AL ZUBEIR HOSPITAL (200 bed) Project

SECTION - PLUMBING FIXTURES

PART 1 - GENERAL

1.1 SUMMARY

A. Section Includes:

1. Water closets
2. Urinals
3. Lavatories
4. Sinks
5. Showers
6. Mop receptors
7. Electric water coolers
8. Showers
9. Hydrants
10. Safety equipment
11. Miscellaneous fixtures

1.2 QUALITY ASSURANCE

A. Water Conservation: Comply with the applicable provisions and recommendations of the
International Plumbing Code 2006

1.3 RELATED DOCUMENTS

A. Section 22 05 01: Plumbing General Provisions

B. Section 22 05 29: Supports, Hangers, Anchors and Sleeves

C. Section 22 11 10: Piping and Accessories

1.4 MAINTENANCE

A. Extra Materials:

1. Loose Key Handles: Provide and deliver to Owner at least 10 loose key handles for
lavatory supplies and wall hydrants and yard hydrants. Obtain receipt and submit to
Architect.
2. Spare Flush Valves: Provide and deliver to Owner (2) spare flush valves of each type
used. Obtain receipt and submit to Architect.

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-1
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

PART 2 - PRODUCTS

2.1 ACCEPTABLE MANUFACTURERS

A. Vitreous China Fixtures: American Standard, Kohler, TOTO, Sloan

B. Flush Valves: Sloan Valve, TOTO, Zurn

C. Closet Seats: Olsonite, Beneke, Church, Bemis

D. Carriers: Zurn, Josam, J.R. Smith

E. Stainless Steel Sinks: Elkay, Just

F. Enameled Cast Iron Fixtures: Kohler, American Standard

G. Faucets: Chicago Faucet, Kohler, American Standard, Moen, Speakman, Symmons, T & S
Brass

H. Traps, Stops, Supplies, Drains and Strainers: McGuire, Dearborn

I. Drain and Supply Insulation: McGuire, Truebro

J. Hose Bibbs, Wall Hydrants: Chicago Faucet, J.R. Smith, Woodford, Zurn

K. Showers: Symmons, Bradley

L. Electric Water Coolers: Filtrine, Halsey-Taylor, Haws, Elkay

M. Safety Equipment: Speakman, Haws, Bradley

2.2 WATER CLOSETS

A. General Characteristics:

1. Vitreous China: Unmarked, true and level, clear, smooth and bright. Warranted not to
craze, color or scale.
2. Trap ways no less than 57 millimeters to 54 millimeters [2¼ inches to 2⅛ inches] in
diameter and fully glazed.
3. Water surface area no less than 250 millimeters x 300 millimeters [10 inches x 12
inches].
4. 100 percent factory tested for hydraulic performance, and trap seal depth, meeting or
exceeding ANSI/ASME Standard A112.19.2 and A112.19.6, CAN/CSA B45 and a
minimum ball pass diameter of 50 millimeters [2 inches].
5. Fixture dimensions conforming to ANSI Standard A112.19.2.

B. Water Closet WC-1: Wall Hung, Flush Valve – Operates at [30 psi]:

1. Bowl: vitreous china, white, wall hung, elongated, direct-fed siphon jet action, 38
millimeters [1 ½ -inch] back spud inlet, designed for 14.2 liters per flush [1.1 gallon flush];
“WETS – 2052.1101” by Sloan.

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-2
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

2. Flush Valve: 4.2 liters per flush [1.1 gallon per flush], battery powered sensor operated,
chrome plated die cast metal cover assembly with tempered glass window, Courtesy
flush over-ride buttons, (4) size AA batteries, exposed diaphragm type, semi-red brass
valve body, adjustable tailpiece, sweat solder adaptor kit, skirted high back pressure
vacuum breaker, chloramine resistant rubber compound for stop seat and vacuum,
chrome plated cast brass wall flange with set screw, 23 millimeters [1-inch] screwdriver
stop, vandal resistant free spinning stop valve cap, seat bumper on angle stop (YO), with
72-hour sentinel flush; “Royal No. ECOS 8111-1.1 by Sloan
3. Seat: Open front, elongated, white, heavy weight solid plastic, no cover, integrally molded
bumper, stainless steel pintles, concealed check hinge;
4. Support: Adjustable type no hub cast iron carrier with rear anchor foot assemble and
nipple length suitable for wall thickness and applicable fitting styles and patterns; i.e.,
right hand, left hand, single, back to back, vertical, horizontal, standard barrel, and long
barrel; “Series 100 and Series 200-M51” by J.R. Smith or with 50 millimeters [2-inch]
auxiliary no-hub inlet where appropriate for other plumbing fixture vertical pipe
connections; “Series 209 or Series 219 – M51” by J.R. Smith.

C. Water Closet WC-2 ADA Compliant Installation:

1. Bowl: vitreous china, white, wall hung, elongated, direct-fed siphon jet action, 38
millimeters [1 ½ -inch] back spud inlet, designed for 4.2 liters per flush [1.1 gallon flush];
“WETS-2052.1101” by Sloan.
2. Flush Valve: 4.2 liters per flush [1.1 gallon] per flush, battery powered sensor operated,
chrome plated die cast metal cover assembly with tempered glass window, Courtesy
flush over-ride buttons, (4) size AA batteries, exposed diaphragm type, semi-red brass
valve body, adjustable tailpiece, sweat solder adaptor kit, skirted high back pressure
vacuum breaker, chloramine resistant rubber compound for stop seat and vacuum,
chrome plated cast brass wall flange with set screw, 25 millimeters [1-inch] screwdriver
stop, vandal resistant free spinning stop valve cap, seat bumper on angle stop (YO), with
72-hour sentinel flush; “Royal No. ECOS 8111-1.1 by Sloan
3. Seat: Open front, elongated, white, heavy weight solid plastic, no cover, integrally molded
bumper, stainless steel pintles, concealed check hinge;
4. Support: Adjustable type no hub cast iron carrier with rear anchor foot assemble and
nipple length suitable for wall thickness and applicable fitting styles and patterns; i.e.,
right hand, left hand, single, back to back, vertical, horizontal, standard barrel, and long
barrel; “Series 100 and Series 200-M51” by J.R. Smith or with 50 millimeters [2-inch]
auxiliary no-hub inlet where appropriate for other plumbing fixture vertical pipe
connections; “Series 209 or Series 219 – M51” by J.R. Smith.

D. Water Closet WC-3:

1. Ceramic, without fender, with trapway size 610 x 450 x 315 millimeters, gravity-fed
flushing system, built in platform.

2.3 URINALS

A. General Characteristics: Fixture dimensions conforming to ANSI/ASME Standard A112.19.2.

and A112.19.6.

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-3
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

B. Urinal UR –1, UR-2: High Efficiency Washdown, ADA Compliant Installation:

1. Urinal: Vitreous china, white, wall hung, 19 millimeters [¾-inch] back spud inlet, washout,
integral flushing rim, 356 millimeters [14-inch] extended front; “WEUS-1005.1001-.05” by
Sloan
2. Flush Valve: 2 liters per flush [0.5 gallon] per flush, battery powered sensor operated,
chrome plated die cast metal cover assembly with tempered glass window, (4) size AA
batteries, beam deflector, exposed diaphragm type, semi-red brass valve body,
adjustable tailpiece, sweat odor adaptor kit, skirted high back pressure vacuum breaker,
chloramine resistant rubber compound for stop seat and vacuum, chrome plated cast
brass wall plate with set screw, 19 millimeters [¾-inch] screwdriver stop, vandal resistant
free spinning stop valve cap, with 72-hour sentinel flush; “Royal No. ECOS 8186-0.5 by
Sloan.
3. Support: 32 millimeters [1¼-inch] diameter uprights welded to 100 millimeters [4-inch]
square steel floor anchor plates with top and bottom fixture bearing and fixture hangers
sized to meet plumbing fixture rough-in dimensions and provided with bearing studs
lengths allow floor anchor plates to be installed within plumbing chase behind masonry
walls; “No. 644” by J.R. Smith.

2.4 LAVATORIES

A. General Characteristics:

1. Faucet:

a. Lead-free brass materials and construction, U.L. listed certifying conformance with
NSF Standard 61, Section 9 test protocol for Residential/Drinking Water Faucets.
b. Operating cartridges: Compression type that closes with water pressure or a
ceramic disc type.

2. Vitreous China: Unmarked, true and level, clear, smooth and bright. Warranted not to
craze, color or scale.
3. “P” Traps and water supplies at lavatories shall be insulated in accordance with ADA
guidelines.

B. Lavatory L-1: Wall Hung

1. Basin: Vitreous china, white, wall hung, 533 millimeters x 381 millimeters [21 inches long
x 15 inches] wide rectangular, rimless, for mounting under counter; “Model No.1402” by
Decolav.
2. Faucet: Chrome plated cast brass, (4) size AA batteries, automatic infrared sensor,
single hole, vandal resistant, 2 liters per minute [0.5 gallon per minute], “Model No. 590-
LGHGMHDF” by Delta. Faucets shall be battery type for all restrooms (RP32508
Transformer and RP32494 Converter).
3. Supply Kit: Chrome plated heavy pattern brass stops with full turn brass stem, chlorine
and chloramines resistant replaceable washers, certified to 14 bar [200 psi] line pressure,
“Premier Line” by McGuire with following features:

a. Chrome plated copper risers.

b. Escutcheon flange.
c. Inlet: 13 millimeters [½ inch].
d. Outlet: 13 millimeters [½ inch].
e. Handle: Key, Wheel.

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-4
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

f. 13 millimeters [½-inch] Chrome plated brass supply tube from female 13

millimeters [½-inch] IPS female water supply rough in to stop valve inlet.

4. Drain: Chrome plated drain assembly with cast brass, open grid strainer, 17-gauge, 32
millimeters [1¼-inch] O.D. tailpiece; “155-A” by McGuire.
5. Trap:

a. Standard: 32 millimeters x 38 millimeters [1¼-inch x 1½-inch] “P” Trap chrome

plated cast brass “P” Trap body, with 17-gauge seamless tubular wall bend, cast
brass slip nuts or flange; “Premier Line 8902C” by McGuire.
b. Heavy Duty Vandal Resistant: 32 millimeters x 38 millimeters [1¼-inch x 1½-inch]
chrome plated cast body J-Bend trap with 17-gauge wall bend, vandal resistant
construction guaranteed to withstand 407 N-m [300 ft/lb] horizontal or vertical blow,
and chrome plated cast brass set screw wall flange; “No. V8902CNC” by McGuire.

6. Piping Insulation: White, seamless and antimicrobial closed cell vinyl insulation systems,
conforming to ADA article 4.19.4, BOCA 1203.4, covering hot and cold angle stops and
water supplies, lavatory drain and “P” Trap assembly; secured without exposed plastic
ties; “No. 102” by Truebro, “ProWrap” by McGuire.
7. Support: 25 millimeters x 76 millimeters [1-inch x 3-inch] rectangular steel tubing uprights
welded to 102 millimeters [4-inch] square steel floor anchor plates with concealed arms,
alignment bar, lock nuts, leveling screws, and fixture locking device sized to meet
plumbing fixture rough-in dimensions and provided with extension adaptor of length to
allow floor anchor plates to be installed within plumbing chase behind masonry walls;
“No. 700-M31” by J.R. Smith.

C. Lavatory L-2 Mounting Under Counter:

1. Basin: Vitreous china, white, mounted under counter, 482 millimeters long x 381
millimeters wide [19 inches long x 15 inches wide] circulat, 102 millimeters [4-inch] center
hole punch, concealed front overflow, self-draining deck area with contoured back and
side splash shields, for concealed arm support;
2. L-2 Faucet: Chrome plated cast brass, infrared sensor, 102 millimeters [4-inch] center
set, vandal resistant, 2 liters per minute [0.5 gallon per minute], “Model No. 591-
LGHGMHDF” by Delta. Faucets shall be battery type for all restrooms and hardwired for
multi-stall restrooms; (RP32508 Transformer and RP32494 Converter).
3. L-3 Faucet: Chrome plated cast brass, cross handle manual, 22.9 cm (9”) 90° spout from
wall to center of the drain, vandal resistant, 6 liters per minute [1.5 gallon] per minute;
“Model No. K-714412-3 by Kohler.
4. Supply Kit: Chrome plated heavy pattern brass stops with full turn brass stem, chlorine
and chloramines resistant replaceable washers, certified to 14 bars [200 psi] line
pressure, “Premier Line” by McGuire with following features:

a. Chrome plated copper risers.

b. Escutcheon flange.
c. Inlet: 13 millimeters [½ inch].
d. Outlet: 13 millimeters [½ inch].
e. Handle: Key, Wheel.
f. 13 millimeters [½-inch] Chrome plated brass supply tube from female 13
millimeters [½-inch] IPS female water supply rough in to stop valve inlet.

5. Drain: Chrome plated drain assembly with cast brass, open grid strainer, 17-gauge, 32
millimeters [1¼-inch] O.D. tailpiece; “155-A” by McGuire.

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-5
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

6. Drain: Chrome plated drain assembly with cast brass, open grid strainer, offset type, 17-
gauge, 32 millimeters [1¼-inch] O.D. tailpiece; “No. 155-WC” by McGuire.
7. Trap:

a. Standard: 32 millimeters x 38 millimeters [1¼-inch x 1½-inch] “P” Trap chrome

plated cast brass “P” Trap body, with 17-gauge seamless tubular wall bend, cast
brass slip nuts or flange; “Premier Line 8902C” by McGuire.
b. Heavy Duty Vandal Resistant: 32 millimeters x 38 millimeters [1¼-inch x 1½-inch]
chrome plated cast body J-Bend trap with 17-gauge wall bend, vandal resistant
construction guaranteed to withstand 407 N-m [300 ft/lb] horizontal or vertical blow,
and chrome plated cast brass set screw wall flange; “No. V8902CNC” by McGuire.

8. Insulation: White, seamless and antimicrobial closed cell vinyl insulation systems,
conforming to ADA article 4.19.4, BOCA 1203.4, covering hot and cold angle stops and
water supplies, lavatory drain and P-trap assembly; secured without exposed plastic ties;
“No. 102” by Truebro, “ProWrap” by McGuire.
9. Support: 25 millimeters x 76 millimeters [1-inch x 3-inch] rectangular steel tubing uprights
welded to 102 millimeters [4-inch] square steel floor anchor plates with concealed arms,
alignment bar, lock nuts, leveling screws, and fixture locking device sized to meet
plumbing fixture rough-in dimensions and provided with extension adaptor of length to
allow floor anchor plates to be installed within plumbing chase behind masonry walls;
“No. 700-M31” by J.R. Smith.

D. Lavatory L-3 Mounting Under Counter:

1. Basin: Vitreous china, white, mounted under counter, 533 millimeters long x 355
millimeters wide [21 inches long x 14 inches wide] rectangular, 102 millimeters [4-inch]
center hole punch, concealed front overflow, self-draining deck area with contoured back
and side splash shields, for concealed arm support; “Model No. K-2215” by Kohler.
2. Faucet: Metal construction, brass valve bodies, reversible quarter-turn washerless
ceramic disc valves, flexible connections for easy installation , pop-up drain with lift rod
and tailpiece, 1310 millimeter (5 – ½ inch), stationary spout, 203 millimeter (8 inch) center
set, vandal resistant, 5.7 liter per minute (1.5 gallon per minute), high cross handles,
“Model No. K14408-3” by Kohler.
3. Supply Kit: Chrome plated heavy pattern brass stops with full turn brass stem, chlorine
and chloramines resistant replaceable washers, certified to 14 bars [200 psi] line
pressure, “Premier Line” by McGuire with following features:

a. Chrome plated copper risers.

b. Escutcheon flange.
c. Inlet: 13 millimeters [½ inch].
d. Outlet: 13 millimeters [½ inch].
e. Handle: Key, Wheel.
f. 13 millimeters [½-inch] Chrome plated brass supply tube from female 13
millimeters [½-inch] IPS female water supply rough in to stop valve inlet.

4. Drain: Chrome plated drain assembly with cast brass, open grid strainer, 17-gauge, 32
millimeters [1¼-inch] O.D. tailpiece; “155-A” by McGuire.
5. Drain: Chrome plated drain assembly with cast brass, open grid strainer, offset type, 17-
gauge, 32 millimeters [1¼-inch] O.D. tailpiece; “No. 155-WC” by McGuire.

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-6
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

6. Trap:

a. Standard: 32 millimeters x 38 millimeters [1¼-inch x 1½-inch] “P” Trap chrome

plated cast brass “P” Trap body, with 17-gauge seamless tubular wall bend, cast
brass slip nuts or flange; “Premier Line 8902C” by McGuire.
b. Heavy Duty Vandal Resistant: 32 millimeters x 38 millimeters [1¼-inch x 1½-inch]
chrome plated cast body J-Bend trap with 17-gauge wall bend, vandal resistant
construction guaranteed to withstand 407 N-m [300 ft/lb] horizontal or vertical blow,
and chrome plated cast brass set screw wall flange; “No. V8902CNC” by McGuire.

7. Insulation: White, seamless and antimicrobial closed cell vinyl insulation systems,
conforming to ADA article 4.19.4, BOCA 1203.4, covering hot and cold angle stops and
water supplies, lavatory drain and P-trap assembly; secured without exposed plastic ties;
“No. 102” by Truebro, “ProWrap” by McGuire.
8. Support: 25 millimeters x 76 millimeters [1-inch x 3-inch] rectangular steel tubing uprights
welded to 102 millimeters [4-inch] square steel floor anchor plates with concealed arms,
alignment bar, lock nuts, leveling screws, and fixture locking device sized to meet
plumbing fixture rough-in dimensions and provided with extension adaptor of length to
allow floor anchor plates to be installed within plumbing chase behind masonry walls;
“No. 700-M31” by J.R. Smith.

E. Lavatory L-4 Boot Sink:

1. Basin: Floor mounted, # millimeters long x # millimeters wide [# inches long x # inches
wide] rectangular, 102 millimeters [4-inch] center hole punch, concealed front overflow,
self-draining deck area with side splash shields.
2. Faucet: Wall mounted trim 22.9 cm (9 inch) 90°spout from wall to center of drain, brass
construction, dual control wall mounted, cross or lever handles, stationary spout, less
drain, 5.7 liters per minute [1.5 gallon per minute]. By Kohler model #K-T11414-3.
3. Trap guard: Trap guard shall be installed the drain for sewer gas and sewage backup
protection. By Proset Systems:

a. Material: Smooth, soft, flexible, elastomeric PVC material molded into shape of
duck’s bill, open on top with curl closure at bottom.
b. Allows wastewater to open and adequately discharge floor drain through its
interior.
c. Closes and returns to original molded shape after wastewater discharge is
complete.

4. Drain: Chrome plated drain assembly with cast brass, open grid strainer, 17-gauge.
5. Insulation: White, seamless and antimicrobial closed cell vinyl insulation systems,
conforming to ADA article 4.19.4, BOCA 1203.4, covering hot and cold angle stops and
water supplies, lavatory drain and P-trap assembly; secured without exposed plastic ties.

2.5 SINK

A. General Characteristics: Faucet Brass Quality Lead-free brass materials and construction, U.L.
listed certifying conformance with NSF Standard 61, Section 9 test protocol for
Residential/Drinking Water Faucets.

B. Sink: SK-1:

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-7
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

1. Bowl: 18 gauge, type 302, stainless steel, single compartment, self-rimming, with 560-
millimeter [22-inch] long x 496-millimeter [19½-inch] wide x 191-millimeter [7½-inch] D
undercoated bowl, mounting clips screws and undermount clamps for casework counter
top thickness of 32 millimeters [1¼ inches] to 38-millimeter [1½-inch], and 3-hole punch;
“No. LR-2219” by Elkay
2. Faucet: Single handle top mount mixing faucet with swing spout, aerator and 8.3 lpm
[2.2 gpm] maximum flow restrictor at 4.1 bar [60 psi]; “No. LK-4100” by Elkay.
3. Supplies: Chrome plated angle supply with 12.7-millimeter x 25-millimeter [½-inch x 12-
inch] flexible riser and 12.7-millimeter x 12.7-millimeter [½-inch x ½-inch] wheel handle
stop and chrome plated cast brass set screw escutcheon; “No. 2167-F” by McGuire.
4. Strainers: Basket strainer with 40-millimeter x 100-millimeter [1½-inch x 4-inch] tailpiece;
“No. 151” by McGuire.
5. Trap: 40-millimeter x 40-millimeter [1½-inch x 1½-inch] chrome plated cast trap with 17-
gauge tubing waste to wall, cleanout plug and chrome plated cast brass set screw
escutcheon; “No. 8912” by McGuire.

C. Sink: SK-2: ADA Compliant Installation:

1. Bowl: 18-gauge, Type 302, stainless steel, two compartment, self-rimming, 840-
millimeter [33-inch] long x 496-millimeter [19½-inch] wide x 191-millimeter [7½-inch]
diameter undercoated bowl, mounting clips screws and undermount clamps for casework
counter top thickness of 32-millimeter to 38-millimeter [1¼-inch to 1½-inch], and 3-hole
punch “No. LR-3319” by Elkay.
2. Faucet: Single handle top mount mixing faucet with swing spout, aerator and 8.3 lpm
[2.2 gpm] maximum flow restrictor at 4.2 bar [60 psi] “No. LK-4100” by Elkay.
3. Strainer: Basket strainer or offset type drain as required for installation; “No. LK-25” by
Elkay.
4. Garbage Disposer: Continuous feed type, high polish sink flange, stainless steel grind
chamber, grind wheel and shredder ring. 0.47 KW [5/8 HP], 220 volts, 50Hz “KCDC250X”
by Kitchen Aid or “No. 50” by Insinkerator.
5. Trap: 40-millimeter x 40-millimeter [1½-inch x 1½-inch] chrome plated cast trap with 17-
gauge tubing waste to wall, cleanout plug and chrome plated cast brass set screw
escutcheon; “No. 8912-F” by McGuire.
6. Dishwasher Tailpiece and Supply Stop:

a. Tailpiece: Sanitary Dash R7591 or R7592, 17-gauge slip joint inlet dishwasher
branch.
b. Supply: Provide 12.7-millimeter [½-inch] separate rough in for dishwasher chrome
plated brass supply wheel handle stop. Verify size of outlet connection required
for connection to dishwasher.

2.6 ELECTRIC WATER COOLER

A. Lead-Free Requirements: Provide all waterway components constructed of lead-free materials

and conforming to definition of “lead-free” as defined in Safe Drinking Water Act of 1986 and
Lead Contamination Control Act of 1988.

B. Electric Water Cooler: EWC-1 – ADA Compliant Installation:

1. Barrier-free water cooler model with mounting assembly, bubbler, push-actuating

mechanism, recessed refrigeration unit, providing 30 liters per hour [8 gph] at 10 degrees
C [50 degrees F], electrical 425W, 220V, 50Hz, single phase. Unit shall have satin
stainless steel finish; “HWDFS8” by Haws.

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-8
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

2. ADA compliant design, stainless steel cabinet, wall hung, two level, 350-millimeter [14-
inch] diameter bowls, electric refrigerated water cooler; “Two Level SwirlFlo No.ERP2-8-
C” by Elkay.

a. Stream Projector: Flexible polyester elastomer hooded stream projector with self-
closing push bar controls mounted on front and built-in flow regulator from 1.4 to
6.9 bar [20 to 100 psi].
b. Compressor: 0.15 KW [1/5 HP], capacity 30 liters per hour [8.0 GPH] of 10 degree
C [50 degree F] water with 26.6 degree C [80 degree F] inlet water and 32.2
degree C [90 degree F] ambient air.
c. Trap: 32-millimeter x 32-millimeter [1¼-inch x 1¼-inch], cast brass DWV “P” Trap
with union joint or slip joints.
d. Supply Stop: 12.7 millimeter x 9.5-mililmeter [½-inch x 3/8-inch] IPS chrome
plated brass supply stop with wheel handle.
e. Dielectric coupler: 12.7 millimeter [½ inch].
f. 12.7-millimeter [½ inch] non-metallic strainer downstream of supply stop.
g. Spout Height: Lower spout height 900 millimeters [3 feet-0 inches] above finished
floor.

2.7 MOP RECEPTORS

A. Mop Receptor: MR-1:

1. Basin: 900-millimeter x 600-millimeter [36-inch x 24-inch], one piece “molded-stone” mop

sink with “Model No. MTB-2424” by Stern Williams and aluminum bumper guard “Model
No. A-20” on all exposed sides with 3-inch outlet and the following accessories:

a. Faucet: Combination hose end faucet with brass vacuum breaker, integral stops,
pail hook, top brace and polished chrome plated brass body and handle
construction.
b. Hose and hose bracket
c. Mop hanger bracket

2. Trap guard: Trap guard shall be installed inside the drain for sewer gas and sewage
backup protection. By Proset Systems:

a. Material: Smooth, soft, flexible, elastomeric PVC material molded into shape of
duck’s bill, open on top with curl closure at bottom.
b. Allows wastewater to open and adequately discharge floor drain through its
interior.
c. Closes and returns to original molded shape after wastewater discharge is
complete.

B. Mop Receptor: MR-2:

1. Basin: 607 millimeters x 607 millimeters [24-inch x 24-inch], one piece “molded-stone”
mop receptor; “Model No. MTB-2424” by Stern Williams and aluminum bumper guard
“Model No. A-20” on all exposed sides with 76 millimeters [3-inch] outlet and following
accessories:

a. Faucet: Combination hose end faucet with brass vacuum breaker, 9.5 lpm [2.5
gpm] integral stops, pail hook, top brace and polished chrome plated brass body

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-9
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

and handle construction; “Model No. 28T9” or “Model No. 28C2383-AC” by Delta,
(for faucets with chemical dispensers).
b. Hose and hose bracket: “Model No. T-35” by Stern Williams.
c. Mop hanger bracket: “Model No. T-40” by Stern Williams.

2. Trap guard: Trap guard shall be installed inside the drain for sewer gas and sewage
backup protection. By Proset Systems:

a. Material: Smooth, soft, flexible, elastomeric PVC material molded into shape of
duck’s bill, open on top with curl closure at bottom.
b. Allows wastewater to open and adequately discharge floor drain through its
interior.
c. Closes and returns to original molded shape after wastewater discharge is
complete.

2.8 SHOWERS

A. Shower SH-1 – Pressure balancing valve with institutional style shower head; “Safety Mix No. 4-
500-CX” by Simmons, including

1. Pressure Balance Mixing Valves: Lever handle, bronze valve body, housing cap and
renewable seat, single bronze stem and housing, stainless steel balancing piston,
adjustable limit stop to limit turn of handle. Supply stops; “Safetymix Pressure Balancing
Valve Mixing” by Symmons
2. Mount valve 1219 millimeters [4 feet-0] inches above finished floor.
3. Shower Head: Heavy cast brass construction with triple chrome plated finish, 9.5 liters
per minute [2.5 gpm] water saving flow restrictor, tamper proof adjustable spray pattern,
and design prohibiting lime build up, installed at 1829 millimeters [6 feet-0 inches] above
finished floor measured to outlet of nozzle to finished floor. Provide anchor plate or
installation on ceramic tile walls.
4. Trap guard: Trap guard shall be installed inside the drain for sewer gas and sewage
backup protection. By Proset Systems:

a. Material: Smooth, soft, flexible, elastomeric PVC material molded into shape of
duck’s bill, open on top with curl closure at bottom.
b. Allows wastewater to open and adequately discharge floor drain through its
interior.
c. Closes and returns to original molded shape after wastewater discharge is
complete.

B. Shower SH-2 – ADA Compliant Installation: ADA compliant design, with shower head on side
wall shower opposite seat with shower controls on side wall opposite seat and on entry side of
stall, recessed count shower panel unit, constructed of 14-gauge 304 stainless steel polished to
No. 4 finish, unit without seat; completely factory assembled, pre-piped and ready for installation
and connection to shower piping; “HN200-SX” by Bradley, included.

1. Pressure Balance Mixing Valve: ADA compliant lever handle, bronze valve body,
housing cap and renewable seat, single bronze stem and housing, stainless steel
balancing piston, adjustable limit stop to limit turn of handle, supply stops; “Safetymix
Pressure Balancing Valve” by Symmons.
2. Shower Head: Includes hand-held shower head with swivel connector and bracket, 1499
millimeters [59-inch] stainless steel extra heavy duty flexible hose, chrome plated elbow

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-10
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

outlet with in-line backflow preventer and quick disconnect, and fixed direction severe
service 9.5 liters per minute [2.5 gpm] shower head.
3. Accessories: Lever handle diverter valve, recessed soap dish, grab bar.
4. Trap guard: Trap guard shall be installed inside the drain for sewer gas and sewage
backup protection. By Proset Systems:

a. Material: Smooth, soft, flexible, elastomeric PVC material molded into shape of
duck’s bill, open on top with curl closure at bottom.
b. Allows wastewater to open and adequately discharge floor drain through its
interior.
c. Closes and returns to original molded shape after wastewater discharge is
complete.

2.9 HYDRANTS

A. General Characteristics: Manufactured with “No lead” brazing rings and USDA approved
lubricants.

B. Wall Hydrants HB-2: Warm climate type box type wall hydrant with integral vacuum breaker in
conforming to ANSI A112.21.3, 20 gauge stainless steel box and 16 gauge stainless steel frame
and cover, ¼ turn valve operation, T-handle key operated locking cover with continuous
stainless steel hinge and full 180° cover opening design, 20-millimeter [¾-inch] straight sweat
inlet connection; “No. 5509QT-SAP-SS” by J.R. Smith

C. Hose Bibs HB-1: Cast brass wall faucet designed so that removal of vacuum breaker makes
hose connection impossible, vacuum breaker complying with ASSE Standard 10 with 20-
millimeter [¾-inch] inlet; “No. Y24CP” or N2Y by Woodford.

2.10 SAFETY EQUIPMENT

A. Emergency Shower ES-1 – ADA Compliant Installation: Horizontal mounted emergency shower,
all polished chrome plated steel brass construction including exposed piping, universal sign,
with stay open ball valve with custom length stainless steel or heavy duty aluminum pull rod;
“Model ESBF643PCC” by Water Saver.

1. Custom length pull rod at 122-centimeter [48-inch] maximum above finished floor.
2. Shower head shroud bottom located at 200-centimeter [80-inch] minimum above finished
floor.

B. Eye Wash/Body Wash EW-1: Deck mounted dual purpose eye wash/drench hose unit with two
gentle spray outlet heads at 45° and squeeze valve with locking clip and vacuum breaker; “No.
EW1022-BP” by Water Saver.

C. Emergency Shower and Eye Wash ESEW-1: Floor mounted emergency shower and eye wash,
all polished chrome plated steel brass construction including exposed piping, universal sign,
with stay-open ball valve with custom length stainless steel or heavy duty aluminum pull rod,
cast aluminum floor flange, corrosion resistant fasteners and anchors.; “ Model SS909PCC” by
Water Saver

D. Emergency Shower and Eye Wash ESEW-2 – ADA Compliant Installation:

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-11
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

1. Horizontal mounted emergency shower, eye wash and face wash, all polished chrome
plated steel brass construction including exposed piping, universal sign, with self-closing
ball valve stainless steel or heavy duty aluminum pull rod; “ Model ESBF643CC-AP600-
354H” by Water Saver

a. Custom length pull rod at 120-centimeter [48-inch] maximum above finished floor.
b. Shower head shroud bottom located at 200-centimeter [80-inch] minimum above
finished floor.
c. Spray heads at 900-millimeter [36-inch] maximum above finished floor.
d. 500-millimeter [19-inch] minimum from centerline of vertical pipe support and
centerline of spray head bowl.
e. 700-millimeter [27-inch] minimum knee clearance from bottom of spray bowl drain
pipe to finished floor.

E. Emergency Eyewash Mixing Valve:

1. Mixing Valve: Chrome plated mixing valve shall control outlet temperature over a wide
range of flow and shall be suitable for single or multiple eyewash applications. The valve
shall include a thermometer to measure the temperature of the stream. Temperature
adjustment shall be vandal resistant. The control mechanism shall employ a liquid filled
thermostatic motor to drive the valve without additional power requirements. The control
mechanism shall employ a stainless steel sliding piston control device with reverse seat
closure and both fixed and variable cold water bypass. In the event of interruption of the
cold water supply, the control mechanism closes off the hot water port, stopping all flow.
In the event of interruption of the hot water supply, the control mechanism shall allow cold
flow through both the fixed and variable bypass.
2. Recessed Cabinet: 580 millimeters [23 inches] tall x 482 millimeters [19 inches] wide x
170 millimeters [6¾ inches] deep, stainless steel construction.

2.11 MISCELLANEOUS

A. Washer Wall Box: Supply and drain unit for automatic washers constructed from hot dipped
galvanized steel 20-gauge box and 18-gauge faceplate.

B. Sanitary Sealant: Acetoxy silicone sealant, white, complying with FS TT-001543A, Type 2 (non-
sag), Class A, listed by NSF to be in compliance with No. F-51 “Plastic Materials and
Components for Use in Food Equipment”, in compliance with FDA Reg. 21 CFR 175.300
“Resinous and Polymeric Coatings” “SCS 1702F® Sealant” by G.E. Silicones.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Provide plumbing fixtures and trim as shown on the Drawings and as specified. Vitreous china
fixtures shall be white, except as otherwise noted.

B. Provide each fixture with all required trim, including but not limited to, carriers, supports,
faucets, stops, waste fitting, traps, seats, flushometer, vacuum breaker, bolts, gaskets, and
escutcheons.

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-12
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

C. Provide chromium plated brass materials for exposed supplies, stops, valves, faucets, strainers,
wastes, bolts, screws, bushings, traps and nipples, exposed piping and wall flanges plates and
escutcheons.

D. Fixture traps shall be “P” Traps.

E. During course of construction cover exposed trim and fittings, fixtures with suitable protection.
When directed, thoroughly clean fixtures and fittings.

F. Be fully responsible for protection of fixtures before and after inspection until final acceptance of
the entire building by the Owner. The contractor regardless of who caused the damage shall
immediately replace any damaged fixture.

G. Provide fixtures free from imperfections, true as to line, angles, curves and color, smooth,
watertight, and practically noiseless in operation.

H. Alternate products shall have clearances, waterways and assembly equal to that of the plate
number of the product selected.

I. Lavatory supports shall be furnished with lavatories for under counter installation. Securely
fasten and support all fixtures. Provide blocking in walls as required to support fixtures.
Conceal all supports. Use expansion shields or toggle bolts for fastening to masonry. Carefully
drill holes to avoid chipping, cracking, etc. Paint exposed ironwork with enamel.

J. Provide chromium plated, cast brass escutcheons with set screws at supply and drain
penetrations through walls and casework.

K. Provide chromium plated brass materials for exposed supplies, stops, valves, faucets, strainers,
wastes, bolts, screws, bushings, traps and nipples, etc.

L. Securely fasten and support supply and drain piping in pipe chases and walls to obtain rigid
installation.

M. Securely fasten and support all fixtures. Provide blocking in walls as required to support
fixtures. Conceal all supports. Use expansion shields or toggle bolts for fastening to masonry.
Carefully drill holes to avoid chipping, cracking, etc. Paint exposed ironwork with enamel.

N. Furnish electrical power requirements for fixtures requiring power, including but no limited to
connection type and rough-in location to electrical work install.

O. Provide sanitary sealant for fixture installations:

1. Apply sealant to a clean and dry surface at temperatures between -6.7 and 32.2 degrees
C [20 and 90 degrees F]. Use rubbing alcohol to clean surface before applying sealant.
Cut opening on spout at desired angle to dispense sealant. Apply sealant with any
standard caulking gun. Smooth off excess as recommended by manufacturer.
2. Caulk between walls hung vitreous china fixtures and wall with sanitary sealant.
3. Caulk between self-rimming counter mounted vitreous china fixtures and counter top of
casework with sanitary sealant.
4. Caulk between floor set vitreous china fixtures and floor with sanitary sealant.
5. Caulk between wall mounted shower valve escutcheon plate and ceramic tile with
sanitary sealant.
6. Caulk between shower head wall plate and ceramic tile with sanitary sealant.
7. Caulk between wall hydrant and wall opening with sanitary sealant.

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-13
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

P. ADA Compliant Installations:

1. Install ADA compliant plumbing fixtures in conformance with Title III of American
Disabilities Act Guidelines and ANSI Standard A112.19.2.
2. Install ADA compliant wall type water closets at 457 millimeters [18 inches] from finished
floor to top of seat.
3. Install ADA compliant water closets with centerline of water closet at no less than 457
millimeters [18 inches] from adjacent wall with grab bar.
4. Install ADA compliant flush valve controls for water closets pointing to wide side of toilet
area at no more than 112 centimeters [44 inches] above finished floor.
5. Install ADA compliant urinal at 432 millimeters [17 inches] from finished floor to rim of lip.
6. Install ADA compliant lavatories with bottom of fixture apron at no less than 737
millimeters [29 inches] above finished floor and minimum knee space of 690 millimeters
[27 inches] from finished floor for distance of 203 millimeters [8 inches] from front of
apron and with distance of finished floor to fixture basin rim set at 864 millimeters [34
inches]. Offset drain rough in, right or left of standard drain rough-in location, to allow
offset drain to be installed and “P” Trap centerline to be parallel with face of wall.
7. Install ADA compliant sinks in ADA compliant casework supplied by Casework Installer.
Locate sink casework cutout in countertop to allow drain, tailpiece, supplies and trap to
be installed within casework. Coordinate sink cutout location, accessories, rough-in and
connection dimensions with Casework Installer and casework shop drawings. Do not
route piping through 230-millimeter [9-inch] high toe space clearance at base of cabinet.
8. Install ADA compliant lavatory in ADA compliant casework supplied by Casework
Installer. Locate lavatory and accessories in countertop to allow drain, tailpiece, supplies
and trap to allow for minimum knee space of 690 millimeters [27 inches] from finished
floor for distance of 200 millimeters [8 inches] from front edge of counter. Coordinate
accessories, lavatory cutout location, and rough-in and connection dimensions with
casework shop drawings to meet the ADA installation criteria. Do not route piping though
9 inches high toe space clearance at base of cabinet.
9. Install ADA compliant washfountains with bottom of fixture apron at no less than 737
millimeters [29 inches] above finished floor and minimum knee space of 690 millimeters
[27 inches] from finished floor for distance of 200 millimeters [8 inches] from front of
apron.
10. Install ADA compliant electric water coolers with spout orifice 0.91 meters [3 feet-0
inches] above the finished floor.
11. Install ADA compliant drinking fountains with spout orifice 0.91 meters [3 feet-0 inches]
above the finished floor.

Q. Standard Fixture Installations (Fixtures not identified to be installed in compliance with ADA
guidelines shall be installed in accordance with the following, unless otherwise indicated on
architectural documents):

1. Lavatories: Install lavatories with top of lavatory bowl 800 millimeters [31 inches] above
finished floor.
2. Wall hung water closets: Install wall hung water closets with rim at 380 millimeters [15
inches] above finished floor.
3. Wall hung urinals: Install wall hung urinals with rim at 600 millimeters [24 inches] above
finished floor.
4. Electric water coolers with spout 100 centimeters [40 inches] above the finished floor.

R. Washer Wall Box: Provide deep seal “P” Trap and standpipe to washer wall box connection.

S. Electric Water Coolers: Flush strainer clean of sediment and adjust water flow regulator valve
on unit to deliver stream to approximately 150 millimeters [6½ inches] from the bubbler.

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-14
23 April 2010 Revised 21 September 2010
 BASRAH SPORTS CITY

T. Mop Receptor:

1. Install mop hanger bracket centered along length of mop receptor on wall adjacent to
faucet with fasteners at 1.2 meters [4 feet-0 inches] above finished floor.
2. Install faucet water supply rough-ins at 0.91 meters [3 feet-0 inches] above finished floor
and centered above mop receptor.
3. Install top of mop bracket at 450 millimeters [18 inches] above finished floor and
centerline of mop bracket 200 millimeters [8 inches] to left or right of the centerline of
faucet.

U. Hydrants:

1. Establish location of wall hydrants rough in and confirm wall-opening sizes with General
Work Prime Contractor.
2. Exterior Hydrant: Install centerline of wall hydrant at 480 millimeters [1 foot-7 inches]
above finished floor, unless otherwise indicated.
3. Interior Wall Hydrants: Install centerline of wall hydrant at 480 millimeters [1 foot-7
inches] above finished floor, unless otherwise indicated.
4. Hose Bibs: Install hose bib with supply inlet centerline at 600 millimeters [2 feet-0 inches]
above finished floor.
5. Multiple Lavatory Faucet Thermostatic Mixing Valve: Locate below lavatory behind
lavatory basin enclosure and on wall.

END OF SECTION

360 Architecture Inc. PLUMBING FIXTURES

MSPRE Preliminary MEP Phase I Construction Documents
091800.00 224000-15
23 April 2010 Revised 21 September 2010