JP-501S Carton Sealing Machine With Side Belts Driven With Stainless Steel Material Instructional Manual & Parts List PW-S535Ma 2005.04Instruction Manual Carton Sealing Machine (lwo Side Belts Driven) ‘Table of Contents Service Instruction Safety Provisions Specification Setup Procedure Description of Machine Description of Tapping Heads ‘Machine Installation “Tape Loading and Threading Adjustment “Tape Drum Friction Brake ‘The Applying Mochanism Spring ‘Box Drive Belts Maintenance Blade Replacement Replacing Box Drive Belts (Cleaning of The Machine Electrical Connection ‘Tape Application Leg Length ‘Troubleshooting ‘Replacement Parts and Parts List Page 23 72 89 ol 2 1314 1B B 4 15.17 1 15 16 16.17 1749 20-21 2Service Instruction: ‘To ourcustomers: ‘Thank you for your order of carton sealing machine, This machine has been well developed, set-up and tested by our engineering staff through long experiences and modem technologies in the factory before shipping to you, It can use most kinds of adhesive tap available in the world so that we believe this fs the finest automatic-tapping machine in the world. ‘We ask you to clean the machine regularly and to read the explanations in this instruction manual to prolong the life of the machine, any problems occur when operating this equipment, and you desire a service call or phone consultation. Please provide the customer support coordinator with the machine ‘model and serial number. Ifyou have a technical question that does not require an ‘immediate response, Replacement Parts ordered by machine model, part number, part name and quantity required,A. Safety Provisions ‘This Carton Sealing Machine is designed and manufactured in accordance with international safety standards, Provided safety guards for operator's protection must always be in place when operation machine, Stop the machine for tape roll replacement and ‘maintenance work. [AWARNING ‘The vo illustrated “Waring Sharp Knife” . labels, shown in Fig.1-1, are attached Sharp Knife to the cut-off blade guard on both tapping heads. The label warns the operator and service personnel ofthe very sharp {enife located behind the guard and to keep hhands out ofthis area except for tape loading - and/or serving the tapping heads. AWARNING Sharp Knife | J} Fig.1-1‘The “Warning Hazardous Voltage” labels, shown in Fig.1-2, is attached to the frame snext to the On/Off switch control box. The Iabel warns service personne! to unplug the power supply before attempting any service work on the machine. ‘The “Caution-Keep Hands Out of This Area” label, shown in Fig.1-3, is attached to the center plate atthe exit end of the bed frame. The label wams the operator to keep hands or clothes out ofthis area ‘when the drive belts are running. ' A WARNING in Hazardous Voltage Unplug Power Belore Servicing Fig.1-2 A CAUTION le Of This Area Fig.1-3 | Keep Hands out | I% Specification Working Environment: The machine should not be washed down or subject to conditions causing wet or damager. . Power Supply: Single phase,110/220V, S0/S0H2 ‘Tape Material: Self-Adhesive tapes, ‘Tape Width: 2.5 inches (36mm) and 3 inches (50mm) available. ‘Tape Roll Size: Inside Diameter Core-3 inches (76mm) Outside Diameter Core-11 inches (280mm) ‘Tape Width-2.5 inches or 3 inches ‘Tape Application Leg Length: 1) Standard: 60mm::Smm, 2) Optional; 70mm-+Smm or 9Smmé:Smm (by requested)7. Box Size: Standard size, L Ww H Min 150 120 85 ‘Max _ 300 500 8. Box Weight: The heaviest is 30 Kes. 9. Machine Dimensions: w L H At B c F ‘Min(mm)| = | 1405 | 370 | 410 = = axtam)| 970 | i200 | ams | sw | a | us | a] © In-feed/Out-feed conveyors are optional, Made by customer's requirement, 10. Machine Weight! Approximate 275 1bs(125 kgs) uncrated, Approximate 385 Ibs(17Skgs) crated, 11. Seating Speed: 20M/min,C. Set-up Procedure 1) Description of Machine2) Description of Tapping Heads Upper Tapping Head: —Tope Drum _Tope Adhesive Side Spring Tension Wrap Roller Applying Roller ale an rose Se vdLower Tapping Head: Buffing Roller Tawar) Led sari! Orange Blade Guard Applying Roller __— Threading Leader | Wrap Roller H— Knurled Roller Tension Wrap Roller Tope Adhesive Side One-Way Tension Roller Appiying Mechanism Sping Tope Roller Tope Drum 3) Machine Installation ‘The machine is equipped with adjustable legs that are located atthe comers ofthe fame: «) The fegs can be adjusted to obi different machine conveyor bed het from '550mm minimum to 810mm maximum. Refer to Fig.31 +) Post the carton and adjust both eft an right sie bet pulley. Refer Fig.3-2. ¢) Adjust the upper tapping head until the appropriate height so met the carton height. “Then adjust the pressure wheel until fasten the carton. |4d) Thread the tape into upper and lower tapping heads ) Check the voltage. ') Tum power switch “ON” to start the driven Bells and move the box forward. See Fig3-4.Fig3-3 4) Tape Loading and Threading The threading method for carton sealing size 605mm: 2) Upper Tapping Head: © ‘Stick the tape into tape drum. (Tape Adhesive Side Up) © Use the tape guiding plate, attached with the machine, to adhibit the tape, © Cut the extra tape from the middle of the tape drum,) Lower Tapping Head: © ‘Stick the tape into tape drum, (Tape Adhesive Side Down) © Use the tape guiding plate, attached withthe machine, to adhibit the tape. © Cut the extra tape from the middle ofthe tape drum. {Tope Adhesive Side O7,) Hope Adhesive Side Lower Tape Adhesive SideD. Adjustment. 1) Tape Drum Friction Brake: Shown in Fig, the tape drum fition brake on each tapping hea is pre-set for normal operation to prevent tape tll ravel. Should tension adjustment be requied, tum the kmaried nut onthe shaft to vay compression ofthe spring: ‘Tur knurled nut clocowise o increas te braking fore, and counterclockwise to decrease the braking force, Adjust to minimum tension that prevents excessive tape rollover travel. Fenaion Adsiment 2) The Applying Mechanism Spring: Shown in Fig 5-2 (ARB), contols spplying and buffing roller pressure onthe box and retums the mechanism to the reset position. “The spring pressure seting is for norm operation but i adjusteble, es shown in Fig $-2A. Removing the spring end loop frm the spring holder and placing Joop in other holes provided, as show inFig5-2B, will adjust the spring presse, The spring pressure should be sett the minimum possible while maintaining good tape application. 3sa Fig.5-2 3) Box Drive Belts: ‘The belt tension too tight results in the overload of motor. In this case, the ‘motor will be damaged easily. On contrast, the motor will antilock with the toosen belt tension. Take off the guard while adjusting the belt tension by tuming the screw.E. Maintenance “Turi off the electrical power supply and disconnect power cord froin electrical supply, before beginning maintenance. If electrical power is not disconnected, severe injury 10 personnel could result. Use care when replacing blades, as blade are extremely share, If care is not taken, severe injury to personnel could result 1) Blade Replacement aon : Refer othe Fig.6-1 and follow the steps. Loosen, but donot remove te blade screws (A). Remove and discard the old blade (mount the new blade with the beveled side away from the blade holder). Then, tighten the blade serews to secure the blade 2) Replacing Box Drive Belts Refer tothe Fig6-2 and follow he steps. Remove and retain center plat (A) and four screws, Loosen tension screw (B) by counterclockwise until all tensioi is retioved Then, removing the belt by taking out the splicing pi, Pee nerbele Giver pulleys ‘with laced splice at top Insert splicing pin, Pin must not extent beyond edge of bet ‘After that, reset the belt tension and make both sides equally. i 8 ~ A Oe sate Cover For Blode Blade Holder Fig.6-13) Cleaning of The Machine ‘To have the machine run smoothly, using the gear ofl #30 to moisture the moving spare parts once a week is necessary. Checking the blade without lots glue everyday 4) Electrical Connection Single Phase: 19 110V 19 220V 605 seif-stop “Optionel) tt ‘‘Three Phase: NESS Spiers) 30 220V eos 30 380V Toad Prepare By Customer ana F. Tape Application Leg Length “The standard size of sealing case is 605mm, and it ean change by requested. Before the adjustment, should tum off the machine and shut down the power supply in ease dangerous happened - Procedure: 1) Loosen, but do not remove, the two retaining serews that secure the upper tapping head. Shown in Fig-7-1A. Slide the head forward and life straight up to remove if from the case sealer 2) Life the lower tapping head, shown in Fig.7-IB, straight up to remove it ftom the ease sealer bed. L3) To rotate and set the shaft beneath 50 mm of the Tape Roller and ‘Tapping Head 50° the tape length will be 50mm. Show in Fig 7-2 4) Re-threaded the tape as shown in Fig.7-2 5) Put the Tapping Head back to the machine (the Tension Screw is loosen in the Upper Tapping Head) ©) Switch to “ON” and checking the carton length by seating carton again,—FEvNXOEKOE——_{_£_£__—_—_—_—— Shaft Spacer ~ oF 19 Fig.7-2G. Troubleshooting Review Set-Up Procedure Section so that the operational components ofthe machine are understood, The ‘troubleshooting lists some possible machine problems, causes and coretons. PROBLEM ‘CAUSE (CORRECTION 1. Driven Belts do not convey |1) Narow bores. [D Check machine specification. oxed Boxes are narow than commend essing lipage and premature ptt wear, [2) Worn drive bets by Replace dive belts 1) Upper tapping head doesnot) Adjust the box height laply enough pressure. ladjstment with the crank, |) Tapping head applying spring) Replace spring holder holder missing (5) Tapping head applying spring 5) Reduce spring pressure set too high 2, Drive Belts do not tur, 1) Deve bets tension is too low. |) Adjust bel fasion, 2) Blctial disconnect. Check power and electrical ve [) Motori not running. [) Evaluate problem and corest [3 Upper and lower tapping bead |1) Machine adjusted below 1) Set tapping heads to apply 50 interfere with eachother, jini, inches eg length la Deive Bele break 1) Worm I) Replace belt [2) Excessive belt tension a) Adjust belt tension, |S-Lightboxcs tp tack on ext) Upper si down too far) Cally aust upper (6. Boxes tip back on the taping |1) Upper ki down to fr 1) Carefully adjust upper ski Inds __ | 17. Tape move beckward i) One-way roller damage. |1) Replace one-way roller 8. The tape leg onthe font ofthe |1) The tape is incomecly threaded |!) The tape must go around ihe leases too long. [wap roller before going around hhc one-way tension role. 202) The tension ofthe ape is too f) Adjust the tension ofthe leg. | | by The ppbetween stp outed) No ap betwen spot fisd holder adi isto wide flr and sing pe ds dome orl) The desl or bas) Replace he ad lapeendisjngpdorselcd oben exh Tape son istolow. a) Lawsen hescewbyruning | | stiles, | [3) Adhesive has build up on the |) Clean and adjust the blade, j ae. li) Springiemissingorloose. |) Replace tighten sing 5) The poston aftpeis oo far_|5) Adj the Bade , Jo. "The ape eg onthe font ofthe) Knurled Wrap roll do not |!) Clean and moisture | lease isto short fn welt, | b) The postion of bad is oof. 2) Adj the lads } ) The tps is treadedincorrety, i | I) The tension ofthe pes too fs) Re-threaded. | j lien. |) Loose the srew by turning i 1) Catter spring are missing or anticlockwise Hoosen [sy Replace or tighten pings. "|i Tape dos ot aease onthe |1) Boxes do nat center tothe |1) Reposition the boxes. cater or boxe low symbol 2) The arow symbol isnot 2) Reposition the symbol sitioned probably. 12 Tape doesnot stick smoothly. |1) The tape rol of the tapping _|1) Clean the tape vol and ead does not ran wel, Inoisture. 2) The poston of upper tapping 2) Adjust the upper tapping heads, head is too high. 13. Tepe’shead of lower tpping_|1) Strap ou-feed holder too low. |) Adjust lice of strap out-feed head is upright down, holder and stmp out-feed holder, fo Bap. fens (¥. Squeaking noise ws machine i) Damage bat bearing 1) Replace the bes aH. Replacement Parts and Parts List It is suggested that the following spare parts be ordered and kept on hand: ey | __PasNO. Description ; 2 | C-50214-00 Roller-Applying 2 C-50505-00 Roller-Buffing 1 C-50403-00 Roller-Upper Extension 1 (C-50403-01 Roller- Lower Extension 2 (C-50311-00 Blade-? inches (50mm) 4 (€-50308-00 Spring-Cutter 2 C-50019-00 Drive Belt 22Tapping Head Assembly: Page No. 501 Frame Unit 23-24 502 Front Roller Assembly 25.26 503 Blade Unit 27-28 504 Link Assembly 29-30 505 Rear Roller Assembly 31-32 506 Tape Drum Assembly 33-34501 Frame Unit Ref. Parts No. ©-30101-00 (¢-50102-00 (€-50103-00 €-30105.00 50105-00 €-30106-01 c-50107-00 -50108-00 Description Frame Rear Upper rame-Front Upper CClamp-Spring Spacer-Upper Brush Shaft-Spacer Sew Ciller-Adjusting Tension HB M610 HSS M6r8 24 Qty__Remark 2502 Front Roller Assembly Ref.» PartsNo. Description T ©-50201-00 —Skaf- 0860 2 C-50202-00 Saf-Wrap Roller 3 €-50203-00 Roller-Top Tension 4 ©-$0204.00 Bearing FC-12 5 C50208-00 _ Roller-Weap 6 —€-50206-00 * Plate-Tepe 7 ©-50207-00 Applying Arm fi 8 C-30208-00 Applying Am #2 9 C-$0200.00 Plate-Tape 10 €-50210.00 Spring 11 C-50211-00 Spring-Compresion 12 C-50212.00 Wesher-Frction 13 C-50213-00 Shaft- 01060 14 €-5021400 Roller-Applying NM 15 C-50215-00 Bushing-Applying Roller 16 C-50216-00 Sha 868 17 C-50217-00 Spacer-Tape Plate 18 C-50218-00 Shaft 91068 19 C-50219-00 Spacer-Applying Arm 2 ©-50220.00Plate-Tape 21 ©-50221-00 _Roller-Wrap 2 C-50222.00 Plato-Tape 2 €-50223.00 _Roller-Knurled Assembly si TS-STW.0012 52 TS-HB.O6I2 53 TS-FMS.0508 4 TS-TMS-0406 55 TSEMSO6I2 sTWwMIZ HB M612 EMSMS*S TMS Mes FMS MerI2 NMS g Remark 56 _TS-H0N-0004 26503 Blade Unit Ref Parts No. 1 ©5030100 2 €-50302-00 3 ©50303-00 4 ©50304-00 5 ©-50305-00 6 — ©50306-00 7 ©50307-00 8 C50308-00 9 -50308-00 10 C-50310-00 1 50311-00 12 0312-00 13 650313-00 4 65031400 15 G-50315-00 16 C-50316-00 SL 788.0512 52 TSHB.0508 53 TSPW.0512 ‘54 ‘TS-HBS-0408 55 TS:PW-0408 Description Blade Guard Stop-Blade Assembly Spring-Blade Guard Frame-Rear Cut-Off Weldment Frame-Froat CatOfT Weldment Fixed Roller Spacer Spring-Cutter Shaf-Spacer Plvot-Cutter Lever Blade Guard Shaf-Blade Guard Plate Blade Sponge Plate Adjustable Plate (Let) Adjustable Pate (Right) EBMSTI2 EB MS" PWMs*12 EBS MAS PWwMaes 20 Oy Remark 56_TS-RMS.008_ FMS Ms504 Link Assembly504 Link Assembly eee ee Ref. Parts No. Deseription Qiy__ Remark 1 C-50401-00 Serew-Bearing Shoulder 2 ¢-80402-00 Serew Bushing-Bearing Shoulder 3 €-50403-00 Tension Spring-Lower Heading T 3-1 €-50403-01 Tension Spring-Upper Heading T €-50404-00 Adjustnent Slate-Teasion (€-50405-00 Front Link-Arm Bushing Asse {€.50406-00 Rear Link-Arm Bushing Ascerbl €-50407-00 | Cam-Tension {€-50408-00 Shaft 0868 (€-50409-00Shaft-Pivot 51 TS#B-0510_HBMS*10 4 30—— ns '505 Rear Roller Assembly Ref Paris No. Description Qty Remark, T ©-50501-00 Bushing Anm-Sub Assembly (Leh) 2 ©-30502.00 Bushing Arm-Sub Assembly (Right 3. C-50503-00 Shaft 210+90 4 C50S04-00 Shaft Bushing 5 C-50508-00 Roller-Buffing NM 6 1 8 C-50506-00 Bushing-Buffing Roller (C-50213-00 Shef-Bulfing Roller (€-50211-00 Spring 51 TS-MS.0612 FMS M6*12 4 JHB-0612_HBM6*12, 4 2506 Tape Drum Assembly Ref, ParisNo, ___Deseripti iy Remark T€-50601-06 2.-50602.00| 3.€.30603-00 4 50608.00| 5 €50605.00| 6 C-50606-00 7 €-50607-00 8 Cs0608-00 9 €-30609.00. 11 €30611-00 12.€-50612-00 51 HB0612 Bracket NoeM 1941 Shaf-Tape Drum 2" ‘Tape Drum Assembly Washer Friction Washer-Tension Spring “Tension Spring Ring Nut-Agjusting Iron Pate Detector for Nontape Supporter EBM6D 2 Option 2 Option 4 SQFSTSO508 _ STS (S52"* 9 4 aMachine Assembly 531 Upper Tapping Head Assembly 532 Frame Assembly 534 Column Assembly 535 Drive Assembly 536 Electronic Control Page No. 35-38 39-42 3-46 47-50 51-52531 Upper Tapping Head Assembly531 Upper Tapping Head Assembly 1 C53101-00 110. C-3101-10 1-20 C3101-20 1-30 65310130 2 ¢s3102-00 D1 C-53102-01 4 65310400 1 65310401 5 1209-00 7 ©53107-00 TL C53107-01 8 $P-0005.00 9 FAASIS.00 10 Cs1L10-00 13 C53113-00 18 C1118-00 19 C-33119-00 19-10 C-53119-10 19-20. C53119-20 19-30 C-53119.30 19-1 CS3I19-01 19-11 CS3119-11 19-21 C53119.21 19-31 C5311931 19-2 cs111902 20 FA-1829.00 21 cs1121-00 2 cs1122.00 2-1 CS112-01 22-2 _C-S1122-02 Bushing-Adjutable Bar Siding Upper Bracket Sting Upper Bracket (+1 seton) Sting Upper Bracke (+2 section) Siding Upper Bracket (+3 section) ‘Tapping Head Bracket (2°) Tapping Head Bracket (3") Roller Shaft (2) Rolle Shaft 3 Roller Front Cover (2") Front Cover 3") Door Magnetic rip ‘Tot Kits Washer Ring UpDown Mask Pressure Wheel Assembly Flag Adjustment Pressure Wheel Assembly Flag Adj (+1 see Presture Whos Assembly Flag Adj. (+2se¢ Pressure Wheel Assembly Flag Adj (+3 see Presure Wheel Flag Adjustment Pressure Whee Fag Ad. (+1 setion) Pese Whee Flag Ad (+2 scion) Pressure Wheel Rag Ad. (43 section) Adjustable Plate Knob Pressure Wheel Sin Pressure Wheel Assembly Shaft 36531 Upper Tapping Head Assembly531 Upper Tapping Head Assembly Ref,__ParisNo._Deseription Q'ty Remark: 51 TS-HBS.0855 52 Ts1mosi0 ‘TS-HBS.0608| TSSTH0015 TS-Tms-0008 TS-TMS.0310 TMSM3*10 TS-TMS-0%06 TMS Me's TSPWOI6 PWMBI6 ‘TSSW-0008 | SWME TSPW.O6I6 PWMSI6 ‘TS-Sw-0006 SWB TS-HBS.O6I0 HBS MSM16 TS-HN0008 ENMB ‘TS HN-0006 HN TS.HB0635 _ HB MSY a2escaeesnuss532 Frame Assembly Ref Parts No. ‘Description TC-54201-00 Machine Frame r 1-10 C-54201-10 Machine Frame (41 section) 1 1-20 C-54201-20 Machine Frame (+2 section) 1 1-30 ©-54201-30 Machine Frame (+3 section) 1 405420400 Leg 4 5§.6-54205.00 Clamp-Leg 4 7/€-54207-00 Suppor-Tapping Head (L) 1 35420800 Support: Tapping Head (R) 1 9.C-54209.00 BracketLeg 1 105120400 Casters Brake 1 12C4212.00 Roller-Long 10 12-10 C-$4212-10 —_Roller-Long (+1 section) 10 © ra20 5421220 RollerLang (+2 section) 10 12-30 €-54212-30 —Roller-Long (+3 section) 0 13.C54213-00 Roller Shaf-Long 0 13-10 C-54213-10 Roller Shaft-Long (+1 section) 10 13-20 C-54213-20 Roller Shafi-Long (+2secticn) 10 13-30 €54213-30 RollerSafeLong(+3 section) 10 nce acaee p Saas ene Moke es ocean ace poueccena ines i cence Macca cn face) ea eee F fi cca eae ee ane coma oe Ho | i 4532 Frame Assembly Ref Parts N Description Qiy_Remark 15 C54215-00 — Roller Shalt-Short (2°) 2 1510 C-S4215-10 Roller ShatShort(2")(41 section) 12 15-20 C-54215-20 Roller Shaft Short (27) (42 section) 12 15-30 C-54215-30 Roller Shaft Short (2") (43 section) 12 15-1 C.54215-01 Roller Shaf-Shor 3") 2 1-11 C-4215-11 Roller Shaf-Shor 3") (41 section) 12 1-21 C-54215-21 Roller Shalt Shoe 3") (+2.etion) 12 15-31 C-54215-31 Roller Shaft (9) (43 section) 12 15-4 CS4215-04 Roller Shaft-Shor (1 1/2") 2 15-16 C-54215-14 Roller Shaft Short (1 U2) (+ sectin 12 15-24 C.54215-24 Roller Shaft-Short (1 129) (42 sectic 12 15-34 C-54215-34 Roller Shae Short (1 U2)(43 section 12 16 €-5421600 Cep-Roller 4 17 C-54217-00 Fixed Plato-Roller Shaft 2 18 C-54218.00 Roller Bracket 1 19 €-54219.20 Roller Roller Bracket) 9 20 C-54220-00 Roller Shaft (Roller Bracket) 9 21 C54216-00 RollerPlastc Cover (Roller Bracket 18 2 CS1219-00 Shaft Plate Roller Bracket) 2 41 5425100. Serew a 42 €-54252-00 Roller-Tapping Head Bracket (2") 1 42-1 ©-54252-01 Rolle-Tapping Head Bracket 3") 1 St TS-TMs.o410 TMs Ma*10 16 52 TSHBS-0820 HBSM8*20 4 53 TSsw.0008 SWB 36 54 TSPWO8I6 PWMMrI6 36 55 TS-HBS-0830 HBS ME"30 8 56__TS-HN.0008_ NM m4 2534 Column Assembly534 Column Assembly Ref. PartsNo. ‘Description Qty “Remark “TGs1401-00 —ColamnVereal 2 110 C-S'401-19 Cofumn-Vertcal (+1 secticon) 2 1-20 €-51401-20 Column-Vertical (+2 seetioon) 2 2 G51402-00 Column (upedown) 2 3 CS1403-00 Shaft Bushing-Upper 2 4 65140400 Lead Screw 2 410 C51404-10 Lead Serew(+1 section) 2 4-20 C-51404-20 Lead Sorew (42 section) 2 6 5140600 Base-Spring 2 7 C$4407-00 —Column-torizontal 1 710 C-54407-10 Columan-Hforizomal (+1 section) 1 7-20 C-$4407-20 Colum Horizontel (+2 section) 1 730 C-54407:30 — Colume-Horizontal (+3 section) 1 8 C-51408-.00 Sprocket Sorew 38*18¢"139 1 1 1 1 1 2 2 2 2 4 4 4 8 8 2 2 9 C-S4409.00 Chain 3/864 10 C-51410.00 Roller 1 C51411-00 Knob 12 C51412.00 —Plate-Amm 13 C-51413.00 Spring-Compression 14 C-51414-00 Shield Spring 15 CSI415.00 Base-Spring 17 C-51417.00 Fixed Base-Lead Serew 18 C-51405.00 Guide Bar 18-10 C-51405-10 Guide Bar (+1 section) 16-20 C-51405-20 Guide Bar (42 section) 19 C1419-00 Guide Whee! 20 C-5142000 Shaft-Guide Whee! 21 C-51421-00 Upper Fixed Plate-Lead Screw (C-51422-00 Shaft Bushing-Lover 2 2365142300 Plug 6 “4534 Column Assembly Ref. ParisNo. Description Qi) Remark SL TS-HBS-OS10 BS S10 52 TSPwaSIs PWwse4 53 TS.H188-0608 HSS Mérs 5 5 TS-TMS.0508 Ts Ms*8_ 8 56 TS-HBS-0510 HBS Mse10 a 57 TS-SW-0006 SMG 8 38 TS-PMS.0610 FMS M610 1 59 TS-THS-0608 THS Movs » © TSHBS-0625 HBS M6r25 1 51 TSPW061s PWMer6 2 62 TS4HN0006 HN MG 10 6 TSETW.0 ETWEIO 2 64 TS.HBS.0820 as Mge20 8 6 TS Pw.o086 PwMErI6 8 2 66 _TS-PW.0616 PW Me —Srwosi6 PwMetIG535 Drive Assembly535 Drive Assembly Ref Parts No. ©33501-00 ©-53502-00 (©-53505-00 €-33506-00 (©-54507-00 €-54509-00 ©-54510-00 54510-01 c-s4510-02 1 C-s45011-00 M1 C-s45011-01 2 Cs4512.00 12-10 C54512-10, 12-20 ¢-54512-20 12-30 C-54513-30 1B Cs4513.00 110 C54513-10, 13-20 ©-54513-20 13-30, €54513-30 4 05451400 15 C.s4515.00 16 c-34516-00 17 cs411400 18 c-s4518-00 19 Cs411709 20 65452000 21 Cs4s21.00 2 C-54522.00 Be Cs4118.00 ‘Description Upper Plate-Drive Belt Lower Plate Drive Belt Cover-Let Cover Right Dive Shaftmain Drive Shaf-secondary Dive SupportRear Drive Shaf-Support Drive Hold Bracket Rear Drive Support-Front Drive Hold Bracket-Reat Lead Serew-Front Lead Serew-Front (+1 section) Lead Serew-Froat (+2 section) Lead Serev-Front (+3 section) Lead Serew-Rear “Lead Screw Rear (41 section) Lead Screw Rear (+2 section) Lead Sorew-Rear (43 seton) Needle Bearing SB/PEL-204 Sprocket-UR driven Chain 121391, Wheel-secondary Bushing-Iner ‘Shaft-Long Roller Shaf-Belt Cover Nut-Serew Nut-Tum Driven Belts 48 Remark 24 Cover: 1 4 _654824.00 Cover Amtwe'535 Drive Assembly535 Drive Assembly. Ref. Parts No. Description Q'ty _ Remark 25 C-$4525.00 AnmTum 26 C-54526-00 Handle-Turm 27 CS4112-00 Whocl-main Belt C-54115-00 Roller (€-54529-00 Beiring (UFL. 003) FA+1603-00 Bearing (620222) (C-51304-00 Gear Motor 1/110/60 €-51304-01 GearMotor 1220/50 C-51304-02 Gear Motor 1110/60 ©-51304-03 Gear Motor 1/220/60 C-51304-04 Gear Motor 3380 C-51304-05 Gear Motor 1/40/50 5130406 Gear Motor 3/380 ©-51304.07 Gear Motor 1/10/50 C-51304-08 Gear Motor 3220, 5130409 Gear Motor 3/220 31-10 C-51304-10 GearMotor 3/220 Bi-l1 C-51304-11 Gear Motor Brake incl. 32 C-54532-00 ShaftPlate 33 C-54533.00 ShatLower 34 C54127.00 Burhing 35. C-54128-00 Bushing BRe wens ween ne aewee SI TS-HBS.O616HBSM6*I6 0 52. TS-SW-0006 SWMs 2 53. TSPW.0616 PWMs"16 m St TS-HBS-1070 HBSMI0*70 6 55 TS-FMS.0820"M5M8*20 2 56_TS.HIB-0670_HB M6*70 4 me