Parts List PL 009-005

January 2015

I/A Series® Electronic Pressure Transmitters

—
IDP10-D, -F, and -T Digital d/p Cell® Transmitters
and
IDP10-A and -V Analog d/p Cell Transmitters
—
Style A

Give instrument Model Code when ordering.

*Parts preceded by an asterisk are recommended spare parts.
See Recommended Spare Parts Summary section for quantities.

TO ORDER PARTS, CALL 1-866-746-6477.

Page 2

NOTE
1. For Transmitter Electronics Housing, refer to Figure 1.

2. For Replacement Sensor Assemblies used with traditional structure, refer to Figure 2.

3. For Replacement Sensor Assemblies used with low profile structures, refer to Figure 3.

4. For Transmitter Bottomworks used with traditional structure, refer to Figure 4.

5. For Transmitter Bottomworks used with low profile structures, refer to Figure 5.

6. For Pressure Seals used with IDP10 Transmitters, refer to Figure 6.

7. For Optional LCD Indicator Assembly, refer to Figure 9.

8. For Optional Custody Transfer Lock and Seal, refer to Figure 10.

9. For Optional Standard Style Mounting Bracket Sets -M1 and -M2, refer to Figure 11.

10. For Optional Universal Style Mounting Bracket Set -M3, refer to Figure 12.

11. For Optional Conduit Connections, refer to Figure 13.

12. For Optional Tubing Connectors, refer to Figure 14.

13. For Optional Adapter Plate Kit used with Coplanar Manifolds, refer to Figure 15.

14. For replacing models 823DP, 843DP, or 863DP with an IDP10 Transmitter, refer to Figure 16.

15. For Optional SIL2 Transmitter for HART Versions, refer to Figure 17.

16. For recommended spare parts summary, refer to the table at end of document.
MODEL CODE Page 3

Model Code
Description Model
I/A Series, Electronic d/p Cell Transmitter for Differential Pressure Measurement IDP10
Electronics Versions and Output Signal
Intelligent; Digital FoxCom, or 4 to 20 mA dc, Configurable (Version -D) -D
Intelligent; Digital Foundation Fieldbus - FISCO Compliant (Version -F) -F
Intelligent; Digital HART and 4 to 20 mA (Version -T) -T
Analog; 4 to 20 mA dc (Version -A) -A
Analog; 1 to 5 V dc, Low Power (Version -V) -V
Structure Code - Select from one of the following six groups:
1. Transmitter with Traditional Structure
Cover Sensor Fill Fluid
Steel Co-Ni-Cr Silicone 10
Steel Co-Ni-Cr Inert 11
Steel 316L ss Silicone 12
Steel 316L ss Inert 13
Steel Nickel Alloy (a) Silicone 16
Steel Nickel Alloy (a.) Inert 17

316 ss Co-Ni-Cr Silicone 20

316 ss Co-Ni-Cr Inert 21
316 ss 316L ss Silicone 22
316 ss 316L ss Inert 23
316 ss 316L ss, Gold Plated Silicone 2G
316ss Monel Silicone 24
316 ss Monel Inert 25
316 ss Nickel Alloy (a.) Silicone 26
316 ss Nickel Alloy (a.) Inert 27

Monel Monel Silicone 34

Monel Monel Inert 35

Nickel Alloy(a.) Nickel Alloy (a.) Silicone 46

Nickel Alloy(a.) Nickel Alloy (a.) Inert 47
Nickel Alloy(a.) Tantalum Silicone 48
Nickel Alloy(a.) Tantalum Inert 49

PVDF Insert (Kynar) Tantalum Silicone (used with Process Connector Type7) 78 (b)
PVDF Insert (Kynar) Tantalum Inert (used with Process Connector Type7) 79 (b)

2. Transmitter with Low Profile Structure LP1 (not available with Pressure Seals)
Cover Sensor Fill Fluid
316 ss 316L ss Silicone LL
316 ss 316L ss Inert LM
316 ss Nickel Alloy(a.) Silicone LC
316 ss Nickel Alloy(a.) Inert LD

3. Transmitter with Low Profile Structure LP2 (not available with Pressure Seals)
Cover Sensor Fill Fluid
316 ss 316L ss Silicone 52
53
316 ss 316L ss Inert 56
316 ss Nickel Alloy(a.) Silicone 57
316 ss Nickel Alloy(a.) Inert

4. Transmitter prepared for Foxboro Model Coded Remote Mount Seals (c) (d)
Transmitter prepared for Remote Seals on Both HI and LO Sides, Silicone Fill in Sensor S1
S2
Transmitter prepared for Remote Seals on Both HI and LO Sides, Inert Fill in Sensor S3
Transmitter prepared for Remote Seal HI Side, 1/2 NPT Connector LO Side, Silicone Fill in Sensor S4
Transmitter prepared for Remote Seal HI Side, 1/2 NPT Connector LO Side, Inert Fill in Sensor S5
Transmitter prepared for Remote Seal LO Side, 1/2 NPT Connector HI Side, Silicone Fill in Sensor S6
Transmitter prepared for Remote Seal LO Side, 1/2 NPT Connector HI Side, Inert Fill in Sensor
Page 4 MODEL CODE

Model Code (Continued)

Description Model
5. Transmitter Prepared for Foxboro Model Coded Direct Connect Seals (c)
PSFLT, PSSCT, or PSSST Direct Connect Seal on HI Side; 1/2 NPT Process Connector LO Side; Silicone Fill F1
PSFLT, PSSCT, or PSSST Direct Connect Seal on HI Side; 1/2 NPT Process Connector LO Side; Inert Fill F2
PSFLT, PSSCT, or PSSST Direct Connect Seal on HI Side; Remote Seal with Capillary LO Side; Silicone Fill F3
PSFLT, PSSCT, or PSSST Direct Connect Seal on HI Side; Remote Seal with Capillary LO Side; Inert Fill F4

6. Transmitter Prepared for non-Foxboro Seals

Remote Seals on High and Low Sides; Silicone Fill in Sensor SA
Remote Seals on High and Low Sides; Inert Fill in Sensor SB
Remote Seal on High Side and 1/2 NPT Connector on Low Side, Silicone Fill in Sensor SC
Remote Seal on High Side and 1/2 NPT Connector on Low Side, Inert Fill in Sensor SD
Remote Seal on Low Side and 1/2 NPT Connector on High Side, Silicone Fill in Sensor SE
Remote Seal on Low Side and 1/2 NPT Connector on High Side, Inert Fill in Sensor SF

Span Limits (Differential Pressure Units)

kPa inH2O mbar
0.12 and 7.5 0.5 and 30 1.2 and 75 A (e)
0.87 and 50 3.5 and 200 8.7 and 500 B
7 and 210 28 and 840 70 and 2100 C
MPa psi bar or kg/cm2
0.07 and 2.1 10 and 300 0.7 and 21 D
0.7 and 21 100 and 3000 7 and 210 E (f)

Process Connector Type (Material Same as Process Cover Material) (g)

See below: 0
For d/p: No connectors; both covers tapped for 1/4 NPT (316 ss only, no side vents)
Flange Mount Hi Side: 1/2 NPT, 316 ss Process Connector on Lo Side (F1 and F2 only)
Flange Mount Hi Side: No connectors; both sides prepared for seals (F3 and F4 only)
Two Remote Seals: No connectors; both covers tapped for capillary connection (S1, S2, SA, SB only)
One Remote Seal: 1/2 NPT, 316 ss Process Connector on Side Opposite Seal (S3 to S6, SC to SF only)

1/4 NPT, Not with Structure Codes 46 to 49, 78, 79, or pressure seals 1
1/2 NPT, Not with Structure Codes 78 or 79, or pressure seals 2
Rc 1/4, Not with Structure Codes 46 to 49, 78, 79, or pressure seals 3
Rc 1/2, Not with Structure Codes 78 or 79, or pressure seals 4
1/2 Schedule 80 Welding Neck, Not with Structure Codes 46 to 49, 78, 79, or pressure seals 6
None; PVDF Insert tapped for 1/2 NPT/Process Inlet on Side of 316 ss Process Covers (only with 78/79 above) 7

Conduit Connection and Housing Material

1/2 NPT Conduit Connection, Aluminum Housing 1
PG 13.5 Conduit Connection, Aluminum Housing (With Electrical Safety Codes E, D, M, and N only) 2
1/2 NPT Conduit Connection, 316 ss Housing 3
PG 13.5 Conduit Connection, 316 ss Housing (With Electrical Safety Codes E, D, M, and N only) 4
M20 Conduit Connection, Both Sides, Aluminum Housing (With Electrical Safety Codes E, D, M, and N only) 5
M20 Conduit Connection, Both Sides, 316 ss Housing (With Electrical Safety Codes E, D, M, and N only) 6

Electrical Safety
ATEX II 1 GD, EEx ia IIC, Zone 0; or II 1/2 GD, EEx ib IIC, Zone 0/1 (with Electronic Versions D and T only) E
ATEX FISCO II 1 GD, EEx ia IIC, Zone 0 (with Electronic Version -F only) E
ATEX II 2 GD, EEx d IIC, Zone 1 (d) D
ATEX II 3 GD, EEx nL IIC, Zone 2 (with Electronic Versions D and T only) N
ATEX FNICO II 3 G, Ex nL IIC, Zone 2 (with Electronic Version F only) N
ATEX Multiple Certifications (includes ATEX Codes E, D, and N) (h) M
MODEL CODE Page 5

Model Code (Continued)

Description Model
CSA Certifications (see table below): C
Electronic Version
Description A D F T V
Intrinsically Safe, Division 1 X X X
Explosionproof, Division 1 X X X X X
Suitable for Class I, II, III; Division 2 X X X X X
Zone certified Ex ia IIC and Ex nA II X X X
FISCO Intrinsically Safe, Division 1 X
FNICO for Class I, II, III; Division 2 X

CSA Certifications: B
Zone certified flameproof, Ex d IIC (with all Electronic Versions)
(also includes all certifications of Code C above)
FM Certifications (see table below): F
Electronic Version
Description A D F T V
Intrinsically Safe, Division 1 X X X
Explosionproof, Division 1 X X X X X
Nonincendive, Class I, II, III; Division 2 X X X X X
Zone approved AEx ia IIC X X X
FISCO Intrinsically Safe, Division 1 X
FNICO nonincendive, Class I, II, III; Division 2 X

FM Approvals: G
Zone approved flameproof, AEx d IIC (with all Electronic Versions)
(also includes all approvals of Code F above)
IECEx Certifications: T
Intrinsically safe, Ex ia IIC (with Electronic Version T only)
FISCO Intrinsically safe, Ex ia IIC (with Electronic Version F only)
IECEx Certifications: U
Protection n, Ex nL IIC (with Electronic Version T only)
FNICO Protection n, Ex nL IIC (with Electronic Version F only)
IECEx Certifications: V
Flameproof, Ex d IIC (with all Electronic Versions)
Multi-marked for ATEX, CSA, and FM Intrinsically Safe Applications (with Electronic Version -T/HART only) W

Optional Selections

Mounting Bracket Set (i)

Standard Style Painted Steel Bracket with Plated Steel Bolts -M1
Standard Style Stainless Steel Bracket with Stainless Steel Bolts -M2
Universal Style Stainless Steel Bracket w/Stainless Steel Bolts (not with Structure Codes LL, LM, LC, or LD) -M3

Digital Indicator with Pushbuttons; or Blind (Solid) Cover over Standard LCD Indicator
Digital Indicator, Pushbuttons, and Window Cover (with Electronic Versions D, F, and T only) -L1
Blind (Solid) Cover replaces Window Cover (with Electronic Versions A and V only) -L2
Page 6 MODEL CODE

Model Code (Continued)

Description Model
DIN 19213 Construction used with Process Connector Code 0 and 316 ss Covers with no side vents
(not available when remote or direct connect seals are specified)
Single Ended Process Cover with M10, B7 Steel Bolting, derated to 16 MPa (2320 psi) (j) -D1
Double Ended Process Cover with M10, B7 Steel Bolting (Blind Kidney Flange on Back) (k) (l) (m) -D2
Single Ended Process Cover with 7/16 in, B7 Steel Bolting; standard pressure rating 25 MPa (3625 psi) (j) -D3
Double Ended Process Cover with 7/16 in, B7 Steel Bolting (Blind Kidney Flange on Back) (k) (l) (m) -D4
Single Ended Process Cover with 7/16 in, 316 ss Bolting; derated to 15 MPa (2175 psi) (j) -D5
Double Ended Process Cover with 7/16 in, 316 ss Bolting (Blind Kidney Flange on Back) (k) (l) (m) -D6
Single Ended Process Cover with 7/16 in, 17-4 ss Bolting; standard pressure rating 25 MPa (3625 psi) (j)) -D7
Double Ended Process Cover with 7/16 in, 17-4 ss Bolting (Blind Kidney Flange on Back) (k) (l) (m) -D8
Single Ended Process Cover with 7/16 in, 17-4 ss Bolting; pressure rating 40 MPa (5800 psi) (j) -D9
(Not available with Span Codes A, D, or E; or Option Codes -V, -B1, -B2, -B3, or -Y)

Cleaning and Preparation - Not Available with Gold-Plated Sensor, Structure 2G, or Pressure Seals
Unit Degreased - for Silicone Filled Sensors Only -X1
(Not for Oxygen/Chlorine/Other Fluids that may react with Silicone)
Cleaned and Prepared for Oxygen Service - for Inert Filled Sensors Only -X2
(Not available with Carbon Steel Covers or with Silicone Filled Sensors)
Cleaned and Prepared for Chlorine Service - for Inert Filled Sensors Only (n) -X3
(Not available with Carbon Steel Covers or with Silicone Filled Sensors)
Bolting for Process Covers/Connectors - Not with DIN 19213 Construction or Structure Codes 78 and
79 (o)
316 ss Bolts and Nuts (Pressure derated to 16 MPa (2320 psi); not available with -Y Option) -B1
17-4 ss Bolts and Nuts (n) -B2
B7-M Bolts and Nuts (NACE)(Pressure derated to 20 MPa (2900 psi)) -B3

Conduit Thread Adapters (Not available with Conduit Connection Codes 5 and 6)
Hawke-Type 1/2 NPT Cable Gland for use with Conduit Connection Codes 1 and 3 (p) -A1
Plastic PG 13.5 Cable Gland for use with Conduit Connection Codes 2 and 4 (q) -A2
M20 Conduit Thread Adapter for use with Conduit Connection Codes 1 and 3 (p) -A3
Brass PG 13.5 Cable Gland (Trumpet-Shaped) for use w/Conduit Connection Codes 2 and 4 (q) -A4

Electronics Housing Features

External Zero Adjustment -Z1
Custody Transfer Lock and Seal -Z2
External Zero Adjustment and Custody Transfer Lock/Seal -Z3

Custom Factory Configuration

Digital Output (4 to 20 mA default if not selected) - only available with Electronic Version -D (FoxCom) -C1
Full Factory Configuration (Requires Configuration Form to be Filled Out) -C2

Tubing Connectors - Not available with Structure Codes 78 and 79; also not available with Seals
Steel, Connecting 6 mm Tubing to 1/4 NPT Process Connector -E1
(Only with Structure Codes 10 to 13; and Process Connector Codes 0 and 1)
Steel, Connecting 12 mm Tubing to 1/2 NPT Process Connector -E2
(Only with Structure Codes 10 to 13; and Process Connector Code 2)
316 ss, Connecting 6 mm Tubing to 1/4 NPT Process Connector -E3
(Only with Structure Codes 10 to 13 and 20 to 23; and Process Connector Codes 0 and 1)
316 ss, Connecting 12 mm Tubing to 1/2 NPT Process Connector -E4
(Only with Structure Codes 10 to 13 and 20 to 23; and Process Connector Code 2)

Vent Screw in Process Cover

Supply Vent Screw in Side of Each Process Cover -V
(Available only on Traditional Process Cover Structure Codes 22 to 47)
Omit Vent Screw in Side of Each Process Cover -V1
(Available only on Type LP1 Low Profile Process Cover Structures Codes LL, LM, LC, and LD)
MODEL CODE Page 7

Model Code (Continued)

Description Model
Adapter Plate, Bolts, and Gaskets for Direct Mount to Competitive Manifolds (r)
See inside pages for manifold compatibility.
Adapter Set for MC Coplanar Manifolds, B7 Bolts (not with options -B1, -B2, or -B3) -P1
Adapter Set for MC Coplanar Manifolds, 316 ss Bolts (requires -B1 option) -P2
Adapter Set for MC Coplanar Manifolds, 17-4 ss Bolts (requires -B2 option) -P3
Adapter Set for MC Coplanar Manifolds, B7M Bolts (requires -B3 option) -P4
Adapter Set for MT3 Coplanar Manifolds, Traditional Flange, B7 Bolts (not with options -B1, -B2, or -B3) -P5
Adapter Set for MT3 Coplanar Manifolds, Traditional Flange, 316 ss Bolts (requires -B1 option) -P6
Adapter Set for MT3 Coplanar Manifolds, Traditional Flange, 17-4 ss Bolts (requires -B2 option) -P7
Adapter Set for MT3 Coplanar Manifolds, Traditional Flange, B7M Bolts (requires -B3 option) -P8

Gaskets
Metal O-ring for pressure seals in Vacuum Service (s) -G1

SIL2 Transmitters for HART Versions Only

SIL2-Certified HART Transmitter -S2

Instruction Books (Common MI, Brochure, and Full Documentation Set on CD-ROM is Standard)
Without Instruction Book and CD; only “Getting Started” brochure is supplied -K1

Miscellaneous Optional Selections

Low Temperature Operative Limit of Electronics Housing extended down to -50°C (-58°F) -J
(Not available with sensors and seals with Inert fill; Structure Codes 78 and 79; and DIN Options -D2, -D4, -
D6, and -D8)
Supplemental Customer Tag (Stainless Steel Tag wired onto Transmitter) -T
Static Pressure Rating to 40 MPa (5800 psi); only with Span Codes B and C -Y
(Not available with:
– Options -B1, -B2, and -B3 (t)
– Options -D1 to -D9
– Structure Codes 34, 35, 78, 79, S1 to S6, SA to SF, F1 to F4)

a. Equivalent to Hastelloy® C. Hastelloy is a registered trademark of Haynes International, Inc.

b. Maximum static pressure rating is 2.1 MPa (300 psi); temperature limits are -7 and +82°C (20 and 180°F).
c. Both Transmitter and Pressure Seal Model Numbers are required. See PSS 2A-1Z11 A for the various pressure seal Model Codes.
d. Remote Seal Models that may be specified are PSFPS, PSFES, PSFAR, PSTAR, PSISR, PSSCR, and PSSSR.
e. Span Limit Code A is not available with pressure seals, except for Sanitary Spud Seals Models PSSSR-.4 and PSSST-.4.
f. Span Limit Code E is not available with Structure Codes 78 and 79 above (PVDF insert in HI side cover).
g. Select Code “0” if a pressure seal is specified. Otherwise select Code 1 through 7.
h. Cover lock provided as standard with Electrical Safety Codes D, B, G, and M.
i. Mounting sets not offered with direct connect (flange mount) seals.
j. Not available with Low Profile Structure Codes 52 to 67.
k. DIN 19213 Options -D2, -D4, -D6, and -D8 derated to 10 MPa (1500 psi).
l. Temperature limits derated to 0 and 60°C (32 and 140°F). Also not available with Structure Codes 52 to 57, and LL, LM, LC, or LD.
m. Mounting Bracket Set options are not available.
n. When -X3 is specified, the standard bolting is replaced with 17-4 ss bolts and nuts. Therefore, there is no need to specify Option -B2 when
selecting the Chlorine Service Option -X3.
o. Not available with DIN construction options. For stainless steel bolts with DIN construction, specify -D5 to -D9, as required.
p. Available with Electric Safety Codes E, D, M, and N only.
q. Available with Electric Safety Code E only.
r. Adapter plate options -P1 to -P8 are not available with:
– Pressure Seal Structure Codes.
– Process Connector Codes 1-7.
– DIN Construction Options -D1, -D2, -D4, -D5, -D6, -D7, -D8, -D9.
s. -G1 is a required option when pressure seal will be used in vacuum applications. This option substitutes vacuum service metal gasket for
standard PTFE process cover gasket.
t. -B2 Bolt Option (17-4 ss) is not available with the -Y option because 17-4 ss bolts and nuts are supplied as part of the -Y option.
 TRANSMITTER ASSEMBLY – ELECTRONICS
Page 8 HOUSING

TRANSMITTER ASSEMBLY – ELECTRONICS HOUSING

Figure 1. Traditional Structure and Low Profile Structures LP1 and LP2

ALWAYS A
ELECTRONICS MODULE
SOLID COVER
CODES -A AND -V 18 (WINDOW
ON THIS END
(INCLUDES LCD 10 COVER)
1 FOR CODE INDICATOR) 3
2 1 2
3 -A or -V
4
16
5 2
6
7 9
8
17
7
6
15
3 (SOLID
COVER)
1 2
LOCK SCREW 13
SEE FIGURE 8

14 13
15
12 ELECTRONICS MODULE
SEE FIGURE 2 10 CODE -D, -F, or -T
20 FOR SENSOR (SEE FIGURE 6 FOR
19 ASSEMBLY OPTIONAL LCD INDICATOR)

TRADITIONAL SEE FIGURE 3

STRUCTURE 12 FOR SENSOR
ASSEMBLY

SEE FIGURE 3
FOR SENSOR
LOW PROFILE ASSEMBLY
STRUCTURE LP1 12
LOW PROFILE
STRUCTURE LP2

NOTE
See Figure 4 for bottomwork parts of traditional structure, and see Figure 5 for bottomwork parts of
low profile structures LP1 and LP2.
TRANSMITTER ASSEMBLY – ELECTRONICS
HOUSING Page 9

Table 1. Part Numbers for Figure 1

Item Part No. Qty. Part Name

1 Below Cover, Aluminum - with Versions -A or -V
D0162AP 1 Solid Cover (Two required with Option -L2)
D0162LG 1 Window Cover (None required with Option -L2)

Below Cover, Stainless Steel - with Versions -A or -V

D0162VD 1 Solid Cover (Two required with Option -L2)
D0162VG 1 Window Cover (None required with Option -L2)

Below Cover, Aluminum - with Versions -D, -F, or -T

D0162AP 2 Solid Cover - See Figure 3 for -L1 LCD Indicator Option with a
Window Cover

Below Cover, Stainless Steel - with Versions -D, -F, or -T

D0162VD 2 Solid Cover - See Figure 3 for -L1 LCD Indicator Option with a
Window Cover

2 X0118CC 1 Grease, Lubriplate (1-3/4 ounce tube)

*3 X0201FC 2 O-Ring, Cover

4 Below 4 Screw, Terminal Block Assy, 0.138-32 x 0.750

X0133UW Steel Screw - used with Aluminum Housing
X0133VP 316 ss Screw - used with 316 ss Housing

5 Below 1 Terminal Block Assembly

D0149YB Electronics Versions -A, -D, and -T
D0149HN Electronics Versions -F
D0149FE Electronics Version -V

6 P0177JE 1 Cable, Power, Replaceable (Versions -F and -V only)

7 D0162VJ 4 Screw Assembly, Earth (Ground), 0.164-32 x 0.375

8 X0144KR 1 O-Ring

9 Below 1 Pipe Plug for Unused Conduit Connection – see WARNING

B0139CA Pipe Plug, Aluminum,1/2 NPT; with Housing Code 1
B0139SK Pipe Plug, 316 ss, 1/2 NPT; with Housing Code 3
X0178GT Pipe Plug, 316 ss, PG 13.5; with Housing Codes 2 and 4
D0179FJ Pipe Plug, Aluminum, M20; with Housing Code 5
D0179FK Pipe Plug, 316 ss, M20; with Housing Code 6

*10 Below 1 Electronics Module

D0162VR Digital FoxCom and/or 4 to 20 mA (Version -D)
D0162UU Digital FOUNDATION Fieldbus - FISCO Compliant (Version -F)
D0162VZ Digital HART and 4 to 20 mA (Version -T)
D0162ZP Analog 4 to 20 mA (Version -A)
D0162ZX Analog 1 to 5 V dc, Low Power (Version -V)
 TRANSMITTER ASSEMBLY – ELECTRONICS
Page 10 HOUSING

Table 1. Part Numbers for Figure 1 (Continued)

Item Part No. Qty. Part Name

11 – – Item 11 is intentionally not used

*12 Below 1 Replacement Sensor Assembly - see Note

Figure 2 For use with Traditional Structure
Figure 3 For use with Low Profile Structures LP1 and LP2

13 D0162WM 2 Screw, Lock, 0.164-32; part of Optional Selection -Z2;

Refer to Figure 10

14 S0102BT 1 Plug, Poly (Remove prior to Transmitter Installation)

15 Below 2 Screw, Captive, Pan Head, 0.138-32 x 0.615

D0162VM Steel Screw - used with Aluminum Housing
D0166CY 316 ss Screw - used with 316 ss Housing

16 D0162WS 1 HHT Plug, Analog (Code -A or -V)

17 X0173YA 1 Washer, Ext. Ground, 0.196 ID, 0.383 OD
18 X0201FW 2 Button
19 D0197PS 1 Clip, Retention
20 X0174EK 1 Screw, Button Head; 0.164-32 x 0.25 long

! WARNING
To maintain IP66 (IEC 529) and NEMA 4X protection, the unused conduit opening must be closed
with a metal plug. In addition, the threaded housing covers must be properly installed.

NOTE
The sensor assembly configuration varies with transmitter structure used, and also fill fluid, wetted
part material, and maximum span. Refer to Figure 2 for replacement sensor assembly part
numbers used with traditional structure, and refer to Figure 3 for replacement sensor assembly part
numbers used with low profile structures.
REPLACEMENT SENSOR ASSEMBLY Page 11

REPLACEMENT SENSOR ASSEMBLY

Figure 2. Replacement Sensor Assembly (Item 12 of Figure 1) For use with Traditional Structure

! WARNING
Failure to install the
1 2 proper Housing Neck
O-Ring (Item 1) for
CSA-labeled
products violates
ANSI/ISA 12.27.01

Table 2. Part Numbers for Figure 2

Item Part No. Qty. Part Name

*1 Below 1 O-Ring, Housing Neck
X0201LY O-Ring, Standard
X0144KW O-Ring for use with CSA Certifications only; see Warning
2 X0118CC A/R Lubricant

Table 3. Traditional Structure Co-Ni-Cr Sensor; Silicone Oil Fill; Steel or 316 ss Cover

Reference
Part Number Model Code Maximum Span
D0175DA IDP10-**0A 7.5 kPa (30 inH2O)
D0175AA IDP10-**0B 50 kPa (200 inH2O)
D0175AD IDP10-**0C 210 kPa (840 inH2O)
D0175AG IDP10-**0D 2.1 MPa (300 psi)
D0175AK IDP10-**0E 21 MPa (3000 psi)

Table 4. Traditional Structure Co-Ni-Cr Sensor; Inert Oil Fill; Steel or 316 ss Cover

Reference Model
Part Number Code Maximum Span
D0175DG IDP10-**1A 7.5 kPa (30 inH2O)
D0175AN IDP10-**1B 50 kPa (200 inH2O)
D0175AR IDP10-**1C 210 kPa (840 inH2O)
D0175AU IDP10-**1D 2.1 MPa (300 psi)
D0175AX IDP10-**1E 21 MPa (3000 psi)
Page 12 REPLACEMENT SENSOR ASSEMBLY

Table 5. Traditional Structure 316L ss Sensor; Silicone Oil Fill; Steel or 316 ss Cover

Reference
Part Number Model Code Maximum Span
D0175DB IDP10-**2A 7.5 kPa (30 inH2O)
D0175AB IDP10-**2B 50 kPa (200 inH2O)
D0175AE IDP10-**2C 210 kPa (840 inH2O)
D0175AH IDP10-**2D 2.1 MPa (300 psi)
D0175AL IDP10-**2E 21 MPa (3000 psi)

Table 6. Traditional Structure 316L ss/Gold Plated Sensor; Silicone Oil Fill; 316 ss Cover

Reference
Part Number Model Code Maximum Span
D0175DF IDP10-*2GA 7.5 kPa (30 inH2O)
D0175BS IDP10-*2GB 50 kPa (200 inH2O)
D0175BT IDP10-*2GC 210 kPa (840 inH2O)
D0175BU IDP10-*2GD 2.1 MPa (300 psi)
D0175BV IDP10-*2GE 21 MPa (3000 psi)

Table 7. Traditional Structure 316L ss Sensor; Inert Oil Fill; Steel or 316 ss Cover

Reference
Part Number Model Code Maximum Span
D0175DH IDP10-**3A 7.5 kPa (30 inH2O)
D0175AP IDP10-**3B 50 kPa (200 inH2O)
D0175AS IDP10-**3C 210 kPa (840 inH2O)
D0175AV IDP10-**3D 2.1 MPa (300 psi)
D0175AY IDP10-**3E 21 MPa (3000 psi)

Table 8. Traditional Structure Monel Sensor; Silicone Oil Fill; 316 ss or Monel Cover

Reference
Part Number Model Code Maximum Span
D0175DC IDP10-**4A 7.5 kPa (30 inH2O)
D0175BA IDP10-**4B 50 kPa (200 inH2O)
D0175BB IDP10-**4C 210 kPa (840 inH2O)
D0175BC IDP10-**4D 2.1 MPa (300 psi)
D0175BD IDP10-**4E 21 MPa (3000 psi)

Table 9. Traditional Structure Monel Sensor; Inert Oil Fill; 316 ss or Monel Cover

Reference
Part Number Model Code Maximum Span
D0175DJ IDP10-**5A 7.5 kPa (30 inH2O)
D0175BE IDP10-**5B 50 kPa (200 inH2O)
D0175BF IDP10-**5C 210 kPa (840 inH2O)
D0175BG IDP10-**5D 2.1 MPa (300 psi)
D0175BH IDP10-**5E 21 MPa (3000 psi)
REPLACEMENT SENSOR ASSEMBLY Page 13

Table 10. Traditional Structure Nickel Alloy (a) Sensor; Silicone Oil Fill; Steel, 316 ss, or Nickel Alloy (a)Cover

Reference
Part Number Model Code Maximum Span
D0175DD IDP10-**6A 7.5 kPa (30 inH2O)
D0175AC IDP10-**6B 50 kPa (200 inH2O)
D0175AF IDP10-**6C 210 kPa (840 inH2O)
D0175AJ IDP10-**6D 2.1 MPa (300 psi)
D0175AM IDP10-**6E 21 MPa (3000 psi)

a. Equivalent to Hastelloy® C. Hastelloy is a registered trademark of

Haynes International, Inc.

Table 11. Traditional Structure Nickel Alloy (a) Sensor; Inert Oil Fill; Steel, 316 ss, or Nickel Alloy (a)Cover

Reference Model
Part Number Code Maximum Span
D0175DK IDP10-**7A 7.5 kPa (30 inH2O)
D0175AQ IDP10-**7B 50 kPa (200 inH2O)
D0175AT IDP10-**7C 210 kPa (840 inH2O)
D0175AW IDP10-**7D 2.1 MPa (300 psi)
D0175AZ IDP10-**7E 21 MPa (3000 psi)

a. Equivalent to Hastelloy® C. Hastelloy is a registered trademark of

Haynes International, Inc.

Table 12. Traditional Structure Tantalum Sensor; Silicone Oil Fill; Nickel Alloy (a) Cover, or PVDF Insert in Cover

Reference
Part Number Model Code Maximum Span
D0175DE IDP10-**8A 7.5 kPa (30 inH2O)
D0175BJ IDP10-**8B 50 kPa (200 inH2O)
D0175BK IDP10-**8C 210 kPa (840 inH2O)
D0175BL IDP10-**8D 2.1 MPa (300 psi)

a. Equivalent to Hastelloy® C. Hastelloy is a registered trademark of

Haynes International, Inc.

Table 13. Traditional Structure Tantalum Sensor; Inert Oil Fill; Nickel Alloy (a) Cover, or PVDF Insert in Cover

Reference
Part Number Model Code Maximum Span
D0175DL IDP10-**9A 7.5 kPa (30 inH2O)
D0175BN IDP10-**9B 50 kPa (200 inH2O)
D0175BP IDP10-**9C 210 kPa (840 inH2O)
D0175BQ IDP10-**9D 2.1 MPa (300 psi)

a. Equivalent to Hastelloy® C. Hastelloy is a registered trademark

of Haynes International, Inc.
Page 14 REPLACEMENT SENSOR ASSEMBLY

Figure 3. Replacement Sensor Assembly (Item 12 of Figure 1) For use with Low Profile Structures LP1 and LP2

! WARNING
Failure to install the proper
1 2 Housing Neck O-Ring
(Item 1) for CSA-labeled
products violates
ANSI/ISA 12.27.01

Table 14. Part Numbers for Figure 3

Item Part No. Qty. Part Name

*1 Below 1 O-Ring, Housing Neck
X0201LY O-Ring, Standard
X0144KW O-Ring for use with CSA Certifications only; see WARNING
2 X0118CC A/R Lubricant

Table 15. Low Profile LP1 and LP2 Structures 316L ss Sensor; Silicone Oil Fill; 316 ss Covers

Reference Model Codes

Part Number LP1 LP2 Maximum Span
D0170WA IDP10-*LLA IDP10-*52A 7.5 kPa (30 inH2O)
D0170WB IDP10-*LLB IDP10-*52B 50 kPa (200 inH2O)
D0170WC IDP10-*LLC IDP10-*52C 210 kPa (840 inH2O)
D0170WD IDP10-*LLD IDP10-*52D 2.1 MPa (300 psi)
D0170WE IDP10-*LLE IDP10-*52E 21 MPa (3000 psi)

Table 16. Low Profile LP1 and LP2 Structures 316L ss Sensor; Inert Oil Fill; 316 ss Covers

Reference Model Codes

Part Number LP1 LP2 Maximum Span
D0170WF IDP10-*LMA IDP10-*53A 7.5 kPa (30 inH2O)
D0170WG IDP10-*LMB IDP10-*53B 50 kPa (200 inH2O)
D0170WH IDP10-*LMC IDP10-*53C 210 kPa (840 inH2O)
D0170WJ IDP10-*LMD IDP10-*53D 2.1 MPa (300 psi)
D0170WK IDP10-*LME IDP10-*53E 21 MPa (3000 psi)
REPLACEMENT SENSOR ASSEMBLY Page 15

Table 17. Low Profile LP1 and LP2 Structures Nickel Alloy (a) Sensor; Silicone Oil Fill; 316 ss Covers

Reference Model Codes

Part Number LP1 LP2 Maximum Span
D0170WL IDP10-*LCA IDP10-*56A 7.5 kPa (30 inH2O)
D0170WM IDP10-*LCB IDP10-*56B 50 kPa (200 inH2O)
D0170WN IDP10-*LCC IDP10-*56C 210 kPa (840 inH2O)
D0170WP IDP10-*LCD IDP10-*56D 2.1 MPa (300 psi)
D0170WQ IDP10-*LCE IDP10-*56E 21 MPa (3000 psi)

a. Equivalent to Hastelloy® C. Hastelloy is a registered trademark of Haynes International, Inc.

Table 18. Low Profile LP1 and LP2 Structures Nickel Alloy (a) Sensor; Inert Oil Fill; 316 ss Covers

Reference Model Codes

Part Number LP1 LP2 Maximum Span
D0170WR IDP10-*LDA IDP10-*57A 7.5 kPa (30 inH2O)
D0170WS IDP10-*LDB IDP10-*57B 50 kPa (200 inH2O)
D0170WT IDP10-*LDC IDP10-*57C 210 kPa (840 inH2O)
D0170WU IDP10-*LDD IDP10-*57D 2.1 MPa (300 psi)
D0170WV IDP10-*LDE IDP10-*57E 21 MPa (3000 psi)

a. Equivalent to Hastelloy® C. Hastelloy is a registered trademark of Haynes International, Inc.

Page 16 TRANSMITTER ASSEMBLY

TRANSMITTER ASSEMBLY

Figure 4. Transmitter Assembly – Bottomworks for use with Traditional Structure

BOTTOMWORKS WITH
PROCESS CONNECTOR
CODES 0 TO 6
1
3
PLUG USED WITH
OPTION -V 10
14

6
1
8 7
9
OPTIONAL VENT 2
SCREW (2 PLACES) 10 1
OPTIONAL 4
SELECTION -V 5 2 3
1 8

BOTTOMWORKS WITH
PROCESS CONNECTOR
CODE 7

2
15
8 10 1
1
15 3
2

BOTTOMWORKS WITH
OPTION -D1, -D3, -D5, -D7
AND -D9

1 8
10 11
11
1
BOTTOMWORKS WITH
OPTION -D2, -D4, -D6, -D8 3
13
12
9

1 8 10 11
11
TRANSMITTER ASSEMBLY Page 17

Table 19. Part Numbers for Figure 4

Item Part No. Qty. Part Name

1 X0118CC 1 Grease, Lubriplate (1-3/4 ounce tube)

2 Below 2 Process Cover for use with Process Connection Codes 0-6 (a)
D0161NA 316 ss
D0161NB Carbon Steel
D0161NC Nickel Alloy (b)
D0161ND Monel

2 Below 2 Side Vent Process Cover for use with Process Connection Codes 0-6 (a)
D0161NE 316 ss
D0161NF Carbon Steel
D0161NG Nickel Alloy (b)
D0161NH Monel

2 D0175TB 2 Cover, 316 ss – for use with Process Connector Code 7 only
(Item 15 PVDF insert fits into cover)

3 Below 2 Screw, Hex Head, 0.500-13 x 3.5

X0173RP 2H (ASTM A193, Gr. B7 [std])
X0173TQ 316 ss (ASTM F593, Group 2) (Options -B1, -D5, -D6)
X0173UK ASTM A193, Gr. B7M (Option -B3)
X0173TD 17-4 ss (ASTM A564, Type 630) (Options -B2, -D7, -D8, -D9)

*4 Below 2 Vent Screw

B0138MJ 316 ss (std)
B0138MK Monel
D0175PQ Nickel Alloy (a) (b)

*5 Below 2 Vent Plug (c)

D0161QT 316 ss (std)
D0161QU Monel
D0175PP Nickel Alloy (a) (b)

6 Table 20 2 Process Connectors (See Table 20 below)

7 Below 4 Screw, Hex Head, 0.438-20 x 1.5 (for threaded connectors, Codes 1-4)
X0100MN ASTM A193 Gr. B7 (std)
X0171VP ASTM A193, Gr. B7M (Option -B3)
X0118AX 17-4 Stainless Steel (Options -B2, -D7, -D8, -D9, -Y)
N1205RQ 316 ss (Options -B1, -D5, -D6)

7 Below 4 Screw, Hex Head, 0.438-20 x 1.0 (for weld neck connectors, Code 6)
X0100NT ASTM A193, Gr. B7 (std)
X0171VN ASTM A193, Gr. B7M (Option -B3)
X0118AY 17-4 Stainless Steel (Options -B2, -Y)
X0173TP 316 ss (Option -B1)
Page 18 TRANSMITTER ASSEMBLY

Table 19. Part Numbers for Figure 4 (Continued)

Item Part No. Qty. Part Name

8 Below 2 Nut, Hex Head, 0.500-13
X0173RN 2H (ASTM A193, Gr. B7 [std])
X0173TR 316 ss (ASTM F594, Group 2) (Options -B1, -D5, -D6)
X0173UJ 17-4 ss (ASTM F594, Group 2) (Options -B2, -D7, -D8, and -D9)
X0173UL ASTM A194, Gr. 2HM (Option -B3)

*9 D0114RB 2 Gasket, PTFE

*10 Below 2 Gasket, Process Cover

D0161QQ Glass-filled PTFE (Standard)
X0145MJ Viton – for use with Process Connector Code 7 only

11 Below 1 Cover, 316 ss - for use with Options -D1, -D3, -D5, -D7, and -D9
D0161NK Single-ended process connection M10 (Option -D1) (High Side)
D0161NJ Single-ended process connection M10 (Option -D1) (Low Side)
D0161NM Single-ended process connection 7/16 (Options -D3, -D5, -D7) (High Side)
D0161NL Single-ended process connection 7/16 (Options -D3, -D5, -D7) (Low Side)
D0174BU Single-ended process connection 7/16 (Option -D9) (High Side)
D0174BT Single-ended process connection 7/16 (Option -D9) (Low Side)

11 Below 2 Cover, 316 ss - for use with Options -D2, -D4, -D6, and -D8
D0161NN Double-ended process connection M10 (Option -D2)
D0161NA Double-ended process connection 7/16 (Options -D4, -D6, -D8)

12 D0153RK 2 Kidney Flange, Blind, 316 ss - for use with Options -D2, -D4, -D6, and -D8
(for double-ended process cover)

13 Below 4 Screw, Hex Head, steel - for use with Options -D2, -D4, -D6, and -D8
X0173MJ M10 x 1.5 x 40 mm, for Option -D2
X0100MN 0.437-20 x 1.5 in, for Options -D4, -D6, and -D8

14 Below 2 Pipe Plug, Hex Head, 1/4 NPT

D0161LU 316 ss
D0161LV Monel
D0161LW Nickel Alloy (b)

*15 D0175TA 2 Insert, PVDF – for use with Process Connector Code 7 only

a. Metallic process wetted material conforming to NACE Standard MR-01-75.

b. Equivalent to Hastelloy® C. Hastelloy is a registered trademark of Haynes International, Inc.
c. For simplified calibration, install F0101ES screw for pressure up to 0.7 MPa (100 psi).

Table 20. Item 6, Process Connectors

Used with Following Cover Material
Process Connector
Conn. Code Description Carbon Steel Stainless Steel Nickel Alloy (a) Monel
1 1/4 NPT N0141XF N0141XT – N0141XK
2 1/2 NPT N0141XM N0141XN B0139JW N0141XL
3 Rc 1/4 B0139BB B0139BD – N0139BC
TRANSMITTER ASSEMBLY Page 19

Table 20. Item 6, Process Connectors

Used with Following Cover Material
Process Connector
Conn. Code Description Carbon Steel Stainless Steel Nickel Alloy (a) Monel
4 Rc 1/2 B0139BE B0139BG B0139JV N0139BF
6 1/2 Schedule 80 Weld Neck N0141XP N0141XR – D0143CZ

a. Equivalent to Hastelloy® C. Hastelloy is a registered trademark of Haynes International, Inc.

Figure 5. Transmitter Assembly – Bottomworks for use with Low Profile Structures LP1 and LP2

BOTTOMWORKS WITH
LOW PROFILE 1
STRUCTURE LP1 2 8
5 4

2
5
1 4
3
9

10
9
6
7

BOTTOMWORKS WITH
LOW PROFILE
STRUCTURE LP2 1
2 5 4 8

2
5
1 4
3

10
9
6
7
7
Page 20 TRANSMITTER ASSEMBLY

Table 21. Part Numbers for Figure 5

Item Part No. Qty. Part Name

1 X0118CC A/R Grease, Lubriplate (1-3/4 ounce tube)

2 Below Below Process Cover with Process Connection Codes 0-6; (a)
D0170WW 1 with LP1; High Side Cover; 316 ss
D0170WY 1 with LP1; Low Side Cover; 316 ss
D0174BZ 2 with LP2, High and Low Side Covers; 316 ss

3 Below 2 Screw, hex head, 0.500-13 x 3.5

X0173RP 2H (ASTM A193, Gr. B7 [std])
X0173UK ASTM A193, Gr. B7M (Option -B3)
X0173TQ 316 ss (ASTM F593, Group 2) (Option -B1)
X0173TD 17-4 ss (ASTM A564, Type 630) (Option -B2)

*4 Below 2/4 Vent Screw; two with LP1 and four with LP2
B0138MJ 316 ss
D0175PQ Nickel Alloy (a) (b)

*5 Below 2/4 Vent Plug, 316 ss; two with LP1 and four with LP2 (c)
D0161QT 316 ss
D0175PP Nickel Alloy (a) (b)

6 Table 22 2 Process Connectors (see Table 22 below)

7 Below 4 Screw, hex head, 0.438-20 x 1.5 (for threaded connectors, Codes 1-4)
X0100MN ASTM A193 Gr. B7 (std)
X0171VP ASTM A193, Gr. B7M, (Option -B3)
N1205RQ 316 ss (Option -B1)
X0118AX 17-4 Stainless Steel (Option -B2)

7 Below 4 Screw, hex head, 0.438-20 x 1.0 (for weld neck connectors, Code 6)
X0100NT ASTM A193, Gr. B7 (std)
X0171VN ASTM A193, Gr. B7M (Option -B3)
X0173TP 316 ss (Option -B1)
X0118AY 17-4 Stainless Steel (Option -B2)

8 Below 2 Nut, 0.500-13

X0173RN 2H, (ASTM A193, Gr. B7 [std])
X0173UL ASTM A194, Gr. 2HM (Option -B3)
X0173TR 316 ss (ASTM F594, Group 2) (Option -B1)
X0173UJ 17-4 ss (ASTM F594, Group 2) (Option -B2)

*9 D0114RB 2 Gasket, PTFE; Sensor Assembly to Process Cover

*10 D0161QQ 2 Gasket, Glass-filled PTFE; Process Connector to Process Cover

a. Metallic process wetted material conforming to NACE Standard MR-01-75.

b. Equivalent to Hastelloy® C. Hastelloy is a registered trademark of Haynes International, Inc.
c. For simplified calibration, install F0101ES screw for up to 0.7 MPa (100 psi).
TRANSMITTER ASSEMBLY Page 21

Table 22. Item 6, Process Connector Part Numbers

Process Process Used with Following Cover Material
Connector Connector
Code Description Stainless Steel Nickel Alloy (a)
1 Tapped for 1/4 NPT N0141XT –
2 Tapped for 1/2 NPT N0141XN –
3 Tapped for R 1/4 B0139BD –
4 Tapped for R 1/2 B0139BG –
6 1/2 Schedule 80 Weld Neck N0141XR –

a. Equivalent to Hastelloy® C. Hastelloy is a registered trademark of Haynes International, Inc.

Page 22 PRESSURE SEALS

PRESSURE SEALS

Figure 6. Pressure Seals for use With IDP10 Transmitters (Part 1)

MODEL PSFLT MODELS PSFPS AND PSFES

DIRECT CONNECT FLUSH DIAPHRAGM-FLANGED CONNECTION
FLANGED LEVEL SEAL REMOTE MOUNT SEAL

TERMINALS
TERMINALS

FIELD
FIELD

FLUSH
DIAPHRAGM
SURFACE
PSFPS HAS
L-H
L-H FLUSH
DIAPHRAGM

PSFES HAS
EXTENDED
EXTENDED FLUSH
FLUSH DIAPHRAGM
DIAPHRAGM
SURFACE

MODEL PSSST MODEL PSSCT

DIRECT CONNECT DIRECT CONNECT
SANITARY TANK SPUD SEAL SANITARY SEAL WITH TRI-CLAMP

TRI-CLAMP CONNECTION.
(SEE NOTE BELOW)
TERMINALS
TERMINALS

FIELD
FIELD

VARIABLE 2- OR 3- INCH
EXTENSION TRI-CLAMP
LENGTH AND GASKET,
AND MATING
L-H
PROCESS
L-H
CONNECTOR
(BY USER)

PROCESS PIPE
NOTE (REFERENCE)
CLAMP AND O-RING ARE SUPPLIED
WITH TRANSMITTER/SEAL ASSEMBLY.

NOTE
The pressure seals shown in Figure 6 are used with the IDP10 Transmitters (traditional
structures only). They (along with the sensor assemblies) are not replaceable items, but must be
replaced with the entire transmitter/seal assembly. In this case, both transmitter and pressure seal
Model Numbers must be used for the assembled transmitter/seal system. Refer to data plates
attached to Transmitter and Pressure Seal for applicable part numbers, or refer to PSS 2A-1Z11A
for Pressure Seal Model Codes.
PRESSURE SEALS Page 23

Figure 7. Pressure Seals for use With IDP10 Transmitters (Part 2)

MODEL PSFAR
RECESSED DIAPHRAGM-FLANGED CONNECTION
REMOTE MOUNT SEAL
WELDED TO CAPILLARY
CONNECTION AT BOTH
INSTRUMENT AND SEAL.
(SOME MODELS MAY HAVE
USER-SUPPLIED CAPILLARY THREADED
FLANGE BOLTS AT SEAL.)
CONNECT TO FOUR STUDS FOR
PROCESS FLANGE 4 BOLTS ATTACH CONNECTION TO
WHEN SEAL HAS UPPER HOUSING PROCESS FLANGE
A 2.4 OR 3.0 INCH TO LOWER HOUSING WHEN SEAL HAS A
DIAPHRAGM 4.0 INCH DIAPHRAGM

MODEL PSTAR
RECESSED DIAPHRAGM-THREADED CONNECTION
REMOTE MOUNT SEAL
SIX BOLTS FOR WELDED TO CAPILLARY
CONNECTION AT BOTH SIX BOLTS FOR
ATTACHING UPPER
INSTRUMENT AND SEAL. ATTACHING UPPER
HOUSING TO LOWER
(SOME MODELS MAY HAVE HOUSING TO LOWER
HOUSING
CAPILLARY THREADED HOUSING
AT SEAL.)
3.0 INCH 4.0 INCH
DIAPHRAGM DIAPHRAGM
1/4 TO 1 1/2 NPT TO
PROCESS CONNECTION

MODEL PSISR
RECESSED DIAPHRAGM - IN-LINE SADDLE WELD
REMOTE MOUNT SEAL
EIGHT BOLTS FOR WELDED TO CAPILLARY EIGHT BOLTS FOR
ATTACHING UPPER CONNECTION AT BOTH ATTACHING UPPER
HOUSING TO LOWER INSTRUMENT AND SEAL. HOUSING TO LOWER
HOUSING (SOME MODELS MAY HAVE HOUSING
CAPILLARY THREADED
AT SEAL.)
4-INCH
IN-LINE SADDLE WELD PROCESS
3-INCH (BUT THE LOWER HOUSING PIPE AND
LESS THAN TO PROCESS PIPE PRIOR LARGER
4-INCH) TO ASSEMBLING UPPER
PROCESS HOUSING TO LOWER
PIPE. HOUSING.
Page 24 PRESSURE SEALS

Figure 8. Pressure Seals for use With IDP10 Transmitters (Part 3)

MODEL PSSCR
FLUSH DIAPHRAGM - SANITARY, TRI-CLAMP
REMOTE MOUNT SEAL

TRANSMITTER
(REFERENCE)

TERMINALS
FIELD
O-RING AND
TRI-CLAMP BY
USER (REFERENCE)

WELDED PROCESS PIPE

CAPILLARY (REFERENCE)
L-H
CONNECTION

MODEL PSSSR
FLUSH DIAPHRAGM - SANITARY, TRI-CLAMP
REMOTE MOUNT SEAL

TRANSMITTER
(REFERENCE)
TERMINALS
FIELD

TRI-CLAMP CONNECTION.
(SEE NOTE BELOW)
WELDED
L-H CAPILLARY VARIABLE
CONNECTION EXTENSION
LENGTH

NOTE
CLAMP AND O-RING ARE SUPPLIED
WITH TRANSMITTER/SEAL ASSEMBLY.
OPTIONAL SELECTIONS Page 25

OPTIONAL SELECTIONS

Figure 9. Optional Liquid Crystal Display (LCD) Indicator Assembly Optional Selection -L1 for Electronics
Version Codes -D, -F, and -T Only

5 3
2 1

NOTE
WINDOW COVER
4 REPLACES SOLID
COVER WHEN
LCD INDICATOR
IS USED.

Table 23. Part Numbers for Figure 9

Item Part No. Qty. Part Name

1 Below 1 Cover Assembly with Window - used with LCD Indicator
D0162LH Aluminum Cover Assembly
D0162VH Stainless Steel Cover Assembly
*2 D0162LQ 1 Indicator Module
3 X0118CC A/R Grease, Lubriplate (1-3/4 ounce tube)
4 P0177HB 1 Indicator Cable
5 0048130 A/R Grease, Silicone (150 gram tube)

Figure 10. Optional Custody Transfer Lock and Seal Optional Selection -Z2

2 3

4
3 2
1

Table 24. Part Numbers for Figure 10

Item Part No. Qty. Part Name

1 S001806 2 Lead Seal
2 D0162WM 2 Screw, Lock, 0.164-32
3 X0118CC A/R Grease, Lubriplate (1-3/4 ounce tube)
4 S001807 A/R Sealing Wire
Page 26 OPTIONAL SELECTIONS

NOTE
Item 2 cover lock screw is provided as standard construction with Electrical Safety Codes D, M, B,
and G.

Figure 11. Optional Standard Style Mounting Bracket Sets, Optional Selection -M1 or -M2 and Optional
Standoff Kits
4
2

1
3

TRADITIONAL LOW PROFILE TRADITIONAL

STRUCTURE STRUCTURE STRUCTURE
LP2
5

Table 25. Part Numbers for Figure 11

Item Part No. Qty. Part Name

Optional Selection -M1 (Painted Steel)
– N0141ZT – Mounting Set, steel (Items 1, 2, 3, and 4)
1 0011962 2 Nut, steel, 0.312-18
2 N0141ZW 1 Bracket, steel
3 D0114SM 1 U-Bolt, steel
4 X0100NW 4 Screw, hex head, steel, 0.437-20 x 0.625
5 D0170ME 1 Optional Standoff Kit with Four Steel Standoffs
(Not part of -M1 Option)
Optional Selection -M2 (Stainless Steel)
– N1205YD – Mounting Set, ss (Items 1, 2, 3, and 4)
1 Z1217HV 2 Nut, ss, 0.312-18
2 N1205MF 1 Bracket, ss
3 N1205MX 1 U-Bolt, ss
4 P0120RN 4 Screw, hex head, ss, 0.437-20 x 0.625
5 D0170MJ 1 Optional Standoff Kit with Four 316 ss Standoffs
(Not part of -M2 Option)

NOTE
For universal style mounting bracket, see Figure 12.
OPTIONAL SELECTIONS Page 27

Figure 12. Optional Universal Style Pipe Mounting Set Optional Selection -M3
mm
in
U-BOLT ASSEMBLY. BRACKET HOLES FOR
4 U-BOLT CAN ALSO BE USED FOR MOUNTING
THE BRACKET TO A SURFACE WITH USER
SUPPLIED HARDWARE.
HOLES FOR
U-BOLT AND
SURFACE 1
MOUNTING BOLTS FOR
ON FOUR MOUNTING
SIDES OF THIS 2 TRANSMITTER
BRACKET LEG, TO SURFACE

3
5
BOLTS FOR MOUNTING
TRANSMITTER TO BRACKET

ITEM 2 BOLTS CAN ALSO BE USED WITH THESE

HOLES TO MOUNT TRANSMITTER TO BRACKET

TYPICAL PIPE MOUNTING WITH LOW PROFILE STRUCTURE LP2

TYPICAL PIPE MOUNTING TYPICAL PIPE

LOW PROFILE MOUNTING WITH
STRUCTURE LP1 TRADITIONAL STRUCTURE

Table 26. Part Numbers for Figure 12

Item Part No. Qty. Part Name

– D0170XH 1 Universal Pipe Mounting Set (Items 1 to 4)
1 D0170VJ 1 Bracket, Universal Mounting, ss
2 X0173UR 2 Screw, hex head; ss; 0.375-16 x 1.5
3 A2012TZ 2 Washer, lock; 0.382 I.D.; ss
4 D0170VM 1 U-Bolt Kit:
U-Bolt; ss; 0.312-18
Clamp, saddle; ss
Page 28 OPTIONAL SELECTIONS

Table 26. Part Numbers for Figure 12

Item Part No. Qty. Part Name

Plate, washer; ss
Nut, hex head; ss; 0.312-18
5 P0120RN 4 Screw, hex head; 0.437-20 x 0.625; ss

Figure 13. Optional Conduit Connectors, Optional Selection -A1, -A2, -A3, or -A4

1 HAWKE-TYPE CABLE 2 NYLON CABLE 3 M20 CONDUIT 4 BRASS CABLE

GLAND (1/2 NPT) GLAND (PG 13.5) CONNECTION (1/2 NPT) GLAND (PG 13.5)

CABLE CABLE CABLE

GLAND M20 GLAND
GLAND
1/2 NPT PG 13.5
1/2 NPT PG 13.5

(-A1) (-A2) (-A3) (-A4)

Table 27. Part Numbers for Figure 13

Item Part No. Qty. Part Name

1 N7141HX 1 Hawke-Type Cable Gland (for 1/2 NPT)
2 X0178GU 1 Nylon Cable Gland (for PG 13.5)
3 N7141DX 1 Metric Conduit Thread Connection, M20/20 mm (for 1/2 NPT)
4 N7141DW 1 Plated Brass Cable Gland (for PG 13.5)

Figure 14. Optional Tubing Connector, Optional Selection -E3 or -E4

1 1/4 OR 1/2 NPT

TO PROCESS
CONNECTION
6 mm OR 12 mm TUBE

Table 28. Part Numbers for Figure 14

Item Part No. Qty. Part Name

1 Below – Process Connector,
U7002AS 316 ss, 640 bar (1/4 NPT x 6 mm), Optional Selection -E3
U7002AP 316 ss, 640 bar (1/2 NPT x 12 mm), Optional Selection -E4
OPTIONAL SELECTIONS Page 29

Figure 15. Optional Adapter Plate Kit, Optional Selections -P1 to -P8 for Direct Mount to Coplanar Manifolds
Available only With Low Profile Structures LP1 and LP2

LP1
STRUCTURE
SHOWN

1 TWO GASKETS
ADAPTER PLATE

2 TWO GASKETS

C0PLANAR
MANIFOLD
(REFERENCE)

HEX HEAD SCREWS

0.437-20 x 1.75 inches
FOUR PLACES

Table 29. Part Numbers for Figure 15, -P1 to -P4

Item Part No. Qty. Part Name

– D0170XJ 1 Adapter Plate Kit; B7 Screws; Option -P1
– D0170XM 1 Adapter Plate Kit; 316 ss Screws; Option -P2
– D0170XN 1 Adapter Plate Kit; 17-4 ss Screws; Option -P3
– D0170XP 1 Adapter Plate Kit; B7M Screws; Option -P4
*1 D0114RB 2 Gasket - Transmitter to Adapter Plate
*2 D0170XK 2 Gasket - Manifold to Adapter Plate

Table 30. Part Numbers for Figure 15, -P5 to -P8

Item Part No. Qty. Part Name

– D0170XQ 1 Adapter Plate Kit; B7 Screws; Option -P5
– D0170XR 1 Adapter Plate Kit; 316 ss Screws; Option -P6
– D0170XS 1 Adapter Plate Kit; 17-4 ss Screws; Option -P7
– D0170XT 1 Adapter Plate Kit; B7M Screws; Option -P8
*1 D0114RB 2 Gasket - Transmitter to Adapter Plate
*2 D0170XK 2 Gasket - Manifold to Adapter Plate

NOTE
1. Adapter Plate Kit Options -P1 and -P5 are not available with Bolting Options -B1, -B2, or -B3.
2. Adapter Plate Kit Options -P2 and -P6 require the use of Bolting Option -B1.
3. Adapter Plate Kit Options -P3 and -P7 require the use of Bolting Option -B2.
4. Adapter Plate Kit Options -P4 and -P8 require the use of Bolting Option -B3.
5. Items 1 and 2 are also part of Adapter Plate Kits.
Page 30 OPTIONAL SELECTIONS

Figure 16. Replacing Foxboro Models 823DP, 843DP, and 863DP with an IDP10 Transmitter

REPLACEMENT IDP10
TRANSMITTER FOUR HEXAGONAL
STANDOFFS PROVIDED
WITH STANDOFF KIT. THESE
MAY ALSO BE USED IN WALL
MOUNT INSTALLATIONS TO
PROCESS
PROVIDE EASIER ACCESS TO
CONNECTOR
VENT AND DRAIN SCREWS.

PIPE MOUNTING
BRACKET SET,
SEE FIGURE 9.

APPROXIMATE PLANE OF
PROCESS CONNECTOR
MOUNTING SURFACE; THE
ORIGINAL TRANSMITTER
BEING REPLACED AND
THE REPLACEMENT IDP10
USING THE STANDOFF KIT.

Table 31. Part Numbers for Figure 16

Kit Part Number for: (a)

Description of Transmitter being Replaced Steel Stainless Steel
2)
823DP with 20 MPa (3000 psi, 200 bar or kg/cm Static Pressure Rating D0170MB D0170MF
823DP with 40 MPa (6000 psi, 400 bar or kg/cm2) Static Pressure Rating D0170MC D0170MG
843DP or 863DP with Single Ended Cover D0170MD D0170MH
843DP or 863DP with Double Ended Cover D0170ME D0170MJ
a. The kit consists of four standoffs. Select steel if mounting screws in Figure 6 are steel, and select stainless steel if mounting screws in
Figure 6 are stainless steel.
OPTIONAL SELECTIONS Page 31

Figure 17. Optional SIL2 Transmitter for Hart Versions, Optional Selection -S2
ALWAYS A
SOLID COVER
ON THIS END 7 OPTION -S2

1 2
3
4

(SOLID
5 COVER
3
SHOWN)
1 2

SEE FIGURE 1
FOR OTHER PARTS

Table 32. Part Numbers for Figure 17

Item Part No. Qty. Part Name

1 Below 2 Cover, Electronics Housing (a)
D0162AP Solid Cover, Aluminum
D0162VD Solid Cover, Stainless Steel

2 X0118CC 1 Grease, Lubriplate; 1 3/4 ounce Tube

3 X0201FC 2 O-Ring, Cover

4 Below 4 Screw, Terminal Block Assy; 0.138-32 x 0.750

X0133UW Steel Screw used with Aluminum Housing
X0133VP 316 ss Screw used with 316 ss Housing

5 Below 2 Screw, Captive, Panhd; 0.118-32 x 0.615

D0162VM Steel Screw used with Aluminum Housing
D0166CY 316 ss Screw used with 316 ss Housing

6 X0144KR 1 O-Ring, Terminal Block

7 D0197FP 1 SIL2 Kit for SIL2-Certified HART Versions only (b)

a. A solid cover on the electronics end of the housing is shown. When the LCD Indicator Option.
(Option -L1) is selected, a window cover is provided as shown in Figure 3.
b. SIL2 Transmitters are available with HART versions. A SIL2 Kit comprises a terminal block
assembly, a characterized HART electronics module (with label), and instructions. Replacement of
SIL2 Option -S2 must be performed using the SIL2 kit.
Page 32 RECOMMENDED SPARE PARTS SUMMARY

RECOMMENDED SPARE PARTS SUMMARY

Number of Parts
Recommended For
Figure
Number Item Number Part Number Part Name 1 Inst. 5 Inst. 20 Inst.
1 3 X0201FC O-Ring, Cover 0 2 4
10 Below Electronics Module 0 1 1
D0162VR Digital FoxCom and/or 4 to 20 mA (Version -D)
D0150JC Digital FOUNDATION fieldbus (Version -F)
D0162VZ Digital HART and 4 to 20 mA (Version -T)
D0162ZP Analog 4 to 20 mA (Version -A)
D0162ZX Analog 1 to 5 V dc, Low Power (Version -V)
12(a) Sensor Assembly (Reference Model Code) 0 1 1
Below (for use with Traditional Structure)
D0175DA IDP10-..0A
D0175AA IDP10-..0B
D0175AD IDP10-..0C
D0175AG IDP10-..0D
D0175AK IDP10-..0E
D0175DG IDP10-..1A
D0175AN IDP10-..1B
D0175AR IDP10-..1C
D0175AU IDP10-..1D
D0175AX IDP10-..1E
D0175DB IDP10-..2A
D0175AB IDP10-..2B
D0175AE IDP10-..2C
D0175AH IDP10-..2D
D0175AL IDP10-..2E
D0175DF IDP10-.2GA
D0175BS IDP10-.2GB
D0175BT IDP10-.2GC
D0175BU IDP10-.2GD
D0175BV IDP10-.2GE
D0175DH IDP10-..3A
D0175AP IDP10-..3B
D0175AS IDP10-..3C
D0175AV IDP10-..3D
D0175AY IDP10-..3E
D0175DC IDP10-..4A
D0175BA IDP10-..4B
D0175BB IDP10-..4C
D0175BC IDP10-..4D
D0175BD IDP10-..4E
D0175DJ IDP10-..5A
D0175BE IDP10-..5B
D0175BF IDP10-..5C
D0175BG IDP10-..5D
D0175BH IDP10-..5E
RECOMMENDED SPARE PARTS SUMMARY Page 33

RECOMMENDED SPARE PARTS SUMMARY (Continued)

Number of Parts
Recommended For
Figure
Number Item Number Part Number Part Name 1 Inst. 5 Inst. 20 Inst.
1 (Cont.) 12(a) Sensor Assembly (Reference Model Code) (Cont.) 0 1 1
Below (for use with Traditional Structure)
D0175DD IDP10-..6A
D0175AC IDP10-..6B
D0175AF IDP10-..6C
D0175AJ IDP10-..6D
D0175AM IDP10-..6E
D0175DK IDP10-..7A
D0175AQ IDP10-..7B
D0175AT IDP10-..7C
D0175AW IDP10-..7D
D0175AZ IDP10-..7E
D0175DE IDP10-..8A
D0175BJ IDP10-..8B
D0175BK IDP10-..8C
D0175BL IDP10-..8D
D0175DL IDP10-..9A
D0175BN IDP10-..9B
D0175BP IDP10-..9C
D0175BQ IDP10-..9D
Sensor Assembly (Reference Model Code) 0 1 1
Below (for use with Low Profile Structures LP1 and LP2)
D0170WA IDP10-.LLA; IDP10-.52A
D0170WB IDP10-.LLB; IDP10-.52B
D0170WC IDP10-.LLC; IDP10-.52C
D0170WD IDP10-.LLD; IDP10-.52D
D0170WE IDP10-.LLE; IDP10-.52E
D0170WF IDP10-.LMA; IDP10-.53A
D0170WG IDP10-.LMB; IDP10-.53B
D0170WH IDP10-.LMC; IDP10-.53C
D0170WJ IDP10-.LMD; IDP10-.53D
D0170WK IDP10-.LME; IDP10-.53E
D0170WL IDP10-.LCA; IDP10-.56A
D0170WM IDP10-.LCB; IDP10-.56B
D0170WN IDP10-.LCC; IDP10-.56C
D0170WP IDP10-.LCD; IDP10-.56D
D0170WQ IDP10-.LCE; IDP10-.56E
D0170WR IDP10-.LDA; IDP10-.57A
D0170WS IDP10-.LDB; IDP10-.57B
D0170WT IDP10-.LDC; IDP10-.57C
D0170WU IDP10-.LDD; IDP10-.57D
D0170WV IDP10-.LDE; IDP10-.57E
2 1 Below O-Ring, Housing Neck 1 2 4
X0201LY Standard
X0144KW For use with CSA Certifications only.
3 1 Below O-Ring, Housing Neck 1 2 4
X0201LY Standard
X0144KW For use with CSA Certifications only.
Page 34

RECOMMENDED SPARE PARTS SUMMARY (Continued)

Number of Parts
Recommended For
Figure
Number Item Number Part Number Part Name 1 Inst. 5 Inst. 20 Inst.
4 4 Below Vent Screw 0 2 4
B0138MJ 316 ss (standard)
B0138MK Monel
D0175PQ Nickel Alloy (a) (to NACE Standard MR-01-75)
5 Below Vent Plug 0 2 4
D0161QT 316 ss (standard)
D0161QU Monel (to NACE Std. MR-01-75)
D0175PP Nickel Alloy (a) (to NACE Standard MR-01-75)
9 D0114RB Gasket, PTFE 2 2 4
10 Below Gasket 2 4 8
D0161QQ Glass-filled PTFE (standard)
X0145MJ Viton (used with Process Connector Code 7)
15 D0175TA Insert, PVDF (used with Process Connector Code 7) 2 4 8
5 4 Below Vent Screw (b) 0 2/4 4/8
B0138MJ 316 ss
D0175PQ Nickel Alloy (a)
5 Below Vent Plug (b) 0 2/4 4/8
D0161QT 316 ss
D0175PP Nickel Alloy (a)
9 D0114RB Gasket, PTFE 2 4 8
10 D0161QQ Gasket, Glass-filled PTFE 2 4 8
9 2 D0162LQ Indicator Module 0 1 1
15 1 D0114RB Gasket - Transmitter to Adapter Plate 2 4 8
2 D0170XK Gasket - Manifold to Adapter Plate 2 4 8
17 7 D0197FP SIL2 Kit for SIL2-Certified HART Transmitters 0 1 1

a. Equivalent to Hastelloy® C. Hastelloy is a registered trademark of Haynes International, Inc.

Invensys Systems, Inc. Copyright 1995-2015 Invensys Systems, Inc.

10900 Equity Drive All rights reserved.
Houston, TX 77041
United States of America Invensys, Foxboro, FoxCom, and I/A Series are trademarks
http://www.invensys.com of Invensys Limited, its subsidiaries, and affiliates. All other
trademarks are the property of their respective owners.
Global Customer Support
Inside U.S.: 1-866-746-6477 Invensys is now part of Schneider Electric.
Outside U.S.: 1-508-549-2424
Website: http://support.ips.invensys.com 0115