GB Belt Sander Instruction manual

ID Mesin Ampelas Sabuk Petunjuk penggunaan

VI Máy chà nhám b ng Tài li u h ng d n

TH

9031
 1

3
2 4

1 001282 2 001284

3 001285 4 001286

9 11
10
8

9 12

5 001287 6 001288

10 9

14
13

7 001289 8 001145

2
 15
16

9 001290

3
ENGLISH
Explanation of general view
1. Lock button 7. Arrow 13. Dust collector
2. Switch trigger 8. Nozzle cap 14. Limit mark
3. Side grip 9. Nozzle 15. Brush holder cap
4. Grip holder 10. Hose 19 16. Screwdriver
5. Rear pulley 11. Hose of vacuum cleaner
6. Front pulley 12. Vacuum cleaner

SPECIFICATIONS
Model 9031
Belt size 30 mm x 533 mm
Belt speed 3.3 - 16.6m/s (200 - 1,000 m/min)
Overall length 380 mm
Net weight 2.1 kg
Safety class /II
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END201-6
Save all warnings and
Symbols
The following show the symbols used for the equipment. instructions for future reference.
Be sure that you understand their meaning before use.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
.... Read instruction manual. (cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or dark
.............. DOUBLE INSULATION areas invite accidents.
2. Do not operate power tools in explosive
ENE052-1 atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
Intended use create sparks which may ignite the dust or fumes.
The tool is intended for the sanding of large surface of 3. Keep children and bystanders away while
wood, plastic and metal materials as well as painted operating a power tool. Distractions can cause you
surfaces. to lose control.
ENF002-2 Electrical safety
Power supply 4. Power tool plugs must match the outlet. Never
The tool should be connected only to a power supply of modify the plug in any way. Do not use any
the same voltage as indicated on the nameplate, and can adapter plugs with earthed (grounded) power
only be operated on single-phase AC supply. They are tools. Unmodified plugs and matching outlets will
double-insulated and can, therefore, also be used from reduce risk of electric shock.
sockets without earth wire. 5. Avoid body contact with earthed or grounded
GEA005-3 surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
General Power Tool Safety shock if your body is earthed or grounded.
Warnings 6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
WARNING Read all safety warnings and all the risk of electric shock.
instructions. Failure to follow the warnings and 7. Do not abuse the cord. Never use the cord for
instructions may result in electric shock, fire and/or carrying, pulling or unplugging the power tool.
serious injury. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.

4
8. When operating a power tool outdoors, use an power tool. Power tools are dangerous in the hands
extension cord suitable for outdoor use. Use of a of untrained users.
cord suitable for outdoor use reduces the risk of 22. Maintain power tools. Check for misalignment or
electric shock. binding of moving parts, breakage of parts and
9. If operating a power tool in a damp location is any other condition that may affect the power
unavoidable, use a residual current device (RCD) tool’s operation. If damaged, have the power tool
protected supply. Use of an RCD reduces the risk of repaired before use. Many accidents are caused by
electric shock. poorly maintained power tools.
10. Use of power supply via a RCD with a rated 23. Keep cutting tools sharp and clean. Properly
residual current of 30mA or less is always maintained cutting tools with sharp cutting edges are
recommended. less likely to bind and are easier to control.
24. Use the power tool, accessories and tool bits etc.
Personal safety
in accordance with these instructions, taking into
11. Stay alert, watch what you are doing and use
account the working conditions and the work to
common sense when operating a power tool. Do
be performed. Use of the power tool for operations
not use a power tool while you are tired or under
different from those intended could result in a
the influence of drugs, alcohol or medication. A
hazardous situation.
moment of inattention while operating power tools
may result in serious personal injury. Service
12. Use personal protective equipment. Always wear 25. Have your power tool serviced by a qualified
eye protection. Protective equipment such as dust repair person using only identical replacement
mask, non-skid safety shoes, hard hat, or hearing parts. This will ensure that the safety of the power tool
protection used for appropriate conditions will reduce is maintained.
personal injuries. 26. Follow instruction for lubricating and changing
13. Prevent unintentional starting. Ensure the switch accessories.
is in the off-position before connecting to power 27. Keep handles dry, clean and free from oil and
source and/or battery pack, picking up or carrying grease.
the tool. Carrying power tools with your finger on the
GEB015-3
switch or energising power tools that have the switch
on invites accidents. BELT SANDER SAFETY
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
WARNINGS
attached to a rotating part of the power tool may result 1. Hold power tool by insulated gripping surfaces,
in personal injury. because the belt may contact its own cord. Cutting
15. Do not overreach. Keep proper footing and a “live” wire may make exposed metal parts of the
balance at all times. This enables better control of power tool “live” and could give the operator an
the power tool in unexpected situations. electric shock.
16. Dress properly. Do not wear loose clothing or 2. Ventilate your work area adequately when you
jewellery. Keep your hair, clothing, and gloves perform sanding operations.
away from moving parts. Loose clothes, jewellery or 3. Some material contains chemicals which may be
long hair can be caught in moving parts. toxic. Take caution to prevent dust inhalation and
17. If devices are provided for the connection of dust skin contact. Follow material supplier safety data.
extraction and collection facilities, ensure these 4. Always use the correct dust mask/respirator for
are connected and properly used. Use of dust the material and application you are working with.
collection can reduce dust-related hazards. 5. Always use safety glasses or goggles. Ordinary
Power tool use and care eye or sun glasses are NOT safety glasses.
18. Do not force the power tool. Use the correct power 6. Hold the tool firmly with both hands.
tool for your application. The correct power tool will 7. Make sure the belt is not contacting the workpiece
do the job better and safer at the rate for which it was before the switch is turned on.
designed. 8. Keep hands away from rotating parts.
19. Do not use the power tool if the switch does not 9. Do not leave the tool running. Operate the tool
turn it on and off. Any power tool that cannot be only when hand-held.
controlled with the switch is dangerous and must be 10. This tool has not been waterproofed, so do not
repaired. use water on the workpiece surface.
20. Disconnect the plug from the power source and/or
the battery pack from the power tool before SAVE THESE INSTRUCTIONS.
making any adjustments, changing accessories,
or storing power tools. Such preventive safety WARNING:
measures reduce the risk of starting the power tool DO NOT let comfort or familiarity with product (gained
accidentally. from repeated use) replace strict adherence to safety
21. Store idle power tools out of the reach of children rules for the subject product. MISUSE or failure to
and do not allow persons unfamiliar with the follow the safety rules stated in this instruction
power tool or these instructions to operate the manual may cause serious personal injury.

5
FUNCTIONAL DESCRIPTION When connecting to Makita vacuum cleaner, an optional
hose 28 mm in inner diameter is necessary. (Fig. 6)
CAUTION: When connecting to Makita dust collector (Model 420S),
• Always be sure that the tool is switched off and the hose of the dust collector is not necessary. You can
unplugged before adjusting or checking function on the connect the belt sander directly to the optional hose 28.
tool. (Fig. 7)

Switch action (Fig. 1) OPERATION

CAUTION:
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the • Secure the workpiece with clamps, etc. if there is any
possibility of it moving during the work operations.
“OFF” position when released.
• The tool should not already be in contact with the
To start the tool, simply pull the switch trigger. Release the
switch trigger to stop. workpiece surface when you turn the tool on or off.
Otherwise a poor sanding finish, damage to the belt or
For continuous operation, pull the switch trigger, push in
the lock button and then release the switch trigger. loss of control of the tool may result.
• When working with the tool, be very careful to avoid
To stop the tool from the locked position, pull the switch
any contact of the tool and belt with any part of your
trigger fully, and then release it.
body or anyone or anything near you.
Speed adjusting dial Always use the side grip (auxiliary handle) and firmly hold
the tool by both side grip and switch handle during
The belt speed can be infinitely adjusted between 3.3 m
and 16.6 m per second by turning the speed adjusting dial operations. Turn the tool on and wait until it attains full
speed. Gently apply the tool to the workpiece surface and
to a given number setting from 1 to 6.
move the tool forward and back. Press the belt only lightly
Higher speed is obtained when the dial is turned in the
direction of number 6, lower speed is obtained when it is on the workpiece. Excessive pressure may damage the
belt and shorten tool life.
turned in the direction of number 1. Select the proper
speed for the workpiece to be sanded.
CAUTION:
MAINTENANCE
• The speed adjusting dial can be turned only as far as 6 CAUTION:
and back to 1. Do not force it past 6 or 1, or the speed • Always be sure that the tool is switched off and
adjusting function may no longer work. unplugged before attempting to perform inspection or
maintenance.
ASSEMBLY • Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
CAUTION:
• Always be sure that the tool is switched off and Replacing carbon brushes
unplugged before carrying out any work on the tool. Remove and check the carbon brushes regularly. Replace
them when they are worn down to the limit mark. Keep the
Installing side grip (Fig. 2) carbon brushes clean and free to slip in the holders. Both
For your own safety, always use the side grip. Install it by carbon brushes should be replaced at the same time. Use
screwing it firmly on the grip holder. The side grip can be only identical carbon brushes. (Fig. 8)
pivoted for easy operation. Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
Installing or removing abrasive belt secure the brush holder caps. (Fig. 9)
(Fig. 3) To maintain product SAFETY and RELIABILITY, repairs,
Loop the belt over the front pulley. Hold the tool as shown any other maintenance or adjustment should be
in the figure and press down to retract the front pulley so performed by Makita Authorized Service Centers, always
that you can slip the other end of the belt over the rear using Makita replacement parts.
pulley. When pressing down the tool, be careful not to
allow the front pulley to turn unexpectedly, causing you to OPTIONAL ACCESSORIES
lose control of the tool.
CAUTION:
NOTE:
• These accessories or attachments are recommended
• The arrow on the inside of the belt and that marked on
for use with your Makita tool specified in this manual.
the rear pulley must point in the same direction. (Fig. 4)
The use of any other accessories or attachments might
Connecting to Makita vacuum cleaner present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
CAUTION: If you need any assistance for more details regarding
• Always close the nozzle cap when the vacuum cleaner these accessories, ask your local Makita Service Center.
is not connected to the nozzle. Never insert your finger • Abrasive belts
into the nozzle. (Fig. 5) • Hose 28
Cleaner sanding operations can be performed by
connecting the belt sander to Makita vacuum cleaner.
6
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.

7
BAHASA INDONESIA
Penjelasan tampilan keseluruhan
1. Tombol kunci 7. Tanda panah 13. Pengumpul debu
2. Saklar pemicu 8. Tutup nosel 14. Tanda batas
3. Gagang sisi 9. Nosel 15. Tutup tempat sikat
4. Tempat gagang 10. Selang 19 16. Obeng
5. Puli belakang 11. Selang pengisap debu
6. Puli depan 12. Pengisap debu

SPESIFIKASI
Model 9031
Ukuran sabuk 30 mm x 533 mm
Kecepatan sabuk 3,3 - 16,6m/detik (200 - 1.000 m/menit)
Panjang keseluruhan 380 mm
Berat bersih 2,1 kg
Kelas keamanan /II
• Karena kesinambungan program penelitian dan pengembangan kami, spesifikasi yang disebutkan di sini dapat
berubah tanpa pemberitahuan.
• Spesifikasi dapat berbeda dari satu negara ke negara lainnya.
• Berat menurut Prosedur EPTA 01/2003
END201-6
Simpanlah semua peringatan dan
Simbol
Berikut ini adalah simbol-simbol yang digunakan pada petunjuk untuk acuan di masa
peralatan ini. depan.
Pastikan Anda mengerti makna masing-masing simbol
sebelum menggunakan alat. Istilah “mesin listrik” dalam semua peringatan mengacu
pada mesin listrik yang dijalankan dengan sumber listrik
..... Baca petunjuk penggunaan. jala-jala (berkabel) atau baterai (tanpa kabel).
Keselamatan tempat kerja
1. Jaga tempat kerja selalu bersih dan
.............. ISOLASI GANDA berpenerangan cukup. Tempat kerja yang
berantakan dan gelap mengundang kecelakaan.
ENE052-1 2. Jangan gunakan mesin listrik dalam lingkungan
Penggunaan yang mudah meledak, misalnya jika ada cairan,
Mesin ini digunakan untuk mengampelas permukaan gas, atau debu yang mudah menyala. Mesin listrik
yang luas pada bahan kayu, plastik dan.logam serta menimbulkan bunga api yang dapat menyalakan debu
permukaan yang dicat. atau uap tersebut.
3. Jauhkan anak-anak dan orang lain saat
ENF002-2 menggunakan mesin listrik. Bila perhatian terpecah,
Pasokan daya anda dapat kehilangan kendali.
Mesin harus terhubung dengan pasokan daya listrik yang
bervoltase sama dengan yang tertera pada pelat nama, Keamanan kelistrikan
dan hanya dapat dijalankan dengan listrik AC fase 4. Steker mesin listrik harus cocok dengan
tunggal. Mesin diisolasi ganda dan oleh sebab itu dapat stopkontak. Jangan sekali-kali mengubah steker
dihubungkan dengan soket tanpa arde. dengan cara apa pun. Jangan menggunakan
steker adaptor dengan mesin listrik berarde
GEA005-3 (dibumikan). Steker yang tidak diubah dan
Peringatan Keselamatan Umum stopkontak yang cocok akan mengurangi risiko
sengatan listrik.
Mesin Listrik 5. Hindari sentuhan tubuh dengan permukaan
berarde atau yang dibumikan seperti pipa,
PERINGATAN Bacalah semua peringatan
radiator, kompor, dan kulkas. Risiko sengatan listrik
keselamatan dan semua petunjuk. Kelalaian mematuhi
bertambah jika tubuh Anda terbumikan atau terarde.
peringatan dan petunjuk dapat menyebabkan sengatan
6. Jangan membiarkan mesin listrik kehujanan atau
listrik, kebakaran dan/atau cedera serius.
kebasahan. Air yang masuk ke dalam mesin listrik
akan meningkatkan risiko sengatan listrik.

8
7. Jangan menyalahgunakan kabel. Jangan sekali- Penggunaan dan pemeliharaan mesin listrik
kali menggunakan kabel untuk membawa, 18. Jangan memaksa mesin listrik. Gunakan mesin
menarik, atau mencabut mesin listrik dari listrik yang tepat untuk keperluan Anda. Mesin
stopkontak. Jauhkan kabel dari panas, minyak, listrik yang tepat akan menuntaskan pekerjaan
tepian tajam, atau bagian yang bergerak. Kabel dengan lebih baik dan aman pada kecepatan sesuai
yang rusak atau kusut memperbesar risiko sengatan rancangannya.
listrik. 19. Jangan gunakan mesin listrik jika sakelar tidak
8. Bila menggunakan mesin listrik di luar ruangan, dapat menyalakan dan mematikannya. Mesin listrik
gunakan kabel ekstensi yang sesuai untuk yang tidak dapat dikendalikan dengan sakelarnya
penggunaan di luar ruangan. Penggunaan kabel adalah berbahaya dan harus diperbaiki.
yang sesuai untuk penggunaan luar ruangan 20. Cabut steker dari sumber listrik dan/atau baterai
mengurangi risiko sengatan listrik. dari mesin listrik sebelum melakukan penyetelan,
9. Jika mengoperasikan mesin listrik di lokasi penggantian aksesori, atau menyimpan mesin
lembap tidak terhindarkan, gunakan pasokan daya listrik. Langkah keselamatan preventif tersebut
yang dilindungi peranti imbasan arus (residual mengurangi risiko hidupnya mesin secara tak
current device - RCD). Penggunaan RCD sengaja.
mengurangi risiko sengatan listrik. 21. Simpan mesin listrik jauh dari jangkauan anak-
10. Penggunaan pasokan daya melalui RCD dengan anak dan jangan biarkan orang yang tidak paham
kapasitas arus sisa 30 mA atau kurang selalu mengenai mesin listrik tersebut atau petunjuk ini
dianjurkan. menggunakan mesin listrik. Mesin listrik sangat
berbahaya di tangan pengguna yang tak terlatih.
Keselamatan diri
22. Rawatlah mesin listrik. Periksa apakah ada bagian
11. Jaga kewaspadaan, perhatikan pekerjaan Anda
bergerak yang tidak lurus atau macet, bagian yang
dan gunakan akal sehat bila menggunakan mesin
pecah dan kondisi lain yang dapat mempengaruhi
listrik. Jangan menggunakan mesin listrik saat
penggunaan mesin listrik. Jika rusak, perbaiki
Anda lelah atau di bawah pengaruh obat bius,
dahulu mesin listrik sebelum digunakan. Banyak
alkohol, atau obat. Sekejap saja lalai saat
kecelakaan disebabkan oleh kurangnya pemeliharaan
menggunakan mesin listrik dapat menyebabkan
mesin listrik.
cedera diri yang serius.
23. Jaga agar mesin pemotong tetap tajam dan bersih.
12. Gunakan alat pelindung diri. Selalu gunakan
Mesin pemotong yang terawat baik dengan mata
pelindung mata. Peralatan pelindung seperti masker
pemotong yang tajam tidak mudah macet dan lebih
debu, sepatu pengaman anti-selip, helm pengaman,
mudah dikendalikan.
atau pelindung telinga yang digunakan untuk kondisi
24. Gunakan mesin listrik, aksesori, dan mata mesin,
yang sesuai akan mengurangi risiko cedera diri.
dll. sesuai dengan petunjuk ini, dengan
13. Cegah penyalaan yang tidak disengaja. Pastikan
memperhitungkan kondisi kerja dan jenis
bahwa sakelar berada dalam posisi mati (off)
pekerjaan yang dilakukan. Penggunaan mesin listrik
sebelum menghubungkan mesin ke sumber daya
untuk penggunaan yang lain dari peruntukan dapat
dan/atau baterai, atau mengangkat atau
menimbulkan situasi berbahaya.
membawanya. Membawa mesin listrik dengan jari
Anda pada sakelarnya atau mengalirkan listrik pada Servis
mesin listrik yang sakelarnya hidup (on) akan 25. Berikan mesin listrik untuk diperbaiki hanya
mengundang kecelakaan. kepada oleh teknisi yang berkualifikasi dengan
14. Lepaskan kunci-kunci penyetel sebelum menggunakan hanya suku cadang pengganti yang
menghidupkan mesin listrik. Kunci-kunci yang serupa. Hal ini akan menjamin terjaganya keamanan
masih terpasang pada bagian mesin listrik yang mesin listrik.
berputar dapat menyebabkan cedera. 26. Patuhi petunjuk pelumasan dan penggantian
15. Jangan meraih terlalu jauh. Jagalah pijakan dan aksesori.
keseimbangan sepanjang waktu. Hal ini 27. Jagalah agar gagang kering, bersih, dan bebas
memungkinkan kendali yang lebih baik atas mesin dari minyak dan gemuk.
listrik dalam situasi yang tidak diharapkan.
GEB015-3
16. Kenakan pakaian dengan baik. Jangan memakai
pakaian yang kedodoran atau perhiasan. Jaga PERINGATAN KESELAMATAN
jarak antara rambut, pakaian, dan sarung tangan
Anda dengan bagian mesin yang bergerak.
MESIN AMPELAS SABUK
Pakaian kedodoran, perhiasan, atau rambut panjang 1. Pegang mesin listrik pada permukaan genggam
dapat tersangkut pada bagian yang bergerak. yang terisolasi, karena sabuk mungkin
17. Jika tersedia fasilitas untuk menghisap dan bersentuhan dengan kawat tersembunyi.
mengumpulkan debu, pastikan fasilitas tersebut Memotong kawat “hidup” dapat menyebabkan bagian
terhubung listrik dan digunakan dengan baik. logam pada mesin teraliri arus listrik dan menyengat
Penggunaan pembersih debu dapat mengurangi pengguna.
bahaya yang terkait dengan debu. 2. Beri ruang udara secukupnya ketika Anda
melakukan pekerjaan pengampelasan.

9
3. Bahan tertentu mengandung zat kimia yang PERAKITAN
mungkin beracun. Hindari menghirup debu dan
persentuhan dengan kulit. Ikuti data keselamatan PERHATIAN:
bahan dari pemasok. • Selalu pastikan bahwa mesin dalam keadaan mati dan
4. Selalu gunakan masker debu/alat pernafasan yang steker tercabut sebelum melakukan pekerjaan apapun
tepat sesuai bahan dan pekerjaan yang sedang pada mesin.
Anda kerjakan.
5. Selalu gunakan kaca mata pengaman atau kaca Memasang gagang sisi (Gb. 2)
mata pelindung. Kaca mata biasa atau kaca mata Untuk keselamatan Anda sendiri, gunakan gagang sisi.
hitam BUKANLAH kaca mata pengaman. Pasang dengan menyekrupkannya pada tempat gagang.
6. Pegang mesin kuat-kuat dengan kedua tangan. Gagang sisi dapat diputar agar mudah dioperasikan.
7. Pastikan bahwa sabuk tidak menyentuh benda
kerja sebelum saklar dinyalakan. Memasang atau melepas sabuk ampelas
8. Jauhkan tangan dari bagian yang berputar. (Gb. 3)
9. Jangan tinggalkan mesin dalam keadaan hidup.
Lingkarkan sabuk pada puli depan. Pegang mesin seperti
Jalankan mesin hanya ketika digenggam tangan.
ditunjukkan pada gambar dan tekan ke bawah untuk
10. Mesin ini tidak tahan air, jadi jangan menggunakan
menarik kembali puli depan sehingga Anda dapat
air pada permukaan benda kerja.
menyelipkan ujung sabuk yang lain pada puli belakang.
Saat menekan mesin ke bawah, berhati-hatilah jangan
SIMPAN PETUNJUK INI. sampai membiarkan puli depan berputar secara tiba-tiba,
yang menyebabkan Anda kehilangan kendali pada mesin.
PERINGATAN:
JANGAN biarkan kenyamanan atau terbiasanya Anda CATATAN:
dengan produk (karena penggunaan berulang) • Tanda panah di bagian dalam sabuk dan yang ditandai
menggantikan kepatuhan yang ketat terhadap aturan pada puli belakang harus mengarah ke arah yang
keselamatan untuk produk yang terkait. sama. (Gb. 4)
PENYALAHGUNAAN atau kelalaian mematuhi kaidah
keselamatan yang tertera dalam petunjuk ini dapat
Menyambungkan ke pengisap debu
menyebabkan cedera badan serius. Makita
PERHATIAN:
DESKRIPSI FUNGSI • Selalu pasang tutup nosel saat pengisap debu tidak
tersambung ke nosel. Jangan sekali-kali memasukkan
PERHATIAN: jari Anda ke dalam nosel. (Gb. 5)
• Selalu pastikan bahwa mesin dalam keadaan mati dan Operasi pengampelasan yang lebih bersih bisa dilakukan
steker tercabut sebelum menyetel atau memeriksa dengan menghubungkan mesin ampelas sabuk ke
kerja mesin. pengisap debu Makita.
Saat menyambungkan ke pengisap debu Makita,
Kerja saklar (Gb. 1) diperlukan pilihan selang dengan diameter dalam 28 mm.
PERHATIAN: (Gb. 6)
• Sebelum memasukkan steker, selalu periksa apakah Saat menyambungkan ke pengumpul debu Makita (Model
picu saklar berfungsi dengan baik dan kembali ke 420S), tidak diperlukan selang pengumpul debu. Anda
posisi “OFF” saat dilepas. bisa menyambungkan mesin ampelas sabuk ke pilihan
Untuk menjalankan mesin, cukup tarik picu saklarnya. selang 28. (Gb. 7)
Lepaskan picu saklar untuk berhenti.
Untuk penggunaan terus-menerus, tarik picu saklar, tekan PENGGUNAAN
tombol kunci dan kemudian lepas picu saklar.
Untuk membebaskan posisi terkunci, tarik picu saklar PERHATIAN:
sampai penuh, dan kemudian lepaskan. • Tahan benda kerja menggunakan klem, dsb. jika ada
kemungkinan benda keja bergerak selama operasi
Saklar penyetel kecepatan kerja.
Kecepatan sabuk bisa disetel secara bebas antara 3,3 m • Mesin jangan sudah menyentuh permukaan benda
dan 16,6 m per detik dengan memutar saklar penyetel kerja saat Anda menyalakan atau mematikan mesin.
kecepatan ke setelan angka yang tersedia mulai dari 1 Bila tidak, bisa menyebabkan kurang baiknya hasil
sampai 6. akhir pengampelasan, kerusakan pada sabuk atau
Kecepatan yang lebih tinggi diperoleh jika saklar diputar kehilangan kendali pada mesin.
ke arah angka 6; kecepatan yang lebih rendah diperoleh • Saat bekerja menggunakan mesin, sangatlah berhati-
jika diputar ke arah angka 1. Pilih kecepatan yang tepat hati jangan sampai terjadi kontak antara mesin dan
untuk benda kerja yang akan diampelas. sabuk dengan bagian mana pun dari badan Anda atau
siapa pun atau apa pun yang ada di sekitar Anda.
PERHATIAN:
• Saklar penyetel kecepatan dapat diputar hanya sampai
6 dan kembali ke 1. Jangan dipaksa melewati 6 atau 1,
atau penyetel kecepatan bisa tidak berfungsi lagi .

10
Selalu gunakan gagang sisi (pegangan tambahan) dan
pegang mesin kuat-kuat pada kedua gagang sisi dan
pegangan saklar selama penggunaan. Nyalakan mesin
dan tunggu sampai mencapai kecepatan penuh. Tekan
mesin dengan lembut pada permukaan benda kerja lalu
gerakkan mesin maju dan mundur. Tekan sabuk sedikit
saja pada benda kerja. Tekanan yang berlebihan bisa
merusak sabuk dan memperpendek umur pakai mesin.

PERAWATAN
PERHATIAN:
• Selalu pastikan bahwa mesin dimatikan dan steker
dicabut sebelum melakukan pemeriksaan atau
perawatan.
• Jangan sekali-kali menggunakan bensin, tiner, alkohol,
atau bahan sejenisnya. Penggunaan bahan demikian
dapat menyebabkan perubahan warna, perubahan
bentuk atau timbulnya retakan.

Mengganti sikat karbon

Lepas dan periksa sikat karbon secara teratur. Ganti sikat
karbon ketika keausannya sudah sampai tanda batas.
Jaga agar sikat karbon tetap bersih dan tidak bergeser
dari tempatnya. Kedua sikat karbon harus diganti pada
waktu yang sama. Hanya gunakan sikat karbon yang
sama. (Gb. 8)
Gunakan obeng untuk melepas tutup tempat sikat. Tarik
keluar sikat karbon yang aus, masukkan yang baru dan
pasang tutup tempat sikat. (Gb. 9)
Untuk menjaga KEAMANAN dan KEANDALAN mesin,
perbaikan, perawatan atau penyetelan lain harus
dilakukan oleh Pusat Layanan Resmi Makita dan selalu
gunakan suku cadang pengganti buatan Makita.

PILIHAN AKSESORI
PERHATIAN:
• Dianjurkan untuk menggunakan aksesori atau
perangkat tambahan ini dengan mesin Makita Anda
yang ditentukan dalam petunjuk ini. Penggunaan
aksesori atau perangkat tambahan lain bisa
menyebabkan risiko cedera pada manusia. Hanya
gunakan aksesori atau perangkat tambahan sesuai
dengan peruntukkannya.
Jika Anda memerlukan bantuan lebih rinci berkenaan
dengan aksesori ini, tanyakan pada Pusat Layanan
Makita terdekat.
• Sabuk ampelas
• Selang 28
CATATAN:
• Beberapa item dalam daftar tersebut mungkin sudah
termasuk dalam paket mesin sebagai aksesori standar.
Hal tersebut dapat berbeda dari satu negara ke negara
lainnya.

11
TI NG VI T
Gi i thích v hình v t ng th
1. Nút khóa 7. M i tên 13. B ph n thu b i
2. C n kh i ng công t c 8. N p vòi x 14. V ch gi i h n
3. Tay c m hông 9. Vòi x 15. N p gi ch i
4. C n gi tay c m 10. ng d n 19 16. Tu c-n -vít
5. Pu-li sau 11. ng d n c a máy hút b i
6. Pu-li tr c 12. Máy hút b i

THÔNG S K THU T
Ki u 9031
Kích th c b ng 30 mm x 533 mm
T c b ng 3,3 - 16,6m/giây (200 - 1.000 m/phút)
Chi u dài t ng th 380 mm
Tr ng l ng t nh 2,1 kg
C p an toàn /II

• Do ch ng trình nghiên c u và phát tri n liên t c c a chúng tôi nên các thông s k thu t trong ây có th thay i mà
không c n thông báo tr c.
• Các thông s k thu t có th thay i tùy theo t ng qu c gia.
• Tr ng l ng tùy theo Quy trình EPTA tháng 01/2003
END201-6
L u gi t t c c nh báo và h ng
Ký hi u
Ph n d i ây cho bi t các ký hi u c dùng cho thi t b . d n tham kh o sau này.
m b o r ng b n hi u rõ ý ngh a c a các ký hi u này
Thu t ng “d ng c máy” trong các c nh báo c p n
tr c khi s d ng.
d ng c máy (có dây) c v n hành b ng ngu n i n
chính ho c d ng c máy (không dây) c v n hành
..... c tài li u h ng d n. b ng pin c a b n.
An toàn t i n i làm vi c
1. Gi n i làm vi c s ch s và có ánh sáng. N i
.............. CÁCH I N KÉP làm vi c b a b n ho c t i th ng d gây ra tai n n.
2. Không v n hành d ng c máy trong môi tr ng
ENE052-1
M c ích s d ng cháy n , ví d nh môi tr ng có s hi n di n
D ng c này c dùng ánh bóng b m t l n b ng c a các ch t l ng, khí ho c b i d cháy. Các d ng
các lo i v t li u g , nh a và kim lo i c ng nh các b m t c máy t o tia l a i n có th làm b i ho c khí b c
ã s n s n ph . cháy.
3. Gi tr em và ng i ngoài tránh xa n i làm vi c
ENF002-2 khi ang v n hành d ng c máy. S xao lãng có th
Ngu n c p i n khi n b n m t kh n ng ki m soát.
D ng c này ch c n i v i ngu n c p i n có i n áp
An toàn v i n
gi ng nh ã ch ra trên bi n tên và ch có th cv n
4. Phích c m c a d ng c máy ph i kh p v i c m.
hành trên ngu n i n AC m t pha. Chúng c cách i n
hai l p và do ó c ng có th c s d ng t các c m Không bao gi c s a i phích c m theo b t
k cách nào. Không s d ng b t k phích chuy n
i n không có dây ti p t.
i nào v i các d ng c máy c n i t (ti p
GEA005-3 t). Các phích c m còn nguyên v n và c m phù
C nh báo An toàn Chung dành h p s gi m nguy c i n gi t.
5. Tránh c th ti p xúc v i các b m t n i t
cho D ng c Máy ho c ti p t nh ng ng, b t n nhi t, b p ga
và t l nh. Nguy c b i n gi t s t ng lên n u c
C NH BÁO c t t c các c nh báo an toàn và th b n c n i t ho c ti p t.
h ng d n. Vi c không tuân theo các c nh báo và
6. Không d ng c máy ti p xúc v i m a ho c
h ng d n có th d n n i n gi t, ho ho n và/ho c
trong i u ki n m t. N c l t vào d ng c máy
th ng tích nghiêm tr ng. s làm t ng nguy c i n gi t.

12
7. Không l m d ng dây. Không bao gi s d ng dây 20. Rút phích c m ra kh i ngu n i n và/ho c ng t
mang, kéo ho c tháo phích c m d ng c máy. k t n i b pin kh i d ng c máy tr c khi th c
Gi dây tránh xa ngu n nhi t, d u, các mép s c hi n b t k công vi c i u ch nh, thay i ph
ho c các b ph n chuy n ng. Dây b h ng ho c tùng hay c t gi d ng c máy nào. Nh ng bi n
b r i s làm t ng nguy c i n gi t. pháp an toàn phòng ng a này s gi m nguy c vô
8. Khi v n hành d ng c máy ngoài tr i, hãy s tình kh i ng vô tình d ng c máy.
d ng dây kéo dài phù h p cho vi c s d ng ngoài 21. C t gi các d ng c máy không s d ng ngoài
tr i. Vi c dùng dây phù h p cho vi c s d ng ngoài t m v i c a tr em và không cho b t k ng i nào
tr i s gi m nguy c i n gi t. không có hi u bi t v d ng c máy ho c các
9. N u b t bu c ph i v n hành d ng c máy n i h ng d n này v n hành d ng c máy. D ng c
m t, hãy s d ng ngu n c p i n cb ov máy s r t nguy hi m n u c s d ng b i nh ng
b ng thi t b ng t dòng i n rò (RCD). Vi c s ng i dùng ch a qua ào t o.
d ng RCD s gi m nguy c i n gi t. 22. B o qu n d ng c máy. Ki m tra tình tr ng l ch
10. Chúng tôi luôn khuyên b n s d ng ngu n c p tr c ho c bó k p c a các b ph n chuy n ng,
i n qua thi t b RCD có th ng t dòng i n d hi n t ng n t v c a các b ph n và m i tình
nh m c 30 mA ho c th p h n. tr ng khác mà có th nh h ng n ho t ng
c a d ng c máy. N u có h ng hóc, hãy s a ch a
An toàn cá nhân
d ng c máy tr c khi s d ng. Nhi u tai n n x y
11. Luôn t nh táo, quan sát nh ng vi c b n ang làm
ra là do không b o qu n t t d ng c máy.
và s d ng nh ng phán oán theo kinh nghi m
23. Luôn gi cho d ng c c t c s c bén và s ch
khi v n hành d ng c máy. Không s d ng d ng
s . Nh ng d ng c c t c b o qu n t t có mép c t
c máy khi b n ang m t m i ho c ch u nh
s c s ít b k t h n và d i u khi n h n.
h ng c a ma tuý, r u hay thu c. Ch m t
24. S d ng d ng c máy, ph tùng và u d ng c
kho nh kh c không t p trung khi ang v n hành d ng
c t, v.v... theo các h ng d n này, có tính n i u
c máy c ng có th d n n th ng tích cá nhân
ki n làm vi c và công vi c c th c hi n. Vi c s
nghiêm tr ng.
d ng d ng c máy cho các công vi c khác v i công
12. S d ng thi t b b o h cá nhân. Luôn eo thi t b
vi c d nh có th gây nguy hi m.
b o v m t. Các thi t b b o h nh m t n ch ng
b i, giày an toàn ch ng tr t, m b o h hay thi t b B o d ng
b o v thính giác c s d ng trong các i u ki n 25. nhân viên s a ch a trình b o d ng
thích h p s giúp gi m th ng tích cá nhân. d ng c máy c a b n và ch s d ng các b ph n
13. Tránh vô tình kh i ng d ng c máy. mb o thay th ng nh t. Vi c này s m b o duy trì
công t c v trí off (t t) tr c khi n i ngu n i n c an toàn c a d ng c máy.
và/ho c b pin, c m ho c mang d ng c máy. Vi c 26. Tuân theo h ng d n dành cho vi c bôi tr n và
mang d ng c máy khi ang t ngón tay v trí công thay ph tùng.
t c ho c c p i n cho d ng c máy ang b t th ng 27. Gi tay c m khô, s ch, không dính d u và m .
d gây ra tai n n.
GEB015-3
14. Tháo m i khoá ho c chìa v n i u ch nh tr c khi
b t d ng c máy. Vi c chìa v n ho c khoá v n còn C NH BÁO AN TOÀN IV I
g n vào b ph n quay c a d ng c máy có th d n
n th ng tích cá nhân.
MÁY CHÀ NHÁM B NG
15. Không v i quá cao. Luôn gi th ng b ng t t và có 1. Gi d ng c máy b ng các b m t kép cách i n,
ch chân phù h p. i u này cho phép i u khi n vì dây b ng có th ti p xúc v i dây i n c a chính
d ng c máy t t h n trong nh ng tình hu ng b t ng . nó. Vi c c t m t dây d n “có i n” có th khi n các b
16. n m c phù h p. Không m c qu n áo r ng hay ph n kim lo i b h c a d ng c máy “có i n” và làm
eo trang s c. Gi tóc, qu n áo và g ng tay cho ng i v n hành b i n git.
tránh xa các b ph n chuy n ng. Qu n áo r ng, 2. C n thông thoáng phù h p cho khu v c làm vi c
trang s c hay tóc dài có th m c vào các b ph n khi b n th c hi n thao tác ánh nhám.
chuy n ng. 3. M t s v t li u có th ch a hoá ch t c. Ph i c n
17. N u các thi t b c cung c p k t n i các thi t tr ng tránh hít ph i b i và ti p xúc v i da. Tuân
b thu gom và hút b i, hãy m b o chúng c theo d li u an toàn c a nhà cung c p v t li u.
k t n i và s d ng h p lý. Vi c s d ng thi t b thu 4. Luôn luôn s d ng úng m t n ch ng b i/kh u
gom b i có th làm gi m nh ng m i nguy hi m liên trang i v i lo i v t li u và ng d ng b n ang
quan n b i. làm vi c.
S d ng và b o qu n d ng c máy 5. Luôn s d ng g ng tay ho c kính b o h . M t
18. Không dùng l c i v i d ng c máy. S d ng th ng ho c kính râm KHÔNG ph i là lo i kính an
úng d ng c máy cho công vi c c a b n. S toàn.
d ng úng d ng c máy s giúp th c hi n công vi c 6. C m ch c d ng c b ng c hai tay.
t t h n và an toàn h n theo giá tr nh m c c 7. Ph i m b o r ng dây b ng không ti p xúc v i
thi t k c a d ng c máy ó. v t gia công tr c khi b t công t c lên.
19. Không s d ng d ng c máy n u công t c không 8. Gi tay tránh xa các b ph n quay.
b t và t t c d ng c máy ó. M i d ng c máy 9. Không m c d ng c ho t ng. Ch v n hành
không th i u khi n c b ng công t c u r t d ng c khi c m trên tay.
nguy hi m và c n c s a ch a. 10. D ng c này không c ch ng th m, do ó
không c dùng n c cho b m t gia công.
13
L U GI CÁC H NG D N NÀY. li tr c b t ng xoay s làm b n không ki m soát c
d ng c .
C NH BÁO: L U Ý:
KHÔNG c s tho i mái hay quen thu c v i s n • M i tên bên trong dây b ng và m i tên c ánh
ph m (có c do s d ng nhi u l n) thay th vi c d u trên pu-li sau ph i cùng ch v m t h ng.
tuân th nghiêm ng t các quy nh v an toàn dành (Hình 4)
cho s n ph m này. VI C DÙNG SAI ho c không tuân
theo các quy nh v an toàn c nêu trong tài li u K t n i vào máy hút b i Makita
h ng d n này có th d n n th ng tích cá nhân
nghiêm tr ng. C N TR NG:
• Luôn óng n p vòi x khi máy hút b i không ck t
n i v i vòi x . Không bao gi a ngón tay b n vào vòi
MÔ T CH C N NG x . (Hình 5)
C N TR NG: Có th th c hi n các thao tác ánh nhám c s ch s
• Ph i luôn m b o r ng d ng c ã c t t i n và h n b ng cách k t n i máy chà nhám b ng vào máy hút
ng t k t n i tr c khi ch nh s a ho c ki m tra ch c b i Makita.
n ng c a d ng c . Khi k t n i v i máy hút b i Makita, c n ph i có ng d n
ng kính trong là 28 mm. (Hình 6)
Ho t ng công t c (Hình 1) Khi k t n i vào túi thu b i Makita (Ki u 420S), ph n ng
d n c a túi thu b i này s không c n thi t. B n có th k t
C N TR NG: n i máy chà nhám b ng tr c ti p vào ng d n tùy ch n
• Tr c khi c m i n vào d ng c , luôn luôn ki m tra 28. (Hình 7)
xem c n kh i ng công t c có ho t ng bình th ng
hay không và tr v v trí “OFF” (T T) khi nh ra.
kh i ng d ng c , ch c n kéo c n kh i ng công
V N HÀNH
t c. Nh c n kh i ng công t c ra d ng. C N TR NG:
v n hành liên t c, hãy kéo c n kh i ng công t c, • Gi ch t v t gia công b ng bàn k p, v.v... n u nó có
nh n nút khóa và sau ó nh c n kh i ng công t c ra. kh n ng tr t trong quá trình thao tác.
d ng d ng c t v trí ã khóa, hãy kéo c n kh i ng • D ng c này không c ti p xúc s n v i b m t
công t c h t m c, r i sau ó nh ra. v t gia công khi b n b t ho c t t d ng c . N u không
có th làm cho b m t hoàn thi n chà nhám kém ch t
a i u ch nh t c l ng, gây h h ng cho dây b ng ho c m t ki m soát
Có th i u ch nh t c b ng không gi i h n t 3,3 m d ng c .
n 16,6 m m i giây b ng cách xoay a i u ch nh t c • Khi thao tác v i d ng c , c n h t s c c n th n tránh
n cài t s ã có s n t 1 n 6. b t c ti p xúc nào gi a d ng c và dây b ng v i m i
Có th tt c cao h n khi xoay a này v h ng s b ph n c a c th ho c b t c ai ho c m i th nào
6, av t c th p h n khi xoay a v h ng s 1. g n b n.
Hãy ch n t c phù h p cho v t gia công c n c chà Luôn s d ng tay c m bên hông (tay c m ph tr ) và gi
nhám. ch t d ng c b ng c hai tay c m bên hông và i tay
C N TR NG: c m trong lúc v n hành. B t d ng c lên và ch n khi
• a i u ch nh t c ch có th c xoay n s 6 và tt c t i a. Nh nhàng a d ng c lên b m t v t
tr v s 1. Không c c xoay quá s 6 ho c s 1, gia công và di chuy n d ng c t i lui. Ch c n nh
n u không ch c n ng i u ch nh t c có th s dây b ng lên v t gia công. n quá m nh có th làm h ng
không còn ho t ng c. dây b ng và gi m tu i th d ng c .

L P RÁP B O TRÌ
C N TR NG: C N TR NG:
• Luôn luôn m b o r ng d ng c ã c t t và tháo • Hãy luôn ch c ch n r ng d ng c ã c t t và ng t
phích c m tr c khi dùng d ng c th c hi n b t c k t n i tr c khi c g ng th c hi n vi c ki m tra hay
công vi c nào. b o d ng.
• Không bao gi dùng x ng, ét x ng, dung môi, c n
L p t tay c m hông (Hình 2) ho c hóa ch t t ng t . Có th x y ra hi n t ng m t
Vì s an toàn c a chính b n, hãy luôn luôn s d ng tay màu, bi n d ng ho c n t v .
c m hông. L p t nó b ng cách v n vít th t ch t vào c n
gi tay c m. Có th xoay tay c m hông v n hành d Thay th các ch i các-bon
dàng h n. Hãy tháo và ki m tra các ch i các-bon nh k . Thay th
khi ch i ã mòn n v ch gi i h n. Hãy gi cho các ch i
L p ho c tháo dây b ng nhám (Hình 3) các-bon s ch s và không qu n vào trong các u gi .
L ng dây b ng lên trên pu-li tr c. Gi d ng c nh th Các ch i các-bon nên c thay th cùng lúc. Hãy s
hi n trong hình và nh n xu ng nh m co l i pu-li tr c d ng các ch i các-bon gi ng nhau. (Hình 8)
b n có th tr t u kia c a dây b ng lên trên pu-li sau. Hãy s d ng m t tu c-n -vít tháo các n p gi ch i.
Khi nh n xu ng d ng c , c n th n không c cho pu- Hãy tháo các ch i các-bon ã b mòn, l p vào các ch i
m i và v n ch t các n p gi ch i. (Hình 9)

14
 m b o AN TOÀN và TIN C Y c a s n ph m, vi c
s a ch a ho c b t c thao tác b o trì, i u ch nh nào u
ph i c th c hi n b i các Trung tâm D ch v c y
quy n c a Makita (Makita Authorized Service Center),
luôn s d ng các ph tùng thi t b thay th c a Makita.

PH KI N TÙY CH N
C N TR NG:
• Các ph ki n ho c ph tùng g n thêm này c
khuy n cáo s d ng v i d ng c Makita c a b n theo
nh quy nh trong h ng d n này. Vi c s d ng b t
c ph ki n ho c ph tùng g n thêm nào khác u có
th gây ra r i ro th ng tích cho ng i. Ch s d ng
ph ki n ho c ph tùng g n thêm cho m c ích ã quy
nh s n c a chúng.
N u b n c n h tr bi t thêm chi ti t v nh ng ph
ki n này, hãy liên h v i Trung tâm D ch v c a Makita t i
a ph ng c a b n.
• Dây b ng nhám
• ng d n 28
L U Ý:
• M t vài m c trong danh sách có th c bao g m
trong gói d ng c làm ph ki n tiêu chu n. Các thông
s k thu t có th thay i tùy theo t ng qu c gia.

15
!"#"$%&
'(")*+,"&-)./0//).%123$4
1. BN9V 2Y%+ 7. 2:)H* 13. !+*#$%&D/)UNV"
2. =-.7ML=/$&&(" 8. U(P.DG6%*3?(0 14. 8@D';()/D
3. D,(9'/?D,("8,(& 9. G6%*3?(0 15. U(BZDG@$0OD1B*&
4. G@$0ODD,(9'/? 10. =(0 19 16. C8+-&
5. *%)D,("F2/& 11. =(08%&!+*#$%&D:DUNV"
6. *%)D,("F",( 12. G@$D:DUNV"

!"#$%&'()*+),
*N6" 9031
8"(D=(04(" 30 99. x 533 99.
+-(9!*Y-=(04(" 3.3 - 16.69./-."(G@ (200 - 1,000 9./"(G@)
+-(90(-ED0*-9 380 99.
"A;(F"/)=NG[. 2.1 )).
9(7*\("+-(9B2%D]/0 /II
! !"#$%&'())(*+,"+-,(-.'/01234/5"(%06(&76%!"#$%& 8,%9:2';(!4(3<"!%)=(*>?/?"@A%('!B2@$0"1B2&CD,ED0C967,%&1',&<F,G*(?26-&F",(
! 8,%9:2';(!4(3%('17)76(&)/"CB<"17623B*3!GH
! "A;(F"/)7(98,%?/&+/?8%& EPTA 01/2003
END201-6 GEA005-3
!"#$"%&'( -()*./#01")0-2)$3&#1456!#7
76%CB"@A+#%=/I2/)JKLG@$<M,=;(F*/?%NB)*KL
EB*DHO)J(+-(9F9(08%&=/I2/)JKL<F,!8,(<')6%")(*<M,&("
*-8/#9 7$/#:;;<)=592:3
!"#$%&'( ')#(!"#$%&'(*+#(!,#-./'*0123/4!"#3(4("#
.....%6("+:69#%)(*<M,&(" 5176 8-* !"#$%&'()*,+ ,) "%-."/,012345-."3252."6+7!4&"81"9:&7;4
<=>/!)6$??@"AB1, $?$=%> 345/=#01$6>#*+ *"6/9B*1C&"7#>"C3#7

................>"-"=%&M/A" *>?@85>A)-()*./#0B&,-()B0,0()=5C7D$1
ENE052-1 :2"*3E0!"#$%&#")7#F7G0#0)-.
!"#$%&'()*+,(-)%./,(0.,
+;(-6( "!+*#$%&9#%CQQR(# <"+;(!7#%""@A F9(0SO& !+*#$%&9#%CQQR( (9@
!+*#$%&9#%"@A<M,=;(F*/?8/DP.-F",(-/=DNC9, 42(=7.)123E2F3 72%D
=(0) G@$G;(&("ED0<M,)*31=CQQR( F*#%!+*#$%&9#%CQQR( (C*,=(0) G@$
'"4#A"P.-G@$G;(=@
G;(&("ED0<M,1?7!7%*@$
ENF002-2
1234(!45678 )950$3,#:;6+,(<.=>?@/?A5(5>
+-*!M#$%976%!+*#$%&9#%)/?1F26&'6(0CQG@$9@1*&D/"CQQR(7(9G@$*3?NC-, 1. #B13<.=>?@?/ A5(5>C2D0@)950'&,5#13&0@1'(78'945( 4#A"G@$
<"BR(08,%9:28%&!+*#$%&9#% 123'37,%&<M,CQQR()*31==2/?1??!Q= *)*3!)3*3)3F*#%9#DGO?%('";(CB=:6)(*!).D%N?/7.!F7NCD,
!D@0-!G6("/A" %NB)*KL"@ACD,*/?)(*FN,9>"-"=%&M/A"123=(9(*S<M,)/? 2. ,645CED(5>-)%./,(0.,788F5C>':5<?@/,5!-GH#G5%%&-IH#
B2/T)CQG@$C969@=(0D."CD, -E4> C>'J5>?@/?@/0@+,(-239 GK5L 2%.,M"N>O(?@/0@)"P'0I;QH
7978 !+*#$%&9#%CQQR('3=*,(&B*3)(0CQ!4#$%'NDM"-" UN"V P&
F*#%)W(XD/&)26(-

16
3. *93/:-);8+-$< *=>? 8@&'AB!!/'&(C '29;) (A@D$,E5<C>#" /17;F+ 14. >A5G"W1!$%;I1Q4(2%.,$%&1!,,GG4,>?@/!&-$Y#-)%./,(0.,
$!@&'C 7-&':GGH# !"#%D:7)E #*!82:%"F)1"9G."<=>-I
H :JK/:DC 788F5 B*31'F*#%)NI1'G@$!=@0?+,(&%0:6<"M.A"=6-"G@$F9N"CD,8%&
!"#-8*-H% !+*#$%&9#%CQQR(%('G;(<F,+NKCD,*/??(D!'Y?
)950$3,#:;6#D5>788F5 15. ,645?A5(5>C>%&6&?@/'"#-,.=,0 !;#?45G5%6.>13&G5%
4. $3;RG+,(-)%./,(0.,788F5QD,(<,#@G;I-QD5%;I ,645#;#1$3( ?%(Q;9C2D-205&'0Q3,#-935 !4*(3'3G;(<F,+-?+N9
$3;RG704945G%P@C#S ,645CED$3;RG,&1#T$-Q,%*G;I-)%./,(0., !+*#$%&9#%CQQR(CD,D@8OA"<"=S(")(*KLG@$C96+(D+.D
788F5?@/Q,4 '56#H> B2/T)G@$C96S:)D/D1B2&123!7,(*/?CQG@$!8,()/" 16. 1Q4(G56C2D-205&'0 ,645'90-)%./,(1Q4(G56?@/2390-GH>
4%D@'3M6-02D+-(9!=@$0&8%&)(*!).DCQQR(MY%7 7$ 2%.,'90-)%./,($%&#;I #B13704C2D-'D>O0 -'.=,OD5 13&
5. %&9;(,645C2D%45(G56';0O;'G;I<.=>OH9?@Q/ 4,'56#H> -E4> ?4, J"(0.,,6B4CG3DE>H= '49>?@/-)3./,>?@/ !=#A%P,(*N69*6(9 !+*#$%&B*3D/?
-)%./,(>A5)950%D,> -Q52"(QD0 13&QB-D 6T> 9@+-(9!=@$0&G@$'3 F*#%P9G@$9+@ -(90(-%('!8,(CB7.D<"M.A"=6-"G@$!+2#$%"G@$
!).DCQQR(MY%7=:&8OA" F()*6(&)(08%&+NK=/9P/=)/?4#A" 17. 25G0@G5%!;#,"$G%P*'A52%;I#B#13&!;#-GTIM"N>79DC>
6. ,645C2D-)%.,/ (0.,788F5JBG>=A52%.,,6B4C>':5<-$U6GE.=> "A;( 'J5>?@/ C2DQ%9!',I9457#D-E.,/ 0Q4,13&CED(5>,"$G%P*>;=>
G@$CF2!8,(CB<"!+*#$%&9#%CQQR('3!4.$9+-(9!=@60&8%&)(*!).D ,645(-205&'0 )(*<M,!+*#$%&D:D123'/D!)Y?UNV"'3M6-02D
CQQR(MY%7 %/"7*(0G@$!).D'()UNV"P&CD,
7. ,645CED'5678,645(704-205&'0 ,645CED'5678-<./,6G #V( G5%CED13&#B13-)%./,(0.,788F5
2%., J,#$3;RG-)%./,(0.,788F5 -GTI'5678C2D245(!5G 18. ,645MZ>CED-)%./,(0.,788F5 CED-)%./,(0.,788F5?@/-205&'0
)950%D,> >=A50;> +,(0@)0 2%.,EH>= '49>?@/-)3./,>?@/ =(0G@$ G;IG5%CED(5>+,()"P !+*#$%&9#%CQQR(G@$!F9(3=9'3G;(<F,CD,
M;(*NDF*#%4/")/"'3!4.$9+-(9!=@$0&8%&)(*!).DCQQR(MY%7 &("G@$9@B*3=.G[.](4123B2%D]/0)-6(7(98@D+-(9=(9(*S
8. +P&?@/CED(5>-)%./,(0.,788F5>,G,5)5% )9%CED'56Q4, 8%&!+*#$%&G@$CD,*/?)(*%%)1??9(
<49(?@/-205&'0G;I(5>:56>,G,5)5% )(*<M,=(0G@$ 19. ,645CED-)%./,(0.,788F5 25G'9HQE*704'505%J-$Y#$Y#7#D
!F9(3=9)/?&("](0"%)%(+(*'32D+-(9!=@$0&8%&)(*!).D !+*#$%&9#%CQQR(G@$+-?+N9D,-0=-.7MLC96CD,!B^"=.$&%/"7*(0123
CQQR(MY%7 7,%&CD,*/?)(*X6%91X9
9. 25GQD,(CED(5>-)%./,(0.,788F5C>'J5>?@/-$U6GE.=> C2DCED 20. J,#$3;RG!5G1234(!45678 13&/2%.,E"#1IQ-Q,%@,/ ,G
,"$G%P*$,F (G;>G%&1'78%;/9 (RCD) )(*<M, RCD '32D !5G-)%./,(0.,788F5G4,>?A5G5%$%;I1Q4( -$3@/6>,"$G%P*
+-(9!=@$0&8%&)(*!).DCQQR(MY%7 -'%H0 2%.,!;#-GTI-)%./,(0.,788F5 -.[)@ (*BR%&)/"D,("+-(9
10. +,1>&>A5C2DCED1234(!45678O45> RCD ?@/0@G%&1'78%;/9 B2%D]/0D/&)26(-'3M6-02D+-(9!=@$0&8%&)(*!BZD<M,&("
C>,;Q%5704-GH> 30 mA -'0, !+*#$%&9#%CQQR(%06(&C967/A&<'
)950$3,#:;6'49>I"))3 21. !;#-GTI-)%./,(0.,788F5?@/7047#DCED(5>C2D245(!5G0.,-#TG
11. C2D%&0;#%&9;( 13&';(-GQ-'0,945)"PGA53;(?A5'H/(C#,6B4 13&,645,>"W5QC2DI"))3?@/704)"D>-)6G;I-)%./,(0.,788F5
13&CED'50;W'A5>VGC>+P&CED(5>-)%./,(0.,788F5 ,645CED 2%.,)A51>&>A5-2345>@=CED(5>-)%./,(0.,788F5 !+*#$%&9#%
(5>-)%./,(0.,788F5C>+P&?@/)"PGA53;(-2>./,6 2%.,C> CQQR('3!B^"%/"7*(0!9#%$ %0:6<"9#%8%&P:,G@$C96CD,*/?)(*U_)%?*9
':5<?@/0V>-05!5G65-'<QH# -)%./,(#.0/ 1,3G,X,3* 2%., 22. G5%#B13%;G[5-)%./,(0.,788F5 Q%9!',IG5%$%&G,I?@/
G5%CED65 M/$-8K3G@$8(D+-(9*39/D*3-/&!9#$%);(2/&<M,&(" 704JBGQD,(2%.,G5%-E.,/ 0Q4,+,(EH=>'49> ?@/-)3./,>?@/ G5%
!+*#$%&9#%CQQR(%('G;(<F,+K N CD,*/??(D!'Y?%06(&*N"1*& 1QG2;G+,(EH>= '49> 2%.,':5<,./>S ?@/,5!'4(O3G%&?I
12. CED,"$G%P*$F,(G;>'49>I"))3 '90194>Q5$F,(G;>-'0, Q4,G5%?A5(5>+,(-)%./,(0.,788F5 25G0@)950-'@6256 C2D
%NB)*KLB%R &)/" !M6" F",()())/"UN"V *%&!G,(".*]/0)/"2#$" F9-) >A5-)%./,(0.,788F57$L4,01L0G4,>G5%CED(5> %N?/7.!F7N
".*]/0 F*#%!+*#$%&BR%&)/")(*CD,0."G@$<M,<"=](4G@$!F9(3=9'3 ';("-"9()!).D'())(*D:12*/)J(!+*#$%&9#%CQQR(%06(&C96
M6-02D)(*?(D!'Y? S:)7,%&
13. $F,(G;>704C2D-$Y#CED(5>,645(704Q;=(C! Q%9!',I945'9HQE* 23. 3;I)950)013&?A5)950'&,5#-)%./,(0.,G5%Q;#,6B4-'0,
,6B4C>QA512>4($Y#G4,>-E.,/ 0Q4,G;I1234(!45678 13&/2%., !+*#$%&9#%)(*7/DG@9$ @)(*D:12%06(&S:)7,%&1239@8%?)(*7/D+9
E"#1IQ-Q,%@/ 2%.,G4,>G5%6G2%.,J.,-)%./,(0., )(*=%D 9/)'39@B`IF(7.D8/D",%0123+-?+N9CD,&6(0)-6(
".A-9#%?*.!-K=-.7ML!4#$%S#%!+*#$%&9#%CQQR( F*#%)(*M(*L'CQ 24. CED-)%./,(0.,788F5 ,"$G%P*-'%H0 13&9;'#"'H=>-$3.,( \3\
!+*#$%&9#%CQQR(<"8K3G@$!BZD=-.7ML%0:6%('";(CB=:6)(*!).D Q50)A51>&>A5#;(G3459 <H!5%P5':5<G5%?A5(5>13&
%N?/7!. F7N (5>?@/!&3(0.,?A5 )(*<M,!+*#$%&9#%CQQR(!4#$%G;(&("%#$""%)
!F"#%'()G@$);(F"DC-,%('G;(<F,!).D%/"7*(0

17
G5%I%HG5% -()#LF@)6>)8=()7)0
25. >A5-)%./,(0.,788F5-+D5%;II%HG5%!5GE45(L4,0 ?@/O54 >G5%
%;I%,(]#6CED,&72341II-#@69G;>-?45>;=> !4*(3'3G;(<F, +D,)9%%&9;(:
)(*<M,!+*#$%&9#%CQQR(9@+-(9B2%D]/0 ! 7*-'=%?<F,1"6<'-6(=-.7ML!+*#$%&9#%%0:6<"7;(1F"6&BZD!+*#$%&
26. .IDA%1 %D #-!"#3(4("#;(>#@8/)'/&(C 3/4>#@$./<2C ( 123S%DB2/T)!+*#$%&9#%%%))6%"B*/?7/A&F*#%7*-'=%?)(*G;(
'B.>@EJ$K@D- &("8%&!+*#$%&9#%
27. #B130.,!;IC2D12D( '&,5# 13&7040@>=A50;>13&!5%&I@
%)*+,)-)./0-!1234( (5)6+78 1)
-$Z^,>
+D,)9%%&9;(:
GEB015-3
! )6%"!=@0?B2/T)!+*#$%&9#% <F,7*-'=%?-6(=-.7ML=/$&&("=(9(*SG;(
-()*./#01")0-2)$3&#1456!#7 &("CD,%06(&S:)7,%& 123)2/?CB0/&7;(1F"6& "OFF# !9#$%B26%0
*-8/#9 7!51B@@H)6+)0 !BZD<M,!+*#$%&9#%ED0DO&=-.7ML=/$&&(" B26%0=-.7ML=/$&&("!4#$%F0NDG;(
1. J.,-)%./,(0.,?@/#D50!;I2"D0_>9>-?45>;=> ->./,(!5G'56<5> &("
,5!!&';0O;'G;I'5678+,(Q;9-,(7#D )(*7/DS:) "9@)*31= S,(7,%&)(*<M,&("%06(&76%!"#$%& DO&=-.7ML=/$&&(" )DBN9V 2Y%+ 12,-
CQQR(CF2P6("# %('G;(<F,=6-"G@$!B^"E2F38%&!+*#6%&9#%CQQR(G@$ B26%0=-.7ML=/$&&("
C969>@ "-"FN,9 "9@)*31=CQQR(CF2P6("# 123G;(<F,P:,Ba.?/7.&(" S,(7,%&)(*!2.)<M,&("!+*#$%&9#%'()7;(1F"6&2Y%+ <F,DO&=-.7ML=/$&&("
S:)CQQR(MY%7CD, '"=ND '()"/A"B26%0=-.7ML
2. <.=>?@/?A5(5>QD,(0@G5%%&I56,5G5`,645(-<@6(<,-0./,)"P 9:;.:*"<=1)>?*@1
?A5G5%+;#
=(9(*SB*/?+-(9!*Y-<"*3D/?<D)YCD,7/A&176 3.3 9. SO& 16.6 9. 76%
3. 9;'#"I5(,645(,5!0@'5%-)0@?@/-$a><H[ %&9;(,645'B##0M"N>
-."(G@ED0)(*B*/?1BR"B*/?*3D/?CB0/&F9(0!2876(&b 1 SO& 6
2%.,C2D'5%-2345>;>= ';0O;'G;I%45(G56 $bHI;QHQ50+D,0B3
#D5>)950$3,#:;6+,(OBDO3HQ9;'#" +NK=(9(*SB*/?+-(9!*Y-<F,!*Y-8OA"CD,ED0)(*F9N"CBG(&F9(0
4. CED2>D5G5GG;>M"N>/)9;><H[?@/JBGQD,(G;I9;'#"13&G5%CED !28 6 123B*/?+-(9!*Y-<F,M,(2&CD,ED0)(*F9N"B*/?CBG(&F9(0
(5>?@/)"PGA53;(?A5(5>,6B4C>?"GS )%;=( !28 1
5. '90194>Q5>H%:;62%.,194>)%,IQ5-'0, 194>Q5$GQH +D,)9%%&9;(:
2%.,194>G;>1##704CE4194>>H%:;6 ! BNV9F9N"B*/?+-(9!*Y-=(9(*SF9N"CB'"=NDG@$F9(0!28 6 123
6. !;I-)%./,(0.,C2D1>4>#D960.,?;=(',(+D5( F9N")2/?'"SO&F9(0!28 1 %06(Uc"F9N"!20F9(0!28 6 F*#% 1
7. Q%9!',IC2D1>4C!945'56<5>>;>= 7047#D';0O;'G;IEH=>(5>
C96!M6""/A"Q`&)LM/")(*B*/?+-(9!*Y-%('C96=(9(*S<M,&("CD,%@)
G4,>?@/!&-$Y#'9HQE*
8. %&9;(,645C2D0.,';0O;'G;IEH=>'49>?@/20">7#D 76%CB
9. ,645$34,6C2D-)%./,(0.,?A5(5>)D5(79D CED(5>-)%./,(0.,C>
+P&?@/J.,,6B4-?45>;>= >)838,>#@
10. -)%./,(0.,>@=704G;>>=A5 #;(>;>= ,645CED>=A5I><.D>OH9+,(EH>= (5>
+D,)9%%&9;(:
! 7*-'=%?<F,1"6<'-6(=-.7ML!+*#$%&9#%%0:6<"7;(1F"6&BZD!+*#$%&
3IF@.5 F.)$-()B0,0()*D&J)0KC 123S%DB2/T)!+*#$%&9#%%%))6%"D;(!"."&("<Db )/?!+*#$%&9#%
)A5-Q.,>:
,645C2D)950704%&0;#%&9;(2%.,)950)"D>-)6G;IO3HQ:;Pc* %)*32A3"B-AC)>D"<AC)./C)- (5)6+78 2)
(!5GG5%CED(5>L=A52356)%;=() ,6B4-2>.,G5%$bHI;QHQ50 !4#$%+-(9B2%D]/08%&7/-+NK!%& EB*D<M,D,(9'/?D,("8,(&!=9% 7.D
Gd-GPc*#5D >)950$3,#:;6C>G5%CED(5>O3HQ:;Pc*,645( 7/A&ED0)(*8/"=)*:G@$G@$0ODD,(9'/?<F,1"6" =(9(*SF9N"D,(9'/?D,("
-)%4()%;# G5%CED(5>,645(704-205&'02%.,G5%704$bHI;QHQ50 8,(&CD,!4#$%)(*<M,&("CD,%06(&&6(0D(0
Gd-GPc*#5D >)950$3,#:;6C>)B40.,CED(5>>@,= 5!G4,C2D-GH#
G5%I5#-!TI,645(%">1%( %)*32A3"B-E*F0G0A!)H6)./"A (5)6+78 3)
<=6=(04("?"*%)D,("F",( S#%!+*#$%&9#%7(9G@$1=D&C-,<"*:B](4
12,-)D*%)D,("F",(2&!4#$%<F,+NK=(9(*S<=6=(04("C-,G@$*%)D,("
F2/&CD, !9#$%)D!+*#$%&9#%2& EB*D*3-/&%06(<F,*%)D,("F",(F9N"ED0
C96CD,7/A&<'123%('G;(<F,+K N !=@0)(*+-?+N9!+*#6%&9#%CD,

18
2056-2Q": %)*?:$7H8 .9:*-=)*(<0.
! 2:)H*G@D$ ,("<"8%&=(04("123G@$%0:6?"*%)D,("F2/&'37,%&M@ACB S%D1B*&+(*L?%"%%)9(7*-'=%?!B^"B*3';( !B2@$0"1B*&
<"G(&!D@0-)/" (:5<?@/ 4) +(*L?%"!9#%$ =O)F*%'"SO&8@D';()/D */)J(1B*&+(*L?%"<F,=3%(D
123%06(<F,1B*&+(*L?%"F2ND!8,(CB<"G@$0OD +-*!B2@$0"1B*&
%)*?4F80>3I0?=*F80-AJAKL.M Makita
+(*L?%"G/A&=%&1B*&4*,%9)/" <M,1B*&+(*L?%"G@$);(F"D!G6("/A"
+D,)9%%&9;(: (:5<?@/ 8)
! BZDU(BZDG6%*3?(0!=9%!9#%$ CD,!M#$%976%!+*#$%&D:DUNV"!8,( <M,C8+-&!4#$%S%DU(BZDG@$0OD1B*&%%) ";(1B*&+(*L?%"G@$=O)F*%
)/?G6%*3?(0 %06(=%D".A-9#%8%&+NK!8,()/?G6%*3?(0 %%)9( <=61B*&+(*L?%"<F96!8,(CB 123BZDU(BZDG@60OD1B*&<F,1"6"
(:5<?@/ 5) (:5<?@/ 9)
=(9(*S<M,&(")(*8/D%06(&=3%(DCD,ED0!M#$%976%!+*#$%&8/D1?? !4#$%+-(9B2%D]/0123+-(9"6(!M#$%S#%8%&P2.7]/KfL +-*<F,H:"0L
=(04("!8,()/?!+*#$%&D:DUNV" Makita ?*.)(*G@$P6(")(**/?*%&'() Makita !B^"P:,D;(!".")(*X6%91X9
!9#$%!M#$%976%)/?!+*#$%&D:DUNV"'() Makita '37,%&<M,%NB)*KL!=*.9 ?;(*N&*/)J( 123G;()(*B*/?7/A&%#$"b "%)'()"@A<F,<M,%3CF268%&1G,
=(0!=,"P6("H:"0L)2(&](0<" 28 99. (:5<?@/ 6) '() Makita !=9%
!9#$%!M#$%976%)/?!+*#$%&D:DUNV" Makita (*N6" 420S) '3C96';(!B^"7,%&<M,
=(08%&!+*#$%&D:DUNV" +NK=(9(*S!M#$%976%!+*#$%&8/D1?? #N3>8OP*H8F$
=(04("!8,()/?%NB)*KL!=*.9=(0 28 CD,ED07*& (:5<?@/ 7)
+D,)9%%&9;(:
>)8GM"7)0 ! 8%1"3";(<F,<M,!>4(3%NB)*KL!=*.9F*#%%NB)*KL7%6 46-&!F26("@A
)/?!+*#$%&9#% Makita G@$*3?N<"+:69%# )(*<M,%NB)*KL!=*.9F*#%
+D,)9%%&9;(: %NB)*KL76%46-&%#$"b %('9@+-(9!=@$0&G@$'3CD,*/??(D!'Y? <M,
! <M,+@9F"@? d2d !4#$%0ODM.A"&("<F,1"6F()M.A"&("%('=(9(*S %NB)*KL!=*.9F*#%%NB)*KL76%46-&7(9-/7SNB*3=&+LG*@$ 3?NC-,!G6(
!+2#$%"G@C$ D,<"*3F-6(&)(*G;(&(" "/A"
! C96+-*<F,!+*#$%&9#%=/9P/=)/?4#A"P.-8%&M.A"&(")6%"G@$+NK'3!BZD F()+NK7,%&)(*G*(?*(023!%@0D!)@$0-)/?%NB)*KL!=*.9!F26("@A
F*#%BZD!+*#$%&9#% 9.>3"/A" %('G;(<F,M.A"&("C96!*@0?*,%0 !).D EB*D=%?S(9H:"0L?*.)(* Makita <)2,?(, "+NK
+-(9!=@0F(076%=(04(" F*#%=:I!=@0)(*+-?+N9!+*#$%&9#%CD, ! =(04("8/D
! !9#$%<M,&("!+*#$%&9#% EB*D*39/D*3-/&%06(<F,=6-"<D=6-"F"O$& ! =(0 28
8%&*6(&)(08%&+NKF*#%P:,G@$%0:6<"?*.!-K<)2,!+@0&=/9P/=)/?
2056-2Q":
!+*#$%&9#%123=(04("
! %NB)*KL?(&*(0)(*%(''3*-9%0:6<"MND%NB)*KL4#A"\("8%&
<M,D,(9'/?D,("8,(& (9#%'/?!=*.9) !=9% 123'/?!+*#$%&9#%<F,1"6"D,-0
P2.7]/KfL XO$&%('17)76(&)/"CB<"17623B*3!GH
D,(9'/?D,("8,(&1239#%'/?=-.7ML<"*3F-6(&)(*<M,&(" !BZD=-.7ML
!+*#$%&9#% 123*%'")*3G/$&G;(&("D,-0+-(9!*Y-!7Y9G@$ -(&!+*#$%&9#%
8/D?"4#A"P.-M.A"&("!?(b 123!+2#$%"!+*#$%&9#%CBD,("F",(123D,("
F2/& )D=(04("?"M.A"&("!4@0&!?(b )(*<M,1*&)D9()!)."CB%('
G;(<F,=(04("!=@0F(0123!+*#$%&9#%9@%(0N)(*<M,&(" 7$;(2&CD,

>)8@()8N785>A)
+D,)9%%&9;(:
! 7*-'=%?<F,1"6<'-6(CD,BZD=-.7ML!+*#$%&9#%123S%DB2/T)%%)
)6%"G;()(*7*-'=%?F*#%?;(*N&*/)J(
! %06(<M,"A;(9/"!M#A%!42.& !?"X." G."!"%*L 1%2)%e%2L F*#%-/=DN
B*3!]G!D@0-)/" !4*(3%('G;(<F,!+*#$%&9#%9@=@X@D'(& P.D*:BG*&
F*#%17)F/)CD,

19
 Makita Corporation
Anjo, Aichi, Japan

883891A379 www.makita.com
TRD