Temperature sensor installation

Orange
It is suggested to install the temperature White OFF signal
A.Components B.Technical parameters C. Factory setting sensor between the two front seats. The Yellow
Orange/Black
sensor should not be covered. White/Black
ECU, two transmitters, shock sensor, Voltage: 12V±3V Electric lock Baro lock Yellow/Black
J1.
ON signal
temperature sensor, tilt sensor (optional), Current: *20mA
Fig.3 Positive trigger
LED indicator, siren, battery charger, Frequency: 433.92MHZ J2. Passive arm Active arm
emitter, engine killer relay, engine start Siren SPL: 105~125dB Orange
Central locking system installation:
relay, wire harness. J3. Door trigger (-) Door trigger (+) White
1. For the vehicle with original electric central door lock, check its triggering type Yellow
Orange/Black
(negative or positive), then connect wires as per wiring diagrams Fig.2 or Fig.3. White/Black
2. For the vehicle with central locking system, the driver's door do not have motor, Yellow/Black
the other doors have motors. A new motor for driver's door is needed. Fig. 4.
3. For the vehicle with baro-lock, please change the jumper J1 at "Baro-lock" Fig 4. Positive / Negative trigger
position of the ECU. Fig. 5.
4. For the vehicle without central locking system, please install one set central
2-way car alarm system with engine start locking system to match with the car alarm system. Fig. 2.
D. Wiring diagram Baro-lock
unit
Orange Orange Orange

Main wire
Green/Blue
Brown (-)
Red/Blue (+)
White White OFF signal White
Yellow Yellow Yellow
Orange/Black Orange/Black Orange/Black
White/Black White/Black White/Black
Yellow/Black Yellow/Black
Yellow/Black
ON signal Door lock
switch
Fig.1 Principle Fig.2 Negative trigger Fig 5. Baro-lock circuit
To temperature sensor
Orange

White Fuse 15A

Trunk release circuit Siren installation
Yellow
Wires to central locking system
Orange/Black (Ref. Central locking system installation) Trunk switch Water

White/Black Fuse 15A

Red/ Pink

INSTALLATION MANUAL Yellow/Black

Red
Fuse 15A
Black(+)

Motor lock
To 12V Battery (+)
To mount the siren downwards to
Red/BlackFuse 5A To trunk prevent water dripping.
Brown Fuse 7.5A

ECU Pink
Brown
Black
Fuse 5A
Fuse 7.5A
To turn signal
To siren
To turn signal
Fuel pump cut circuit Series-mounting
with fuel pump
control wire
To GND Green
Yellow/Black (-)
Installation of LED indicator

White
Green
Shock sensor The LED indicator
should be installed Engine-killer relay
on the dashboard for
Blue To remote engine start warning the possible
Brown circuit thief.
Yellow Wiring methods to connect the engine
start detection wire
This wire has no voltage when the engine is not
started, and has positive voltage when the engine
is running.
Please choose only one method from the
following 3 connection methods.
1. Connect to the battery charger detection wire
Remote engine start circuit (+), this is the factory recommended connection.
2. Connect to the engine oil detection wire (+).

To ACC circuit (White)

To footbrake trigger (Orange)

To negative trunk trigger circuit (Red)

To positive/negative door trigger circuit (+/-) (Blue)

To engine start detection wire (Purple)

To fuel pump cut circuit (Yellow)

To handbrake switch (Green)

To engine power cut circuit (Yellow)

Transmitter ECU Voice siren Yellow

Brown Green
3. Five coils around high-tension coil.
Brown
Green
positive/negative door trigger circuit (+/-)
Blue

Engine killer relay

Blue(+)
Shock sensor Battery charger Temperature Tilt sensor
sensor (optional) Installation of emitter Learning button Dome light Door switch

To mount it on the top right To press and hold the learning button for
1. The emitter can be mounted at corner of the inner side of 10c
m 10 seconds, the LED indicator will turn on
the front windshield
cm

position * or *, if there's no solar

10

for 10 seconds and the siren will chirp once

* White Negative door trigger circuit (-)
film on the front windshield. To mount it on the back to indicate both former transmitters are
of the rear view mirror *
2. If the front windshield is covered (Suggested location) disabled.
Yellow (-) Blue(-)
with solar film, please remove the
Engine killer Remote Wire Dome light
LED light Emitter solar film within the dotted line before Door switch
relay start relay harness Engine power cut circuit
installing it at position *.
3. If all the windows are covered with
Installation of ECU Notice:
film, please mount it at position *.
Notes: 4. The emitter must be kept away 1. To connect the power wire (red) after
finishing all other wires connections.
Please choose the correct trigger type according
to the vehicle by changing the jump switch J3.
from any metal parts for at least 10 cm,
1.This unit is for 12V DC vehicle only. 2. The ECU should be fixed at a secrete
otherwise, the communication and Handbrake switch
2.This unit is to reduce the possibility of losing the vehicle place under dashboard.
operating distance will be affected. Negative trunk trigger circuit
by terrifying the thief and informing the owner of the vehicle Green (-)
status. Trunk illuminator Trunk switch
3.Please ask qualified engineer to install this unit. Indicator
4.The wiring should be kept away from high temperature
and high voltage places.
5.The wire joints should be insulated. Red (-)
Installation of tilt sensor (optional) Jump switch ACC circuit
We have achived ISO 9001 : 2000 & ISO/TS 16949 : 2002 White (+)
certifications by Rheinland (Germany) Co., Ltd. Stage LED Sensitivity
Led indicator
1 flash once low J1 J2 J3
2 flash twice high circuit of car Footbrake circuit
Sensitivity adjustment:
Door trigger(-)
Door trigger(+)
Electric lock
Baro lock

Passive arm
Active arm

3 flash 3 times highest Footbrake light

MANUFACTURED BY: button

Steelmate Co., Ltd. Footbrake

Mount horizontally
http: //www.steel-mate.com
E-mail: sales@steel-mate.com
Orange (+)