as directed Ea. 0.00
Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar,
neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of
MCBs.(The DBs should be used of same company of MCB to be used).
79.00 6 (N) Three phase 8 way SS Double door for horizontal single phase outgoing Ea. 0.00
80.00 6 (F) Single phase 8 way SS Double door Ea. 0.00
Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V . having normal
current rating up to 250A. with variable thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal
connections & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only Cat III
81.00 3 Ea. 0.00
Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 25 KA. at 415 V,having normal
current rating up to 25 A to 100A. with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all
internal connections & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only Cat III
82.00 12 Ea. 0.00
Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity &
83.00 12 confirms to IS :8828 in existing box having following capacity. (a)32 Amp. Cat.III Ea. 0.00
84.00 12 (b)40 Amp. Cat.III Ea. 0.00
85.00 10 (c)63 Amp. Cat.III Ea. 0.00
Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having breaking capacity 10
86.00 301 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark. Cat.III Ea. 0.00
Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking
87.00 98 capacity & confirms to IS : 8828 in existing box having following capacity (A) 6 to 32 Amp. Cat.III No 0.00
88.00 20 (B) 40 Amp. Cat.III No 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand
capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all
advance feature & do not incorporate any electronic component.for following Max. rating erected as directed. (ii)
89.00 6 40Amps. DP Ea. 0.00
90.00 12 (i) 25 Amps.DP Cat. III Ea. 0.00
Supplying & erecting power contactor for time switch complete erected as per direction Cat III
91.00 6 [D] 4 pole 440V 40 Amp. Ea. 0.00
92.00 5 Plastic enclosure fitted with DIN rail suitable for incorporating Three /Four nos. MCB Ea. 0.00
93.00 20 Sheets steel powder coated enclosure suitable for incorporating One/Two nos. MCB. Ea. 0.00
Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS
PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling
complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC /
Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling
as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.covered with textured/metallic
front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose /
H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories. Cat. III
94.00 231 Ea. 0.00
Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV
grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on
wall/ceiling, complete with earth continuity and necessary connection with primary light with moduler accessories
erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring.with
necessary Lamp holder / ceiling rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories
95.00 228 Ea. 0.00
Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting
base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type
96.00 59 accssories. Cat. III PT. 0.00
Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC
insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/celing complete
with 6A Modular type switch and hum free EME four or more step type electronic fan regulator with separately mounted
and accessories with earth continuity of following type erected on PVC / Metallic box, single mounting base frame
covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected.with necessary ceiling
rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories. Cat. III
97.00 78 PT. 0.00
Providing & erecting Switch board for Computer or electric apparatus consisting of following items in single board
erected on PVC / Metal board with 3 mm thick PC (Polycarbonet) / Acrylic sheet erected as directed 1 no. 6A/16A
universal plug-switch combined. 1 no. 6A/16A universal plug-switch combined. 4 nos. 6A Switch. 4 nos. 6A 5 pin Plug. [B]
98.00 11 For Modular Type Accessories. Cat. III PT. 0.00
Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC
insulated multistrand copper wires, in existing pipe duly erected complete with Modular type switch & 5 pin Plug erected
on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with
following type of accessories. [I] For 6A Plug with 2-1.5 sq.mm Cu. Wire. (a) with medium class Rigid PVC pipe and
99.00 61 accessories. Cat. III PT. 0.00
100.00 16 [II] For 16A Plug with 2-2.5 sq.mm Cu. Wire. (a) with medium class Rigid PVC pipe and accessories. Cat. III PT. 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame
covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer
101.00 11 Incharge. (3) Two Pin/RJ-11 Telephone Socket. [A] For One Gang. Cat.III Ea. 0.00
102.00 11 (8) Modem Jack for Computer Open RJ-45 Ea. 0.00
103.00 10 (4) TV Co-axial Socket outlet. Cat.III Ea. 0.00
104.00 10 (14) 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular MCB Switch Ea. 0.00
Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be
erected concealed in /flushed with wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of
green colour for earth continuity of following size. (a) with medium class Rigid PVC pipe and accessories. (a) 2 wire 1.5 sq.
105.00 2350 mm mtr. 0.00
106.00 750 (b) 2 wire 2.5 sq. mm mtr. 0.00
Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in existing pipe erected with 2.5
sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size. (a) with
107.00 650 medium class Rigid PVC pipe and accessories. (a) 2 wire 4 sq. mm Rmt. 0.00
Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or
ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of
108.00 850 pipes, in approved manner as directed. (b) 25 mm mtr. 0.00
109.00 1850 (c) 32 mm mtr. 0.00
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on
wall with necessary clamps or in existing trench / pipe of following size of cables (B) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm
110.00 75 core) Mtr. 0.00
111.00 325 (H) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core) Mtr. 0.00
112.00 25 (E) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core) Mtr. 0.00
113.00 45 (D) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core) Mtr. 0.00
114.00 1738 (C) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core) Mtr. 0.00
115.00 125 (A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core) Mtr. 0.00
Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on
wall with necessary clamps or in existing trench / pipe of following size of cables.(b) 4 core 6 Sq. mm
116.00 4581 Mtr. 0.00
117.00 435 (c) 4 core 10 Sq. mm Mtr. 0.00
118.00 125 (d) 4 core 16 Sq. mm Mtr. 0.00
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall
with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (a) 3 core 2.5Sq. Mm
119.00 1558 Mtr. 0.00
120.00 650 (a-1) 3 core 4 Sq. mm Mtr. 0.00
121.00 165 (b) 3 core 6 Sq. mm Mtr. 0.00
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall
with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.
(A-1) 4 core 4 Sq. mm
122.00 650 Mtr. 0.00
123.00 125 (B) 4 core 6 Sq. mm Mtr. 0.00
124.00 850 (C) 4 core 10 Sq. mm Mtr. 0.00
125.00 65 (D) 4 core 16 Sq. mm Mtr. 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable
complete with out going tails, insulating tape etc for following size of cables. (B) 3 & 1/2 core 35/50 Sq. mm
126.00 4 Ea. 0.00
127.00 6 (A) 3 & 1/2 / 4 core 25 Sq. mm Ea. 0.00
128.00 12 (C) 3 & 1/2 core 70 Sq. mm Ea. 0.00
129.00 4 (D) 3 & 1/2 core 95 Sq. mm Ea. 0.00
130.00 4 (E) 3 & 1/2 core 120 Sq. mm Ea. 0.00
131.00 4 (H) 3 & 1/2 core 240 Sq. mm Ea. 0.00
Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable
132.00 50 complete with out going tails, insulating tape etc for following size of cables. (b) 2 to 4 core 4 Sq. mm Ea. 0.00
133.00 26 (d) 2 to 4 core 10 Sq. mm Ea. 0.00
134.00 8 (e) 2 to 4 core 16 Sq. mm Ea. 0.00
135.00 656 (c) 2 to 4 core 6 Sq. mm Ea. 0.00
136.00 250 (a) 2 to 4 core 2.5 Sq. mm Ea. 0.00
Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high
pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.
(D) 25 Sq.mm.
137.00 12 Ea. 0.00
138.00 28 (E) 35/50 Sq.mm. Ea. 0.00
139.00 22 (D) 25 Sq.mm. Ea. 0.00
140.00 40 (F) 70 Sq.mm. Ea. 0.00
141.00 12 (G) 95 Sq.mm. Ea. 0.00
142.00 16 (H) 120 Sq.mm. Ea. 0.00
143.00 12 (K) 225 Sq.mm. Ea. 0.00
144.00 38 (C) 16 Sq.mm. Ea. 0.00
145.00 52 (B) 10 Sq.mm Ea. 0.00
146.00 2624 (A) 1.5/ 2.5/4/6 Sq.mm Ea. 0.00
Solderless crimping type Copper lugs conforming to IS suitable for cable of following size evenly crimped with high pressure
tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.
(B) 10 Sq.mm
147.00 60 Ea. 0.00
148.00 150 (A) 1.5/2.5 to 6 Sq.mm Ea. 0.00
149.00 40 (C) 16 Sq.mm. Ea. 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Supply of approved make GRP / FRP Pole having following specifications: GRP Light Pole made by CNC filament winding
machine using thermoset resin polyester/epoxy resin system) having minimum 62% glass content. The pole should be in one
piece and tapered round in shape, having smooth finish and should be totally free from corrosion as well as non
conductive & shock proof Pole should be provided with FRP Anchor Base and it should be heavy duty, or MS Material duly
painted with Epoxy paint. Pole should be flame retardant as per IS 6746. Resin used shall be UV resistance and pigmented.
A highly weather resistant polyurethane coating shall be applied to the pole after applying suitable primer system that
ensures proper adhesion of the paint. Minimum coating thickness shall be 80 to 100 micron. Deflection of the pole shall not
exceed more than 10% of the length of pole for the given load“? Pole should be generally made as per the dimensional
data, performance criteria and some interchangeability features of poles as per standard ANSI C 136.20 latest version or
ASTM D 4923/01 . The size of pole and type of installation are as below .
(3) Suitable for direct grouting & Single arm Bracket.
[B] Overall length of 4 Mtr. Average Thickness: 7mm.
Top/ Bottom OD Dia: 90/130 mm ± 2mm approx. approx. Weight of Pole 18 kg approx.
150.00 66 Ea. 0.00
Supply of approved make GRP / FRP Pole having following specifications: GRP Light Pole made by CNC filament winding
machine using thermoset resin polyester/epoxy resin system) having minimum 62% glass content. The pole should be in one
piece and tapered round in shape, having smooth finish and should be totally free from corrosion as well as non
conductive & shock proof Pole should be provided with FRP Anchor Base and it should be heavy duty, or MS Material duly
painted with Epoxy paint. Pole should be flame retardant as per IS 6746. Resin used shall be UV resistance and pigmented.
A highly weather resistant polyurethane coating shall be applied to the pole after applying suitable primer system that
ensures proper adhesion of the paint. Minimum coating thickness shall be 80 to 100 micron. Deflection of the pole shall not
exceed more than 10% of the length of pole for the given load“? Pole should be generally made as per the dimensional
data, performance criteria and some interchangeability features of poles as per standard ANSI C 136.20 latest version or
ASTM D 4923/01 . The size of pole and type of installation are as below .
(3) Suitable for direct grouting & Single arm Bracket.
[H] Overall length of 7.0 Mtr. Average Thickness: 7.5mm.Top/ Bottom OD Dia: 90/170 mm ± 2mm approx. approx. Weight of
Pole 42 kg approx.
151.00 19 Ea. 0.00
Supply of approved make GRP / FRP Pole having following specifications: GRP Light Pole made by CNC filament winding
machine using thermoset resin polyester/epoxy resin system) having minimum 62% glass content. The pole should be in one
piece and tapered round in shape, having smooth finish and should be totally free from corrosion as well as non
conductive & shock proof Pole should be provided with FRP Anchor Base and it should be heavy duty, or MS Material duly
painted with Epoxy paint. Pole should be flame retardant as per IS 6746. Resin used shall be UV resistance and pigmented.
A highly weather resistant polyurethane coating shall be applied to the pole after applying suitable primer system that
ensures proper adhesion of the paint. Minimum coating thickness shall be 80 to 100 micron. Deflection of the pole shall not
exceed more than 10% of the length of pole for the given load“? Pole should be generally made as per the dimensional
data, performance criteria and some interchangeability features of poles as per standard ANSI C 136.20 latest version or
ASTM D 4923/01 . The size of pole and type of installation are as below .
(4) Suitable for direct grouting & Double Side Arm Bracket.
[C] Overall length of 7.0 Mtr. Average Thickness: 8mm. Top/ Bottom OD Dia: 114/174 mm ± 2mm approx. approx. Weight of
Pole 48 kg approx.
152.00 32 Ea. 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Supplying Steel tubular pole (Swaged) confirming to IS - 2713 (Part-II) 1980. Manufacturing process of steel tubular pole
should be as per IS specification. Basic steel tube should be ISI Marked. Pole should be painted by one coat of Zinc comet
Primer and two coat of Aluminium /approved paint to be erected on / in existing Foundation. The length of poles are as
below.
(D) 10.00 mtr. Long Swaged Steel tubular pole
(i) Pole as per IS code 410-SP-40 with 300 X 300 X 6 mm base plate.(Approximate weight 128 Kg) For burial erection.
(ii) ADD Extra for M.S. Base plate 300 X 300 X 16 mm for pole, mounting on surface of foundation on foundation bolt. with
required stiffeners.
(iii) Add Extra for PU base primer and PU Paint on pole.
153.00 2 Ea. 0.00
Supplying Steel tubular pole (Swaged) confirming to IS - 2713 (Part-II) 1980. Manufacturing process of steel tubular pole
should be as per IS specification. Basic steel tube should be ISI Marked. Pole should be painted by one coat of Zinc comet
Primer and two coat of Aluminium /approved paint to be erected on / in existing Foundation. The length of poles are as
below.
(A) 7.5 mtr. Long Swaged Steel tubular pole
(i) Pole as per IS code 410-SP-40 with 300 X 300 X 6 mm base plate.(Approximate weight 128 Kg) For burial erection.
(ii) ADD Extra for M.S. Base plate 300 X 300 X 16 mm for pole, mounting on surface of foundation on foundation bolt. with
required stiffeners.
(iii) Add Extra for PU base primer and PU Paint on pole.
154.00 15 Ea. 0.00
Providing FRP arm bracket of having 2 sets of suitable SS304 hardware for fixing the brackets & spread of 1.2 Mtr(Suitable
for 89 to 114 mm pole top dia)
155.00 19 (a) Single arm bracket Ea. 0.00
156.00 32 (b) Double arm bracket Ea. 0.00
Providing M-20 / 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of size 45 x
45 x 100 cms. Deep in below ground level with plinth of 45 cms x 45 cms (or 45 cms dia x 45 cms) high upper ground level
157.00 66 with necessary curing and finishing in approved manner. ( for 4 & 6 mtr pole) Ea. 0.00
Providing M-20 / 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of size 60 x
60 x 120 cms. Deep in below ground level with plinth of 45 cms x 45 cms(or 45 cms dia x 45 cms) high upper ground level
with necessary curing and finishing in approved manner. ( for 7.5 & 8/8.5 mtr pole)
158.00 66 Ea. 0.00
Providing M-20 / 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of size 60 x
60 x 150 cms. Deep in below ground level with plinth of 45 cms x 45 cms(or 45 cms dia x 45 cms) high upper ground level
with necessary curing and finishing in approved manner.
159.00 2 ( for 9 & 10 mtr pole) Ea. 0.00
Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop-out approx. 2mm thick box
complete with bakelite connector strip 4way & hinged doors having locking arrangements with mounting clamp with nuts,
bolts & washers suitable for erection on pole with cable clamps& earth bolt of following size of box.( c)150mm x 125mm x
160.00 117 100mm [deep] Ea. 0.00
Making trench in soft soil of suitable width of 90 cms deep for laying cable or locating the fault all over the run and
161.00 6439 backfilling the same and making the surface as normal ground. Mtr. 0.00
Making trench in Hard murum / Tar Road of suitable width of 90 cms or required depth for laying cable or locating the
162.00 550 fault all over the run and back filling the same and making the surface as normal ground. Mtr. 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Drilling the road without breaking the road surface (Asphalt) for laying of cable for feeding power supply by making up to
following size of holes at both ends complete.
163.00 250 (B) Up to 150 mm bore dia Mtr. 0.00
Providing & laying. Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary
connecting accessories of same material at required depth for laying of cable. below ground / road surface for
164.00 5839 enclosing cable and back filling the same to make ground as per original. (A)50 mm dia Mtr. 0.00
Providing & laying. Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary
connecting accessories of same material at required depth for laying of cable. below ground / road surface for
165.00 2360 enclosing cable and back filling the same to make ground as per original. (B)90 mm dia Mtr. 0.00
Providing , erecting , fabricating the M.S. structure as per requirement on site incorporating proper size of M.S. angles, flats,
bars, channels, sections complete with cutting, welding, grinding & finishing duly painted with one coat of redoxide with
erection on site as per direction of engineer in charge with necessary gouting, cementing, plastering & finishing complete.
166.00 165 Kg 0.00
Providing & laying. R.C.C. hume pipe for cable to be laid 90 cms. below ground across the road crossing or on floor with
necessary material in an approved manner and making the ground as per original.
167.00 250 (C) 100 mm dia. mtr 0.00
Providing & laying. R.C.C. hume pipe for cable to be laid 90 cms. below ground across the road crossing or on floor with
necessary material in an approved manner and making the ground as per original.
168.00 150 (B)150 mm dia mtr 0.00
Providing & laying. R.C.C. hume pipe for cable to be laid 90 cms. below ground across the road crossing or on floor with
necessary material in an approved manner and making the ground as per original.
169.00 100 (A) 250 mm dia mtr 0.00
Providing & laying ISI marked Rigid PVC pipe having 6Kg / cm2 (Class-3) to be erected at road crossing on or floor as
directed for laying of cable. The pipes as following size of dia & weight per 6 mtr.
170.00 125 (B) 50 mm Dia. (2.5Kg/6RMT) mtr 0.00
Providing & laying ISI marked Rigid PVC pipe having 6Kg / cm2 (Class-3) to be erected at road crossing on or floor as
directed for laying of cable. The pipes as following size of dia & weight per 6 mtr.
171.00 150 (F) 110 mm Dia. (11.63 Kg/6 RMT) mtr 0.00
Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with
housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and
high U.V. & corrosion resistance with diffuser 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT 3000 K to 6500K,
Uniformity ratio >0.7,
Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 % (A) Tube Light with integral/ non-integral driver (d) 20
172.00 56 Watts, Surge - 4KV,IP-20, 4 feet Cat-lll. Ea. 0.00
Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with
housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and
high U.V. & corrosion resistance with diffuser 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT 3000 K to 6500K,
Uniformity ratio >0.7,
Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 % (A) Tube Light with integral/ non-integral driver (e) 36
173.00 40 Watts, Surge-4 KV, IP-20, 4 feet Cat-lll. Ea. 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with
housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and
high U.V. & corrosion resistance with diffuser 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT 3000 K to 6500K,
Uniformity ratio >0.7,
Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 % © Square/ Circular Surface/Recessed Mounted Downlight
with provision for spring loaded mounting clips complete.(b) 13 Watts, Surge-2 KV, IP-20, 4 feet Cat-lll
174.00 39 Ea. 0.00
Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with
housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and
high U.V. & corrosion resistance with diffuser 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT 3000 K to 6500K,
Uniformity ratio >0.7,
Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 % © Square/ Circular Surface/Recessed Mounted Downlight
175.00 68 with provision for spring loaded mounting clips complete.(b) 15 Watts, Surge-2 KV, IP-20, 4 feet Cat-lll Ea. 0.00
Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with
housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and
high U.V. & corrosion resistance with diffuser 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT 3000 K to 6500K,
Uniformity ratio >0.7,
Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 % © Square/ Circular Surface/Recessed Mounted Downlight
176.00 88 with provision for spring loaded mounting clips complete.© 20 watts, Surge-4 KV Cat-lll Ea. 0.00
Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with
housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and
high U.V. & corrosion resistance with diffuser 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT 3000 K to 6500K,
Uniformity ratio >0.7, Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 %(G) Spot Light , 5W, 425 Lumens, Surge-
177.00 20 2KV (b) 11 Watts Cat-lll Ea. 0.00
Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with
housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and
high U.V. & corrosion resistance with diffuser 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT 3000 K to 6500K,
Uniformity ratio >0.7,
Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 %. LED driver efficiency > 85 %
178.00 74 (I) Mirror Light 5 Watts, wall mounted Ea. 0.00
Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with
housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA polyester powder coated and
high U.V. & corrosion resistance with diffuser 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT 3000 K to 6500K,
Uniformity ratio >0.7,
Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 %. LED driver efficiency > 85 %
' E ) LED Strip Light
179.00 125 (a) Minimum 4.8W per meter (2 wire, IP-65) without Driver complete Cat-lll mtr. 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 1Watt and above
assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminum housing
with smooth finish powder coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses with
company mark/name engraved or embossed
120 to 300 V,Power Factor more than 0.95, THD < 10 %, CCT 5000 K to 5700K,
Uniformity ratio >0.45, Luminaire efficacy> 85 lumens/watt . LED driver efficiency > 85 %.
CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/ BridgeLux (U.S.A.) make LED used for luminaire. ( Each fittings required
LM-79 & LM-80 certificates)
(A) Street Light (IP-65), Surge -4KV
180.00 83 (f) Above 60 watts to 90 watts Cat-lll Ea. 0.00
Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 1Watt and above
assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminum housing
with smooth finish powder coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses with
company mark/name engraved or embossed
120 to 300 V,Power Factor more than 0.95, THD < 10 %, CCT 5000 K to 5700K,
Uniformity ratio >0.45, Luminaire efficacy> 85 lumens/watt . LED driver efficiency > 85 %.
CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/ BridgeLux (U.S.A.) make LED used for luminaire. ( Each fittings required
LM-79 & LM-80 certificates)
(B) Flood Light (IP-65), Surge -4KV
181.00 10 (a) above 40 watts Cat-lll Ea. 0.00
Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 1Watt and above
assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminum housing
with smooth finish powder coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses with
company mark/name engraved or embossed
120 to 300 V,Power Factor more than 0.95, THD < 10 %, CCT 5000 K to 5700K,
Uniformity ratio >0.45, Luminaire efficacy> 85 lumens/watt . LED driver efficiency > 85 %.
CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/ BridgeLux (U.S.A.) make LED used for luminaire. ( Each fittings required
LM-79 & LM-80 certificates)
(B) Flood Light (IP-65), Surge -4KV
182.00 30 (b) 60 Watts Cat-lll Ea. 0.00
Supply, Installation testing and commissioning of 40W LED hanging Light Fitting with Including all hardware and
183.00 20 arrangement of hanging the light Fixture also include any height. Ea. 0.00
Supply, Installation testing and commissioning of 20W LED hanging Light Fitting with Including all hardware and
184.00 16 arrangement of hanging the light Fixture also include any height. Ea. 0.00
Supply, Installation testing and commissioning of 40W LED Decorative Post Top Lamp with Including all hardware and
185.00 66 arrangement of hanging the light Fixture also include any height. Ea. 0.00
186.00 160 Supply, Installation, Testing and Commissioning of 10W LED Up / Down light fixture with all accessories. Ea. 0.00
187.00 30 Supply, Installation, Testing and Commissioning of 20W LED Up / Down light fixture with all accessories. Ea. 0.00
188.00 20 Supply, Installation, Testing and Commissioning of 20W LED Spot light fixture with all accessories. Ea. 0.00
189.00 20 Supply, Installation, Testing and Commissioning of 10W LED Planter light fixture with all accessories. Ea. 0.00
190.00 15 Supply, Installation, Testing and Commissioning of 15W LED outdoor Track light fixture with all accessories. Ea. 0.00
Supply, Installation, Testing and Commissioning of 100W LED outdoor RGB Flood light fixture with all accessories.
191.00 20 Ea. 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Supply, Installation, Testing and Commissioning of 15W LED outdoor Mono Green Spot light fixture with all accessories.
192.00 10 Ea. 0.00
Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing ISI mark with Condenser
230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with aluminium blades with , canopy & 30 cms. down rod
erected with 24/ 0.2, 3 core flexible wire with earthing.(Havells, Orient, Crompton, Anchor, Bajaj,Usha)
193.00 62 nos. 0.00
Supplying and erecting approved make oscillating type bracket fan A.C. 23OV. 50cy/s 400/450 mm sweep wall mounted
with height adjustment and rotary tilting device complete with guard, flexible Core plug top complete erected with lead
194.00 20 wires as directed. Cat.II nos. 0.00
Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square
195.00 43 frame ABS body with inbuilt lowers & square frame. nos. 0.00
Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe
Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron
galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant
ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of
applications.
(c) For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer
System(like Automation, SCADA) i.e independent Earthing in normal soil.
Length of Pipe : 3.00 mtrs
196.00 20 Back filling Compound :2 nos Bags of 25 Kg. Ea. 0.00
Providing and erecting required size Copper strip for earthing of H.T. OCB / ACB/ Transformer, LT pannel board, Motors etc.
197.00 125 using copper clamp. kg 0.00
198.00 10 Providing one bag of 25 Kg. Additional Back Filling Compound (BFC) suitable for safe earthing device. Ea. 0.00
199.00 125 Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 S.W.G. Kg. 0.00
Pipe type earthing having 150 cms.long and 2.5 cms. dia. galvanised iron pipe with coupling and buch burried in specially
200.00 117 prepared earth pit complete with necessary 8 SWG earth wire. Ea. 0.00
Providing and fixing approved make Perforated C type cable tray. Made from pre- galvanized CR sheet steel. The cable
tray should be bended as per IS 2062/1079 . with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc.
erected on existing support as per Specification and as per instruction of engineer in charge...(3)150 X 50 X 1.5 mm Thick
201.00 250 Rmt. 0.00
202.00 350 (5)300 X 50 X 1.5 mm Thick Rmt. 0.00
203.00 125 (2)100 X 50 X 1.5 mm Thick Rmt. 0.00
204.00 375 (1) 50 X 50 X 1.5 mm Thick Rmt. 0.00
205.00 75 (6) 450 X 50 X 1.5 mm Thick Rmt. 0.00
Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp
of 450 C. The outlet temp. of the water should drop by 150C within a hour, The water cooler should be comprising of
hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating, coil, thermostats,
relay etc.complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.
206.00 6 nos. 0.00
Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame, prefilter
housing with 'O' ring presediment filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40
Osg inline type post carbon filter auto low & high pressure switches with following size of storage tank & LPH capacity &
erected as directed with one year comprehensive maintenance guarantee. [C] 50 Ltr / Hr with 250 psi 2 nos booster pump
207.00 6 nos. 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
208.00 2250 Supplying & erecting approved make LAN cable of following size in existing pipe as per direction [C] CAT - 6 Rmt. 0.00
Supplying & erecting Digital / PCM / TDM EPABX System having SMT design, system with flexible universal slots, Inbuilt Auto
attendant facility, Minimum 15 Nos. conference, Analog extension line, Calling GSM, E&M line, PRI / E1 & VOIP program me
through Analog telephone digital key from Ethernet, public address cord, shall have unrestricted simultaneous dialling
facility,
QSIG protocol on PRI, 95 / STD / ISD / Local- Locking ,Class of Service, Quick Dial- Single Digit dialling of any two external
numbers, Once only ring device, Boss/Secretary- Do not Disturb Facility, Power Down Mode, Hot Line, Hot Outward Dialling,
Day Night Mode, Auto Call Back, Barge-in, Call Pick Up & Call Transfer, Call transfer while Ringing. With Voice Guide
System, (DISA), Caller ID (CLI), CLI Base ECF,CLI Base routing Internet Ready Port, External Music Port, Call Budgeting, Call
Most Calculation(ASMDR), DID Direct Inverse Dialling, External Music Input, Fax Homing, Global Directory Printing. with
following capacities.
[C] No of Extension 48, No of Junctions 8, No of expandable ports:128, Operators Console - 01 Compatible: ISDN
209.00 1 nos. 0.00
Supplying & erecting Single line BEETEL / BPL / SONY/ Panasonic or equivalent make push button type Cord Less telephone
210.00 11 instrument. nos. 0.00
Providing & erecting main Distribution (MDF) indoor type, back mounted FRLSame.
211.00 3 (a) Suitable for 10 pair nos. 0.00
Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation twisted in
two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring &
confirming to C-DOT erected in existing pipe.of following size of conductors & nos.of pairs. With necessary connections. (b)
212.00 350 Armoured [Jelly Filled]. 3) Fifty Pairs mtr. 0.00
Supply, Installation, Testing & Commissioning of 16 port Patch panel with integrated cable tie shelf, 19" fastening kit,
labeling field, accepting the snap-in type color coding clips in 8 colors. Material: sub-rack made of sheet steel (DC01A) 1.5
mm, color blue chromatized, screen made of plastic (ABS), halogen-free, color medium gray (NCS 2502-B). Information
Outlet or connectin module should comply with the specification mentioned above Mounting dimensions 14.9 x 19.5 mm,
max. material
213.00 3 thickness 1.6 mm. Ea. 0.00
Supply, Installation, Testing & Commissioning of 24 port Rack Mount LIU loaded Single Mode with Box, SM LC Connnector &
214.00 1 Coupler, Pigtails & other required accessories Ea. 0.00
Supply, Installation, Testing & Commissioning of 1000 Base LX singlemode Tranceiver for L2/L3 switch, Single mode, LC
215.00 1 termination supporting distance upto 2000 mtrs Ea. 0.00
Supply, Installation, Testing & Commissioning of Patch cord 2 Mtr. Cat6 Patch cord for Data (Patch Cord, U/UTP Cat.6,
216.00 50 length 2.0 m) Ea. 0.00
Supply, Installation, Testing & Commissioning of Network rack Model :- Wall Mounting type 6U w600mm * d600mm with 6U
Glass door , 2U standard rack mount power distribution unit with 6 Nos. X 5 Amp 5 Pin 230 Volts AC, Inlet Plug type 6A Indian
Round Pin- PDU Rating 8A- 2Sets , Cantilever shelf/type2/1U , Horizontal cable Manager /1U/Loop , Fan as per required
217.00 3 CFM. Ea. 0.00
Supply, Installation, Testing & Commissioning of 6-core Fiber Outside Lan Cable - Corrugated Steel tape Armored, Loose-
218.00 2450 tube, Gel-filled, 9/125 SM OS2 mtr. 0.00
Supply, Installation, Testing & Commissioning of 24F, 1U, SC SM OS2, Loaded with Pigtails, Splice tray, adapter & splice
219.00 20 protectors. (LIU) nos 0.00
Supply, Installation, Testing & Comissioning of 2 MP IP ExIR Dome, H.265+ H.265+, H.264+( MP/HP/BP)/MJPEG, 2 MP
1920x1080P @25/30fps, Super 100dB WDR, 3DNR, ROI, Corridor, HLC/BLC, etc., Dual filter ICR, 2.8MM@104° Angle, up to
220.00 22 30Mtr IR, PoE/12VDC, Protection IP66, TVS 4KV, Lighting 1KV nos 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Supply, Installation, Testing & Comissioning of 2 MP IP ExIR Bullet, H.265+ H.265+, H.264+, MP/HP/BP, MJPEG, 2 MP 1920x1080P
@25/30fps, Super 100dB WDR, 3DNR, ROI, Corridor, HLC/BLC, etc., Dual filter ICR, 4.0MM@89° Angle, up to 30Mtr IR,
221.00 58 Protection IP67, TVS 4KV, Lighting 1KV, Hybrid(Metal+Plastic) enclosure, 3 Axis bracket nos 0.00
Supply, Installation, Testing & Comissioning of 2 MP IP IR Varifocal Bullet (Motorized, SD, Audio, IP67)
H.265+, H.264+( MP/HP/BP)/MJPEG, 3IVA(Tripwire, Perimeter), 2 MP 1920x1080P @25/30fps, True 120dB WDR, 3DNR, ROI, etc.,
2.8 ~ 12.0mm Motorized Auto-focus & Iris, up to 50 Mtr IR, Audio in/out, SD Card slot(128Gb), USB Slot, Alarm In, PoE, 12VDC,
222.00 16 Protection IP67, TVS 4KV, Lighting 1KV, 3 Axis bracket nos 0.00
Supply, Installation, Testing & Comissioning of 40CH Intelligent Embedded UltraHD NVR 40CH @up to 4K(12MP) @25/30fps,
Live Max.40CH @Single screen/ 16CH Sync.Play, All 40CH @IVA Processing(iCRYS IPC), 560M bandwidth, Smart record &
Search, ANR, HDD Grouping &Quota, Onvif/RTSP, P2P/DDNS, H.265+/H.265/ H.264+, Dual Stream, 2xRJ-45(1G) /Audio
In/Out(2-Way), 1CH Alarm Out, HDMI@4K, VGA @1080P, Max. 32TB by 4HDD, 12V DC, 1.5U metal casing
223.00 3 nos 0.00
Supply, Installation, Testing & Comissioning of 2 MP IP IR PTZ (0.002Lux) 20X Optical & 16X Digital, Starlight 0.002lux,
1920x1080P@25/30fps, 720P@50fps, H.265+, H.264, MJPEG, Triple stream, 10 IVA(Double Tripwire, Crowd, Perimeter), Super
120dB WDR, 3DNR, ROI, BL/HLC, etc., -16 tilt, 3D Positioning, 500 Preset, SDCard, Audio in/out, Alram in/out, up to 150mtr IR
range, PoE+, 12VDC, Protection TVS 6KV, Lightining 2KV, IP66 Metal Enclosure (bracket optional)
224.00 5 nos 0.00
225.00 10 Supply, Installation, Testing & Comissioning of 6TB HDD. nos 0.00
226.00 2 Supply, Installation, Testing & Comissioning of Prosafe 16 Port 10/100/1000 PoE+ Switch Power Budget 76 Watts. nos 0.00
Supply, Installation, Testing & Comissioning of Prosafe 8 Port 10/100/1000 PoE with 2SFP Smart Managed Layer 2 Switch - 46
227.00 24 Watts power Budget nos 0.00
Supply, Installation, Testing & Commissioning of 12 port Rack Mount LIU loaded Single Mode with Box, SM LC Connnector &
228.00 24 Coupler, Pigtails & other required accessories Ea. 0.00
229.00 23 Supply, Installation, Testing & Comissioning of 4U Rack outdoor weatherproof Pole Mount Standard Rack. Ea. 0.00
230.00 5 Supply, Installation, Testing & Comissioning of 9U Rack indoor RACK (600 X 800 X 1136) for Mount NVR Ea. 0.00
231.00 2250 Supply, Installation, Testing & Comissioning of armoured Cat-06 cable Mtr 0.00
Supply, Installation, Testing & Comissioning of 10/100/1000M, MM,Dual Fiber, 2 KM, SC Connector, 1310nm External Power
232.00 46 Supply media converter Ea. 0.00
233.00 46 Supply, Installation, Testing & Comissioning of SC to Sc Patch cord. Ea. 0.00
Supply installation and testing of Computer : Core I 3 Processor with 1 GB graphics card, 1 tb HDD, 4 GB ram,
234.00 3 keyboard,mouse. nos. 0.00
235.00 3 Supply & erecting 42"/40" Full HD LED Television with necessary wall stand with all necessary and assessors. nos. 0.00
Supplying and erecting Flexible PVC insulated multistrand multicore 1.1 kv grade ISI marked copper wires of following size
to be erected as directed.
236.00 2350 e) 1.50 Sq.mm 3 core round PVC sheathed Rmt. 0.00
Supply, Installation, Testing & Comissioning of Horn speaker.
Power taps (100 V line): 30 W (333 ohm) / 15 W (666 ohm) / 7.5 W (1k3 ohm) / 3 W (3k3 ohm) / 1 W (10 kohm). Power taps (70
V line): 15 W (326 ohm) / 7,5 W (653 ohm) / 3,75 W (1k3 ohm) / 1,5 W (3k2 ohm) / 0,5 W (9k8 ohm). Power taps (25 V line): 30
W (83 ohm). Frequency response: 250 Hz - 16 kHz. Sensitivity (1W/1m): 93 dB.
237.00 200 Max. SPL.: 107 dB. IP range: IP 66. Material (housing): ABS plastic. Ea. 0.00
Supply, Installation, Testing & Comissioning of 4-channel, class-D installation amplifier with 500W per output. It is suitable for
both 70/100V line installations (selectable through dip-switches). Each channel has its own volume control and LED
indicators (signal, clip and protection). thermal, ultrasonic and RF. The input and output connections are made through
238.00 3 Euroblocks, and it is 1HU for 19'' standard racks. Ea. 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Supply, Installation, Testing & Comissioning of mixer that features 6 Mic/Line channels and 3 stereo channels, with 3 band
equalizer and stereo Master output, Rec stereo unbalanced output. First channel priority of MIC/LINE with Talkover
adjustment. 3 band equalizer. DC 24 V secondary power supply connexion (emergency, back-up).
239.00 1 Ea. 0.00
Supply, Installation, Testing & Comissioning of Gooseneck Microphone Microphone volume and chime separately
adjustable. Chime frequency range: 440-659 Hz. Unidirectional dynamic pattern. Unbalanced jack 1/4" audio output.
Adjustable volume level. ON - OFF switch. Supply: DC 12V with external supplier (included). Impedance: 1000 ohm.
240.00 1 Frequency response: 80 - 12 kHz. Sensitivity: -63 dB. Ea. 0.00
Supply, Installation, Testing & Comissioning of Start sequencer and 8 output power distributor. Individual On/Off switch for
each channel. Bypass function.LED indicator for each channel. Link input for interconnection between several units.
Additional main supply for small device connection.Protections from overloads with 63 A circuit breaker.
241.00 1 Ea. 0.00
Supply, Installation, Testing & Comissioning of Screen Size 55-inch Aspect Ratio 16:9 Backlight Scanning 100Hz
Resolution 1920 x 1080 pixels Viewing Angle 178°/178° TERMINAL VIDEO I RCA X 1 AUDIO IN (L/R) RCA Pin Type X 2 HDMI IN
HDMI 1.4 X 3 ,USB Input USB 2.0 X 2 ,RS232C Yes ,HDMI CEC Yes VGA IN Yes PC AUDIO IN Yes (1) (Share with ACGENERAL
242.00 1 Power Requirements AC 110~240V,50/60H Ea. 0.00
Supply, Installation, Testing & Comissioning of 2-way passive loudspeaker. IP protection: 65 Components: 5 ¼ "woofer + 0.5"
TWT. Power (100 V line): 16 W (625 ohm) / 8 W (1k25 ohm) / 4 W (2k5 ohm) / 2 W (5 k). Power (70 V line): 8 W (612 ohm) / 4 W
(1k22 ohm) / 2 W (2k45 ohm) / 1 W (4k9 kOhm). Power (8 ohm): 40 W AES//150 W peak @ 8 ohm. Input Connector:
243.00 8 Euroblock. Sensitivity (1W/1m): 88 dB.Max SPL: 100 dB. Ea. 0.00
Supply, Installation, Testing & Comissioning of power amplifier for low impedance installations, 4 x 230W @ 2ohm 4 x 150W
@ 4 ohm 4 x 90W @ 8 ohm. Output Power (Bridge): 400W @ 4 ohm 310W @ 8 ohm. Inputs (Impedance/Sensitivity): 20k ohm /
1 V / 0±1 dBu.Frequency Response (stereo mode): 20 Hz - 20 kHz -3dB. Frequency Response (sub mode): 20 Hz - (50 Hz - 250
244.00 1 Hz) -3dB. S/N Ratio: >96 dB. Ea. 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Supplying and erecting, commissioning and testing diesel generating set having continuous rating, 3 phase, 415 volts, 50
cycles A.C. supply comprising of a totally enclosed air/water cooled diesel engine with multi-cylinders developing suitable
BHP not less than following capacity at 1500 RPM with 10% overload for one hour in 24 hours with standard accessories like
fly wheel, lubricating oil cooler, "A" class governor, heavy duty fuel wheel and lubricating oil filter, oil bath air filler,
lubricating oil pressure gauge, end exhaust manifold, standard set of tools with adjustable spanners, screw drivers, feeder
gauge, cylinder head to cover, joint cylinder head to exhaust, element lube oil filter, 12/24 volts electric starting equipment
complete with standard battery, dynamo, cut-outs, ammeter, necessary wiring, pressure gauge, starter etc and heavy duty
Residential type exhaust silencer and vertical hot air duct both logged with asbestos rope, save oil trays, exhaust piping of
required length, standard wall/floor mounted fuel with level indicator and piping and drip proof alternator, self excited,
self regulated, screen protected, with excitation system, capable of delivering the rated system output at 415 volts, 3
phase, 0.8 PF, 50 Hz, 4 wire, running at 1500 RPM, conforming to IS-4722- 1968 with voltage regulation +/- 5% of rated
voltage from no load to full load. Both the engine and alternator fitted on a common fabricated steel base plate with
antivibration mounting engine and alternator both connected to each other by flexible flange coupling and with
floor/wall mounted control panel box comprising of voltmeter ammeter, selector switches, ACB / MCCB / MCB of
adequate capacity, indicator lamps duly wired with HRC fuses. The alternator & control panel shall be connected with
provided suitable capacity armoured cable and complete with Acoustic enclosure (canopy) made out of 18 SWG CRCA
Sheet, sound absorbing material Rockwool of 64 density & 100 mm thick conforming to IS:8183 The resin bonded rockwool
covered from inside the canopy by perforated sheet with 3/4 mm holes, sound level not more than 75 dB at a distance of 1
mtr, as per PVCT norms. Erection, commissioning and satisfactory testing as per requirement with first filling of fuel, oil, etc.
with guarantee of complete system for One year. & with obtaining all necessary certificate from Electrical Inspector. The
Capacity and Ratings of DG sets are as below.
(P)Continuous rating of 200 KVA ,BHP not less than 254 BHP

245.00 1 Ea. 0.00

Providing & erecting approved make AMF control panel suitable for following size of 3 phase, 415 V., 50 cycles, A.C. diesel
generating set complete of scope as detailed below:
1) Power module: A pair of electromechanically interlocked contactors (for mains & generator) Overload relay for
generator contactor Neutral contactor for mains and generator Power socket for connections.
2) Control and metering module: Line voltage monitor. Generator voltage monitor Ammeter 3 items attempt start facility.
Air circuit breakers/MCB/MCCB of suitable rating for auto/manual operation. Auto/manual switch. Emergency stop push
buttons. Manual start push button. frequency meter. Engine hour meter. Two earthing studs.
3) Protection module: The engine shutdown in the unlikely event of Low lube oil pressure High cylinder head temperature. V
belt failure.
4) Indicators with alarm Load on generator.
5) Indicators Load on mains Engine fails to start . Emergency stop battery charger.
The AMF Panel of following capacity
(D) AMF Control Panel for200 KVA/250 KVA3 phase DG Set
246.00 1 Ea. 0.00
Providing and erecting approved make Cassettee type split air-conditioning unit consisting of condensing unit with fan
motor, hermetically sealed scroll/rotary compressor with accessories etc. duly connected separately erected evaporating
unit and blower motor with its accessories by means of proper insulated copper tubing (Cost includes Remote Control)
Daikin, Mitsubishi or O-General
297.00 48 4.0 ton capacity nos 0.00
 BILL OF QUANTITIES
SRNO QTY DESCRIPTION UNIT RATE AMOUNT
Installation charge for ac
298.00 48.00 For, Cassette Unit Nos 0.00
Charges for the refrigerant piping For Single phase Cassette A.C. The piping should be soft, copper tubing with insulation up
299.00 480.00 to 4 TR capacity Rmt 0.00
300.00 600.00 Supplying & erecting unarmoured cable to be erected as directed of following size. 2c X 2.5 sqmm Rmt 0.00
301.00 320.00 Rigid PVC drain pipe of 10 Kg/cm2. rating with 9 mm thk.nitrile rubber insulation. Rmt 0.00
Supplying & Installing M.S. powder coated standard type stand mounting for outdoor unit of Cassette A.C. up to 4 TR
302.00 48.00 Capacity, erected with necessary hardware materials as directed. Nos 0.00
303.00 4.00 Miscelleneous work(Fabrication Work) lot 0.00
304.00 4.00 RCC Core Cutting Wall/beam/slab (IF REQUIRED) Nos 0.00
305.00 4.00 Civil Work (EXTRA IF REQUIRED) lot 0.00
306.00 1.00 Signages JOB 0.00
0.00