YSP-500_G-cv.

fm Page 1 Thursday, September 20, 2007 8:49 AM

YSP-500

YSP-500
Digital Sound ProjectorTM
Système Acoustique Numérique

OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
© 2007 All rights reserved. BRUKSANVISNING
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
GEBRUIKSAANWIJZING
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA Printed in Malaysia WM28790
CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

Caution: Read this before operating this unit.

1 To assure the finest performance, please read this manual 21 The batteries shall not be exposed to excessive heat such as
carefully. Keep it in a safe place for future reference. sunshine, fire or the like.
2 Install this sound system in a well ventilated, cool, dry, clean
WARNING
place with at least 5 cm (2 in) of space above (or below) this unit
– away from direct sunlight, heat sources, vibration, dust, TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
moisture, and/or cold. NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
3 Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds. WARNING
4 Do not expose this unit to sudden temperature changes from cold THE POWER SUPPLY CABLE OF THIS UNIT MUST BE
to hot, and do not locate this unit in an environment with high CONNECTED TO THE MAIN SOCKET OUTLET VIA A
humidity (i.e. a room with a humidifier) to prevent condensation PROTECTIVE EARTHING CONNECTION.
inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury. This unit is not disconnected from the AC power source as long as
5 Avoid installing this unit where foreign object may fall onto this it is connected to the AC wall outlet, even if this unit itself is
unit and/or this unit may be exposed to liquid dripping or turned off by STANDBY/ON. This state is called the standby
splashing. On the top of this unit, do not place: mode. In this state, this unit is designed to consume a very small
– Other components, as they may cause damage and/or quantity of power.
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage
FOR U.K. CUSTOMERS
to this unit, and/or personal injury.
If the socket outlets in the home are not suitable for the plug
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this supplied with this appliance, it should be cut off and an
unit. appropriate 3 pin plug fitted. For details, refer to the instructions
described below. Note that the plug severed from the mains lead
6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.
must be destroyed, as a plug with bared flexible cord is hazardous
in order not to obstruct heat radiation. If the temperature inside
if engaged in a live socket outlet.
this unit rises, it may cause fire, damage to this unit, and/or
personal injury. IMPORTANT
7 Do not plug in this unit to a wall outlet until all connections are THE WIRES IN MAINS LEAD ARE COLOURED IN
complete. ACCORDANCE WITH THE FOLLOWING CODE:
8 Do not operate this unit upside-down. It may overheat, possibly Blue: NEUTRAL
causing damage. Brown: LIVE
9 Do not use force on switches, knobs and/or cords. As the colours of the wires in the mains lead of this apparatus may
10 When disconnecting the power supply cable from the wall outlet, not correspond with the coloured markings identifying the
grasp the plug; do not pull the cable. terminals in your plug, proceed as follows:
11 Do not clean this unit with chemical solvents; this might damage The wire which is coloured BLUE must be connected to the
the finish. Use a clean, dry cloth. terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
12 Only voltage specified on this unit must be used. Using this unit
terminal which is marked with the letter L or coloured RED. Make
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. Yamaha will not sure that neither core is connected to the earth terminal of the three
be held responsible for any damage resulting from use of this unit pin plug.
with a voltage other than specified.
13 To prevent damage by lightning, keep the power supply cable CAUTION
disconnected from a wall outlet or this unit during a lightning Danger of explosion if battery is incorrectly replaced. Replace
storm. only with the same or equivalent type.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. CAUTION
The cabinet should never be opened for any reasons. Use of controls or adjustments or performance of procedures other
15 When not planning to use this unit for long periods of time (i.e. than those specified herein may result in hazardous radiation
vacation), disconnect the power supply cable from the wall exposure.
outlet.
16 Be sure to read the “Troubleshooting” section on common This symbol mark is according to the
operating errors before concluding that this unit is faulty. EU directive 2002/96/EC.
17 Before moving this unit, press STANDBY/ON to set this unit in
standby mode, and disconnect the power supply cable from the This symbol mark means that electrical
wall outlet. and electronic equipment, at their end-
18 Condensation will form when the surrounding temperature of-life, should be disposed of separately
changes suddenly. Disconnect the power supply cable from the from your household waste.
outlet, then leave the unit alone. Please act according to your local rules
19 When using the unit for a long time, the unit may become warm. and do not dispose of your old products
Turn the power off, then leave the unit alone for cooling. with your normal household waste.
20 Install this unit near the AC outlet and where the AC power plug
can be reached easily.

i En
 Contents
Enjoying stereo sound...........................................50

INTRODUCTION
INTRODUCTION Playing back sound clearly (My Beam)...............51
Overview.................................................................. 2 Using auto-adjust function....................................... 51
Features ................................................................... 3 Using manual-adjust function.................................. 52
Using this manual ................................................... 5 Using the volume mode
Supplied accessories ............................................... 6 (Night listening enhancer/TV volume equal
Controls and functions ........................................... 7 mode) ..................................................................53
Front panel ................................................................. 7 Using the sleep timer.............................................54
Front panel display .................................................... 8
Rear panel .................................................................. 9

PREPARATION
Remote control......................................................... 10 ADVANCED OPERATION
MANUAL SETUP.................................................56
PREPARATION Using MANUAL SETUP ........................................ 57
BEAM MENU ......................................................... 58
Installation............................................................. 13 SOUND MENU....................................................... 62
Before installing this unit......................................... 13 INPUT MENU......................................................... 64
Installing this unit .................................................... 13 DISPLAY MENU.................................................... 66
Connections ........................................................... 16 Adjusting the audio balance.................................67
Before connecting components................................ 17 Using the test tone ................................................... 67
Connecting a TV...................................................... 18 Using the audio output being played back............... 68
Connecting a DVD player/recorder ......................... 19 Selecting the input mode.......................................70

SETUP
Connecting a digital satellite tuner Adjusting the system parameters ........................71
or a cable TV tuner .............................................. 20 Using the system parameters ................................... 71
Connecting a digital airwave tuner .......................... 21 Setting the MEMORY PROTECT .......................... 72
Connecting a VCR................................................... 22 Setting the MAX VOLUME.................................... 73
Connecting other external components ................... 23 Setting the TURN ON VOLUME ........................... 73
Connecting a subwoofer .......................................... 24 Setting the DEMO MODE ...................................... 74
Connecting the AC power supply cable .................. 25 Setting the PANEL INP. KEY ................................ 75
Disabling the front panel keys ................................. 76
Setting the FACTORY PRESET ............................. 77

OPERATION
SETUP Remote control features........................................79

BASIC
Setting remote control codes ................................... 79
Getting started ...................................................... 26
Controlling other components ................................. 80
Installing batteries in the remote control ................. 26
Using the TV macro ................................................ 83
Operation range of the remote control..................... 26
Turning on this unit or setting it to the standby mode
............................................................................. 27
ADDITIONAL INFORMATION
Using SET MENU................................................. 28
Displaying the OSD (on-screen display) ................. 28 Troubleshooting.....................................................85
The flow chart of SET MENU................................. 29 Glossary..................................................................88
Changing OSD language ...................................... 30 Index .......................................................................90

OPERATION
ADVANCED
AUTO SETUP (IntelliBeam) ............................... 31 Specifications .........................................................91
The flow chart of AUTO SETUP ............................ 31
Installing the IntelliBeam microphone .................... 32
Using AUTO SETUP (IntelliBeam)........................ 33 List of remote control codes ...........................................i
Using the system memory .................................... 38
Convenient usage of the system memory ................ 38
Saving settings ......................................................... 38
Loading settings....................................................... 39
INFORMATION
ADDITIONAL

BASIC OPERATION
Playback ................................................................ 41
Selecting the input source........................................ 41
Playing back sources................................................ 42
Adjusting the volume............................................... 43
Enjoying surround sound .................................... 44
5 Beam ..................................................................... 44
Stereo plus 3 Beam .................................................. 45
3 Beam ..................................................................... 45
English

My Surround............................................................ 45
Enjoying 2-channel sources in surround sound ....... 47
Enjoying TV in surround sound .............................. 48
Adjusting surround mode parameters...................... 49

1 En
Overview

Overview
It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of
wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of
surround sound experience as your local movie theater.
Yamaha YSP-500 Digital Sound Projector challenges this preconception that complicated speaker setup and troublesome
wiring go hand-in-hand with the enjoyment of multi-channel surround sound.
This slimline unit does away with the need for complicated wiring and installation worries, leaving you with a unit that is
not only easy to set up, but is also capable of reproducing the kind of powerful surround sound you have been waiting for
from its built-in 2 woofers and 16 full-range small speakers.
You can fine-tune the parameters of this unit to adjust the delay time for separate sound beams, resulting in highly
directional sound that comes in on the listening position from all directions.
The YSP-500 projects sound beams containing surround sound information for the front right (R), front left (L), surround
right (SR), and surround left (SL) speaker positions, which are reflected off the walls of your listening room before
reaching the actual listening position. With the addition of center (C) sound beams, this Digital Sound Projector creates
true-to-life 5.1-channel surround sound that makes you feel as if there are actual speakers around the room.
Sit back and enjoy the real sound experience of this simple, yet stylish Digital Sound Projector.

Imaginary
front right
speaker

C
SR
L
SL

Imaginary
surround right
Imaginary speaker
front left
speaker

Imaginary Listening position

center
speaker

Imaginary
surround left
speaker

2 En
 Features

Features
Digital Sound Projector™ Compatibility with the Newest Technologies

INTRODUCTION
The Digital Sound Projector technology allows one slim This unit employs decoders compatible with Dolby
unit to control and steer multiple channels of sound to Digital, DTS, Dolby Pro Logic, Dolby Pro Logic II, and
generate multi-channel surround sound, thus eliminates DTS Neo:6.
the need for satellite loudspeakers and cabling normally ◆ Dolby Digital
associated with conventional surround sound systems. This is the standard audio signal format used on various
This unit also employs the beam modes that let you enjoy digital media such as DVD, Blu-ray, and HD DVD. This
the surround sound (5 Beam, Stereo plus 3 Beam, 3 Beam, surround technology delivers high-quality digital audio for up
to 5.1 discrete channels to produce a directional and more
and My Surround), stereo playback, and My Beam.
realistic effect.
My Surround ◆ DTS
In addition to the above mentioned beam modes, this unit This is the standard audio signal format used on various
digital media such as DVD, Blu-ray, and HD DVD. This
is equipped with My Surround beam mode that allows you
surround technology delivers high-quality digital audio for up
to enjoy surround system even in a small listening area.
to 5.1 discrete channels to produce a directional and more
My Beam realistic effect.
◆ Dolby Pro Logic
This unit employs My Beam that ensures a clear sound in
This sophisticated, matrix decoding technology up-converts
a noisy environment. You can adjust the beam angle
any 2-channel source audio to a 5.1-channel full bandwidth
manually or automatically using the supplied remote playback, resulting in a surround sound experience.
control to the maximum of 30°, rightward and leftward. ◆ Dolby Pro Logic II
Versatile Remote Control This is a redesigned version of Dolby Pro Logic that employs
2 stereo surround channels, a subwoofer, and a greatly
The supplied remote control comes with preset remote enhanced steering logic. This improved technology provides
control codes used to control the DVD player, VCR, cable an exceptionally stable sound field that simulates 5.1 to a
TV tuner, and digital satellite tuner connected to this unit. much greater degree than the original Dolby Pro Logic.
In addition, the remote control is equipped with the macro ◆ DTS Neo:6
capability that enables a series of operations with the press This technology decodes the conventional 2-channel sources
of a single button. for 6-channel playback, enabling playback with the full-range
channels with higher separation. Music mode and Cinema
AUTO SETUP (IntelliBeam) mode are available to play back music and movie sources
This unit employs the automatic sound beam and acoustic respectively.
optimization technology with the aid of the supplied
IntelliBeam microphone. You can avoid troublesome
listening-based speaker setup and achieve highly accurate
sound beam adjustments that best match your listening
environment.

English

3 En
Features

The “ ” logo and “IntelliBeam” are trademarks of

YAMAHA Corporation.
TruBass, SRS and the “ ” symbol are registered trademarks
of SRS Labs, Inc. TruBass technology is incorporated under
license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks ™ is a trademark of DiMAGIC Co., Ltd.
of Dolby Laboratories.

“DTS” and “Neo:6” are registered trademarks of DTS, Inc.

Manufactured under license from 1 Ltd. Worldwide patents

applied for.
The “ ” logo and “Digital Sound Projector™” are trademarks
of 1 Ltd.

4 En
 Using this manual

Using this manual

Notes

INTRODUCTION
• This manual describes how to connect and operate this unit. For details regarding the operation of external components, refer to the
supplied owner’s manual for each component.
• Operations in this manual use keys on the supplied remote control of this unit unless otherwise specified.
• y indicates a tip for your operation.
• This manual is printed prior to production. Designs and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and the product, the product has priority.

1 Install this unit in your listening room.

See “Installation” on page 13.

2 Connect this unit to your TV and other external components.

See “Connections” on page 16.

3 Prepare the remote control and turn on the power of this unit.
See “Getting started” on page 26.

4 Run AUTO SETUP.

See “AUTO SETUP (IntelliBeam)” on page 31.

5 Play back a source.

See “Playback” on page 41.

6 Change the beam modes.

See “Enjoying surround sound” on page 44.

If you want to make additional settings

and adjustments
English

7 Run MANUAL SETUP to fine-tune settings and/or set remote control codes.
See “MANUAL SETUP” on page 56 and “Remote control features” on page 79.

5 En
Supplied accessories

Supplied accessories
Check that you have received all of the following parts.

Remote control (×1) Cable clamp (×1) Optical cable (×1)

STANDBY/ON POWER POWER

AV TV

STB VCR DVD AUX

TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
IntelliBeam microphone
5BEAM ST+3BEAM 3BEAM (×1)
1 2 3 Digital audio pin cable (×1)
STEREO MY BEAM MY SUR.

4 5 6

7 8 9
SUR. DECODE

0 +10

CH LEVEL MENU (Orange)

TV/AV
ENTER
YSP
Cardboard microphone
TEST RETURN stand (×1)
VOLUME CH TV VOL Audio pin cable (×1)

MUTE TV INPUT TV MUTE

CODE SET

(White/Red)

Indoor FM antenna (×1)

OSD* video pin cable (×1)

Demonstration DVD (Yellow)

Batteries (×2)
(AA, R6, UM-3) (×1)
*OSD: On-Screen Display

QUICK REFERENCE
GUIDE

* The number of provided languages

varies depending on the model.

6 En
 Controls and functions

Controls and functions

INTRODUCTION
Front panel

INTELLIBEAM MIC INPUT VOLUME STANDBY/ON

1 2 3 4 5 6

1 INTELLIBEAM MIC jack 5 VOLUME +/–

Connect the supplied IntelliBeam microphone for AUTO Controls the volume level of all audio channels (see
SETUP (see page 32). page 43).
2 Front panel display 6 STANDBY/ON
Shows information about the operational status of this Turns on the power of this unit or sets it to the standby
unit. mode (see page 27).
3 Remote control sensor Notes
Receives infrared signals from the remote control.
• When you turn on this unit, you will hear a click sound
4 INPUT followed by the 4 to 5-second interval before sound
Press repeatedly to switch between input sources (see reproducing.
page 41). • In the standby mode, this unit consumes a small amount of
Outputs a test tone to experience the sound beam (see power in order to receive infrared signals from the remote
control.
page 74).

English

7 En
Controls and functions

Front panel display

1 2 3 4 5 6 7 8

1 SRS TruBass indicator 7 MULTI indicator

Lights up when TruBass is turned on (see page 63). Lights up when this unit detects a multi channel digital
audio signal.
2 EQUAL indicator
Lights up when the TV volume equal mode is selected 8 Volume level indicator
(see page 53). Displays the current volume level.
3 NIGHT indicator 9 Multi-information display
Lights up when one of the night listening enhancers is Shows information with alphanumeric characters when
selected (see page 53). you adjust the parameters of this unit.
4 SLEEP indicator y
Lights up when the sleep timer is set (see page 54). You can adjust the brightness and display setting of the front
panel display using the F.DISPLAY SET parameter in MANUAL
5 Decoder indicators SETUP (see page 66).
Light up when the corresponding decoder operates
(see page 46).
6 PCM indicator
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) digital audio signals.

8 En
 Controls and functions

Rear panel

INTRODUCTION
9

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

1 2 3 4 5 6 7 8

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

1 VCR AUDIO INPUT jacks 6 AUX OPTICAL DIGITAL INPUT jack

Connect your VCR via an analog connection (see Connect an external component via an optical digital
page 19). connection (see page 23).
2 TV/STB AUDIO INPUT jacks 7 DVD COAXIAL DIGITAL INPUT jack
Connect your TV, digital satellite tuner, or cable TV tuner Connect your DVD player via a coaxial digital connection
via an analog connection (see pages 18 and 20). (see page 19).
3 SUBWOOFER OUT jack 8 SYSTEM CONNECTOR jack
Connect your subwoofer (see page 24). Use to connect a Yamaha subwoofer equipped with a
SYSTEM CONNECTOR jack to this unit (see page 24).
4 VIDEO OUT jack
Connect to the video input jack of your TV to display the 9 AC power supply cable
OSD of this unit (see page 18). Connect to the AC wall outlet (see page 25).
5 TV/STB OPTICAL DIGITAL INPUT jack
Connect your TV, digital satellite tuner, or cable TV tuner
via an optical digital connection (see pages 18 and 20).
English

9 En
Controls and functions

Remote control
This section describes the functions of the remote control 1 Infrared window
used to control this unit. Some buttons marked with an Outputs infrared control signals. Aim this window at the
asterisk (*) share the common functions between the YSP component you want to operate.
and TV/AV operation modes (N).
2 STANDBY/ON
y Turns on the power of this unit or sets it to the standby
You can also control other components using the remote control
mode (see page 27).
once you set the appropriate remote control codes. See
“Controlling other components” on page 80 for details. 3 Transmission indicator
Lights up when infrared control signals are being output.
1 D 4 Input selector buttons
Use to select an input source (STB, VCR, DVD, AUX, or
STANDBY/ON POWER POWER TV).
*2
3
AV TV E*
F* 5 VOL MODE
Turns on or off the volume modes (see page 53).
STB VCR DVD AUX
6 AUTO SETUP
*4 INPUT1
TV
INPUT2 MACRO G*
TV H Enters the AUTO SETUP menu (see page 31).
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5 I 7 CH LEVEL
6 J
5BEAM ST+3BEAM 3BEAM

1 2 3
Adjusts the volume level of each channel (see page 68).
STEREO MY BEAM MY SUR. K
4 5 6 8 Cursor buttons / / / , ENTER
Select and adjust SET MENU items.
7 8 9
SUR. DECODE
9 TEST
0 +10 L
Outputs a test tone when adjusting the output level of each
CH LEVEL MENU

7 M channel (see page 67).

0 VOLUME +/–
8
TV/AV
ENTER
N
YSP
Increases or decreases the volume level of this unit (see
TEST RETURN

9 O page 43).
VOLUME CH TV VOL
A MUTE
P Mutes the sound. Press again to restore the audio output to
*0 the previous volume level (see page 43).
Q
*A MUTE TV INPUT TV MUTE

R
B TV INPUT
*B CODE SET Toggles between the input sources on the TV (see
page 80).
C
C DVD player/VCR control buttons
Control your DVD player or VCR (see pages 81 and 82).
D My Beam microphone
Collects the test tones from this unit when using the My
Beam auto-adjust function (see page 51).
E TV POWER
Turns on the power of your TV or sets it to the standby
mode (see page 80).
F AV POWER
Turns on the power of the selected component or sets it to
the standby mode (see pages 81 and 82).
G INPUT1/INPUT2
Switches the input source on your TV (see page 80).

10 En
 Controls and functions

H MACRO
Use to set the TV macro (see page 83).
I SLEEP

INTRODUCTION
Sets the sleep timer (see page 54).
J INPUTMODE
Toggles between input modes (AUTO, DTS, and
ANALOG) (see page 70).
K Beam mode buttons
Change the beam mode settings (see pages 44, 50, and
51).
L SUR. DECODE
Selects the surround mode for playback (see page 47).
M MENU
Displays the setup menu on your TV monitor (see
pages 33 and 57).
N Operation mode selector
Selects the operation mode of this unit. Select YSP when
operating this unit and select TV/AV when operating your
TV or other AV components.
O RETURN
Returns to the previous SET MENU screen.
P TV VOL +/–
Adjusts the volume level of your TV (see page 80).
Q CH +/–
Changes the channels of your TV, digital satellite tuner,
cable TV tuner, or VCR (see pages 80 and 82).
R TV MUTE, CODE SET
Mutes the audio output of your TV (see page 80).
Sets up remote control codes (see page 79).

English

11 En
Controls and functions

This section describes the functions of the remote control 1 Numeric buttons
used to control other components when the TV/AV mode Enter numbers.
is selected with the operation mode selector (4).
2 Cursor buttons / / / , ENTER
Use to select DVD menu items.
STANDBY/ON POWER POWER 3 MENU
AV TV
Displays the DVD menu.
4 Operation mode selector
STB VCR DVD AUX
Selects the operation mode of this unit. Select YSP when
INPUT1
TV
INPUT2 MACRO operating this unit and select TV/AV when operating your
TV
AUTO TV or other AV components.
VOL MODE SETUP INPUTMODE SLEEP

5BEAM ST+3BEAM 3BEAM

5 RETURN
1 2 3 Use to return to the previous DVD menu screen or exit
STEREO MY BEAM MY SUR.
from the DVD menu.
1 4 5 6

7 8 9
SUR. DECODE

0 +10

CH LEVEL MENU

3
2
ENTER
TV/AV
4
YSP
TEST RETURN

5
VOLUME CH TV VOL

MUTE TV INPUT TV MUTE

CODE SET

12 En
 Installation

Installation
This section describes a suitable installation location to install this unit using a rack.
Depending on your installation environment, connections with external components can be done before installing this
unit. We recommend that you temporarily place and arrange all components, including this unit, in order to decide which
procedure should come first.

Before installing this unit Installing this unit

This unit creates surround sound by reflecting projected Install this unit where there are no obstacles such as
sound beams off the walls of your listening room. The furniture obstructing the path of sound beams. Otherwise,

PREPARATION
surround sound effects produced by this unit may not be the desired surround sound effects may not be achieved.
sufficient when this unit is installed in the following You may install this unit in parallel with the wall or in the
locations. corner.
• Rooms with walls inadequate for reflecting sound
Parallel installation
beams
• Rooms with acoustically absorbent walls Install this unit in the exact center of the wall when it is
• Rooms with measurements outside the following measured from the left and right corners.
range: W (3 to 7 m (10 to 23 ft)) x H (2 to 3.5 m (7 to
11.5 ft)) x D (3 to 7 m (10 to 23 ft))
• Rooms with less than 1.8 m (6 ft) from the listening
position to this unit
• Rooms where objects such as furniture are likely to
obstruct the path of sound beams
• Rooms where the listening position is close to the walls
• Rooms where the listening position is not in front of
this unit
An object, such as furniture
y
• You can enjoy surround sound by selecting My Surround (see
Corner installation
page 45) as the beam mode even if your listening room may not
fulfill the above conditions (except when the listening position Install this unit in the corner at a 40º to 50º angle from the
is not directly facing toward the front of this unit). adjacent walls.
• You can also enjoy surround sound by selecting stereo playback
40° to 50°
(see page 50) or My Beam (see page 51) as the beam mode even
if your listening room may not fulfill the above conditions.
Make sure you leave an adequate amount of ventilation
space so that heat can escape. Make at least 5 cm (2 in) of
space above this unit.
Notes
• We do not recommend putting this unit directly on the floor of
your listening room. Please install this unit using a rack.
• This unit weights 8.5 kg (18 lbs 12 oz). Be sure to install this An object, such as furniture
unit where it will not fall subject to vibrations, such as from an
earthquake, and where it is out of the reach of children.
• When using a cathode-ray tube (CRT) TV, do not install this
unit directly above your TV.
• This unit is shielded against magnetic rays. However, if the
picture on your TV screen becomes blurred or distorted, we
recommend moving this unit away from your TV.
English

13 En
Installation

■ Installation examples
Example 1
Install this unit as close to the exact center of the wall as possible.

Example 2
Install this unit so that the sound beams can be reflected off the walls.

Example 3
Install this unit as close to the exact front of your normal listening position as possible.

14 En
 Installation

■ Using a rack
Install this unit under your TV in a commercially available
rack.

This unit

PREPARATION
Note
Make sure that the rack is large enough to allow adequate
ventilation space around this unit (see page 13) and that it is
strong enough to support the weight of both this unit and your TV.

English

15 En
Connections

Connections
This unit is equipped with the following types of audio/video input/output jacks/terminal:
For audio input For audio output
• 2 optical digital input jacks • 1 subwoofer output jack
• 1 coaxial digital input jacks
For video output
• 2 sets of analog input jacks
• 1 analog output jack

Use these jacks/terminal to connect external components such as your TV, DVD player, VCR, digital satellite tuner, cable
TV tuner, digital air wave tuner, and game console. Further, by connecting a subwoofer to this unit, you can enjoy
reinforced low-bass sounds. For details on how to connect various types of external components to this unit, see pages 18
to 24.
CAUTION
• Do not connect this unit or other components to the mains power until all connections between components are
complete.
• Unplug the AC power supply cable before changing connections, moving or cleaning this unit.

Audio connection

Video connection
TV

This unit

DVD player Subwoofer Digital satellite tuner VCR or game console

or cable TV tuner

16 En
 Connections

Before connecting components

■ Cables used for connections ■ Notes on connecting the optical cable
• Pull out the cap before connecting the optical cable.
Audio When you are not using the optical cable, be sure to put
Audio pin cable (supplied) the cap back in place.
• When inserting the cable into the optical digital jack,
(White) (White) make sure the direction is correct.

(Red) (Red)

PREPARATION
Cap
Optical cable (supplied)
■ Affixing cables
To prevent cables from becoming unplugged, place the
supplied cable clamp with the open side facing upward,
Digital audio pin cable (supplied) attach it to the rear panel of this unit in a suitable position,
and then affix cables in the cable clamp.
(Orange) (Orange)
Optical cable

Subwoofer pin cable Attach to this unit

5 System connector cable

Video

OSD video pin cable (supplied)

(Yellow) (Yellow)

English

17 En
Connections

Connecting a TV
For audio connection, connect the analog audio output jacks on your TV to the TV/STB AUDIO INPUT jacks on this
unit. If your TV has an optical digital output jack, connect the optical digital output jack on your TV to the TV/STB
OPTICAL DIGITAL INPUT jack on this unit.
For video connection, connect the video input jack on your TV to the VIDEO OUT jack on this unit to display the OSD
for easy viewing when you adjust the system parameters in SET MENU.

y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 17).

Note
If you make analog and optical digital audio connections at the same time as shown in the illustration below, the digital audio signals
input at the TV/STB OPTICAL DIGITAL INPUT jack take priority over the analog audio signals input at the TV/STB AUDIO INPUT
jacks.

Rear panel of this unit

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

R L
Analog Video Optical
audio input digital
output output

TV

Video Audio

OSD video pin cable Audio pin cable

Optical cable

18 En
 Connections

Connecting a DVD player/recorder

Connect the coaxial digital output jack on your DVD player/recorder to the DVD COAXIAL DIGITAL INPUT jack on
this unit. When you connect this unit to your DVD/VCR combo player/recorder, connect the analog audio output jacks on
your DVD/VCR combo player/recorder to the VCR AUDIO INPUT jacks on this unit in addition to the coaxial digital
audio connection.
y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 17).

Notes
• Check that your DVD player/recorder is properly set to output Dolby Digital and DTS digital audio signals. If not, adjust the system

PREPARATION
settings of your DVD player/recorder. For details, refer to the operation manual supplied with your DVD player/recorder.
• If your DVD player/recorder does not have a coaxial digital output jack, make an optical digital audio connection instead (see
page 23).

Rear panel of this unit

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

* For the DVD/VCR combo

player/recorder
connection

R L
Analog Coaxial
audio digital
output output

Video signal to the TV DVD player/recorder

Audio

Audio pin cable

Digital audio pin cable

English

19 En
Connections

Connecting a digital satellite tuner or a cable TV tuner

Connect the optical digital output jack on your digital satellite tuner or cable TV tuner to the TV/STB OPTICAL
DIGITAL INPUT jack on this unit. Connect the analog audio output jacks on your digital satellite tuner or cable TV
tuner to the TV/STB AUDIO INPUT jacks on this unit.
y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 17).

Rear panel of this unit

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

R L
Analog Optical
audio digital
output output

Video signal to the TV Digital satellite tuner

* This connection (except for a game console) is not or cable TV tuner
necessary if your TV has a built-in digital satellite
tuner, cable TV tuner, or digital airwave tuner.

Audio

Audio pin cable

Optical cable

20 En
 Connections

Connecting a digital airwave tuner

Connect the TV/STB AUDIO INPUT jacks on this unit to the analog audio output jacks on your TV. Connect the optical
digital output jack on your digital airwave tuner to the TV/STB OPTICAL DIGITAL INPUT jack on this unit in addition
to the analog audio connection. By doing so, you can enjoy both analog and digital broadcasts.
y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 17).

Rear panel of this unit

PREPARATION
L

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

Connect to the analog

audio output jacks on
the TV. Optical
digital
output

* This connection (except for a game console) is not

necessary if your TV has a built-in digital satellite
tuner, cable TV tuner, or digital airwave tuner.

Digital airwave tuner Video signal to the TV

Audio

Audio pin cable

Optical cable
English

21 En
Connections

Connecting a VCR
To connect a VCR, connect the analog audio output jacks on your VCR to the analog audio input jacks (VCR L/R) on
this unit.
Connect red plugs to the right jacks and white plugs to the left jacks.

Rear panel of this unit

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

R L
Analog
audio
output

VCR Video signal to the TV

Audio

Audio pin cable

22 En
 Connections

Connecting other external components

If your component supports optical digital connections, connect the optical digital output jack on your component
(e.g., DVD player/recorder) to the AUX OPTICAL DIGITAL INPUT jack on this unit.
y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 17).

Rear panel of this unit

PREPARATION
R

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

Optical
digital
output

Video signal to the TV DVD player/recorder,

game console, CD player, etc.

Audio

Optical cable
English

23 En
Connections

Connecting a subwoofer
Connect the monaural input jack on your subwoofer to the SUBWOOFER jack on this unit.
This connection alone does not output sound from the connected subwoofer. To output sound from the connected
subwoofer, turn on the power of your subwoofer and then run AUTO SETUP (see page 31) or select SWFR for BASS
OUT in SUBWOOFER SET (see page 62).
When connecting a Yamaha subwoofer equipped with a SYSTEM CONNECTOR terminal, connect it to the SYSTEM
CONNECTOR terminal on this unit. If the subwoofer is connected using a system type connection, changing the power
mode of this unit controls the power mode of the subwoofer.

Rear panel of this unit

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

4 5

Monaural System
input connector

Subwoofer

Audio

Subwoofer pin cable

5 System connector cable

24 En
 Connections

Connecting the AC power supply cable

Once all other connections are complete, plug the AC power supply cable into the AC wall outlet.

PREPARATION
To the AC wall outlet

English

25 En
GETTING STARTED

Getting started
y
Installing batteries in the remote Remove the transparent sheet before using the remote control.

control

Press

Operation range of the remote

control
The remote control transmits a directional infrared beam.
Use the remote control within 6 m (20 ft) of this unit and
point it toward the remote control sensor of this unit
1 Press and hold the mark on the battery during operation.
cover and then open the cover.

2 Insert the two supplied batteries (AA, R6,

UM-3) into the battery compartment.
Make sure you insert the batteries according to the
polarity markings (+/–). Approximately
6 m (20 ft)
30 30
3 Close the battery cover.

Notes
• Change all of the batteries if you notice the following
conditions: the operation range of the remote control decreases
or the transmission indicator does not light up or becomes dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as Notes
these different types of batteries may have the same shape and
• Do not spill water or other liquids on the remote control.
color.
• Do not drop the remote control.
• Exhausted batteries may leak. If the batteries have leaked,
• Do not leave or store the remote control in the following places:
dispose of them immediately. Avoid touching the leaked
– places of high humidity, such as near a bath
material or letting it come into contact with clothing, etc. Clean
– places of high temperatures, such as near a heater or a stove
the battery compartment thoroughly before installing new
– places of extremely low temperatures
batteries.
– dusty places
• Do not throw away batteries with general house waste. Dispose
• Do not expose the remote control sensor of this unit to direct
of them correctly in accordance with your local regulations.
sunlight or lighting such as inverted fluorescent lamps.
• The memory stored in the remote control may be erased in the
• If the batteries grow old, the effective operation range of the
following cases:
remote control decreases considerably. If this happens, replace
– The remote control is left without batteries for more than two
the batteries with two new ones as soon as possible.
minutes.
– Exhausted batteries remain in the remote control.
– The buttons on the remote control are accidentally pressed
when you change batteries.
• If the memory stored in the remote control is unwantedly
erased, insert new batteries and set the remote control codes
again.

26 En
 Getting started

Turning on this unit or 2 Press STANDBY/ON again to set this unit to

setting it to the standby mode the standby mode.

Note
When this unit is in the standby mode, only STANDBY/ON on
the front panel or on the remote control is operational, and the
other control buttons on the front panel or on the remote control
are not operational until the power of this unit is turned on.

INPUT VOLUME STANDBY/ON

STANDBY/ON POWER POWER

AV TV

STB VCR DVD AUX

TV
INPUT1 INPUT2 MACRO
TV

SETUP
1 Press STANDBY/ON to turn on the power of
this unit.
The volume level appears in the front panel display,
and the current input source and beam mode are
displayed.

STANDBY/ON

or
STANDBY/ON

Front panel Remote control

XXVOLUMEXX30XX
Current volume level

XXDVDXXXMYXSUR
Current input Current beam
source mode
English

27 En
USING SET MENU

Using SET MENU

Displaying the OSD (on-screen display)

This section describes how to display the OSD (on-screen display) of this unit on your TV screen and to set the
parameters for your listening room. Once this is complete, you can enjoy real surround sound while watching TV in the
comfort of your own home.

1 Check that the video input jack on your TV is 3 Turn on the power of your TV.
connected to the VIDEO OUT jack on this unit The following screen appears on your TV.
to display the OSD of this unit.

2 Press STANDBY/ON to turn on the power of YSP-500

this unit.

STANDBY/ON

or
Push [MENU] to begin set-up
STANDBY/ON

Front panel Remote control OSD screen example

If the OSD does not appear, use the remote control

supplied with your TV to switch the video input until
the OSD appears.

28 En
 Using SET MENU

The flow chart of SET MENU

The following diagram illustrates the overall flow of the setup procedure.

Run LANGUAGE SETUP.

See “Changing OSD language” on page 30.

Run AUTO SETUP (IntelliBeam).

See “AUTO SETUP (IntelliBeam)” on page 31.

If an error occurs

SETUP
Look for a remedy.
See “Error messages for AUTO SETUP” on page 37 for a complete list of error
messages and possible remedies.

Play back audio signals or adjust the settings for the beam mode.
See “Playback” on page 41, “Enjoying surround sound” on page 44.

If you want to make additional settings

and adjustments

Run MANUAL SETUP.

See “MANUAL SETUP” on page 56.
y
• If you cannot clearly hear a sound beam from a specific channel, adjust settings for
SETTING PARAMETERS (see page 58) or for BEAM ADJUSTMENT (see page 59) in
BEAM MENU.
• If there are acoustically absorbent objects such as curtains in the path of the sound beams,
adjust settings for TREBLE GAIN in BEAM MENU (see page 61).
English

29 En
CHANGING OSD LANGUAGE

Changing OSD language

This feature allows you to select the language of your choice that appears in SET MENU of this unit.

1 Set the operation mode selector to YSP. 4 Press / to select the desired language,
and press ENTER.
TV/AV
YSP

ENTER
ENTER

2 Press MENU.
The SET MENU screen appears on your TV.
Choices: ENGLISH (English), DEUTSCH (German),
SET MENU Français (French), ESPAÑOL (Spanish),
ITALIANO (Italian), NEDERLANDS (Dutch),
. ;MEMORY
MENU ;AUTO SETUP Русский (Russian)
;MANUAL SETUP
;LANGUAGE SETUP
[ ]/[ ]:Up/Down
p

[ENTER]:Enter

y
• The control buttons used for SET MENU are displayed at
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN.
• To exit from SET MENU, press MENU once more.
• You can also perform the following operations while
viewing information in the front panel display.

3 Press / to select LANGUAGE SETUP,

and press ENTER.
The following screen appears on your TV.

ENTER
ENTER

;LANGUAGE SETUP
. ENGLISH
DEUTSCH
Francais
ESPANOL
ITALIANO
NEDERLANDS

[ ]/[ ]:Select
p

[ENTER]:Return

30 En
 AUTO SETUP (INTELLIBEAM)

AUTO SETUP (IntelliBeam)

This unit creates a sound field by reflecting sound beams on the walls of your listening room and by broadening the
cohesion of all the channels. Just as you would arrange the speaker position of other audio systems, you need to set the
beam angle to enjoy the best possible sound from this unit.
This unit employs the beam optimization and sound optimization features with the aid of the supplied IntelliBeam
microphone, allowing you to avoid troublesome listening-based setup and achieving highly accurate sound adjustments
that best match your listening environment. We call these two features “IntelliBeam” generically.
Beam optimization:
This feature optimizes the beam angle so that the parameter best matches your listening environment.
Sound optimization:
This feature optimizes the beam delay, volume, and quality so that the parameters best match your listening environment.

The flow chart of AUTO SETUP

This unit performs a series of checks to optimize the beam angle, delay, volume, and quality. You can choose to optimize
all or part of the parameters.

Notes
Checking the environment of
*1 The beam angle checking procedure is skipped if SOUND

SETUP
your listening room
OPTIMZ only is selected.
*2 The sound optimization procedure is skipped if BEAM
*1 OPTIMZ only is selected.
*3 The subwoofer checking procedure is skipped if BEAM
Beam OPTIMZ only is selected.
Optimizing the beam angle optimization

*2 *3
Checking the subwoofer and Sound
optimizing the beam delay, optimization
frequency, and volume

English

31 En
AUTO SETUP (IntelliBeam)

Installing the IntelliBeam microphone

The supplied IntelliBeam microphone collects and analyzes the sound that this unit produces in your actual listening
environment. Follow the procedure below to connect the IntelliBeam microphone to this unit and make sure that the
IntelliBeam microphone is placed in a proper location and that there are no large obstacles between the IntelliBeam
microphone and the walls in your listening room.

Notes
• After you have completed the AUTO SETUP procedure, be sure to disconnect the IntelliBeam microphone.
• The IntelliBeam microphone is sensitive to heat.
– Keep it away from direct sunlight.
– Do not place it on top of this unit.
• Do not connect the IntelliBeam microphone to an extension cable as doing so may result in an inaccurate sound optimization.
• An error may occur during the AUTO SETUP procedure if the IntelliBeam microphone is not properly placed in your listening room.
To avoid the possibility of an error:
– Do not place the IntelliBeam microphone to the extreme right or left from the center of this unit.
– Do not place the IntelliBeam microphone within 1.8 m (6.0 ft) from the front of this unit.
– Do not place the IntelliBeam microphone more than 1 m (3.3 ft) upper or lower from the center height of this unit.
• Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects
obstruct the path of sound beams. However, any objects that are in contact with the walls will be regarded as a protruding part of the
walls.
• The best possible results are achieved if the IntelliBeam microphone is placed at the same height as your ears would be when you are
seated in your listening position. However, if this is not possible, you can manually fine-tune the sound beam angle and balance the
sound beam output levels using MANUAL SETUP (see page 56) once the AUTO SETUP procedure is completed.
• If a subwoofer with adjustable volume and crossover/high-cut frequency controls is connected to VOLUME CROSSOVER
HIGH CUT
this unit, set the volume between 10 and 12 o’clock as viewed on a conventional clockface and set
the crossover/high-cut frequency to the maximum.

MIN MAX MIN MAX

Subwoofer

1 Press STANDBY/ON to turn off the power of 3 Place the IntelliBeam microphone on a flat
this unit. level surface more than 1.8 m (6.0 ft) from the
STANDBY/ON front of the unit and within 1 m (3.3 ft) upper
or lower from the center height of the unit
or with the IntelliBeam microphone facing
STANDBY/ON
upward at your normal listening position.
Front panel Remote control
Note
Be sure to place the IntelliBeam microphone on an
imaginary center line drawn from this unit.
2 Connect the supplied IntelliBeam
microphone to the INTELLIBEAM MIC jack on y
the front panel. You may want to use the supplied cardboard microphone
stand to affix the IntelliBeam microphone at the same height
as your ears would be when you are seated in your listening
position.

Upper bound
position of the
IntelliBeam microphone
microphone

Within 1 m (3.3 ft)

INTELLIBEAM MIC More than upper or lower
1.8 m (6.0 ft) from the center
height
Cardboard Sofa
microphone stand Lower bound
position of the
microphone

32 En
 AUTO SETUP (IntelliBeam)

Using AUTO SETUP (IntelliBeam)

Once the IntelliBeam microphone is firmly connected to
this unit and properly placed in your listening room,
follow the procedure below to start the AUTO SETUP
procedure.
You can also enter the AUTO SETUP procedure simply by
pressing and holding AUTO SETUP for more than two
seconds. In this case, this unit performs both of the beam
optimization and sound optimization procedures.

Center line
IntelliBeam
microphone

■ Assembling the supplied cardboard

microphone stand INPUT VOLUME STANDBY/ON

You will find three separate parts (one circular part and
two longitudinal parts) of the cardboard microphone stand
originally put together.

SETUP
1 2
STANDBY/ON POWER POWER

AV TV

STB VCR DVD AUX

TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP

5BEAM ST+3BEAM 3BEAM

1 2 3
STEREO MY BEAM MY SUR.

4 5 6
3 4
7 8 9
SUR. DECODE

0 +10

CH LEVEL MENU

TV/AV
ENTER
YSP

1 Disassemble the three parts of the cardboard TEST RETURN

microphone stand originally put together. VOLUME CH TV VOL

2 Insert one of the longitudinal part into the

crevice of the other longitudinal part.

3 Place the circular part on top of the two

combined longitudinal parts.

4 Place the supplied IntelliBeam microphone

English

on top of the circular part.

33 En
AUTO SETUP (IntelliBeam)

Notes 3 Press MENU.

• Make sure that your listening room is as quiet as possible while The SET MENU screen appears on your TV.
this unit is performing the AUTO SETUP procedure.
• To achieve the best results possible, evacuate yourself from
your listening room until the AUTO SETUP procedure is SET MENU
completed so that you may not obstruct the path of sound . ;MEMORY
beams.
MENU ;AUTO SETUP
;MANUAL SETUP
• Be advised that it is normal for loud test tones to be output ;LANGUAGE SETUP
during the AUTO SETUP procedure. [ ]/[ ]:Up/Down

p
• The AUTO SETUP procedure may not be run successfully if [ENTER]:Enter
this unit is installed in one of the rooms described in “Before
installing this unit” on page 13. In such cases, run MANUAL
SETUP (see page 56) to manually adjust the corresponding
parameters. y
• If an error occurs, an error buzzer is played, the AUTO SETUP • The control buttons used for SET MENU are displayed at
procedure stops, and an error message appears on the screen. the bottom of the screen.
See “Error messages for AUTO SETUP” on page 37 for • To return to the previous screen while using SET MENU,
appropriate remedies. press RETURN.
• To exit from the SET MENU screen, press MENU again.
y • You can start the BEAM+SOUND OPTIMZ procedure
• The AUTO SETUP procedure takes about three minutes simply by pressing and holding AUTO SETUP for more
maximum. A chime is played when the AUTO SETUP than two seconds. Steps 4 and 5 are skipped and then the
procedure is run successfully. screen shown in step 5 is displayed on your TV. Start the
• If there are curtains in your listening room, we recommend AUTO SETUP procedure from step 6.
following the procedure below. • You can also perform the following operations in the front
1. Open the curtains to improve sound reflection. panel display.
2. Run BEAM OPTIMZ only.
3. Close the curtains.
4. Run SOUND OPTIMZ only. 4 Press / to select AUTO SETUP and
• You can save the settings optimized by the AUTO SETUP press ENTER.
procedure (see page 38). A set of settings optimized according The following screen appears on your TV.
to the specific conditions of your listening environment can be
recalled later depending on the varying conditions of your
listening environment (see page 39).
ENTER

1 Press STANDBY/ON to turn on the power of

ENTER

this unit.
If a subwoofer is connected to this unit, turn on the
power of the subwoofer.
STANDBY/ON

or ;AUTO SETUP
STANDBY/ON . 1)BEAM+SOUND OPTIMZ
2)BEAM OPTIMZ only
Front panel 3)SOUND OPTIMZ only
Remote control
[ ]/[ ]:Up/Down
p

[ENTER]:Enter

2 Set the operation mode selector to YSP.

TV/AV
YSP

34 En
 AUTO SETUP (IntelliBeam)

5 Press / to select BEAM+SOUND 6 Check the following points once again before
OPTIMZ, BEAM OPTIMZ only, or SOUND starting the AUTO SETUP procedure.
OPTIMZ only and then press ENTER. • Is the IntelliBeam microphone firmly connected to
The following screen appears on your TV. this unit?
• Is the IntelliBeam microphone placed in a proper
location?
ENTER
• Are there any large obstacles in between the
ENTER
IntelliBeam microphone and the walls in your
listening room?

7 Press ENTER to start the AUTO SETUP

procedure.
AUTO SETUP
PREPARATION & CHECK
The following screen appears on your TV and the
AUTO SETUP procedure starts in 10 seconds.
Please connect the MIC.
Please place the MIC at least Leave the room quietly before starting the AUTO
1.8m/6ft away from the YSP SETUP procedure.
unit. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
ENTER

SETUP
BEAM+SOUND OPTIMZ
(Beam optimization and sound optimization)
Use to optimize the beam angle, delay, volume, and
quality so that the parameters best match your listening
environment.
It is recommended that you should select this optimization AUTO SETUP START
feature in the following cases: Will begin in 10sec
• If you make settings for the first time. Please leave the room ← Flashes
• If the unit has been relocated.
• If your listening room has been restructured. **--------
[RETURN]:Cancel
• If the objects in your listening room (furniture, etc.)
have been rearranged.
This menu takes about three minutes.
If an error occurs, an error buzzer is played and an
BEAM OPTIMZ only error message is displayed. See “Error messages for
(Beam optimization only) AUTO SETUP” on page 37 for a complete list of
Use to optimize the beam angle so that the parameter best error messages and their proper remedies. Follow the
matches your listening environment. instructions and perform the AUTO SETUP
This menu takes about one minute. procedure again.
SOUND OPTIMZ only
(Sound optimization only)
Use to optimize the beam delay, volume, and quality so
that the parameters best match your listening environment.
It is recommended that you should select this optimization
feature in the following cases:
• If you have opened or closed the curtains in your
listening room before using this unit.
• If you have manually set the beam angle.
This menu takes about two minutes.

Note
English

You must optimize the beam angle in the BEAM OPTIMZ only
procedure before starting the SOUND OPTIMZ only procedure.

35 En
AUTO SETUP (IntelliBeam)

8 Check that the following screen is displayed 9 Press ENTER to confirm the results or press
on your TV. RETURN to cancel the results.
The results of the AUTO SETUP procedure are The following screen is displayed for two seconds
displayed on your TV. and then disappears from your TV.

Example 1

SHOW RESULT AUTO SETUP COMPLETE

MEASUREMENT COMPLETE ← Flashes ENTER

Please remove the MIC from
the YSP and the listening
position.
BEAM MODE :5 BEAM
SUBWOOFER :NOT APPLICABLE
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.

If “ENVIRONMENT CHECK [FAILED]” is displayed in

step 8, the following screen is displayed after pressing
Example 2
ENTER. In this case, see ERROR E-1 in “Error messages
for AUTO SETUP” on page 37. Press ENTER to exit
AUTO SETUP and then run the procedure again from
SHOW RESULT step 3.
MEASUREMENT COMPLETE ← Flashes
ENVIRONMENT CHECK[FAILED]
BEAM MODE :5 BEAM
SUBWOOFER :YES
[ENTER]:Save set-up. AUTO SETUP COMPLETE
[RETURN]:Do not save set-up. Your YSP unit may not be set
up correctly.
We recommend you try again.
Please press [ENTER] key to
exit.
y
• If “ENVIRONMENT CHECK [FAILED]” is
displayed, we recommend running the AUTO SETUP
procedure again. For details, see step 9.
• If “SUBWOOFER : NOT APPLICABLE” is displayed 10 Disconnect the IntelliBeam microphone from
even though a subwoofer is connected to this unit, the INTELLIBEAM MIC jack on the front
increase the volume level of the subwoofer and run the panel.
AUTO SETUP procedure again.
• Depending on the environment of your listening room,
the beam angle of front left and right, and surround left
and right may be set to the same value even if
“5 BEAM” is displayed as a result.

y
If you want to save and load settings, see “Using the system
memory” on page 38.

36 En
 AUTO SETUP (IntelliBeam)

■ Error messages for AUTO SETUP

Before the AUTO SETUP procedure starts

See
Error message Cause Remedy
page
ERROR E-2 The IntelliBeam microphone is not Connect the IntelliBeam microphone to 32
No MIC detected. Please check connected to this unit. this unit.
MIC connection and re-try.

While the AUTO SETUP procedure is in progress

If one of the errors listed below except E-1 is displayed, press RETURN. In case you have started the AUTO SETUP
procedure by pressing AUTO SETUP in step 3, run the procedure again from step 3 after the screen disappears. In case
you have started the AUTO SETUP procedure by pressing MENU in step 3, run the procedure again from step 4 after the
screen in step 3 is displayed. Run MANUAL SETUP if the problem is difficult to be saved.

See
Error message Cause Remedy
page
ERROR E-1 There is too much unwanted noise in Make sure that your listening room is as —
Please test in quieter environment. your listening room. quiet as possible. You may want to
choose certain hours during the day
when there is not much noise coming
from outside.

SETUP
ERROR E-2 The IntelliBeam microphone was Make sure that the IntelliBeam 32
No MIC detected. Please check disconnected while the AUTO SETUP microphone is firmly connected to this
MIC connection and re-try. procedure was in progress. unit.

ERROR E-3 Some other operations were performed Do not perform any other operations —
Unexpected control is detected. on this unit while the AUTO SETUP while the AUTO SETUP procedure is in
Please re-try. procedure was in progress. progress.

ERROR E-4 The IntelliBeam microphone is not Make sure that the IntelliBeam 32
Please check MIC position. MIC placed in front of this unit. microphone is installed in front of this
should be set in front of YSP. unit.

ERROR E-5 The IntelliBeam microphone is not Make sure that the IntelliBeam 32
Please check MIC position. MIC placed in the right distance from this microphone is installed more than 1.8 m
should be set above 1.8m/6.0ft. unit. (6.0 ft) from the front of this unit and
within 1 m (3.3 ft) from the center height
of this unit.

ERROR E-6 The IntelliBeam microphone cannot Make sure that the IntelliBeam 32
Volume level is lower than collect the sound produced by this unit microphone is firmly connected to this
expected. Please check MIC because the sound output level is too low. unit and placed in a proper location. If
position/connection and re-try. the problem persists, contact the nearest
authorized Yamaha service center for
assistance.

ERROR E-7 An internal system error occurred. Repeat the AUTO SETUP procedure. —
Unexpected error happened.
Please re-try.
English

37 En
USING THE SYSTEM MEMORY

Using the system memory

Convenient usage of the system 3 Press / to select MEMORY and press
memory ENTER.
The following screen appears on your TV.
You can save the current settings adjusted in SET MENU
in the system memory of this unit. It is handy to save
certain settings according to the varying conditions of
your listening environment. For example, if there are ENTER
ENTER
curtains in the path of sound beams, the effectiveness of
the sound beams will vary depending on whether the
curtains are open or closed.

When the curtains are When the curtains are

open closed
;MEMORY
. 1)LOAD
2)SAVE

p
[ ]/[ ]:Up/Down

p
[ENTER]:Enter

4 Press / to select SAVE and press

Saving settings ENTER.
The following screen appears on your TV.
1 Set the operation mode selector to YSP.

TV/AV
ENTER
ENTER
YSP

2 Press MENU.
The SET MENU screen appears on your TV.

SET MENU 2)MEMORY SAVE

. ;MEMORY
MENU ;AUTO SETUP . MEMORY1
;MANUAL SETUP MEMORY2
;LANGUAGE SETUP MEMORY3

[ ]/[ ]:Up/Down
p

[ ]/[ ]:Select
p

[ENTER]:Enter
[ENTER]:Enter

y
• The control buttons used for SET MENU are displayed at
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN.
• To exit from the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.

38 En
 Using the system memory

5 Press / to select MEMORY1, Loading settings

MEMORY2, or MEMORY3 and press ENTER.
You can recall the settings saved in “Saving settings” on
The following screen appears on your TV.
page 38 according to the varying conditions of your
listening environment.

ENTER
ENTER
1 Set the operation mode selector to YSP.

TV/AV
YSP

2)MEMORY SAVE 2 Press MENU.

The SET MENU screen appears on your TV.
MEMORY1 Save Now ?

Push [ENTER] to Save

SET MENU
. ;MEMORY
MENU ;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
[ ]/[ ]:Up/Down

SETUP
[ENTER]:Enter
6 Press ENTER again.
The new parameters are saved as MEMORY1,
MEMORY2, or MEMORY3. Once the parameters
are saved, the display returns to the SET MENU y
screen. • The control buttons used for SET MENU are displayed at
the bottom of the screen.
• To return to the previous screen while using SET MENU,
2)MEMORY SAVE press RETURN.
• To exit from the SET MENU screen, press MENU once
MEMORY1 Saving more.
ENTER • You can also perform the following operations in the front
panel display.

3 Press / to select MEMORY and press

ENTER.
The following screen appears on your TV.

SET MENU
. ;MEMORY ENTER
;AUTO SETUP ENTER
;MANUAL SETUP
;LANGUAGE SETUP
[ ]/[ ]:Up/Down
p

[ENTER]:Enter

7 Press MENU to exit.

;MEMORY
. 1)LOAD
The SET MENU screen disappears from your TV. 2)SAVE
p

MENU [ ]/[ ]:Up/Down

p

[ENTER]:Enter
English

39 En
Using the system memory

4 Press / to select LOAD and press 6 Press ENTER again.

ENTER. The new parameters saved as MEMORY1,
The following screen appears on your TV. MEMORY2, or MEMORY3 are loaded. Once the
parameters are loaded, the display returns to the SET
MENU screen.

ENTER
ENTER
1)MEMORY LOAD
MEMORY1 Loading
ENTER

1)MEMORY LOAD
. MEMORY1
MEMORY2
MEMORY3

[ ]/[ ]:Select SET MENU

p

[ENTER]:Enter
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
[ ]/[ ]:Up/Down

p
[ENTER]:Enter
5 Press / to select MEMORY1,
MEMORY2, or MEMORY3 and press ENTER.
The following screen appears on your TV.

7 Press MENU to exit.

The SET MENU screen disappears from your TV.

ENTER MENU
ENTER

1)MEMORY LOAD
MEMORY1 Load Now ?

Push [ENTER] to Load

40 En
 PLAYBACK

Playback
■ Front panel operations
Selecting the input source Press INPUT on the front panel repeatedly to
You can play back sound from the components connected toggle between TV/STB, VCR, DVD, and AUX.
to this unit simply by pressing INPUT on the front panel The name of the corresponding input source and the type
repeatedly or pressing one of the input selector buttons of current input mode are displayed in the front panel
(STB, VCR, DVD, AUX, or TV) on the remote control. display.
The name of the selected input source and the type of
corresponding input mode appear in the front panel ■ Remote control operations
display. y
In addition to controlling this unit, you can also operate other AV
components if you set up the remote control with the appropriate
remote control codes and set the operation mode selector to TV/
AV to change the control area (see page 79).

Press TV to play back a TV program.

TV
INPUT VOLUME STANDBY/ON

STB VCR

INPUT1
DVD
TV
INPUT2
AUX

MACRO
XTV/STBXAUTO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP Name of the selected Type of the selected
input source input mode
5BEAM ST+3BEAM 3BEAM

OPERATION
1 2 3

BASIC
STEREO MY BEAM MY SUR.

4 5 6 Press STB to play back a satellite broadcast.

7 8 9
SUR. DECODE
STB
0 +10

CH LEVEL MENU

TV/AV
ENTER
YSP
TEST RETURN

XTV/STBXAUTO

Press DVD to play back a DVD.

DVD

XXDVDXXXAUTO
English

41 En
Playback

Press VCR to play back a component connected

to the VCR input jack on the rear panel of this 2 Switch to the video input on your TV using
unit. the remote control supplied with the TV and
display the DVD menu screen.
VCR
Note

If necessary, turn down the volume of your TV until no

sound is heard.

3 Press DVD to select DVD as the input source.

XVCR
DVD

Press AUX to play back a component connected

to the AUX jack on the rear panel of this unit.
4 Play back DVD on your DVD player using the
AUX supplied remote control.
Audio signals from your DVD player are output from
this unit.
y
• You can use the supplied demonstration DVD to check the
digital signals being input at the DVD player with the digital
XXAUXXXXAUTO connection (optical/coaxial). The MULTI indicator lights up
when this unit detects the 5.1-channel signal input at the optical/
coaxial jack. If the PCM indicator lights up, confirm the
settings of the digital output, bitstream output, and/or DTS
Playing back sources output of the DVD player.
• If the output volume is too low, increase the volume of this unit
Once an input source is selected (see page 41), you can to around 45.
play back the selected input source. • If you have set the appropriate remote control codes for your
TV and DVD player, you can use the remote control supplied
Note with this unit to operate these components. For details on how
to set remote control codes, see page 79.
This section uses a DVD player as an example of the playback
source.
y
For details on your TV and DVD player, refer to the respective
owner’s manual.

1 Turn on the power of your DVD player.

42 En
 Playback

■ Muting the sound

Adjusting the volume VOLUME CH TV VOL

MUTE TV INPUT TV MUTE

CODE SET

1 Press MUTE to mute the sound.

INPUT VOLUME STANDBY/ON “AUDIO MUTE ON” appears in the front panel
display, and the volume level indicator flashes.
MUTE

VOLUME CH TV VOL

MUTE TV INPUT TV MUTE

AUDIOXMUTEXON
Press VOLUME +/– to increase or decrease the Flashes
volume level.
The numeric value of the volume level appears in the front
panel display. XXDVDXXX5BEAM
Control range: MIN (minimum), 01 to 99,
MAX (maximum)
2 Press MUTE again (or press VOLUME +/–) to
VOLUME resume the sound output.
“AUDIO MUTE OFF” appears temporarily in the

OPERATION
front panel display (or the numeric value of the

BASIC
or
current volume level appears if you press VOLUME
VOLUME + +/–), and the volume level indicator lights up.
VOLUME
Front panel Remote control MUTE
or

XXVOLUMEXX30XX Lights up

Notes AUDIOXMUTEXOFF
• The volume level of all input sources (including multi-channel
as well as stereo sources) changes at the same time.
• One volume level increases or decreases each time you press Note
VOLUME +/–. The sound output of all input sources (including multi-channel as
• You can continuously increase or decrease the volume level if well as stereo sources) is muted at the same time.
you press and hold VOLUME +/–.
y
You can select whether the sound output is to be muted
completely or by 20 dB when you press MUTE (see page 62).
English

43 En
ENJOYING SURROUND SOUND

Enjoying surround sound

You can enjoy multi-channel surround sound by changing the beam mode using the beam mode buttons on the remote
control. Select 5 Beam, Stereo plus 3 Beam, 3 Beam, or My Surround for multi-channel playback.
Notes
• When ANGLE TO WALL OR CORNER is set in MANUAL SETUP (see page 58), 5 Beam and 3 Beam cannot be selected.
• To enjoy 5 Beam, Stereo plus 3 Beam, or 3 Beam as the beam mode, you must perform AUTO SETUP or MANUAL SETUP so that
the parameters best match your listening environment.

5 Beam
AUTO
VOL MODE SETUP INPUTMODE SLEEP
Outputs sound beams from the front left, front right,
5BEAM ST+3BEAM 3BEAM

1 2 3
center, surround left, and surround right channels. This
STEREO MY BEAM MY SUR. mode is ideal for enjoying surround sound effects to the
4 5 6 fullest when you watch DVDs recorded in a multi-channel
7 8 9
format or play back 2-channel sources in a multi-channel
SUR. DECODE format.
0 +10

CH LEVEL MENU
Press 5BEAM to select 5 Beam.
5BEAM

ENTER
TV/AV 1
YSP
TEST RETURN

1 Set the operation mode selector to YSP.

TV/AV
YSP

Notes
2 Press one of the beam mode buttons
• To achieve the best surround sound effect, make sure that there
(5BEAM, ST+3BEAM, 3BEAM, or MY SUR.) to are no obstacles placed in the path of sound beams in that the
select the desired beam mode for 5.1- objects may prevent the sound beams from rebounding directly
channel play back. off the walls in your listening room.
• The front left and right sound beams are output toward the walls
5BEAM ST+3BEAM 3BEAM in your listening room.
1 2 3 • “SP Pos. Corner!” appears in the front panel display if
INSTALLED POSITION is set to ANGLE TO WALL OR
MY SUR.
CORNER (see page 58).
6

44 En
 Enjoying surround sound

y
Stereo plus 3 Beam You can achieve a more realistic surround effect if you adjust
settings for IMAGE LOCATION in BEAM MENU (see page 61).
Outputs normal sound from the front left and right
channels and sound beams from the center and surround Notes
left and right channels. This mode is ideal for watching • When you play back multi-channel sources, surround left and
live recordings on a DVD. Vocals and instrumental sounds right signals are mixed down and output from the front left and
can be heard close to the center of the listening position right channels.
while sound reflections from the venue itself can be heard • The front left and right sound beams are output toward the walls
on your right and left, giving you the feeling that you are in your listening room.
sitting right in front of the stage. • “SP Pos. Corner!” appears in the front panel display if
INSTALLED POSITION is set to ANGLE TO WALL OR
Press ST+3BEAM to select Stereo plus 3 Beam. CORNER (see page 58).
ST+3BEAM
2
My Surround
This mode enables surround system in a small listening
area which may not fulfill the listening room conditions
for other beam modes (see “Before installing this unit” on
page 13). Use this beam mode when you want to enjoy
surround sound near this unit, or when the other beam
modes are unavailable.
Press MY SUR. to select My Surround.
MY SUR.
Note 6
The front left and right sound beams are output directly toward
the listening position.

OPERATION
3 Beam

BASIC
Outputs sound beams from the front left and right and
center channels. This mode is ideal for enjoying movies
with the whole family. Because the listening position area
is widened, you can enjoy excellent quality surround
sound over a wider area. In addition, you can use this
mode when the listening position is close to the backside Notes
of the wall, and the surround left and right sound beams • Beam mode settings such as beam angles and distances are
cannot be reflected off the wall. ineffective in this mode.
• For the full effect of My Surround, your listening position must
Press 3BEAM to select 3 Beam. face toward the front of this unit.
3BEAM
3
English

45 En
Enjoying surround sound

■ Decoder indicators ■ Surround modes and recommended

Depending on the input source and the selected surround sources
mode, the decoder indicators in the front panel display
light up as follows: Recommended
Surround mode
source

Status Indicator Cinema Movies

DTS Neo:6
Music Music

When PCM signals are being input Dolby Pro Logic – All sources
PCM
Movie Movies
When DTS digital signals are being Dolby Pro Logic II Music Music
input or DTS Neo:6 is selected as Game Games
the surround mode
Notes
When Dolby Digital signals are • When you select an input source (see page 41), the surround
being input DIGITAL mode used for the previously selected input source is
automatically selected.
• If the power of this unit is turned off and on again, the surround
When Dolby Pro Logic is selected
PL mode used for the previously selected input source before the
as the surround mode
power was turned off is automatically selected.
• If the surround modes are not available, “Prohibit” appears in
When Dolby Pro Logic II is selected the front panel display when you press SUR. DECODE.
as the surround mode PL • The surround modes are available:
– when the beam mode is set to a setting other than the stereo
y playback (see page 50), My Beam (see page 51), and My
• You can select an input mode (AUTO, DTS, or ANALOG) by Surround (see page 45).
pressing INPUTMODE repeatedly (see page 70). – when 2-channel signals are being input.
• Discs encoded in DTS-ES, Dolby Digital 5.1 EX, Dolby Digital
EX, or Dolby Digital Surround EX will be played back in DTS
or Dolby Digital.

46 En
 Enjoying surround sound

Enjoying 2-channel sources 2 Press SUR. DECODE repeatedly (or press

in surround sound SUR. DECODE and then press / ) to
switch between surround modes.
This unit can decode 2-channel sources for 5.1-channel Choices: Neo:6 Cinema, Neo:6 Music, PRO LOGIC,
playback so that you can enjoy a variety of surround sound PLII Movie, PLII Music, PLII Game
effects by switching the surround mode. Default setting: Neo:6 Cinema
y
The beam mode must be set to 5 Beam, Stereo plus 3 Beam, or 3 SUR. DECODE

Beam (see page 44).

5BEAM ST+3BEAM 3BEAM

1 2 3 or
STEREO MY BEAM MY SUR.

4 5 6

7 8 9 SUR. DECODE
SUR. DECODE ENTER
0 +10

CH LEVEL MENU

TV/AV
ENTER
YSP
TEST RETURN

Neo:6 Cinema

1 Set the operation mode selector to YSP. Neo:6 Music

TV/AV PRO LOGIC

OPERATION
YSP

BASIC
PLII Movie

PLII Music

PLII Game

English

47 En
Enjoying surround sound

Enjoying TV in surround sound 4 If you hear sound from your TV speakers,

reduce the volume level of your TV until you
You can enjoy analog audio signals output from your TV
can no longer hear any audio being output.
in real surround sound.
To reduce the TV volume level, use the remote
y control supplied with your TV.
Before performing the steps below, set the volume of this unit to
30. If necessary, adjust the volume level in step 4 below.
5 Press VOLUME +/– to adjust the volume
level.
TV
INPUT1 INPUT2 MACRO
TV VOLUME
AUTO
VOL MODE SETUP INPUTMODE SLEEP

5BEAM ST+3BEAM 3BEAM

1 2 3
STEREO MY BEAM MY SUR.

4 5 6

7 8 9
SUR. DECODE

0 +10

CH LEVEL MENU
6 Press SUR. DECODE repeatedly (or press
SUR. DECODE and then press / ) to
TV/AV
ENTER
YSP
switch between surround modes.
TEST RETURN
Signals input from 2-channel sources are played back
VOLUME CH TV VOL
in multi-channels.
For more information on surround modes, see
page 46.

SUR. DECODE

or
1 Select the TV channel you want to watch.
To select a TV channel, use the remote control
supplied with your TV. SUR. DECODE

ENTER

2 Set the operation mode selector to YSP.

TV/AV
YSP

3 Press TV.
This unit outputs audio signals from your TV.

TV

48 En
 Enjoying surround sound

■ When Dolby Pro Logic II Music is

Adjusting surround mode selected
parameters PANORAMA
You can configure the parameters for Dolby Pro Logic II Gives the front left and right channel sound a
Music and DTS Neo:6 Music to fine-tune the surround wraparound effect, distributed throughout the entire
sound effect. surround sound field to give you an expansive feeling.
Choices: ON/OFF
Default setting: OFF
7 8 9
SUR. DECODE
DIMENSION
0 +10

CH LEVEL MENU
Adjusts the difference in volume between the front
and surround channels to the desired volume balance.
TV/AV
Control range: –3 (toward the surround direction) to
ENTER
YSP +3 (toward the front direction)
TEST RETURN
Default setting: STD (standard)
C. WIDTH
Distributes the center channel sound to the left and
right. If 0 is selected, the center channel sound is
output only from the center channel.
1 Repeat steps 1 and 2 in “Enjoying 2-channel
Control range: 0 to 7
sources in surround sound” on page 47 and
Default setting: 3
select PL II Music or Neo:6 Music.
■ When DTS Neo:6 Music is selected
2 Press / to select the parameter. C. IMAGE
Adjusts the center image from three channels (front
left and right and center) to varying degrees.
Control range: 0.0 (wider) to 1.0 (toward the center)

OPERATION
ENTER
Default setting: 0.3

BASIC
3 Press / to configure the selected
parameter.

ENTER
English

49 En
ENJOYING STEREO SOUND

Enjoying stereo sound

You can enjoy 2-channel stereo playback as the beam modes by pressing STEREO on the remote control. Sounds are
output from the front right and left channels. This is ideal for playing back hi-fi sources, such as CDs, and can be used to
replace your TV speakers.

Notes
• When you play back Dolby Digital audio signals in the stereo playback, the dynamic range becomes compressed. If the volume level
decreases to the extreme, use other beam modes except My Beam.
• When the stereo playback is selected as the beam mode, the surround modes (see page 46) become ineffective.

1 2 3
STEREO MY BEAM MY SUR.

4 5 6

7 8 9
SUR. DECODE

0 +10

CH LEVEL MENU

TV/AV
ENTER
YSP
TEST RETURN

1 Set the operation mode selector to YSP. Note

When you play back multi-channel sources, all signals except
TV/AV those from the front left and right channels are mixed down and
YSP output from the front left and right channels. No audio is output
from the center and surround channels.

2 Press STEREO to select the stereo playback

as the beam mode.
“STEREO” appears in the front panel display.
STEREO
4

XSTEREOXMODE

50 En
 PLAYING BACK SOUND CLEARLY (MY BEAM)

Playing back sound clearly (My Beam)

You can improve listenability in a noisy environment by changing the beam mode to My Beam, which outputs sound
beams directly toward the listening position in a single channel. In addition, My Beam is also ideal when you do not want
the sound beams to be reflected on the walls in your listening room or when you do not want to disturb other people
while enjoying music or movies at night.

My Beam
microphone

STANDBY/ON POWER POWER

AV TV

SLEEP

5BEAM ST+3BEAM 3BEAM

1 2 3
STEREO MY BEAM MY SUR.

4 5 6

7 8 9
SUR. DECODE

0 +10

CH LEVEL MENU

TV/AV
ENTER
YSP
TEST RETURN

Note

OPERATION
If My Beam is selected as the beam mode, the surround modes (see page 46) and TruBass (see page 63) become ineffective. In addition,
no audio is output from the subwoofer connected to this unit.

BASIC
Using auto-adjust function Notes
• If an error occurs, an error buzzer is played and “MY BEAM
The My Beam microphone on the remote control collects
ERROR” is displayed in the front panel display.
the test tones from this unit so that the beam angle can be
• An error may occur if the listening room is noisy. Make sure
automatically adjusted. that the listening room is as quiet as possible while the test
tones are being output.
1 Set the operation mode selector to YSP. • Do not shake or move the remote control while the test tones are
being output.
• Do not cover the My Beam microphone on the remote control
TV/AV
while the test tones are being output.
YSP
• The batteries in the remote control may be weak if the remote
control does not function properly. In this case, replace all the
batteries and then try the procedure again.
2 Press and hold MY BEAM for more than two • When the input signal with 64 kHz, 88.2kHz, or 96 kHz of
seconds. sampling frequency is being played back, the beam angle
A test tone is output twice from this unit. Keep cannot be automatically adjusted.
pointing the remote control toward this unit while the
test tones are being output so that the My Beam
microphone can collect the test tones.
Control range: L50° to R50°
Operation guarantee range: 6 m (20 ft), L30° to R30°
English

MY BEAM
5

51 En
Playing back sound clearly (My Beam)

Using manual-adjust function

You can adjust the beam angle manually while playing
back an input source. This function is also ideal if the
listening position is out of the operation guarantee range
of the auto-adjust function.

1 Set the operation mode selector to YSP.

TV/AV
YSP

2 Press MY BEAM.
“MY BEAM” is displayed in the front panel display.

MY BEAM
5

3 Press / while “MY BEAM” is displayed to

adjust the beam angle.
Control range: L90° to R90°
• Press repeatedly to increase the horizontal angle
on the left side.
• Press repeatedly to increase the horizontal angle
on the right side.

ENTER

ANGLE 0

4 Press MY BEAM again to complete the beam

angle adjustment.

52 En
 USING THE VOLUME MODE (NIGHT LISTENING ENHANCER/TV VOLUME EQUAL MODE)

Using the volume mode

(Night listening enhancer/TV volume equal mode)
The night listening enhancers are designed to improve listenability at lower volumes or at night. In addition, you can limit
the volume level of the TV so that it will not vary suddenly to a great extent whenever the contents being broadcast
change (i.e. due to commercials, etc.).
The EQUAL indicator lights up in the front panel
AUTO
VOL MODE SETUP INPUTMODE SLEEP display when “TV EQUAL VOLUME” is selected.
5BEAM ST+3BEAM 3BEAM

1 2 3
STEREO MY BEAM MY SUR.

4 5 6

7 8 9
SUR. DECODE
Lights up
0 +10

CH LEVEL MENU
• Select NIGHT:CINEMA when watching films to
reduce the dynamic range of film soundtracks and
TV/AV
to make dialog easier to hear at lower volumes.
ENTER
YSP • Select NIGHT:MUSIC when listening to music
TEST RETURN
sources to preserve ease-of-listening for all sounds.
• Select TV EQUAL VOLUME when watching TV
programs.
• Select OFF to turn off the volume mode.

1 Set the operation mode selector to YSP.

3 Press / to adjust the effect level of
TV/AV
compression while NIGHT:CINEMA,
YSP
NIGHT:MUSIC, or TV EQUAL VOLUME is

OPERATION
displayed.

BASIC
2 Press VOL MODE repeatedly to select
NIGHT:CINEMA, NIGHT:MUSIC, TV EQUAL
VOLUME, or OFF. ENTER

VOL MODE

Effect.Lvl:MIN
NIGHT:CINEMA
Effect.Lvl:MID
NIGHT:MUSIC
Effect.Lvl:MAX
TV EQUAL VOL • Select Effect.Lvl:MIN for minimum compression.
• Select Effect.Lvl:MID for standard compression.
OFF • Select Effect.Lvl:MAX for maximum
compression.
The NIGHT indicator lights up in the front panel
display when “NIGHT:CINEMA” or Notes
“NIGHT:MUSIC” is selected.
• The volume mode settings are canceled if you press
STANDBY/ON or disconnect the AC power supply cable from
the AC wall outlet.
English

• The volume mode settings become ineffective when My

Surround is selected as the beam mode (see page 45).
Lights up

53 En
USING THE SLEEP TIMER

Using the sleep timer

Use this feature to automatically set this unit to the standby mode after a specified period of time. The sleep timer is
useful if you are going to sleep after a certain amount of time while this unit is still playing back a source.
Each time you press SLEEP, the front panel display
INPUT1
TV
INPUT2 MACRO changes as shown below.
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
SLEEP
5BEAM ST+3BEAM 3BEAM

1 2 3
STEREO MY BEAM MY SUR.

4 5 6

7 8 9

0 +10
SUR. DECODE
SLEEP 120min
CH LEVEL MENU

SLEEP 90min
TV/AV
ENTER

TEST
YSP
RETURN
SLEEP 60min

SLEEP 30min

SLEEP OFF
1 Set the operation mode selector to YSP.
3 Wait for a few seconds without operating this
TV/AV
unit to confirm the setting for the sleep timer.
YSP
The SLEEP indicator lights up in the front panel
display, indicating that the sleep timer is activated.

2 Press SLEEP repeatedly to set the interval

for the sleep timer.
Choices: 120min, 90min, 60min, 30min, OFF
The SLEEP indicator flashes in the front panel
Lights up
display while switching the interval for the sleep
timer.

SLEEP

Flashes

54 En
 Using the sleep timer

■ Canceling the sleep timer

1 Set the operation mode selector to YSP.

TV/AV
YSP

2 Press SLEEP repeatedly until “SLEEP OFF”

appears in the front panel display.
SLEEP

XSLEEPXXOFF

3 Wait for a few seconds without operating this

unit to confirm the setting for the sleep timer.
The SLEEP indicator disappears from the front panel
display, indicating that the sleep timer is deactivated.

Disappears

OPERATION
BASIC
Note
The previous setting for the sleep timer before you deactivate it is
stored in the system memory.
y
The sleep timer setting can also be deactivated if you press
STANDBY/ON to set this unit to the standby mode or unplug the
AC power supply cable from the AC outlet.

English

55 En
MANUAL SETUP

MANUAL SETUP
To achieve the best quality surround sound, you can use MANUAL SETUP to fine-tune the listening environment
parameters, as well as to make advanced settings for sound signals, sound beams, digital input, and the OSD. Change the
initial settings (indicated in bold under each parameter) to reflect the needs of your own listening environment.
y
• You can save the settings optimized by the AUTO SETUP procedure (see page 38). A set of settings optimized according to the
specific conditions of your listening environment can be recalled later depending on the varying conditions of your listening
environment (see page 39).
• Most of the parameters in SOUND MENU and BEAM MENU are automatically set when you run AUTO SETUP (see page 31). Use
SOUND MENU and BEAM MENU to make additional adjustments.
• BEAM MENU allows you to make settings for the surround sound effects normally available in the speaker settings menu.
• Make settings for the parameters in BEAM MENU first before making settings for the parameters in SOUND MENU, INPUT MENU,
and DISPLAY MENU.
SOUND MENU
Use to manually adjust the various parameters related to the sound output.
Item Features Page
TONE CONTROL Adjusts the output level of high-frequency or low-frequency sound. 62
SUBWOOFER SET Adjusts the various subwoofer settings. 62
MUTE LEVEL Adjusts the muting level. 62
AUDIO DELAY Adjusts the audio delay. 63
DD/DTS Dynamic Range Adjusts the dynamic range of Dolby Digital or DTS signals. 63
TruBass Selects the bass sound enhancer. 63

BEAM MENU
Use to manually adjust the various parameters related to the sound beam output.
Item Features Page
SETTING PARAMETERS Adjusts the listening room and listening position settings. 58
BEAM ADJUSTMENT Adjusts the various sound beam settings. 59
IMAGE LOCATION Adjusts the sound position of the front left and right channels. 61

INPUT MENU
Use to manually adjust the various parameters related to the audio and video input.
Item Features Page
INPUT MODE Selects the initial input of the source. 64
INPUT TRIM Adjusts the input level of the source. 64
INPUT RENAME Renames the displayed input source. 65

DISPLAY MENU
Use to manually adjust the various parameters related to the display.
Item Features Page
F.DISPLAY SET Adjusts the front panel display settings. 66
OSD SET Adjusts the OSD settings. 66
UNIT SET Changes the display unit of measurement. 66

56 En
 MANUAL SETUP

Using MANUAL SETUP 3 Press / to select MANUAL SETUP and

press ENTER.
Use the remote control to access and adjust each
The following screen appears on your TV.
parameter.

7 8 9
SUR. DECODE
ENTER
0 +10 ENTER

CH LEVEL MENU

TV/AV
ENTER
YSP
TEST RETURN

VOLUME CH TV VOL

;MANUAL SETUP
. 1)SOUND MENU
2)BEAM MENU
3)INPUT MENU
4)DISPLAY MENU
[ ]/[ ]:Up/Down

p
[ENTER]:Enter
y
You can adjust the SET MENU parameters while the unit is
reproducing sound.

1 Set the operation mode selector to YSP. 4 Press / to select a sub menu and press
ENTER.
TV/AV
YSP

ENTER
ENTER

2 Press MENU.
The SET MENU screen appears on your TV.

SET MENU 5 Press / / / and ENTER to configure

. ;MEMORY each parameter.
MENU ;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
[ ]/[ ]:Up/Down
p

OPERATION
ADVANCED
[ENTER]:Enter
ENTER

y
• The control buttons used for SET MENU are displayed at
the bottom of the screen.
• To return to the previous screen while using SET MENU, 6 Press MENU to exit.
press RETURN.
• To exit from the SET MENU screen, press MENU once
The OSD disappears from your TV screen.
more.
• You can also perform the following operations in the front MENU

panel display.
English

57 En
MANUAL SETUP

ANGLE TO WALL
BEAM MENU FLAT TO WALL OR CORNER

Use to manually adjust the various parameters related to

the sound beam output.
SET MENU → MANUAL SETUP → BEAM MENU

2)BEAM MENU
. A)SETTING PARAMETERS
B)BEAM ADJUSTMENT
C)IMAGE LOCATION
• Select FLAT TO WALL if this unit is installed in
[ ]/[ ]:Up/Down parallel with the wall in your listening room. Adjust the
p

[ENTER]:Enter
width and length of your listening room as well as the
distance of the listening position from this unit and the
distance of the center of this unit from the left wall.
y
You can adjust the sound beam output level of each channel in Listening position
from the left wall
“Adjusting the audio balance” (see page 67).

■ SETTING PARAMETERS
(Setting parameters)
Listening position
Use to set the position of this unit in your listening room from the unit
and the distance of this unit from the listening position. Room length
When you make settings for each parameter, other related
parameters are automatically adjusted to best match your
listening environment.
Room width
Note
If you make adjustments in SETTING PARAMETERS, the beam Choices for the room width and length:
optimization settings made in the AUTO SETUP procedure will 2.0 m to 12.0 m (6.5 ft to 40.0 ft)
be lost. If you want to keep the beam optimization settings made Choices for the listening position from this unit:
in the AUTO SETUP and make further adjustments, adjust 1.8 m to 9.0 m (6.0 ft to 30.0 ft)
settings in BEAM ADJUSTMENT first (see page 59). Choices for the listening position from the left wall:
0.6 m to 11.4 m (2.0 ft to 38.0 ft)

A)SETTING PARAMETERS 1/3

A)SETTING PARAMETERS 2/3
. INSTALLED POSITION
;;;;;;;FLAT TO WALL |
p p Room width and -------[ 5.4m ]-
[ ]/[ ]:Up/Down [ ]/[ ]:Sel length |
p

[ENTER]:Return 4.9m
|
p p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
p

[ENTER]:Return

INSTALLED POSITION
(Installed position of this unit)
Use to adjust the installed position of this unit.
Choices: FLAT TO WALL (Parallel to wall installation),
ANGLE TO WALL OR CORNER A)SETTING PARAMETERS 3/3
(Corner installation) Listening position
--------|
from the unit and 2.7m [ 2.5m ]
the left wall |

p p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
p

[ENTER]:Return

58 En
 MANUAL SETUP

• Select ANGLE TO WALL OR CORNER if this unit is ■ BEAM ADJUSTMENT (Beam adjustment)
installed in the corner of your listening room. Adjust Use to manually adjust the various sound beam settings.
the width and length of your listening room as well as We recommend that you select 5 Beam as the beam mode
the distance of the listening position from this unit. before adjusting these parameters (see page 44).
Listening position
from the unit
Notes
• When INSTALLED POSITION is adjusted in MANUAL
SETUP (see page 58), the factory default value is automatically
set for this parameter except Center in FOCAL LENGTH (see
page 60).
• Depending on the beam mode settings (see pages 44 and 50),
Room width some channel positions may not be available for selection. In
this case, “– –” is displayed. When using Stereo plus 3 Beam as
the beam mode, set the surround left and right signals to be
output from the front left and right channels.

Room length

Choices for the room width and length:

B)BEAM ADJUSTMENT
. a)HORIZONTAL ANGLE
2.0 m to 12.0 m (6.5 ft to 40.0 ft) b)BEAM TRAVEL LENGTH
c)FOCAL LENGTH
Choices for the listening position from this unit: d)TREBLE GAIN
1.8 m to 9.0 m (6.0 ft to 30.0 ft) [ ]/[ ]:Up/Down

p
[ENTER]:Enter

A)SETTING PARAMETERS 2/3

----- 5.4m ---
|
HORIZONTAL ANGLE (Horizontal angle)
Room width and
[ 5.4m ] Use to adjust the horizontal angle of sound beams for each
length |
| channel. By adjusting the horizontal angle of the sound
p p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel beams, you can optimize the sound beam paths. A test
p

[ENTER]:Return
tone is automatically output.

( ) (+)
(+) ( )

A)SETTING PARAMETERS 3/3

Listening \
[ 2.5m ]

OPERATION
position from the

ADVANCED
\
unit
p p Choices: L90° to R90°
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
p

[ENTER]:Return Adjust toward L (left) to move the direction of the output

to the left and adjust toward R (right) to move it to the
right.

Note
When you set the INSTALLED POSITION parameter in
a)HORIZONTAL ANGLE5 beam
1/5
MANUAL SETUP (see page 58), the parameters newly set for Front L L90 R90
the width and length of your listening room are automatically set L65deg
*
as the factory default value.
0(deg)
p p
p

[ ]/[ ]:Up/Down [ ]/[ ]:Sel

p

[ENTER]:Return
English

59 En
MANUAL SETUP

BEAM TRAVEL LENGTH (Beam travel length) FOCAL LENGTH (Focal length)
A certain amount of delay must be applied to the sound Use to set the distance from the front of this unit to the
from each channel so that all sounds can arrive at the focal point of output for each channel to achieve an
listening position at the same time. This menu sets the expansive feeling for each channel.
distance that sound beams travel after being output and The focal points except for the center channel should be
reflected off the wall until they arrive at the listening set near the reflection points on the walls. The shorter the
position and adjusts the delay applied to the respective distance, the larger the expansion.
channel.
The lines in the illustration below indicate the distance.
focal length

focal point

sweet spot

Choices: 0.3 m to 24.0 m (1.0 ft to 80.0 ft)

• Front L adjusts the distance the front left channel Front left channel Center channel
sound beams travel.
• Front R adjusts the distance the front right channel
sound beams travel.
• Center adjusts the distance the center channel sound
beams travel.
• Surround L adjusts the distance the surround left
channel sound beams travel.
• Surround R adjusts the distance the surround right Choices: –1.0 m to +13.0 m (–3.5 ft to +43.5 ft)
channel sound beams travel. Adjust toward – (minus) to move the focus outward and
adjust toward + (plus) to move the focus toward the
normal position.
b)BEAM TRAVEL LENGTH
5 beam
• Front L adjusts the focal length for the front left sound
beams.
. Front L;;;;;;;6.0m
Front R;;;;;;;6.0m • Front R adjusts the focal length for the front right
Center;;;;;;;;2.5m
Surround L;;;;9.1m sound beams.
Surround R;;;;9.1m
p p • Center adjusts the focal length for the center sound
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
p

[ENTER]:Return beams. Initial setting: –0.3 m (–1.0 ft)

• Surround L adjusts the focal length for the surround
left sound beams.
• Surround R adjusts the focal length for the surround
y right sound beams.
We recommend that you use the setting optimized by AUTO
SETUP (see page 31). Adjust this parameter only when you y
changed HORIZONTAL ANGLE (see page 59). We recommend that you use the initial setting (–0.3 m
(or –1.0 ft)) for the center channel.

c)FOCAL LENGTH
5 beam
. Front L;;;;;;+1.5m
Front R;;;;;;+1.5m
Center;;;;;;;-0.3m
Surround L;;;+2.3m
Surround R;;;+2.3m
p p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
p

[ENTER]:Return

60 En
 MANUAL SETUP

TREBLE GAIN (Treble gain) ■ IMAGE LOCATION (Image location)

Use to adjust the high-frequency output level of each Use to adjust the direction from which the front left and
channel. right channel sound is heard so that each sound can be
heard closer to the center channel.
y
If the reflection points of the front left and right or surround left Use this feature to redirect audio signals if the sound
and right sound beams are on curtain or other acoustically coming from the front left and right channels seems
absorbent surfaces, you can achieve more effective surround unnatural, such as when your listening position is not the
sound by increasing the treble level for those sound beams. center of your listening room.
You can only adjust this parameter when 3 Beam or 5
Beam is selected as the beam mode (see page 44).
Choices: ON, OFF
Setting range: 0% to 95%
Initial setting: 0%

C)IMAGE LOCATION
. OFF )ON
L C R
Choices: –12.0 dB to +12.0 dB

p
LEFT;;;;;;;;;;;0%
Initial setting: 0 dB RIGHT;;;;;;;;;;0%
• Front L adjusts the high-frequency output level of the p p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel

p
front left channel. [ENTER]:Return

• Front R adjusts the high-frequency output level of the

front right channel.
• Center adjusts the high-frequency output level of the LEFT (Left)
center channel. Adjusts audio signals toward the left.
• Surround L adjusts the high-frequency output level The higher the percentage, the louder the output from the
of the surround left channel. center.
• Surround R adjusts the high-frequency output level
of the surround right channel. With the front left
Without adjustment channel adjusted

d)TREBLE GAIN
- +
. Front L;;;;;;;;0dB ------
Front R;;;;;;;;0dB ------
Center;;;;;;;;;0dB ------
Surround L;;;;;0dB ------
Surround R;;;;;0dB ------
p p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
p

[ENTER]:Return

OPERATION
ADVANCED
RIGHT (Right)
Adjusts audio signals toward the right.
The higher the percentage, the louder the output from the
center.

With the front right

Without adjustment channel adjusted
English

61 En
MANUAL SETUP

BASS OUT (Bass out)

SOUND MENU Low-frequency (bass) signals can be directed to the
subwoofer and/or the front left and right channels. This
Use to manually adjust the various parameters related to setting also determines the routing of LFE (low-frequency
the sound output. effect) signals found in Dolby Digital or DTS sources.
SET MENU → MANUAL SETUP → SOUND MENU Choices: SWFR (Subwoofer), FRONT
• Select SWFR if you connect a subwoofer. LFE and
low-frequency signals from other channels are directed
1)SOUND MENU to the subwoofer.
. A)TONE CONTROL
B)SUBWOOFER SET • Select FRONT if you do not use a subwoofer. LFE and
C)MUTE LEVEL
D)AUDIO DELAY low-frequency signals from other channels are directed
E)DD/DTS Dynamic Range
F)TruBass to the front left and right channels.
[ ]/[ ]:Up/Down
p

[ENTER]:Enter
CROSS OVER (Crossover)
When BASS OUT is set to SWFR, you can use this
feature to select a crossover (cutoff) frequency for all low-
■ TONE CONTROL (Tone control) frequency signals. All frequencies below the selected
You can adjust the tonal quality of sound beams. frequency will be sent to the subwoofer position.
Choices: 100Hz, 120Hz, 150Hz
LFE LEVEL (Low-frequency effect level)
A)TONE CONTROL- + Select to adjust the output level of the LFE (low-frequency
. TREBLE;;;;;0dB ------
- + effect) channel according to the capacity of your
BASS;;;;;;;0dB ------ subwoofer. The LFE channel carries low-frequency
p p special effects which are only added to certain scenes.
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
p

[ENTER]:Return This setting is effective only when this unit decodes Dolby
Digital or DTS signals.
Choices: –20 to 0 dB

TREBLE (Treble) DISTANCE (Distance)

Use to adjust the high-frequency response. Select to adjust the distance of the subwoofer from the
Choices: –12 dB to +12 dB listening position.
Initial setting: 0 dB Choices: 0.3 to 15.0 m (1.0 ft to 50.0 ft)
Initial setting: 3.0 m (10.0 ft)
BASS (Bass)
Use to adjust the low-frequency response. ■ MUTE LEVEL (Muting level)
Choices: –12 dB to +12 dB Use to adjust how much the mute function reduces the
Initial setting: 0 dB volume level.
Choices: MUTE, –20 dB
■ SUBWOOFER SET (Subwoofer settings) • Select MUTE to completely halt all sound output.
Use to manually adjust the various subwoofer • Select –20 dB to reduce the current volume level by
settings. 20 dB.

B)SUBWOOFER SET C)MUTE LEVEL

. BASS OUT;;;;;FRONT pMUTE -20dB
CROSS OVER;;;100Hz
LFE LEVEL;;;;;;0dB
DISTANCE;;;;;;3.0m p
p p p
[ ]/[ ]:Select
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
p

[ENTER]:Return
[ENTER]:Return

62 En
 MANUAL SETUP

■ AUDIO DELAY (Audio delay) ■ TruBass

Use to delay the sound output and synchronize it with the Use to turn on or off the bass sound enhancer. The SRS
video image. This may be necessary when using certain TruBass technology improves bass even without a
LCD monitors or projectors. subwoofer and provides deeper, richer bass in the presence
Choices: 0 to 160 msec of a subwoofer.
Choices: OFF, ON

D)AUDIO DELAY
AUDIO DELAY;;;;;0msec F)TruBass
p p OFF pON
[ ]/[ ]:Select
[ENTER]:Return
p p
[ ]/[ ]:Select
[ENTER]:Return

■ DD/DTS Dynamic Range

(Dynamic range of Dolby Digital and
DTS signals) Note
Use to select the amount of dynamic range compression. TruBass is not available when My Beam (see page 51) or My
This setting is effective only when the unit is decoding Surround (see page 45) is selected as the beam mode.
Dolby Digital and DTS signals. Dynamic range is the
difference between the smallest sound that can be heard
above the noise of the equipment and the biggest sound
that can be heard without distortion.
Choices: MIN (minimum), STD (standard),
MAX (maximum)

E)DD/DTS Dynamic Range

MIN STD pMAX
p p
[ ]/[ ]:Select
[ENTER]:Return

Select to adjust the dynamic range compression.

• Select MIN for listening to sources at low volume

OPERATION
ADVANCED
levels.
• Select STD for general use.
• Select MAX for feature films. English

63 En
MANUAL SETUP

■ INPUT TRIM (Input trim)

INPUT MENU Use to adjust the input level of the input source.
Use to manually adjust the various parameters related to
the audio and video input.
SET MENU → MANUAL SETUP → INPUT MENU B)INPUT TRIM
. TV/STB ANALOG;;;-3.0dB
DIGITAL;;-3.0dB
VCR ANALOG;;;-3.0dB
3)INPUT MENU DVD
AUX
DIGITAL;;-3.0dB
DIGITAL;;-3.0dB
p p
. A)INPUT MODE [ ]/[ ]:Up/Down [ ]/[ ]:Sel

p
B)INPUT TRIM [ENTER]:Return
C)INPUT RENAME

• Select TV/STB ANALOG to adjust the level of audio

p

[ ]/[ ]:Up/Down
p

[ENTER]:Enter and video signals input at the TV/STB AUDIO INPUT

jacks of this unit.
Control range: –6.0 dB to 0.0 dB
■ INPUT MODE (Input mode) Initial setting: –3.0 dB
Use to designate the input mode for the input sources • Select TV/STB DIGITAL to adjust the level of audio
connected to the DIGITAL INPUT jacks when you turn on and video signals input at the TV/STB OPTICAL
the power of this unit. For information on the types of DIGITAL INPUT jack of this unit.
audio signals that can be output by this unit, see “Selecting Control range: –6.0 dB to 0.0 dB
the input mode” on page 70. Initial setting: –3.0 dB
Choices: AUTO, LAST • Select VCR ANALOG to adjust the level of audio and
video signals input at the VCR AUDIO INPUT jacks
of this unit.
A)INPUT MODE Control range: –6.0 dB to 0.0 dB
pAUTO LAST Initial setting: –3.0 dB
• Select DVD DIGITAL to adjust the level of audio and
p p video signals input at the DVD COAXIAL DIGITAL
[ ]/[ ]:Select
[ENTER]:Return INPUT jack of this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select AUTO to set this unit to automatically detect the • Select AUX DIGITAL to adjust the level of audio and
type of input signals and select the appropriate input video signals input at the AUX OPTICAL DIGITAL
mode. INPUT jack of this unit.
• Select LAST to set this unit to automatically select the Control range: –6.0 dB to 0.0 dB
last input mode used for that input source. If the type of Initial setting: –3.0 dB
input signals is different from the setting, no sounds
will be produced.

64 En
 MANUAL SETUP

■ INPUT RENAME (Input rename)

Use to change the name of the input source in the OSD
and the front panel display. Press an input selector button
(e.g., DVD) to select the component you want to change
the name for and perform the following procedure.

C)INPUT RENAME
DVD -> DVD

p p
[ ]/[ ]:Position
[ ]/[ ]:Character
p

[ENTER]:Return

1 Press / to place the _ (underscore) under

the space or the character you want to edit.
The _ (underscore) flashes.

ENTER

2 Press / to select the desired character.

• You can use up to 8 characters for each input.
• Press to change the character in the following
order or press to go in the reverse order:
A to Z, a space, 0 to 9, a space, a to z, a space, #, *,
+, etc.

ENTER

OPERATION
ADVANCED
3 Repeat steps 1 to 2 to rename each input.

4 Press ENTER to exit.

The new names are registered, and the display returns
to the previous screen.

ENTER
English

65 En
MANUAL SETUP

■ OSD SET (OSD settings)

DISPLAY MENU Use to adjust the display position and to set the display
time of the OSD.
Use to manually adjust the various parameters related to
the display.
SET MENU → MANUAL SETUP → DISPLAY MENU B)OSD SET
OSD SHIFT;;;;;;;;;;0
4)DISPLAY MENU p p
. A)F.DISPLAY SET [ ]/[ ]:Select
B)OSD SET [ENTER]:Return
C)UNIT SET

[ ]/[ ]:Up/Down
p

[ENTER]:Enter
OSD SHIFT (OSD shift)
Use to adjust the vertical position of the OSD. Adjust
toward the – (minus) direction to raise the position of the
■ F.DISPLAY SET OSD, and adjust toward the + (plus) direction to lower it.
(Front panel display settings) Choices: –5 to +5
Use to adjust the brightness and display settings of the Initial setting: 0
front panel display.
■ UNIT SET (Unit settings)
Use this to change the display unit of measurement.
A)F.DISPLAY SET Choices: METERS, FEET
. STANDARD DIMMER;;;;;OFF
AUTO DIMMER
;;;;;;;;;;;;;OFF
C)UNIT SET
p METERS FEET
p p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
p

[ENTER]:Return
p p
[ ]/[ ]:Select
[ENTER]:Return

STANDARD DIMMER (Standard dimmer)

Use to adjust the brightness of the front panel display
when you operate this unit by using the control buttons on • Select METERS to enter distances in meters.
the front panel or on the remote control. • Select FEET to enter distances in feet.
Choices: –2, –1, OFF
Note
AUTO DIMMER (Auto dimmer)
If you change this setting, the adjusted sound beam settings may
If no operation is performed for a specified period of time,
change.
the front panel display dims. Use to adjust the brightness
of the front panel display in this case.
Choices: OFF (the same brightness as the STANDARD
DIMMER setting), –1 to –3 (based on the
STANDARD DIMMER setting), DISPLAY OFF

66 En
 Adjusting the audio balance

Adjusting the audio balance

You can adjust the sound beam output level of each channel by using the test tone or the audio output being played back
in each beam mode to achieve a more true-to-life surround sound experience.

Using the test tone 3 Press / to select the channel you want
to adjust.
You can use the test tone feature to output a test tone from
The front panel display changes as follows:
each channel to manually balance the channel levels.
Use this to set the channel levels so that the volume level
of each channel is identical when heard from your TEST FRONT L
listening position.
ENTER
TEST CENTER
CH LEVEL MENU

TEST FRONT R
TV/AV
ENTER
YSP
TEST RETURN TEST SUR.R

TEST SUR.L

1 Set the operation mode selector to YSP. TEST SUBWOOFER

TV/AV Note
YSP
“TEST SUBWOOFER” is only available when a subwoofer
is connected to this unit and SWFR is selected for BASS
OUT in SOUND MENU (see page 62).
2 Press TEST.
“TEST LEFT” appears in the front panel display and 4 Press / to adjust the channel volume.
a test tone is output from the front left channel.

TEST

ENTER

OPERATION
ADVANCED
Control range: –10.0 dB to +10.0 dB

TESTXLEFT
English

67 En
Adjusting the audio balance

5 Press TEST when you have completed all 1 Set the operation mode selector to YSP.
your adjustments.
TV/AV

TEST YSP

2 Press CH LEVEL repeatedly (or press

CH LEVEL and / ) to select the channel
Notes you want to adjust.
• All channel levels cannot be adjusted when the stereo playback The front panel display changes as follows.
(see page 50), My Beam (see page 51), or My Surround (see
page 45) is selected as the beam mode. CH LEVEL
• “FRONT L/R” cannot be adjusted when Stereo plus 3 Beam is
selected as the beam mode (see page 45).
• “FRONT L/R” are automatically adjusted depending on the
settings of the other channels when Stereo plus 3 Beam or or
stereo playback is selected as the beam mode (see pages 45 and
50).
CH LEVEL
y ENTER
If the level of a particular channel cannot be adjusted, “– –dB”
appears in the front panel display.

Using the audio output being

played back
FRONT L +1.0dB
You can also manually adjust the channel levels while
playing back an input source such as a DVD. CENTER -2.5dB

FRONT R +1.0dB
CH LEVEL MENU

TV/AV
SUR.R +2.0dB
ENTER
YSP
TEST RETURN
SUR.L +2.0dB

SWFR --dB

Note
“SWFR” is available only when a subwoofer is connected to
this unit and SWFR is selected for BASS OUT in SOUND
MENU (see page 62).

68 En
 Adjusting the audio balance

3 Press / to adjust the channel volume.

ENTER

Control range: –10.0 dB to +10.0 dB

4 Wait for a few seconds without operating this

unit when you have completed your
adjustment.

Notes
• All channel levels cannot be adjusted when the stereo playback
(see page 50), or My Surround (see page 45) is selected as the
beam mode.
• “FRONT L/R” cannot be adjusted when Stereo plus 3 Beam is
selected as the beam mode (see page 41).
• Only CENTER can be adjusted when My Beam is selected as
the beam mode (see page 51).
• “FRONT L/R” are automatically adjusted depending on the
settings of the other channels when Stereo plus 3 Beam or
stereo playback is selected as the beam mode (see pages 45 and
50).
y
If the level of a particular channel cannot be adjusted, “– –dB”
appears in the front panel display.

OPERATION
ADVANCED
English

69 En
Selecting the input mode

Selecting the input mode

You can select the type of audio input signals of the selected input source according to your preference or the conditions
of the input source. This function is available for TV/STB, DVD, and AUX.
y
We recommend setting the input mode to AUTO in most cases.

3 Press INPUTMODE repeatedly to toggle

AV TV between input modes.

INPUTMODE

STB VCR DVD AUX

TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP

5BEAM ST+3BEAM 3BEAM

1 2 3 DVD AUTO TV/STB AUTO

STEREO MY BEAM MY SUR.

4 5 6 DVD DTS TV/STB DTS

7 8 9
SUR. DECODE
When DVD is selected TV/STB ANALOG
+10
as the input source
0
When TV or STB is selected
CH LEVEL MENU
as the input source

ENTER
TV/AV AUX AUTO
YSP
TEST RETURN
AUX DTS

When AUX is selected as

the input source

1 Set the operation mode selector to YSP.

Note
TV/AV
ANALOG is not available as the input mode of DVD and
YSP
AUX.

• AUTO
2 Press one of the input selector buttons to Automatically selects audio input signals in the following
select the desired input source. priority order:
1) Dolby Digital or DTS
STB VCR DVD AUX
2) PCM
3) Analog
TV y
Use this input mode in most cases.

• DTS
Selects only digital signals encoded in DTS.
Compared to AUTO, this input mode provides greater
stability while playing back CDs or LDs encoded in DTS.
• ANALOG
Selects only analog signals.
Even when both digital and analog signals are input
simultaneously, only analog signals are selected.

y
You can adjust the default input mode to be selected when the
power of this unit is turned on by adjusting INPUT MODE in
INPUT MENU (see page 64).

70 En
 Adjusting the system parameters

Adjusting the system parameters

This unit has additional menus that are displayed in the front panel display. These menus offer additional operations to
adjust and customize the way this unit operates.

Note
When “F.PANEL KEY” is set to “F.PANEL: OFF” (see page 76), STANDBY/ON on the front panel is ineffective. Use STANDBY/ON
on the remote control instead to adjust the system parameters.

Using the system parameters 2 Press and hold INPUT on the front panel and
press STANDBY/ON on the remote control to
Follow the procedure below to enter the system
turn on the power of this unit.
parameters.
“MEMORY PROTECT” is displayed in the front
panel display.

STANDBY/ON

INPUT

INPUT VOLUME STANDBY/ON

MEMORYXPROTECT

STANDBY/ON POWER POWER

CH LEVEL MENU 3 Release INPUT on the front panel.
AV TV

TV/AV
ENTER
YSP
TEST RETURN
STB VCR DVD AUX INPUT
TV
INPUT1 INPUT2 MACRO
TV

1 Press STANDBY/ON on the remote control to

turn off the power of this unit.

OPERATION
ADVANCED
STANDBY/ON
English

71 En
Adjusting the system parameters

Setting the MEMORY PROTECT 4 Press / to switch between “PROTECT:

ON” and “PROTECT: OFF”.
You can protect the settings you saved in the system
memory of this unit from being accidentally erased or
unwantedly changed.
ENTER

1 Repeat steps 1 to 3 in “Using the system

parameters” on page 71.

2 Set the operation mode selector to YSP.

TV/AV
YSP
XPROTECT:XON

3 Confirm that “MEMORY PROTECT” is

displayed in the front panel display and
press ENTER.
XPROTECT:XOFF
• Select PROTECT: ON to activate the protection
MEMORYXPROTECT feature.
• Select PROTECT: OFF to deactivate the protection
feature.

5 Press STANDBY/ON on the remote control to

set this unit to the standby mode.
ENTER STANDBY/ON

The new setting will be activated when you turn on

the power of this unit next time.

72 En
 Adjusting the system parameters

Setting the MAX VOLUME 5 Press / to adjust the maximum volume

level.
You can set the maximum volume level so that this unit
will not output sound beyond the limited volume level.

1 Repeat steps 1 to 3 in “Using the system ENTER

parameters” on page 71.

2 Set the operation mode selector to YSP.

“ Control range: MAX, 99 to 01, MIN
Control step: 1
TV/AV
YSP
6 Press STANDBY/ON on the remote control to
set this unit to the standby mode.
3 Press / so that “MAX VOLUME SET” is
STANDBY/ON
displayed in the front panel display.

The new setting for the maximum volume level will

ENTER
be activated when you turn on the power of this unit
next time.

Setting the TURN ON VOLUME

You can set the initial volume level when the power of this
unit is turned on.

MAXXVOLUMEXSET 1 Repeat steps 1 to 3 in “Using the system

parameters” on page 71.

4 Press ENTER.
2 Set the operation mode selector to YSP.

TV/AV
ENTER YSP

OPERATION
ADVANCED
English

73 En
Adjusting the system parameters

3 Press / so that “TURN ON VOLUME” is Setting the DEMO MODE

displayed in the front panel display.
You can test the sound beam output from this unit to
experience the sound beam.

ENTER
1 Repeat steps 1 to 3 in “Using the system
parameters” on page 71.

2 Set the operation mode selector to YSP.

TV/AV
YSP

TURNXONXVOLUME
3 Press / so that “DEMO MODE” is
displayed in the front panel display.
4 Press ENTER.

ENTER
ENTER

5 Press / to adjust the initial volume level.

DEMOXMODE
ENTER

Control range: MAX, 99 to 01, OFF

4 Press ENTER.
Control step: 1

6 Press STANDBY/ON on the remote control to ENTER

set this unit to the standby mode.

STANDBY/ON

The new setting for the maximum volume level will

be activated when you turn on the power of this unit
next time.

74 En
 Adjusting the system parameters

5 Press / to switch between “DEMO: ON” Setting the PANEL INP. KEY
and “DEMO: OFF”.
You can disable the INPUT on the front panel when you
adjust the system parameters.

ENTER 1 Repeat steps 1 to 3 in “Using the system

parameters” on page 71.

2 Set the operation mode selector to YSP.

TV/AV
YSP
XDEMO:XXON
3 Press / so that “PANEL INP. KEY” is
displayed in the front panel display.

XDEMO:XXOFF ENTER

• Select DEMO: ON to activate the demo mode.

• Select DEMO: OFF to deactivate the demo mode.

6 Press STANDBY/ON on the remote control to

set this unit to the standby mode.

STANDBY/ON PANELXINP.XKEY

4 Press ENTER.
The new setting will be activated when you turn on
the power of this unit next time.
Press ENTER while playing back sources to test the
sound beam. ENTER

OPERATION
The sound beam being output shuttles between left

ADVANCED
and right. Press ENTER again to stop shuttling.
English

75 En
Adjusting the system parameters

5 Press / to switch between “P.INPUT: ON” Disabling the front panel keys
and “P.INPUT: OFF”.
You can disable the front panel keys except when you
adjust the system parameters.

ENTER
1 Repeat steps 1 to 3 in “Using the system
parameters” on page 71.

2 Set the operation mode selector to YSP.

TV/AV
YSP
XP.INPUT:XON
3 Press / so that “F.PANEL KEY” is
displayed in the front panel display.

XP.INPUT:XOFF ENTER

• Select P.INPUT: ON to enable the INPUT key on

the front panel.
• Select P.INPUT: OFF to disable the INPUT key on
the front panel. “F.PANEL KEY” is automatically
set to “ON”.

6 Press STANDBY/ON on the remote control to F.PANELXKEY

set this unit to the standby mode.

STANDBY/ON 4 Press ENTER.

The new setting will be activated when you turn on ENTER

the power of this unit next time.

76 En
 Adjusting the system parameters

5 Press / to switch between “F.PANEL: Setting the FACTORY PRESET

ON” and “F.PANEL: OFF”.
You can reset all of the parameters of this unit to the
factory presets. This procedure completely resets ALL the
parameters in SET MENU.
ENTER
Note
After performing the following procedure you must run AUTO
SETUP again to match your surround sound environment.

1 Repeat steps 1 to 3 in “Using the system

parameters” on page 71.

XF.PANEL:XON
2 Set the operation mode selector to YSP.

TV/AV
YSP

XF.PANEL:XOFF 3 Press / so that “FACTORY PRESET” is

displayed in the front panel display.
• Select F.PANEL: ON to enable the front panel
keys.
• Select F.PANEL: OFF to disable the front panel
keys. “P.INPUT” is automatically set to “ON”. ENTER

6 Press STANDBY/ON on the remote control to

set this unit to the standby mode.

STANDBY/ON

FACTORYXPRESET
The new setting will be activated when you turn on
the power of this unit next time.
4 Press ENTER.

OPERATION
ADVANCED
ENTER
English

77 En
Adjusting the system parameters

5 Press / to switch between “PRESET:

RESET” and “PRESET: CANCEL”.

ENTER

XPRESET:XRESET

XPRESET:CANCEL
• Select PRESET: RESET to reset all of the current
settings.
• Select PRESET: CANCEL to cancel the resetting
procedure.

6 Press STANDBY/ON on the remote control to

set this unit to the standby mode.

STANDBY/ON

The new setting will be activated when you turn on

the power of this unit next time.

78 En
 Remote control features

Remote control features

In addition to controlling this unit, the remote control can also operate other AV components made by Yamaha and other
manufacturers. To control other components, you must set up the remote control with the appropriate remote control
codes and set the operation mode selector to TV/AV to change the control area.

Note
Depending on the external AV component you are using, you may not be able to operate the component with the remote control, even if
a remote control code is set. In this case, operate the component using the supplied remote control.

Setting remote control codes 2 Press the numeric buttons to enter the
remote control code while holding down
You can control other components by setting the
CODE SET.
appropriate remote control codes. Codes can be set up for
each input area (STB, VCR, DVD, AUX, and TV). Setting example: Yamaha DVD input area
For a complete list of available remote control codes, refer MY SUR.

to “List of remote control codes” at the end of this manual. 6

TV MUTE
Transmission indicator While holding
down, press 9
CODE SET
AV TV

STB VCR DVD AUX

TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP

5BEAM ST+3BEAM 3BEAM

3 Refer to “Controlling other components” on
1 2 3 page 80 to operate the external component
STEREO MY BEAM MY SUR. using the remote control.
4 5 6
If the external component functions correctly the
7 8 9 remote control code setup is successful.
+10
SUR. DECODE
If the external component does not function correctly,
0
the remote control code may be incorrect. Confirm
that the remote control code is correct. See “List of
MUTE TV INPUT TV MUTE
remote control codes” at the end of this manual and
CODE SET
start over from step 1.

OPERATION
ADVANCED
Note
1 Press and hold CODE SET and press one of
If the manufacturer of your component has more than one code,
the input selector buttons to select the input try each of them until you find the correct one.
source you want to set a remote control code
for.
The transmission indicator flashes twice and remains If the remote control is without batteries for more than
lit. two minutes, or if exhausted batteries remain in the
Proceed to step 2 while holding down CODE SET. remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
STB VCR DVD AUX batteries and reset the remote control codes.
TV MUTE
While holding When changing the batteries, be careful not to press
down, press TV any of the buttons on the remote control. Doing so will
CODE SET
clear the contents of the memory.
English

79 En
Remote control features

Controlling other components

■ Operating your TV 1 Numeric buttons
Selects a TV channel for playback.
Set the operation mode selector to TV/AV, and
press TV to select TV as the input source. 2 CH +/–
The control area of the remote control changes to the TV Switches between the available TV channels.
operation mode.
3 TV INPUT
Switches the input source for your TV.
TV/AV
TV
YSP 4 TV POWER
Turns on or off the power of your TV.

STANDBY/ON POWER POWER

5 TV INPUT1/2
AV TV 4 Selects the input source of your TV.
6 TV VOL +/–
Adjusts the audio output level of your TV.
STB VCR DVD
TV
AUX
5
INPUT1 INPUT2 MACRO
TV 7 TV MUTE
AUTO
VOL MODE SETUP INPUTMODE SLEEP
Temporarily mutes audio output from your TV.
5BEAM ST+3BEAM 3BEAM

1 2 3
STEREO MY BEAM MY SUR.

4 5 6
1
7 8 9
SUR. DECODE

0 +10

CH LEVEL MENU

TV/AV
ENTER
YSP
TEST RETURN

VOLUME CH TV VOL

2 6

MUTE TV INPUT TV MUTE

7
3 CODE SET

80 En
 Remote control features

■ Operating your DVD player/recorder ■ Operating your STB

(CATV/Satellite tuner)
Set the operation mode selector to TV/AV and
press DVD to select DVD as the input source. Set the operation mode selector to TV/AV and
The control area of the remote control changes to the DVD press STB to select STB as the input source.
operation mode. The control area of the remote control changes to the STB
operation mode.
TV/AV
DVD
YSP
TV/AV
STB
YSP

STANDBY/ON POWER POWER

AV TV

4 STANDBY/ON POWER POWER

AV TV

STB VCR DVD AUX

3
TV
INPUT1 INPUT2 MACRO
TV
STB VCR DVD AUX
AUTO
VOL MODE SETUP INPUTMODE SLEEP TV
INPUT1 INPUT2 MACRO
TV
5BEAM ST+3BEAM 3BEAM AUTO
VOL MODE SETUP INPUTMODE SLEEP
1 2 3
STEREO MY BEAM MY SUR. 5BEAM ST+3BEAM 3BEAM

1 4 5 6 1 2 3
STEREO MY BEAM MY SUR.
7 8 9 4 5 6
SUR. DECODE 1
0 +10 7 8 9
CH LEVEL MENU SUR. DECODE

5 0 +10

CH LEVEL MENU
TV/AV
ENTER

2
YSP
TEST RETURN
TV/AV
6 ENTER
YSP
VOLUME CH TV VOL TEST RETURN

VOLUME CH TV VOL

MUTE TV INPUT TV MUTE

2
CODE SET
MUTE TV INPUT TV MUTE

CODE SET

OPERATION
ADVANCED
1 Numeric buttons
Enter numeric digits.
1 Numeric buttons
Enter numeric digits. 2 CH +/–
Switches between the available STB channels.
2 Cursor buttons / / / , ENTER
3 AV POWER
Use to select DVD menu items.
Turns on or off the power of your STB.
3 Operation buttons for DVD players
Operate your DVD player/recorder, such as play and stop.
4 AV POWER
Turns on or off the power of your DVD player/recorder.
5 MENU
Displays the DVD menu.
6 RETURN
English

Use to return to the previous DVD menu screen or exit

from the DVD menu.

81 En
Remote control features

■ Operating your VCR

Set the operation mode selector to TV/AV and
press VCR to select VCR as the input source.
The control area of the remote control changes to the VCR
operation mode.

TV/AV
VCR
YSP

STANDBY/ON POWER POWER

AV TV

STB VCR DVD AUX

TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP

5BEAM ST+3BEAM 3BEAM

1 2 3
STEREO MY BEAM MY SUR.

4 5 6
1
7 8 9
SUR. DECODE

0 +10

CH LEVEL MENU

TV/AV
ENTER
YSP
TEST RETURN

VOLUME CH TV VOL

MUTE TV INPUT TV MUTE

CODE SET

1 Numeric buttons
Enter numeric digits.
2 CH +/–
Switches between the available VCR channels.
3 Operation buttons for VCR
Operate your VCR, such as play and stop.
4 AV POWER
Turns on or off the power of your VCR.

82 En
 Remote control features

■ Setting macros for the TV with the

Using the TV macro tuning capability
The TV macro feature makes it possible to perform a
series of operations with the press of a single button. For 1 Press and hold CODE SET and press one of
example, when you want to play a DVD, you would the input selector buttons to select the input
normally turn on the component, select DVD as the input source you want to set macros for.
source, and press the play button to start playback. The TV Proceed to step 2 while holding down CODE SET.
macro feature lets you perform all of these operations
simply by pressing the DVD macro button.
TV MUTE
While holding
Notes STB VCR DVD AUX
down, press
CODE SET
• Be sure to set up a remote control code for your TV before
setting macros.
• The ways to set macros differ if your TV does not have the
tuning capability.
• If you press any control buttons on the remote control other than 2 Press MACRO while holding down CODE
the ones used to set macros while setting macros, the setting SET.
procedure is automatically canceled.
• If it takes more than 10 seconds in steps 2 and 3, the setting
procedure is automatically canceled. In this case, repeat from TV MUTE MACRO
While holding
step 1. down, press
CODE SET
STANDBY/ON POWER POWER

AV TV

3 Press CH +/– or the numeric buttons to select

the TV channel.
STB VCR DVD AUX

INPUT1
TV
INPUT2 MACRO Check that the TV screen changes to the tuner screen.
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
CH 5BEAM ST+3BEAM 3BEAM

5BEAM ST+3BEAM 3BEAM 1 2 3

1 2 3 STEREO MY BEAM MY SUR.

STEREO MY BEAM MY SUR.

or 4 5 6
4 5 6

7 8 9
7 8 9
SUR. DECODE

0 +10 0 +10

CH LEVEL MENU

4 Press TV INPUT repeatedly until the screen

OPERATION
ADVANCED
TV/AV
ENTER
YSP changes to the display of the input source
TEST RETURN
selected in step 1.
VOLUME CH TV VOL

TV INPUT

MUTE TV INPUT TV MUTE

CODE SET

5 Press ENTER to confirm the macro setting.

ENTER
English

83 En
Remote control features

■ Setting macros for the TV without the ■ Operating macros

tuning capability
Press and hold one of the input selector buttons
1 Press and hold CODE SET and press one of for approximately two seconds to select the input
the input selector buttons to select the input source you want to operate macros for.
source you want to set macros for. The TV input changes at the same time the input mode
Proceed to step 2 while holding down CODE SET. changes.

TV MUTE
While holding STB VCR DVD AUX
STB VCR DVD AUX
down, press
CODE SET

■ Canceling the macros

2 Press MACRO while holding down CODE
SET. 1 Press and hold CODE SET and press one of
the input selector buttons to select the input
TV MUTE MACRO
While holding source you want to cancel the macros for.
down, press
Proceed to step 2 while holding down CODE SET.
CODE SET

TV MUTE
While holding
3 Press INPUT1. down, press STB VCR DVD AUX
Check that the TV screen changes to the input 1 CODE SET
screen.

INPUT1
2 Press MACRO while holding down CODE
SET.

TV MUTE MACRO
While holding
4 Press TV INPUT repeatedly until the screen down, press
changes to the display of the input source CODE SET
selected in step 1.

TV INPUT 3 Press ENTER to cancel the macros.

ENTER

5 Press ENTER to confirm the setting.

ENTER

84 En
 Troubleshooting

Troubleshooting
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, set this unit to the standby mode, disconnect the AC power supply cable, and
contact the nearest authorized Yamaha dealer or service center.

■ General

See
Problem Cause Remedy
page
This unit fails to turn on The AC power supply cable is not firmly Connect the AC power supply cable firmly 25
when STANDBY/ON is connected to the AC wall outlet. to the AC wall outlet.
pressed, or enters the
standby mode soon after the This unit has been exposed to a strong Set this unit to the standby mode, disconnect —
power has been turned on. external electric shock (such as lightning the AC power supply cable, plug it back in
and strong static electricity). after 30 seconds, and use it normally.

This unit suddenly enters the The internal temperature becomes too high Wait for about one hour for this unit to cool —
standby mode. and the overheat protection circuitry has down and turn it back on.
been activated.

The sleep timer has turned the unit off. Turn on the power and play back the source —
again.

No sound. Incorrect input or output cable connections. Connect the cables properly. If the problem 16
persists, the cables may be defective.

No appropriate input source has been Select an appropriate input source with 41
selected. INPUT or the input selector buttons.

The volume is turned down. Turn up the volume. 43

The sound is muted. Press MUTE or VOLUME +/– to resume 43
audio output and adjust the volume level.

The signals this unit cannot reproduce (such Play a source whose signals can be —
as PCM signals with more than 96 kHz of reproduced by this unit.
sampling frequency) are being received
from the source component. Change the system settings of the source —
component.

The sound suddenly goes The sleep timer has turned this unit off. Turn on the power and play back the source —
off. again.

The sound is muted. Press MUTE or VOLUME +/– to resume 43

audio output and adjust the volume level.

No sound from the effect You are playing back the source or program Press one of the beam mode buttons on the 44
channels. in the stereo playback or My Beam mode. remote control to select a multi-channel
playback mode and play back the source or
program once more.

No sound from the center The output level of the center channel is set Raise the level of the center channel. 67
channel. to minimum.
INFORMATION

No sound from the surround The output level of the surround channels is Raise the output level of the surround 67
ADDITIONAL

channels. set to minimum. channels.

English

85 En
Troubleshooting

See
Problem Cause Remedy
page
No sound from the BASS OUT in SUBWOOFER SET is set to Select SWFR. 62
subwoofer. FRONT.

The source does not contain low bass

signals.

Distorted or too little bass CROSS OVER in SUBWOOFER SET is set Set CROSS OVER correctly.
62
sound. incorrectly.

One of the night listening enhancers is Turn off the night listening enhancers.
53
currently selected.

Too much bass sound. TruBass is currently turned on. Turn off TruBass. 63
The volume level of the subwoofer is too Turn down the volume level of the
—
high. subwoofer.

Surround sound effects are The listening room is not a regular shape. Install this unit in a square or rectangular —
insubstantial. shaped room.

There is no wall in the path of the sound Try placing a flat object, such as a board, in —
beam. the path of the sound beam.

Dolby Digital or DTS sources The connected component is not set to Make an appropriate setting following the —
cannot be played back. output Dolby Digital or DTS digital signals. operating instructions for your component.
(Dolby Digital or DTS
indicator does not light up in The input mode is set to ANALOG. Set the input mode to AUTO. 70
the front panel display.)

There is noise interference The protection circuitry was in operation Turn down the volume level. 43
when a subwoofer is not because a source with strong bass elements
connected to this unit. was played back. Select SWFR for BASS OUT. 62
Connect a subwoofer and adjust settings for 62
SUBWOOFER SET.

Low-frequency sounds are CROSS OVER in SUBWOOFER SET is set Set CROSS OVER correctly. 62
distorted. incorrectly.

On-screen display does not The OSD video pin cable is not connected Connect the cable properly. 18
appear. properly.

This unit does not operate The internal microcomputer has been frozen Disconnect the AC power supply cable from —
properly. by an external electric shock (such as the outlet and plug it in again after about 30
lightning or excessive static electricity) or seconds.
by a power supply with low voltage.

There is noise interference This unit is too close to the digital or high- Move this unit farther away from such —
from digital or high- frequency equipment. equipment.
frequency equipment.

This unit does not output The original source includes surround Disable the surround effect settings of this —
effect sounds properly. effects. unit.

My Beam auto-adjust The listening room is too noisy. Keep the listening room as quiet as possible. —
function does not work.
Try manual-adjust function. 52
The remote control may be operated outside The remote control functions within a 26
of the remote control operation range. maximum range of 6 m (20 ft) and no more
than 30 degrees off-axis from the front
panel.

The function does not work properly Select My Beam and then try again. 51
because of the condition of the connected
components.

86 En
 Troubleshooting

■ Remote control
See
Problem Cause Remedy
page
The remote control does not Wrong distance or angle. The remote control functions within a 26
work and/or function maximum range of 6 m (20 ft) and no more
properly. than 30 degrees off-axis from the front
panel.

Direct sunlight or lighting (from an inverter Reposition this unit. —

type of fluorescent lamp, etc.) is striking the
remote control sensor of this unit.

The batteries are weak. Replace all batteries. 26

Cannot operate external The external component you want to operate Press INPUT on the front panel or the input 41
components with the remote is not selected as the input source. selector buttons on the remote control to
control of this unit. select the external component you want to
operate.

The remote control code was not correctly Set the remote control code correctly or try 79
set. another code for the same manufacturer
using the “List of remote control codes” at
the end of this manual.

Even if the remote control code is correctly Use the remote control supplied with the —
set, there are some models that do not external component.
respond to the remote control.

The cursor buttons do not The operation mode selector was Set the operation mode selector to YSP. —
work during SET MENU unwantedly set to TV/AV.
operation.

Cannot use the My Beam Wrong distance or angle. The remote control functions within a 51
auto-adjust function. maximum range of 6 m (20 ft) and no more
than 30 degrees off-axis from the front
panel.

INFORMATION
ADDITIONAL
English

87 En
Glossary

Glossary
■ Dolby Digital ■ DTS Digital Surround
Dolby Digital is a digital surround sound system that gives DTS digital surround was developed to replace the analog
you completely independent multi-channel audio. With 3 soundtracks of movies with a 6-channel digital sound
front channels (left, center, and right) and 2 surround track, and is now rapidly gaining popularity in movie
stereo channels, Dolby Digital provides 5 full-range audio theaters around the world. DTS, Inc. has developed a
channels. With an additional channel especially for bass home theater system so that you can enjoy the depth of
effects, called LFE (low-frequency effect), the system has sound and natural spatial representation of DTS digital
a total of 5.1-channels (LFE is counted as 0.1-channel). surround in your home. This system produces practically
By using 2-channel stereo for the surround channels, more distortion-free 6-channel sound (technically, left, right,
accurate moving sound effects and surround sound and center channels, 2 surround channels, plus an LFE
environment are possible than with Dolby Surround. The 0.1-channel as a subwoofer, for a total of 5.1 channels).
wide dynamic range (from maximum to minimum The unit incorporates a DTS-ES decoder that enables 6.1-
volume) reproduced by the 5 full-range channels and the channel reproduction by adding the surround back channel
precise sound orientation generated using digital sound to existing 5.1-channel format.
processing provide listeners with excitement and realism
previously unheard of. ■ DTS Neo:6
With this unit, any sound environment from monaural up Neo:6 decodes the conventional 2-channel sources for 6-
to a 5.1-channel configuration can be freely selected for channel playback by the specific decoder. It enables
your enjoyment. playback with the full-range channels with higher
separation just like digital discrete signal playback. Two
■ Dolby Pro Logic II modes are available: Music mode for playing music
Dolby Pro Logic II is an improved technique used to sources and Cinema mode for movies.
decode vast numbers of existing Dolby Surround software.
This new technology enables a discrete 5-channel ■ EUPHONY
playback with 2 front left and right channels, 1 center Euphony is a revolutionary sound field reproduction
channel, and 2 surround left and right channels (instead of system implemented with state-of-the-art sound
only 1 surround channel for conventional Pro Logic technologies developed under the basic concept of
technology). Music and Game modes are also available for enjoying beautiful sound. It can reproduce surround sound
2-channel sources in addition to the Movie mode. optimized without depending on the number of input
channels, the number of speakers (two or more speakers)
■ Dolby Surround or the speaker’s dimensions. In addition, it features steady
Dolby Surround uses a 4-channel analog recording system center localization. It also can reproduce the surround
to reproduce realistic and dynamic sound effects: 2 front sound for the headphones with natural sound and “out-of-
left and right channels (stereo), a center channel for dialog head” localization so that the listener feels an expanded
(monaural), and a surround channel for special sound sound and will not tire, even when listening to music or a
effects (monaural). The surround channel reproduces movie for long time.
sound within a narrow frequency range.
Dolby Surround is widely used with nearly all video tapes
and laser discs, and in many TV and cable broadcasts as
well. The Dolby Pro Logic decoder built into this unit
employs a digital signal processing system that
automatically stabilizes the volume on each channel to
enhance moving sound effects and directionality.

88 En
 Glossary

■ LFE 0.1-channel
This channel is for the reproduction of low bass signals.
The frequency range for this channel is 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low-frequency range compared to the full-range
reproduction by the other 5/6 channels in Dolby Digital or
DTS 5.1/6.1-channel systems.

■ PCM (Linear PCM)

Linear PCM is a signal format under which an analog
audio signal is digitized, recorded, and transmitted
without using any compression. This is used as a method
of recording CDs and DVD audio. The PCM system uses
a technique for sampling the size of the analog signal per
very small unit of time. Standing for pulse code
modulation, the analog signal is encoded as pulses and
then modulated for recording.

■ SRS TruBass
SRS TruBass is a psychoacoustic bass enhancement
technology developed by SRS Labs, Inc. for speakers and
headphone systems that delivers bass up to an octave
below the physical capabilities of the speaker’s driver.
SRS TruBass technology takes advantage of a
spontaneous tendency of the human ears to infer low-
range audio data when presented with higher-frequency
harmonic signals. As a result, our ears can hear the
original low-range sound that the speaker system is
incapable of producing.

INFORMATION
ADDITIONAL
English

89 En
 Index
■ Numerics ■ M
3 Beam ............................................................................ 45 MANUAL SETUP ..........................................................56
5 Beam ............................................................................ 44 MEMORY .......................................................................38
My Beam.........................................................................51
■ A
AC power supply cable ................................................... 25 ■ N
Audio pin cable............................................................... 17 Night listening enhancer .................................................53
AUTO SETUP (IntelliBeam).......................................... 31
■ O
■ B On-screen display (OSD) ................................................28
Battery............................................................................. 26 Optical cable ...................................................................17
BEAM MENU ................................................................ 58 OSD video pin cable .......................................................17
Beam mode ......................................................... 44, 50, 51
■ P
■ C PCM ................................................................................89
Cable clamp .................................................................... 17 Power...............................................................................27
Cardboard microphone stand.......................................... 33
■ R
■ D Rear panel .........................................................................9
DEMO MODE................................................................ 74 Remote control ................................................................10
Demonstration DVD ......................................................... 6 Remote control code .......................................................79
Digital audio pin cable.................................................... 17 Remote control sensor.....................................................26
DISPLAY MENU ........................................................... 66
Dolby Digital .................................................................. 46 ■ S
Dolby Pro Logic.............................................................. 46 SET MENU.....................................................................28
Dolby Pro Logic II.......................................................... 46 Sleep timer ......................................................................54
DTS................................................................................. 46 Stereo plus 3 Beam .........................................................45
DTS Neo: 6 ..................................................................... 46 Surround mode ................................................................46
Dynamic range................................................................ 63 Surround sound ...............................................................44
SOUND MENU ..............................................................62
■ E Stereo sound ....................................................................50
EUPHONY ..................................................................... 88 System parameter ............................................................71

■ F ■ T
FACTORY PRESET ....................................................... 77 Test tone ..........................................................................67
Front panel ........................................................................ 7 TruBass............................................................................63
Front panel display ........................................................... 8 TV macro ........................................................................83
TV volume equal mode...................................................53
■ I
IntelliBeam ..................................................................... 31 ■ V
IntelliBeam microphone ................................................. 32 Volume ............................................................................43
Volume mode ..................................................................53
■ L
LFE 0.1-channel ............................................................. 89

90 En
 Specifications

Specifications
AMP SECTION GENERAL
• Power Supply
• Maximum Output Power (JEITA)
................................................. 2 W (1 kHz, 10% THD, 4 Ω) × 16 [Australia model] ................................. AC 220–240 V, 50/60 Hz
15 W (100 Hz, 10% THD, 4 Ω) × 2 [U.K. and Europe models] ................... AC 220–240 V, 50/60 Hz
[Korea model] ...................................... AC 220–240 V, 50/60 Hz
SPEAKER SECTION [General model] ................................... AC 110–120 V, 50/60 Hz
• Driver [Asia model] .......................................... AC 220–240 V, 50/60 Hz
Small dia. speakers • Power Consumption ................................................................. 22 W
................... 2.8 cm (1-3/32 in) cone magnetic shielding type × 16
Woofers • Standby Power Consumption ...................................... 0.1 W or less
........................ 8 cm (3-5/32 in) cone magnetic shielding type × 2 • Dimensions (W x H x D) ................................ 610 × 120 × 220 mm
(24 x 4-23/32 x 8-21/32 in)
CONNECTIONS • Weight ............................................................. 8.5 kg (18 lbs 12 oz)
• Input Jacks
TV/STB, VCR AUDIO IN (1 V, 32 kΩ) ............. 2 pairs (Analog)
TV/STB, AUX OPTICAL DIGITAL IN .......... 2 (Optical digital)
* Specifications are subject to change without notice.
DVD COAXIAL DIGITAL IN ......................... 1 (Coaxial digital)
• Output Jacks
SUBWOOFER OUT (1.5 V, less than 120 Hz) ...... 1 (Subwoofer)
VIDEO OUT (1 Vp-p, 75 Ω) ............................................ 1 (OSD)
• System Connector Jack
INTELLIBEAM MIC .................................. 1 (Microphone input)
SYSTEM CONNECTOR ..................................1 (System control)

INFORMATION
ADDITIONAL
English

91 En
 Limited Guarantee for European Economic Area (EEA) and Switzerland
Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from
whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our
website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).
The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha
undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge
for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been
discontinued or is considered uneconomic to repair.
Conditions
1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a
statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the
product may be returned at the customer’s expense.
2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.
3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.
4. The following are excluded from this guarantee:
a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.
b. Damage resulting from:
(1) Repairs performed by the customer himself or by an unauthorised third party.
(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to
ensure the product is adequately packaged when returning the product for repair.
(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the proper
use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in
the country where it is used.
(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.
(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.
(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety
standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.
(7) Non AV (Audio Visual) related products.
(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or
http://www.yamaha-uk.com/ for U.K. resident.)
5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.
6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the
product.
7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.
8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising
from their sales/purchase contract.

92 En
TOSHIBA 335, 389
TOTEVISION 363, 396
UNITECH 363
UNIVERSUM 396, 327, 376
VIDEOSONIC 363
W.WHOUSE 396
WARDS 395, 396, 336,
362, 397, 363
YAMAHA 399, 392, 393, 394
ZERITH 344, 361, 368,
371, 379, 396, 397

CABLE TV TUNER
ABC 739, 752, 753,
755, 758, 759, 762
GENERAL INSTRUMENT
722
HAMIN 723, 724, 725,
726, 727
HITACHI 722
JEROLD 722, 728, 729,
732, 733, 734,
735, 736, 737
MAGNAVOX 738
MOTOROLA 748
OAK 739, 742, 743
PANASONIC 744, 745, 746,
747, 783, 784
PHILLIPS 763, 764, 765,
766, 767, 768
PIONEER 748, 785, 747
RADIO SHACK749
SCIENTIFIC ATLANTA
752, 753, 754
SONY 756, 757
TOCOM 755
UNIVERSAL 769, 772, 773,
774, 775
VIEWSTAR 764, 766, 776,
777, 778, 779, 782

SATELLITE TUNER
ECHOSTAR 822
GE 837, 838, 839
GENERAL INSTRUMENT
823
HITACHI 824
HUGHES 843, 844, 845, 846
JVC 822
MAGNAVOX 825
PANASONIC 826, 829
PHILLIPS 825, 843, 844,
845, 846, 847,
848, 849
PRIMESTAR 827
PROSCAN 837, 838, 839, 842
RADIO SHACK
828
RCA 837, 838, 839, 842
SAMSUNG 852
SONY 832, 835
TOSHIBA 833, 836
UNIDEN 825
ZENITH 834

ii
YSP-500_G-cv.fm Page 1 Thursday, September 20, 2007 8:49 AM

YSP-500

YSP-500
Digital Sound ProjectorTM
Système Acoustique Numérique

OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
© 2007 All rights reserved. BRUKSANVISNING
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
GEBRUIKSAANWIJZING
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA Printed in Malaysia WM28790
 Items used for connections and operations
in this guide
s Audio pin cable (x1)
2 Connecting external components to this unit
s OSD* video pin cable (x1)
s Optical cable (x1) Connecting external components such as a TV or DVD player to this unit.
YSP-500 s Digital audio pin cable (x1)
s IntelliBeam microphone (x1)
s Cardboard microphone stand (x1)
s Demonstration DVD (x1)
Connect your TV or DVD player to this unit using appropriate cables as shown below. After all connections are complete, plug the power supply cable into the AC wall outlet.
For further information on connecting other components, see pages 16 to 24 in the Owner’s Manual.

QUICK REFERENCE GUIDE *OSD: On-Screen Display

This connection example shows a way to connect external components such as a TV or DVD player to this unit by using the supplied cable. You can enjoy the multi-channel audio from the DVD player and the analog/digital audio from the TV.
Use the video pin cable supplied with your DVD player to make a video connection between your DVD player and TV.
This quick reference guide explains steps to connect a TV and a DVD player to this unit and achieve the
surround sound effects in a quick, easy manner. For detailed operation, refer to the Owner’s Manual.
TV

1 Installing this unit

Connect the supplied cables in the following order.
Decide where to install this unit. DVD player
Install this unit where there are no objects such as furniture obstructing the path of sound beams. Otherwise, the desired 1 Audio pin cable
Video connection
surround sound effects may not be achieved. You may install this unit in parallel with the wall or in the corner. (Outputs TV analog audio sounds from this unit)

2 OSD video pin cable

Install this unit in the exact center of the wall when it is Install this unit in the corner at a 40˚ to 50˚ angle from the
(Displays the YSP-500 menu screen on the TV)
measured from the left and right corners. adjacent walls.
3 Optical cable
(Outputs TV digital audio sounds from this unit)
An object, such as furniture An object, such as furniture ANALOG AUDIO VIDEO OPTICAL COAXIAL
OUTPUT INPUT AUDIO OUTPUT AUDIO OUTPUT 4 Digital audio pin cable
1. Pull out the cap Optical cable
L 1 (Outputs DVD digital audio sounds from this unit)

Front left channel 40˚ to 50˚ Front left channel Pull out the cap
R 2 before connecting
Center channel Center channel
the optical cable,
2. Check the direction and then check the
Front right channel Front right channel
direction to insert
Note
Surround left channel Surround left channel the cable.
Check whether the digital audio output of your TV and DVD
Surround right channel Surround right channel player is turned on.

YSP-500
Install this unit using a rack, etc. 1 2 3 4
Depending on your installation environment, connections with external components (see “2 Connecting external components to this unit”) can be done before
installing this unit. We recommend that you temporarily place and arrange all components in order to decide which procedure must come first. L

For further information on installation, see page 13 in the Owner’s Manual. R

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

The following is an example of installing this unit in a rack.

To the AC wall
1 Place this unit in front of 2 Connect this unit 3 Install this unit in the 4 Installation is completed. outlet
L
the rack. to your TV and DVD player. rack.
If a subwoofer is connected to this unit, turn on the power of your
R subwoofer and then carry out the AUTO SETUP procedure (see the

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

backside) or select “SWFR” for “BASS OUT” in “SUBWOOFER SET” (see
OPTICAL COAXIAL CONNECTOR page 62 in the Owner’s Manual).
AUDIO INPUT OUT DIGITAL INPUT Do not plug the power
supply cable into an AC
wall outlet until all
connections are complete.
System connection

y Hint
Audio connection
To enjoy better surround effects, place this unit on the upper shelf to keep it away from the floor. If you have connected external components,
Note follow the steps on the backside to start the Continued
Be careful not to leave scratches on this unit or the rack. Subwoofer on the back
AUTO SETUP procedure.

Printed in Malaysia WM28850 [En] C2007 All rights reserved.

0906_YSP-500_En_guide.p65 1 9/7/07, 11:18 AM

 Continued from the front

3 Carry out the AUTO SETUP (IntelliBeam) 6 Set the operation mode selector 10 Press ENTER to start the AUTO 4 Enjoying surround sound
to YSP. SETUP procedure, and then
Carry out the AUTO SETUP to adjust the settings that best match your This unit switches to the YSP operation mode.
leave the room within 10 seconds. Enjoy TV or DVD digital audio in surround sound.
For instructions on how to operate or set your TV or DVD player, refer to the owner’s manual supplied with each component.
listening environment The following screen appears on the TV. Leave the room
within 10 seconds before the AUTO SETUP procedure
The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output
starts.
during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress. CH LEVEL MENU Enjoying DVDs in surround sound Enjoying TV in surround sound
1 Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC ENTER
TV/AV
1 Select the DVD video input on 1 Select the TV channel using the
YSP CH LEVEL MENU
AUTO SETUP START
jack on the front panel. TEST RETURN
Will begin in 10sec your TV. remote control supplied with
TV/AV Please leave the room
You may want to use the supplied cardboard microphone stand for the AUTO SETUP. Assemble the stand and place the IntelliBeam ENTER

microphone on top of it as shown below. TEST

YSP
RETURN
**--------
[RETURN]:Cancel your TV.

1 2 3 4 7 Press and hold AUTO SETUP for The setup screen automatically changes during the AUTO
SETUP procedure. 2 Set the operation mode selector 2 Set the operation mode selector
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON more than 2 seconds. When the AUTO SETUP procedure is completed, the
The menu screen appears on the TV. following screen appears on the TV. to YSP. to YSP.
INTELLIBEAM MIC
If the menu screen does not appear, check the OSD video This unit switches to the YSP operation mode. This unit switches to the YSP operation mode.
pin cable (see the connection example on the front page). SHOW RESULT
MEASUREMENT COMPLETE
IntelliBeam microphone (supplied) BEAM MODE :5 BEAM

TV
INPUT1
TV
INPUT2 MACRO AUTO SETUP
PREPARATION & CHECK
SUBWOOFER :NOT APPLICABLE
ENTER
TV/AV
ENTER
TV/AV
YSP YSP
Cardboard microphone stand (supplied) AUTO
Please connect the MIC.
[ENTER]:Save set-up
[RETURN]:Do not save set-up
VOL MODE SETUP INPUTMODE SLEEP
Please place the MIC at least TEST RETURN TEST RETURN
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.
5BEAM ST+3BEAM 3BEAM Measurement takes about 3min.
After [ENTER] is pressed, If “ENVIRONMENT CHECK (FAILED) is displayed, see page
1 2 3 please leave the room.
[ENTER]:Start [RETURN]:Cancel 36 in the Owner’s Manual and then run the procedure again.
2 Set the IntelliBeam microphone at your normal listening position.
Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would
3 1) Press DVD on the remote 3 Press TV on the remote control
y Hint
be when you are seated. 8 Check the following points. • The result may differ depending on the environment. control of this unit. of this unit.
About the IntelliBeam microphone • If any error occurs, the corresponding error message appears This unit switches to the DVD playback mode. This unit switches to the TV playback mode.
Place the IntelliBeam microphone on • Is the microphone placed on an imaginary center line drawn on the screen. In this case, see “Error messages for AUTO
the extended center line of this unit
from this unit? SETUP” on page 37 in the Owner’s Manual and then follow STB VCR DVD AUX STB VCR DVD AUX
and 1.8 m (6.0 ft) or more away from the instructions. To start the AUTO SETUP procedure once INPUT1
TV
INPUT2 MACRO TV

it. Also, make sure place the • Is the microphone placed within 1 m (3.3 ft) upper or lower again, press RETURN. TV
INPUT1 INPUT2 MACRO
IntelliBeam Upper bound TV
microphone
position of the IntelliBeam microphone within 1 m from the center height of this unit? AUTO
VOL MODE SETUP INPUTMODE SLEEP

(3.3 ft) upper or lower from the center

Center height of
microphone
height of this unit.
• Is the microphone placed more than 1.8 m (6.0 ft) from the 2) Play back the supplied demonstration 5BEAM ST+3BEAM 3BEAM

this unit front of this unit? 1 2 3

Within 1 m
(3.3 ft)
About the room environment
11 Press ENTER. DVD on the DVD player.
• Is your listening room kept as quiet as possible?
Within 1 m
(3.3 ft) Center line The following screen appears on the TV for 2 seconds and
Cardboard Listening IntelliBeam then the menu screen disappears from the TV.
microphone stand Cardboard
position microphone
microphone MULTI indicator
More than 1.8 m (6.0 ft) Lower bound position
of the microphone
stand
9 Prepare to leave the room. CH LEVEL MENU
4 Check the multi-channel digital signal being output at this unit.
The best setting may not be done if you are in the room. AUTO SETUP COMPLETE The MULTI indicator and/or (see page 42 in the Owner’s Manual) is lit in the front panel display. If the sound is
Prepare to leave the room in 10 seconds after pressing TV/AV Please remove the MIC from output from your TV speakers, mute the volume on your TV. For details about digital audio input signals, see
the YSP and the listening
ENTER in step 10. ENTER
YSP position. page 46 in the Owner’s Manual.

3 Press STANDBY/ON on the TEST RETURN

4 Turn on the power of your TV. y Hint

remote control. • When leaving the room, bring this guide with you.
• Wait outside the room during the AUTO SETUP procedure. VOLUME CH TV VOL

The power of this unit turns on.

Before operations, insert batteries into the remote control
• The AUTO SETUP procedure takes about 3 minutes. 5 Press VOLUME +/- on the remote control to adjust the volume
• To cancel the AUTO SETUP procedure after it is started,
(see page 26 in the Owner’s Manual). press RETURN. 12 Disconnect the IntelliBeam level of this unit.
If necessary, adjust the volume level of this unit. MUTE TV INPUT TV MUTE
If you have connected the subwoofer, set the volume and
crossover/high cut frequency. Refer to the note on page
5 Select the appropriate video microphone.
32 in the Owner’s Manual. The AUTO SETUP has completed. Keep the IntelliBeam
input on your TV. microphone in a safe place.
The settings are automatically saved in the system memory.
Subwoofer “YSP-500” appears on your TV. If the OSD video pin cable
is connected to the video input 1 on the TV as shown in the
6 Press one of the beam mode buttons on the remote control 5BEAM ST+3BEAM 3BEAM

VOLUME CROSSOVER/ 1 2 3
STANDBY/ON POWER POWER
HIGH CUT
connection example, switch the video input to “1”. to select the desired beam mode. STEREO

4
MY BEAM

5
MY SUR.

6
AV TV
Select one of the six beam modes that best matches the current input source of this unit.
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON
For further information on the beam modes, see page 44 in the Owner’s Manual.
MIN MAX MIN MAX

INTELLIBEAM MIC To fine-tune the listening environment parameters manually or make advanced settings for speaker positions,
sound beams, etc., see “MANUAL SETUP” on page 56 in the Owner’s Manual.

0905_YSP-500_En_guide.p65 2 9/6/07, 5:05 PM

 Articles utilisés pour les raccordements et
les opérations
s Câble audio à fiches cinch (x1)
2 Raccordement de composants à cet appareil
s Câble vidéo à fiches cinch pour affichage des informations OSD* (x1)
s Câble à fibres optiques (x1) Raccordement de composants, tel qu’un téléviseur ou un lecteur de DVD à cet appareil.
YSP-500 s Câble audionumérique à fiches cinch (x1)
s Microphone IntelliBeam (x1)
s Support de microphone plat (x1)
s DVD de démonstration (x1)
Raccordez votre téléviseur ou lecteur de DVD à cet appareil en utilisant les câbles appropriés, comme indiqué ci-dessous. Lorsque tous les appareils sont raccordés, branchez le câble d’alimentation sur une prise secteur.
Pour de plus amples informations sur le raccordement d’autres composants, reportez-vous aux pages 16 à 24 du mode d’emploi.

GUIDE DE REFERENCE RAPIDE *OSD: Affichage des menus sur l’écran de télévision
Cet exemple montre comment raccorder des composants, tels qu’un téléviseur ou un lecteur de DVD à cet appareil à l’aide du câble fourni. Vous pourrez profiter du son multivoies du lecteur de DVD et du son analogique ou numérique du téléviseur.
Utilisez le câble cinch vidéo fourni avec votre lecteur de DVD pour établir une liaison vidéo entre le lecteur de DVD et le téléviseur.
Ce guide de référence rapide explique comment procéder pour raccorder un téléviseur et un lecteur de DVD à cet appareil et obtenir rapidement,
de la manière la plus simple, des effets ambiophoniques. Pour de plus amples informations à ce sujet, reportez-vous au mode d’emploi.
TV

1 Installation de l’appareil
Raccordez les câbles fournis dans l’ordre suivant.
Déterminez l’emplacement de cet appareil. Graveur de DVD
Installez l’appareil à un endroit où des meubles ou d’autres objets ne risquent pas de faire obstacle aux faisceaux sonores émis. Sinon, vous 1 Câble audio à fiches cinch
Liaison vidéo
n’obtiendrez pas les effets d’ambiance souhaités. Vous pouvez installer cet appareil parallèlement à un mur ou dans un angle de la pièce. (Transmet les signaux audio analogiques du téléviseur via cet appareil)

2 Câble vidéo à fiches cinch pour affichage des informations OSD

Installez cet appareil au centre du mur dans le sens de la Installez cet appareil dans un angle du mur à 40° à 50° des
(Affiche les menus du YSP-500 sur l’écran du téléviseur)
longueur. murs adjacents.
3 Câble à fibres optiques
(Transmet les signaux audio numériques du téléviseur via cet appareil)
Un objet, par exemple un meuble Un objet, par exemple un meuble ANALOG AUDIO VIDEO OPTICAL COAXIAL
OUTPUT INPUT AUDIO OUTPUT AUDIO OUTPUT 4 Câble audionumérique à fiches cinch
1. Déposez le capuchon. Câble à fibres
L 1 (Transmet les signaux audio numériques du lecteur de
optiques
DVD via cet appareil)
Voie avant gauche 40° à 50° Voie avant gauche Déposez le
R 2 capuchon avant de
Voie centrale Voie centrale
brancher le câble
2. Vérifiez le sens. optique, puis
Voie avant droite Voie avant droite
vérifiez le sens
Remarque
Voie d’ambiance gauche Voie d’ambiance gauche d’insertion de la
fiche. Vérifiez si la sortie audio numérique de votre téléviseur et de
Voie d’ambiance droite Voie d’ambiance droite votre lecteur de DVD est en service.

YSP-500
Installez cet appareil dans un meuble, etc. 1 2 3 4
Selon la situation, les raccordements aux composants pourront être effectués avant l’installation de cet appareil (voir “2 Raccordement de composants à cet
appareil”). Il est conseillé de placer et de disposer provisoirement tous les appareils de manière à voir ce qu’il convient de faire en premier. L

Pour de plus amples informations sur l’installation, reportez-vous à la page 13 du mode d’emploi. R

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

L’installation dans un meuble est expliquée dans l’exemple suivant.

À une prise
1 Posez cet appareil devant 2 Raccordez cet appareil au 3 Installez l’appareil dans 4 L’installation est terminée.
secteur
le meuble. téléviseur et au lecteur de le meuble. L

DVD. Si un caisson de graves est connecté à l’appareil, mettez votre caisson

R de graves sous tension et exécutez la procédure AUTO SETUP (voir au

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

verso) ou sélectionnez “SWFR” pour “BASS OUT” dans “SUBWOOFER
OPTICAL COAXIAL CONNECTOR SET” (voir page 62 du Mode d’emploi). Ne branchez le câble
AUDIO INPUT OUT DIGITAL INPUT
d’alimentation sur une prise
secteur que lorsque tous
les appareils ont été
Connexion système raccordés.

y Conseil
Liaison audio
Pour bénéficier d’un meilleur effet ambiophonique, posez l’appareil sur l’étagère supérieure du meuble de manière à ce qu’il soit le plus loin possible du sol. Si vous avez raccordé des composants,
Remarque suivez les étapes au verso pour effectuer la Suite au
Attention de ne pas rayer l’appareil ou le meuble. Caisson de graves verso
procédure AUTO SETUP.

Printed in Malaysia WM28860 [Fr] C2007 All rights reserved.

0906_YSP-500_Fr_guide.p65 1 9/6/07, 5:08 PM

 Suite du recto

3 Exécution de AUTO SETUP (IntelliBeam) 6 Réglez le sélecteur de mode de 10 Appuyez sur ENTER pour lancer la 4 Écoute du son ambiophonique
fonctionnement sur YSP. procédure AUTO SETUP, puis quittez
Exécutez AUTO SETUP pour obtenir les réglages les mieux adaptés à votre L’appareil se met en mode de fonctionnement YSP.
la pièce dans les 10 secondes. Écoutez le son numérique de la télévision ou de vos DVD en ambiophonie.
Pour le détail sur le fonctionnement ou le réglage du téléviseur ou du lecteur de DVD, reportez-vous à leur manuel respectif.
environnement. L’écran suivant apparaît sur le téléviseur. Quittez la pièce
dans les 10 secondes, avant que la procédure AUTO
La technologie IntelliBeam permet d’obtenir les réglages les mieux adaptés à votre environnement. Pendant la procédure AUTO SETUP, il est normal
SETUP démarre.
d’entendre des signaux d’essai puissants. Ne laissez pas d’enfants dans la pièce pendant l’exécution de AUTO SETUP. CH LEVEL MENU Regarder des DVD en ambiophonie Regarder la télévision en ambiophonie
1 Raccordez le microphone IntelliBeam fourni à la prise INTELLIBEAM MIC ENTER
TV/AV
1 Sélectionnez l’entrée vidéo du 1 Sélectionnez la chaîne de télévision
YSP CH LEVEL MENU

sur la face avant. TEST RETURN

DVD sur votre téléviseur. avec le boîtier de télécommande

TV/AV
Vous pouvez utiliser le support de microphone en carton fourni lors de la procédure AUTO SETUP. Assemblez le support et posez le ENTER

microphone IntelliBeam dessus, comme indiqué ci-dessous. TEST

YSP
RETURN
fourni avec votre téléviseur.

1 2 3 4 7 Appuyez sur AUTO SETUP et maintenez L’écran de configuration change automatiquement pendant
toute la procédure AUTO SETUP. 2 Réglez le sélecteur de mode de 2 Réglez le sélecteur de mode de
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON la pression plus de 2 secondes. Lorsque la procédure AUTO SETUP est terminée, l’écran
Le menu apparaît sur l’écran de télévision. suivant apparaît sur l’écran de télévision. fonctionnement sur YSP. fonctionnement sur YSP.
INTELLIBEAM MIC
S’il n’apparaît pas, vérifiez le câble cinch vidéo OSD L’appareil se met en mode de fonctionnement YSP. L’appareil se met en mode de fonctionnement YSP.
(voir l’exemple de raccordement sur le recto).

Microphone IntelliBeam (Fourni)

TV TV/AV TV/AV
INPUT1 INPUT2 MACRO
ENTER ENTER
TV YSP YSP
Support de microphone plat (Fourni) AUTO
VOL MODE SETUP INPUTMODE SLEEP TEST RETURN TEST RETURN

5BEAM ST+3BEAM 3BEAM

Si “ENVIRONMENT CHECK (FAILED)” apparaît, reportez-vous à la
1 2 3
page 36 du mode d’emploi et effectuez une nouvelle fois la procédure.
2 Posez le microphone IntelliBeam à votre position d’écoute habituelle.
Utilisez le support de microphone en carton fourni ou un trépied pour placer le microphone IntelliBeam à la hauteur de vos oreilles
y Conseil 3 1) Appuyez sur DVD du boîtier de 3 Appuyez sur TV sur le boîtier de
Vous pouvez sélectionner la langue indiquée dans les y Conseil
lorsque vous êtes assis.
informations OSD en procédant de la façon suivante. • Le résultat peut être différent selon l’environnement. télécommande de cet appareil. télécommande de cet appareil.
Réglez le sélecteur de mode de fonctionnement sur YSP. ➞ • En cas d’erreur, le message d’erreur correspondant apparaît L’appareil se met en mode de lecture de DVD. L’appareil se met en mode Télévision.
Placez le microphone IntelliBeam sur Appuyez sur MENU. ➞ Appuyez sur / pour sélectionner sur l’écran. Dans ce cas, reportez-vous à “Message d’erreur
l’axe central à 1,8 m au minimum de LANGUAGE SETUP. ➞ Appuyez sur ENTER. ➞ Appuyez sur pour AUTO SETUP” à la page 37 du mode d’emploi et suivez STB VCR DVD AUX STB VCR DVD AUX
l’appareil. Assurez-vous aussi que le / pour sélectionner la langue. ➞ Appuyez sur ENTER. les instructions. Pour relancer la procédure AUTO SETUP, INPUT1
TV
INPUT2 MACRO INPUT1
TV
INPUT2 MACRO
Microphone microphone IntelliBeam est à moins appuyez sur RETURN. TV TV
IntelliBeam de 1 m au-dessus ou au-dessous de AUTO
Limite supérieure VOL MODE SETUP INPUTMODE SLEEP

la hauteur centrale de cet appareil.

Hauteur centrale
du microphone
2) Reproduisez le DVD de démonstration 5BEAM ST+3BEAM 3BEAM

de cet appareil 8 Vérifiez les points suivants. 1 2 3

Moins de 1 m
En ce qui concerne le microphone IntelliBeam
11 Appuyez sur ENTER. fourni sur le lecteur de DVD.
Moins de 1 m • Est-ce que le microphone est placé dans l’axe de cet
Axe L’écran suivant apparaît sur le téléviseur pendant
Support de appareil?
microphone plat
Position Support de Microphone 2 secondes, puis il disparaît.
d’écoute microphone IntelliBeam • Est-ce que le microphone est à moins de 1 m au-dessus ou Témoin MULTI
Plus de 1,8 m Limite inférieure du
microphone
plat
au-dessous de la hauteur centrale de cet appareil? CH LEVEL MENU
4 Vérifiez le signal numérique multivoies fourni par cet appareil.
• Est-ce que le microphone est à plus de 1,8 m de l’avant de cet Le témoin MULTI (voir page 42 du mode d’emploi) s’éclaire sur l’afficheur de la face avant. Si le son est fourni
appareil? TV/AV
par les enceintes de votre téléviseur, coupez le son sur votre téléviseur. Pour de plus amples informations sur
En ce qui concerne l’environnement de la pièce ENTER
YSP
les signaux d’entrée audio numérique, reportez-vous à la page 46 du mode d’emploi.
• Est-ce que la pièce est la plus silencieuse possible?
3 Appuyez sur STANDBY/ON sur TEST RETURN

4 Mettez le téléviseur sous tension.

le boîtier de télécommande. VOLUME CH TV VOL

L’appareil se met sous tension. 9 Préparez-vous à quitter la pièce. 5 Appuyez sur VOLUME +/– du boîtier de télécommande pour
N’oubliez de mettre auparavant des piles dans le boîtier de
Vous n’obtiendrez peut-être pas le meilleur réglage possible si
télécommande (voir page 26 du mode d’emploi).
vous restez dans la pièce. Préparez-vous à quitter la pièce dans 12 Débranchez le microphone régler le niveau de sortie de cet appareil.
Si nécessaire, réglez le niveau de sortie de cet appareil.
les 10 secondes après avoir appuyé sur ENTER à l’étape 10. MUTE TV INPUT TV MUTE
Si vous avez raccordé le caisson de graves, réglez le
volume et la fréquence de coupure des hautes fréquences.
5 Sélectionnez l’entrée vidéo IntelliBeam.
Reportez-vous à la remarque à la page 32 du mode y Conseil La procédure AUTO SETUP est terminée. Rangez le
d’emploi.
appropriée sur votre téléviseur. • Lorsque vous quittez la pièce, emportez le guide avec vous. microphone Intellibeam en lieu sûr.
Les réglages sont automatiquement sauvegardés dans la
Subwoofer “YSP-500” apparaît sur votre téléviseur. Si le câble cinch vidéo
OSD est raccordé à l’entrée vidéo 1 du téléviseur, comme indiqué
• Attendez à l’extérieur de la pièce pendant toute la durée de la
mémoire du système.
6 Appuyez sur une des touches du mode de faisceaux sur le boîtier 5BEAM ST+3BEAM 3BEAM

VOLUME CROSSOVER/ procédure AUTO SETUP. 1 2 3

STANDBY/ON POWER POWER
HIGH CUT
dans l’exemple de raccordement, réglez l’entrée vidéo sur “1”. • La procédure AUTO SETUP dure 3 minutes environ. de télécommande pour sélectionner le mode de faisceaux souhaité. STEREO MY BEAM MY SUR.

AV TV • Pour annuler la procédure AUTO SETUP en cours d’exécution, 4 5 6

Sélectionnez le mode de faisceaux le mieux adapté à la source actuellement sélectionnée parmi les six modes proposés.
appuyez sur RETURN.
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON
Pour de plus amples informations sur les modes de faisceaux, reportez-vous à la page 44 de mode d’emploi.
MIN MAX MIN MAX

INTELLIBEAM MIC Pour régler plus finement les paramètres de l’environnement d’écoute ou pour faire des réglages encore plus sophistiqués pour les positions
des enceintes, les faisceaux sonores, etc. reportez-vous à “MANUAL SETUP” (Configuration manuelle) à la page 56 du mode d’emploi.

0906_YSP-500_Fr_guide.p65 2 9/6/07, 5:08 PM

 Teile für Anschluss und Betrieb
s Audio-Cinchkabel (x1)
2 Anschluss externer Komponenten an diesem Gerät
s OSD*-Video-Cinchkabel (x1)
s Optokabel (x1)
s Digitales Audio-Cinchkabel (x1)
Verbinden des Geräts mit externen Komponenten wie Fernsehgerät und DVD-Player.
YSP-500 s IntelliBeam Mikrofon (x1)
s Pappständer für Mikrofon (x1)
s Demo-DVD (x1)
Schließen Sie Fernsehgerät, DVD-Player u. dgl. mit geeigneten Kabeln wie nachfolgend beschrieben an. Nach Herstellen aller anderen Verbindungen schließen Sie dann noch das Netzkabel an eine Steckdose an.
Weitere Informationen zum Anschluss anderer Komponenten finden Sie in der Bedienungsanleitung auf den Seiten 16 bis 24.

KURZ-ANLEITUNG *OSD: Bildschirmanzeige (On-Screen Display)

Dieses Anschlussbeispiel veranschaulicht eine Möglichkeit für den Anschluss externer Komponenten wie Fernsehgerät und DVD-Player mit den mitgelieferten Kabeln. Mehrkanalton vom DVD-Player und analoge/dititale Tonsignale vom Fernsehgerät genießen.
Stellen Sie mit Hilfe des mit dem DVD-Player gelieferten Video-Cinchkabels eine Video-Verbindung zwischen dem DVD-Player und dem Fernsehgerät her.
Diese Kurz-Anleitung erläutert in kurzer und übersichtlicher Form, wie Sie dieses Geräts mit einem Fernsehgerät und einem DVD-Player
verbinden und Surroundklang-Effekte genießen. Ausführliche Anweisungen zur Bedienung finden Sie in der Bedienungsanleitung.
TV

1 Installieren dieses Gerätes

Schließen Sie das mitgelieferte Kabel in der folgenden Reihenfolge her.
Bestimmung des richtigen Aufstellungsorts DVD-Player
Installieren Sie dieses Gerät an einem Ort, wo der Schallstrahlengang durch keine Hindernisse, wie z.B. Möbelstücke, beeinträchtigt wird. Anderenfalls 1 Audio-Cinchkabel
Video-Verbindung
werden die gewünschten Surroundklangeffekte möglicherweise nicht erzielt. Sie können dieses Gerät parallel zur Wand oder in einer Ecke installieren. (Zur Ausgabe analoger Fernseh-Audiosignale über dieses Gerät.)

Installieren Sie dieses Gerät genau in der Mitte der Wand, Installieren Sie dieses Gerät in einer Ecke in einem Winkel 2 OSD-Video-Cinchkabel
von der linken und rechten Ecke aus gemessen. von 40˚ bis 50˚ zu den angrenzenden Wänden. (Zum Einblenden der YSP-500 Menüanzeige am Fernsehbildschirm.)

3 Optokabel
(Zur Ausgabe digitaler Fernseh-Audiosignale über dieses Gerät.)
Ein Hindernis, wie zum Beispiel ein Möbelstück Ein Hindernis, wie zum Beispiel ein Möbelstück ANALOG AUDIO VIDEO OPTICAL COAXIAL
OUTPUT INPUT AUDIO OUTPUT Optokabel AUDIO OUTPUT 4 Digitales Audio-Cinchkabel
1. Kappe herausziehen
L 1 (Zur Ausgabe digitaler DVD-Audiosignale über dieses Gerät.)
Vorderer linker Kanal 40˚ bis 50˚ Vorderer linker Kanal Ziehen Sie vor
R 2 dem Anschluss
Center-Kanal Center-Kanal
des Optokabels
2. Korrekt ausrichten die Kappe heraus
Vorderer rechter Kanal Vorderer rechter Kanal
und richten Sie
Hinweis
Linker Surround-Kanal Linker Surround-Kanal den Stecker beim
Anschluss korrekt Sehen Sie nach, ob der digitale Audio-Ausgang an
Rechter Surround-Kanal Rechter Surround-Kanal aus. Fernsehgerät und DVD-Player eingeschaltet ist.

YSP-500
Installation des Geräts in einem Gestell o. dgl. 1 2 3 4
Die Verbindungen mit externen Komponenten (siehe „2 Anschluss externer Komponenten an diesem Gerät“) können je nach Installationsumgebung vor der
Aufstellung des Geräts erfolgen. Wir empfehlen Ihnen, dieses Gerät und alle anderen Komponenten zunächst provisorisch anzuordnen um zu sehen, in L

welcher Reihenfolge Sie vorgehen müssen. R

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

COAXIAL CONNECTOR

Ausführliche Anweisungen zur Installation finden Sie in der Bedienungsanleitung auf Seite 13.
OPTICAL
AUDIO INPUT OUT DIGITAL INPUT

Das folgende Beispiel zeigt die Aufstellung in einem Gestell.

An die
1 Stellen Sie das Gerät vor 2 Schließen Sie dieses 3 Stellen Sie das Gerät in 4 Die Aufstellung ist damit Wandsteckdose
L
dem Gestell auf dem Boden Gerät an Ihren Fernseher und das Gestell. abgeschlossen
Wenn ein Subwoofer an dieses Gerät angeschlossen ist, schalten Sie
ab. DVD-Player an.
R Ihren Subwoofer ein und führen dann das AUTO Setup-Verfahren aus

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

(siehe Rückseite) oder wählen Sie „SWFR“ für „BASS OUT“ in
OPTICAL COAXIAL CONNECTOR „SUBWOOFER SET“ (siehe Seite 62 im Bedienungshandbuch).
AUDIO INPUT OUT DIGITAL INPUT
Schließen Sie das Netzkabel
erst an die Steckdose an,
nachdem alle anderen
Verbindungen hergestellt
wurden.
Systemanschluss

y Tipp
Audio-Verbindung
Zur Optimierung der Surroundeffekte stellen Sie das Gerät in das obere Regalbrett. Ein gewisser Abstand zum Fußboden ist von Vorteil. Nachdem Sie die externen Komponenten
Hinweis angeschlossen haben, folgen Sie den Schritten auf Fortsetzung auf
Arbeiten Sie vorsichtig, damit weder am Gerät noch am Gestell Kratzer entstehen. Subwoofer der Rückseite
der Rückseite, um das AUTO SETUP zu starten.
(Tieftöner)

Printed in Malaysia WM28870 [De] C2007 All rights reserved.

0906_YSP-500_De_guide.p65 1 9/6/07, 8:21 PM

 Fortsetzung von der Vorderseite

3 Durchführung von AUTO SETUP (IntelliBeam) 6 Stellen Sie den 10 Drücken Sie ENTER, um den 4 Surroundklang-Wiedergabe
Betriebsmoduswähler auf YSP. AUTO SETUP-Vorgang zu starten,
Führen Sie das AUTO SETUP durch, um die Einstellungen der Das Gerät schaltet in den YSP-Betriebsmodus.
und verlassen Sie den Hörraum Genießen Sie digitale Fernseh- oder DVD-Tonsignale mit Surroundklang.
Anweisungen zur Bedienung und Einstellung Ihres Fernsehers oder DVD-Players entnehmen Sie bitte der Bedienungsanleitung der betreffenden Komponente.
Geräteparameter optimal an Ihre Hörumgebung anzupassen dann innerhalb von 10 Sekunden.
Die IntelliBeam-Technologie erlaubt Ihnen eine automatische Ermittlung der für Ihren Hörraum optimalen Soundeinstellungen. Während des AUTO SETUP-
Vorgangs werden laute Testtöne ausgegeben. Achten Sie darauf, dass sich im Verlauf des AUTO SETUP-Vorgangs keine Kinder im Hörraum befinden. CH LEVEL MENU
Die folgende Anzeige erscheint am Fernsehbildschirm.
Verlassen Sie den Raum innerhalb von 10 Sekunden, bevor
DVD-Wiedergabe mit Surroundklang Fernsehprogramme mit Surroundklang
der AUTO SETUP-Vorgang startet.
1 Schließen Sie das mitgelieferte IntelliBeam-Mikrofon an die INTELLIBEAM ENTER
TV/AV
1 Wählen Sie den DVD-Eingang 1 Wählen Sie mit der Fernbedienung
YSP CH LEVEL MENU

MIC-Buchse an der Frontblende an. TEST RETURN

am Fernsehgerät. des Fernsehgeräts das

TV/AV
Wir empfehlen die Verwendung des mitgelieferten Karton-Mikrofonständers für das AUTO SETUP. Bauen Sie den Ständer zusammen ENTER

und legen Sie das Mikrofon wie in der Abbildung oben auf den Ständer. TEST
YSP
RETURN
gewünschte Fernsehprogramm.

1 2 3 4 7 Halten Sie AUTO SETUP mindestens Die Setup-Anzeigen wechseln während des AUTO SETUP-
Vorgangs automatisch. 2 Stellen Sie den 2 Stellen Sie den
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON 2 Sekunden lang gedrückt. Nach Abschluss des AUTO SETUP-Vorgangs ist auf dem
Die Menüanzeige erscheint am Fernsehbildschirm. Fernsehbildschirm die folgende Anzeige zu sehen. Betriebsmoduswähler auf YSP. Betriebsmoduswähler auf YSP.
INTELLIBEAM MIC
Sollte die Menüanzeige nicht eingeblendet werden, Das Gerät schaltet in den YSP-Betriebsmodus. Das Gerät schaltet in den YSP-Betriebsmodus.
überprüfen Sie das OSD-Video-Cinchkabel (siehe
Anschlussbeispiel auf der Vorderseite).
IntelliBeam Mikrofon (mitgeliefert)
TV TV/AV TV/AV
INPUT1 INPUT2 MACRO
ENTER ENTER
TV YSP YSP
Pappständer für Mikrofon (mitgeliefert) AUTO
VOL MODE SETUP INPUTMODE SLEEP TEST RETURN TEST RETURN

5BEAM ST+3BEAM 3BEAM

Falls „ENVIRONMENT CHECK FAILED“ angezeigt wird,
1 2 3
lesen Sie auf Seite 36 in der Bedienungsanleitung nach und
2 Stellen Sie das IntelliBeam mikrofon an Ihrer normalen Hörposition auf. führen den Vorgang danach noch einmal durch.

y Tipp
3 1) Drücken Sie DVD an der 3 Drücken Sie TV an der
Verwenden Sie den mitgelieferten Karton-Mikrofonständer oder ein Stativ, damit das Mikrofon sich in derselben Höhe befindet wie Ihre
Ohren, wenn Sie an Ihrer Hörposition Platz nehmen. Sie können die in der Bildschirmanzeige gezeigte Sprache mit
den folgenden Schritten wählen.
y Tipp Fernbedienung dieses Geräts. Fernbedienung dieses Geräts.
• Das Ergebnis kann je nach Hörumgebung anders ausfallen. Das Gerät schaltet dabei in den DVD-Wiedergabemodus. Das Gerät schaltet in den TV-Wiedergabemodus.
Stellen Sie das IntelliBeam mikrofon Stellen Sie den Betriebsmoduswahlschalter auf YSP ➞ Drücken
• Wenn ein Fehler auftritt, erscheint eine entsprechende Fehlermeldung auf
entlang der verlängerten Mittenlinie Sie MENU ➞ Drücken Sie / zum Wählen von LANGUAGE
dem Bildschirm. Folgen Sie in einem solchen Fall den Anweisungen unter
des Geräts in mindestens 1,8 m SETUP ➞ Drücken Sie ENTER ➞ Drücken Sie / zum STB VCR DVD AUX STB VCR DVD AUX
„Fehlermeldungen für AUTO SETUP“ auf Seite 37 der Bedienungsanleitung. TV TV

Entfernung auf. Achten Sie unbedingt Auswählen der Sprache ➞ Drücken Sie ENTER INPUT1 INPUT2 MACRO INPUT1 INPUT2 MACRO
IntelliBeam Obere Zum erneuten Starten des AUTO SETUP-Vorgangs drücken Sie RETURN. TV TV
Mikrofon darauf, dass die Höhe des IntelliBeam AUTO
Grenzposition VOL MODE SETUP INPUTMODE SLEEP

mikrofons nicht mehr als 1 m von der

Mittenhöhe
des Mikrofons
Mittenlinie des Geräts abweicht.
2) Spielen Sie die mitgelieferte Demo- 5BEAM ST+3BEAM 3BEAM

dieses Geräts 1 2 3
Innerhalb 1 m 8 Prüfen Sie folgende Punkte. DVD auf dem DVD-Player ab.
Bezüglich des IntelliBeam-Mikrofons
11 Drücken Sie ENTER.
Innerhalb 1 m Die folgende Anzeige erscheint 2 Sekunden lang am
Pappständer für
Mittellinie • Ist das Mikrofon entlang der imaginären, vom Gerät
Mikrofon Hörposition Pappständer IntelliBeam Fernsehbildschirm, wonach die Menüanzeige ausgeblendet wird.
für Mikrofon Mikrofon gezogenen Mittenlinie aufgestellt? MULTI Anzeige
Mehr als 1,8 m Obere Grenzposition
des Mikrofons • Befindet sich das Mikrofon innerhalb 1 m ober- bzw.
CH LEVEL MENU
4 Prüfen Sie das an diesem Gerät ausgegebene mehrkanalige Digitalsignal.
unterhalb der Mittenlinie des Geräts? Die MULTI-Anzeige (siehe Seite 42 in der Bedienungsanleitung) leuchtet im Frontblendendisplay auf. Falls
• Ist das Mikrofon mindestens 1,8 m vom Gerät entfernt? auch Ton vom Fernseher selbst erzeugt wird, schalten Sie ihn stumm. Genauere Angaben zu digitalen Audio-
TV/AV
Bezüglich der Raumumgebung ENTER
YSP
Eingangssignalen finden Sie in der Bedienungsanleitung auf Seite 46.
• Herrscht im Hörraum die erforderliche Ruhe?
3 Drücken Sie STANDBY/ON auf TEST RETURN

4 Schalten Sie das Fernsehgerät ein.

der Fernbedienung. VOLUME CH TV VOL

Das Gerät wird dadurch eingeschaltet. 9 Bereiten Sie sich vor, den Raum zu verlassen. 5 Stellen Sie den Lautstärkepegel dieses Geräts mit VOLUME
Legen Sie zunächst Batterien in die Fernbedienung ein
(siehe Seite 26 in der Bedienungsanleitung).
Die bestmögliche Einstellung wird unter Umständen nicht
erzielt, wenn Sie im Hörraum bleiben. Bereiten Sie alles vor, 12 Trennen Sie das IntelliBeam-Mikrofon ab. +/– an der Fernbedienung ein.
Stellen Sie, sofern erforderlich, den Lautstärkepegel dieses so dass Sie den Hörraum nach Drücken von ENTER in Das AUTO SETUP ist hiermit beendet. Bewahren Sie das MUTE TV INPUT TV MUTE
Geräts ein.
Wenn ein Subwoofer angeschlossen ist, stellen Sie dessen
5 Wählen Sie den richtigen Schritt 10 innerhalb von 10 Sekunden verlassen können. IntelliBeam-Mikrofon an einem sicheren Platz auf.
Lautstärke und Übergangs-/Tiefpassfrequenz ein. Mehr dazu Die Einstellungen werden automatisch im Systemspeicher
finden Sie im Hinweis auf Seite 32 der Bedienungsanleitung.
Videoeingang am Fernsehgerät. y Tipp festgehalten.
Subwoofer (Tieftöner) „YSP-500“ erscheint auf dem Fernsehbildschirm. Wenn das • Nehmen Sie diese Anleitung beim Verlassen des Raums mit. 6 Drücken Sie eine der Schallstahlmodustasten an der Fernbedienung, 5BEAM ST+3BEAM 3BEAM

VOLUME CROSSOVER/
OSD-Video-Cinchkabel wie im Anschlussbeispiel an • Warten Sie draußen, bis der AUTO SETUP-Vorgang beendet ist. 1 2 3
STANDBY/ON POWER POWER
HIGH CUT
Videoeingang 1 des Fernsehgeräts angeschlossen wurde, • Das AUTO SETUP dauert etwa 3 Minuten. um den gewünschten Schallstrahlmodus zu wählen. STEREO MY BEAM MY SUR.

AV TV
wählen Sie den Videoeingang „1“. • Sie können den gestarteten AUTO SETUP-Vorgang durch 4 5 6
Wählen Sie den der sechst Schallstrahlmodi, der sich für die aktuelle Eingangsquelle am besten eignet.
einen Druck auf RETURN abbrechen.
Weitergehende Informationen zu den Schallstrahlmodi finden Sie in der Bedienungsanleitung auf Seite 44.
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON

MIN MAX MIN MAX

INTELLIBEAM MIC Zur manuellen Feinabstimmung der Hörumgebungsparameter oder zum Vornehmen weitergehender Einstellungen für
Lautsprecherpositionen, Schallstrahlen usw. lesen Sie auf Seite 56 der Bedienungsanleitung unter „MANUAL SETUP“ nach.

0906_YSP-500_De_guide.p65 2 9/6/07, 8:21 PM

 Artiklar som behövs för anslutningar och
manövrering
2 Anslutning av externa komponenter till ljudprojektorn
s Ljudkabel med stiftkontakter (x1)
s Videokabel med stiftkontakter (x1) Anslut externa komponenter, t.ex. en tv och en DVD-spelare, till ljudprojektor.
YSP-500 s Optisk kabel (x1)
s Digital ljudkabel med stiftkontakter (x1)
s IntelliBeam-mikrofon (x1)
s Mikrofonställ av hårdpapp (x1)
Använd lämpliga kablar till att ansluta tv:n och DVD-spelaren till ljudprojektorn enligt nedan. Anslut nätkabeln till ett nätuttag efter att alla övriga anslutningar är klara.
För vidare information om anslutning av andra komponenter hänvisas till sidorna 16 till 24 i bruksanvisningen.

s Demonstrations-DVD (x1)
SNABBREFERENSGUIDE I detta anslutningsexempel visas hur sådana externa komponenter som en tv och en DVD-spelare kan anslutas till ljudprojektorn med hjälp av medföljande kablar. Med denna anslutning kan flerkanaligt ljud från DVD-spelaren och analogt/digitalt ljud från tv:n återges.
Använd den videokabel med stiftkontakter som följer med DVD-spelaren till att utföra en videoanslutning mellan DVD-spelaren och tv:n.
I denna snabbreferensguide beskrivs hur man kan ansluta en tv och en DVD-spelare till ljudprojektorn och erhålla
surroundljudseffekter på ett snabbt och enkelt sätt. För närmare information om manövrering hänvisas till bruksanvisningen.
TV

1 Installering av ljudprojektorn
Anslut de medföljande kablar i följande ordning.
Bestäm var ljudprojektorn ska installeras. DVD-spelare
Installera ljudprojektorn på en plats där inga hinder, såsom möbler, är i vägen för ljudstrålarna. Sådana hinder kan medföra att 1 Ljudkabel med stiftkontakter
Videoanslutning
önskade surroundljudseffekter inte kan uppnås. Ljudprojektorn kan installeras längs en vägg eller i ett hörn. (för utmatning av analoga tv-ljudsignaler via ljudprojektorn)

2 Videokabel med stiftkontakter

Installera ljudprojektorn exakt på mitten av väggen, mätt från Installera ljudprojektorn i 40° till 50° vinkel från de
(för visning av menyn till YSP-500 på tv:n)
hörnen till vänster och höger. angränsande väggarna.
3 Optisk kabel
(för utmatning av digitala tv-ljudsignaler via ljudprojektorn)
Möbel etc. Möbel etc. ANALOG AUDIO VIDEO OPTICAL COAXIAL
OUTPUT INPUT AUDIO OUTPUT AUDIO OUTPUT 4 Digital ljudkabel med stiftkontakter
1. Ta bort dammskyddet Optisk kabel
L 1 (för utmatning av digitala DVD-ljudsignaler via
ljudprojektorn)
Vänster framkanal 40° till 50° Vänster framkanal Ta bort
R 2 dammskyddet och
Mittkanall Mittkanall
kontrollera att
2. Kontrollera riktningen kontakten är
Höger framkanal Höger framkanal
korrekt vänd, när
en kontakt på den
Anmärkning
Vänster surroundkanal Vänster surroundkanal
optiska kabeln ska Kontrollera huruvida digital ljudutmatning på tv:n och DVD-
Höger surroundkana Höger surroundkana anslutas. spelaren är inkopplat.

YSP-500
Installera ljudprojektorn i ett rack e.dyl. 1 2 3 4
Beroende på aktuell installationsmiljö kan anslutningar till externa komponenter (se “2 Anslutning av externa komponenter till ljudprojektorn”) utföras innan
ljudprojektorn installeras. Det rekommenderas att samtliga komponenter placeras ut temporärt på önskade platser för att det ska gå lättare att avgöra vilken L

åtgärd som behöver utföras först. R

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

COAXIAL CONNECTOR

För vidare information om installation hänvisas till sidan 13 i bruksanvisningen.

OPTICAL
AUDIO INPUT OUT DIGITAL INPUT

Nedan visas ett exempel på hur ljudprojektorn kan installeras i ett rack.

1 Placera ljudprojektorn 2 Anslut denna enhet tv:n 3 Installera ljudprojektorn i 4 Installationen är klar. Till ett nätuttag
framför racket. och DVD-spelaren. racket. L
Om en subwoofer är ansluten till denna enhet, slå av strömmen till
R subwoofern och utför därefter proceduren AUTO SETUP (se baksidan)

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

eller välj “SWFR” för “BASS OUT” i “SUBWOOFER SET” (se sid. 62 i
OPTICAL COAXIAL CONNECTOR bruksanvisningen).
AUDIO INPUT OUT DIGITAL INPUT
Anslut inte nätkabeln till ett
nätuttag förrän samtliga övriga
anslutningar är klara.

Systemanslutning

y Tips
Ljudanslutning
Placera ljudprojektorn på den övre hyllan, så att den hålls borta från golvet, för att uppnå bättra surroundeffekter. Utför åtgärderna på baksidan för att starta
Anmärkning AUTO SETUP-inställning, när externa Fortsättning
Var försiktig med att inte orsaka repor på ljudprojektorn eller racket. Subwoofer på baksidan
komponenter har anslutits.

Printed in Malaysia WM86580 [Sv] C2007 All rights reserved.

0906_YSP-500_Sv_guide.p65 1 9/6/07, 5:18 PM

 Fortsättning från framsidan

3 Utförande av AUTO SETUP-inställning (IntelliBeam) 6 Ställ manövreringslägesväljaren i 10 Tryck på ENTER för att starta 4 Återgivning av surroundljud
läget YSP. AUTO SETUP-inställningen och
Utför AUTO SETUP-inställningen för att anpassa inställningar till aktuell Manövreringsläget YSP kopplas in på ljudprojektorn.
lämna rummet inom 10 sekunder. Upplev digitalt surroundljud från tv eller DVD-skivor.
Angående manövrering av den tv eller den DVD-spelare som används hänvisas till bruksanvisningen till respektive komponent.
lyssningsmiljö. Följande meddelande visas på tv-skärmen. Lämna rummet
inom 10 sekunder, innan AUTO SETUP-inställningen startar.
IntelliBeam-tekniken gör det möjligt att uppnå optimala ljudinställningar i förhållande till den aktuella lyssningsmiljön. Det är normalt att höga testtoner matas
ut under pågående AUTO SETUP-inställning. Se till att inga barn finns i närheten av lyssningsrummet medan AUTO SETUP-inställningen genomförs. CH LEVEL MENU Återgivning av surroundljud från DVD-skivor Återgivning av surroundljud från tv
1 Anslut den medföljande IntelliBeam-mikrofonen till ingången ENTER
TV/AV
1 Välj videoingången för DVD- 1 Använd fjärrkontrollen som följer
YSP CH LEVEL MENU
AUTO SETUP START
INTELLIBEAM MIC på frontpanelen. TEST RETURN
Will begin in 10sec spelaren på tv:n. med tv:n till att välja önskad tv-
TV/AV Please leave the room
Det medföljande mikrofonstället av hårdpapp kan användas vid AUTO SETUP-inställning. Montera ihop stället och placera ENTER

IntelliBeam-mikrofonen ovanpå stället enligt illustrationen nedan. TEST

YSP
RETURN
**--------
[RETURN]:Cancel kanal.

1 2 3 4 7 Tryck in och håll AUTO SETUP Inställningsmenyerna ändras automatiskt under pågående
AUTO SETUP-inställning.Inställningsmenyerna ändras 2 Ställ manövreringslägesväljaren 2 Ställ manövreringslägesväljaren
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON intryckt i över 2 sekunder. automatiskt under pågående AUTO SETUP-inställning.
En meny visas på tv-skärmen. När AUTO SETUP-inställningen är klar visas följande meny på tv-skärmen. i läget YSP. i läget YSP.
INTELLIBEAM MIC
Om menyn inte visas, så kontrollera OSD-videokabeln med Manövreringsläget YSP kopplas in på ljudprojektorn. Manövreringsläget YSP kopplas in på ljudprojektorn.
stiftkontakter (se anslutningsexemplen på framsidan). SHOW RESULT
MEASUREMENT COMPLETE
IntelliBeam-mikrofon (medföljer) BEAM MODE :5 BEAM

TV
INPUT1
TV
INPUT2 MACRO AUTO SETUP
PREPARATION & CHECK
SUBWOOFER :NOT APPLICABLE
ENTER
TV/AV
ENTER
TV/AV
YSP YSP
Mikrofonställ av hårdpapp (medföljer) AUTO
Please connect the MIC.
[ENTER]:Save set-up
[RETURN]:Do not save set-up
VOL MODE SETUP INPUTMODE SLEEP
Please place the MIC at least TEST RETURN TEST RETURN
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.
5BEAM ST+3BEAM 3BEAM Measurement takes about 3min.
After [ENTER] is pressed, Om “ENVIRONMENT CHECK (FAILED)” visas, så läs
1 2 3 please leave the room.
[ENTER]:Start [RETURN]:Cancel anvisningarna på sidan 36 i bruksanvisningen och kör sedan
2 Placera IntelliBeam-mikrofonen på den normala lyssningsplatsen. inställningen igen.
3 1) Tryck på DVD på fjärrkontrollen 3 Tryck på TV på fjärrkontrollen till
Använd det medföljande mikrofonstället av hårdpapp eller ett stativ till att placera IntelliBeam-mikrofonen på samma höjd som
lyssnarens öronen är när lyssnaren sitter på lyssningsplatsen. 8 Kontrollera följande punkter. y Tips till ljudprojektorn. ljudprojektorn.
Angående IntelliBeam-mikrofonen • Resultet kan variera beroende på miljö. Återgivningsläget DVD kopplas in på ljudprojektorn. Återgivningsläget TV kopplas in på ljudprojektorn.
Placera IntelliBeam-mikrofonen längs • Är mikrofonen placerad längs en tänkt mittlinje dragen från • Om ett fel uppstår, så visas motsvarande felmeddelande på skärmen. Kontrollera i
en utdragen mittlinje från
ljudprojektorn? så fall orsaken till felet med hjälp av “Felmeddelanden för AUTO SETUP” på sidan STB VCR DVD AUX STB VCR DVD AUX
ljudprojektorn och på minst 1,8 meters 37 i bruksanvisningen och följ anvisningen för lämplig åtgärd. Tryck på RETURN för INPUT1
TV
INPUT2 MACRO TV

avstånd från ljudprojektorns framsida. • Är mikrofonen placerad inom en meter ovanför eller nedanför att starta om AUTO SETUP-inställningen. TV
INPUT1 INPUT2 MACRO
IntelliBeam- Övre gräns för TV
mikrofon
mikrofonens Se också till att den placeras inom en ljudprojektorns mitthöjd? AUTO
VOL MODE SETUP INPUTMODE SLEEP

meter ovanför eller nedanför

Ljudprojektorns
placering
ljudprojektorns mitthöjd.
• Är mikrofonen placerad över 1,8 meter från ljudprojektorns 2) Spela upp den medföljande 5BEAM ST+3BEAM 3BEAM

mitthöjd framsida? 1 2 3
Inom 1 m Angående rumsmiljön
11 Tryck på ENTER. demonstrations-DVD:n på DVD-spelaren.
• Är lyssningsrummet så tyst som möjligt?
Inom 1 m Följande meddelande visas i två sekunder på tv-skärmen
Mittlinje
Mikrofonställ av IntelliBeam- varefter menyvisningen avbryts.
hårdpapp Lyssningsplats Mikrofonställ
mikrofon
av Indikatorn MULTI
Över 1,8 m Nedre gräns för
mikrofonens placering
hårdpapp
9 Gör dig beredd att lämna rummet. CH LEVEL MENU
4 Kontrollera den flerkanaliga digitala signalen som matas ut via denna enhet.
Inställningsresultatet kan bli sämre, om någon befinner sig i AUTO SETUP COMPLETE Indikeringen MULTI (se sid. 42 i bruksanvisningen) visas på frontpanelens display. Om ljud återges via tv-
rummet. Var beredd att lämna rummet inom 10 sekunder TV/AV Please remove the MIC from högtalarna, så stäng av ljudet på tv:n. Vi hänvisar till sidan 46 i bruksanvisningen angående detaljer kring
the YSP and the listening
efter tryckning på ENTER i punkt 10. ENTER
YSP position. inmatning av digitala ljudsignaler.

3 Tryck på STANDBY/ON på TEST RETURN

4 Slå på strömmen till tv:n. y Tips

fjärrkontrollen. • Ta med denna guide ut ur rummet.

• Vänta utanför rummet tills AUTO SETUP-inställningen är klar. VOLUME CH TV VOL

Strömmen till ljudprojektorn slås på.

Sätt i batterier i fjärrkontrollen före manövrering (se sid.
• AUTO SETUP-inställningen tar cirka 3 minuter. 5 Tryck på VOLUME +/– på fjärrkontrollen för att reglera
• Tryck på RETURN för att vid behov avbryta en påbörjad AUTO
26 i bruksanvisningen). SETUP-inställning. 12 Koppla loss IntelliBeam-mikrofonen. volymnivån på ljudprojektorn.
Reglera vid behov volymnivån på ljudprojektorn.
AUTO SETUP-inställningen är därmed klar. Spara MUTE TV INPUT TV MUTE
Om en lågbashögtalare har anslutits, så ställ in volym
och övergångsfrekvens/övre gränsfrekvens. Vi hänvisar
5 Välj lämplig videoingång på tv:n. IntelliBeam-mikrofonen på ett säkert ställe.
“YSP-500” visas på tv-skärmen. Om OSD-videokabeln med Inställningarna sparas automatiskt i systemminnet.
till anmärkningarna på sidan 32 i bruksanvisningen.
stiftkontakter har anslutits till videoingång 1 på tv:n enligt
Subwoofer anslutningsexemplen, så se till att välja videoingång “1”. 6 Tryck på lämplig strållägesknapp på fjärrkontrollen för att 5BEAM ST+3BEAM 3BEAM

VOLUME CROSSOVER/ 1 2 3
STANDBY/ON POWER POWER
HIGH CUT
välja önskat strålläge. STEREO

4
MY BEAM

5
MY SUR.

6
AV TV
Välj det av de sex strållägena som passar bäst för aktuell ingångskälla på ljudprojektorn.
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON
För vidare information om strållägen hänvisas till sidan 44 i bruksanvisningen.
MIN MAX MIN MAX

INTELLIBEAM MIC Angående manuell finjustering av parametrarna för lyssningsmiljö samt avancerade inställningar för
högtalarpositioner, ljudstrålar m.m. hänvisas till “MANUAL SETUP” på sidan 56 i bruksanvisningen.

0906_YSP-500_Sv_guide.p65 2 9/6/07, 5:18 PM

 Items gebruikt voor de aansluitingen en te
verrichten handelingen
s Audio penstekkerkabel (x1)
2 Aansluiten van externe apparatuur op dit toestel
s Videokabel voor het in-beeld display (x1)
s Optische kabel (x1) Aansluiten van externe apparatuur, zoals een tv of DVD-speler, op dit toestel.
YSP-500 s Digitale audio penstekkerkabel (x1)
s IntelliBeam microfoon (x1)
s Kartonnen microfoonstandaard (x1)
s Demonstratie-DVD (x1)
Sluit uw tv of DVD-speler zoals hieronder aangegeven staat aan op dit toestel met behulp van de juiste kabels. Doe de stekker pas in het stopcontact wanneer u alle aansluitingen gemaakt heeft.
Zie de bladzijden 16 t/m 24 in de Handleiding voor meer informatie omtrent het aansluiten van andere apparatuur.

SNELGIDS Dit aansluitvoorbeeld laat u een manier zien om externe apparatuur, zoals een tv en een DVD-speler, aan te sluiten op dit toestel via de meegeleverde kabel. U kunt zo genieten van de multikanaals audio van uw DVD-speler en van de analoge/digitale audio van uw tv.
Gebruik de videokabel (pen-/tulpstekker) die werd meegeleverd met uw DVD-speler om een videoverbinding te maken tussen uw DVD-speler en uw tv.
Deze Snelgids legt stap voor stap uit hoe u uw tv en DVD-speler kunt aansluiten op dit toestel en snel en
makkelijk kunt gaan genieten van surroundweergave. Voor details verwijzen we u naar de Handleiding.
tv

1 Installeren van dit toestel

Sluit de meegeleverde kabels aan in deze volgorde.
Bepaal waar u dit toestel wilt installeren. DVD-speler
Installeer het toestel zo dat de geluidsbundels niet gehinderd worden door obstakels, zoals meubilair. Anders is het mogelijk 1 Audio penstekkerkabel
Videoverbinding
dat het surroundeffect tegenvalt. U kunt dit toestel parallel aan de wand of in een hoek installeren. (Voor weergave door dit toestel van de analoge
audiosignalen van de tv)
Installeer dit toestel exact in het midden van de wand, zoals Installeer dit toestel in de hoek, met een hoek van 40° tot 50°
2 Videokabel voor het in-beeld display
gemeten vanaf de linker en rechter hoek. ten opzichte van de beide wanden.
(Voor weergave van het YSP-500 menuscherm op de tv)

3 Optische kabel
Voorwerpen zoals meubelstukken Voorwerpen zoals meubelstukken ANALOG AUDIO VIDEO OPTICAL COAXIAL (Voor weergave door dit toestel van digitale audiosignalen van de tv)
OUTPUT INPUT AUDIO OUTPUT Optische kabel AUDIO OUTPUT
1. Trek het dopje eraf.
L 1 4 Digitale audio penstekkerkabel
(Voor weergave door dit toestel van de digitale audiosignalen van de DVD-speler)
Linker voorkanaal 40° t/m 50° Linker voorkanaal Haal het dopje van
R 2 de aansluiting voor
Middenkanaal Middenkanaal
u de optische
2. Controleer of het stekkertje de kabel gaat
Rechter voorkanaal Rechter voorkanaal
goede kant op zit. aansluiten en let
erop dat het
Opmerking
Linker surroundkanaal Linker surroundkanaal
stekkertje de Controleer of de digitale uitgangssignalen van uw tv en uw
Rechter surroundkanaal Rechter surroundkanaal goede kant op zit. DVD-speler inderdaad zijn ingeschakeld.

YSP-500
Installeer dit toestel in een rek of kast o.i.d.
Afhankelijk van de manier waarop u dit toestel wilt installeren, kunt u misschien het beste van tevoren de externe apparatuur erop aansluiten (zie “2 1 2 3 4
Aansluiten van externe apparatuur op dit toestel”). We raden u aan eerst alle betrokken apparatuur tijdelijk bij elkaar te brengen en aan te sluiten zodat u
gemakkelijker kunt beslissen wat u het eerst zult moeten doen. L

Zie bladzijde 13 in de Handleiding voor meer informatie over de installatie. R

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

OPTICAL COAXIAL CONNECTOR
AUDIO INPUT OUT DIGITAL INPUT

Hieronder volgt een voorbeeld waarin dit toestel in een rek of kast geplaatst wordt.

Naar het
1 Plaats het toestel voor de 2 Sluit dit toestel aan op uw 3 Plaats het toestel in de 4 De installatie is gereed.
stopcontact
kast. tv en op uw DVD-speler. kast. L
Als er een subwoofer is aangesloten op dit toestel, zet deze subwoofer
R dan aan en voer vervolgens de AUTO SETUP procedure uit (zie

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

achterzijde), of selecteer “SWFR” bij “BASS OUT” onder “SUBWOOFER
OPTICAL COAXIAL CONNECTOR SET” (zie bladzijde 62 in de Handleiding).
AUDIO INPUT OUT DIGITAL INPUT
Doe de stekker niet in het
stopcontact voordat alle
aansluitingen gemaakt zijn.

Systeemverbinding

y Tip
Audioverbinding
Voor een betere surroundweergave kunt u dit toestel het beste op de bovenste plank plaatsen, zodat het niet te dicht bij de vloer staat. Als u externe apparatuur heeft aangesloten,
Opmerking dient u de stappen aan de achterkant te volgen Zie
Wees voorzichtig dat er geen krassen komen op dit toestel of op het kastje of rek. Subwoofer ommezijde
om de AUTO SETUP procedure te starten.

Printed in Malaysia WM28880 [Nl] C2007 All rights reserved.

0906_YSP-500_Nl_guide.p65 1 9/6/07, 5:10 PM

 Vervolg van de voorzijde

3 Voer de AUTO SETUP uit (IntelliBeam) 6 Zet de schakelaar voor de bedieningsfunctie 10 Druk op ENTER om de AUTO SETUP 4 Genieten van surroundweergave
van de afstandsbediening op YSP. procedure te laten beginnen en verlaat
Voer de AUTO SETUP uit om de instellingen aan te passen aan uw kamer. Het toestel schakelt over naar de YSP bedieningsfunctie.
vervolgens binnen 10 seconden de kamer. Geniet van de digitale audio van uw tv of DVD in surroundweergave.
De IntelliBeam technologie stelt u in staat de vereiste geluidsinstellingen makkelijk aan te passen aan uw luisteromgeving. Het is normaal dat er tijdens de Raadpleeg de bijbehorende handleidingen voor instructies over hoe u uw tv of DVD-speler moet instellen of gebruiken.
Het volgende scherm zal op de tv verschijnen. U heeft 10
AUTO SETUP procedure luide testtonen geproduceerd worden. Zorg er daarom voor dat er zich geen kinderen in de luisterruimte bevinden wanneer de
seconden de tijd om de kamer te verlaten voordat de AUTO
AUTO SETUP procedure bezig is.
SETUP procedure begint.
CH LEVEL MENU Genieten van DVD’s met surroundweergave Genieten van uw tv met surroundweergave
1 Verbind de meegeleverde IntelliBeam microfoon met de INTELLIBEAM ENTER
TV/AV
1 Selecteer het ingangskanaal 1 Kies het gewenste tv-kanaal met
YSP CH LEVEL MENU

MIC aansluiting op het voorpaneel. TEST RETURN

voor de DVD-speler op uw tv. de afstandsbediening van uw tv.

TV/AV
U kunt de meegeleverde kartonnen microfoonstandaard gebruiken voor de AUTO SETUP. Zet de standaard in elkaar en plaats de ENTER
YSP
IntelliBeam microfoon er bovenop, zoals u hieronder kunt zien. TEST RETURN

1 2 3 4 7 Houd AUTO SETUP tenminste Het instelscherm verandert automatisch terwijl de AUTO
SETUP procedure bezig is. 2 Zet de schakelaar voor de bedieningsfunctie 2 Zet de schakelaar voor de bedieningsfunctie
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON 2 seconden ingedrukt. Wanneer de AUTO SETUP procedure klaar is, zal het
Het menuscherm verschijnt op de tv. volgende scherm op de tv verschijnen. van de afstandsbediening op YSP. van de afstandsbediening op YSP.
INTELLIBEAM MIC
Als het menuscherm niet verschijnt, dient u de videokabel Het toestel schakelt over naar de YSB bedieningsfunctie. Het toestel schakelt over naar de YSB bedieningsfunctie.
(pen/tulpstekker) voor het in-beeld display (OSD) te
controleren (zie het aansluitvoorbeeld op de eerste bladzijde).
IntelliBeam microfoon (meegeleverd)
TV TV/AV TV/AV
INPUT1 INPUT2 MACRO
ENTER ENTER
TV YSP YSP
Kartonnen microfoonstandaard (meegeleverd) AUTO
VOL MODE SETUP INPUTMODE SLEEP TEST RETURN TEST RETURN

5BEAM ST+3BEAM 3BEAM

Als de melding “ENVIRONMENT CHECK (FAILED)” op het
1 2 3
scherm verschijnt, raadpleeg dan bladzijde 36 van de
Handleiding en probeer de procedure vervolgens opnieuw.
2 Zet de IntelliBeam microfoon op uw normale luisterplek. y Tip
3 Druk op de afstandsbediening
U kunt de taal waarin de aanduidingen op het scherm
3 1) Druk op de afstandsbediening
Gebruik de meegeleverde kartonnen microfoonstandaard of een statief om de IntelliBeam microfoon op dezelfde hoogte als waar
normaal uw oren zouden zijn als u op uw favoriete plek zou zitten. verschijnen (OSD) selecteren via de onderstaande stappen.
Zet de schakelaar voor de bedieningsfunctie van de
y Tip van dit toestel op DVD. van dit toestel op TV.
• De resultaten zijn mede afhankelijk van de omgeving. Dit toestel schakelt over naar DVD weergave. Dit toestel schakelt over naar tv-weergave.
afstandsbediening op YSP. ➞ Druk op MENU. ➞ Druk op /
Plaats de IntelliBeam microfoon op • Als er iets mis gaat, zal de bijbehorende foutmelding op het scherm verschijnen.
, selecteer LANGUAGE SETUP. ➞ Druk op ENTER. ➞ Druk
een denkbeeldige lijn die recht door Raadpleeg in een dergelijk geval “Foutmeldingen voor de AUTO SETUP” op
op / om de gewenste taal te selecteren. ➞ Druk op STB VCR DVD AUX STB VCR DVD AUX
het midden van dit toestel loopt, op bladzijde 37 van de Handleiding en volg de instructies. Druk op RETURN om de TV TV
ENTER. INPUT1 INPUT2 MACRO INPUT1 INPUT2 MACRO
IntelliBeam minstens 1,8 m afstand van het AUTO SETUP procedure opnieuw op te starten. TV TV
microfoon Bovenste grens toestel. AUTO
VOL MODE SETUP INPUTMODE SLEEP

Zorg er ook voor dat de IntelliBeam

Hoogte van het
microfoonpositie
2) Speel de meegeleverde 5BEAM ST+3BEAM 3BEAM

midden van dit toestel

microfoon niet meer dan 1 m boven of
onder het midden van dit toestel
8 Controleer de volgende punten. 1 2 3

Binnen 1 m geplaatst wordt. Betreffende de IntelliBeam microfoon 11 Druk op ENTER. demonstratie-DVD op de DVD-speler.
• Is de microfoon geplaatst op de denkbeeldige lijn die precies
Binnen 1 m
Middenlijn Het volgende scherm zal 2 seconden lang getoond worden
Kartonnen door het midden van dit toestel loopt?
microfoonstandaard Luisterplek Kartonnen IntelliBeam op de tv, waarna het menuscherm van de tv zal verdwijnen.
microfoonstandaard microfoon • Is de microfoon niet meer dan 1 m boven of onder het midden MULTI indicator
Meer dan 1,8 m Ondergrens
microfoonpositie van dit toestel geplaatst? CH LEVEL MENU
4 Controleer de multikanaals digitale signalen die binnenkomen op dit toestel.
• Is de microfoon meer dan 1,8 m van de voorkant van dit De MULTI indicator (zie bladzijde 42 van de Handleiding) zal oplichten op het display op het voorpaneel. Als
toestel geplaatst? TV/AV
het ingangssignaal afkomstig is van uw tv, moet u misschien de geluidsweergave van uw tv uitschakelen
Betreffende de kamer ENTER
YSP
(“Mute”). Zie bladzijde 46 van de Handleiding voor meer informatie omtrent digitale audio ingangssignalen.
• Is de luisteromgeving (kamer) zo stil mogelijk?
3 Druk op de afstandsbediening TEST RETURN

4 Zet uw tv aan.
op STANDBY/ON. VOLUME CH TV VOL

Dit toestel gaat nu aan. 9 Tref voorbereidingen om de 5 Gebruik VOLUME +/– op de afstandsbediening om het volume
Doe voor u gaat beginnen eerst batterijen in de
afstandsbediening (zie bladzijde 26 in de Handleiding). kamer snel te kunnen verlaten. 12 Koppel de IntelliBeam microfoon los. van dit toestel te regelen.
Stel indien nodig het volume van dit toestel correct in.
Als u in de kamer blijft, zullen de instellingen mogelijk niet De AUTO SETUP procedure is nu klaar. Bewaar de MUTE TV INPUT TV MUTE
Als u een subwoofer heeft aangesloten, stel daarop dan
het volume en de crossover/hoge afsnijfrequentie in.
5 Selecteer het juiste videokanaal optimaal bepaald kunnen worden. Zorg ervoor dat u binnen IntelliBeam microfoon op een veilige plek.
10 seconden nadat u bij stap 10 op ENTER gedrukt heeft, De instellingen zijn automatisch opgeslagen in het
Raadpleeg de opmarking op bladzijde 32 in de Handleiding.
op uw tv. de kamer verlaten heeft. systeemgeheugen.
Subwoofer “YSP-500” zal op uw tv verschijnen. Als de videokabel
(pen/tulpstekker) voor het in-beeld display videosignaal
6 Druk op één van de functietoetsen voor de geluidsbundels op de afstandsbediening 5BEAM ST+3BEAM 3BEAM

VOLUME CROSSOVER/
y Tip 1 2 3
STANDBY/ON POWER POWER
HIGH CUT
(OSD) is aangesloten op video ingangsaansluiting 1 van
uw tv, zoals in het aansluitvoorbeeld, moet u dus
• Neem deze gids mee wanneer u de kamer verlaat. om de gewenste gebruiksfunctie voor de geluidsbundels te selecteren. STEREO

4
MY BEAM

5
MY SUR.

6
AV TV • Wacht buiten de kamer gedurende de AUTO SETUP proce-
overschakelen naar videokanaal “1”. Kies uit de zes mogelijke gebruiksfuncties voor de geluidsbundels de stand die u het best vindt passen bij het signaal en
dure.
de signaalbron waar u naar wilt luisteren. Zie bladzijde 44 van de Handleiding voor meer informatie over de gebruiksfuncties voor de geluidsbundels.
MIN MAX MIN MAX
• De AUTO SETUP procedure duurt ongeveer 3 minuten. INTELLIBEAM MIC INPUT VOLUME STANDBY/ON

• Druk op RETURN om de AUTO SETUP procedure te

annuleren nadat deze al is begonnen. INTELLIBEAM MIC Voor meer gedetailleerde aanpassingen met de hand aan uw luisteromgeving, of voor geavanceerde instellingen voor
luidsprekerposities, geluidsbundels enz., verwijzen we u naar “MANUAL SETUP” op bladzijde 56 van de Handleiding.

0906_YSP-500_Nl_guide.p65 2 9/6/07, 5:10 PM

 Аксессуаpы, используемые для
подключений и упpавления
s Аудиокабель (x1)
2 Подключение внешних компонентов к данному аппаpату
s Видеокабель для дисплея-на-экpане (x1)
s Оптический кабель (x1) Подключение внешних компонентов, как телевизоp или DVD-пpоигpыватель, к данному аппаpату.
YSP-500 s Цифpовой аудиокабель (x1)
s Микpофон IntelliBeam (x1)
s Каpтонная подставка для микpофона (x1)
s Демонстpационный DVD (x1)
С помощью соответствующих кабелей, подключите телевизоp или DVD-пpоигpыватель к данному аппаpату, как показано ниже. После завеpшения всех соединений, подключите силовой кабель к pозетке пеpеменного тока.
Подpобнее о подключении дpугих компонентов, смотpите стp. 16 – 24 в Инстpукции по эксплуатации.

КРАТКОЕ РУКОВОДСТВО В данном пpимеpе подключения отобpажен метод подключения внешних компонентов как телевизоp или DVD-пpоигpыватель к данному аппаpату с помощью поставляемого кабеля. Это позволит пpослушивать многоканальное звучание от DVD-пpоигpывателя и
аналоговое/цифpовое звучание от телевизоpа.
В данном кpатком pуководстве описываются пpоцедуpы подключения телевизоpа и DVD-пpоигpывателя к данному аппаpату и быстpое Для выполнения видеоподключения между DVD-пpоигpывателем и телевизоpом, используйте штыpьковый видеокабель, поставляемый вместе с DVD-пpоигpывателем.

и легкое достижение эффектов окpужающего звучания. Более подpобно об упpавлении, смотpите Инстpукцию по эксплуатации.
Телевизоp

1 Установка данного аппаpата

Подключите поставляемые кабели следующим обpазом.
Выбеpите место установки данного аппаpата. DVD-пpоигpыватель
Данный аппаpат должен устанавливаться в местах, где нет пpеп¤тствий, как мебель, стоящая на пути звуковых потоков. В ином случае, 1 Аудиокабель
Видеоподключение
невозможно будет достичь нужных эффектов окpужающего звучания. Данный аппаpат можно устанавливать паpаллельно стене или в углу. (Вывод аналоговых аудиосигналов телевизоpа чеpез данный аппаpат)

2 Видеокабель для дисплея-на-экpане

Установите данный аппаpат точно в центpе стены от Установите данный аппаpат в углу с углом 40° - 50° от
(Oтобpажение экpана меню YSP-500 на телевизоpе)
левого и пpавого углов. смежных стен.
3 Оптический кабель
(Вывод цифpовых аудиосигналов телевизоpа чеpез данный аппаpат)
Пpедмет, напpимеp, мебель Пpедмет, напpимеp, мебель ANALOG AUDIO VIDEO OPTICAL COAXIAL
OUTPUT INPUT AUDIO OUTPUT AUDIO OUTPUT 4 Цифpовой аудиокабель
1. Вытяните кpышку Оптический
L 1 (Вывод цифpовых аудиосигналов DVD чеpез данный аппаpат)
кабель

Фpонтальный левый канал 40° - 50° Фpонтальный левый канал Пеpед

R 2 подключением
Центpальный канал Центpальный канал
оптического
2. Пpовеpьте напpавление кабеля, вытяните
Фpонтальный пpавый канал Фpонтальный пpавый канал
кpышку, и затем
пpовеpьте
Пpимечание
Левый канал окpужающего звучания Левый канал окpужающего звучания
напpавления для Убедитесь, включена-ли функция вывода цифpовых
Пpавый канал окpужающего звучания Пpавый канал окpужающего звучания подключения аудиосигналов на телевизоpе и DVD-пpоигpывателе.
кабеля.

YSP-500
Установите данный аппаpат на подставке, дp. 1 2 3 4
В зависимости от сpеды установки, соединения с внешними компонентами (смотpите “2 Подключение внешних компонентов к данному аппаpату”)
можно выполнить до установки данного аппаpата. Рекомендуется вpеменно pазместить и подготовить все компоненты для того, чтобы pешить, L

какую пpоцедуpу нужно выполнить в пеpвую очеpедь. R

VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM

COAXIAL CONNECTOR

Подpобнее об установке, смотpите стp. 13 в Инстpукции по эксплуатации.

OPTICAL
AUDIO INPUT OUT DIGITAL INPUT

На следующем пpимеpе показан метод установки данного аппаpата внутpи подставки.

К pозетке
1 Поставьте данный 2 Подключите данный 3 Установите данный 4 Установка завеpшена.
пеpеменного тока
аппаpат пеpед подставкой. аппаpат к телевизоpу и аппаpат внутpи подставки. L Пpи подключении к данному аппаpату сабвуфеpа, включите
DVD-пpоигpывателю. питание сабвуфеpа, и затем выполните пpоцедуpу AUTO SETUP
R
(смотpите на обpатной стоpоне) или выбеpите “SWFR” для “BASS
VCR TV/STB SUBWOOFER VIDEO TV/STB AUX DVD SYSTEM
OUT” в “SUBWOOFER SET” (смотpите стp. 62 в Инстpукции по
OPTICAL COAXIAL CONNECTOR
Пока не завеpшены все
AUDIO INPUT OUT DIGITAL INPUT эксплуатации).
соединения, не подключайте
силовой кабель к pозетке
пеpеменного тока.

Системное соединение

y Совет
Аудиоподключение

Для достижения лучших эффектов окpужающего звучания, pазместите данный аппаpат на веpхней полке, на pасстоянии от пола. Если были подключены внешние компоненты,
Пpимечание следуя шагам на обpатной стоpоне, Пpодолжение на
Сабвуфеp обpатной стоpоне
Во избежание цаpапин на данном аппаpате или подставке, будьте внимательны. пpиступите к пpоцедуpе AUTO SETUP.

Printed in Malaysia WM28890 [Ru] C2007 All rights reserved.

0906_YSP-500_Ru_guide.p65 1 9/6/07, 9:06 PM

 Пpодолжение лицевой стоpоны

3 Выполните пpоцедуpу AUTO SETUP (IntelliBeam) 6 Установите селектоp pежима 10 Нажмите ENTER для запуска пpоцедуpы 4 Пpослушивание окpужающего звучания
упpавления на YSP. AUTO SETUP, и затем выйдите из
Для pегулиpовки настpоек, наилучшим обpазом подходящих для сpеды Данный аппаpат пеpеключается на pежим упpавления YSP.
комнаты в течение 10 секунд. Пpослушивание цифpового звучания от телевизоpа или DVD в pежиме окpужающего звучания.
Относительно инстpукций по упpавлению или настpойке телевизоpа или DVD-пpоигpывателя, смотpите инстpукцию по эксплуатации к каждому компоненту.
пpослушивания, выполните пpоцедуpу AUTO SETUP. На телевизоpе отобpажается следующий экpан.
Выйдите из комнаты в течение 10 секунд после запуска
íехнология IntelliBeam позволяет выполнить настpойки звучания, наилучшим обpазом подходящих для сpеды пpослушивания. Гpомкие тестовые тональнальные
пpоцедуpы AUTO SETUP.
сигналы во вpемя пpоцедуpы AUTO SETUP являются обычным явлением. Убедитесь, что во вpемя пpоцедуpы AUTO SETUP, в комнате для пpослушивания нет детей. CH LEVEL MENU Пpослушивание DVD в pежиме окpужающего звучания Пpослушивание телевизоpа в pежиме окpужающего
1 Подключите поставляемый микpофон IntelliBeam к гнезду ENTER
TV/AV
1 Выбеpите видеовход DVD на 1 С помощью пульта ДУ
YSP CH LEVEL MENU

INTELLIBEAM MIC на фpонтальной панели. TEST RETURN

телевизоpе. телевизоpа, выбеpите телеканал.

TV/AV
Для пpоцедуpы AUTO SETUP, можно воспользоваться поставляемую каpтонную стойку. Собеpите стойку и установите ENTER
YSP
микpофон IntelliBeam на ее повеpхности как показано ниже. TEST RETURN

1 2 3 4 7 Нажмите и удеpживайте AUTO Экpан настpойки автоматически пеpеключается во вpемя

пpоцедуpы AUTO SETUP. 2 Установите селектоp pежима 2 Установите селектоp pежима
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON SETUP более чем 2 секунды.
На телевизоpе отобpажается экpан меню. По завеpшению пpоцедуpы AUTO SETUP, на телевизоpе
отобpажается следующий экpан.
упpавления на YSP. упpавления на YSP.
INTELLIBEAM MIC
Если экpан меню не отобpажается, пpовеpьте Данный аппаpат пеpеключается на pежим упpавления YSP. Данный аппаpат пеpеключается на pежим упpавления YSP.
штыpьковый видеокабель дисплея-на-экpане (смотpите
пpимеp подключения на лицевой стоpоне).
Микpофон IntelliBeam (поставляется)
TV TV/AV TV/AV
INPUT1 INPUT2 MACRO
ENTER ENTER
TV YSP YSP
Каpтонная подставка для микpофона (поставляется) AUTO
VOL MODE SETUP INPUTMODE SLEEP TEST RETURN TEST RETURN

5BEAM ST+3BEAM 3BEAM

1 2 3 Пpи отобpажении “ENVIRONMENT CHECK (FAILED)”,

смотpите стp. 36 в Инстpукции по эксплуатации, и затем
2 Установите микpофон IntelliBeam на обычном месте пpослушивания. снова запустите пpоцедуpу.
y Совет 3 1) Нажмите DVD на пульте ДУ 3 Нажмите TV на пульте ДУ
С помощью поставляемой каpтонной стойки микpофона или тpеноги, установите микpофон IntelliBeam на высоте,
Следуя шагам ниже, можно выбpать язык, отобpажаемый на y Совет
одинаковой с высотой ваших ушей в сидячем положении.
дисплее-на-экpане. • В зависимости от сpеды, pезультат может отличаться.
данного аппаpата. данного аппаpата.
Установите селектоp pежима упpавления на YSP. ➞ • Пpи любой ошибке, на экpане отобpажается соответствующее Данный аппаpат пеpеключается на pежим воспpоизведения DVD. Данный аппаpат пеpеключается на pежим упpавления телевизоpом.
Установите микpофон IntelliBeam Нажмите кнопку MENU. ➞ Нажимая / , выбеpите сообщение об ошибке. В таком случае, смотpите “Сообщения
на вытянутой центpальной линии LANGUAGE SETUP. ➞ Нажмите кнопку ENTER. ➞ Нажимая об ошибках для AUTO SETUP” на стp. 37 в Инстpукции по STB VCR DVD AUX STB VCR DVD AUX
данного аппаpата, и на pасстоянии / , выбеpите нужный язык. ➞ Нажмите кнопку ENTER. эксплуатации, и затем следуйте инстpукциям. Для повтоpного INPUT1
TV
INPUT2 MACRO INPUT1
TV
INPUT2 MACRO
Микpофон 1,8 м или более от него. Также, TV TV
запуска пpоцедуpы AUTO SETUP, нажмите RETURN.
IntelliBeam Позиция веpхнего убедитесь, что микpофон AUTO
VOL MODE SETUP INPUTMODE SLEEP

IntelliBeam установлен в пpеделах 1

Высота центpа
пpедела микpофона
2) Воспpоизведите поставляемый
8 Пpовеpьте следующие пункты.
5BEAM ST+3BEAM 3BEAM
м выше или ниже высоты центpа
данного аппаpата 1 2 3
данного аппаpата.
В пpеделах 1 м О микpофоне IntelliBeam 11 Нажмите кнопку ENTER. демонстpационный DVD на DVD-пpоигpывателе.
• Установлен-ли микpофон на вообpажаемой центpальной На телевизоpе на 2 секунды отобpажается следующий
В пpеделах 1 м
Центpальная линия линии, пpоложенной от данного аппаpата?
Каpтонная подставка Место Микpофон экpан, и затем экpан меню на телевизоpе отключается.
для микpофона Каpтонная
пpослушивания подставка IntelliBeam • Установлен-ли микpофон в пpеделах 1 м выше или ниже Индикатоp MULTI
Более чем 1,8 м Позиция нижнего
пpедела микpофона
для
микpофона
высоты центpа данного аппаpата? CH LEVEL MENU
4 Пpовеpьте многоканальный цифpовой сигнал, выводимый на данный аппаpат.
• Установлен-ли микpофон на pасстоянии более чем 1,8 м На дисплее фpонтальной панели высвечивается индикатоp MULTI (смотpите стp. 42 в Инстpукции по
от фpонтальной стоpоны данного аппаpата? TV/AV
эксплуатации). Если звучание выводится от колонок телевизоpа, пpиглушите звучание на телевизоpе
О комнатной сpеде ENTER
YSP
Подpобнее о цифpовых входных аудиосигналах, смотpите стp. 46 в Инстpукции по эксплуатации.
• Соблюдается-ли пpедельная тишина в комнате для пpослушивания?
3 Нажмите STANDBY/ON на TEST RETURN

4 Включите питание телевизоpа.

пульте ДУ. VOLUME CH TV VOL

Пеpед упpавлением, вставьте в пульт ДУ батаpейки 9 Подготовьтесь выйти из комнаты. 5 Нажимая VOLUME+/– на пульте ДУ, настpойте уpовень
(смотpите стp. 26 в Инстpукции по эксплуатации).
Пpи необходимости, настpойте уpовень гpомкости
Если вы находитесь в комнате, выполнение наилучшей
настpойки может быть невозможным. Подготовьтесь
12 Отсоедините микpофон IntelliBeam. гpомкости данного аппаpата.
данного аппаpата. Пpоцедуpа AUTO SETUP завеpшена. Хpаните микpофон
выйти из комнаты в течение 10 секунд после нажатия MUTE TV INPUT TV MUTE
Пpи подключении сабвуфеpа, настpойте гpомкость и
частоту кpоссовеpа/сpеза высоких частот. Смотpите
5 Выбеpите соответствующий ENTER на шаге 10. IntelliBeam в безопасном месте. Настpойки
автоматически сохpаняются в памяти системы.
пpимечание на стp. 32 в Инстpукции по эксплуатации.
видеовход на телевизоpе. y Совет
Сабвуфеp На телевизоpе отобpажается “YSP-500”. Если
штыpьковый видеокабель дисплея-на-экpане
• Если вы выходите из комнаты, захватите данное 6 Нажав одну из кнопок pежима луча на пульте ДУ, 5BEAM ST+3BEAM 3BEAM

VOLUME CROSSOVER/ pуководство с собой. 1 2 3

STANDBY/ON POWER POWER
HIGH CUT
подключен к видеовходу 1 на телевизоpе, как
показано на пpимеpе подключения, пеpеключите
• Подождите вне комнаты во вpемя выполнения пpоцедуpы выбеpите нужный pежим луча. STEREO MY BEAM MY SUR.

AV TV AUTO SETUP. 4 5 6
видеовход на “1”. Выбеpите один из шести pежимов луча, наилучшим обpазом подходящий для текущего источника
• Пpоцедуpа AUTO SETUP анимает пpимеpно 3 минуты.
пpиема данного аппаpата. Подpобнее о pежимах луча, смотpите стp. 44 в Инстpукции по эксплуатации.
MIN MAX MIN MAX
• Для отмены пpоцедуpы AUTO SETUP после ее запуска, INTELLIBEAM MIC INPUT VOLUME STANDBY/ON

нажмите RETURN.
INTELLIBEAM MIC Относительно точной настpойки паpаметpов сpеды пpослушивания вpучную, или для выполнения дополнительных настpоек
pасположения колонок, звуковых лучей, дp., смотpите “MANUAL SETUP” на стp. 56 в Инстpукции по эксплуатации.

0906_YSP-500_Ru_guide.p65 2 9/6/07, 9:06 PM